1. DL manuals
  2. D-Link
  3. Switch
  4. DAS-3636
  5. Cli Reference Manual

D-Link DAS-3636 Cli Reference Manual

Manual is about: VDSL2 Switch Release 1.00

Summary of DAS-3636

  • Page 1

    Cli reference manual product model: das-3636 vdsl2 switch release 1.00

  • Page 2

    ____________________________________________________________________________ information in this document is subject to change without notice. © 2009 d-link corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of d-link corporation is strictly forbid...

  • Page 3

    Table of contents introduction............................................................................................................................1 using the console cli..........................................................................................................3 command syntax....

  • Page 4

    Igmp multicast vlan commands...................................................................................175 mld multicast vlan commands....................................................................................183 mld snooping command list................................................

  • Page 5

    Password recovery procedure.................................................................................474.

  • Page 6

    Das-3600 series ethernet over vdsl switch cli reference manual 1 i ntroduction the vdsl switch can be managed through the vdsl switch’s serial port, telnet, or the web-based management agent. The command line interface (cli) can be used to configure and manage the vdsl switch via the serial port or ...

  • Page 7

    Das-3600 series ethernet over vdsl switch cli reference manual setting the switch’s ip address each switch must be assigned its own ip address, which is used for communication with an snmp network manager or other tcp/ip application (for example bootp, tftp). The switch’s default ip address is 10.90...

  • Page 8: Cli

    Das-3600 series ethernet over vdsl switch cli reference manual 2 u sing the c onsole cli the das-3600 series supports a console management interface that allows the user to connect to the switch’s management agent via a serial port and a terminal or a computer running a terminal emulation program. T...

  • Page 9

    Das-3600 series ethernet over vdsl switch cli reference manual ? Cable_diag ports cfm linktrace cfm loopback clear clear address_binding dhcp_snoop binding_entry ports clear arptable clear attack_log clear cfm pkt_cnt clear counters clear ethernet_oam ports clear fdb clear historical_counters ports ...

  • Page 10

    Das-3600 series ethernet over vdsl switch cli reference manual in the above example, the command config account was entered without the required parameter , the cli returned the next possible completions: prompt. The up arrow cursor control key was pressed to re-enter the previous command (config ac...

  • Page 11

    Das-3600 series ethernet over vdsl switch cli reference manual 3 c ommand s yntax the following symbols are used to describe how command entries are made and values and arguments are specified in this manual. The online help contained in the cli and available through the console interface uses the s...

  • Page 15

    Das-3600 series ethernet over vdsl switch cli reference manual show account purpose used to display user accounts. Syntax show account description this command is used to display all user accounts created on the switch. Up to 8 user accounts can exist at one time. Parameters none. Restrictions only ...

  • Page 16

    Das-3600 series ethernet over vdsl switch cli reference manual show session purpose used to display a list of currently logged-in users. Syntax show session description this command is used to display a list of all the users that are logged-in at the time the command is issued. Parameters none. Rest...

  • Page 17

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display the switch’s information: das-3626:admin#show switch command: show switch device type : das-3600-12 gigabit ethernet switch mac address : 00-21-91-af-37-d0 ip address : 10.24.73.21 (manual) vlan name : default s...

  • Page 18

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display the switch status: 13.

  • Page 19

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show device_status command: show device_status das-3626:admin#show device_status command: show device_status power status: ac active dc status: dc power does not exist ac status: ac power exist fan tray insert fan rpm max ...

  • Page 20

    Das-3600 series ethernet over vdsl switch cli reference manual 15.

  • Page 21

    Das-3600 series ethernet over vdsl switch cli reference manual show serial_port purpose used to display the current serial port settings. Syntax show serial_port description this command is used to display the current serial port settings. Parameters none. 16.

  • Page 22

    Das-3600 series ethernet over vdsl switch cli reference manual show serial_port restrictions none. 17.

  • Page 23

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display the serial port settings: 18.

  • Page 24

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show serial_port command: show serial_port baud rate : 115200 data bits : 8 parity bits : none stop bits : 1 auto-logout : 10 mins das-3626:admin# 19.

  • Page 25

    Das-3600 series ethernet over vdsl switch cli reference manual 20

  • Page 27

    Das-3600 series ethernet over vdsl switch cli reference manual config serial_port restrictions only administrator and operator-level users can issue this command. 22.

  • Page 28

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to configure baud rate: das-3626:admin#config serial_port baud_rate 115200 command: config serial_port baud_rate 115200 success. Das-3626:admin# enable clipaging purpose used to pause the scrolling of the console screen wh...

  • Page 29

    Das-3600 series ethernet over vdsl switch cli reference manual enable telnet purpose used to enable communication with and management of the switch using the telnet protocol. Syntax enable telnet description this command is used to enable the telnet protocol on the switch. The user can specify the t...

  • Page 30

    Das-3600 series ethernet over vdsl switch cli reference manual command: enable web 80 success. Das-3626:admin# disable web purpose used to disable the http-based management software on the switch. Syntax disable web description this command disables the web-based management software on the switch. P...

  • Page 31

    Das-3600 series ethernet over vdsl switch cli reference manual reboot purpose used to restart the switch. Syntax reboot {force_agree} description this command is used to restart the switch. Parameters force_agree − when force_agree is specified, the reboot command will be executed immediatedly witho...

  • Page 32

    Das-3600 series ethernet over vdsl switch cli reference manual login purpose used to log in a user to the switch’s console. Syntax login description this command is used to initiate the login procedure. The user will be prompted for a username and password. Parameters none. Restrictions none. Exampl...

  • Page 34

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#config command_prompt atyourservice command: config command_prompt atyourservice success. Atyourservice:admin5# config greeting _message purpose used to configure the login banner (greeting message). Syntax config greeting...

  • Page 35

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#config command_prompt atyourservice command: config command_prompt atyourservice success. Atyourservice:admin5# restrictions only administrator and operator-level users can issue this command. Other restrictions include: •...

  • Page 36

    Das-3600 series ethernet over vdsl switch cli reference manual show greeting_message purpose used to view the currently configured greeting message configured on the switch. Syntax show greeting_message description this command is used to view the currently configured greeting message on the switch....

  • Page 37

    Das-3600 series ethernet over vdsl switch cli reference manual 6 s witch u tility c ommands the switch utility commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. 32.

  • Page 40

    Das-3600 series ethernet over vdsl switch cli reference manual each command is listed, in detail, in the following sections. 35.

  • Page 42

    Das-3600 series ethernet over vdsl switch cli reference manual download restrictions the tftp server must be on the same ip subnet as the switch. Only administrator-level users can issue this command. 37.

  • Page 43

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to download a configuration file: das-3626:admin#download cfg_fromtftp 10.48.74.121 c:\cfg\setting.Txt command: download cfg_fromtftp 10.48.74.121 c:\cfg\setting.Txt connecting to server................... Done. Download c...

  • Page 44

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to configure firmware image 1 as a boot up section: das-3626:admin#config firmware image_id 1 boot_up command: config firmware image_id 1 boot_up success. Das-3626:admin# show firmware information purpose used to display t...

  • Page 46

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show config current_config command: show config current_config #------------------------------------------------------ # das-3600-12 configuration # # firmware: build 1.00.B042 # copyright(c) 2009 d-link corporation. All r...

  • Page 47

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to upload a configuration file: das-3626:admin#upload cfg_totftp 10.48.74.121 c:\cfg\configuration.Txt command: upload cfg_totftp 10.48.74.121 c:\cfg\configuration.Txt connecting to server................... Done. Upload c...

  • Page 51

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display ip interface settings. Das-3626:admin#show ipif system command: show ipif system ip interface : system vlan name : default interface admin state : enabled link status : linkup ipv4 address : 10.24.73.21/8 (manua...

  • Page 53

    Das-3600 series ethernet over vdsl switch cli reference manual 8 r outing t able c ommands the routing table commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create iproute [default ] {} delete iproute [default...

  • Page 54

    Das-3600 series ethernet over vdsl switch cli reference manual show iproute purpose used to display the switch’s current ip routing table. Syntax show iproute description this command will display the switch’s current ip routing table. Parameters none. Restrictions none. Example usage: to display th...

  • Page 55: 6 N

    Das-3600 series ethernet over vdsl switch cli reference manual 9 ip v 6 n eighbor d iscovery c ommands the following commands are used to detect ipv6 neighbors on the switch and to keep a running database about these neighbor devices. The ipv6 neighbor detection commands in the command line interfac...

  • Page 57

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: das-3626:admin#show ipv6 neighbor_cache ipif system all command: show ipv6 neighbor_cache ipif system all neighbor link layer address interface state ------------------------------- ------------------ ------------ ----- fe...

  • Page 58

    Das-3600 series ethernet over vdsl switch cli reference manual show ipv6 nd purpose used to display information regarding neighbor detection on the switch. Syntax show ipv6 nd {ipif } description this command is used to show information regarding the ipv6 neighbor detection function of the switch. U...

  • Page 59: Ip M

    Das-3600 series ethernet over vdsl switch cli reference manual 10 l imited ip m ulticast a ddress the limited ip multicast command allows the administrator to permit or deny access to a port or range of ports by specifying a range of multicast addresses. The limited ip multicast commands in the comm...

  • Page 60

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to create a multicast filter profile: das-3626:admin#create mcast_filter_profile ipv4 profile_id 2 profile_name rg command: create mcast_filter_profile ipv4 profile_id 2 profile_name rg success. Das-3626:admin# config mcas...

  • Page 64

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show limited_multicast_addr ipv4 ports 1,3 command: show limited_multicast_addr ipv4 ports 1,3 port : 1 access : deny profile id name multicast addresses ---------- -------------------------------- ------------------------...

  • Page 69

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show ports description command: show ports description port port settings connection address state speed/duplex/flowctrl speed/duplex/flowctrl learning ------- -------- --------------------- ---------------------- --------...

  • Page 70

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#enable jumbo_frame command: enable jumbo_frame the maximum size of jumbo frame is 10240 bytes. Success. Das-3626:admin# disable jumbo_frame purpose used to disable the jumbo frame function on the switch. Syntax disable jum...

  • Page 71: Arp C

    Das-3600 series ethernet over vdsl switch cli reference manual 12 arp c ommands the arp commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. 66.

  • Page 73

    Das-3600 series ethernet over vdsl switch cli reference manual command parameters clear arptable 68.

  • Page 74

    Das-3600 series ethernet over vdsl switch cli reference manual each command is listed, in detail, in the following sections. 69.

  • Page 75

    Das-3600 series ethernet over vdsl switch cli reference manual create arpentry purpose used to make a static entry into the arp table. Syntax create arpentry description this command is used to enter an ip address and the corresponding mac address into the switch’s arp table. Parameters − the ip add...

  • Page 76

    Das-3600 series ethernet over vdsl switch cli reference manual create arpentry restrictions only administrator and operator-level users can issue this command. The switch supports up to 255 static arp entries. 71.

  • Page 77

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to create a static arp entry for the ip address 10.48.74.121 and mac address 00:50:ba:00:07:36: 72.

  • Page 78

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#create arpentry 10.48.74.121 00-50-ba-00-07-36 command: create arpentry 10.48.74.121 00-50-ba-00-07-36 success. Das-3626:admin# 73.

  • Page 79

    Das-3600 series ethernet over vdsl switch cli reference manual 74.

  • Page 80

    Das-3600 series ethernet over vdsl switch cli reference manual config arpentry purpose used to configure a static entry in the arp table. Syntax config arpentry description this command is used to configure a static entry in the arp table. The user may specify the ip address and the corresponding ma...

  • Page 81

    Das-3600 series ethernet over vdsl switch cli reference manual config arpentry restrictions only administrator and operator-level users can issue this command. Example usage: to configure a static arp entry for the ip address 10.48.74.12 and mac address 00:50:ba:00:07:36: das-3626:admin#config arpen...

  • Page 85

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to delete an ip destination from the dhcp relay table: das-3626:admin#config dhcp_relay delete ipif system 10.58.44.6 command: config dhcp_relay delete ipif system 10.58.44.6 success. Das-3626:admin# config dhcp_relay opti...

  • Page 87

    Das-3600 series ethernet over vdsl switch cli reference manual show dhcp_relay purpose used to display the current dhcp/bootp relay configuration. Syntax show dhcp_relay {ipif } description this command will display the current dhcp relay configuration for the switch, or if an ip interface name is s...

  • Page 88

    Das-3600 series ethernet over vdsl switch cli reference manual enable dhcp_relay purpose used to enable the dhcp/bootp relay function on the switch. Syntax enable dhcp_relay description this command is used to enable the dhcp/bootp relay function on the switch. Parameters none. Restrictions only adm...

  • Page 89

    Das-3600 series ethernet over vdsl switch cli reference manual 14 e xternal a larm c ommands the external alarm commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters show external_alarm config external_alarm channel...

  • Page 90

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to configure the external alarm on channel 1: das-3626:admin# config external_alarm channel 1 message channel 1 alarm occurs command: config external_alarm channel 1 message channel 1 alarm occurs success. Das-3626:admin# ...

  • Page 91: (Snmp) C

    Das-3600 series ethernet over vdsl switch cli reference manual 15 n etwork m anagement (snmp) c ommands the switch supports the simple network management protocol (snmp) versions 1, 2c, and 3. Users can specify which version of the snmp users want to use to monitor and control the switch. The three ...

  • Page 93

    Das-3600 series ethernet over vdsl switch cli reference manual create snmp user by_key – requires the snmp user to enter a encryption key for authentication and privacy. The key is defined by specifying the key in hex form below. This method is not recommended. Auth − the user may also choose the ty...

  • Page 94

    Das-3600 series ethernet over vdsl switch cli reference manual delete snmp user purpose used to remove an snmp user from an snmp group and also to delete the associated snmp group. Syntax delete snmp user description this command is used to remove an snmp user from its snmp group and then deletes th...

  • Page 96

    Das-3600 series ethernet over vdsl switch cli reference manual show snmp view purpose used to display an snmp view previously created on the switch. Syntax show snmp view {} description this command is used to display an snmp view previously created on the switch. Parameters − an alphanumeric string...

  • Page 97

    Das-3600 series ethernet over vdsl switch cli reference manual create snmp community purpose used to create an snmp community string to define the relationship between the snmp manager and an agent. The community string acts like a password to permit access to the agent on the switch. One or more of...

  • Page 98

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#delete snmp community dlink command: delete snmp community dlink success. Das-3626:admin# 93.

  • Page 99

    Das-3600 series ethernet over vdsl switch cli reference manual 94.

  • Page 100

    Das-3600 series ethernet over vdsl switch cli reference manual show snmp community purpose used to display snmp community strings configured on the switch. Syntax show snmp community {} description this command is used to display snmp community strings that are configured on the switch. Parameters −...

  • Page 101

    Das-3600 series ethernet over vdsl switch cli reference manual show snmp community restrictions none. 96.

  • Page 102

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display the currently entered snmp community strings: das-3626:admin#show snmp community command: show snmp community snmp community table community name view name access right -------------- ----------- ------------ dl...

  • Page 104

    Das-3600 series ethernet over vdsl switch cli reference manual delete snmp group purpose used to remove an snmp group from the switch. Syntax delete snmp group description this command is used to remove an snmp group from the switch. Parameters − an alphanumeric name of up to 32 characters that will...

  • Page 105

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show snmp groups command: show snmp groups vacm access table settings group name : group3 readview name : readview writeview name : writeview notify view name : notifyview security model : snmpv3 security level : noauthnop...

  • Page 106

    Das-3600 series ethernet over vdsl switch cli reference manual 101.

  • Page 108

    Das-3600 series ethernet over vdsl switch cli reference manual create snmp host restrictions only administrator-level users can issue this command. Example usage: to create an snmp host to receive snmp messages: das-3626:admin#create snmp host 10.48.74.100 v3 auth_priv public command: create snmp ho...

  • Page 109

    Das-3600 series ethernet over vdsl switch cli reference manual show snmp host purpose used to display the recipient of snmp traps generated by the switch’s snmp agent. Syntax show snmp host {} description this command is used to display the ip addresses and configuration information of remote snmp m...

  • Page 110

    Das-3600 series ethernet over vdsl switch cli reference manual show snmp host restrictions none. 105.

  • Page 111

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display the currently configured snmp hosts on the switch: 106.

  • Page 112

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show snmp host command: show snmp host snmp host table host ip address snmp version community name/snmpv3 user name --------------- ------------ ------------------------------ 10.48.76.23 v2c private 10.48.74.100 v3 authpr...

  • Page 113

    Das-3600 series ethernet over vdsl switch cli reference manual 108.

  • Page 114

    Das-3600 series ethernet over vdsl switch cli reference manual show snmp v6host purpose used to display the recipient of snmp traps generated by the switch’s snmp agent. Syntax show snmp v6host {} description this command is used to display the ip addresses and configuration information of remote sn...

  • Page 115

    Das-3600 series ethernet over vdsl switch cli reference manual show snmp v6host restrictions none. 110

  • Page 116

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display the currently configured snmp hosts on the switch: 111.

  • Page 117

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show snmp v6host command: show snmp v6host snmp host table ------------------------------------------------------------------ host ipv6 address : ::c084:1 snmp version : v1 community name/snmpv3 user name : 2 total entries...

  • Page 118

    Das-3600 series ethernet over vdsl switch cli reference manual create trusted_host purpose used to create the trusted host. Syntax create trusted_host description this command is used to create the trusted host. The switch allows users to specify up to four ip addresses that are allowed to manage th...

  • Page 119

    Das-3600 series ethernet over vdsl switch cli reference manual management stations ip address ------------------ 10.62.32.1/32 10.62.32.1/16 total entries: 2 delete trusted_host ipaddr purpose used to delete a trusted host entry made using the create trusted_host command above. Syntax delete trusted...

  • Page 120

    Das-3600 series ethernet over vdsl switch cli reference manual delete trusted_host all purpose used to delete all trusted host entries made using the create trusted_host ipaddr and create trusted_host network commands above. Syntax delete trusted _host all description this command is used to delete ...

  • Page 121

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to turn on snmp authentication trap support: das-3626:admin#enable snmp authenticate_traps command: enable snmp authenticate_traps success. Das-3626:admin# show snmp traps purpose used to show snmp trap support on the swit...

  • Page 122

    Das-3600 series ethernet over vdsl switch cli reference manual disable snmp authenticate_traps purpose used to disable snmp authentication trap support. Syntax disable snmp authenticate_traps description this command is used to disable snmp authentication support on the switch. Parameters none. Rest...

  • Page 123

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#config snmp system_location hq 5f command: config snmp system_location hq 5f success. Das-3626:admin# config snmp system_name purpose used to configure the name for the switch. Syntax config snmp system_name description th...

  • Page 124

    Das-3600 series ethernet over vdsl switch cli reference manual disable snmp purpose used to disable the snmp interface access function. Syntax disable snmp description this command is used to disable the snmp function. When the snmp function is disabled, the network manager will not be able to acces...

  • Page 125: Sntp C

    Das-3600 series ethernet over vdsl switch cli reference manual 16 t ime and sntp c ommands the simple network time protocol (sntp) (an adaptation of the network time protocol (ntp)) commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table...

  • Page 126

    Das-3600 series ethernet over vdsl switch cli reference manual show sntp purpose used to display the sntp information. Syntax show sntp description this command will display sntp settings information including the source ip address, time and poll interval. Parameters none. Restrictions none. Example...

  • Page 127

    Das-3600 series ethernet over vdsl switch cli reference manual to disable sntp support: das-3626:admin#disable sntp command: disable sntp success. Das-3626:admin# config time purpose used to manually configure system time and date settings. Syntax config time description this command will configure ...

  • Page 128

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#config time_zone operator + hour 2 min 30 command: config time_zone operator + hour 2 min 30 success. Das-3626:admin# config dst purpose used to enable and configure time adjustments to allow for the use of daylight saving...

  • Page 129

    Das-3600 series ethernet over vdsl switch cli reference manual config dst e_time − configure the time of day to end dst. • − time is expressed using a 24-hour clock, in hours and minutes. S_date − configure the specific date (day of the month) to begin dst. • − the start date is expressed numericall...

  • Page 130: Vlan C

    Das-3600 series ethernet over vdsl switch cli reference manual 17 vlan c ommands the vlan commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create vlan tag {type 1q_vlan advertisement} create vlan vlanid { adver...

  • Page 131

    Das-3600 series ethernet over vdsl switch cli reference manual create vlan purpose used to create a vlan on the switch. Syntax create vlan tag { type 1q_vlan advertisement } description this command allows the user to create a vlan on the switch. Parameters − the name of the vlan to be created. − th...

  • Page 132

    Das-3600 series ethernet over vdsl switch cli reference manual create vlan restrictions each vlan name can be up to 32 characters. Up to 4094 static vlans may be created per configuration. Only administrator and operator-level users can issue this command. 127.

  • Page 133

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to create a vlan v1, tag 2: 128.

  • Page 134

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#create vlan v1 tag 2 command: create vlan v1 tag 2 success. Das-3626:admin# 129.

  • Page 135

    Das-3600 series ethernet over vdsl switch cli reference manual 130

  • Page 136

    Das-3600 series ethernet over vdsl switch cli reference manual create vlan vlanid purpose used to create multiple vlans by vlan id list on the switch. Syntax create vlan vlanid { advertisement } description this command is used to create multiple vlans on the switch. Parameters − specifies a range o...

  • Page 137

    Das-3600 series ethernet over vdsl switch cli reference manual create vlan vlanid restrictions only administrator-level users can issue this command. 132.

  • Page 138

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to create a vlan id on the switch: 133.

  • Page 139

    Das-3600 series ethernet over vdsl switch cli reference manual das-3600:5#create vlan vlanid 5 advertisement command: create vlan vlanid 5 advertisement success das-3600:5# 134.

  • Page 140

    Das-3600 series ethernet over vdsl switch cli reference manual 135.

  • Page 141

    Das-3600 series ethernet over vdsl switch cli reference manual delete vlan purpose used to delete a previously configured vlan on the switch. Syntax delete vlan description this command is used to delete a previously configured vlan on the switch. Parameters − the vlan name of the vlan to delete. 13...

  • Page 142

    Das-3600 series ethernet over vdsl switch cli reference manual delete vlan restrictions only administrator and operator-level users can issue this command. 137.

  • Page 143

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to remove the vlan “v1”: das-3626:admin#delete vlan v1 command: delete vlan v1 success. Das-3626:admin# delete vlan vlanid purpose used to delete multiple vlans by vlan id on the switch. Syntax delete vlan vlanid descripti...

  • Page 144

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#config vlan v1 add tagged 4-8 command: config vlan v1 add tagged 4-8 success. Das-3626:admin# to delete ports from a vlan: das-3626:admin#config vlan v1 delete 6-8 command: config vlan v1 delete 6-8 success. Das-3626:admin...

  • Page 146

    Das-3600 series ethernet over vdsl switch cli reference manual disable gvrp purpose used to disable the generic vlan registration protocol (gvrp). Syntax disable gvrp description this command, along with enable gvrp, is used to enable and disable gvrp on the switch, without changing the gvrp configu...

  • Page 147

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show vlan command: show vlan vid : 1 vlan name : default vlan type : static advertisement : enabled member ports : 1-12 static ports : 1-12 current tagged ports : current untagged ports: 1-12 static tagged ports : static u...

  • Page 148

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show port_vlan 1-10 command: show port_vlan 1-10 global gvrp : disabled port pvid gvrp ingress checking acceptable frame type ------ ---- -------- --------------- --------------------- 1 1 disabled enabled all frames 2 1 d...

  • Page 150

    Das-3600 series ethernet over vdsl switch cli reference manual to delete protocol ipv6 from a protocol group 1: das-3626:admin#config dot1v_protocol_group group_id 1 delete protocol ethernet_2 86dd command: config dot1v_protocol_group group_id 1 delete protocol ethernet_2 86dd success. Das-3626:admi...

  • Page 152

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show port dot1v ports 1-2 command: show port dot1v ports 1-2 port : 1 protocol group id vlan name protocol priority ----------------- ---------------- ----------------- 1 default - 2 vlan_2 - 3 vlan_3 - 4 vlan_4 - port : 2...

  • Page 153

    Das-3600 series ethernet over vdsl switch cli reference manual show pvid auto_assign purpose show pvid auto-assigment state. Syntax show pvid auto_assign description this command is used to display pvid auto-assignment state. Parameters none. Restrictions none. Example usage: to display pvid auto-as...

  • Page 154

    Das-3600 series ethernet over vdsl switch cli reference manual show gvrp purpose used to display the timer’s value and nni bpdu address of gvrp. Syntax show gvrp description this command is used to display the timer’s value of gvrp. Parameters none. Restrictions none. Example usage: to display the t...

  • Page 155: -Q C

    Das-3600 series ethernet over vdsl switch cli reference manual 18 q- in -q c ommands the q-in-q commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enable qinq disable qinq show qinq create qinq spvid {tpid } dele...

  • Page 156

    Das-3600 series ethernet over vdsl switch cli reference manual enable qinq purpose used to enable q-in-q mode. Syntax enable qinq description this command enables q-in-q mode. Parameters none. Restrictions only administrator and operator-level users can issue this command. Example usage: to enable q...

  • Page 157

    Das-3600 series ethernet over vdsl switch cli reference manual show qinq purpose used to show global q-in-q. Syntax show qinq description this command is used to show the global q-in-q status. Parameters none. Restrictions none. Example usage: to show global q-in-q status: das-3626:admin#sh qinq com...

  • Page 158

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to create q-in-q: das-3626:admin#create qinq v2 spvid 2 tpid 0x88a8 command: create qinq v2 spvid 2 tpid 0x88a8 success. Das-3626:admin# delete qinq purpose used to remove q-in-q. Syntax delete qinq description this comman...

  • Page 160

    Das-3600 series ethernet over vdsl switch cli reference manual 19 l ink a ggregation c ommands the link aggregation commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create link_aggregation group_id {type [lacp ...

  • Page 161

    Das-3600 series ethernet over vdsl switch cli reference manual delete link_aggregation purpose used to delete a previously configured link aggregation group. Syntax delete link_aggregation group_id description this command is used to delete a previously configured link aggregation group. Parameters ...

  • Page 163

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show link_aggregation command: show link_aggregation link aggregation algorithm = mac-source-dest group id : 3 type : trunk master port : member port : active port : status : disabled flooding port : total entries : 1 das-...

  • Page 164

    Das-3600 series ethernet over vdsl switch cli reference manual show lacp_port purpose used to display current lacp port mode settings. Syntax show lacp_port {} description this command will display the lacp mode settings as they are currently configured. Parameters − specifies a port or range of por...

  • Page 167

    Das-3600 series ethernet over vdsl switch cli reference manual config igmp_snooping querier purpose used to configure the the time in seconds between general query transmissions, the maximum time in seconds to wait for reports from members and the permitted packet loss that guarantees igmp snooping....

  • Page 168

    Das-3600 series ethernet over vdsl switch cli reference manual config igmp_snooping querier restrictions only administrator or operator-level users can issue this command. Example usage: to configure the igmp snooping querier: das-3626:admin#config igmp_snooping querier vlan default query_interval 1...

  • Page 169

    Das-3600 series ethernet over vdsl switch cli reference manual to set up forbidden router ports: das-3626:admin#config router_ports_forbidden vlan default add 2-10 command: config router_ports_forbidden vlan default add 2-10 success. Das-3626:admin# enable igmp_snooping purpose used to enable igmp s...

  • Page 170

    Das-3600 series ethernet over vdsl switch cli reference manual show igmp_snooping configuration. − the vids of the vlan for which to view the igmp snooping configuration. Restrictions none. 165.

  • Page 171

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to show igmp snooping: das-3626:admin#show igmp_snooping command: show igmp_snooping igmp snooping global state : enabled data driven learning max entries : 128 vlan name : default query interval : 125 max response time : ...

  • Page 172

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display the router ports. Das-3626:admin#show router_ports all command: show router_ports all vlan name : default static router port : dynamic router port : router ip : forbidden router port : vlan name : v1 static rout...

  • Page 173

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to view the current igmp snooping group: das-3626:admin#show igmp_snooping group command: show igmp_snooping group source/group : null/224.1.1.1 vlan name/vid : default/1 member ports : 12 up time : 62 expiry time : 198 fi...

  • Page 176

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to view the current igmp snooping static group information: das-3626:admin#show igmp_snooping static_group command: show igmp_snooping static_group vlan id/name ip address static member ports ------------------------------...

  • Page 178

    Das-3600 series ethernet over vdsl switch cli reference manual clear igmp_snooping statistic counter purpose used to clear the current igmp snooping statistic on the switch. Syntax clear igmp_snooping statistic counter description this command is used to clear all igmp snooping statistic counters. P...

  • Page 179

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to view igmp snooping statistic on vid 1: das-3626:admin#show igmp_snooping statistic counter vlanid 1 command: show igmp_snooping statistic counter vlanid 1 vlan name : default --------------------------------------------...

  • Page 180: Igmp M

    Das-3600 series ethernet over vdsl switch cli reference manual 21 igmp m ulticast vlan c ommands the igmp multicast vlan commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create igmp_snooping multicast_vlan conf...

  • Page 181

    Das-3600 series ethernet over vdsl switch cli reference manual create igmp_snooping multicast_vlan purpose used to create an igmp multicast vlan syntax create igmp_snooping multicast_vlan . Description this command is used to create an igmp multicast_vlan. Multiple multicast vlan can be configured. ...

  • Page 182

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to configure an igmp multicast vlan: das-3626:admin#config igmp_snooping multicast_vlan v1 add member_port 1,3 state enable command: config igmp_snooping multicast_vlan v1 add member_port 1,3 state enable success. Das-3626...

  • Page 183

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to add a group to an igmp multicast vlan: das-3626:admin#config igmp_snooping multicast_vlan_group mv1 add profile_name rg command: config igmp_snooping multicast_vlan_group mv1 add profile_name rg success. Das-3626:admin#...

  • Page 184

    Das-3600 series ethernet over vdsl switch cli reference manual enable/disable igmp_snooping multicast_vlan purpose used to enable/disable the igmp multicast vlan function. Syntax enable igmp_snooping multicast_vlan disable igmp_snooping multicast_vlan description this command controls the igmp multi...

  • Page 185

    Das-3600 series ethernet over vdsl switch cli reference manual create igmp_snooping multicast_vlan_group_profile purpose used to create an igmp multicast vlan group profile on the switch. Syntax create igmp_snooping multicast_vlan_group_profile description this command is used to create an igmp mult...

  • Page 188: Mld M

    Das-3600 series ethernet over vdsl switch cli reference manual 22 mld m ulticast vlan c ommands the mld multicast vlan commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create mld_snooping multicast_vlan config ...

  • Page 189

    Das-3600 series ethernet over vdsl switch cli reference manual create mld_snooping multicast_vlan purpose used to create an mld multicast vlan syntax create mld_snooping multicast_vlan . Description this command is used to create a mld multicast_vlan. Multiple multicast vlans can be configured. The ...

  • Page 190

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to config mld multicast vlan mv1: create mld_snooping multicast_vlan_group_profile purpose used to create an mld multicast vlan group profile on the switch. Syntax create mld_snooping multicast_vlan_group_profile descripti...

  • Page 191

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to add 225.1.1.1 to 226.1.1.1 to mld multicast vlan group profile "g1": das-3626:admin#config mld_snooping multicast_vlan_group_profile g1 add ff12::1-ff12::2 command: config mld_snooping multicast_vlan_group_profile g1 ad...

  • Page 192

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display the mld multicast vlan group profile: das-3626:admin#show mld_snooping multicast_vlan_group_profile command: show mld_snooping multicast_vlan_group_profile profile name multicast addresses ----------------------...

  • Page 193

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to associate an mld multicast vlan group profile “g1” to mld multicast vlan “mv1”: das-3626:admin#config mld_snooping multicast_vlan_group mv1 add profile_name g1 command: config mld_snooping multicast_vlan_group mv1 add p...

  • Page 194

    Das-3600 series ethernet over vdsl switch cli reference manual enable/disable mld_snooping multicast_vlan purpose used to enable/disable the mld multicast vlan function. Syntax enable mld_snooping multicast_vlan disable mld_snooping multicast_vlan description this command controls the mld multicast ...

  • Page 200

    Das-3600 series ethernet over vdsl switch cli reference manual enable mld_snooping purpose used to enable mld snooping on the switch. Syntax enable mld_snooping description this command is used to enable mld snooping on the switch. Parameters none. Restrictions only administrator and operator-level ...

  • Page 201

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to show mld snooping on the switch: das-3626:admin#show mld_snooping command: show mld_snooping mld snooping global state : disabled data driven learning max entries : 128 vlan name : default query interval : 125 max respo...

  • Page 202

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to show mld snooping group on the switch: das-3626:admin#show mld_snooping group command: show mld_snooping group source/group : 2001::2/ff1e::1 vlan name/vid : default/1 member ports : 12 up time : 2 expiry time : 258 fil...

  • Page 205

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to view the current mld snooping static group information: das-3626:admin#show mld_snooping static_group command: show mld_snooping static_group vlan id/name ip address static member ports -------------------------- ------...

  • Page 208

    Das-3600 series ethernet over vdsl switch cli reference manual clear mld_snooping statistic counter purpose used to clear the current mld snooping statistic on the switch. Syntax clear mld_snooping statistic counter description this command is used to clear all mld snooping statistic counters. Param...

  • Page 210

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to add the mirroring ports: das-3626:admin#config mirror port 1 add source ports 2-5 both command: config mirror port 1 add source ports 2-5 both success. Das-3626:admin# example usage: to delete the mirroring ports: das-3...

  • Page 211

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to disable mirroring configurations: das-3626:admin#disable mirror command: disable mirror success. Das-3626:admin# show mirror purpose used to show the current port mirroring configuration on the switch. Syntax show mirro...

  • Page 212

    Das-3600 series ethernet over vdsl switch cli reference manual 25 l oop - back d etection c ommands the loop-back detection commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config loopdetect {recover_timer [val...

  • Page 214

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to disable loop-back detection on the switch: das-3626:admin#disable loopdetect command: disable loopdetect success das-3626:admin# show loopdetect purpose used to display the current loop-back detection settings on the sw...

  • Page 215

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to show loop-detect ports: das-3626:admin#show loopdetect ports 1-3 command: show loopdetect ports 1-3 port loopdetect state loop status ------ ------------------ ---------- 1 enabled normal 2 enabled normal 3 enabled norm...

  • Page 216: (Mstp) C

    Das-3600 series ethernet over vdsl switch cli reference manual 26 m ultiple s panning t ree p rotocol (mstp) c ommands this switch supports three versions of the spanning tree protocol: 802.1d-2004 stp-compatible, 802.1d-2004 rapid stp and 802.1q-2005 mstp. Multiple spanning tree protocol, or mstp, ...

  • Page 218

    Das-3600 series ethernet over vdsl switch cli reference manual command parameters show stp mst_config_id each command is listed, in detail, in the following sections. Enable stp purpose used to globally enable stp on the switch. Syntax enable stp description this command allows the spanning tree pro...

  • Page 221

    Das-3600 series ethernet over vdsl switch cli reference manual config stp ports description this command is used to create and configure stp for a group of ports. Parameters − specifies a range of ports to be configured. Externalcost − this defines a metric that indicates the relative cost of forwar...

  • Page 222

    Das-3600 series ethernet over vdsl switch cli reference manual config stp ports stp must be globally disabled and 2. Forwarding bpdu must be globally enabled. To globally disable stp, use the disable stp command, to globally enable fbpdu, use the config stp command. The default is enable. Restrictio...

  • Page 223

    Das-3600 series ethernet over vdsl switch cli reference manual 218.

  • Page 225

    Das-3600 series ethernet over vdsl switch cli reference manual config stp instance_id restrictions only administrator and operator-level users can issue this command. 220

  • Page 226

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to configure instance id 2 to add vid 10: 221.

  • Page 227

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#config stp instance_id 2 add_vlan 10 command : config stp instance_id 2 add_vlan 10 success. Das-3626:admin# 222.

  • Page 228

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to remove vid 10 from instance id 2: 223.

  • Page 229

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#config stp instance_id 2 remove_vlan 10 command : config stp instance_id 2 remove_vlan 10 success. Das-3626:admin# 224.

  • Page 230

    Das-3600 series ethernet over vdsl switch cli reference manual 225.

  • Page 231

    Das-3600 series ethernet over vdsl switch cli reference manual delete stp instance_id purpose used to delete a stp instance id from the switch. Syntax delete stp instance_id description this command allows the user to delete a previously configured stp instance id from the switch. Parameters − enter...

  • Page 232

    Das-3600 series ethernet over vdsl switch cli reference manual delete stp instance_id restrictions only administrator and operator-level users can issue this command. 227.

  • Page 233

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to delete stp instance id 2 from the switch. 228.

  • Page 234

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#delete stp instance_id 2 command: delete stp instance_id 2 success. Das-3626:admin# 229.

  • Page 235

    Das-3600 series ethernet over vdsl switch cli reference manual 230

  • Page 236

    Das-3600 series ethernet over vdsl switch cli reference manual config stp priority purpose used to configure the bridge priority. Syntax config stp priority instance_id description this command is used to update the stp instance configuration settings on the switch. The mstp will utilize the priorit...

  • Page 237

    Das-3600 series ethernet over vdsl switch cli reference manual config stp priority restrictions only administrator and operator-level users can issue this command. 232.

  • Page 238

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to set the priority value for instance_id 2 as 4096. 233.

  • Page 239

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#config stp priority 4096 instance_id 2 command : config stp priority 4096 instance_id 2 success. Das-3626:admin# 234.

  • Page 240

    Das-3600 series ethernet over vdsl switch cli reference manual 235.

  • Page 242

    Das-3600 series ethernet over vdsl switch cli reference manual config stp mst_config_id restrictions only administrator and operator-level users can issue this command. 237.

  • Page 243

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to configure the mstp region of the switch with revision_level 10 and the name “trinity”: 238.

  • Page 244

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#config stp mst_config_id revision_level 10 name trinity command : config stp mst_config_id revision_level 10 name trinity success. Das-3626:admin# 239.

  • Page 245

    Das-3600 series ethernet over vdsl switch cli reference manual 240

  • Page 247

    Das-3600 series ethernet over vdsl switch cli reference manual config stp mst_ports restrictions only administrator and operator-level users can issue this command. Example usage: to designate ports 1 through 5, with instance id 2, to have an auto internalcost and a priority of 16: das-3626:admin#co...

  • Page 248

    Das-3600 series ethernet over vdsl switch cli reference manual max hops : 20 tx hold count : 6 forwarding bpdu : disabled nni bpdu address : dot1d das-3626:admin# 243.

  • Page 249

    Das-3600 series ethernet over vdsl switch cli reference manual status 3 : stp enabled for mstp das-3626:admin#show stp command: show stp stp bridge global settings --------------------------- stp status : enabled stp version : mstp max age : 18 forward delay : 15 max hops : 15 tx hold count : 6 forw...

  • Page 250

    Das-3600 series ethernet over vdsl switch cli reference manual show stp instance_id purpose used to display the switch’s stp instance configuration syntax show stp instance_id description this command displays the switch’s current stp instance settings and the stp instance operational status. Parame...

  • Page 251

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show stp mst_config_id command: show stp mst_config_id current mst configuration identification ---------------------------------------------------------- configuration name : 00:53:13:1a:33:24 revision level :0 msti id vi...

  • Page 252

    Das-3600 series ethernet over vdsl switch cli reference manual 27 f orwarding d atabase c ommands the layer 2 forwarding database commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create fdb port create multicas...

  • Page 253

    Das-3600 series ethernet over vdsl switch cli reference manual create multicast_fdb purpose used to create a static entry to the multicast mac address forwarding table (database) syntax create multicast_fdb description this command will make an entry into the switch’s multicast mac address forwardin...

  • Page 254

    Das-3600 series ethernet over vdsl switch cli reference manual config fdb aging_time purpose used to set the aging time of the forwarding database. Syntax config fdb aging_time description this command affects the learning process of the switch. Dynamic forwarding table entries, which are made up of...

  • Page 255

    Das-3600 series ethernet over vdsl switch cli reference manual to delete a multicast fdb entry: das-3626:admin#delete fdb default 01-00-00-00-01-02 command: delete fdb default 01-00-00-00-01-02 success. Das-3626:admin# clear fdb purpose used to clear the switch’s forwarding database of all dynamical...

  • Page 256

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display multicast mac address table: 251.

  • Page 257

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show multicast_fdb vlan default command: show multicast_fdb vlan default vlan name : default mac address : 01-00-00-00-00-01 egress ports : 1-5 mode : static total entries: 1 das-3626:admin# show fdb purpose used to displa...

  • Page 259

    Das-3600 series ethernet over vdsl switch cli reference manual 28 c onnectivity f ault m anagement c ommands the connectivity fault management commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. 254.

  • Page 261

    Das-3600 series ethernet over vdsl switch cli reference manual command parameters show cfm mp_ltr_all each command is listed, in detail, in the following sections. Create cfm md purpose used to create a maintenance domain. Syntax create cfm md level description different maintenance domains should h...

  • Page 262

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to configure cfm on a maintenance domain: das-3626:admin#config cfm md op_domain mip explicit command: config cfm md op_domain mip explicit success. Das-3626:admin# create cfm ma purpose used to create a maintenance associ...

  • Page 266

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to configure the cfm mep: gs-3700-12:5#config cfm mep mepid 1 md 1 ma 1 state enable ccm enable command: config cfm mep mepid 1 md 1 ma 1 state enable ccm enable success. Das-3626:admin# delete cfm mep purpose used to dele...

  • Page 267

    Das-3600 series ethernet over vdsl switch cli reference manual delete cfm md purpose used to delete a created maintenance domain. Syntax delete cfm md description all meps and maintenance associations created in the maintenance domain will be deleted automatically. Parameters md – specifies the main...

  • Page 269

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display cfm ports: das-3626:admin#show cfm ports 3-6 command: show cfm ports 3-6 port state ----- -------- 3 enabled 4 enabled 5 enabled 6 disabled das-3626:admin# show cfm purpose this command is used to show cfm infor...

  • Page 270

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display cfm md: das-3626:admin#show cfm md op_domain command: show cfm md op_domain md level : 2 mip creation: explicit senderid tlv: none vid ma name ---- ---------- 1 op1 das-3626:admin# example usage: to display cfm ...

  • Page 271

    Das-3600 series ethernet over vdsl switch cli reference manual show cfm fault purpose this command is used to show fault meps. Syntax show cfm fault {md {ma }} description this command is used to display all the fault conditions detected by the meps contained in the specified ma or md. This display ...

  • Page 272

    Das-3600 series ethernet over vdsl switch cli reference manual show cfm mipccm purpose this command is used to show mipccm database entries. Syntax show cfm mipccm description this command is used to display all entries in the mipccm. The mipccm entry is simlar to fdb which keeps the forwarding port...

  • Page 274

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to delete a cfm linktrace: das-3626:admin#delete cfm linktrace mep mep1 command: delete cfm linktrace mep mep1 success. Das-3626:admin# config cfm ccm_fwd purpose this command is used to configure ccm pdus forwarding mode....

  • Page 276

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: the following example displays the statistics for cfm packets. Viddrop: the packets dropped due to invalid vid. Opcodrop: the packets dropped due to unrecognized cfm opcode. Das-3626:admin#show cfm counter packet command: ...

  • Page 277

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to clear the cfm packet rx/tx counters: das-3626:admin#clear cfm pkt_cnt ports 2 rx command: clear cfm pkt_cnt ports 2 rx success. Das-3600-12:4# config cfm mp_ltr_all purpose to configure the cfm mp linktrace on the switc...

  • Page 280

    Das-3600 series ethernet over vdsl switch cli reference manual show vlan_counter utilization purpose this commands displays the statistic control entries created for vlans. Syntax show vlan_counter utilization { [ vlan ] } description this commands displays the statistic control entries created for ...

  • Page 281: S C

    Das-3600 series ethernet over vdsl switch cli reference manual 30 q o s c ommands the switch supports 802.1p priority queuing. The switch has 8 priority queues. These priority queues are numbered from 7 (class 7) — the highest priority queue — to 0 (class 0) — the lowest priority queue. The eight pr...

  • Page 282

    Das-3600 series ethernet over vdsl switch cli reference manual config scheduling purpose used to configure the traffic scheduling mechanism for each cos queue. Syntax config scheduling weight description the switch contains eight hardware priority queues. Incoming packets must be mapped to one of th...

  • Page 284

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display the current scheduling configuration: das-3626:admin#show scheduling command: show scheduling qos output scheduling class id weight -------- -------- class-0 1 class-1 2 class-2 3 class-3 4 class-4 5 class-5 6 c...

  • Page 285

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show scheduling_mechanism command: show scheduling_mechanism qos scheduling_mechanism class id mechanism -------- ----------- class-0 strict class-1 strict class-2 strict class-3 strict class-4 strict class-5 strict class-...

  • Page 286

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#config 802.1p user_priority 1 3 command: config 802.1p user_priority 1 3 success. Das-3626:admin# show 802.1p user_priority purpose used to display the current mapping between an incoming packet’s 802.1p priority value and...

  • Page 287

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to configure 802.1p default priority on the switch: das-3626:admin#config 802.1p default_priority all 5 command: config 802.1p default_priority all 5 success. Das-3626:admin# show 802.1 default_priority purpose used to dis...

  • Page 288

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show 802.1p default_priority command: show 802.1p default_priority port priority effective priority ---- ----------- ------------------ 1 0 0 2 0 0 3 0 0 4 0 0 5 0 0 6 0 0 7 0 0 8 0 0 9 0 0 10 0 0 11 0 0 12 0 0 das-3626:ad...

  • Page 289

    Das-3600 series ethernet over vdsl switch cli reference manual config dscp map purpose config mapping of dscp to priority and packet’s initial color . Syntax config dscp map [dscp_priority to ] description the mapping of dscp to cos will be used to determine the priority of the packet (which will be...

  • Page 290

    Das-3600 series ethernet over vdsl switch cli reference manual 12 1 13 1 14 1 15 1 16 2 17 2 18 2 19 2 ctrl+c esc q quit space n next page enter next entry a all 285.

  • Page 291

    Das-3600 series ethernet over vdsl switch cli reference manual 31 t raffic c ontrol c ommands on a computer network, packets such as multicast packets and broadcast packets continually flood the network as normal procedure. At times, this traffic may increase do to a malicious endstation on the netw...

  • Page 292

    Das-3600 series ethernet over vdsl switch cli reference manual config traffic control purpose used to configure broadcast/multicast/unicast packet storm control. The software mechanism is provided to monitor the traffic rate in addition to the hardware storm control mechanism previously provided. Sy...

  • Page 293

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to configure traffic control and enable broadcast storm control for ports 1-12: das-3626:admin#config traffic control 1-12 broadcast enable action shutdown threshold 1 countdown 10 time_interval 10 command: config traffic ...

  • Page 295

    Das-3600 series ethernet over vdsl switch cli reference manual 32 s afeguard e ngine c ommands periodically, malicious hosts on the network will attack the switch by utilizing packet flooding (arp storm) or other methods. These attacks may increase the cpu utilization beyond its capability. To allev...

  • Page 297

    Das-3600 series ethernet over vdsl switch cli reference manual show safeguard_engine purpose used to display current safeguard engine settings. Syntax show safeguard_engine description this command is used to list the current status and type of the safeguard engine settings currently configured. Par...

  • Page 299

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#config port_security ports 1-5 admin_state enable max_learning_addr 5 lock_address_mode deleteonreset command: config port_security ports 1-5 admin_state enable max_learning_addr 5 lock_address_mode deleteonreset success. ...

  • Page 300

    Das-3600 series ethernet over vdsl switch cli reference manual show port_security purpose used to display the current port security configuration. Syntax show port_security_entry { ports } description this command is used to display port security information of the switch’s ports. The information di...

  • Page 301

    Das-3600 series ethernet over vdsl switch cli reference manual disable port_security trap_log purpose used to disable the trap/log for port security. Syntax disable port_security trap_log description this command is used to disable a port security trap/log. If the port security trap is disabled, no ...

  • Page 302: Ssl C

    Das-3600 series ethernet over vdsl switch cli reference manual 34 ssl c ommands secure sockets layer or ssl is a security feature that will provide a secure communication path between a host and client through the use of authentication, digital signatures and encryption. These security functions are...

  • Page 305

    Das-3600 series ethernet over vdsl switch cli reference manual disable ssl restrictions only administrator-level users can issue this command. Example usage: to disable the ssl status on the switch: das-3626:admin#disable ssl command: disable ssl success. Das-3626:admin# to disable ciphersuite rsa_e...

  • Page 306

    Das-3600 series ethernet over vdsl switch cli reference manual show ssl cachetimeout purpose used to show the ssl cache timeout. Syntax show ssl cachetimeout description this command is used to view the ssl cache timeout currently implemented on the switch. Parameters none. Restrictions none. Exampl...

  • Page 307

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show ssl certificate command: show ssl certificate loaded with rsa certificate! Das-3626:admin# download ssl certificate purpose used to download a certificate file for the ssl function on the switch. Syntax download ssl c...

  • Page 308: Ssh C

    Das-3600 series ethernet over vdsl switch cli reference manual 35 ssh c ommands the steps required to use the secure shell (ssh) protocol for secure communication between a remote pc (the ssh client) and the switch (the ssh server), are as follows: create a user account with admin-level access using...

  • Page 310

    Das-3600 series ethernet over vdsl switch cli reference manual command parameters show ssh algorithm 305.

  • Page 311

    Das-3600 series ethernet over vdsl switch cli reference manual each command is listed, in detail, in the following sections. 306.

  • Page 312

    Das-3600 series ethernet over vdsl switch cli reference manual enable ssh purpose used to enable ssh. Syntax enable ssh description this command allows users to enable ssh on the switch. Parameters none. 307.

  • Page 313

    Das-3600 series ethernet over vdsl switch cli reference manual enable ssh restrictions only administrator and operator-level users can issue this command. 308.

  • Page 314

    Das-3600 series ethernet over vdsl switch cli reference manual usage example: to enable ssh: 309.

  • Page 315

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#enable ssh command: enable ssh success. Das-3626:admin# 310

  • Page 316

    Das-3600 series ethernet over vdsl switch cli reference manual 311.

  • Page 317

    Das-3600 series ethernet over vdsl switch cli reference manual disable ssh purpose used to disable ssh. Syntax disable ssh description this command allows users to disable ssh on the switch. Parameters none. 312.

  • Page 318

    Das-3600 series ethernet over vdsl switch cli reference manual disable ssh restrictions only administrator and operator-level users can issue this command. 313.

  • Page 319

    Das-3600 series ethernet over vdsl switch cli reference manual usage example: to disable ssh: 314.

  • Page 320

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#disable ssh command: disable ssh success. Das-3626:admin# 315.

  • Page 321

    Das-3600 series ethernet over vdsl switch cli reference manual 316.

  • Page 323

    Das-3600 series ethernet over vdsl switch cli reference manual config ssh authmode restrictions only administrator and operator-level users can issue this command. 318.

  • Page 324

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to enable the ssh authentication mode by password: 319.

  • Page 325

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#config ssh authmode password enable command: config ssh authmode password enable success. Das-3626:admin# 320

  • Page 326

    Das-3600 series ethernet over vdsl switch cli reference manual show ssh authmode purpose used to display the ssh authentication mode settings. Syntax show ssh authmode description this command is used to display the current ssh authentication set on the switch. Parameters none. Restrictions none. Ex...

  • Page 327

    Das-3600 series ethernet over vdsl switch cli reference manual show ssh server purpose used to display the ssh server setting. Syntax show ssh server description this command is used to display the current ssh server setting. Parameters none. Restrictions none. Usage example: to display the ssh serv...

  • Page 329

    Das-3600 series ethernet over vdsl switch cli reference manual show ssh user authmode purpose used to display the ssh user setting. Syntax show ssh user authmode description this command is used to display the current ssh user setting. Parameters none. Restrictions only administrator-level users can...

  • Page 331

    Das-3600 series ethernet over vdsl switch cli reference manual show ssh algorithm purpose used to display the ssh algorithm setting. Syntax show ssh algorithm description this command is used to display the current ssh algorithm setting status. Parameters none. Restrictions none. Usage example: to d...

  • Page 332

    Das-3600 series ethernet over vdsl switch cli reference manual 36 a ccess a uthentication c ontrol c ommands the tacacs / xtacacs / tacacs+ / radius commands allows secure access to the switch using the tacacs / xtacacs / tacacs+ / radius protocols. When a user logs in to the switch or tries to acce...

  • Page 333

    Das-3600 series ethernet over vdsl switch cli reference manual the access authentication control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Note: tacacs, xtacacs and tacacs+ are separate entities and are not compatible. The...

  • Page 335

    Das-3600 series ethernet over vdsl switch cli reference manual command parameters config admin local_enable 330

  • Page 336

    Das-3600 series ethernet over vdsl switch cli reference manual each command is listed, in detail, in the following sections. 331.

  • Page 337

    Das-3600 series ethernet over vdsl switch cli reference manual enable authen_policy purpose used to enable system access authentication policy. Syntax enable authen_policy description this command will enable an administrator-defined authentication policy for users trying to access the switch. When ...

  • Page 338

    Das-3600 series ethernet over vdsl switch cli reference manual enable authen_policy restrictions only administrator-level users can issue this command. 333.

  • Page 339

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to enable the system access authentication policy: 334.

  • Page 340

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#enable authen_policy command: enable authen_policy success. Das-3626:admin# 335.

  • Page 341

    Das-3600 series ethernet over vdsl switch cli reference manual 336.

  • Page 342

    Das-3600 series ethernet over vdsl switch cli reference manual disable authen_policy purpose used to disable system access authentication policy. Syntax disable authen_policy description this command will disable the administrator-defined authentication policy for users trying to access the switch. ...

  • Page 343

    Das-3600 series ethernet over vdsl switch cli reference manual disable authen_policy restrictions only administrator-level users can issue this command. 338.

  • Page 344

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to disable the system access authentication policy: 339.

  • Page 345

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#disable authen_policy command: disable authen_policy success. Das-3626:admin# 340

  • Page 346

    Das-3600 series ethernet over vdsl switch cli reference manual 341.

  • Page 347

    Das-3600 series ethernet over vdsl switch cli reference manual show authen_policy purpose used to display the system access authentication policy status on the switch. Syntax show authen_policy description this command will show the current status of the access authentication policy on the switch. P...

  • Page 348

    Das-3600 series ethernet over vdsl switch cli reference manual show authen_policy restrictions only administrator-level users can issue this command. 343.

  • Page 349

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display the system access authentication policy: 344.

  • Page 350

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show authen_policy command: show authen_policy authentication policy: enabled das-3626:admin# 345.

  • Page 351

    Das-3600 series ethernet over vdsl switch cli reference manual 346.

  • Page 352

    Das-3600 series ethernet over vdsl switch cli reference manual create authen_login method_list_name purpose used to create a user defined method list of authentication methods for users logging on to the switch. Syntax create authen_login method_list_name description this command is used to create a...

  • Page 353

    Das-3600 series ethernet over vdsl switch cli reference manual create authen_login method_list_name restrictions only administrator-level users can issue this command. 348.

  • Page 354

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to create the method list “trinity.”: 349.

  • Page 355

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#create authen_login method_list_name trinity command: create authen_login method_list_name trinity success. Das-3626:admin# 350

  • Page 356

    Das-3600 series ethernet over vdsl switch cli reference manual 351.

  • Page 358

    Das-3600 series ethernet over vdsl switch cli reference manual config authen_login restrictions only administrator-level users can issue this command. Example usage: to configure the user defined method list “trinity” with authentication methods tacacs, xtacacs and local, in that order. Das-3626:adm...

  • Page 360

    Das-3600 series ethernet over vdsl switch cli reference manual 355.

  • Page 361

    Das-3600 series ethernet over vdsl switch cli reference manual create authen_enable method_list_name purpose used to create a user-defined method list of authentication methods for promoting normal user level privileges to administrator level privileges on the switch. Syntax create authen_enable met...

  • Page 362

    Das-3600 series ethernet over vdsl switch cli reference manual create authen_enable method_list_name restrictions only administrator-level users can issue this command. 357.

  • Page 363

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to create a user-defined method list, named “permit” for promoting user privileges to administrator privileges: 358.

  • Page 364

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#create authen_enable method_list_name permit command: create authen_enable method_list_name permit success. Das-3626:admin# 359.

  • Page 365

    Das-3600 series ethernet over vdsl switch cli reference manual 360

  • Page 367

    Das-3600 series ethernet over vdsl switch cli reference manual config authen_enable parameters default – the default method list for administration rights authentication, as defined by the user. The user may choose one or a combination of up to four (4) of the following authentication methods: • tac...

  • Page 368

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to configure the user defined method list “permit” with authentication methods tacacs, xtacacs and local, in that order. 363.

  • Page 369

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#config authen_enable method_list_name trinity method tacacs xtacacs local command: config authen_enable method_list_name trinity method tacacs xtacacs local success. Das-3626:admin# 364.

  • Page 370

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to configure the default method list with authentication methods xtacacs, tacacs+ and local, in that order: 365.

  • Page 371

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#config authen_enable default method xtacacs tacacs+ local command: config authen_enable default method xtacacs tacacs+ local success. Das-3626:admin# 366.

  • Page 372

    Das-3600 series ethernet over vdsl switch cli reference manual 367.

  • Page 373

    Das-3600 series ethernet over vdsl switch cli reference manual delete authen_enable method_list_name purpose used to delete a user-defined method list of authentication methods for promoting normal user level privileges to administrator level privileges on the switch. Syntax delete authen_enable met...

  • Page 374

    Das-3600 series ethernet over vdsl switch cli reference manual delete authen_enable method_list_name restrictions only administrator-level users can issue this command. 369.

  • Page 375

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to delete the user-defined method list “permit” 370

  • Page 376

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#delete authen_enable method_list_name permit command: delete authen_enable method_list_name permit success. Das-3626:admin# 371.

  • Page 379

    Das-3600 series ethernet over vdsl switch cli reference manual application login method list enable method list -------------- ---------------- ----------------------- console default default telnet trinity default ssh default default http default default das-3626:admin# create authen server_host pu...

  • Page 382

    Das-3600 series ethernet over vdsl switch cli reference manual delete authen server_host restrictions only administrator-level users can issue this command. Example usage: to delete a user-defined tacacs+ authentication server host: das-3626:admin#delete authen server_host 10.1.1.121 protocol tacacs...

  • Page 383

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show authen server_host command: show authen server_host ip address protocol port timeout retransmit key ----------- -------- ----- ------- ---------- ----- 10.53.13.94 tacacs 49 5 2 no use total entries : 1 das-3626:admin...

  • Page 385

    Das-3600 series ethernet over vdsl switch cli reference manual delete authen server_group purpose used to delete a user-defined authentication server group. Syntax delete authen server_group description this command will delete an authentication server group. Parameters − enter an alphanumeric strin...

  • Page 386

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to view authentication server groups currently set on the switch. Das-3626:admin#show authen server_group command: show authen server_group server group : mix_1 group name ip address protocol --------------- --------------...

  • Page 387

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to set the maximum number of authentication attempts at 5: 382.

  • Page 388

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin# config authen parameter attempt 5 command: config authen parameter attempt 5 success. Das-3626:admin# 383.

  • Page 389

    Das-3600 series ethernet over vdsl switch cli reference manual 384.

  • Page 390

    Das-3600 series ethernet over vdsl switch cli reference manual show authen parameter purpose used to display the authentication parameters currently configured on the switch. Syntax show authen parameter description this command will display the authentication parameters currently configured on the ...

  • Page 391

    Das-3600 series ethernet over vdsl switch cli reference manual show authen parameter restrictions only administrator-level users can issue this command. 386.

  • Page 392

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to view the authentication parameters currently set on the switch: 387.

  • Page 393

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show authen parameter command: show authen parameter response timeout : 30 seconds user attempts : 3 das-3626:admin# 388.

  • Page 394

    Das-3600 series ethernet over vdsl switch cli reference manual 389.

  • Page 395

    Das-3600 series ethernet over vdsl switch cli reference manual enable admin purpose used to promote user level privileges to administrator level privileges. Syntax enable admin description this command is for users who have logged on to the switch on the normal user level, to become promoted to the ...

  • Page 396

    Das-3600 series ethernet over vdsl switch cli reference manual 391.

  • Page 397: (Dhcp S

    Das-3600 series ethernet over vdsl switch cli reference manual 37 f ilter c ommands (dhcp s erver /n et bios) dhcp server screening settings this function allows you not only to restrict all dhcp server packets but also to receive any specified dhcp server packets by any specified dhcp client, it is...

  • Page 398

    Das-3600 series ethernet over vdsl switch cli reference manual config filter dhcp_server purpose dhcp server packets except those that have been ip/client mac bound will be filtered. This command is used to configure the state of the function for filtering of dhcp server packet and to add/delete the...

  • Page 399

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display the dhcp server filter list created on the switch: das-3626:admin#show filter dhcp_server command: show filter dhcp_server enabled ports: 1-3 filter dhcp server/client table server ip address client mac address ...

  • Page 400

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display the extensive netbios filter status: das-3626:admin#show filter netbios command: show filter netbios enabled ports: 1-3 das-3626:admin# config filter extensive_netbios purpose used to configure the switch to fil...

  • Page 401: (Acl) C

    Das-3600 series ethernet over vdsl switch cli reference manual 38 a ccess c ontrol l ist (acl) c ommands the switch implements access control lists that enable the switch to deny network access to specific devices or device groups based on ip settings and mac address. The access profile commands in ...

  • Page 403

    Das-3600 series ethernet over vdsl switch cli reference manual the deny parameter instructs the switch to filter any frames that meet the criteria − in this case, when a logical and operation between an ip address specified in the next step and the ip_source_mask match. The default for an access pro...

  • Page 404

    Das-3600 series ethernet over vdsl switch cli reference manual create access_profile parameters profile_id − sets the relative priority for the profile. Priority is set relative to other profiles where the lowest profile id has the highest priority. The user may enter a profile id number between 1 -...

  • Page 407

    Das-3600 series ethernet over vdsl switch cli reference manual config access_profile purpose used to configure an access profile on the switch and to define specific values that will be used to by the switch to determine if a given packet should be forwarded or filtered. Masks entered using the crea...

  • Page 408

    Das-3600 series ethernet over vdsl switch cli reference manual config access_profile parameters profile_id − enter an integer used to identify the access profile that will be configured with this command. This value is assigned to the access profile when it is created with the create access_profile ...

  • Page 413

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show time_range command: show time_range time range information ------------------------- range name : 1-3_new weekdays : mon,tue,wed,thu,fri start time : 11:21:20 end time : 11:44:40 total entries :1 das-3626:admin# show ...

  • Page 414

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show current_config access_profile command: show current_config access_profile #---------------------------------------------------------------------- # acl create access_profile profile_id 1 profile_name rg ethernet vlan ...

  • Page 415: Vdsl C

    Das-3600 series ethernet over vdsl switch cli reference manual 39 vdsl c ommands the vdsl switch commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. 410

  • Page 422

    Das-3600 series ethernet over vdsl switch cli reference manual show vdsl line restrictions only administrator-level users or operation-level can issue this command. 417.

  • Page 423

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: show vdsl line bit map 418.

  • Page 424

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show vdsl line 24 bit_map show vdsl line 24 bit_map --- bitmap --- line24 ( 0 ) 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 ( 16 ) 0, 0, 0, 3, 4, 4, 4, 4, 4, 4, 5, 5, 5, 5, 6, 5 ( 32 ) 6, 6, 6, 0, 6, 6, 6, 6, 6, 6, 6, 6...

  • Page 425

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: show vdsl line status das-3626:admin#show vdsl line 24 status show vdsl line 24 status line24 : vdsl24 link state : showtime line type : interleaved line uptime : 0 days 20 hours 25 minutes 24 seconds band plan : itu annex...

  • Page 428

    Das-3600 series ethernet over vdsl switch cli reference manual show vdsl pm_threshold purpose used to show vdsl performance counter threshold. Syntax show vdsl pm_threshold description this command is used to shwo vdsl performance counter threshold. Parameters restrictions only administrator-level u...

  • Page 445

    Das-3600 series ethernet over vdsl switch cli reference manual 40 n etwork m onitoring c ommands the network monitoring commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters show packet ports show error ports show u...

  • Page 446

    Das-3600 series ethernet over vdsl switch cli reference manual show packet ports purpose used to display statistics about the packets sent and received by the switch. Syntax show packet ports description this command is used to display statistics about packets sent and received by ports specified in...

  • Page 447

    Das-3600 series ethernet over vdsl switch cli reference manual show packet ports restrictions none. 442.

  • Page 448

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display the packets analysis for port 2: 443.

  • Page 449

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show packet port 2 command: show packet port 2 port number : 2 ================================================================== frame size/type frame counts frames/sec --------------- ---------------------- ----------- 6...

  • Page 450

    Das-3600 series ethernet over vdsl switch cli reference manual 445.

  • Page 451

    Das-3600 series ethernet over vdsl switch cli reference manual show error ports purpose used to display the error statistics for a range of ports. Syntax show error ports description this command will display all of the packet error statistics collected and logged by the switch for a given port list...

  • Page 452

    Das-3600 series ethernet over vdsl switch cli reference manual show error ports restrictions none. 447.

  • Page 453

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to display the errors of the port 3: 448.

  • Page 454

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show error ports 3 command: show error ports 3 port number : 3 rx frames tx frames --------- --------- crc error 0 excessive deferral 0 undersize 0 crc error 0 oversize 0 late collision 0 fragment 0 excessive collision 0 j...

  • Page 455

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#show utilization cpu command: show utilization cpu cpu utilization ----------------------------------------------------------------- five seconds - 9 % one minute - 10 % five minutes - 10 % das-3626:admin# show utilization...

  • Page 456

    Das-3600 series ethernet over vdsl switch cli reference manual clear counters purpose used to clear the switch’s statistics counters. Syntax clear counters {ports } description this command will clear the counters used by the switch to compile statistics. Parameters − specifies a port or range of po...

  • Page 457

    Das-3600 series ethernet over vdsl switch cli reference manual clear counters restrictions only administrator and operator-level users can issue this command. 452.

  • Page 458

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to clear the counters: 453.

  • Page 459

    Das-3600 series ethernet over vdsl switch cli reference manual das-3626:admin#clear counters ports 2-9 command: clear counters ports 2-9 success. Das-3626:admin# 454.

  • Page 460

    Das-3600 series ethernet over vdsl switch cli reference manual clear log purpose used to clear the switch’s history log. Syntax clear log description this command is used to clear the switch’s history log. Parameters none. Restrictions only administrator and operator-level users can issue this comma...

  • Page 461

    Das-3600 series ethernet over vdsl switch cli reference manual note: for detailed information regarding log entries that will appear in this window, please refer to appendix c at the back of the das-3600- 12 layer 2 gigabit ethernet managed switch user manual. Enable syslog purpose used to enable th...

  • Page 462

    Das-3600 series ethernet over vdsl switch cli reference manual show syslog purpose used to display the syslog protocol status as enabled or disabled. Syntax show syslog description this command is used to display the syslog status as enabled or disabled. Parameters none. Restrictions none. Example u...

  • Page 463

    Das-3600 series ethernet over vdsl switch cli reference manual create syslog host 0 kernel messages 1 user-level messages 2 mail system 3 system daemons 4 security/authorization messages 5 messages generated internally by syslog 6 line printer subsystem 7 network news subsystem 8 uucp subsystem 9 cl...

  • Page 464

    Das-3600 series ethernet over vdsl switch cli reference manual to create a syslog host: das-3626:admin#create syslog host 1 severity all facility local0 ipaddress 1.1.1.1 command: create syslog host 1 severity all facility local0 ipaddress 1.1.1.1 success. Das-3626:admin# config syslog host purpose ...

  • Page 465

    Das-3600 series ethernet over vdsl switch cli reference manual config syslog host 0 kernel messages 1 user-level messages 2 mail system 3 system daemons 4 security/authorization messages 5 messages generated internally by syslog 6 line printer subsystem 7 network news subsystem 8 uucp subsystem 9 cl...

  • Page 466

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to configure a syslog host: das-3626:admin#config syslog host 1 severity all command: config syslog host 1 severity all success. Das-3626:admin# example usage: to configure a syslog host for all hosts: das-3626:admin#confi...

  • Page 467

    Das-3600 series ethernet over vdsl switch cli reference manual to show syslog host information: das-3626:admin#show syslog host command: show syslog host syslog global state: disabled host id host ip address severity facility udp port status ------- --------------- ---------- -------- -------- -----...

  • Page 468

    Das-3600 series ethernet over vdsl switch cli reference manual to show log_save_timing: das-3626:admin#show log_save_timing command: show log_save_timing saving log method: on_demand das-3626:admin# show attack_log purpose used to show dangerous log messages. Syntax show attack_log {index } descript...

  • Page 470

    Das-3600 series ethernet over vdsl switch cli reference manual example usage: to configure the system severity settings: das-3626:admin#config system_severity trap critical command: config system_severity trap critical success. Das-3626:admin# show system_severity purpose to display system_severity ...

  • Page 471

    Das-3600 series ethernet over vdsl switch cli reference manual 41 p assword r ecovery c ommand l ist the switch password recovery commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters reset config {force_agree} rebo...

  • Page 472

    Das-3600 series ethernet over vdsl switch cli reference manual reset config purpose used to reset the configuration . Syntax reset config { force_agree } description this command is used to reset the configuration parameters. The configuration is reset but not saved. Parameters force_agree: if this ...

  • Page 473

    Das-3600 series ethernet over vdsl switch cli reference manual reset account purpose used to delete the created account. Syntax reset account description this command is used to delete all of the created user accounts. The banner messages for password recover mode is: password recovery mode paramete...

  • Page 474

    Das-3600 series ethernet over vdsl switch cli reference manual show account purpose used to show the created account. Syntax show account description this command is used to display all already created accounts. Parameters none. Restrictions none. Example usage: to view the created account: >show ac...

  • Page 475

    Das-3600 series ethernet over vdsl switch cli reference manual 42 c ommand h istory l ist the switch history commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters ? Config command_history show command_history each c...

  • Page 476

    Das-3600 series ethernet over vdsl switch cli reference manual ? Purpose used to display all commands in the command line interface (cli). Syntax ? {} description this command will display all of the commands available through the command line interface (cli). Parameters {} – entering the question m...

  • Page 478

    Das-3600 series ethernet over vdsl switch cli reference manual show command_history purpose used to display the command history. Syntax show command_history description this command is used to display currently used command history. Parameters none. Restrictions none. Example usage: to display the c...

  • Page 479: Appendix A

    Das-3600 series ethernet over vdsl switch cli reference manual appendix a p assword r ecovery p rocedure this section describes the procedure for resetting passwords on d-link switches. Authenticating any user who tries to access networks is necessary and important. The basic authentication method u...

  • Page 480

    Das-3600 series ethernet over vdsl switch cli reference manual command parameters reset config this command resets the whole configuration will be back to the default value reboot this command exits the reset password recovery mode and restarts the switch. A confirmation message will be displayed to...