1. DL manuals
  2. Charnwood
  3. Saw
  4. W629
  5. Operator's Manual

Charnwood W629 Operator's Manual

Manual is about: 10” TABLE SAW

Summary of W629

  • Page 1

    10 ” table saw operators manual model: w629 charnwood, cedar court, walker road, hilltop industrial estate, bardon hill, leicestershire, le67 1tu tel. 01530 516 926 fax. 01530 516 929 email: sales@charnwood.Net website: www.Charnwood.Net.

  • Page 2: General Safety Rules

    General safety rules warning: do not attempt to operate the machine until you have read thoroughly and understood completely all instructions, rules, etc. Contained in this manual. Failure to comply may result in accidents involving fire, electric shock, or serious personal injury. Keep this owner's...

  • Page 3

    14. Disconnect the machine from power source before servicing and when changing the blade. 15. Never leave the machine running unattended. Turn the power off. Do not leave the machine until it comes to a complete stop. 16. Do not use any power tools while under the effects of drugs, alcohol or medic...

  • Page 4: Specification

    Specification table size 635 x420mm table size with extensions 635 x 1000mm motor (induction) 2200w, 240v, 3hp blade diameter x bore 250mm x 30mm blade rotation speed (no load) 4000 rpm maximum depth of cut at 90/45 degrees 70mm /45mm cutting width with table extension 720mm dust extractor hose conn...

  • Page 5: Assembly

    Assembly while the machine is on its side, take the four feet from the bag of parts and screw them into the four holes in the base. These feet can be adjusted by means of a spanner to level the saw table after the machine has been put into place. Return the saw to a vertical position. The cast iron ...

  • Page 6

    The extrusion with the measuring scale (rip fence guide rail) should be fitted to the front of the table, scale uppermost and in both cases the open side should face outwards. If they are difficult to slide on, make sure that you have slackened the nuts sufficiently and rock the extrusions gently as...

  • Page 7

    Slide the hose support clip onto the rear guide rail and lock it into place. Fit the dust collection hose to the saw guard and the spigot on the rear extraction point. Secure in place with the two hose clamps provided. Clip the hose into the support arm to hold it clear of the table. It is strongly ...

  • Page 8

    Identify the crosscut fence. Place it with the open side, face down and the plastic tip to the right. Slide the pivot block and the locking block onto the back side of the fence with the head of the bolt in the t-slot. The locking block has a t-shaped foot plate, slide it into the slot in the slidin...

  • Page 9: Using The Table Saw

    Using the table saw rip fence mitre fence blade angle adjuster blade angle lock blade height adjuster work clamp sliding carriage on/off switch work stop adjustable feet on/off switch slide the red section upwards and then lift the hinged cover. This will give you access to the green start and red s...

  • Page 10

    Making a cut ensure there is enough space around the table for the work piece before starting the cut. Position your feet in a stable and balanced stance. When feeding the timber, place your hands on the section of timber being kept. Never hold the waste part of the timber. Never force timber throug...

  • Page 11

    If an angle is to be cut, undo the thumb screw and ratchet lever, swing the fence to the desired angle and lock them both off. If necessary, undo both thumb screws and adjust the fence so that the plastic tip is just clear of the blade. Load the wood onto the carriage and screw down the work clamp t...

  • Page 12: Troubleshooting

    Troubleshooting problem cause remedy machine does not start blown fuse replace fuse loose switch terminal inspect back of switch faulty switch replace switch only starts when green button is held down faulty switch replace switch machine does not run but buzzing noise heard from motor failed capacit...

  • Page 13

    Declaration of conformity for ce marking charnwood declare that circular saw bench, model w629 conforms with the following directives: machinery directive 2006/42/ec low voltage directive 2006/95/ec and further conforms to the machinery example for which the ec type examination certificate no. Bm 50...

  • Page 14

    Charnwood w629 parts diagram a.

  • Page 15

    Charnwood w629 parts list a a01 foot a02 left / right base panel a03 hex nut m6 a04 washer m6 a05 base panel front a06 base panel rear a07 hex bolt m6 x 16mm a08 hex nut m5 a09 washer m5 a10 screw m5 x 12mm a11 dust outlet 100mm diameter a12 screw m6 x 16mm a13 washer m6 a14 saw faceplate a15 large ...

  • Page 16

    Charnwood w629 parts diagram b charnwood w629 parts list b b01 c shaped ring b02 sliding axle b03 eccentric bush b04 hex thin nut m8 b05 set screw m8 x 25mm b06 eccentric nut b07 trolley b08 washer m6 b09 t-shape bolt b10 set screw m8 x 10mm b11 eccentric nut b12 csk screw m6 x 35mm b13 thumb screw ...

  • Page 17

    Charnwood w629 parts diagram c charnwood w629 parts list c c01 screw m6 x 16 c02 dust collector c03 hex bolt m8 x 16mm c04 washer m8 c05 blade locking washer c06 saw blade c07 driven pulley c08 circlip m20 c09 bearing 6204 c10 circlip m47 c11 saw axis c12 parallel plate c13 spring washer m16 c14 thi...

  • Page 18

    C49 pin 8 x 110mm c50 hex locking nut m12 c51 washer m12 c52 key 5 x 15 c53 circlip m16 c54 bolt shaft c55 hex nut m8 c56 hand wheel c57 washer m12 c58 hex nut m12 span blade lock spanner cap capacitor 20uf 450vac m8 stud charnwood w629 parts diagram d charnwood w629 parts list d d01 locking handle ...

  • Page 19

    Charnwood w629 parts diagram e charnwood w629 parts list e e01 t shaped runner e03 mitre gauge e04 washer m8 e05 long handle.

  • Page 20

    Charnwood, cedar court, walker road, hilltop industrial estate, bardon hill, leicestershire, le67 1tu tel. 01530 516 926 fax. 01530 516 929 email: sales@charnwood.Net website: www.Charnwood.Net.