Summary of Vi10P
Page 1
V vi7p/vi10p manual 1.1 en.
Page 2
S y m b o l s o n t h e p r o d u c t p l e a s e r e f e r t o t h e i n f o r m a t i o n i n t h e m a n u a l . W a r n i n g ! D a n g e r o u s v o l t a g e ! General information vi7p/vi10p manual version: 1.1 en, 08/2015, d2724.En .01 copyright © 2015 by d&b audiotechnik gmbh; all rights res...
Page 3
1. Safety precautions........................................................... 4 1.1. Information regarding the use of loudspeakers.................... 4 2. Vi7p/vi10p loudspeaker.............................................. 5 2.1. Product description.................................................
Page 4
1.1. Information regarding the use of loudspeakers potential risk of personal injury never stand in the immediate vicinity of loudspeakers driven at a high level. Professional loudspeaker systems are capable of causing a sound pressure level detrimental to human health. Seemingly non-critical sound ...
Page 5
2.1. Product description vi7p/vi10p are passive 3-way loudspeakers housing two 10" lf drivers, one horn-loaded 8" mf driver and a 1.4" hf compression driver with a rotatable cd horn producing a nominal dispersion (h x v) of 75° x 40° (vi7p) or 110° x 40° (vi10p), respectively. All components are arr...
Page 6
Fixed cable connection the vi7p and vi10p loudspeakers are each supplied with a cover plate [1] and a rubber grommet feed through [2]. For indoor operation, these items can be used to hide the connector panel, if required. For unprotected outdoor operation, the connector panel must be covered, i.E. ...
Page 7
Nl4 connection with cover plate the two nl4 connector sockets of the cabinet's connector panel are located in a recess to allow the use of the cover plate [1] together with nl4 cable connectors, as shown in the graphic opposite. Note: neutrik nl4fc type connectors must be used for this option. The c...
Page 8
Hfa circuit in hfa mode (high frequency attenuation), the hf response of the system is rolled off. Hfa provides a natural, balanced frequency response when a unit is placed close to listeners in near field or delay use. High frequency attenuation begins gradually at 1 khz, dropping by approximately ...
Page 9
2.4. Dispersion characteristics the following graphs show dispersion angle over frequency of a single cabinet plotted using lines of equal sound pressure (isobars) at –6 db and –12 db. Isobar diagram horizontal vi7p vertical setup isobar diagram vertical isobar diagram horizontal vi7p horizontal set...
Page 10
Isobar diagram horizontal vi10p vertical setup isobar diagram vertical isobar diagram horizontal vi10p horizontal setup, horn rotated isobar diagram vertical d&b vi7p/vi10p manual 1.1 en 10
Page 11
Altering the hf horn dispersion by factory default, the hf horn is fitted to the cabinet providing the nominal horizontal dispersion when the cabinet is used in upright position. This is indicated by a white label on the horn flange. The label is visible through the front grill on each side of the c...
Page 12
2.5. Technical specifications vi7p/vi10p system data frequency response (–5 db standard) 59 hz - 18 khz frequency response (–5 db cut mode) 100 hz - 18 khz max. Sound pressure (1 m, free field) vi7p with d12/d20/30d 139 db vi7p with d80 142 db vi10p with d12/d20/30d 138 db vi10p with d80 141 db (spl...
Page 13
Vi7p/vi10p cabinet dimensions in mm [inch] d&b vi7p/vi10p manual 1.1 en 13.
Page 14
3.1. Eu conformity of loudspeakers (ce symbol) this declaration applies to: d&b vi7p loudspeaker, z0724 d&b vi10p loudspeaker, z0725 manufactured by d&b audiotechnik gmbh. All production versions of these types are included, provided they correspond to the original technical version and have not bee...
Page 16
D2724.En .01, 08/2015 © d&b audiotechnik gmbh www.Dbaudio.Com.