- DL manuals
- Conairphone
- Answering Machine
- TAD1212
- Owner's Manual
Conairphone TAD1212 Owner's Manual
Summary of TAD1212
Page 1
Reduce 74.3% printed. Ib size is 105 x 138 mm.(ib-xxxx) callkeeper digital answering system model tad1212 r owner's manual play messages battery low message stop / save r e peat an noun cem ent on/off answering system c a l lkeepe r r digit al a u d i l conair r phone.
Page 2: Location Of Controls
2 location of controls play messages battery low message st o p / sa ve r e pea t an no un ce men t on/o ff answering system speaker ac power connection repeat control microphone volume control stop/save control power on/battery low/message indicator led announcement record/check control system on/o...
Page 3
3 important safety instructions when using your telephone equipment, basic safety procedures should always be followed to reduce risk of fire, electric shock and injury to persons including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the ...
Page 4
4 important safety instructions (cont.) a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 12. Do not use the telephone to report a gas leak in the vicinity of a leak. 13. Do not allow anything to rest on power cord. Do not locate this product w...
Page 5
5 caution (cont.) for a long period of time (several months or more) since during this time the battery could leak in the product. 9. Properly discard dead batteries as soon as possible since dead batteries are more likely to leak in a product. 10. Do not store this product, or the batteries provide...
Page 6
6 installation (cont.) 3. Install one 9 volt battery. 4. Replace battery compartment door screw and connect the ac adaptor. 5. Install a replacement battery once a year to ensure proper operation of the power failure protection feature. 1. Plug your telephone into the modular tel jack in the back of...
Page 7
7 understanding your message indicator led (why the green light is flashing) message indicator status reason action message indicator is consistently flashing slowly. Message indicator flashes rapidly. Message indicator flashes to indicate number of messages received and then repeats. Message indica...
Page 8
8 message playback when the message indicator flashes, pauses, and repeats you have received messages. The number of flashes indicates the amount of messages received (up to 10) 1. Press and release the play messages control on your unit. 2. The unit will automatically playback your messages in the ...
Page 9
9 special features (cont.) if you don`t want to talk to the caller, just let your unit take a message, adjust the volume control on the side of the unit to listen. If you don`t want to listen to the caller`s message, lower the volume. Note: callers will be unaware that you are screening their calls,...
Page 10
10 special features (cont.) power failure protection/battery back up to reset important during a power outage, your unit will not function even if a 9 volt battery is installed. The battery will save your outgoing message and any incoming messages you may already have received so that you can play t...
Page 11
11 remote operation remote security code remote turn on messages playback there is a three digit security code located on the bottom of your unit. Remember this number. You will need it to get your messages by remote when calling from a touch-tone phone. A space has been provided on the enclosed qui...
Page 12
12 if you have followed the instructions in this manual, and have difficulty operating your callkeeper answering system, locate the problem in the left column below. Check the corresponding possible cause and corrective action columns to locate and remedy problem. If the solution to your problem is ...
Page 13
13 problem no answer no power no incoming messages recorded possible cause ac adaptor is disconnected from wall outlet or back of unit ac adaptor is disconnected from wall outlet or back of unit unit is in the "off" mode power to electrical outlet may be off power to electrical outlet may be off tel...
Page 14
14 problem no remote operation the machine is cutting off incoming messages the machine beeps during the recording of my outgoing messages after a power outage, outgoing announcement and incoming messages are lost possible cause unit is in the "off" position security code not entered correctly remot...
Page 15
Your telephone company may make changes in its facilities, equipment, operation or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. If you experience trouble with...
Page 16
16 changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. The...