1. DL manuals
  2. Connect Tech
  3. Network Card
  4. Titan/cPCI
  5. User Manual

Connect Tech Titan/cPCI User Manual

Manual is about: CompactPCI Serial Communications

Summary of Titan/cPCI

  • Page 1

    Titan/cpci compactpci serial communications user manual connect tech inc 42 arrow road guelph, ontario n1k 1s6 tel: 519-836-1291 toll: 800-426-8979 (north america only) fax: 519-836-4878 email: sales@connecttech.Com support@connecttech.Com url: www.Connecttech.Com ctim-00009, revision 1.01 february ...

  • Page 2

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 ii limited lifetime warranty connect tech inc. Provides a lifetime warranty for all connect tech inc. Products. Should this product, in connect tech inc.'s opinion, fail to be in good working order during the warranty period, connect tech inc...

  • Page 3

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 iii certification statements class a computing device titan/cpci; titan/cpci rear i/o; titan/cpci rear i/o opto* fcc this equipment complies with the requirements in part 15 of fcc rules for a class a computing device. Operation of this equip...

  • Page 4

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 iv table of contents limited lifetime warranty ................................................................................................................. Ii copyright notice ................................................................

  • Page 5

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 v list of tables table 1: db-9 cable connector pinouts..........................................................................................................14 table 2: db-37 cable connector pinouts............................................

  • Page 6

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 1 introduction connect tech’s titan/cpci and titan/cpci rear i/o adapters are high performance multi-port serial adapters that allow you to connect up to 4 serial devices through one expansion slot. Titan/cpci adapters provide the high-speed ...

  • Page 7

    Titan/cpci user’s manual, connect tech inc. 2 revision 1.01 customer support overview if you experience difficulties after reading the manual and/or using the product, contact the connect tech reseller from which you purchased the product. In most cases the reseller can help you with product install...

  • Page 8

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 3 titan/cpci installation overview there are two main stages in the installation process for your titan/cpci product: 1. Hardware installation this involves the physical connection of the titan/cpci hardware to your system. 2. Software instal...

  • Page 9

    Titan/cpci user’s manual, connect tech inc. 4 revision 1.01 titan/cpci adapter 2 port model rear i/o connector compactpci bus connector pci 954 quad uart db-9 connector port 2 ejector handle line termination/bias jumper blocks jc, jd ½ duplex control jumper block ja rs-232 select jumper block jb db-...

  • Page 10

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 5 figure 2: titan/cpci model tn004 for compatibility with 64 bit systems titan/cpci tn003 adapter (front panel leds) rear i/o connector compactpci bus connector pci 954 quad uart tx/rx leds ejector handle jumper blocks jc, jd, je, jf ½ duplex...

  • Page 11

    Titan/cpci user’s manual, connect tech inc. 6 revision 1.01 figure 4: titan/cpci rear i/o two and four port adapters j1 j2 j4 titan/cpci rear i/o 2 port model j1 j2 j3 ejector handle db-37 connector ejector handle rear i/o connector rear i/o connector db-9 connector port 2 db-9 connector port 1 tita...

  • Page 12

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 7 figure 5: titan/cpci rear i/o opto two and four port adapters. Ejector handle ejector handle rear i/o connector rear i/o connector titan/cpci rear i/o opto 2 port model titan/cpci rear i/o opto 4 port model rj-45 connector port 2 rj-45 conn...

  • Page 13

    Titan/cpci user’s manual, connect tech inc. 8 revision 1.01 you can combine different titan/cpci and titan/cpci rear i/o adapters in a single computer to accommodate both small and large multi-channel applications. The figure below represents a sample configuration for a system requiring 10 ports. H...

  • Page 14

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 9 installing the titan/cpci adapter in your system titan/cpci and rear i/o adapters to install your titan/cpci or rear i/o adapter in your computer follow these steps: 1. Turn off the power to your computer. 2. Remove the titan from its packa...

  • Page 15

    Titan/cpci user’s manual, connect tech inc. 10 revision 1.01 configuring the titan/cpci compact peripheral component interconnect (cpci) bus architecture offers a feature called plug and play (sometimes referred to as pnp). This feature automatically identifies and configures installed devices each ...

  • Page 16

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 11 multi-drop slave mode in this mode the txd line driver is enabled only when data is transmitted and rxd is enabled all the time. This mode is typically used in multi-drop "4 wire" connections. Please refer to appendix d: rs-422/485 line in...

  • Page 17

    Titan/cpci user’s manual, connect tech inc. 12 revision 1.01 appendix a: specifications operating environment storage temperature: -65 ° c to 150° c operating temperature: 5 ° c to 70° c relative humidity: 5 - 95% non-condensing air movement: no requirement altitude: 15,000 feet (5000 meters) power ...

  • Page 18

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 13 surge suppression transguard transient voltage suppression, able to withstand multiple strikes on every signal of every port. Transient energy dissipation 0.1 joules on every signal of every port transient peak current dissipation 40a on e...

  • Page 19

    Titan/cpci user’s manual, connect tech inc. 14 revision 1.01 appendix b: connectors/pinouts connector pinouts tables 1 and 2 outline the pinouts for the titan/cpci and titan/cpci rear i/o connectors or cable connectors. Technical tip: please ensure that you terminate signals if your application does...

  • Page 20

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 15 table 2: db-37 cable connector pinouts pin no. Port no. Rs-232 signal direction rs-422/485 signal direction 1 1 sg signal gnd sr signal ref 2 1 dtr output txd- output 3 1 txd output txd+ output 4 1 rxd input rxd- input 5 1 dcd input rxd+ i...

  • Page 21

    Titan/cpci user’s manual, connect tech inc. 16 revision 1.01 table 3: rj-45 pinouts – titan/cpci rear i/o opto rj-45 pin no. Db-9 pin cabrj4509 rs- 232 signal direction rs-422/485 signal direction 1 9 n/c no connect rts (-) output 2 1 n/c input rxd (+) input 3 7 rts output rts (+) output 4 5 sg sign...

  • Page 22

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 17 appendix c: factory settings titan/cpci adapters function factory setting electrical interface jumper block jb is set for all ports rs-422/485 - all positions not jumpered half duplex (2 wire) jumper block ja is set for all ports running i...

  • Page 23

    Titan/cpci user’s manual, connect tech inc. 18 revision 1.01 titan/cpci rear i/o opto adapters function factory setting electrical interface jumper blocks ja, jb, jc, jd are set for all ports rs-422/485 – positions 1 not jumpered half duplex (2 wire) jumper blocks ja, jb, jc, jd are set for all port...

  • Page 24

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 19 appendix d: rs-422/485 line interface titan/cpci adapters electrical interface selection the titan/cpci adapter provides jumper selectable rs-232 and rs-422/485 electrical interfaces on each port. Jumper block jb sets the electrical interf...

  • Page 25

    Titan/cpci user’s manual, connect tech inc. 20 revision 1.01 full duplex mode (4 wire) by not installing pins on jumper block ja and by using features in our driver software, you can run the individual rs-422/485 ports in full duplex mode. This mode is typically used in point to point rs-422/485 sit...

  • Page 26

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 21 line termination you can use jumper blocks jc, jd, je and jf to terminate and bias txd ±, rxd ±, rts ±, and cts ± on the individual rs-422/485 ports through jumper selectable 150 Ω fixed resistors. Please refer to figure 7 for a partial sc...

  • Page 27

    Titan/cpci user’s manual, connect tech inc. 22 revision 1.01 example the following example shows the settings on jc, jd, je and jf where rs-422/485 port 1 is terminated on rts ± and txd ±, the rs-422/485 port 2 is set for bias/termination on rts ±, txd ±, cts ±, and rxd ±, the rs-422/485 port 3 is n...

  • Page 28

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 23 titan/cpci rear i/o opto 2 and 4 port adapters • the four port rear i/o opto requires a four port front i/o titan to be installed. • the two port rear i/o opto requires a two port front i/o titan to be installed. • in either case, when usi...

  • Page 29

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 25 titan/cpci rear i/o opto electrical interface selection the titan/cpci rear i/o opto adapter provides jumper selectable rs-232 and rs-422/485 electrical interfaces on each port. Jumper blocks ja, jb, jc, jd set the electrical interfaces fo...

  • Page 30

    Titan/cpci user’s manual, connect tech inc. 26 revision 1.01 full duplex mode (4 wire) ensure j1 and j2 for the specific port is removed. You must also ensure that the configuration software does not have the ½ duplex or multi-drop slave mode enabled. Half duplex rs-422/485 (2 wire) ensure j1 for th...

  • Page 31

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 27 txd txd + rxd - txd - rxd + titan/cpci rear i/o opto rs-422/485 line bias/termination rxd rts rts + cts - rts - cts + cts pci 954 uart 150 Ω 1.8k Ω 1.8k Ω +5 v 150 Ω 1.8k Ω 1.8k Ω +5 v 150 Ω ja4, jb4, jc4, jd4 150 Ω ja3, jb3, jc3, jd3 ja8,...

  • Page 32

    Titan/cpci user’s manual, connect tech inc. 28 revision 1.01 example the following example shows the settings on ja, jb, jc and jd where port 1 is terminated on rts ± and txd ±, the rs-422/485 port 2 is set for bias/termination on rts ±, txd ±, cts ±, and rxd ±, the rs-422/485 port 3 is not terminat...

  • Page 33

    Titan/cpci user’s manual, connect tech inc. Revision 1.01 29 rs-422/485 cable wiring you can wire titan/cpci adapters in various ways to communicate with rs-422/485 peripherals. This section describes a few examples of rs-422/485 cabling schemes. Figure 8 depicts a 4 wire cabling scheme between a po...

  • Page 34

    Titan/cpci user’s manual, connect tech inc. 30 revision 1.01 figure 9 depicts a 2 wire cabling scheme between a port on the titan/cpci adapter to a port on the rs-422/485 peripheral. Figure 10: rs-422/485 wiring diagram (2 wire) rts + rts - cts + cts - txd + txd - rxd + rxd - rxd + txd + rxd - txd -...