Chass 00185 Instruction Manual - page 2
ACTIVATING THE ALARM AND SNOOZE:
1. Slide
the
ALARM
ON / OFF switch to
“ON”
position on the side of the clock. The alarm symbol (
z)
will appear on
the display.
2. The alarm will activate at the pre-set time and sound for 60 seconds.
3. When the alarm activates you may press the
SNOOZE / LIGHT
button and the alarm will stop and activate again
after about five (5) minutes. The alarm symbol (
z)
will flash. This snooze feature may be repeated over and over
again.
4. To fully shut off the alarm, slide the
ALARM
ON / OFF switch to “
OFF
” position.
TO SET THE DST (DAYLIGHT SAVING TIME):
Press the
DST
button once to turn ON / OFF the DST (Daylight Saving Time).
The DST symbol (
☼
) will appear on the display to indicate summer time. Turn this feature ON to adjust the time by one
hour. At the end of DST simply press the button again and the time will move back one hour.
DISPLAY MODES:
(Located at the back of the clock)
Press the
ALARM,
2ND.TIME, CALENDAR
button to select between:
Alarm time display, the word “
ALARM
”
appears on the display.
2nd Time zone display, a “
DT”
icon will appear on the display.
Calendar display,
“M”
& “
D”
icon will appear on the display.
SMARTLITE:
1. To operate the Smartlite, simply slide the
SENSOR
ON / OFF
switch to the
“
ON
” position. The display will stay
illuminated in a dark environment until you slide the
SENSOR
ON / OFF
switch to the
“
OFF
” position.
2. The Smartlite function may be used up to eight (8) hours per day for 365 days .The less the Smartlite function is used
the longer the battery life.
NOTE: TO SAVE THE BATTERY POWER, YOU MUST SLIDE THE SENSOR SWITCH TO THE ”OFF
”
POSITION
WHEN THE CLOCK COVER IS CLOSED OR IS PLACED IN A SUITCASE OR DRAWER.
BACK LIGHT:
Press the
SNOOZE / LIGHT
button to light up the display.
NOTE
: Frequent use of the back-light will drain the batteries faster.
MANUAL SETUP:
(time and date reset)
1. Move the
TIME ZONE
switch to your desired time zone
2. Slide the
DATE / ALARM / LOCK / TIME
switch to the
DATE
position
3 .Press and hold down the
YEAR
button to adjust the correct year
4. Press and hold down the
MONTH
button to adjust to the correct month
5. Press and hold down the
DATE
button to adjust to the correct date
6. Slide the
DATE / ALARM / LOCK / TIME
switch to the
TIME
position
7. Press and hold down the
HOUR
button to adjust to the correct hour, making sure AM / PM is set correctly, the
”
PM
”
indicator will appear on the display for PM time only
8. Press and hold down the
MINUTE
button to adjust to the correct minute
9. Slide the
DATE / ALARM / LOCK / TIME
switch to the
“LOCK”
position to complete the time and date setting
DUAL POWER OPERATED:
This clock is designed to operate using solar power and LITHIUM Battery .The battery life remains approximately 3-4
years if the clock is used in light at least 200 lux for 10 hours per day. If you are not going to use the alarm clock slide the
TIME ZONE
switch to the “
DISPLAY OFF
” position to save battery life.
CHANGING THE BATTERIES:
Open the
BATTERY COVER
located at the back of the clock and insert two #2450 3.0V
LITHIUM
batteries into the
battery compartment as indicated by the polarity markings, then follow the instructions to reset the clock.
MANUAL RESET:
Use a pin through the
RESET
hole to push in the
RESET
Button. You will then follow the
MANUAL SETUP
procedure to
reset the clock.
MAINTENANCE:
A soft cloth may be used to clean your clock. Do not use any corrosive cleaner or chemical solutions on the clock. Keep
the clock clean and try to avoid any problems.
ENVIRONMENTAL PROTECTION:
Disposal of electrical & electronic equipment:
Do not dispose of this product with household waste. For the proper treatment, recovery and recycling, please take this
product to the appropriate collection point. If you are unsure of where this is, contact your local authority; improper
disposal may be harmful to the environment.