- DL manuals
- Chauvet
- Lighting Equipment
- DV Wall DVM-HR
- User Manual
Chauvet DV Wall DVM-HR User Manual
Summary of DV Wall DVM-HR
Page 1
Dvm-hr dv wall™ user manual chauvet, 3000 n 29 th ct, hollywood, fl 33020 u.S.A (800) 762-1084 – (954) 929-1115 fax (954) 929-5560 www.Chauvetlighting.Com 2007-02-05 / 16:45.
Page 2: Table of Contents
Table of contents table of contents 1. Before you begin....................................................................................................................................................... 3 u npacking i nstructions .....................................................................
Page 3: 1. Before You Begin
1. Before you begin unpacking instructions immediately upon receiving a product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appe...
Page 4: Important Safety Information
Before you begin important safety information this product is designed for professional use. This product presents risks of lethal or severe injury due to fire and heat, electric shock, and injury from falls. Read this manual before installing or powering the fixture, follow the safety precautions l...
Page 5: 2. Introduction
2. Introduction overview the dv wall is both an indoor and outdoor led video wall display suitable for a wide range of applications. An ip65 rating ensures reliable and safe operation in most weather conditions. The dv wall can be seen comfortably during daytime or night time hours. The dv wall’s mo...
Page 6: Product Overview
Introduction introduction product overview 1 panel 1 driver can handle 6 panels wide by 16 panels high. Horizontal width: 6 panels or (96 vertical lines/columns) vertical height: 16 panels or (256 horizontal lines/rows) maximum size matrix using 1 driver resolution: 16 vertical lines/columns r e sol...
Page 7: 3. Hardware Setup
3. Hardware setup ac power warning! Verify that the power requirement label on your unit matches the line voltage applied. All fixtures must be connected to circuits with a suitable earth ground. • to determine the power requirements for a particular fixture, see the label affixed to the back plate ...
Page 8: Maximum System Configuration
Maximum system configuration 1 2 3 4 5 6 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 d8 d1 d9 d10 d11 d12 d13 d14 d15 d16 d2 d3 d4 d5 d6...
Page 9: Mounting System
Setup mounting system each dv wall panel comes with a square bracket with interlocking connectors that must first be bolted to the two tracks located on opposite sides of the back of the panel using the provided m10 hex bolts. Affix the square bracket to the back of the dv wall panel using the provi...
Page 10
Setup flying bracket attachment the flying bracket attachment is used to fly or rig a 1 meter width section of a dv wall. It is designed to be attached to the very top row of a 1 meter section. Additional hardware is provided for interconnecting multiple flying brackets. 1 2 3 4 i tem d escription 1...
Page 11: Signal & Power Configuration
Setup setup signal & power configuration rj-45 vga dvi com ou t 1 out 2 dvi rj-45 1~256row 257~512row d vi si g n al c abl e display card transmitter rs 232 s ig n a l ca bl e net cable driver 2 j16 j15 j14 j13 j12 j11 j10 j9 j8 j7 j6 j5 j4 j3 j2 j1 in out next driver 1 j16 j15 j14 j13 j12 j11 j10 j...
Page 12: Dv-Wall Driver
Setup dv-wall driver every driver contains 16 output ports (j1 ~ j16). Each output port provides signal source to one horizontal row of panels not exceeding 6 panels wide. 1 2 3 4 5 6 j1 j2 j3 j4 j5 j6 j7 j8 j9 j10 j11 j12 j13 j14 j15 j16 rear view j1 6 j15 j14 j13 j12 j1 1 j10 j9 j8 j7 j6 j5 j4 j3 ...
Page 13
Setup dipswitch settings a dv-wall video display matrix may consist of up to 16 drivers or 16 individual grid sections in various pattern configurations. Each driver must be addressed according to your configuration so that the video displayed appears whole and intact. Two internal dipswitches (jp1 ...
Page 14
Setup jp2 dipswitch in order for video to display properly across multiple sections or drivers, each driver must be addressed accordingly. The jp2 dipswitch establishes the horizontal starting address or (vertical line) for each section of matrix. Horizontal line 16 lines/pixels vertical line, jp2 s...
Page 15: Transmitter Card
Setup transmitter card install the transmitter card in an available pci slot in your computer. The transmitter card is the interface between your pc, dv-wall studio software and the dv-wall screen. You must use the dvi cable provided to connect from the computers dvi output to the dvi port on the tr...
Page 16
Setup example system configurations 4:3 aspect ratio 4 meters by 3 meter front view starting address: 0 96 pixels wide or 96 vertical lines 32 pixels wide or 32 vertical lines driver j output ports starting address: 96 j1 j2 j3 j4 j5 j6 j1 j2 j3 j4 j5 j6 driver 2 driver 1 driver 1 system information...
Page 17
Setup 16 meters by 12 meters starting address: 0 driver 1 width = 32 jp1 1 2 3 4 5 6 7 8 9 10 11 12 0 1 0 0 0 0 0 0 0 0 0 0 start = 480 jp2 1 2 3 4 5 6 7 8 9 10 11 12 1 1 1 0 0 1 1 0 0 0 0 1 driver 3 width = 96 jp1 1 2 3 4 5 6 7 8 9 10 11 12 0 1 0 1 0 0 0 0 0 0 0 0 start = 288 jp2 1 2 3 4 5 6 7 8 9 ...
Page 18
Setup 16:9 aspect ratio 8 meters by 4.5 meters j7 j8 j9 j7 j8 j9 j7 j8 j9 front view starting address: 0 96 pixels wide or 96 vertical lines starting address: 96 j1 j2 j3 j4 j5 j6 driver 3 driver 2 driver 1 width = 64 jp1 1 2 3 4 5 6 7 8 9 10 11 12 0 1 1 0 0 0 0 0 0 0 0 0 start = 192 jp2 1 2 3 4 5 6...
Page 19
Setup special applications pattern 1 j1 j2 j3 j4 j5 j6 j1 j2 j3 j4 j6 j1 j2 j3 j4 starting addr: 0 starting addr: 64 j5 starting addr: 128 starting addr: 176 d4 d3 d2 d1 64p 64p 48p 32p system information vertical lines: 208 horizontal lines: 96 resolution: 208 x 96 pix size: 6.5m x 3m panels: 52 (p...
Page 20: 4. Appendix
4. Appendix returns procedure returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a return merchandise authorization number (ra #). Products returned without an ra # will be refused. Call chauvet and request ra # p...
Page 21: Technical Support
Appendix technical specifications (per panel) weight & dimensions length........................................................................................................................... 19.8 in (501 mm) width ....................................................................................