Conair Weight Watchers WW87C Instructions For Use
Instructions
for use of
Weight Watchers
bathroom scale
Congratulations! By purchasing this Weight Watchers Scale, you’ve made the
first step toward taking control of your weight. To get the greatest benefit from
your purchase, please read this entire brochure before using your scale.
©2007 Conair Consumer Products. 100 Conair Parkway, Woodbridge, Ontario. L4H 0L2. Made in China.
©2007 Weight Watchers International Inc. All rights reserved. Weight Watchers is the
registered trademark of Weight Watchers International Inc. and used under license.
Service Centre
Conair Consumer Products Inc.
100 Conair Parkway,
Woodbridge, Ontario.
L4H 0L2
Made in China
Consumer Call Centre E-mail:
Consumer_Canada@Conair.com
1-800-472-7606
www.conaircanada.ca
07CN10231
IB-7734
LIMITED TEN YEAR WARRANTY
Conair will repair or replace, at our option, your appliance free of charge for 120
months from the date of purchase if the appliance is defective in workmanship
or materials.
To obtain service under this warranty, return the defective product to the service
center listed below that is nearest you, together with your sales slip and $7.00 for
postage and handling.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 120-MONTH
DURATION OF THIS WARRANTY.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY,
EXPRESS OR IMPLIED, WHATSOEVER.
This warranty gives you specific legal rights,
and you may also have other rights which vary from province to province.
Scales by
™
Model WW87C
Display and store data
1. Once the gender is set, data storage is complete.
2. User number displays for a few seconds, Height displays for a few seconds, and
Age for another few seconds.
3. The scale is now ready for body analysis measurements.
NOTE:
In personal data setting mode, the scale returns to standby mode automatically if
no button is pressed within 30 seconds.
Body Analysis Measurement
1. Operate the scale on a secure flat floor. In standby
mode, press the User button repeatedly until the
display shows your user number. The scale will display
your personal data (height, age, gender) and then
display "0.0".
2. Step on the scale barefoot with your feet aligned on
the two electrodes on the glass. Weight shows for
several seconds.
3. After several seconds, body fat weight, body fat
percent, body water and bone mass data are shown
on the bottom line of the display
4. The scale shuts off automatically.
NOTE:
If you step on the scale before “0.0” appears or if your
feet are not aligned on the electrodes, the scale will
not function properly.
Before Using Scale
Precautions for Use
CAUTION! Use of this device by persons with any electrical implant such
as a heart pacemaker, or by pregnant women, is not recommended.
1. Set switch on the base of the scale to measure in pounds (lb) or kilograms (kg).
2. Set scale on floor. Surface must be level for accurate operation and safety.
Weight Measurement Only
To measure weight only:
1. Operate the scale on a secure flat floor.
2. Choose pounds (lb) or kilograms (kg) by switching
the convertible switch on rear of scale.
3. Tap the scale in standby mode. Whole screen
appears.
4. Wait until all digits light for 2 seconds and
“0.0” appears.
5. Step on the scale and stand still to measure
your weight.
6. Step off the scale and it will shut off automatically.
Personal Data Setting Mode
Set User ID
1. In standby mode, press Set button, the number
“USER 1” will appear and flash.
2. Use user button to select a user number among
4 user numbers (USER 1 to USER 4).
Set Height
1. Press Set button to confirm the user ID and enter
Height setting mode.
2. Use Up or Down button to set your height.
Set Age
1. Press Set button to confirm height and enter Age
setting mode.
2. Use Up or Down button to set your age.
Set Gender
1. Press Set button to confirm age and enter gender
setting mode.
2. Press up and down button to select female or male
icon and then press Set button to confirm gender
selection.