- DL manuals
- D-Link
- Switch
- DES-3326S - Switch - Stackable
- Command Line Interface Reference Manual
D-Link DES-3326S - Switch - Stackable Command Line Interface Reference Manual
Summary of DES-3326S - Switch - Stackable
Page 1
Des-3326s stackable layer 3 switch command line interface reference manual may 2005 651e3326055.
Page 3
D-link des-3326s layer 3 switch cli reference trademarks copyright 2005 d-link corporation. Contents subject to change without prior notice. D-link is a registered trademark of d-link corporation/d-link systems, inc. All other trademarks belong to their respective proprietors. Copyright statement n...
Page 5
Table of contents introduction............................................................................................................................................................. 1 using the console cli............................................................................................
Page 6
Glossary .............................................................................................................................................................. 312.
Page 7
D-link des-3326s layer 3 switch cli reference 1 i ntroduction the switch can be managed through the switch’s serial port, telnet, or the web-based management agent. The command line interface (cli) can be used to configure and manage the switch via the serial port or telnet interfaces. This manual p...
Page 8
D-link des-3326s layer 3 switch cli reference setting the switch’s ip address each switch must be assigned its own ip address, which is used for communication with an snmp network manager or other tcp/ip application (for example bootp, tftp). The switch’s default ip address is 10.90.90.90. You can c...
Page 9
D-link des-3326s layer 3 switch cli reference figure 1-3. Assigning the switch an ip address in the above example, the switch was assigned an ip address of 10.41.44.33 with a subnet mask of 255.0.0.0. The system message success indicates that the command was executed successfully. The switch can now...
Page 10: Cli
D-link des-3326s layer 3 switch cli reference 2 u sing the c onsole cli the des-3326s supports a console management interface that allows the user to connect to the switch’s management agent via a serial port and a terminal or a computer running a terminal emulation program. The console can also be ...
Page 11
D-link des-3326s layer 3 switch cli reference after the switch reboots and you have logged in, the console looks like this: figure 2-1. Initial console screen commands are entered at the command prompt, des-3326s:4#. There are a number of helpful features included in the cli. Entering the ? Command ...
Page 12
D-link des-3326s layer 3 switch cli reference figure 2-3. Example command parameter help in this case, the command config account was entered with the parameter . The cli will then prompt you to enter the with the message, next possible completions:. Every command in the cli has this feature, and co...
Page 13
D-link des-3326s layer 3 switch cli reference all commands in the cli function in this way. In addition, the syntax of the help prompts are the same as presented in this manual − angle brackets indicate a numerical value or character string, braces { } indicate optional parameters or a choice of par...
Page 14
D-link des-3326s layer 3 switch cli reference 3 c ommand s yntax the following symbols are used to describe how command entries are made and values and arguments are specified in this manual. The online help contained in the cli and available through the console interface uses the same syntax. Note:...
Page 15
D-link des-3326s layer 3 switch cli reference purpose encloses a variable or value that must be specified. Syntax create ipif vlan ipaddress description in the above syntax example, you must supply an ip interface name in the space, a vlan name in the space, and the network address in the space. Do ...
Page 17
D-link des-3326s layer 3 switch cli reference line editing key usage delete deletes the character under the cursor and then shifts the remaining characters in the line to the left. Backspace deletes the character to the left of the cursor and shifts the remaining characters in the line to the left. ...
Page 20
D-link des-3326s layer 3 switch cli reference config account purpose used to configure user accounts syntax config account description the config account command configures a user account that has been created using the create account command. Parameters restrictions only administrator-level users c...
Page 21
D-link des-3326s layer 3 switch cli reference show account purpose used to display user accounts syntax show account description displays all user accounts created on the switch. Up to 8 user accounts can exist on the switch at one time. Parameters none. Restrictions none. Example usage: to display ...
Page 22
D-link des-3326s layer 3 switch cli reference delete account purpose used to delete an existing user account syntax delete account description the delete account command deletes a user account that has been created using the create account command. Parameters restrictions only administrator-level us...
Page 23
D-link des-3326s layer 3 switch cli reference show session purpose used to display a list of currently logged-in users. Syntax show session description this command displays a list of all the users that are logged-in at the time the command is issued. Parameters none restrictions none. Example usage...
Page 24
D-link des-3326s layer 3 switch cli reference show serial_port purpose used to display the current serial port settings. Syntax show serial_port description this command displays the current serial port settings. Parameters none. Restrictions none example usage: to display the serial port setting: d...
Page 25
D-link des-3326s layer 3 switch cli reference show switch purpose used to display information about the switch. Syntax show switch description this command displays information about the switch. Parameters none. Restrictions none. Example usage: to display the switch information: des-3326s:4#show sw...
Page 26
D-link des-3326s layer 3 switch cli reference show serial_port purpose used to display the current serial port settings. Syntax show serial_port description this command displays the current serial port settings. Parameters none. Restrictions none example usage: to display the serial port setting: d...
Page 28
D-link des-3326s layer 3 switch cli reference enable clipaging purpose used to pause the scrolling of the console screen when the show command displays more than one page. Syntax enable clipaging description this command is used when issuing the show command will cause the console screen to rapidly ...
Page 29
D-link des-3326s layer 3 switch cli reference disable clipaging purpose used to disable the pausing of the console screen scrolling at the end of each page when the show command would display more than one screen of information. Syntax disable clipaging description this command is used to disable th...
Page 30
D-link des-3326s layer 3 switch cli reference enable telnet purpose used to enable communication with and management of the switch using the telnet protocol. Syntax enable telnet description this command is used to enable the telnet protocol on the switch. The user can specify the tcp or udp port nu...
Page 31
D-link des-3326s layer 3 switch cli reference disable telnet purpose used to disable the telnet protocol on the switch. Syntax disable telnet description this command is used to disable the telnet protocol on the switch. Parameters none. Restrictions only administrator-level users can issue this com...
Page 32
D-link des-3326s layer 3 switch cli reference enable web purpose used to enable the http-based management software on the switch. Syntax enable web description this command is used to enable the web- based management software on the switch. The user can specify the tcp port number the switch will us...
Page 33
D-link des-3326s layer 3 switch cli reference disable web purpose used to disable the http-based management software on the switch. Syntax disable web description this command disables the web-based management software on the switch. Parameters none. Restrictions only administrator-level users can i...
Page 34
D-link des-3326s layer 3 switch cli reference save purpose used to save changes in the switch’s configuration to non-volatile ram. Syntax save description this command is used to enter the current switch configuration into non-volatile ram. The saved switch configuration will be loaded into the swit...
Page 35
D-link des-3326s layer 3 switch cli reference reboot purpose used to restart the switch. Syntax reboot description this command is used to restart the switch. Parameters none. Restrictions none. Example usage: to restart the switch: des-3326s:4#reboot command: reboot are you sure you want to proceed...
Page 37
D-link des-3326s layer 3 switch cli reference login purpose used to log in a user to the switch’s console. Syntax login description this command is used to initiate the login procedure. The user will be prompted for his username and password. Parameters none. Restrictions none. Example usage: to ini...
Page 40
D-link des-3326s layer 3 switch cli reference show ports purpose used to display the current configuration of a range of ports. Syntax show ports {} description this command is used to display the current configuration of a range of ports. Parameters − specifies a range of ports to be configured. Th...
Page 43
D-link des-3326s layer 3 switch cli reference example usage: to configure the port lock for ports 1:12 – 1:14 to delete the dynamic address table entries on timeout: des-3326s:4#config port_security ports 12-14 lock_address_mode deleteontimeout command: config port_security ports 12-14 lock_address_...
Page 44
D-link des-3326s layer 3 switch cli reference config port_security_entry purpose used to clear the mac entries learned from the specified port(s) for the port security function syntax clear port_security_entry port description this will delete all entries from the forwarding data base for a specific...
Page 45
D-link des-3326s layer 3 switch cli reference show port_security purpose used to display the current portr lock configuration. Syntax show port_security {} description this command is used to display the current port lock configuration of a range of ports. Parameters − specifies a range of ports to ...
Page 46
D-link des-3326s layer 3 switch cli reference 7 n etwork m anagement c ommands the network management commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. The des-3326s supports the simple network management protocol (snmp) versions ...
Page 50
D-link des-3326s layer 3 switch cli reference example usage: to create an snmp user on the switch: des-3326s:4#create snmp user dlink default v3 encrypted auth md5 auth_password priv none command: create snmp user dlink default v3 encrypted auth md5 auth_password priv none success. Des-3326s:4# dele...
Page 51
D-link des-3326s layer 3 switch cli reference example usage: to delete a previously entered snmp user on the switch: des-3326s:4#delete snmp user dlink command: delete snmp user dlink success. Des-3326s:4# show snmp user purpose used to display information about each snmp username in the snmp group ...
Page 52
D-link des-3326s layer 3 switch cli reference show snmp groups purpose used to display the group-names of snmp groups currently configured on the switch. The security model, level, and status of each group is also displayed. Syntax show snmp groups description the show snmp groups command displays t...
Page 53
D-link des-3326s layer 3 switch cli reference group name : group6 readview name : readview writeview name : writeview notify view name : notifyview securiy model : snmpv3 securiy level : authpriv group name : group7 readview name : readview writeview name : writeview notify view name : notifyview se...
Page 54
D-link des-3326s layer 3 switch cli reference group name : readgroup readview name : communityview writeview name : notify view name : communityview securiy model : snmpv2 securiy level : noauthnopriv group name : writegroup readview name : communityview writeview name : communityview notify view na...
Page 57
D-link des-3326s layer 3 switch cli reference show snmp view purpose used to display an snmp view previously created on the switch. Syntax show snmp view {} description the show snmp view command displays an snmp view previously created on the switch. Parameters − an alphanumeric string of up to 32 ...
Page 58
D-link des-3326s layer 3 switch cli reference create snmp community purpose used to create an snmp community string to define the relationship between the snmp manager and an agent. The community string acts like a password to permit access to the agent on the switch. One or more of the following ch...
Page 59
D-link des-3326s layer 3 switch cli reference delete snmp community purpose used to remove a specific snmp community string from the switch. Syntax delete snmp community 32> description the delete snmp community command is used to remove a previously defined snmp community string from the switch. Pa...
Page 60
D-link des-3326s layer 3 switch cli reference show snmp community purpose used to display snmp community strings configured on the switch. Syntax show snmp community { 32>} description the show snmp community command is used to display snmp community strings that are configured on the switch. Parame...
Page 61
D-link des-3326s layer 3 switch cli reference config snmp engineid purpose used to configure a name for the snmp engine on the switch. Syntax config snmp engineid description the config snmp engineid command configures a name for the snmp engine on the switch. Parameters − an alphanumeric string tha...
Page 63
D-link des-3326s layer 3 switch cli reference example usage: to create an snmp group named “sg1:” des-3326s:4#create snmp group sg1 v3 noauth_nopriv read_view v1 write_view v1 notify_view v1 command: create snmp group sg1 v3 noauth_nopriv read_view v1 write_view v1 notify_view v1 success. Des-3326s:...
Page 64
D-link des-3326s layer 3 switch cli reference example usage: to delete the snmp group named “sg1”. Des-3326s:4#delete snmp group sg1 command: delete snmp group sg1 success. Des-3326s:4# show snmp host purpose used to display the recipient of snmp traps generated by the switch’s snmp agent. Syntax sh...
Page 66
D-link des-3326s layer 3 switch cli reference delete snmp host purpose used to remove a recipient of snmp traps generated by the switch’s snmp agent. Syntax delete snmp host description the delete snmp host command deletes a recipient of snmp traps generated by the switch’s snmp agent. Parameters − ...
Page 67
D-link des-3326s layer 3 switch cli reference show snmp host purpose used to display the recipient of snmp traps generated by the switch’s snmp agent. Syntax show snmp host {} description the show snmp host command is used to display the ip addresses and configuration information of remote snmp mana...
Page 68
D-link des-3326s layer 3 switch cli reference enable rmon purpose used to enable rmon on the switch. Syntax enable rmon description this command is used, in conjunction with the disable rmon command below, to enable and disable remote monitoring (rmon) on the switch. Parameters none. Restrictions on...
Page 69
D-link des-3326s layer 3 switch cli reference disable rmon purpose used to disable rmon on the switch. Syntax disable rmon description this command is used, in conjunction with the enable rmon command above, to enable and disable remote monitoring (rmon) on the switch. Parameters none. Restrictions ...
Page 70
D-link des-3326s layer 3 switch cli reference ping purpose used to test the connectivity between network devices. Syntax ping {times } {timeout } description this command sends internet control message protocol (icmp) echo messages to a remote ip address. The remote ip address will then “echo” or re...
Page 71
D-link des-3326s layer 3 switch cli reference traceroute purpose used to determine the network path between two devices. Syntax traceroute {ttl } {port } {timeout >} {probe } description this command allows you to trace a route between the switch and a give host on the network. Parameters − the ip a...
Page 74
D-link des-3326s layer 3 switch cli reference enable mac_notification purpose used to globally enable mac address notification without changing the mac_notification configuration. Syntax enable mac_notification description enables mac notication on the switch. Parameters none. Restrictions only admi...
Page 75
D-link des-3326s layer 3 switch cli reference show mac_notification purpose used to display mac address notification. Syntax show mac_notification {ports} description displays mac notification settings either per port or globally as desired. Parameters none – this will display global mac notificatio...
Page 76
D-link des-3326s layer 3 switch cli reference example usage: to display per port mac notification settings: des-3326s:4#show mac_notification ports command: show mac_notification ports port # mac address table notification state ------ ------------------ ----------- ------- 1 enabled 2 enabled 3 ena...
Page 80
D-link des-3326s layer 3 switch cli reference 10 n etwork m onitoring c ommands the network monitoring commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters show packet ports show error ports show utilitzation clear...
Page 82
D-link des-3326s layer 3 switch cli reference show packet ports purpose used to display statistics about the packets sent and received by the switch. Syntax show packet ports description this command is used to display statistics about packets sent and received by ports specified in the port list. P...
Page 83
D-link des-3326s layer 3 switch cli reference show error ports purpose used to display the error statistics for a range of ports. Syntax show error ports description this command will display all of the packet error statistics collected and logged by the swtich for a given port list. Parameters − sp...
Page 84
D-link des-3326s layer 3 switch cli reference show utilization purpose used to display real-time port utilization statistics. Syntax show utilization description this command will display the real-time port utilization statistics for the switch. Parameters none. Restrictions none. Example usage: to ...
Page 85
D-link des-3326s layer 3 switch cli reference clear counters purpose used to clear the switch’s statistics counters. Syntax clear counters {ports } description this command will clear the counters used by the switch to compile statistics. Parameters − specifies a range of ports to be configured. The...
Page 86
D-link des-3326s layer 3 switch cli reference clear log purpose used to clear the switch’s history log. Syntax clear log description this command will clear the switch’s history log. Parameters none. Restrictions only administrator-level users can issue this command. Example usage: to clear the log ...
Page 87
D-link des-3326s layer 3 switch cli reference show log purpose used to display the switch history log. Syntax show log {index } description this command will display the contents of the switch’s history log. Parameters index − the show log command will display the history log until the log number re...
Page 88
D-link des-3326s layer 3 switch cli reference enable syslog purpose used to enable the system log to be sent to a remote host. Syntax enable syslog description the enable syslog command enables the system log to be sent to a remote host. Parameters none. Restrictions only administrator-level users c...
Page 89
D-link des-3326s layer 3 switch cli reference disable syslog purpose used to enable the system log to be sent to a remote host. Syntax disable syslog description the disable syslog command disables the system log to be sent to a remote host. Parameters none. Restrictions only administrator-level use...
Page 90
D-link des-3326s layer 3 switch cli reference show syslog purpose used to display the syslog protocol status as enable or disabled. Syntax show syslog description the show syslog command displays the syslog status as enabled or disabled. Parameters none. Restrictions none. Example usage: to display ...
Page 93
D-link des-3326s layer 3 switch cli reference create syslog host parameters local0 − specifies that local use 0 messages will be sent to the remote host. This corresponds to number 16 from the list above. Local1 − specifies that local use 1 messages will be sent to the remote host. This corresponds ...
Page 95
D-link des-3326s layer 3 switch cli reference config syslog host parameters informational − specifies that informational messages will be sent to the remote host. This corresponds to number 6 from the list above. Warning − specifies that warning messages will be sent to the remote host. This corresp...
Page 96
D-link des-3326s layer 3 switch cli reference config syslog host parameters parameters 16 local use 0 (local0) 17 local use 1 (local1) 18 local use 2 (local2) 19 local use 3 (local3) 20 local use 4 (local4) 21 local use 5 (local5) 22 local use 6 (local6) 23 local use 7 (local7) local0 − specifies th...
Page 98
D-link des-3326s layer 3 switch cli reference show syslog host purpose used to display the syslog hosts currently configured on the switch. Syntax show syslog host {} description the show syslog host command is used to display the syslog hosts that are currently configured on the switch. Parameters ...
Page 99
D-link des-3326s layer 3 switch cli reference 11 s panning t ree c ommands the switch supports 802.1w rapid stp and 802.1d stp. The spanning tree commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config stp maxa...
Page 102
D-link des-3326s layer 3 switch cli reference example usage: to configure stp with path cost 19, priority 15, and state enabled for ports 1-5 of module 1. Des-3326s:4#config stp ports 1:1-1:5 cost 19 priority 15 state enable command: config stp ports 1-5 cost 19 priority 15 state enable success. Des...
Page 103
D-link des-3326s layer 3 switch cli reference disable stp purpose used to globally disable stp on the switch. Syntax disable stp description this command allows the spanning tree protocol to be globally disabled on the switch. Parameters none. Restrictions only administrator-level users can issue th...
Page 104
D-link des-3326s layer 3 switch cli reference show stp purpose used to display the switch’s current stp configuration. Syntax show stp description this command displays the switch’s current stp configuration. Parameters none restrictions none. Example usage: to display the status of stp on the switc...
Page 105
D-link des-3326s layer 3 switch cli reference status 2 : stp disabled des-3326s:4#show stp command: show stp bridge parameters settings stp status : disabled max age : 20 hello time : 2 forward delay : 15 priority : 32768 stp version : stp compatible tx hold count : 3 forwarding bpdu : enabled des-3...
Page 106
D-link des-3326s layer 3 switch cli reference example usage: to display stp state of port 1-9 of module 1: des-3326s:4#show stp ports command: show ports port designated bridge state cost pri edge p2p status role ------ ------------------ ----- ---------- ---- ---- --- ---------- ---------- 1 n/a ye...
Page 107
D-link des-3326s layer 3 switch cli reference 12 f orwarding d atabase c ommands the layer 2 forwarding database commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create fdb port create multicast_fdb config mult...
Page 108
D-link des-3326s layer 3 switch cli reference create fdb purpose used to create a static entry to the unicast mac address forwarding table (database) syntax create fdb [port ] description this command will make an entry into the switch’s unicast mac address forwarding database. Parameters − the name...
Page 109
D-link des-3326s layer 3 switch cli reference create multicast_fdb purpose used to create a static entry to the multicast mac address forwarding table (database) syntax create multicast_fdb description this command will make an entry into the switch’s multicast mac address forwarding database. Param...
Page 111
D-link des-3326s layer 3 switch cli reference config fdb aging_time purpose used to set the aging time of the forwarding database. Syntax config fdb aging_time description the aging time affects the learning process of the switch. Dynamic forwarding table entries, which are made up of the source mac...
Page 112
D-link des-3326s layer 3 switch cli reference delete fdb purpose used to delete an entry to the switch’s forwarding database. Syntax delete fdb description this command is used to delete a previous entry to the switch’s mac address forwarding database. Parameters − the name of the vlan on which the ...
Page 118
D-link des-3326s layer 3 switch cli reference show traffic control purpose used to display current traffic control settings. Syntax show traffic control description this command displays the current storm traffic control configuration on the switch. Parameters group_list − used to specify a broadcas...
Page 119: Qos
D-link des-3326s layer 3 switch cli reference 14 qos c ommands the des-3326s switch supports 802.1p priority queuing. The switch has 4 priority queues. These priority queues are numbered from 0 (class 0) — the lowest priority queue — to 3 (class 3) — the highest priority queue. The eight priority qu...
Page 120
D-link des-3326s layer 3 switch cli reference command parameters config bandwidth_control rx_rate no_limit tx_rate no_limit show bandwidth_control config scheduling max_packet max_latency show scheduling config 802.1p user_priority show 802.1p user_priority config 802.1p default_priority all show 80...
Page 122
D-link des-3326s layer 3 switch cli reference show bandwidth_control purpose used to display the bandwidth control configuration on the switch. Syntax show bandwidth_control {} description the show bandwidth_control command displays the current bandwidth control configuration on the switch, on a por...
Page 124
D-link des-3326s layer 3 switch cli reference config scheduling specified. The default value is 0. Max_latency − specifies the maximum amount of time the above specified priority queue will have to wait before being allowed to transmit any packets that have accumulated in its transmit buffer. A valu...
Page 125
D-link des-3326s layer 3 switch cli reference show scheduling purpose used to display the currently configured traffic scheduling on the switch. Syntax show scheduling description the show scheduling command displays the current configuration for the maximum number of packets (max_packets) and the m...
Page 126
D-link des-3326s layer 3 switch cli reference config 802.1p user_priority purpose used to map the 802.1p user priority of an incoming packet to one of the four hadware queues available on the switch. Syntax config 802.1p user_priority description the config 802.1p user_priority command is used to co...
Page 127
D-link des-3326s layer 3 switch cli reference show 802.1p user_priority purpose used to display the current mapping between an incoming packet’s 802.1p priority value and one of the switch’s four hardware priority queues. Syntax show 802.1p user_priority description the show 802.1p user_priority com...
Page 129
D-link des-3326s layer 3 switch cli reference show 802.1 default_priority purpose used to display the currently configured 802.1p priority value that will be assigned to an incoming, untagged packet before being forwarded to its destination. Syntax show 802.1p default_priority {} description the sho...
Page 130
D-link des-3326s layer 3 switch cli reference example usage: to display the current 802.1p default priority configuration on the switch: des-3326s:4# show 802.1p default_priority command: show 802.1p default_priority port priority ------- ----------- 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 10 0 11 0 12 ...
Page 134
D-link des-3326s layer 3 switch cli reference enable mirror purpose used to enable a previously entered port mirroring configuration. Syntax enable mirror description this command, combined with the disable mirror command below, allows you to enter a port mirroring configuration into the switch, and...
Page 135
D-link des-3326s layer 3 switch cli reference disable mirror purpose used to disable a previously entered port mirroring configuration. Syntax disable mirror description this command, combined with the enable mirror command above, allows you to enter a port mirroring configuration into the switch, a...
Page 136
D-link des-3326s layer 3 switch cli reference show mirror purpose used to show the current port mirroring configuration on the switch. Syntax show mirror description this command displays the current port mirroring configuration on the switch. Parameters none restrictions none. Example usage: to dis...
Page 139
D-link des-3326s layer 3 switch cli reference delete vlan purpose used to delete a previously configured vlan on the switch. Syntax delete vlan description this command will delete a previously configured vlan on the switch. Parameters − the vlan name of the vlan you want to delete. Restrictions onl...
Page 142
D-link des-3326s layer 3 switch cli reference enable gvrp purpose used to enable gvrp on the switch. Syntax enable gvrp description this command, along with disable gvrp below, is used to enable and disable gvrp on the switch, without changing the gvrp configuration on the switch. Parameters none. R...
Page 143
D-link des-3326s layer 3 switch cli reference disable gvrp purpose used to disable gvrp on the switch. Syntax disable gvrp description this command, along with disable gvrp below, is used to enable and disable gvrp on the switch, without changing the gvrp configuration on the switch. Parameters none...
Page 145
D-link des-3326s layer 3 switch cli reference show gvrp purpose used to display the gvrp status for a port list on the switch. Syntax show gvrp {} description this command displays the gvrp status for a port list on the switch parameters − specifies a range of ports for which the gvrp status is to b...
Page 148
D-link des-3326s layer 3 switch cli reference delete link_aggregation group_id purpose used to delete a previously configured link aggregation group. Syntax delete link_aggregation group_id description this command is used to delete a previously configured link aggregation group. Parameters − specif...
Page 153
D-link des-3326s layer 3 switch cli reference show lacp_ports purpose used to display current lacp port mode settings. Syntax show lacp_ports {} description this command will display the lacp mode settings as they are currently configured. Parameters - restrictions only administrator-level users can...
Page 156
D-link des-3326s layer 3 switch cli reference show ipif purpose used to display the configuration of an ip interface on the switch. Syntax show ipif description this command will display the configuration of an ip interface on the switch. Parameters none. Restrictions none. Example usage: to display...
Page 157: Igmp S
D-link des-3326s layer 3 switch cli reference 19 igmp s nooping c ommands the switch port commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config igmp_snooping all host_timeout router_timeout leave_timer robust...
Page 159
D-link des-3326s layer 3 switch cli reference config igmp_snooping querier purpose used to configure the time in seconds between general query transmissions, the maximum time in seconds to wait for reports from members and the permitted packet loss that guarantees igmp snooping. Syntax config igmp_s...
Page 161
D-link des-3326s layer 3 switch cli reference enable igmp_snooping purpose used to enable igmp snooping on the switch. Syntax enable igmp_snooping {forward_mcrouter_only} description this command allows you to enable igmp snooping on the switch. If forward_mcrouter_only is specified, the switch will...
Page 162
D-link des-3326s layer 3 switch cli reference disable igmp_snooping purpose used to enable igmp snooping on the switch. Syntax disable igmp_snooping description this command disables igmp snooping on the switch. Igmp snooping can be disabled only if ip multicast routing is not being used. Disabling ...
Page 163
D-link des-3326s layer 3 switch cli reference example usage: to show igmp snooping: des-3326s:4#show igmp_snooping command: show igmp_snooping multicast router only : disabled vlan name : default leave timer : 2 querier state : disabled querier router behavior : non-querier igmp snooping global stat...
Page 164
D-link des-3326s layer 3 switch cli reference example usage: command: show igmp_snooping group multicast group: 224.0.0.2 port member : 1:26,2:7 mac address : 01-00-5e-00-00-09 mac address : 01-00-5e-36-3f-4b port member : 1:26,2:7 vlan name : default multicast group: 239.255.255.250 des-3326s:4# to...
Page 166: 802.1X C
D-link des-3326s layer 3 switch cli reference 20 802.1x c ommands the des-3326s implements the server-side of the ieee 802.1x port-based and mac-based network access control. This mechanism is intended to allow only authorized users, or other network devices, access to network resources by establish...
Page 167
D-link des-3326s layer 3 switch cli reference command parameters config radius ipaddress auth_port key acct_port show radius 161.
Page 168
D-link des-3326s layer 3 switch cli reference enable 802.1x purpose used to enable the 802.1x server on the switch. Enable 802.1x description the enable 802.1x command enables the 802.1x port-based network access control server application on the switch. Parameters none. Restrictions only administra...
Page 171
D-link des-3326s layer 3 switch cli reference to display the 802.1x configuration settings: des-3326s:4#show 802.1x auth_configuration ports 1 command: show 802.1x auth_configuration ports 1 802.1x : enabled authentication mode : port_based authentication protocol : radius_eap port number : 15:1 cap...
Page 173
D-link des-3326s layer 3 switch cli reference config 802.1x auth_parameter purpose used to configure the 802.1x authentication parameters on a range of ports. The default parameter will return all ports in the specified range to their default 802.1x settings. Syntax config 802.1x auth_parameter port...
Page 174
D-link des-3326s layer 3 switch cli reference example usage: to configure 802.1x authentication parameters for ports 1 – 20: des-3326s:4#config 802.1x auth_parameter ports 1:1 – 1:20 direction both command: config 802.1x auth_parameter ports 1:1-1:20 direction both success. Des-3326s:4# config 802.1...
Page 179
D-link des-3326s layer 3 switch cli reference config radius delete purpose used to delete a previously entered radius server configuration. Syntax config radius delete description the config radius delete command is used to delete a previously entered radius server configuration. Parameters − assign...
Page 181
D-link des-3326s layer 3 switch cli reference show radius used to display the current radius configurations on the switch. Syntax show radius description the show radius command is used to display the current radius configurations on the switch. Parameters none. Restrictions none. Purpose example us...
Page 184
D-link des-3326s layer 3 switch cli reference and it is used to assign a priority in case a conflict occurs. The profile_id establishes a priority within the list of profiles. A lower profile_id gives the rule a higher priority. In case of a conflict in the rules entered for different profiles, the ...
Page 185
D-link des-3326s layer 3 switch cli reference create access_profile purpose used to create an access profile on the switch and to define which parts of each incoming frame’s header the switch will examine. Masks can be entered that will be combined with the values the switch finds in the specified f...
Page 186
D-link des-3326s layer 3 switch cli reference create access_profile 180
Page 187
D-link des-3326s layer 3 switch cli reference create access_profile parameters flag_mask – specifies examination of tcp flag field according to the type of flag. Specify all to examine all type of tcp flag fields. Urg – specifies urgent tcp flag field. Rst - specifies reset tcp flag field. Udp − spe...
Page 188
D-link des-3326s layer 3 switch cli reference delete access_profile purpose used to delete a previously created access profile. Syntax delete access_profile [profile_id ] profile_id − an integer between 1 and 255 that is used to identify the access profile that will be deleted with this command. Thi...
Page 189
D-link des-3326s layer 3 switch cli reference config access_profile purpose used to configure an access profile on the switch and to define specific values that will be used to by the switch to determine if a given packet should be forwarded or filtered. Masks entered using the create access_profile...
Page 190
D-link des-3326s layer 3 switch cli reference config access_profile parameters profile_id − specifies the index of the access list profile. Add access_id − adds an additional rule to the above specified access profile. The value specifies the relative priority of the additional rule. The lower acces...
Page 191
D-link des-3326s layer 3 switch cli reference config access_profile parameters flag – specifies examination of tcp flag field according to the type of flag. Specify all to examine all type of tcp flag fields. Urg – specifies urgent tcp flag field. Ack – specifies acknowledge tcp flag field. Psh - sp...
Page 192
D-link des-3326s layer 3 switch cli reference des-3326s:4# config access_profile profile_id 1 add access_id 1 ip source_ip 10.42.73.1 command: config access_profile profile_id 1 add access_id 1 ip source_ip 10.42.73.1 success. Des-3326s:4# show access_profile purpose used to display the currently co...
Page 193
D-link des-3326s layer 3 switch cli reference des-3326s:4#show access_profile command: show access_profile access profile id : 10 access profile table type : ip frame filter =============================================================================== = mask option : source ip mask 255.255.255.0 -...
Page 194
D-link des-3326s layer 3 switch cli reference create cpu access_profile purpose used to create an access profile specifically for cpu interface filtering on the switch. A cpu access profile defines the parts of each incoming frame’s header the switch will examine. Masks can be entered that will be c...
Page 195
D-link des-3326s layer 3 switch cli reference create cpu access_profile parameters protocol_id − specifies that the switch will examine the protocol field in each packet and if this field contains the value entered here, apply the following rules ip − specifies that the switch will examine the ip ad...
Page 196
D-link des-3326s layer 3 switch cli reference example usage: to create a cpu access profile: des-3326s:4# create cpu access_profile ethernet vlan source_mac 00-00- 00-00-00-01 command: create cpu access_profile ethernet vlan source_mac 00-00-00- 00-00-01 des-3326s:4# success. 190
Page 197
D-link des-3326s layer 3 switch cli reference config cpu access_profile purpose used to configure a cpu access profile used for cpu interface filtering and to define specific values that will be used to by the switch to determine if a given packet should be forwarded or filtered. Masks entered using...
Page 198
D-link des-3326s layer 3 switch cli reference parameters source_ip − specifies that the access profile will apply to only packets with this source ip address. Icmp − specifies that the switch will examine the internet control message protocol (icmp) field within each packet. Ip − specifies that the ...
Page 199
D-link des-3326s layer 3 switch cli reference example usage: to configure a cpu access profile: des-3326s:4# config cpu access_profile profile_id 101 add access_id 1 ip vlan default source_ip 20.2.2.3 destination_ip 10.1.1.252 dscp 3 icmp type 11 code 32 deny command: config cpu access_profile profi...
Page 200
D-link des-3326s layer 3 switch cli reference disable cpu_interface_filtering purpose used to disable cpu interface filtering on the switch. Syntax disable cpu_interface_filtering this command is used to disable cpu interface filtering on the switch. When cpu interface filtering is disabled, the cpu...
Page 201
D-link des-3326s layer 3 switch cli reference show cpu access_profile used to display the currently configured access profiles on the switch. Syntax show access_profile { profile_id } description the show cpu access_profile command is used to display the currently configured access profiles. Paramet...
Page 202
D-link des-3326s layer 3 switch cli reference example usage: to display all of the currently configured access profiles on the switch: des-3326s:4#show cpu access_profile command: show cpu access_profile access id : 1 (250) mode : permit ------------ ----------------- ----------------- ------ ------...
Page 203
D-link des-3326s layer 3 switch cli reference delete cpu access_profile access_profile restrictions only administrator-level users can issue this command. Example usage: to delete the cpu access profile with a profile id of 1: des-3326s:4# delete cpu access_profile profile_id 1 command: delete cpu a...
Page 204
D-link des-3326s layer 3 switch cli reference 22 t raffic s egmentation c ommands traffic segmentation allows you to further sub-divide vlans into smaller groups of ports that will help to reduce traffic on the vlan. The vlan rules take precedence, and then the traffic segmentation rules are applied...
Page 207
D-link des-3326s layer 3 switch cli reference 23 s tacking c ommands the stacking configuration commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config stacking mode disable enable slave master auto show stacki...
Page 209
D-link des-3326s layer 3 switch cli reference show stacking purpose used to display the current stacking information. Show stacking {mode} this command will display the current stacking information. Parameters mode − when specified this will display the current stacking mode. None – no specification...
Page 210
D-link des-3326s layer 3 switch cli reference to display the current stacking (auto mode) information: des-3326s:4#show sta command: show stacking id mac address port range mode version rps status model name --- ----------------- ---------- ---------- -------- ----------- ---------- *1 00-05-5d-1f-5...
Page 211: Sntp
D-link des-3326s layer 3 switch cli reference 24 t ime and sntp c ommands the simple network time protocol (sntp) (an adaptation of the network time protocol (npt)) commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command paramet...
Page 213
D-link des-3326s layer 3 switch cli reference show sntp purpose used to display the sntp information. Syntax show sntp description this command will display sntp settings information including the source ip address, time and poll interval. Parameters none. Restrictions only administrator-level users...
Page 214
D-link des-3326s layer 3 switch cli reference enable sntp purpose enables sntp server support. Syntax enable sntp description this will enable sntp support. Sntp service must be separately configured (see config sntp).Enabling and configuring sntp support will override any manually configured system...
Page 215
D-link des-3326s layer 3 switch cli reference config time purpose used to manually configure system time and date settings. Syntax config time date hh:mm:ss> description this will configure the system time and date settings. These will be overridden if sntp is configured and enabled. Parameters date...
Page 218
D-link des-3326s layer 3 switch cli reference config dst using a three character abbreviation (sun, mon, tue, wed, thu, fri, sat) s-mth - configure the month in which dst begins. - the month to begin dst expressed as a number. E-mth - configure the month in which dst ends. - the month to end dst exp...
Page 219
D-link des-3326s layer 3 switch cli reference des-3326s:4#config dst repeating s_week 2 s_day tue s_mth 4 s_time 15:00 e_week 2 e_day wed e_mth 10 e_time 15:30 offset 30 command: config dst repeating s_week 2 s_day tue s_mth 4 s_time 15:00 e_week 2 e _day wed e_mth 10 e_time 15:30 offset 30 success....
Page 221
D-link des-3326s layer 3 switch cli reference create arpentry purpose used to make a static entry into the arp table. Syntax create arpentry description this command is used to enter an ip address and the corresponding mac address into the switch’s arp table. Parameters − the ip address of the end n...
Page 223
D-link des-3326s layer 3 switch cli reference config arp_aging used to configure the age-out timer for arp table entries on the switch. Syntax config arp_aging time description this command sets the maximum amount of time, in minutes, that an arp entry can remain in the switch’s arp table, without b...
Page 225
D-link des-3326s layer 3 switch cli reference clear arptable purpose used to remove all dynamic arp table entries. Syntax clear arptable description this command is used to remove dynamic arp table entries from the switch’s arp table. Static arp table entries are not affected. Parameters none. Restr...
Page 226
D-link des-3326s layer 3 switch cli reference 26 r outing t able c ommands the routing table commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create iproute default primary backup delete iproute default show ip...
Page 237: Igmp C
D-link des-3326s layer 3 switch cli reference 28 igmp c ommands the igmp commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config igmp ipif all version query_interval max_response_time robustness_variable last_m...
Page 239
D-link des-3326s layer 3 switch cli reference show igmp purpose used to display the igmp configuration for the switch of for a specified ip interface. Show igmp {ipif } description this command will display the igmp configuration for the switch if no ip interface name is specified. If an ip interfac...
Page 240
D-link des-3326s layer 3 switch cli reference show igmp group purpose used to display the switch’s igmp group table. Syntax show igmp group {group } {ipif } this command will display the igmp group configuration. Group − the multicast group id. − the name of the ip interface the igmp group is part o...
Page 241
D-link des-3326s layer 3 switch cli reference 29 b ootp r elay c ommands the bootp relay commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command hops time config bootp_relay add ipif config bootp_relay delete ipif enable bootp_r...
Page 242
D-link des-3326s layer 3 switch cli reference config bootp_relay purpose used to configure the bootp relay feature of the switch. Syntax config bootp_relay {hops } {time } description this command is used to configure the bootp relay feature. Parameters hops − specifies the maximum number of relay a...
Page 243
D-link des-3326s layer 3 switch cli reference config bootp_relay add purpose used to add an ip destination address to the switch’s bootp relay table. Syntax config bootp_relay add ipif description this command adds an ip address as a destination to forward (relay) bootp packets to. Parameters − the ...
Page 244
D-link des-3326s layer 3 switch cli reference config bootp_relay delete purpose used to delete an ip destination addresses from the switch’s bootp relay table. Syntax config bootp_relay delete ipif description this command is used to delete an ip destination addresses in the switch’s bootp relay tab...
Page 245
D-link des-3326s layer 3 switch cli reference enable bootp_relay purpose used to enable the bootp relay function on the switch. Syntax enable bootp_relay description this command, in combination with the disable bootp_relay command below, is used to enable and disable the bootp relay function on the...
Page 246
D-link des-3326s layer 3 switch cli reference disable bootp_relay purpose used to disable the bootp relay function on the switch. Syntax disable bootp_relay description this command, in combination with the enable bootp_relay command above, is used to enable and disable the bootp relay function on t...
Page 247
D-link des-3326s layer 3 switch cli reference show bootp_relay purpose used to display the current bootp relay configuration. Syntax show bootp_relay {ipif } description this command will display the current bootp relay configuration for the switch, or if an ip interface name is specified, the bootp...
Page 248: Dns R
D-link des-3326s layer 3 switch cli reference 30 dns r elay c ommands the dns relay commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config dnsr primary secondary nameserver config dnsr add delete static enable...
Page 251
D-link des-3326s layer 3 switch cli reference enable dnsr purpose used to enable dns relay. Enable dnsr this command is used, in combination with the disable dnsr command below, to enable and disable dns relay on the switch. Restrictions only administrator-level users can issue this command. Syntax ...
Page 252
D-link des-3326s layer 3 switch cli reference enable dnsr cache purpose used to enable the dns relay cache. Syntax enable dnsr cache description this command is used, in combination with the disable dnsr cache command below, to enable and disable the dns relay cache. Parameters none. Restrictions on...
Page 253
D-link des-3326s layer 3 switch cli reference enable dnsr static purpose used to enable the dns relay static table. Syntax enable dnsr static this command, in combination with the disable dnsr static command below, is used to enable or disable the dns relay static table function. Parameters none. Re...
Page 254
D-link des-3326s layer 3 switch cli reference show dnsr used to display the current dns relay status. Syntax show dnsr {static} description this command is used to display the current dns relay status. Parameters static − allows the display of only the static entries into the dns relay table. If thi...
Page 255
D-link des-3326s layer 3 switch cli reference to display dns relay table: des-3326s:4#show dnsr command: show dnsr dnsr status : disabled primary name server : 10.48.74.122 secondary name server : 20.48.74.123 dnsr cache status : enabled dnsr static table status : enabled dns relay static table doma...
Page 259
D-link des-3326s layer 3 switch cli reference enable rip purpose used to enable rip. Syntax enable rip restrictions only administrator-level users can issue this command. Description this command is used to enable rip on the switch. Parameters none. Example usage: to enable rip. Des-3326s:4#enable r...
Page 260
D-link des-3326s layer 3 switch cli reference show rip purpose used to display the rip configuration and statistics for the switch. Syntax show rip {ipif } description this command will display the rip configuration and statistics for a given ip interface or for all ip interfaces. Parameters − the n...
Page 263
D-link des-3326s layer 3 switch cli reference enable dvmrp used to enable dvmrp. Enable dvmrp this command, in combination with the disable dvmrp below, to enable and disable dvmrp on the switch. Restrictions only administrator-level users can issue this command. Purpose syntax description parameter...
Page 264
D-link des-3326s layer 3 switch cli reference show dvmrp routing_table purpose used to display the current dvmrp routing table. Syntax show dvmrp routing table {ipaddress } description − the name of the ip interface for which you want to display the corresponding dvmrp routing table. Ipaddress − the...
Page 267
D-link des-3326s layer 3 switch cli reference show dvmrp purpose used to display the current dvmrp routing table. Syntax show dvmrp {} description the command will display the current dvmrp routing table. Parameters − the name of the ip interface for which you want to display the dvmrp routing table...
Page 270
D-link des-3326s layer 3 switch cli reference enable pim purpose used to enable pim function on the switch. Syntax enable pim description this command will enable pim for the switch. Pim settings must first be configured for specific ip interfaces using config pim command. Parameters none. Restricti...
Page 271
D-link des-3326s layer 3 switch cli reference disable pim purpose used to disable pim function on the switch. Syntax disable pim description this command will disable pim for the switch. Any previously configured pim settings will remain unchanged and may be enabled at a later time with the enable p...
Page 273
D-link des-3326s layer 3 switch cli reference show pim purpose used to display current pim configuration. Syntax show pim {ipif } description this command will list current pim configuration settings for a specified ip interface or all ip interfaces. Parameters ipif – the name of an ip interface for...
Page 274: Ip M
D-link des-3326s layer 3 switch cli reference 34 ip m ulticasting c ommands the ip multicasting commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters show ipmc cache group ipaddress show ipmc ipif {ipif protocol [dv...
Page 275
D-link des-3326s layer 3 switch cli reference show ipmc cache purpose used to display the current ip multicast forwarding cache. Syntax show ipmc cache {group } {ipaddres } description this command will display the current ip multicast forwarding cache. − the multicast group id. Parameters − the ip ...
Page 277: Md5 C
D-link des-3326s layer 3 switch cli reference 35 md5 c onfiguration c ommands the md5 configuration commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config md5 key create md5 key delete md5 key show md5 key eac...
Page 278
D-link des-3326s layer 3 switch cli reference config md5 purpose used to enter configure the password for an md5 key. Syntax config md5 key description this command is used to configure an md5 key and password. Parameters key − the md5 key id. − an md5 password of up to 16 characters. Restrictions o...
Page 279
D-link des-3326s layer 3 switch cli reference create md5 purpose used to create a new entry in the md5 key table. Syntax create md5 key description this command is used to create an entry for the md5 key table. Parameters − the md5 key id. − an md5 password of up to 16 bytes. Restrictions only admin...
Page 280
D-link des-3326s layer 3 switch cli reference delete md5 purpose used to delete an entry in the md5 key table. Syntax delete md5 key description this command is used to delete a specific entry in the md5 key table. Parameters − the md5 key id. Restrictions only administrator-level users can issue th...
Page 281
D-link des-3326s layer 3 switch cli reference show md5 purpose used to display an md5 key table. Syntax show md5 {key } description this command will display the current md5 key table. Parameters − the md5 key id. Restrictions none. Usage example to display the current md5 key: des-3326s:4#show md5 ...
Page 282: Ospf C
D-link des-3326s layer 3 switch cli reference 36 ospf c onfiguration c ommands the ospf configuration commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters router_id enable ospf disable ospf show ospf create ospf ar...
Page 284
D-link des-3326s layer 3 switch cli reference config ospf purpose used to configure the ospf router id. Syntax config ospf {router_id } description this command is used to configure the ospf router id. Parameters − the ospf router id. Restrictions only administrator-level users can issue this comman...
Page 285
D-link des-3326s layer 3 switch cli reference disable ospf purpose used to disable ospf on the switch. Syntax disable ospf description this command, in combination with the enable ospf command above, is used to enable and disable ospf on the switch. Parameters none. Restrictions only administrator-l...
Page 286
D-link des-3326s layer 3 switch cli reference usage example: to show ospf state: des-3326s:4#show ospf command: show ospf 0.0.0.0 normal none none ospf router id : 10.1.1.2 state : enabled ospf interface settings interface ip address area id state link metric status ------------ ------------------ -...
Page 287
D-link des-3326s layer 3 switch cli reference virtual interface configuration transit virtual hello dead authentication link area id neighbor router interval interval status ----------- --------------- -------- -------- -------------- ------ 10.0.0.0 20.0.0.0 10 60 none down 10.1.1.1 20.1.1.1 10 60 ...
Page 288
D-link des-3326s layer 3 switch cli reference des-3326s:4#create ospf area 10.48.74.122 type normal command: create ospf area 10.48.74.122 type normal des-3326s:4# success. 282.
Page 289
D-link des-3326s layer 3 switch cli reference delete ospf area purpose used to delete an ospf area. Syntax delete ospf area description this command is used to delete an ospf area. Parameters − − a 32-bit number in the form of an ip address (xxx.Xxx.Xxx.Xxx) that uniquely identifies the ospf area in...
Page 291
D-link des-3326s layer 3 switch cli reference show ospf area purpose used to display an ospf area’s configuration. Syntax show ospf area {} description this command will display the current ospf area configuration. Parameters − − a 32-bit number in the form of an ip address (xxx.Xxx.Xxx.Xxx) that un...
Page 293
D-link des-3326s layer 3 switch cli reference delete ospf host_route purpose used to delete an ospf host route. Syntax delete ospf host_route description this command is used to delete an ospf host route. Parameters − the ip address of the ospf host. Restrictions only administrator-level users can i...
Page 295
D-link des-3326s layer 3 switch cli reference show ospf host_route purpose used to display the current ospf host route table. Syntax show ospf host_route {} description this command will display the current ospf host route table. Parameters − the ip address of the host. Restrictions none. Usage exam...
Page 297
D-link des-3326s layer 3 switch cli reference delete ospf aggregation purpose used to delete an ospf area aggregation configuration. Syntax delete ospf aggregation lsdb_type [summary] this command is used to delete an ospf area aggregation configuration. Parameters − a 32-bit number in the form of a...
Page 299
D-link des-3326s layer 3 switch cli reference show ospf aggregation purpose used to display the current ospf area aggregation settings. Show ospf aggregation {} this command will display the current ospf area aggregation settings. Parameters − the ospf area id. Restrictions none. Syntax description ...
Page 301
D-link des-3326s layer 3 switch cli reference show ospf neighbor purpose used to display the current ospf neighbor router table. Syntax show ospf neighbor {} description this command will display the current ospf neighbor router table. − the ip address of the neighbor router. Parameters restrictions...
Page 302
D-link des-3326s layer 3 switch cli reference show ospf virtual neighbor purpose used to display the current ospf virtual neighbor router table. Syntax show ospf virtual_neighbor { } description this command will display the current ospf virtual neighbor router table. Parameters − a 32-bit number in...
Page 305
D-link des-3326s layer 3 switch cli reference show ospf ipif purpose used to display the current ospf interface settings for the specified interface name. Syntax show ospf ipif {} description this command will display the current ospf interface settings for the specified interface name. Parameters −...
Page 306
D-link des-3326s layer 3 switch cli reference show ospf all purpose used to display the current ospf settings of all the ospf interfaces on the switch. Syntax show ospf all description this command will display the current ospf settings for all ospf interfaces on the switch. Parameters none. Restric...
Page 307
D-link des-3326s layer 3 switch cli reference config ospf virtual_link purpose description this command is used to configure the ospf virtual interface settings. Parameters − a 32-bit number in the form of an ip address (xxx.Xxx.Xxx.Xxx) that uniquely identifies the ospf area in the ospf domain. − t...
Page 309
D-link des-3326s layer 3 switch cli reference delete ospf virtual_link purpose used to delete an ospf virtual interface. Syntax delete ospf virtual_link description this command will delete an ospf virtual interface from the switch. Parameters − a 32-bit number in the form of an ip address (xxx.Xxx....
Page 310
D-link des-3326s layer 3 switch cli reference show ospf virtual_link purpose used to display the current ospf virtual interface configuration. Syntax show ospf virtual_link { description this command will display the current ospf virtual interface configuration. Parameters − a 32-bit number in the f...
Page 311
D-link des-3326s layer 3 switch cli reference 37 c ommand h istory l ist the history list commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters ? Show command_history dir config command_history each command is liste...
Page 312
D-link des-3326s layer 3 switch cli reference ? Purpose used to display all commands in the command line interface (cli). Syntax ? Description this command will display all of the commands available through the command line interface (cli). Parameters none. Restrictions none. Example usage to displa...
Page 313
D-link des-3326s layer 3 switch cli reference show command_history purpose used to display the command history. Syntax show command_history description this command will display the command history. Parameters none. Restrictions none. Example usage to display the command history: des-3326s:4#show co...
Page 314
D-link des-3326s layer 3 switch cli reference dir purpose used to display all commands. Syntax dir description this command will display all commands. Parameters none. Restrictions none. Example usage config 802.1p default_priority config 802.1x auth_parameter ports config 802.1x init ctrl+c esc q q...
Page 315
D-link des-3326s layer 3 switch cli reference config command_history purpose used to configure the command history. Syntax config command_history description this command is used to configure the command history. Parameters − the number of previously executed commands maintained in the buffer. Up to...
Page 316
D-link des-3326s layer 3 switch cli reference a t echnical s pecifications general standard ieee 802.3 10base-t ethernet ieee 802.3u 100base-tx fast ethernet ieee 802.3ab 1000base-t gigabit ethernet ieee 802.1 p/q vlan ieee 802.3x full-duplex flow control ieee 802.3z 1000base-x ethernet protocols cs...
Page 317
D-link des-3326s layer 3 switch cli reference performance transmission method: store-and-forward packet buffer memory: 16 mb per device filtering address table: 8 k mac address per device packet filtering/ forwarding rate: full-wire speed for all connections. 148,800 pps per port (for 100mbps) 1,488...
Page 318
D-link des-3326s layer 3 switch cli reference b g lossary 100base-fx: 100mbps ethernet implementation over fiber. Ageing: the automatic removal of dynamic entries from the switch database which have timed-out and are no longer valid. Backbone port: a port that does not learn device addresses, and wh...
Page 319
D-link des-3326s layer 3 switch cli reference flow control: (ieee 802.3z) a means of holding packets back at the transmit port of the connected end station. Prevents packet loss at a congested switch port. Forwarding: the process of sending a packet toward its destination by an internetworking devic...
Page 320
D-link des-3326s layer 3 switch cli reference 314 telnet: a tcp/ip application protocol that provides virtual terminal service, letting a user log in to another computer system and access a host as if the user were connected directly to the host. Tftp: trivial file transfer protocol. Allows you to t...