- DL manuals
- Chauvet
- Light Fixture
- Q-Spot 250
- User Manual
Chauvet Q-Spot 250 User Manual
Summary of Q-Spot 250
Page 1
Chauvet, 3000 n 29 th ct, hollywood, fl 33020 u.S.A (800) 762-1084 – (954) 929-1115 fax (954) 929-5560 www.Chauvetlighting.Com 2005-10-09/22:09 q-spot250 q-spot ™ 250 q-wash250 q-wash ™ 250 user manual q-spot ™ 250 q-wash ™ 250
Page 2: Table Of Content
Q-wash & q-spot 250 user manual 2 2005-10-09/22:09 table of content before you begin....................................................................................................................................................... 3 w hat is included ...............................................
Page 3: Efore
Q-wash & q-spot 250 user manual 3 2005-10-09/22:09 b efore y ou b egin what is included q-spot250, q-spot ™ 250 or q-wash250, q-wash ™ 250 5 extra gobos (q-spot ™) power cord with plug hsd-250 discharge lamp manual warranty card unpacking instructions immediately upon receiving a fixture, carefully ...
Page 4: Ntroduction
Q-wash & q-spot 250 user manual 4 2005-10-09/22:09 i ntroduction technical features q-spot ™ 250 13 channel dmx intelligent moving yoke pan: 530° tilt: 280° pan/tilt speed lamp on/off, reset color wheel - 7 colors plus white - rainbow color spin at variable speeds 3-facet high speed rotating prism r...
Page 5
Q-wash & q-spot 250 user manual 5 2005-10-09/22:09 product overview segment buttons i/o panel overview b uttons i/o p anel mode toggles programming functions dmx out & in dmx-512 connectors down steps backward through menu functions power ac input iec 60320 c14 and fuse holder up steps forward throu...
Page 6: Etup
Q-wash & q-spot 250 user manual 6 2005-10-09/22:09 lamp cover thumbscrews top cover s etup lamp m a x i m i z i n g t h e l i f e o f y o u r l a m p to ensure the longest and most efficient use of the lamp always wait between 10 and 15 minutes before re-applying power after a shutdown. Failure to d...
Page 7
Setup q-wash & q-spot 250 user manual 7 2005-10-09/22:09 optimum distance 1 to 1.5mm incorrect! Keep optimum distance 1-1,5mm screw b screw a warnin g! La mp is h ot! Ris k of fire p rote c h and s a nd eye s. Wait a l eas 15 min b efo re o pen ing the co vers an d re mo vin g la mp from th e fi xtu...
Page 8
Setup q-wash & q-spot 250 user manual 8 2005-10-09/22:09 e xte rio r su rface temperatu re t= 80 ° c warning! Wait at least 15 min. Before opening the covers and removing x y z a c b lamp alignment screws, a, b & c l a m p i n s t a l l a t i o n ( q - w a s h ™ 2 5 0 ) 1. Remove screws labeled x, y...
Page 9
Q-wash & q-spot 250 user manual 9 2005-10-09/22:09 power warning! Verify that the internal multi-tap transformer is set to match the line voltage applied. All fixtures must be connected to circuits with a suitable earth ground. To determine the power requirements for a particular fixture, see the la...
Page 10
Setup q-wash & q-spot 250 user manual 10 2005-10-09/22:09 w a r n i n g it is important never to obstruct the fan or vents pathway. The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation. The installa...
Page 11: Perating
Q-wash & q-spot 250 user manual 11 2005-10-09/22:09 o perating i nstructions control panel on the control panel you can set the dmx address, set the fixture to master/slave mode, reset the fixture and change fixture personality trait. Control panel functions f unction o ptions n otes pan no/yes pan ...
Page 12
Q-wash & q-spot 250 user manual 12 2005-10-09/22:09 daisy chain connection operating modes a stand-alone mode will listen to sound and run through its diverse range of built in programs. Master/slave mode will allow the command of up to as many units you want in a synchronized light show to the soun...
Page 13
Operating instructions q-wash & q-spot 250 user manual 13 2005-10-09/22:09 dmx-512 addressing this mode enables the use of a universal dmx controller device. Each fixture requires a "start address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data on the cha...
Page 14: Ppendix
Q-wash & q-spot 250 user manual 14 2005-10-09/22:09 a ppendix dmx primer there are 512 channels in a dmx-512 connection. Channels may be assigned in any manner. A fixture capable of receiving dmx-512 will require one or a number of sequential channels. The user must assign a starting address on the ...
Page 15
Appendix q-wash & q-spot 250 user manual 15 2005-10-09/22:09 dmx values q-spot ™ 250 c hannel v alue f unction 1 000 255 pan left > right ( 128 = center) 2 000 255 tilt up > down (128 = center) 3 000 255 pan (fine) 16 bit 4 000 255 tilt (fine) 16 bit 5 000 255 pan/tilt speed fast > slow 6 000 127 12...
Page 16
Appendix q-wash & q-spot 250 user manual 16 2005-10-09/22:09 q-wash ™ 250 c hannel v alue f unction 1 000 255 pan left > right ( 128 = center) 2 000 255 tilt up > down (128 = center) 3 000 255 pan (fine) 16 bit 4 000 255 tilt (fine) 16 bit 5 000 255 pan/tilt speed fast > slow 6 000 127 128 139 140 2...
Page 17
Appendix q-wash & q-spot 250 user manual 17 2005-10-09/22:09 maintenance to maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a mo...
Page 18
Appendix q-wash & q-spot 250 user manual 18 2005-10-09/22:09 general troubleshooting applies to symptom solution(s) lights foggers & snow controllers dimmers & chaser auto shut off check fan thermal switch reset beam is very dim or not bright clean optical system or replace lamp check 220/110v switc...
Page 19
Appendix q-wash & q-spot 250 user manual 19 2005-10-09/22:09 technical specifications weight & dimensions q-wash ™ 250 length...................................................................................................................... 379 mm (14.92 in) width....................................