Summary of ULTIMAX
Page 2
Using the ultimax child car seat 0236-02 to safeguard your child you have opted for our concord ultimax seat. This product is manufactured under strict quality controls. Its excellent safety features work best when the seat is used in accordance with legal requirements. Be sure, therefore, to comply...
Page 3
2 1 1. Rear-facing installation (from birth to 13 kg) 0237-02 important! Do not use on seats with airbags. Extreme danger! Turn the rotary handle at the front of the seat shell upwards (1) and at the same time push the seat shell into the upright position (2). Hold the seat shell with your thumbs on...
Page 4: Click
Click 1. Rear-facing installation (from birth to 13 kg) 0238-01 pass the car seat belt over the top of the base unit and secure the belt in the buckle. Position the lower belt section (1) (lap belt) under the blue lap belt guides (see illustration). Pass the upper belt section (2) (diagonal belt) ar...
Page 5
1. Rear-facing installation (from birth to 13 kg) 0239-01 wrong belt positioning! Belt positioning when the base unit is installed correctly. 1.6 0119-06 1.7 0118-04.
Page 6: Click
1. Rear-facing installation (from birth to 13 kg) 0240-02 hold the seat shell as illustrated and position it on the base unit. Press the seat shell downwards until it clicks audibly into position. Always check that when the seat shell is inserted a green dot is visible on both sides through the open...
Page 7
2 1 2. Front-facing installation (from 9 to 18 kg) 0241-01 important! Front-facing installation is only suitable from a body weight of 9 kg and without the pelvic insert, see section 6.5! Turn the rotary handle at the front of the seat shell upwards (1) and push the seat shell into the upright posit...
Page 8: Click
Click 2. Front-facing installation (from 9 to 18 kg) 0242-01 pass the car seat belt over the top of the base unit and secure the belt in the buckle. Insert the lower belt section (lap belt) into the lap belt guides (red) as illustrated. Open the red belt clip on the belt tensioner. 0030-04 0031-05 0...
Page 9
2. Front-facing installation (from 9 to 18 kg) 0243-02 turn the open side of the ratchet shaft upwards. Position the upper belt (diagonal belt) in the opening of the ratchet shaft and into the guide mechanism behind it. The belts must not be twisted! 0029-08 0037-09 2.8 2.7.
Page 10
1 2 2. Front-facing installation (from 9 to 18 kg) 0244-01 tighten the upper belt (1) slightly and close the red belt clip (2). Then tighten the belt once again. Use the ratchet to wind the belt up until the base unit is firmly secured in the car seat. The belt must be taut. The base unit must be po...
Page 11
2. Front-facing installation (from 9 to 18 kg) 0245-01 belt positioning when the base unit is installed correctly. The buckle for the vehicle safety belt must not come above the edge of the lap belt guide. If in doubt or if you are still uncertain, please contact concord. 0121-03 0073-05 2.12 2.13.
Page 12: Click
2. Front-facing installation (from 9 to 18 kg) 0246-00 always check that when the seat shell is inserted a green dot is visible on both sides through the opening on the side pieces. This indicates that the seat is installed correctly. Disassembly is done in the reverse order (see 1.1 and 1.2). To re...
Page 13
3. Securing the child 0247-00 open the belt buckle and open the child seat belts outwards to lie on the armrests. Then put the child into the seat shell so that its back rests against the backrest. The central adjuster is located at the front of the seat, beneath the cover. This secures the central ...
Page 14: Click
3. Securing the child 0248-02 tension the belt system by pulling the belt of the central adjuster until your child is securely strapped in. Please check that both the shoulder and lap belts are tensioned equally. To take the child out, press the red “press” button on the belt buckle of the harness s...
Page 15
4. Adjusting the seat to the child’s size / adjusting the head support and harness 0249-03 grasp the head support at the top and pull it forwards. You can then set it to the height that is right for your child. There are six possible different positions. Attention! Always make sure the belt is posit...
Page 16
4. Adjusting the seat to the child’s size / adjusting the head support and harness 0250-02 on the rear of the seat shell, separate the two belts from the connecting piece. 0036-06 4.5 4.4 0040-04 the central adjuster is located at the front of the seat, beneath the cover. This secures the central be...
Page 17
4. Adjusting the seat to the child’s size / adjusting the head support and harness 0251-01 then pull the two belts out to the front through the backrest and the seat cover. Now thread both belts from the front through the cover and into the required slot. On the back you must thread both belts back ...
Page 18: Click
4. Adjusting the seat to the child’s size / adjusting the harness / shortening the belts 0252-02 0143-04 0124-03 click 4.8 when does the belt system need to be shortened? If you cannot tighten the child seat belt sufficiently by pulling on the central adjuster at the front of the seat, then it will ...
Page 19
4. Adjusting the seat to the child’s size / shortening the belts 0253-01 remove the seat shell from the base unit and lay the shell upside down on a clean surface. Release the elastic tapes on the cover and pull the cover back a little. Lever out the metal clasps secured on the bottom of the shell, ...
Page 20: Click
Click 4. Adjusting the head support / adjusting the seat to the child’s size 0254-01 when does the shortened belt system need to be returned to its lengthened setting? If, after releasing the child seat belt by means of the central adjuster, it does not pull forwards sufficiently to allow the belt s...
Page 21
1 5. Releasing the belt tensioner to remove the seat 0255-01 releasing the belt tensioner on the base unit when installed facing the front: pull the grey lever on the belt tensioner upwards with the thumb of your left hand until you can push the small grey button upwards (1) until there is no tensio...
Page 22
0256-01 6. Removing the cover / removing the pelvic insert keep pressing the grey lever on the belt tensioner down and pull the car seat belt in the direction of the arrow to unwind it from the ratchet shaft. Continue removing the seat in the reverse order to its installation. To remove the cover, t...
Page 23
6. Removing the cover / removing the pelvic insert 0257-01 lay the seat shell upside down on a clean surface. Lever out the metal clasps secured on the side or bottom of the shell and push them back through their slots as illustrated. Pull the buckle padding away from the belt buckle and thread the ...
Page 24
6. Removing the cover / removing the pelvic insert 0258-00 if the child’s body weight exceeds 8 kg, the factory-fitted pelvic insert should be removed. This is located on the surface of the seat beneath the seat cover. Remove the cover carefully from the seat shell. To fit the cover, proceed in the ...
Page 25
0259-00 30 ° 7. Care instructions removing the seat covers to wash: the cover is composed of two parts which are secured to the seat by means of velcro tape, buttonholes and tapes. Once these ties have been released the two parts of the cover may easily be removed. To fit the covers, proceed in the ...
Page 26
0260-01 you should also tell your passenger how to remove the child in the event of an accident or danger. The belts may only be routed via the points of contact for the belt on the seat and the positions stated in the user instructions. Belts must not be routed in any other way. The lap belts on th...
Page 27
0261-01 the warranty shall commence from the time at which the seat is purchased. The warranty period shall correspond to the legal warranty period for the sale of child seats applicable in the end user’s country. The contents of the warranty shall comprise the remedy of a defect, the supply of a re...
Page 28
0145-06 um die funktionsfähigkeit und sicherheit ihres kinderauto- sitzes auch nach einem austausch von ersatz- und zube- hörteilen zu gewährleisten, bitten wir sie bei bestellungen ihrem fachhändler nachstehende angaben mitzuteilen: to ensure the maximum efficiency of your child car safety seat aft...