1. DL manuals
  2. D-Link
  3. Switch
  4. 3100 24 - DGS Switch - Stackable
  5. User Manual

D-Link 3100 24 - DGS Switch - Stackable User Manual

Manual is about: D-Link Systems Switch User Manual

Summary of 3100 24 - DGS Switch - Stackable

  • Page 1

    D-link™ dgs-3100 series gigabit stackable managed switch user manual v2.20

  • Page 2

    Information in this document is subject to change without notice. © 2007 d-link computer corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of d-link computer corporation is strictly forbidden. Trademarks used in this text: d-link and the d-link lo...

  • Page 3: Table of Contents

    Table of contents preface..................................................................................................................................................................I system overview ..................................................................................................

  • Page 4

    Defining snmp host table ............................................................................................................................................ 47 defining snmp engine id ..............................................................................................................

  • Page 5

    Configuring port security ................................................................................................................................................... 97 configuring guest vlans ......................................................................................................

  • Page 6: Preface

    Dgs-3100 series gigabit stackable managed switch user manual i preface this preface provides an overview to the guide, and includes the following sections: • system overview • viewing the device • device management methods • user guide overview • intended audience • notes, notices, and cautions • sa...

  • Page 7: System Overview

    Dgs-3100 series gigabit stackable managed switch user manual system overview the dgs-3100 series and the dgs-3100-24tg gigabit ethernet switches enhance networks by providing a powerful switch that eliminates network bottlenecks, enabling network administrators to fine tune network configurations. T...

  • Page 8: Device Management Methods

    Dgs-3100 series gigabit stackable managed switch user manual iii device management methods the dgs-3100 series and dgs-3100-24tg provide different methods for managing the device including: • web based management interface • snmp-based management • command line console web based management interface...

  • Page 9: User Guide Overview

    Dgs-3100 series gigabit stackable managed switch user manual user guide overview this section provides an overview to the dgs-3100 series and the dgs-3100-24tg switch manual, including the guide structure and a chapter overview: • section 1, getting started — provides general background for understa...

  • Page 10

    Dgs-3100 series gigabit stackable managed switch user manual v • do not service any product except as explained in your system documentation. Opening or removing covers that are marked with the triangular symbol with a lightning bolt may expose you to electrical shock. Only a trained service technic...

  • Page 11

    Dgs-3100 series gigabit stackable managed switch user manual move products with care; ensure that all casters and/or stabilizers are firmly connected to the system. Avoid sudden stops and uneven surfaces. General precautions for rack-mountable products observe the following precautions for rack stab...

  • Page 12

    Dgs-3100 series gigabit stackable managed switch user manual protecting against electrostatic discharge static electricity can harm delicate components inside your system. To prevent static damage, discharge static electricity from your body before you touch any of the electronic components, such as...

  • Page 13: Getting Started

    Dgs-3100 series gigabit stackable managed switch user manual 1 getting started to begin managing the device, simply run the browser installed on the management station and point it to the ip address defined for the device. For example; http://123.123.123.123. Please note that the proxy for session c...

  • Page 14

    Dgs-3100 series gigabit stackable managed switch user manual figure 1-1. Device information page the following table describes the main 6 areas on the device information page: view description 1. Tree view select the folder or window to be displayed. The folder icons can be opened to display the hyp...

  • Page 15: Using The Tool Menu

    Dgs-3100 series gigabit stackable managed switch user manual using the tool menu the tool menu contains menu options for: • displaying the stack status • locating devices • backing up and restoring configuration files • resetting the device • downloading the firmware • rebooting the system displayin...

  • Page 16

    Dgs-3100 series gigabit stackable managed switch user manual backing up and restoring configuration files the config backup and restore page contains fields for downloading and uploading the configuration file from the device through http or tftp server. To back up and restore configuration files: 1...

  • Page 17: Resetting The Device

    Dgs-3100 series gigabit stackable managed switch user manual resetting the device the factory reset page restores the factory defaults. To restore the device to the factory default settings: 1. Click > reset. The factory reset page opens: figure 1-4 factory reset page 2. Click . The factory default ...

  • Page 18: Downloading The Firmware

    Dgs-3100 series gigabit stackable managed switch user manual downloading the firmware the ‘firmware download’ web page is used to download the firmware files that will be used to manage the device. Note: firmware version 1.X.X supports 4 skus od dgs-3100 series: dgs-3100-24, dgs-3100- 24p, dgs-3100-...

  • Page 19

    Dgs-3100 series gigabit stackable managed switch user manual the firmware download page contains the following fields: field description http download indicates that the firmware file is downloaded via an http server. Unit — indicates if the firmware file is downloaded to a specific stacking member ...

  • Page 20: Rebooting The System

    Dgs-3100 series gigabit stackable managed switch user manual rebooting the system the system reboot page provides a method for selecting one, or all of the units to be rebooted. To reboot the system: 1. Click > system reboot. The system reboot page opens: figure 1-6 system reboot page the system reb...

  • Page 21

    Dgs-3100 series gigabit stackable managed switch user manual using the web system components the following table contains information regarding the list of buttons: 9 name description component activate activates field commands add adds selected items all selects all apply applies field settings bac...

  • Page 22

    Dgs-3100 series gigabit stackable managed switch user manual 10 2 configuring basic configuration this section contains information for viewing device information, defining ip addresses, managing stacking, defining port parameters, configuring system user accounts, configuring and managing system lo...

  • Page 23: Viewing Device Information

    Dgs-3100 series gigabit stackable managed switch user manual viewing device information the device information page contains parameters for configuring general device information, including the system name, location, and contact, the system mac address, system up time, and mac addresses, and both so...

  • Page 24

    Dgs-3100 series gigabit stackable managed switch user manual 12 field description boot version displays the installed device boot version number. Mac address displays the mac address assigned to the device. Ip address displays the ip address assigned to the device. Subnet mask displays the subnet ma...

  • Page 25: Defining System Information

    Dgs-3100 series gigabit stackable managed switch user manual defining system information the system information page provides device information about specific stacking members. To view system information: 1. Click configuration > system information. The system information page opens: figure 2-2 sys...

  • Page 26: Defining Ip Addresses

    Dgs-3100 series gigabit stackable managed switch user manual 14 defining ip addresses the ip address page contains fields for assigning ip addresses. Packets are forwarded to the default ip when frames are sent to a remote network via the default gateway. The configured ip address must belong to the...

  • Page 27: Managing Stacking

    Dgs-3100 series gigabit stackable managed switch user manual managing stacking stacking enhances network flexibility by building virtual switches with more ports then are available in a single device. Stacks are managed by stacking member which called stack master., all other stacking members serve ...

  • Page 28

    Dgs-3100 series gigabit stackable managed switch user manual 16 stacking members maintain the assigned unit id even after the stacking member is rebooted. The stack master may reallocate ids during system initialization to resolve duplicate id conflicts. Manually assigned ids cannot be changed by th...

  • Page 29: Stack Startup Process

    Dgs-3100 series gigabit stackable managed switch user manual 17 electing a stacking master whenever a stacking member (or more than one) comes up, one of the stacking members is elected to be the stack master. The stack master is selected as follows: • if one of the master enabled stacking members i...

  • Page 30

    Dgs-3100 series gigabit stackable managed switch user manual 18 these stacking members do not participate in the master election process, and if no stack master is present, the stacking members’ network ports are shut down. Only the stacking ports are operational. Both the stack master and all other...

  • Page 31

    Dgs-3100 series gigabit stackable managed switch user manual building stacks – quick start the dgs-3100 series supports the following stacking scenarios: • building a new stack from scratch • increasing the stack by adding units to an existing stack this section contains the following topics: • stac...

  • Page 32: Stack Management Examples

    Dgs-3100 series gigabit stackable managed switch user manual 20 this section contains the following topics: • building new manually ordered stacks • adding stacking members to an existing manually ordered stack building new manually ordered stacks to build new a self ordered stack: 1. Connect the un...

  • Page 33

    Dgs-3100 series gigabit stackable managed switch user manual – if the new stacking member has a unit id of 1 or 2, i.E. The stacking member is a master enabled unit, the new stacking member initiates the master election process. However, since the running stack master has a longer up-time, it remain...

  • Page 34

    Dgs-3100 series gigabit stackable managed switch user manual 22 unit id 1, and serving as the stack backup master, while the already running stacking member with unit id 2 remains the active stack master. • the stack master performs unit id allocation and conflict resolution process. – if the new st...

  • Page 35

    Dgs-3100 series gigabit stackable managed switch user manual – if the stack masterremains in this sub-group, the behavior is the same as described above. If the backup master remains in this sub group the behavior is the same as described in0 - replacing a failed stack master . Note: if a stack is d...

  • Page 36

    Dgs-3100 series gigabit stackable managed switch user manual 24 merging stacks this example assumes that the user would like to merge two working stacks. This creates one stack from two separate stacks. There are two scenarios: if new stacking members are powered down during insertion and then power...

  • Page 37

    Dgs-3100 series gigabit stackable managed switch user manual 25 • a running stacking member group is added to an existing stack, assuming each one of the stack groups has an elected stack master. The total of existing stacking members and new stacking members exceeds the maximum allowed number of st...

  • Page 38: Configuring Stacking

    Dgs-3100 series gigabit stackable managed switch user manual 26 configuring stacking the stacking settings page allows network managers to execute force master and to change each and every unit its own unit id. To complete the changing process the user need to reboot the unit. 1. Click configuration...

  • Page 39: Defining Ports

    Dgs-3100 series gigabit stackable managed switch user manual defining ports • configuring port properties • viewing port properties configuring port properties the port setting page contains parameters for configuring port properties. Gigabit ports operate in full duplex mode only, and take on certa...

  • Page 40

    Dgs-3100 series gigabit stackable managed switch user manual 28 field description 100m/full — indicates the port is currently operating at 100 mbps and full duplex mode. 100m/half — indicates the port is currently operating at 100 mbps and half duplex mode. 1000m/full — indicates the port is current...

  • Page 41: Viewing Port Properties

    Dgs-3100 series gigabit stackable managed switch user manual viewing port properties the port description page allows network managers provide a description of device ports. To define a port description: 1. Click configuration > >port configuration > port description. The port description page opens...

  • Page 42: Arp Settings

    Dgs-3100 series gigabit stackable managed switch user manual 30 arp settings the address resolution protocol (arp) converts ip addresses into physical addresses and maps the ip address to a mac address. Arp allows a host to communicate with other hosts only when the ip addresses of its neighbors are...

  • Page 43: Configuring User Accounts

    Dgs-3100 series gigabit stackable managed switch user manual configuring user accounts user accounts including user passwords and access rights are defined on the user accounts page. To define user account information: 1. Click configuration > user accounts. The user accounts page opens: figure 2-8 ...

  • Page 44

    Dgs-3100 series gigabit stackable managed switch user manual 32 to edit the user accounts page: 1. Select a name on the user list. 2. Click . 3. Define the value. 4. Click . The new access rights are saved, and device is updated. To delete a user accounts page entry: 1. Select an entry. 2. Click . T...

  • Page 45: Managing System Logs

    Dgs-3100 series gigabit stackable managed switch user manual managing system logs system logs record and manage events and report errors and informational messages. Event messages have a unique format, as per the syslog protocols recommended message format for all error reporting. For example, syslo...

  • Page 46: Configuring Sntp

    Dgs-3100 series gigabit stackable managed switch user manual 34 to delete a log entry: 1. Select the entry. 2. Click . The entry is deleted, and the device is updated. Configuring sntp the device supports the simple network time protocol (sntp). Sntp assures accurate network device clock time synchr...

  • Page 47

    Dgs-3100 series gigabit stackable managed switch user manual figure 2-10 time settings page the time settings page contains the following fields: status field description time source defines the time source by which the system time is set. The possible field values are: sntp — indicates that the sys...

  • Page 48

    Dgs-3100 series gigabit stackable managed switch user manual 36 configuring daylight savings time the timezone settings page contains fields for defining system time parameters for both the local hardware clock and the external sntp clock. If the system time is kept using an external sntp clock, and...

  • Page 49

    Dgs-3100 series gigabit stackable managed switch user manual • montenegro — from the last weekend of march until the last weekend of october. • netherlands — from the last weekend of march until the last weekend of october. • new zealand — from the first sunday in october until the first sunday on o...

  • Page 50

    Dgs-3100 series gigabit stackable managed switch user manual 38 the timezone settings page contains the following fields: field description daylight savings time state defines type of dst enabled on the device. The possible field values are: disable — disables dst on the device. This is the default ...

  • Page 51

    Dgs-3100 series gigabit stackable managed switch user manual dst annual settings section the annual mode enables setting a dst seasonal time adjustment. This option requires defining begin and end times by the specific dates. For example, the network administrator defines that dst begins april 3 and...

  • Page 52: Configuring Snmp

    Dgs-3100 series gigabit stackable managed switch user manual 40 configuring snmp simple network management protocol (snmp) provides a method for managing network devices. The device supports the following snmp versions: • snmp version 1 • snmp version 2c • snmp version 3 snmp v1 and v2c the snmp age...

  • Page 53: Defining Snmp Views

    Dgs-3100 series gigabit stackable managed switch user manual defining snmp views snmp views provide or block access to device features or aspects of features. For example, a view can be defined to show that snmp view a has included access to multicast groups, while snmp view b has excluded access to...

  • Page 54: Defining Snmp Groups

    Dgs-3100 series gigabit stackable managed switch user manual 42 defining snmp groups the snmp group table page provides information for creating snmp groups and assigning snmp access control privileges to snmp groups. Groups enable network managers to assign access rights to specific device features...

  • Page 55

    Dgs-3100 series gigabit stackable managed switch user manual field description notify view name defines a notify view. The notify view sends traps for the assigned snmp view. This is applicable for snmpv3 only. The possible values are: community/view testreadview pwriteview privateview security mode...

  • Page 56: Defining Snmp Users

    Dgs-3100 series gigabit stackable managed switch user manual 44 defining snmp users the snmp user table page enables assigning system users to snmp groups and defining the user authentication method. To assign system users: 1. Click configuration > smnp settings >snmp user table. The snmp user table...

  • Page 57

    Dgs-3100 series gigabit stackable managed switch user manual field description auth-protocol by key selects the authentication key type used to authenticate users. The possible field values are: md5 — defines that users are authenticated via a hmac-md5 algorithm key. Sha — defines that users are aut...

  • Page 58: Defining Snmp Communities

    Dgs-3100 series gigabit stackable managed switch user manual 46 defining snmp communities access rights are managed by defining communities, using the snmp community table page. When the community names are changed, access rights are also changed. Snmp communities are defined only for snmp v1 and sn...

  • Page 59: Defining Snmp Host Table

    Dgs-3100 series gigabit stackable managed switch user manual defining snmp host table the snmp host table page contains information for defining filters that determine whether traps are sent to specific host, as well as the trap type sent. To define the snmp host table page: 1. Click configuration >...

  • Page 60

    Dgs-3100 series gigabit stackable managed switch user manual 48 the snmp host table page contains the following fields: field description host ip address defines the ip address to which the traps are sent. Snmp version defines the trap type. The possible field values are: snmpv1 — indicates that snm...

  • Page 61: Defining Snmp Engine Id

    Dgs-3100 series gigabit stackable managed switch user manual defining snmp engine id the engine id is a unique identifier used for snmp v3 implementations. This is an alphanumeric string used to identify the snmp engine on the switch. To define the snmp engine id: 1. Click configuration > smnp setti...

  • Page 62: Enabling Snmp Traps

    Dgs-3100 series gigabit stackable managed switch user manual 50 enabling snmp traps the snmp configuration trap page contains parameters for defining snmp notification parameters. To enable snmp notifications: to enable snmp traps: 1. Click configuration > smnp settings > snmp trap configuration. Th...

  • Page 63: Dhcp Auto Configuration

    Dgs-3100 series gigabit stackable managed switch user manual dhcp auto configuration in the dhcp auto configuration page, users can enable or disable automatic download of the latest image and configuration files from the dhcp server. During reboot, if dhcp auto configuration is enabled, the device ...

  • Page 64: Dual Image Services

    Dgs-3100 series gigabit stackable managed switch user manual 52 dual image services the device contains two software images, one for reboot and one for backup, in its flash memory. When a software download is successfully completed, the new image automatically becomes the new reboot file, unless the...

  • Page 65: Config Firmware Image

    Dgs-3100 series gigabit stackable managed switch user manual config firmware image theconfig firmware image config firmware image page allows users to change each device’s image file. To change the reboot file: 1. Click configuration > dual image services > config firmware image. The config firmware...

  • Page 66: Configuring L2 Features

    Dgs-3100 series gigabit stackable managed switch user manual 54 3 configuring l2 features this section contains information for enabling and configuring l2 features. This section contains the following topics: • enabling jumbo frames • configuring vlans • configuring gvrp • defining trunking • traff...

  • Page 67: Enabling Jumbo Frames

    Dgs-3100 series gigabit stackable managed switch user manual enabling jumbo frames jumbo frame support is designed to enhance ethernet networking throughput and significantly reduce the cpu utilization of large file transfers like large multimedia files or large data files by enabling more efficient...

  • Page 68: Configuring Vlans

    Dgs-3100 series gigabit stackable managed switch user manual 56 configuring vlans understanding ieee 802.1p priority priority tagging is an ieee 802.1p defined standard function designed to provide a means of managing traffic on networks where many different types of data are transmitted simultaneou...

  • Page 69

    Dgs-3100 series gigabit stackable managed switch user manual term description untagging the act of stripping 802.1q vlan information out of the packet header. Ingress port a port on a switch where packets are flowing into the switch and vlan decisions must be made. Egress port a port on a switch whe...

  • Page 70: 802.1Q Vlan Tags

    Dgs-3100 series gigabit stackable managed switch user manual 58 802.1q vlan tags the figure below shows the 802.1q vlan tag. There are four additional octets inserted after the source mac address. Their presence is indicated by a value of 0x8100 in the ethertype field. When a packet's ethertype fiel...

  • Page 71: Port Vlan Id

    Dgs-3100 series gigabit stackable managed switch user manual 59 port vlan id tagged packets (carrying the 802.1q vid information) can be transmitted from one 802.1q compliant network device to another with the vlan information intact. This allows 802.1q vlans to span network devices (and the entire ...

  • Page 72: Default Vlans

    Dgs-3100 series gigabit stackable managed switch user manual 60 the ingress port. If it does not, the packet is dropped. If it has the same vid, the packet is forwarded and the destination port transmits it on its attached network segment. This process is referred to as ingress filtering, and is use...

  • Page 73: Defining Vlan Properties

    Dgs-3100 series gigabit stackable managed switch user manual defining vlan properties the vlan configuration page provides information and global parameters for configuring and working with vlans. 1. Click l2 features > 802.1q vlan. The vlan configuration page opens: figure 3–5. Vlan configuration p...

  • Page 74

    Dgs-3100 series gigabit stackable managed switch user manual 62 2. Click the add/edit vlan tab. The add/edit vlan information page opens: figure 3–6. Add/edit vlan information page the add/edit vlan information page contains the following fields: field description vid defines the vlan id. Vlan name ...

  • Page 75: Configuring Gvrp

    Dgs-3100 series gigabit stackable managed switch user manual configuring gvrp gvrp timers need to be in the default values on all layer 2-connected devices. If the gvrp timers are set differently on the layer 2-connected devices, the gvrp application does not operate successfully. Garp vlan registra...

  • Page 76

    Dgs-3100 series gigabit stackable managed switch user manual 64 the gvrp setting page contains the following fields: field description defineswhether grvp is enabled on the device. The possible field values are: grvp global setting enabled — enables grvp on the device. Disabled — disables grvp on th...

  • Page 77: Defining Trunking

    Dgs-3100 series gigabit stackable managed switch user manual defining trunking the trunking configuration page contains information for assigning ports to lags and defining lag parameters. To assign ports to lags: 1. Click l2 features > trunking. The trunking configuration page opens: figure 3–8. Tr...

  • Page 78

    Dgs-3100 series gigabit stackable managed switch user manual 66 notes about trunking on the dgs-3100 series dgs-3100 series supports up to 32 lags per device (or stack). Note: a port must belong to the default vlan when the user is adding the port to a lag, after adding the port to the lag, the lag ...

  • Page 79: Traffic Segmentation

    Dgs-3100 series gigabit stackable managed switch user manual traffic segmentation the traffic segmentation page enables administrators to force traffic from source ports to bypass the forwarding database (fdb), and forward all unicast, multicast and broadcast traffic to the forwarding port,. Forward...

  • Page 80: Configuring Lacp

    Dgs-3100 series gigabit stackable managed switch user manual 68 configuring lacp lag ports can contain different media types if the ports are operating at the same speed. Aggregated links can be set up manually or automatically established by enabling lacp on the relevant links. Aggregate ports can ...

  • Page 81: Defining Igmp Snooping

    Dgs-3100 series gigabit stackable managed switch user manual defining igmp snooping when igmp snooping is enabled globally, all igmp packets are forwarded to the cpu. The cpu analyzes the incoming packets and determines the following information: – which ports want to join which multicast groups. – ...

  • Page 82

    Dgs-3100 series gigabit stackable managed switch user manual 70 field description 16711450 seconds. Host timeout defines the time the host waits to receive a message before timing out. The default time is 260 seconds. The field range is 60-16711450 seconds. Router timeout defines the time the multic...

  • Page 83

    Dgs-3100 series gigabit stackable managed switch user manual field description host timeout defines the time the host waits to receive a message before timing out. The default time is 260 seconds. The field range is 60-16711450 seconds. Router timeout defines the time the multicast router waits to r...

  • Page 84: Configuring Port Mirroring

    Dgs-3100 series gigabit stackable managed switch user manual 72 configuring port mirroring switches inherently forward frames to relevant ports only. This creates difficulty when traffic needs to be monitored, either for information gathering (such as statistical analysis, security traces, etc.) or ...

  • Page 85

    Dgs-3100 series gigabit stackable managed switch user manual field description none defines that port mirroring is not applied to the ports. 2. Define the status, unit, and target fields. 3. Click to activate the port mirroring function. 4. Define the unit, tx, and rx. Fieldsunder source port settin...

  • Page 86: Configuring Spanning Tree

    Dgs-3100 series gigabit stackable managed switch user manual 74 configuring spanning tree spanning tree protocol (stp) provides tree topography for any arrangement of bridges, as well as providing a single path between end stations on a network, thus eliminating loops. Loops occur when alternate rou...

  • Page 87

    Dgs-3100 series gigabit stackable managed switch user manual defining spanning tree global parameters while classic stp prevents layer 2 forwarding loops in a general network topology, convergence can take between 30-60 seconds. This time may delay detecting possible loops and propagating status top...

  • Page 88

    Dgs-3100 series gigabit stackable managed switch user manual 76 field description disabled – bpdu forwarding is disabled on the device. (this is the default value) bridge priority (0 – 61440) specifies the selected spanning tree instance device priority. The field range is 0-61440. The default value...

  • Page 89: Defining Stp Port Settings

    Dgs-3100 series gigabit stackable managed switch user manual defining stp port settings stp can be set up on a port per port basis. In addition to setting spanning tree parameters for use at the switch level, the switch enables configuring groups of ports, in which case each port-group has its own s...

  • Page 90

    Dgs-3100 series gigabit stackable managed switch user manual 78 field description packets. Edge indicates whether the selected port is an edge port. The possible field values are: true — defines the port as an edge port. Edge ports cannot create loops; however, they can lose edge port status if a to...

  • Page 91

    Dgs-3100 series gigabit stackable managed switch user manual defining multiple spanning tree configuration identification multiple spanning tree (mstp) provides various load balancing scenarios by allowing multiple vlans to be mapped to a single spanning tree instance, providing multiple pathways ac...

  • Page 92

    Dgs-3100 series gigabit stackable managed switch user manual 80 4. Click to an id row to edit the id value. 5. Define the new value. 6. Click . The multiple spanning tree configuration identification is defined, and the device is updated. Defining mstp port information network administrators can ass...

  • Page 93

    Dgs-3100 series gigabit stackable managed switch user manual field description another port for forwarding disabled — disables the port for the specific instance. Role indicates the port role assigned by the stp algorithm to provide to stp paths. The possible field values are: enabled — enables the ...

  • Page 94: Defining Unicast Forwarding

    Dgs-3100 series gigabit stackable managed switch user manual 82 defining forwarding and filtering this section contains information for configuring both unicast and multicast filtering, and contains the following topics: • defining unicast forwarding • defining multicast forwarding defining unicast ...

  • Page 95

    Dgs-3100 series gigabit stackable managed switch user manual to edit a fdb table entry: 1. Select the entry. 2. Click . 3. Define the values. 4. Click . The entry is updated, and the device is updated. To delete a fdb table entry: 1. Select the entry. 2. Click . The entry is deleted, and the device ...

  • Page 96

    Dgs-3100 series gigabit stackable managed switch user manual 84 3. Select either all, or individual ports: – click to select all ports as none or egress; – alternatively, click to select the ports individually. The default is 1-48 none. 4. Click .The multicast forwarding settings are applied to the ...

  • Page 97

    Dgs-3100 series gigabit stackable managed switch user manual 85 4 configuring quality of service configuring 1p priority tagging is an ieee 802.1p defined standard function designed to provide a means of managing traffic on networks where many different types of data are transmitted simultaneously. ...

  • Page 98

    Dgs-3100 series gigabit stackable managed switch user manual 86 figure 4-1. Mapping qos on the switch the picture above shows the default priority setting for the switch. Class-3 has the highest priority of the four priority queues on the switch. In order to implement qos, the user is required to in...

  • Page 99: Understanding Qos

    Dgs-3100 series gigabit stackable managed switch user manual 87 understanding qos the switch has four priority queues. These priority queues are labeled as 3 (the highest queue) to 0 (the lowest queue). The eight (0-7) priority tags, specified in ieee 802.1p are mapped to the switch's priority tags ...

  • Page 100: Defining Bandwidth Settings

    Dgs-3100 series gigabit stackable managed switch user manual 88 defining bandwidth settings the bandwidth control page allows network managers to define the bandwidth settings for a specified ingress interface. 1. Click qos > bandwidth control. The bandwidth control page opens: figure 4-2. Bandwidth...

  • Page 101: Configuring Storm Control

    Dgs-3100 series gigabit stackable managed switch user manual configuring storm control storm control limits the amount of multicast, broadcast and unknown unicast frames accepted and forwarded by the device. When layer 2 frames are forwarded, broadcast, multicast and unknown unicast frames are flood...

  • Page 102

    Dgs-3100 series gigabit stackable managed switch user manual 90 3. Click . The storm control settings are configured, and the device is updated. Mapping ports to packet priorities the 802.1p default priority page provides traffic classification. By assigning priority values per port. The priority va...

  • Page 103

    Dgs-3100 series gigabit stackable managed switch user manual mapping priority to classes (queues) the 802.1p user priority page allows network managers to assign priority tags to classes (queues). If a network manager defines a priority of 01 to class 3, all packets arriving with an assigned value o...

  • Page 104

    Dgs-3100 series gigabit stackable managed switch user manual 92 configuring qos scheduling mechanism the qos scheduling mechanism page contains fields for defining the qos scheduling forwarding scheme. To define the qos scheduling mechanism: 1. Click qos > qos scheduling mechanism. The qos schedulin...

  • Page 105

    Dgs-3100 series gigabit stackable managed switch user manual defining multi-layer cos settings for network administrators wanting to configure multi layer cos settings, implementation in the switch is done via the access control list. Hence, the multi-layer cos setting page has two hyperlinks; one t...

  • Page 106: Security Features

    Dgs-3100 series gigabit stackable managed switch user manual 94 5 security features this section contains information for enabling and configuring device security including user accounts. • configuring safeguard engine • configuring trust host • configuring port security • configuring guest vlans • ...

  • Page 107: Configuring Safeguard Engine

    Dgs-3100 series gigabit stackable managed switch user manual configuring safeguard engine the safeguard engine page allows network administrators to set network alarms to protect the cpu from attacks, based on rising and falling threshold levels of broadcasts and cpu utilization. The safeguard mecha...

  • Page 108: Configuring Trust Host

    Dgs-3100 series gigabit stackable managed switch user manual 96 configuring trust host the trusted host page permits network managers to manage the device from remote stations. Network managers can configure up to three remote stations. Ensure that the remote stations are configured with the ip addr...

  • Page 109: Configuring Port Security

    Dgs-3100 series gigabit stackable managed switch user manual configuring port security network security can be increased by limiting access on a specific port only to users with specific mac addresses. The mac addresses can be dynamically learned or statically configured. Locked port security monito...

  • Page 110: Configuring Guest Vlans

    Dgs-3100 series gigabit stackable managed switch user manual 98 field description max learning addr indicates the number of mac addresses that can be learned on the port. 2. Define the unit, from port, to port, max address (0-64), and admin state fields. 3. Click port security is enabled, and the de...

  • Page 111

    Dgs-3100 series gigabit stackable managed switch user manual 99 configuring port authentication 802.1x port-based authentication authenticates users on a per-port/per mac basis via an external server. Only authenticated and approved system users can transmit and receive data. Ports are authenticated...

  • Page 112

    Dgs-3100 series gigabit stackable managed switch user manual 100 to enable the 802.1x: 1. Click security > 802.1x setting. The 802.1x setting page opens: figure 5-12. 802.1x setting page the 802.1x setting page contains the following fields: field description 802.1x indicates if 802.1x is enabled on...

  • Page 113

    Dgs-3100 series gigabit stackable managed switch user manual field description value. Disabled — disables re-authenticating the port or mac addresses after the port or mac address authentication has timed out. Control indicates the host status. If there is an asterisk (*), the port is either not lin...

  • Page 114

    Dgs-3100 series gigabit stackable managed switch user manual 102 to enable mac authentication: 1. Click security > 802.1x setting. The 802.1x setting page opens: the 802.1x setting page contains the following fields: field description 802.1x indicates if 802.1x is enabled on the device. The possible...

  • Page 115

    Dgs-3100 series gigabit stackable managed switch user manual field description value. Disabled — disables re-authenticating the port or mac addresses after the port or mac address authentication has timed out. Control indicates the host status. If there is an asterisk (*), the port is either not lin...

  • Page 116: And Radius Pages)

    Dgs-3100 series gigabit stackable managed switch user manual 104 configuring mac authentication (by using guest vlan, 802.1x and radius pages) this is the sequence of operatons required to configure mac authentication in dgs-3100 series. 1. In order to configure a guest vlan, the user is required to...

  • Page 117

    Dgs-3100 series gigabit stackable managed switch user manual 3. After the ports were assigned to the guest vlan, the user needs to configure a radius server that will hold the mac authentication database. This should be done via click security > 802.1x > authentic radius server page according to the...

  • Page 118

    Dgs-3100 series gigabit stackable managed switch user manual 106 5. The second step on security > 802.1x > 802.1x setting page will be configuration of the required ports as ‘mac based’ authentication (opposite to ‘port based’ authentication) 6. The last step on security > 802.1x > 802.1x setting pa...

  • Page 119: Defining Radius Settings

    Dgs-3100 series gigabit stackable managed switch user manual defining radius settings remote authorization dial-in user service (radius) servers provide additional security for networks. Radius servers provide a centralized authentication method for management access. The default parameters are user...

  • Page 120

    Dgs-3100 series gigabit stackable managed switch user manual 108 4. Define the authentication port in the authentic port field. 5. Define the accounting port in the accounting port field. 6. Define the authentication and encryption key in the key field. 7. Reenter the radius key in the confirm key f...

  • Page 121

    Dgs-3100 series gigabit stackable managed switch user manual figure 5-14. Ssl configuration settings page the ssl configuration settings page contains the following fields: field description ssl status indicates if ssl is enable on the device. The possible field values are: enabled — indicates ssl i...

  • Page 122

    Dgs-3100 series gigabit stackable managed switch user manual 110 configuring secure shell security secure shell permits network users to securely login to the network from a remote location over an insecure network. Ssh a secure login to remote host computers, a safe method of executing commands on ...

  • Page 123

    Dgs-3100 series gigabit stackable managed switch user manual 3. Define the ssh global setting port number in the port (1-65535) field. 4. Click . The ssh configuration is defined, and the device is updated. Defining ssh algorithm settings this ssh algorithm settings page allows network administrator...

  • Page 124

    Dgs-3100 series gigabit stackable managed switch user manual 112 all algorithms are enabled by default. To enable ssh algorithms: 1. Click security > ssh > ssh algorithm settings. The ssh algorithm settings page opens: figure 5-16. Ssh algorithm settings page the ssh algorithm settings page contains...

  • Page 125

    Dgs-3100 series gigabit stackable managed switch user manual defining application authentication settings application authentication permits network administrators to assign authentication methods for user authentication. For example, console users can be authenticated by authentication list 1, whil...

  • Page 126

    Dgs-3100 series gigabit stackable managed switch user manual 114 configuring authentication server hosts the authentication server is a remote device connected to the same network as the client and authenticator. Users are authenticated using either radius or tacacs+, and must be authenticated by th...

  • Page 127: Defining Login Methods

    Dgs-3100 series gigabit stackable managed switch user manual 3. Click .The authentication host properties are defined, and the device is updated. • to edit an authentication, click adjacent to the relevant ip address on the list. The upper fields display the current values, which then can be edited....

  • Page 128

    Dgs-3100 series gigabit stackable managed switch user manual 116 field description are: radius — user authentication occurs at the radius server. Tacacs+ — the user authentication occurs at the tacacs+ server. None — no user authentication occurs. Local — user authentication occurs at the device lev...

  • Page 129: Defining Enable Methods

    Dgs-3100 series gigabit stackable managed switch user manual defining enable methods network users must first login to the device on the enable method lists page. Access as non-administrative users is granted. The enable method lists pageallows network mangers to assign user privileges using authent...

  • Page 130

    Dgs-3100 series gigabit stackable managed switch user manual 118 field description method 2 indicates the second method used to authenticate the network user. The possible field values are: radius — user authentication occurs at the radius server. Tacacs+ — the user authentication occurs at the taca...

  • Page 131

    Dgs-3100 series gigabit stackable managed switch user manual configuring local enable password the configure local enable password page allows network administrators to configure the local enabled password. To define the network local enable password: 1. Click security > access authentication contro...

  • Page 132: Monitoring The Device

    Dgs-3100 series gigabit stackable managed switch user manual 120 6 monitoring the device this section contains information for view device and packet statistics as well as, viewing igmp information and mac address information. This section includes the following topics: • viewing stacking informatio...

  • Page 133: Viewing Stacking Information

    Dgs-3100 series gigabit stackable managed switch user manual viewing stacking information the stacking information page provides specific information for stacked devices. To show the stacking information page: 1. Click , and from the menu select show stack status. 2. Alternatively, click monitoring ...

  • Page 134: Viewing Cpu Utilization

    Dgs-3100 series gigabit stackable managed switch user manual 122 viewing cpu utilization the cpu utilization page contains information about the system’s cpu utilization. 1. Click monitoring > cpu utilization. The cpu utilization page opens: figure 6-2. Cpu utilization page the cpu utilization page ...

  • Page 135: Viewing Port Utilization

    Dgs-3100 series gigabit stackable managed switch user manual viewing port utilization the port utilization page contains port utilization information for specific ports. To view port statistics: 1. Click monitoring > port utilization. The port utilization page opens: figure 6-3. Port utilization pag...

  • Page 136

    Dgs-3100 series gigabit stackable managed switch user manual 124 viewing packet size information the packet size page displays packets received by the switch, arranged in seven groups and classed by size, to be viewed as either a line graph or a table. 1. Click monitoring > packet size. The packet s...

  • Page 137

    Dgs-3100 series gigabit stackable managed switch user manual viewing received packet statistics the received(rx) page contains information about packets transmitted through device ports. To view received packet statistics: 1. Click monitoring > packets > received(rx). The received(rx) page opens: fi...

  • Page 138

    Dgs-3100 series gigabit stackable managed switch user manual 126 5. Click . The selected rx packet analysis is displayed. 6. Define the show/hide field. 7. To view the graph as a table, click view table . Viewing umb_cast packet statistics the umb_cast(rx) page displays the number of umb cast (unica...

  • Page 139

    Dgs-3100 series gigabit stackable managed switch user manual field description broadcast checked — displays the total amount of transmitted broadcast packets. 2. Define the unit and port fields. 3. Click to load the defined parameters. To clear the unit and port fields: 1. Click . The fields are cle...

  • Page 140

    Dgs-3100 series gigabit stackable managed switch user manual 128 field description values are: 1s - 5s, 10s, 15s, 20s, 30s, 40s, 50s, and 60s. Record number indicates the transmitted record number. Show/hide displays the bytes/packets received information. The possible field values are: bytes checke...

  • Page 141

    Dgs-3100 series gigabit stackable managed switch user manual viewing radius authenticated session statistics the radius authentication pageprovides radius authentication sessions, including how many sessions were initiated, which ports intimated the authentication sessions, and whether or not the se...

  • Page 142: Viewing Arp Table

    Dgs-3100 series gigabit stackable managed switch user manual 130 viewing arp table the browse arp table page provides information regarding arp vlans, including which ip address was mapped to what mac address. To view the arp table: 1. Click monitoring > browse arp table. The browse arp table page o...

  • Page 143: Viewing Router Ports

    Dgs-3100 series gigabit stackable managed switch user manual viewing router ports the browse router port page displays which ports are connected to routers. Ports can be connected to routers either as a static port or as a dynamic port. 1. Click monitoring > browse router port. The browse router por...

  • Page 144: Viewing Session Table

    Dgs-3100 series gigabit stackable managed switch user manual 132 viewing session table the browse session table page displays information regarding device sessions which were initiated by system users. To view session table information: 1. Click monitoring > browse session table. The browse session ...

  • Page 145

    Dgs-3100 series gigabit stackable managed switch user manual viewing igmp group information the igmp snooping group page contains vital igmp group information, including the multicast group ip address and the corresponding mac address through which the igmp packets passed. 1. Click monitoring >igmp ...

  • Page 146

    Dgs-3100 series gigabit stackable managed switch user manual 134 defining dynamic and static mac addresses packets addressed to destinations stored in either the static or dynamic databases are immediately forwarded to the port. The mac address table page can be sorted by interface, vlan, or mac add...

  • Page 147

    Dgs-3100 series gigabit stackable managed switch user manual 2. Select the stacking member in the unit field. 3. Define the port, vlan name, and mac address fields. 4. Click . – to view all entries, click . – to clear static entries, click . – to clear dynamic entries, click . – to clear all entries...

  • Page 148: Viewing System Log

    Dgs-3100 series gigabit stackable managed switch user manual 136 viewing system log the system log page provides information about system logs, including information when the device was booted, how the ports are operating, when users logged in, when sessions timed out, as well as other system inform...

  • Page 149

    Dgs-3100 series gigabit stackable managed switch user manual 137 7 managing power over ethernet devices power over ethernet (poe) provides power to devices over existing lan cabling, without updating or modifying the network infrastructure. Power over ethernet removes the necessity of placing networ...

  • Page 150

    Dgs-3100 series gigabit stackable managed switch user manual 138 defining poe system information the poe port setting page contains system poe information for enabling poe on the device, monitoring the current power usage, and enabling poe traps. To enable poe on the device: 1. Click poe > poe port ...

  • Page 151

    Dgs-3100 series gigabit stackable managed switch user manual fields description class 2 — indicates the power consumption is 7w. Class 3 — indicates the power consumption is 15.4w. Status indicates the inline power source status. The possible field values are: normal — indicates that the power suppl...

  • Page 152

    Dgs-3100 series gigabit stackable managed switch user manual 140 displaying and editing poe system information the poe system setting page displays system poe information on the device, monitoring the current power usage, and enabling poe traps. To display system poe information on the device: 1. Cl...

  • Page 153

    Dgs-3100 series gigabit stackable managed switch user manual 141 8 defining access profile lists access control lists (acl) allow network managers to define classification actions and rules for specific ingress ports. Packets entering an ingress port with an active acl are either admitted, denied or...

  • Page 154: Acl Configuration Wizard

    Dgs-3100 series gigabit stackable managed switch user manual 142 acl configuration wizard the acl configuration wizard page provides information for configuring access control lists. The acl configuration wizard page assists in configuring acls intuitively and quickly, and creates acl profiles and r...

  • Page 155

    Dgs-3100 series gigabit stackable managed switch user manual fields description tcp source port — matches the packet to the tcp source port tcp destination port — matches the packet to the tcp destination port udpall — specifies a udp packets filtering. Udp source port — matches the packet to the ud...

  • Page 156

    Dgs-3100 series gigabit stackable managed switch user manual 144 defining access profile lists this section contains the following topics: • adding acl profiles • defining level 2 acl • defining level 3 acl adding acl profiles the acl profile list page provides information for configuring acl profil...

  • Page 157

    Dgs-3100 series gigabit stackable managed switch user manual figure 8-3 add acl profile page the add acl profile page contains the following fields: field description l2 acl defines the acl profile layer 2 protocols. The possible values are: tagged — defines the profile layer 2 to match 802.1q field...

  • Page 158

    Dgs-3100 series gigabit stackable managed switch user manual 146 defining level 2 acl if l2 acl tagged is selected, the page updates as follows: figure 8-4 acl profile l2 acl tagged page to define l2 mac address acl profile: 1. Click the mac address button. The acl profile l2 acl tagged mac address ...

  • Page 159

    Dgs-3100 series gigabit stackable managed switch user manual the acl profile l2 acl tagged mac address page contains the following fields: field description source mac mask defines the range of source addresses relative to the acl rules (0=ignore, 1=check). For example, to set 00:00:00:00:10:xx, use...

  • Page 160

    Dgs-3100 series gigabit stackable managed switch user manual 148 to define l2 ether type acl profile this option defines whether or not the ether type field is checked for a match. 1. Click the ether type button. The acl profile l2 acl tagged ether type page updates to show the following: figure 8-7...

  • Page 161

    Dgs-3100 series gigabit stackable managed switch user manual if l2 acl untagged is selected, the page updates as follows (without the 802.1q vlan field): figure 8-8 acl profile l2 acl untagged page defining level 3 acl if l3 acl icmp is selected, the page updates as follows: figure 8-9 add acl profi...

  • Page 162

    Dgs-3100 series gigabit stackable managed switch user manual 150 to define l3 ipv4 dscp acl profile: this option defines whether or not the dscp field is checked for a match. 1. Click the ipv4 dscp button. The acl profile l3 acl icmp ipv4 dscp page updates to show the following: figure 8-10 acl prof...

  • Page 163

    Dgs-3100 series gigabit stackable managed switch user manual the acl profile l3 acl icmp ipv4 address page contains the following fields: field description source ip mask defines the range of source ip addresses, relevant to the acl rules. (0=ignore, 1=check). For example, to set 176.212.Xx.Xx, use ...

  • Page 164

    Dgs-3100 series gigabit stackable managed switch user manual 152 to define l3 igmp acl profile: this option defines whether or not the igmp field is checked for a match. If l3 acl igmp is selected, the page updates as follows: figure 8-13 acl profile l3 igmp page 1. Click the igmp button. The acl pr...

  • Page 165

    Dgs-3100 series gigabit stackable managed switch user manual 2. Click . The acl profile is added, and the device is updated. If l3 acl tcp is selected, the page updates as follows: figure 8-15 acl profile l3 tcp page to define l3 tcp port acl profile: 1. Click the tcp port button. The acl profile l3...

  • Page 166

    Dgs-3100 series gigabit stackable managed switch user manual 154 the acl profile l3 tcp port page contains the following fields: field description source port mask defines the range of source ports relevant to the acl rules. (0=ignore, 1=check). For example, to set 0 – 15, set mask of fff0. Destinat...

  • Page 167

    Dgs-3100 series gigabit stackable managed switch user manual if l3 acl udp is selected, the page updates as follows: figure 8-18 acl profile l3 udp page 1. Click the udp port button. The acl profile l3 udp port page updates to show the following: figure 8-19 acl profile l3 udp port page 155.

  • Page 168

    Dgs-3100 series gigabit stackable managed switch user manual 156 the acl profile l3 udp port page contains the following fields: field description source port mask defines the range of source ports relevant to the acl rules. (0=ignore, 1=check). For example, to set 0 – 15, set mask of f. Destination...

  • Page 169: Defining Access Rules Lists

    Dgs-3100 series gigabit stackable managed switch user manual defining access rules lists the following conditions can be defined as access rules: filter description source port ip address and wildcard mask filters the packets by the source port ip address and wildcard mask. Destination port ip addre...

  • Page 170

    Dgs-3100 series gigabit stackable managed switch user manual 158 to change acl rules: 1. Click . The add access rule page opens: figure 8-21 add access rule page (ip based acl) the add access rule page contains the following fields: field description profile id displays the profile id to which the r...

  • Page 171

    Dgs-3100 series gigabit stackable managed switch user manual 2. Define the rule detail fields. 3. Click . The rule is changed, and the device is updated. Note: each access profile must create rules with unuque access ids, access ids canno overlap in two different access profiles. 159.

  • Page 172: Finding Acl Rules

    Dgs-3100 series gigabit stackable managed switch user manual 160 finding acl rules the acl finder page identifies any rule which has been assigned to a specific port. To find acl rules: 1. Click acl > acl finder: the acl finder page opens: figure 8-22 acl finder page the acl finder page contains the...

  • Page 173

    Dgs-3100 series gigabit stackable managed switch user manual figure 8-23 rule detail page the rule detail page contains the following fields: field description profile id displays the profile id range. Source mac displays the source mac range. Destination mac displays the destination mac range. Ethe...

  • Page 174

    Dgs-3100 series gigabit stackable managed switch user manual 162 notes about ‘ip’ and ‘mac’ based acls in the dgs-3100 series acls can be configured in dgs-3100 series via the web gui in two ways: through the ‘acl configuration wizard’ screen (by automatic creation of profile and rule) and through t...

  • Page 175

    Dgs-3100 series gigabit stackable managed switch user manual notes about acls capacity in the dgs-3100 series • the user can create up to 15 access profiles. • the user can configure up to 240 access ids, each access id is unique i.E. The same access id can’t be created from two different access pro...

  • Page 176

    164 subject to the terms and conditions set forth herein, d-link systems, inc. (“d-link”) provides this limited warranty: • only to the person or entity that originally purchased the product from d-link or its authorized reseller or distributor. • only for products purchased and delivered within the...

  • Page 177

    165 d-link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an rma number is not visible from the outside of the package. The product owner agrees to pay d-link’s reasonable handling and return shipping charges for a...

  • Page 178: Product Registration

    166 product registration register your d-link product online at http://support.Dlink.Com/register/ product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights..

  • Page 179: Limited Warranty

    167 limited warranty d-link provides this limited warranty for its product only to the person or entity who originally purchased the product from d-link or its authorized reseller or distributor. D-link would fulfill the warranty obligation according to the local warranty policy in which you purchas...

  • Page 180

    168 d-link in writing, the replacement software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by d-link for the software. The warranty period shall extend for an additional ninety (90) days after any replacement software is delivered. If...

  • Page 181

    169 is not contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed. Initial installation, installation and removal of the product for repair, and shipping costs. Operational adjustments covered in the operating manual fo...

  • Page 182: Fcc Warning

    170 some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This limited warranty provides specific legal rights and the product owner may also have other...

  • Page 183: Technical Support

    Technical support technical support you can find software updates and user documentation on the d-link website. D-link provides free technical support for customers within the united states and within canada for the duration of the service period, and warranty confirmation service, during the warran...

  • Page 184: Technical Support

    172 technical support you can find software updates and user documentation on the d-link websites. If you require product support, we encourage you to browse our faq section on the web site before contacting the support line. We have many faq’s which we hope will provide you a speedy resolution for ...

  • Page 185: Technische Unterstützung

    Technische unterstützung aktualisierte versionen von software und benutzerhandbuch finden sie auf der website von d-link. D-link bietet kostenfreie technische unterstützung für kunden innerhalb deutschlands, Österreichs, der schweiz und osteuropas. Unsere kunden können technische unterstützung über ...

  • Page 186: Assistance Technique

    174 assistance technique vous trouverez la documentation et les logiciels les plus récents sur le site web d- link. Vous pouvez contacter le service technique de d-link par notre site internet ou par téléphone. Support technique destiné aux clients établis en france: assistance technique d-link par ...

  • Page 187: Asistencia Técnica

    Asistencia técnica puede encontrar las últimas versiones de software así como documentación técnica en el sitio web de d-link. D-link ofrece asistencia técnica gratuita para clientes residentes en españa durante el periodo de garantía del producto. Asistencia técnica de d-link por teléfono: +34 902 ...

  • Page 188: Supporto Tecnico

    176 supporto tecnico gli ultimi aggiornamenti e la documentazione sono disponibili sul sito d-link. Supporto tecnico per i clienti residenti in italia d-link mediterraneo s.R.L. Via n. Bonnet 6/b 20154 milano supporto tecnico dal lunedì al venerdì dalle ore 9.00 alle ore 19.00 con orario continuato ...

  • Page 189: Technical Support

    Technical support you can find software updates and user documentation on the d-link website. D-link provides free technical support for customers within benelux for the duration of the warranty period on this product. Benelux customers can contact d-link technical support through our website, or by...

  • Page 190: Pomoc Techniczna

    178 pomoc techniczna najnowsze wersje oprogramowania i dokumentacji użytkownika można znaleźć w serwisie internetowym firmy d-link. D-link zapewnia bezpłatną pomoc techniczną klientom w polsce w okresie gwarancyjnym produktu. Klienci z polski mogą się kontaktować z działem pomocy technicznej firmy d...

  • Page 191: Technická Podpora

    Technická podpora aktualizované verze software a uživatelských příruček najdete na webové stránce firmy d-link. D-link poskytuje svým zákazníkům bezplatnou technickou podporu zákazníci mohou kontaktovat oddělení technické podpory přes webové stránky, mailem nebo telefonicky web: http://www.Dlink.Cz/...

  • Page 192: Technikai Támogatás

    180 technikai támogatás meghajtó programokat és frissítéseket a d-link magyarország weblapjáról tölthet le. Telefonon technikai segítséget munkanapokon hétfőtől-csütörtökig 9.00 – 16.00 óráig és pénteken 9.00 – 14.00 óráig kérhet a (1) 461-3001 telefonszámon vagy a support@dlink.Hu emailcímen. Magya...

  • Page 193: Teknisk Support

    Teknisk support du kan finne programvare oppdateringer og bruker dokumentasjon på d-links web sider. D-link tilbyr sine kunder gratis teknisk support under produktets garantitid. Kunder kan kontakte d-links teknisk support via våre hjemmesider, eller på tlf. Teknisk support: d-link teknisk telefon s...

  • Page 194: Teknisk Support

    182 teknisk support du finder software opdateringer og bruger- dokumentation på d-link’s hjemmeside. D-link tilbyder gratis teknisk support til kunder i danmark i hele produktets garantiperiode. Danske kunder kan kontakte d-link’s tekniske support via vores hjemmeside eller telefonisk. D-link teknis...

  • Page 195: Teknistä Tukea Asiakkaille

    Teknistä tukea asiakkaille suomessa: d-link tarjoaa teknistä tukea asiakkailleen. Tuotteen takuun voimassaoloajan. Tekninen tuki palvelee seuraavasti: arkisin klo. 9 - 21 numerosta 0800-114 677 internetin kautta ajurit ja lisätietoja tuotteista. Http://www.Dlink.Fi sähköpostin kautta voit myös tehdä...

  • Page 196: Teknisk Support

    184 teknisk support på vår hemsida kan du hitta mer information om mjukvaru uppdateringar och annan användarinformation. D-link tillhandahåller teknisk support till kunder i sverige under hela garantitiden för denna produkt. Teknisk support för kunder i sverige: d-link teknisk support via telefon: 0...

  • Page 197: Suporte Técnico

    Suporte técnico você pode encontrar atualizações de software e documentação de utilizador no site de d-link portugal http://www.Dlink.Pt . A d-link fornece suporte técnico gratuito para clientes no portugal durante o período de vigência de garantia deste produto. Suporte técnico para clientes no por...

  • Page 198

    186 Τεχνική Υποστήριξη Μπορείτε να βρείτε software updates και πληροφορίες για τη χρήση των προϊόντων στις ιστοσελίδες της d-link Η d-link προσφέρει στους πελάτες της δωρεάν υποστήριξη στον Ελλαδικό χώρο Μπορείτε να επικοινωνείτε με το τμήμα τεχνικής υποστήριξης μέσω της ιστοσελίδας ή μέσω τηλεφώνου...

  • Page 199: Technical Support

    Technical support you can find software updates and user documentation on the d-link website. Tech support for customers in australia: tel: 1300-766-868 monday to friday 8:00am to 8:00pm est saturday 9:00am to 1:00pm est http://www.Dlink.Com.Au e-mail: support@dlink.Com.Au india: tel: 1800-222-002 m...

  • Page 200: Technical Support

    188 technical support you can find software updates and user documentation on the d-link website. Tech support for customers in egypt: tel: +202-2919035 or +202-2919047 sunday to thursday 9:00am to 5:00pm http://support.Dlink-me.Com e-mail: amostafa@dlink-me.Com iran: tel: +98-21-88822613 sunday to ...

  • Page 201

    Техническая поддержка Обновления программного обеспечения и документация доступны на Интернет-сайте d-link. D-link предоставляет бесплатную поддержку для клиентов в течение гарантийного срока. Клиенты могут обратиться в группу технической поддержки d-link по телефону или через Интернет. Техническая ...

  • Page 202: Asistencia Técnica

    190 asistencia técnica d-link latin américa pone a disposición de sus clientes, especificaciones, documentación y software mas reciente a través de nuestro sitio web www.Dlinkla.Com el servicio de soporte técnico tiene presencia en numerosos países de la región latino américa, y presta asistencia gr...

  • Page 203: Suporte Técnico

    Suporte técnico você pode encontrar atualizações de software e documentação de usuário no site da d-link brasil www.Dlinkbrasil.Com.Br. A d-link fornece suporte técnico gratuito para clientes no brasil durante o período de vigência da garantia deste produto. Suporte técnico para clientes no brasil: ...

  • Page 204

    192 d-link 友訊科技 台灣分公司 技術支援資訊 如果您還有任何本使用手冊無法協助您解決的產品相關問題，台灣 地區用戶可以透過我們的網站、電子郵件或電話等方式與d-link台灣 地區技術支援工程師聯絡。 d-link 免付費技術諮詢專線 0800-002-615 服務時間：週一至週五，早上8:30到晚上9:00 (不含周六、日及國定假日) 網 站：http://www.Dlink.Com.Tw 電子郵件：dssqa_service@dlink.Com.Tw 如果您是台灣地區以外的用戶，請參考d-link網站全球各地 分公司的聯絡資訊以取得相關支援服務。 產品保固期限、台灣區維修據點查詢...

  • Page 205: Dukungan Teknis

    Dukungan teknis update perangkat lunak dan dokumentasi pengguna dapat diperoleh pada situs web d-link. Dukungan teknis untuk pelanggan: dukungan teknis d-link melalui telepon: tel: +62-21-5731610 dukungan teknis d-link melalui internet: email : support@dlink.Co.Id website : http://support.Dlink.Co.I...

  • Page 206

    194 技 术 支持 您可以在 d-link 的官方網站找到產品的軟件升級和使用手冊 办公地址：北京市东城区北三环东路 36 号 环球贸易中心 b 座 26f 02-05 室 邮编: 100013 技术支持中心电话： 8008296688/ (028)66052968 技术支持中心传真： (028)85176948 维修中心地址：北京市东城区北三环东路 36 号 环球贸易中心 b 座 26f 02-05 室 邮编: 100013 维修中心电话： (010) 58257789 维修中心传真： (010) 58257790 网址： http://www.Dlink.Com.Cn.

  • Page 207: International Offices

    International offices 195 u.S.A 17595 mt. Herrmann street fountain valley, ca 92708 tel: 1-800-326-1688 url: www.Dlink.Com canada 2180 winston park drive oakville, ontario, l6h 5w1 canada tel: 1-905-8295033 fax: 1-905-8295223 url: www.Dlink.Ca europe (u. K.) d-link (europe) ltd d-link house, abbey r...

  • Page 208

    196 registration card all countries and regions excluding usa print, type or use block letters. Your name: mr./ms _____________________________________________________________________________ organization: ________________________________________________ dept. ____________________________ your title...

  • Page 209

    ______________________ ______________________ ______________________ ____________ 197.