Summary of Mini Moon LED 360
Page 1
User manual.
Page 2: Able of
Chauvet®, 2010, all rights reserved information and specifications in this user manual are subject to change without notice. Chauvet® assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. Rev01b t able of c ontents 1. Before you begin ....................
Page 3: Efore
1. Before you begin 3 8/31/2010 4:41 pm 1. B efore y ou b egin what is included 1 x mini moon ™ led 360 1 x mounting bracket with nuts (2), washers (2) & bolts (2) 1 x power cord 1 x warranty card 1 x user manual unpacking instructions immediately upon receiving a fixture, carefully unpack the carto...
Page 4
1. Before you begin 4 8/31/2010 4:41 pm safety instructions please keep this user manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. Always make sure that you are connecting to the proper voltage, and that the line voltage y...
Page 5: Ntroduction
2. Introduction 5 8/31/2010 4:41 pm 2. I ntroduction compact, panning led moonflower effect with 540-degrees of rotation combines a multi-colored beam effect and a moving head into a single fixture super-crisp optics create dazzling mid-air effects and sharp beams of light for surface projection inc...
Page 6
2. Introduction 6 8/31/2010 4:41 pm product overview front lens dmx in bracket adjustment knob hanging bracket (2) dmx out power out fuseholder power in microphone sensitivity adjustment knob control panel (led display) microphone.
Page 7: Etup
3. Setup 7 8/31/2010 4:41 pm 3. S etup ac power this fixture runs on 100~240 vac, 50/60 hz. Before powering on the unit, make sure the line voltage to which you are connecting it is within the range of accepted voltages. To determine the power requirements for a particular fixture, see the label aff...
Page 8
3. Setup 8 8/31/2010 4:41 pm mounting orientation the mini moon™ led 360 may be mounted in any position provided there is adequate room for ventilation. Rigging be sure that the structure can support the weight of the fixture. Please see the “technical specifications” section of this manual for a de...
Page 9: Perating
4. Operating instructions 9 8/31/2010 4:41 pm 4. O perating i nstructions configuring the starting address the mini moon™ led 360 fixture uses seven dmx channels. The highest channel that the fixture may be set to in order to function properly is 506. Any address higher than this will prevent access...
Page 10
4. Operating instructions 10 8/31/2010 4:41 pm dmx operation this is the operating mode, which will allow for control using an external dmx controller. You must set the starting address for this mode. If this is your first time using dmx, refer to t he “dmx primer” section in the appendix of this ma...
Page 11
4. Operating instructions 11 8/31/2010 4:41 pm automatic this fixture has five preprogrammed chases with adjustable speed. Access these via the control panel of the front of the fixture. Please see the instructions below for further details. 1. Press until ~ appears on the led screen. 2. Press . 3. ...
Page 12
4. Operating instructions 12 8/31/2010 4:41 pm dmx channel values c hannel v alue f unction 1 000 255 pan 0~540° 2 000 255 pan speed fast ~ slow 3 000 006 007 014 015 022 023 030 031 038 039 046 047 054 055 062 063 070 071 078 079 086 087 094 095 102 103 110 111 118...
Page 13: Ppendix
5. Appendix 13 8/31/2010 4:41 pm 5. A ppendix general troubleshooting s ymptom p ossible c ause ( s ) p ossible a ction ( s ) breaker/fuse keeps blowing excessive circuit load check total load placed on the electrical circuit. Short circuit along the power wires check for a short in the electrical w...
Page 14
5. Appendix 14 8/31/2010 4:41 pm dmx primer there are 512 channels in a dmx connection. A fixture capable of receiving dmx will require one or a number of sequential channels. The user must assign a starting address on the fixture that indicates the first channel reserved in the controller. There ar...
Page 15
5. Appendix 15 8/31/2010 4:41 pm cable connectors cabling must have a male xlr connector on one end and a female xlr connector on the other end. Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a ground loop, and your fixture may perform errati...
Page 16
5. Appendix 16 8/31/2010 4:41 pm 3-pin to 5-pin conversion chart if you use a controller with a 5-pin dmx output connector, you will need to use a 5-pin to 3-pin adapter. The chart below details a proper cable conversion: 3-p in to 5-p in c onversion c hart conductor 3-pin female (output) 5-pin male...
Page 17
5. Appendix 17 8/31/2010 4:41 pm general maintenance to maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build up ...
Page 18: Echnical
T echnical s pecifications weight & dimensions length.......................................................................................................... 5.7 in (145 mm) width ........................................................................................................... 6.8 in (17...