- DL manuals
- Connect Systems
- Transceiver
- CS4000
- User Manual
Connect Systems CS4000 User Manual
Summary of CS4000
Page 1
Cs4000 and cs4001 users manual fm handheld tranceiver connect systems incorporated 1802 eastman ave., suite 116 ventura ca 93003 version 1.00 copyright 2010 by connect systems incorporated.
Page 2
2 guide for those that do not like to read manuals you have eight items in your box as follows: radio fixed bracket power cable hand microphone microphone hanger m4*10 combination screw (quantity 4) m4*16 self-tapping screw (quantity 2) m5*16 self-tapping screw (quantity 4) fixed bracket power cable...
Page 3: Thank You
3 thank you we are very grateful for you purchasing the connect systems inc. Brand professional two-way radio. This radio incorporates the latest technology and can bring great convenience to your life and work. The quality and function of this radio will meet your demands for reliable communication...
Page 4
4 warning on danger of radio frequency and magnetic energy the model cs4000 and cs4001 generates both radio frequency energy and magnetic energy while transmitting. Any transmitter has the potential to cause heating and other thermal effects in your body. The amount of heating and other thermal effe...
Page 5: Fcc Warnings
5 fcc warnings this equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized ...
Page 6
6 instructions for the radio technician connection of power cable check whether there is a hole for the power cable on the insulating board. If not, bore the board with the suitable drill bit and fix a rubber grommet on it. Have the cable pass through the insulating board into the car engine. Connec...
Page 7: Radio Overview
7 radio overview front panel ⑾ （ 1） power button press this button for a long time (more than 1.5 seconds) to start or close the radio. （ ） 2 led indicator the red indicator will light when it transmitting. The green indicator will light when it receiving. The indicator will flicker and give an oran...
Page 8
8 display screen display description it means the receiving signal strength. 4 lines mean the strongest signal. Transmission power level ”l” means the transmission of signal for the radio at the lower power; ”m” means the transmission of signal for the radio at the medium power; ”h” means the transm...
Page 9
9 basic operation 1. Startup: press the red power button for at least 1.5 seconds to start or close the radio. 2. Volume press the “monitor” or “squelch” button to listen to the background noise first, and then adjust the volume by turning the volume control knob. Turning the volume knob to the righ...
Page 10
10 programmable keys , ， ， ， ， can be programmed for one of the auxiliary functions. Each key can take on double duty by defining the length of time the key has to be pressed to utilize the extra function. As an example, p2 can be programmed to select the power output if its pressed for less than 1 ...
Page 11
11 every time the key is pressed the previous zone is accessed. Zone 0 allows all channels to be accessed. The other zones can access up to 16 channels. Display channel frequency this is an alternate action key that will change the mode of display between channel frequency and channel name display c...
Page 12
12 scan lists where the user programmable field has been enabled. When the scan mode is enabled the display will say “scan” in large characters in the bottom middle of the display. The purpose of the scan function is to allow the user to monitor multiple channels and stop at the channel that is acti...
Page 13
13 channels. If a single channel has been preprogrammed, then pressing the key will select the preprogrammed channel. If the dealer has preprogrammed two channels, then pressing the key will alternate between the two preprogrammed channels. The display will show the channel selected. Talk around thi...
Page 14
14 while the key is pressed, the display will show mon on the second line of the display. This key will also cancel the current incoming call. Normally the user will only hear messages with the proper ctcss or dcs codes. This is to prevent the user from fatigue by hearing all messages sent to everyb...
Page 15
15 squelch/call cancel this is an alternative action key that enables or disables the squelch mode. While in the squelch mode, any voice traffic will be heard no matter what the squelch level. That means if there is no signal you will hear squelch noise. While the key is pressed, the display will sh...
Page 16
16 radio call the radio call key is a multifunction key that has the ability to generate selective calls, call alerts, radio check, kill, and active. The exact function(s) allowed is determined by the dealer. Call 1 when the “call 1” key is pressed, a preprogrammed two tone, dtmf, or mdc page will b...
Page 17
17 paging. Call 4 when the “call 4” key is pressed, a preprogrammed two tone, dtmf, or mdc page will be sent. If the dealer programmed the radio for side tone, the two tone, dtmf, or mdc page will be heard as it is being transmitted. This is a paging feature that is used to contact individual radio ...
Page 18
18 depending how the unit is preprogrammed. If the user does not press the appropriate key soon after the radio starts to alarm, the radio will go into an emergency mode and depending on the dealer programming, will either generate a local alarm or transmit an alarm to another radio or both. In/out ...
Page 19
19 changing the parameters from the keypad send selective call a. Press “menu selection/enter” button to enter the menu mode. B. Press / button until “radiocal”. C. Press button to select “sel call”. D. Press / button until the required call list appears. E. Press “ptt” button to send the selective ...
Page 20
20 b. Press / button until “rptrtalk”. C. Press button for selection. D. Press / button until “repeate” or “talkrnd”. E. Press button for confirmation. Switch the talkaround or repeater mode through “talkaround”. Miscellaneous items the miscellaneous items can help you customize some setups of the r...
Page 21
21 a. Press the “menu selection/enter” button to enter the menu mode. B. Press / button until “sys scan”. C. Press button for selection. D. Press / button until “scan on?” or “scan of?” e. Press button for confirmation. Use the scan button a. Press “scan” button to activate the scan function. B. Pre...
Page 22
22 c. Press button to select quitting. Note: ¾ where the ost backup function is selected, the radio will save the ost code of each channel even if the channel is changed or the machine is shut down. ¾ in the ost state, the lcd of the vehicle mounted radio and p2 icon will display. ¾ in the ost state...