1. DL manuals
  2. ConnectGear
  3. Computer Hardware
  4. GA-H03D
  5. User Manual

ConnectGear GA-H03D User Manual

Other manuals for GA-H03D: User Manual
Manual is about: CardBus 10/100 Fast Ethernet PC Card

Summary of GA-H03D

  • Page 1

    122401-01 cardbus 10/100 fast ethernet pc card user manual.

  • Page 2: Regulatory Statements

    Regulatory statements fcc certification the united states federal communication commission (fcc) and the canadian department of communications have established certain rules governing the use of modems and other electronic equipment. Fcc part 15 registration this device complies with part 15 of fcc ...

  • Page 3: Table of Contents

    Table of contents introduction............................................. 1 s ystem r equirements .................................. 1 operating systems....................................... 1 introduction to cardbus.................. 2 hardware installation ..................... 4 inserting the ...

  • Page 4: Introduction

    - 1 - introduction system requirements ƒ an ibm compatible notebook computer with 486 or faster processor with cardbus supported socket. ƒ drivers and utilities provided with this product ƒ pcmcia pc card compliant card services and socket services ƒ 100base-tx fast ethernet or 10baset ethernet conn...

  • Page 5: Introduction to Cardbus

    - 2 - introduction to cardbus cardbus is the next generation 32-bit version issued by pcmcia pc card standard. In addition to support a wider bus (32 bits instead of 16 bits), cardbus also supports bus mastering and operation speeds up to 33 mhz. The 132mbytes bus transfer rate (compares with legacy...

  • Page 6: Or Auto_Detect Mode.

    - 3 - ƒ due to variant design of notebook computers, some models implement a setting in the computer’s bios to switch between cardbus and 16-bit pc card modes. You could consult the user’s guide of your notebook and properly set on the cardbus or auto_detect mode..

  • Page 7: Hardware Installation

    - 4 - hardware installation inserting the cardbus dual-speed pc card 1. Hold the cardbus pc card with wide connector toward the slot and the brand label facing upward. 2. Insert the cardbus pc card and push it firmly into the bottom. (please see the figure on the next page for reference) removing th...

  • Page 8: Connecting to The Network

    - 5 - connecting to the network connect rj-45 port of the cardbus 10/100 ethernet pc card adapter to the category 5 network cable before loading any network driver. ƒ for operation in the 100mbps (100base-tx) ethernet network, a category 5 unshielded twisted pair (utp) cable should be used to connec...

  • Page 9

    - 6 - 4. Act led indicator: blinks orange when the cardbus 10/100 ethernet attached port pc card adapter is transmitting/receiving data..

  • Page 10: Software Installation

    - 7 - software installation installation for windows 95 (osr2) 1. Start windows. Make sure the cardbus 10/100 fast ethernet pc card is well connected to the cardbus socket. 2. Click next on update device drivers wizard. 3. Click the others locations button. 4. Insert driver diskette into the floppy ...

  • Page 11: Installation For Windows 98

    - 8 - installation for windows 98 1. When the pc card is well inserted into the pc card slot in your computer, the following picture will appear automatically and prompt you to insert the new device driver. Click next to proceed. 2. Select search for the best driver for your device (recommended) and...

  • Page 12

    - 9 - 4. Windows has found the appropriate driver for the new device. Click next to install. 5. Click finish. The pc card driver installation will be successfully completed..

  • Page 13

    - 10 - 6. Click yes to restart your computer. Installation for windows 2000 1. When the pc card is well inserted into the pc card slot in your computer, the following picture will be appeared on the screen automatically. Click next to proceed..

  • Page 14

    - 11 - 2. Select search for a suitable driver for my device (recommended) and click next. 3. Insert the new device driver to the disk drive and click next. Windows will start searching for the appropriate driver for the pc card. 4. Wait for a while until windows has found the appropriate driver..

  • Page 15

    - 12 - 5. Click yes to continue. 6. Click finish. The pc card driver installation is successfully completed..

  • Page 16: Installation For Window Me

    - 13 - installation for window me 1. Once the pc cardis well connected to your computer, windows me will automatically detect the new device. Select specify the location of the driver… and click next. 2. Insert the device driver disk into the floppy disk drive on your system. Select removable media ...

  • Page 17: Click Next To Continue.

    - 14 - 3. Click next to continue. 4. Windows will copy the appropriate driver to your system. If windows me asks you to supply your original windows me installation cd-rom, load it on the cd- rom drive. 5. Click finish to complete the software installation..

  • Page 18: Installation For Windows Xp

    - 15 - installation for windows xp 1. Once the device is well connected, windows will detect the new device and prompt you to insert the network device driver. Click install from a list or specific location… and click next. 2. Insert the device driver disk into the floppy disk drive of your system. ...

  • Page 19: Continue Anyway To Proceed.

    - 16 - 3. Windows will start searching for the appropriate driver for the installation. When the screen appears as below, click continue anyway to proceed. 4. Wait for seconds while windows copies the appropriate driver to your system. 5. Click finish. The software installation for this network devi...

  • Page 20

    - 17 - installation for novell netware 1. At the dos prompt type start under the path etware. 2. The installation program will automatically proceed. 3. Follow novell's instructions on using odi programs. 4. Enter login at the netware login prompt, e.G. F:login>. 5. Type your user name and passwor...

  • Page 21: Specifications

    - 18 - specifications network interface specifications: ƒ 10mbps ethernet:ieee 802.3 standard 10baset baseband csma/cd local area network. ƒ 100mbps ethernet:ieee 802.3u standard 100base-tx baseband csma/cd local area network. ƒ 20/200mbps full duplex support ƒ autonegotiation between all four opera...