1. DL manuals
  2. Conel
  3. Wireless Router
  4. ER75i v2 SL
  5. Configuration Manual

Conel ER75i v2 SL Configuration Manual

Other manuals for ER75i v2 SL: User Manual, User Manual
Manual is about: v2 routers

Summary of ER75i v2 SL

  • Page 1

    Configuration manual for v2 routers www.Infopulsas.Lt info@infopulsas.Lt.

  • Page 2: Used Symbols

    Used symbols conel s.R.O., sokolska 71, 562 04 usti nad orlici, czech republic manual issued in cz, 12/15/2011 ii used symbols danger – important notice, which may have an influence on the user’s safety or the function of the device. Attention – notice on possible problems, which can arise in specif...

  • Page 3: Contents

    Contents iii contents 1. Configuration settings over web browser 1 1.1. Secured access to web configuration 2 1.2. Network status 3 1.3. Dhcp status 4 1.4. Gprs/umts status 5 1.5. Ipsec status 7 1.6. Dyndns status 7 1.7. System log 8 1.8. Lan configuration 9 1.9. Vrrp configuration 13 1.10. Gprs con...

  • Page 4: Picture List

    Picture list iv picture list fig. 1: web configuration 1 fig. 2: network status 4 fig. 3: dhcp status 4 fig. 4: gprs status 6 fig. 5: ipsec status 7 fig. 6: dyndns status 7 fig. 7: system log 8 fig. 8: example program syslogd start with the parameter -r 8 fig. 9: topology of example lan configuratio...

  • Page 5

    Picture list v fig. 50: expansion port configuration 53 fig. 51: example of expansion port configuration 1 54 fig. 52: example of expansion port configuration 2 54 fig. 53: usb configuration 56 fig. 54: example of usb port configuration 1 57 fig. 55: example of usb port configuration 2 57 fig. 56: s...

  • Page 6: Table List

    Table list vi table list table 1: description of interface in network status 3 table 2: description of information in network status 3 table 3: dhcp status description 4 table 4: description of gsm information item 5 table 5: description of period 5 table 6: description of gsm statistic 5 table 7: d...

  • Page 7

    Table list vii table 50: at commands for work with sms 46 table 51: expansion port configuration 1 52 table 52: expansion port configuration 2 52 table 53: cd signal description 52 table 54: dtr signal description 53 table 55: usb port configuration 1 55 table 56: usb port configuration 2 55 table 5...

  • Page 8

    Configuration 1 1. Configuration settings over web browser attention! If the sim card is not inserted in the router, then wireless transmissions will not work. The inserted sim card must have activated gprs. Insert the sim card when the router is switched-off. Monitoring of the status, configuration...

  • Page 9

    Configuration 2 after green led starts to blink it is possible to restore initial settings of the router by pressing button rst on front panel. If press button rst, configuration is restored to default and it is reboot (green led will be on). 1.1. Secured access to web configuration to the web confi...

  • Page 10

    Configuration 3 1.2. Network status to view the system information about the router operation, select the network menu item. The upper part of the window displays detailed information about active interfaces: interface description eth0 networks interface ppp0 interface (active connection to gprs/edg...

  • Page 11

    Configuration 4 fig. 2: network status 1.3. Dhcp status information on the activities of the dhcp server can be accessed by selecting the dhcp status. Dhcp status informs about activities dhcp server. The dhcp server provides automatic configuration of devices connected to the network managed router...

  • Page 12

    Configuration 5 1.4. Gprs/umts status the industrial router xr5i v2 is not availability item gprs/umts status. Gprs menu item contains actual information about gprs/umts connections. Item description plmn code of operator cell the cell to which the router is connected channel the channel on which th...

  • Page 13

    Configuration 6 the ppp connection log is in the bottom of window, where are information about the make-up of the ppp connection and problems in establishment. Fig. 4: gprs status.

  • Page 14

    Configuration 7 1.5. Ipsec status information on actual ipsec tunnel state can be called up in option ipsec in the menu. After correct build the ipsec tunnel, status display ipsec sa established (highlighted in red) in ipsec status information. Other information is only internal character. Fig. 5: i...

  • Page 15

    Configuration 8 1.7. System log in case of any problems with connection to gprs it is possible to view the system log by pressing the system log menu item. In the window, are displayed detailed reports from individual applications running in the router. By the help of button save it is possible to s...

  • Page 16

    Configuration 9 1.8. Lan configuration to enter the network configuration, select the lan menu item. Eth network set in primary lan configuration, expansion port eth set in secondary lan configuration. Item description dhcp client • disabled – the router does not allow automatic allocation ip addres...

  • Page 17

    Configuration 10 it is important not to overlap ranges of static allocated ip address with address allocated by the dynamic dhcp. Then risk collision of ip addresses and incorrect function of network. Example of the network interface with dynamic dhcp server: • the range of dynamic allocated address...

  • Page 18

    Configuration 11 example of the network interface with dynamic and static dhcp server: • the range of allocated addresses from 192.168.1.2 to 192.168.1.4. • the address is allocated 10 minutes. • client's with mac address 01:23:45:67:89:ab has ip address 192.168.1.10. • client's with mac address 01:...

  • Page 19

    Configuration 12 example of the network interface with default gateway and dns server: • default gateway ip address is 192.168.1.20 • dns server ip address is 192.168.1.20 fig. 13: topology of example lan configuration 3 fig. 14: example lan configuration 3 192.168.1.3 192.168.1.4 192.168.1.1 eth 19...

  • Page 20

    Configuration 13 1.9. Vrrp configuration to enter the vrrp configuration select the vrrp menu item. Vrrp protocol (virtual router redundancy protocol) is a technique, by which it is possible to forward routing from main router to backup router in the case of the main router failure. If the enable vr...

  • Page 21

    Configuration 14 example of the vrrp protocol: fig. 15: topology of example vrrp configuration fig. 16: example vrrp configuration – main router fig. 17: example vrrp configuration – backup router main router virtual server id 5 host priority 255 192.168.1.1 192.168.1.2 192.168.1.3 backup router vir...

  • Page 22

    Configuration 15 1.10. Gprs configuration the industrial router xr5i v2 is not availability item gprs configuration. To enter the gprs connection configuration select the gprs menu item. 1.10.1. Gprs connection if the create gprs connection option is selected, the modem automatically tries to establ...

  • Page 23

    Configuration 16 if only one sim card is plugged in the router, router switches between the apn. Router with two sim cards switches between sim cards. Correct pin must be filled. For sim cards with two apn’s there will be the same pin for both apn`s. Otherwise the sim card can be blocked by false si...

  • Page 24

    Configuration 17 if the parameter switch to backup sim card when data limit is exceeded (see next) or send sms when datalimit is exceeded (see sms configuration) are not selected the data limit will not count. 1.10.5. Switch between sim cards configuration at the bottom of configuration it is possib...

  • Page 25

    Configuration 18 the following parameters define the time after which the router attempts to go back to the default sim card or apn. Item description initial timeout the first attempt to switch back to the primary sim card or apn shall be made for the time defined in the parameter initial timeout, r...

  • Page 26

    Configuration 19 the changes in settings will apply after pressing the apply button. Fig. 18: gprs configuration.

  • Page 27

    Configuration 20 example of setting controls the ppp connection to the address 8.8.8.8 in the time interval of 60s for primary sim card and to the address www.Google.Com in the time interval 80s for secondary sim card. In the case of traffic on the ppp control pings are not sent, but the traffic on ...

  • Page 28

    Configuration 21 1.11. Pppoe configuration pppoe configuration item is available only on the industrial router xr5i v2. Pppoe for industrial router works in client mode. Router using connection to the pppoe server or pppoe bridge (for example adsl modem). To enter the pppoe configuration select the ...

  • Page 29

    Configuration 22 1.12. Firewall configuration by the help of a firewall it is possible to set ip addresses from which are possible to remotely access the router and internal network connected behind a router. The choice allow remote access only from specified hosts is given for easier configuration ...

  • Page 30

    Configuration 23 example of the firewall configuration: the router has allowed the following access: • from address 171.92.5.45 using any protocol • from address 10.0.2.123 using tcp protocol on any ports • from address 142.2.26.54 using icmp protocol fig. 23: topology of example firewall configurat...

  • Page 31

    Configuration 24 1.13. Nat configuration to enter the network address translation configuration, select the nat menu item. Nat (network address translation / port address translation - pat) is a method of adjusting the network traffic through the router default transcript and/or destination ip addre...

  • Page 32

    Configuration 25 table 25: remote access configuration example of the configuration with one connection equipment on the router: fig. 25: topology of example nat configuration fig. 26: example nat configuration 1 in these configurations it is important to have marked choice of send all remaining inc...

  • Page 33

    Configuration 26 example of the configuration with more connected equipment: fig. 27: topology of example nat configuration fig. 28: example of nat configuration 2 162.209.13.222 192.168.1.2:80 192.168.1.3:80 192.168.1.4:80 ppp0 10.0.0.1 switch 10.0.0.1:81 10.0.0.1:82 10.0.0.1:83.

  • Page 34

    Configuration 27 in this configuration equipment wired behind the router defines the address server ip address. The router replies, while ping on address of sim card. Access on web interface of the equipment behind the router is possible by the help of port forwarding, when behind ip address of sim ...

  • Page 35

    Configuration 28 remote interface ip address ip address of interface local side of tunnel. Ping interval this parameter defines the time period after which router sends a message to opposite side of tunnel, for check the existence of the tunnel. Ping timeout ping timeout waits on message from off-si...

  • Page 36

    Configuration 29 extra options by the help of parameter extra options it is possible to define additional parameters of the openvpn tunnel, for example dhcp options etc. Table 27: openvpn configuration the changes in settings will apply after pressing the apply button. Fig. 30: openvpn tunnel config...

  • Page 37

    Configuration 30 example of the openvpn tunnel configuration: fig. 31: topology of example openvpn configuration openvpn tunnel configuration: configuration a b protocol udp udp udp port 1194 1194 remote ip address 10.0.0.2 10.0.0.1 remote subnet 192.168.2.0 192.168.1.0 remote subnet mask 255.255.25...

  • Page 38

    Configuration 31 1.15. Ipsec tunnel configuration ipsec tunnel configuration can be called up by option ipsec item in the menu. Ipsec tunnel allows protected (encrypted) connection of two networks lan to the one which looks like one homogenous. In the ipsec tunnels configuration window are four rows...

  • Page 39

    Configuration 32 authenticate mode authentication is possible to set by parameter authenticate mode, at choice are following possibilities: • pre-shared key - shared key for both off-side tunnel. • x.509 certificate - pre-shared key sharable key for both parties tunnel ca certificate this certificat...

  • Page 40

    Configuration 33 the changes in settings will apply after pressing the apply button. Fig. 33: ipsec tunnel configuration.

  • Page 41

    Configuration 34 example of the ipsec tunnel configuration: fig. 34: topology of example ipsec configuration ipsec tunnel configuration: configuration a b remote ip address 10.0.0.2 10.0.0.1 remote subnet 192.168.2.0 192.168.1.0 remote subnet mask 255.255.255.0 255.255.255.0 local subnet 192.168.1.0...

  • Page 42

    Configuration 35 1.16. Gre tunnels configuration to enter the gre tunnels configuration, select the gre menu item. The gre tunnel is used for connection of two networks to one that appears as one homogenous. It is possible to configure up to four gre tunnels. In the gre tunnels configuration window ...

  • Page 43

    Configuration 36 fig. 36: gre tunnel configuration example of the gre tunnel configuration: fig. 37: topology of gre tunnel configuration gre tunnel configuration: konfigurace a b remote ip address 10.0.0.2 10.0.0.1 remote subnet 192.168.2.0 192.168.1.0 remote subnet mask 255.255.255.0 255.255.255.0...

  • Page 44

    Configuration 37 1.17. L2tp tunnel configuration to enter the l2tp tunnels configuration, select the l2tp menu item. L2tp tunnel allows protected connection by password of two networks lan to the one which it looks like one homogenous. The tunnels are active after selecting create l2tp tunnel. Item ...

  • Page 45

    Configuration 38 example of the l2tp tunnel configuration: fig. 39: topology of example l2tp tunnel configuration configuration of the l2tp tunnel: konfigurace a b mode l2tp server l2tp client server ip address --- 10.0.0.1 client start ip address 192.168.1.2 --- client end ip address 192.168.1.254 ...

  • Page 46

    Configuration 39 1.18. Dyndns client configuration dyndns client configuration can be called up by option dyndns item in the menu. In the window can be defined a third order domain registered on server www.Dyndns.Org item description hostname third order domain registered on server www.Dyndns.Org us...

  • Page 47

    Configuration 40 1.19. Ntp client configuration ntp client configuration can be called up by option ntp item in the menu. Ntp (network time protocol) allows set the exact time to the router from the servers, which provide the exact time on the network. By parameter enable local ntp service router is...

  • Page 48

    Configuration 41 1.20. Snmp configuration to enter the snmp configuration it is possible with snmp agent ver.1 configuration which sends information about the router, eventually about the status of the expansion port cnt or m-bus. Snmp (simple network management protocol) provides status information...

  • Page 49

    Configuration 42 every monitor value is uniquely identified by the help of number identifier oid - object identifier. For binary input and output the following range of oid is used: oid description .1.3.6.1.4.1.30140.2.3.1.0 binary input bin0 (values 0,1) .1.3.6.1.4.1.30140.2.3.2.0 binary output out...

  • Page 50

    Configuration 43 example of snmp settings and readout: fig. 42: example of snmp configuration fig. 43: example of the mib browser it is important to set the ip address of the snmp agent (router) in field remote snmp agent. After enter the ip address is in a mib tree part is possible show object iden...

  • Page 51

    Configuration 44 1.21. Smtp configuration to enter the smtp it is possible configure smtp (simple mail transfer protocol) client, which is set by sending emails. Item description smtp server address ip or domain address of the mail server. Username name to email account. Password password to email a...

  • Page 52

    Configuration 45 1.22. Sms configuration the industrial router xr5i v2 is not availability item sms configuration. Sms configuration can be called up by option sms item in the menu. Sms configuration defines the options for sending sms messages from the router at different defined events and states ...

  • Page 53

    Configuration 46 it is possible to send controls sms in the form: sms description go online sim 1 switch to sim1 card go online sim 2 switch to sim2 card go online switch router in online mode go offline ppp connection termination set out0=0 set output i/o connector on 0 set out0=1 set output i/o co...

  • Page 54

    Configuration 47 for the text mode for sms writing is used command at+cmgf=1. At+cmgf=1 enter ok the sms message is created by the help of command at+cmgs=. After enter button is pressed is displayed mark >, behind this mark it is possible to write your own sms message. The sms message is sent by th...

  • Page 55

    Configuration 48 after powering up the router, at introduction of the telephone number comes sms in the form of: router (unit id) has been powered up.Gsm signal strength –xx dbm. After ppp connect, at introduction of the telephone number comes sms in the form: router (unit id) has established ppp co...

  • Page 56

    Configuration 49 example of the router configuration for sms sending via serial interface on the port1: fig. 47: example of sms configuration 2.

  • Page 57

    Configuration 50 example of the router configuration for controlling via sms from every phone numbers: fig. 48: example of sms configuration 3.

  • Page 58

    Configuration 51 example of the router configuration for controlling via sms from two phone numbers: fig. 49: example of sms configuration 4.

  • Page 59

    Configuration 52 1.23. Expansion port configuration configuring of the expansion ports port1 and port2 can cause selecting expansion port 1 or expansion port 2. Item description baudrate applied communication speed. Data bits number of data bits. Parity control parity bit • none - will be sent witho...

  • Page 60

    Configuration 53 when you select items use dtr as control of tcp connection is activated function control tcp connection using signal dtr (cd on the router). Dtr description server description client active the router allows establishing a tcp connection. Router starts tcp connection. Nonactive the ...

  • Page 61

    Configuration 54 example of external port configuration: fig. 51: example of expansion port configuration 1 fig. 52: example of expansion port configuration 2 ppp0 10.0.0.1 ppp0 10.0.0.2 settings in the router mode: tcp server server address: - tcp port: 2000 rs232 rs232 pc plc settings in the route...

  • Page 62

    Configuration 55 1.24. Usb port configuration the usb port configuration can be called up by airbrush option usb port in menu. Configuration can be done, if we have usb/rs232 converter. Item description baudrate applied communication speed. Data bits number of data bits. Parity control parity bit • ...

  • Page 63

    Configuration 56 when you select items use dtr as control of tcp connection is activated function control tcp connection using signal dtr (cd on the router). Dtr description server description client active the router allows establishing a tcp connection. Router starts tcp connection. Nonactive the ...

  • Page 64

    Configuration 57 example of usb port configuration: fig. 54: example of usb port configuration 1 fig. 55: example of usb port configuration 2 ppp0 10.0.0.1 ppp0 10.0.0.2 settings in the router mode: tcp server server address: - tcp port: 2000 eth usb/rs232 pc equipment settings in the router mode: t...

  • Page 65

    Configuration 58 1.25. Startup script in the window startup script it is possible to create own scripts which will be executed after all initial scripts. The changes in settings will apply after pressing the apply button. Fig. 56: startup script change take effect after shut down and witch on router...

  • Page 66

    Configuration 59 1.26. Up/down script in the window up/down script it is possible to create own scripts. In the item up scriptis defined scripts, which begins after establishing a ppp/wan connection. In the item down script is defines script, which begins after lost a ppp/wan connection. The changes...

  • Page 67

    Configuration 60 1.27. Automatic update configuration in the window automatic update it is possible to set automatic configuration update. This choice enables that the router automatically downloads the configuration and the newest firmware from the server itself. The configuration and firmware are ...

  • Page 68

    Configuration 61 the following examples find if there is a new firmware or configuration each day at 1:00 in the morning. An example is given on the type of router er75i v2. • firmware: http://router.Cz/er75i-v2.Bin • configuration file: http://router.Cz/temelin.Cfg fig. 60: example of automatic upd...

  • Page 69

    Configuration 62 1.29. Change profile to open the dialog box for changing profile select the change profilemenu item. Profile switch is making by press the button apply. Change take effect after restarting router by the help of button reboot in web administration or by sms message. It is possible se...

  • Page 70

    Configuration 63 1.31. Set real time clock one - shot inner clock of the router setting can be called up in option set real time clock item in the menu. Clocks are set according to the engaged ntp server after push- button operation apply. Fig. 65: set real time clock 1.32. Set sms service center ad...

  • Page 71

    Configuration 64 1.34. Send sms the industrial router xr5i v2 is not availability item send sms. Sending sms messages is possible in menu send sms. The sms message will be sent after entering the phone number and text sms (message) and by pushing button send. Fig. 68: send sms sms message sending vi...

  • Page 72

    Configuration 65 1.37. Update firmware to view the information about the firmware version and instructions for its update select the update firmware menu item. New firmware is selected via browsebutton and update the following pressing the update button. Fig. 70: update firmware after successful fir...

  • Page 73

    Configuration 66 2. Configuration setting over telnet attention! If the sim card isn’t inserted in the router, it is impossible for the router to operate. The included sim card must be activated for gprs transmissions. Monitoring of status, configuration and administration of the router can be perfo...