Conair HC200WXCSC Instructions For Care And Use

Summary of HC200WXCSC

  • Page 1

    Conair thanks you for choosing our brand of hair clipper. With practice you will soon be doing a professional job every time you use the unit. This is a well-engineered, high quality product, and we know that with proper care it will give you years of reliable service. Thanks again for choosing cona...

  • Page 2: Important

    Important safety instructions when using electrical appliances, especially when children are present, basic safety precautions should always be taken, including the following: read all instructions before using keep away from water danger- any appliance is electrically live, even when the switch is ...

  • Page 3: Warning-

    Warning- to reduce the risk of burns, electric shock, fire, or injury to persons: 1. This appliance should never be left unattended when plugged in. Do not pull, twist, or wrap line cord around appliance. 2. Close supervision is necessary when this appliance is used by, on, or near children or inval...

  • Page 4: Save These

    Save these instructions operating instructions this appliance is intended for household use. Use on alternating current 120v ac/60hz only. This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in the outlet only one way. If the plug does not...

  • Page 5: The Conair Guide

    The conair guide to cutting hair at home before you start: 1. Inspect your clipper. Make sure it’s free of hair and dirt, properly oiled, and running smoothly. 2. Place a towel around the neck of the person. 3. Seat the person so that their head is at your eye level.This gives you greater visibility...

  • Page 6: Hair At Its Own Speed.

    Attach combs by holding them teeth up then snapping onto the bottom of the clipper blade. To remove comb attachments place index finger and thumb as illustrated; then pull out and up. Note: never push or shove the clipper through the hair to make it move more quickly. Professional experience shows t...

  • Page 7

    Repeat around sides and back of head. If you want hair to be even shorter: a) a p p l y m o r e pressure to the head with the attachment comb that is in place. This takes a little practice of course. Or b) just switch to a shorter attachment comb. Remember, it’s better to leave too much hair than to...

  • Page 8: Outlining:

    Outlining: outlining requires no attachments. Comb hair into the desired style. Position the clipper between the sideburns and the ear (see below), making sure the corner edge of the blade is against the hairline. With the outline of the hair as your guide, slowly move the clipper over, around and b...

  • Page 9: Short Cuts to Perfect

    Short cuts to perfect flat tops, crew cuts, etc. Always cut from the back of the neck to the crown, using the longest comb setting. Hold the comb attachment flat against the head and slowly move the clipper up through the hair. Use the same technique for the sides, cutting from the bottom to the upp...

  • Page 10: User-Maintenance

    User-maintenance instructions care of your clippers if you determine that blade alignment is incorrect: maintenance of the blade always apply oil to the blades before, during and after use. This will ensure maximum cutting performance. Hold clipper away from your body in a downward position and appl...

  • Page 11: Special Oil

    *the extreme left-hand tooth of the cutting comb must cover or be to the extreme left hand of the first small tooth of the cutter. *be sure that the extreme right hand big tooth of the cutter touches the extreme right hand tooth of the cutting comb. Any other servicing should be performed by an auth...

  • Page 12: Maximum Power Setting.

    2. Then turn the screw counter-clockwise, just until noise stops. This is the maximum power setting. 1. With screwdriver or dime, turn the power screw clockwise until arm strikes the coil, making a clacking noise. Adjustable taper lever just like professional clippers, the conair taper lever is posi...

  • Page 13

    Taper lever up as far as it will go. To increase cutting length, slowly push lever down. If you push to the lowest position, it will leave hair about the same length as the short attachment. Because a different cutting edge is used in each setting, the taper lever lengthens the life of your blades. ...

  • Page 14

    Bottom blade adjustable taper lever switch top blade power screw.

  • Page 15: Keep Away From Water

    Keep away from water everyone knows that electricity and water are a dangerous combination. But did you know that an electric appliance is still electrically alive even if the switch is off? If the plug is in, the power is on. So when you are not using your appliances, keep them unplugged. Always un...

  • Page 16: Limited Five Year Warranty

    Limited five year warranty conair will repair or replace (at our option) your unit free of charge for 12 months from the date of purchase if the appliance is defective in workmanship or materials. To obtain service under this warranty, return the defective product to the service centre listed below ...