- DL manuals
- Connect Systems
- Transceiver
- CS1000
- User Manual
Connect Systems CS1000 User Manual
Summary of CS1000
Page 1
Cs1000 and cs1001 users manual fm handheld tranceiver connect systems incorporated 1802 eastman ave,. Suite 116 ventura ca 93003 version 1.00 copyright 2009 by connect systems incorporated.
Page 2
2 guide for those that do not like to read manuals you have seven items in your box as follows: radio battery antenna power supply (wall wart) charger leather case strap setting up the radio 1. Attach the antenna to the radio. 2. Insert the battery into the radio. 3. Insert the cord from the power s...
Page 3: Thank You
3 thank you we are very grateful for you purchasing the connect systems inc. Brand professional two-way radio. This radio incorporates the latest technology and can bring great convenience to your life and work. The quality and function of this radio will meet your demands for reliable communication...
Page 4
4 warning on danger of radio frequency and magnetic energy the model cs1000 generates both radio frequency energy and magnetic energy while transmitting. Any transmitter has the potential to cause heating and other thermal effects in your body. The amount of heating and other thermal effects is dete...
Page 5: Fcc Warnings
5 fcc warnings this equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized ...
Page 6
6 charging the battery insert the cable of the power supply into the power jack at the back of the charger. You can determine it is the power jack because it is the only hole in the charger that will accommodate the cable from the power supply. Insert the power adapter into the applicable ac 110 vol...
Page 7
7 installing the batery align the two protrusions at the lower end of the battery to the slot at the lower part of the shell of the radio and insert in. Press the upper end of the battery down until the push button on the radio is completely bounced out and locked. Removing the battery to remove the...
Page 8
8 danger: things not to do with your battery do not take apart or reconstruct battery pack the battery pack has various safety features and protection circuits to avoid damage to the battery and the user. If these safety features are compromised, the battery may burst in flame, get hot, rupture, or ...
Page 9
9 do not touch a ruptured or leaking battery the battery contains some chemicals that if it gets in your eyes can cause permanent eye damage or even blindness. If the liquid from the battery gets in your eyes, wash out your eyes as soon as possible without rubbing your eyes. Go to the emergency hosp...
Page 10
10 basic operation light emitting diodes your radio has two light emitting diodes, normally called leds. The meaning of the colors and if it is on solid or flashing is described below. Red led solid: the radio is transmitting. This can be caused by you pressing the ptt switch on the side of the radi...
Page 11
11 channel turn the channel selector knob to select the desired channel. The built in voice prompt if enabled will tell you what channel you are on. If you are on the correct channel and that channel is set to receive ctcss or dcs code and there is a radio transmitting on that channel and that trans...
Page 12
12 programmable function keys there are three buttons on the radio that are programmable for different functions. Each button has the capability of having two separate functions, determined by how long the button is pressed. The length of time the button has to be pressed for the second feature is d...
Page 13
13 4. Call key 2 pressing this key sends either a preprogrammed dtmf code or two tone code. This is a paging feature that is used to contact individual radio or sometimes to set off certain type of alarming features. When you set it for a dtmf code or a two tone code the other radio has to be able t...
Page 14
14 9. Scan this is an alternate action switch. Pressing the key the first time starts the scan and pressing it again stops the scan. The purpose of the scan function is to allow the user to monitor multiple channels and stop at the channel that is active. This would be useful for a supervisor who ne...
Page 15
15 10. Nuisance delete pressing this key deletes the current channel that has activity. If the radio is scanning and is not stopped at a channel then this key does nothing. The purpose of this key is to delete scan channels that have noise on them or other erroneous transmissions. This prevents the ...
Page 16
16 15. Squelch on/off this is an alternative action switch that when enabled will disable the squelch and allow the user to hear a very weak signal. When this switch is disabled, the squelch is enabled and will prevent the user from hearing noisy signals. This feature should only be used if the user...