1. DL manuals
  2. Conel
  3. Wireless Router
  4. Bivias v2
  5. User Manual

Conel Bivias v2 User Manual

Other manuals for Bivias v2: User Manual
Manual is about: Two modular concept router

Summary of Bivias v2

  • Page 1

    Two modular concept router bivias v2 user’s manual.

  • Page 2

    Used symbols used symbols danger – important notice, which may have an influence on the user’s safety or the function of the device. Attention – notice on possible problems, which can arise in specific cases. Information, notice – information, which contains useful advice or special interest. Gpl li...

  • Page 3

    Contents contents 1 safety instruction 1 2 product disposal instructions 2 3 router description 3 4 contents of package 4 5 router design 5 5.1 router versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5.2 delivery identification . . . . . . . . . . . . . . . . . . . ...

  • Page 4

    Contents 7.3 technical parameters of hspa+ module . . . . . . . . . . . . . . . . . . . . . . 26 7.4 technical parameters of cdma module . . . . . . . . . . . . . . . . . . . . . . 27 7.5 technical parameters of gps . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 7.6 technical parameters ...

  • Page 5

    List of figures list of figures 1 contents of package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 front panels of bivias v2 sl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 example of bivias v2 sl label . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 6

    List of tables list of tables 1 router versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 delivery identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 version of firmware module . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 7

    1. Safety instruction 1. Safety instruction please, observe the following instructions: • the router must be used in compliance with all applicable international and national laws and in compliance with any special restrictions regulating the utilization of the router in prescribed applications and ...

  • Page 8

    2. Product disposal instructions 2. Product disposal instructions the weee (waste electrical and electronic equipment: 2002/96/ec) directive has been introduced to ensure that electrical/electronic products are recycled using the best available recovery techniques to minimize the impact on the envir...

  • Page 9

    3. Router description 3. Router description conel router bivias v2 is equipped with two independent communication modules for wire- less connectivity of various equipments and devices via ethernet interface 10/100 to the inter- net or intranet. Each module can and should use the infrastructure of an...

  • Page 10

    4. Contents of package 4. Contents of package basic delivered set of router includes: • router, • power supply, • crossover utp cable, • up to three external antennas, • clip for the din rail, • installation cd containing instructions, • paper start guide. Figure 1: contents of package the router ca...

  • Page 11

    5. Router design 5. Router design 5.1 router versions bivias v2 router is supplied in the following versions: box sim1 sim2 i/o usb port1 port2 eth bivias v2 ll sl metal bivias v2 lh sl metal bivias v2 lc sl metal bivias v2 hh sl metal bivias v2 hc sl metal table 1: router versions figure 2: front p...

  • Page 12

    5. Router design 5.2 delivery identification trade name type name other bivias v2 ll sl bivias-v2 lte/lte version in the metal box bivias v2 lh sl bivias-v2 lte/hspa+ version in the metal box bivias v2 lc sl bivias-v2 lte/cdma version in the metal box bivias v2 hh sl bivias-v2 hspa+/hspa+ version in...

  • Page 13

    5. Router design 5.4 ordering codes for all specifications with cdma module, order codes are given for the polish operator orange. Another operator can be selected by changing two digits according to table 3 version of firmware module on page 6. Expansion port equipped port ordering code lte/lte wit...

  • Page 14

    5. Router design 5.5 basic dimensions of metal box figure 4: basic dimensions of metal box 5.6 mechanical dimensions and mounting recommendations mounting recommendations: • possibility to be put on a work surface, • din rail with clips ckd2 (elpac clip sl for metal version) are included. For the mo...

  • Page 15

    5. Router design • before mounting a router on sheet-steel we recommend using an external antenna, figure 5: space around antennas • for every cables we recommend to bind the bunch according to the following picture, we recommend for this use: – length of the bunch (combination of power supply and d...

  • Page 16

    5. Router design • sufficient space must be left before individual connectors for handling of cables, figure 7: space in front of connectors • for correct function of the router we recommend to use in the switch-board earth-bonding distribution frame for grounding of power supply of router, data cab...

  • Page 17

    5. Router design 5.7 removing from the din rail default position of ckd2 holder, which is used for mounting the router on a din rail, is shown in the following figure: figure 8: default position of din holder for removing from the din rail it is necessary to lightly push upward the router so that th...

  • Page 18

    5. Router design 5.8 description of the front panel on the front panel is located: caption connector description pwr 2-pin connector for the power supply adapter. Eth rj45 connector for connection into the local computer network. Port1 rj45 connector for expansion port ethernet or switch. Port2 rj45...

  • Page 19

    5. Router design 5.8.1 status indication about router status inform eight led indicators on the front panel and on every port are two led indicators, which inform about port status. Caption color state description m1 green / orange on indicates the activity of the first module (green color). In the ...

  • Page 20

    5. Router design 5.8.2 power connector pwr panel socket 2-pin. Pin number signal mark description 1 vcc(+) positive pole of dc supply voltage (+10 to +30 v dc) 2 gnd(-) negative pole of dc supply voltage table 7: connection of power connector figure 11: power connector power supply for router is req...

  • Page 21

    5. Router design 5.8.3 antenna connector ant1, ant2, div1, div2, gps and wifi both of main antennas and also both of diversity antennas are connected to bivias v2 router using the sma connector on the front panel. There is also available one sma antenna connector using which gps antenna can be conne...

  • Page 22

    5. Router design 5.8.4 sim card reader the sim card reader for 3 v and 1,8 v sim cards is located on the front panel of the router. To initiate the router into operation it is necessary to insert an activated sim card with un- blocked pin in the reader. The sim cards might be of different adjusted a...

  • Page 23

    5. Router design figure 17: ethernet connector attention! Port eth is not poe (power over ethernet) compatible! Ethernet cable plug into the rj45 connector labeled as eth (see figure below). Figure 18: connection of ethernet cable example of the eth router connection: figure 19: example of router co...

  • Page 24

    5. Router design 5.8.6 port1 the port1 is equipped on customer’s request with one of the offered expansion ports: • ethernet • switch (together with port2) description and examples of expansion ports connection can be found in user’s guide for corresponding expansion port. Port1 cable plug into the ...

  • Page 25

    5. Router design port2 cable plug into the rj45 connector labeled as port1 (see figure below). Figure 21: port2 cable connection 5.8.8 usb port panel socket usb-a. Pin signal mark description data flow direction 1 +5 v positive pole of 5 v dc supply voltage 2 usb data - usb data signal – negative po...

  • Page 26

    5. Router design example of connecting devices with serial interface to the usb: figure 23: connection plc to the router example of connecting of usb flash disk to the usb: figure 24: connection flash memory to the router 5.8.9 i/o port panel socket 3pin. Pin signal mark description data flow direct...

  • Page 27

    5. Router design maximum load binary output is 30 v / 100 ma. The constant current supplied by the binary input is 3 ma. Connector i/o cable connect into the i/o connector on the router head and tighten locking screws (see figure below). Figure 26: connection of i/o cable circuit example of a binary...

  • Page 28

    5. Router design 5.8.10 reset it is important to distinguish between reset and reboot the router. Action router behavior invoking events reboot turn off and then turn on router disconnect and connect the power, press the reboot button in the web configuration reset restore default configuration and ...

  • Page 29

    6. First use 6. First use 6.1 connecting the router before first use before you give up the router, it is necessary to connect all components needed for the operation of your applications and the sim card must be inserted (see figure below). The router can not operate without connected antenna, sim ...

  • Page 30

    6. First use 6.2 start the router is set up connecting the power supply to the router. In the default setting the router starts to login automatically to the preset apn. Device on the ethernet port dhcp server will assign addresses. The behavior of the router can be modified by means of the web or t...

  • Page 31

    7. Technical parameters 7. Technical parameters 7.1 technical parameters of router bivias v2 complies with standards en 301 511, v9.0.2, en 301 908-1 & -2 & -13: v5.2.1, en 301 489-1 v1.8.1, en 301 489-7 v1.3.1, en 301 489-24 v1.4.1, en 60950-1: 2006 temperature range function storage -30 ◦ c to +60...

  • Page 32

    7. Technical parameters continued from previous page lte modul umts parameters ps bit rate 384 kbps (dl) / 384 kbps (ul) cs bit rate 64 kbps (dl) / 64 kbps (ul) w-cdma fdd standard gprs/edge parameters bit rate 237 kbps (dl) / 59,2 kbps (ul) gprs multislot class 10, cs 1 to 4 edge multislot class 12...

  • Page 33

    7. Technical parameters 7.4 technical parameters of cdma module cdma modul cdma parameters rev. A: bit rate 3,1 mbps (dl) / 1,8 mbps (ul) rev. B: bit rate 14,7 mbps (dl) / 5,4 mbps (ul) backward compatible with rev.0 transmit power +23,0 dbm ∼ +30,0 dbm supported bands 450mhz (sub band a,b,l) 800mhz...

  • Page 34

    7. Technical parameters 7.6 technical parameters of processor 32b arm mikroprocesor memory 512 mb ddr sdram 128 mb flash 1 mb mram interface serial interface rs232 ethernet interface 10/100 mbit/s usb 2.0 interface table 17: technical parameters of processor 7.7 technical parameters i/o port 32b arm...

  • Page 35

    8. Recommended literature 8. Recommended literature [1] conel: start guide, [2] conel: configuration manual, [7] conel: user’s manual – expansion port eth, [8] conel: user’s manual – expansion port switch, [9] conel: user’s manual – expansion port wifi, [12] conel: application guide – expansion port...

  • Page 36

    9. Possible problems 9. Possible problems some network cards are able to be set in situation, when it is not possible to connect the router. It is possible to solve this problem in the following steps: • hand by selection communication rates 10 mb/s in property network cards, • connect router over s...

  • Page 37

    10. Faq 10. Faq - i can’t get from internet on equipment, which is connected to router and i have nat en- abled. • the device’s gateway has to be configured as the router. - router resets itself, connection on ethernet fails. • it is necessary to use an antenna, which will be situated far from power...

  • Page 38

    10. Faq • the operator doesn’t give out address dns servers and without dns server’s it is impossible to connect to server dyndns.Org. In log system will be this message: – dyndns daemon started – error resolving hostname: no such file or directory – connect to dyndns server failed - ipsec tunnel is...

  • Page 39

    11. Customers support 11. Customers support you can find current information about this product on our website: www.Conel.Cz upkeep-advices: • the sim-card must be handled carefully as with a credit card. Don’t bend, don’t scratch on this and do not expose to static electricity. • during cleaning of...