Summary of Minikote EZ G3
Page 1
Owners manual minikote ez 652792 laminator.Com www.Laminator.Com.
Page 2
Contents section index speci¿ cations ...........................................................................................................................1 important safeguards ...............................................................................................................2 gen...
Page 3
Specifications height .................................................................................. 15” width ................................................................................... 34” depth (with feed tray ) ......................................................... 20” net weight ...
Page 4
Important safeguards 2 • read all the safety and operating instructions before connecting or using this unit. • retain this notice and the owners manual for future reference. • adhere to all warnings and operating instructions. • do not use this unit near water (e.G. Near a bathtub, etc.) • the wear...
Page 5
General diagrams 3 a b c the minikote ez, offers a reverse feature. They are designed to laminate a variety of materials using up to 27” laminating ¿ lm. The minikote ez is capable of lamination from 1 to 9 feet per minute and can be reversed by the push of a button. Tension adjusting knobs (l) are ...
Page 6
General diagrams 4 d e j g h k l i f n m laminator.Com www.Laminator.Com.
Page 7
5 i. Unpacking i. Unpacking remove the laminator from its box by grasping the housings and pulling up. Do not use rollers or shafts as handles - this could cause damage. Choose a location for the laminator that is clean, well-lit and draft free. Make sure it is not in the path of any fans, room air ...
Page 8
6 b. Loading film: 1” mandrel (k) b. Loading film: 1” mandrel (k) unpack the upper and lower supply man- drels. The upper and lower mandrels are different. The word “top” is stamped on the shaft of the upper mandrel and the word “low” is stamped on the shaft of the lower mandrel. The ends of each ma...
Page 9
C. Threading the film c. Threading the film remove the feed tray and the heatguard. Thread the ¿ lm as shown in the ¿ gure on the right. Pull the ¿ lm around the idler rollers as shown. Do not mistake the reinforcing bar for the do not mistake the reinforcing bar for the idler roller idler roller. M...
Page 10
8 d. Laminating d. Laminating after the machine is loaded with ¿ lm (see b. Loading film: 1” mandrel) and threaded (see c. Threading the film), it is ready to laminate. Ensure that the laminator has reached the preset temperature. This will be indicated by the ready light being illu- minated. Place ...
Page 11
Note note: as the diameter of the ¿ lm roll decreases, tension should be reduced. To increase tension, turn the adjusting knob clockwise. To decrease tension, turn the knob counterclock- wise. If the tension is not equal top and bottom, the laminated product will curl. If the material curls up up as...
Page 12
B. Speci¿ c troubleshooting guide b. Speci¿ c troubleshooting guide c. Removing a “wrap-around” c. Removing a “wrap-around” a “wrap-around” occurs if the ¿ lm exiting the rear rollers curls around one of them causing the laminate to wind around the roller. If the wrap-around is not severe, simply us...
Page 13
Shut the machine off! Shut the machine off! Minikote ezs have set screws at both ends of each laminating and pull roller. With the use of a 3/32 hex key, loosen all four set screws on the pull rollers. Cut the plastic between the lami- nating and pull rollers, grab the loose end and pull. The roller...
Page 14
Exploded view 12 le ft s id e p a n e l el ec t r o n ic s ex p lo d ed v iew laminator.Com www.Laminator.Com.
Page 15
Limited warranty dealer, warrants to the original consumer purchaser that each new minikote ez laminator which proves defective in materials or workmanship within the applicable warranty period will be repaired or, at our option, replaced without charge upon its return as outlined below. The applica...