1. DL manuals
  2. D-Link
  3. Switch
  4. DES-1008P
  5. User Manual

D-Link DES-1008P User Manual

Manual is about: 8-PORT 10/100Mbps ETHERNET SWITCH WITH 4 PoE PORTS

Summary of DES-1008P

  • Page 1

    D-link des-1008p 8-port 10/100mbps with 4 poe ports switch user guide.

  • Page 2: Fcc Warning

    Fcc warning this equipment has been tested and found to comply with the regulations for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. ...

  • Page 3: Ul Warning

    Ul warning a) elevated operating ambient temperature- if installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible wi...

  • Page 4: Table of Contents

    I table of contents about this guide................................................................................. 1 purpose ............................................................................................ 1 terms/usage ....................................................................

  • Page 5: About This Guide

    1 about this guide congratulations on your purchase of the d-link des-1008p, an 8- port 10/100mbps fast ethernet switch with 4-port poe. This switch integrates 100mbps fast ethernet and 10mbps ethernet network capabilities in a highly flexible package. Port-1 to port-4 on the switch support power ov...

  • Page 6: Introduction

    2 introduction this chapter describes the features of the d-link des-1008p fast ethernet poe switch and some background information about ethernet/fast ethernet, switching and power over ethernet technology. Fast ethernet technology the growing importance of lans and the increasing complexity of des...

  • Page 7

    3 switching technology another approach to pushing beyond the limits of ethernet technology is the development of switching technology. A switch bridges ethernet packets at the mac address level of the ethernet protocol transmitting among connected ethernet or fast ethernet lan segments. Switching i...

  • Page 8

    4 power over ethernet (poe) power over ethernet (poe) integrates power and data onto one single cabling infrastructure, eliminating the need to have ac power available at all locations. Power and data is integrated onto the same cable, supporting category 5/5e up to 100 meters. Poe will provide powe...

  • Page 9: Unpacking and Installation

    5 unpacking and installation this chapter provides unpacking and installation information for the switch. Unpacking open the shipping cartons of the switch and carefully unpack its contents. The carton should contain the following items: one des-1008p one ac power adapter four rubber feet cd-rom wit...

  • Page 10

    6 connecting network cable the switch support 8 10/100mbps ethernet ports and port 1 ~ port 4 are poe enabled ports, these poe port will automatically activate when a compatible terminal is identified. The switch will supply power through the ethernet port to the connected poe powered device (pd). F...

  • Page 11: Led Indicator:

    7 identifying external components this chapter describes the front panel, rear panel, and led indicators of the switch. Front panel the figure below shows the front panels of the switch. Figure 1. Front panel led indicator: comprehensive led indicators display the status of the switch and the networ...

  • Page 12: Ethernet Ports (Port 5~8):

    8 these ports support network speeds of either 10mbps or 100mbps, and can operate in half- and full- duplex transfer modes. These ports also support automatic mdi/mdix crossover detection, which gives the switch true, “plug and play” capabilities. Just connect any network cable between the switch an...

  • Page 13

    9 understanding led indicators the front panel leds provides instant status feedback, and helps monitor and troubleshoot when needed. Figure 3. Led indicators of the switch system led pwr: (power indicator) on : power on off : power off poe status leds (port 1 ~ port 4) poe status: green : when the ...

  • Page 14

    1 0 poe max on : when the power output to pds has reached or exceeded the maximum power budget. No additional pds connected will be powered. Off : when the system is using less than 46w blinking when the system power usage is >=56w ethernet port status leds (ports 1~8) 10/100m link/act: 10m : when t...

  • Page 15

    1 1 for example: there are poe pds connected to the poe switch and the total power consumption is 48 watts. The system will reserve 8 watts for a buffer and the poe max led will light up. Once there is another poe pd inserted, the system will not provide power to the additional poe pd. Priority: thi...

  • Page 16: Technical Specifications

    1 2 technical specifications general standards ieee 802.3 10base-t ethernet ieee 802.3u 100base-tx fast ethernet ieee 802.3x full duplex flow control ieee 802.3af power over ethernet protocol csma/cd data transfer rate ethernet: 10mbps (half duplex), 20mbps (full-duplex) fast ethernet: 100mbps (half...

  • Page 17: Performance

    1 3 performance ram buffer: 96k bytes per device filtering address table: 1k entries per device packet filtering/forwarding rate: 10mbps ethernet: 14,880/pps 100mbps fast ethernet: 148,800/pps mac address learning: automatic update transmits method: store-and-forward.