Des-7200 hardware installation guide.
Des-7200 series hardware installation guide revision no.:v1.4 date: 2009/5/10 copyright statement all rights reserved. D-link corporation reserves all copyrights of this document. Any reproduction, excerption, backup, modification, transmission, translation or commercial use of this document or any ...
Preface thank you for using our switches. This manual provides you with detailed operation guide that allows you to easily install and use the switches. Scope this manual introduces functional and physical features of our switches and provides installation procedures, troubleshooting, technical spec...
D-link corporation provides excellent technical support services for all our products. You can obtain the technical assistance you need through any of the following channels: technical assistance d-link corporation website, on d-link corporation website, you can obtain the latest technical informa...
1 contents 1 product overview ................................................................................................................................ 1-1 1.1 product overview .......................................................................................................................
2 2.4 requirements of installation tools ............................................................................................. 2-9 2.5 unpacking inspection requirements ......................................................................................... 2-9 2.5.1 checking goods ...........
3 5 troubleshooting .................................................................................................................................. 5-1 5.1 general flow for troubleshooting installation faults................................................................. 5-1 5.2 common troubles...
Des-7200 hardware installation guide 1-1 1 product overview 1.1 product overview in recent years as the internet users grow at an explosive rate, they are no longer satisfied with various existing ways of communications that rely largely on telephone networks, and demand telecom operators to provide...
Des-7200 hardware installation guide 1-2 1.2 technical specifications of des-7206/7210 1.2.1 product features powerful expandability des-7200 supports strategic routing and ipv6. It provides faster and more effective processing ability by expanding high-performance multi-service cards. hot-swapp...
Des-7200 hardware installation guide 1-3 the pvlan (port protection) is used to isolate the information exchanged between users, without needing to occupy the vlan resources. The port mac address lock and port mac address access quantity restriction can bar the access from illegal hosts. a full ra...
Des-7200 hardware installation guide 1-4 1.2.2 technical specifications table 1-1 technical specifications product model des-7210: des-7206: module slot 10 (two for the management engine modules) 6 (two for the management engine modules) vlan 4k l2 protocol ieee802.3, ieee802.3u, ieee802.3z, ieee802...
Des-7200 hardware installation guide 1-5 product model des-7210: des-7206: fan 7210-fan (supporting hot swap ability and fault alarming) 7206-fan (supporting hot swap ability and fault alarming) environment emc gb9254-1998 fcc class a safety regulation gb4943-2001 mtbf 438,352hrs 505,339hrs operatin...
Des-7200 hardware installation guide 1-6 1.3 product appearance 1.3.1 appearance of the des-7210 figure 1-1 appearance of the des-7210 1. Air outlet layer: the air outlet layer of the entire system, discharging air on three sides; 2. Fan tray: the slot for the fan tray, which is the main heat dissip...
Des-7200 hardware installation guide 1-7 1.3.2 appearance of the des-7206 figure 1-2 appearance of the des-7206 1. Module layer: offering up to 6 module slots; 2. Power layer: supporting two ac or dc power supplies for the maximum. 3. Air outlet: located at the back of the chassis to discharge air. ...
Des-7200 hardware installation guide 1-8 the system module layer is a module plug-in frame, which mechanically supports various modules of the des-7210 system. At the bottom of the chassis are two power frames, above which are the air inlet layer. The air filter is located between the air inlet laye...
Des-7200 hardware installation guide 1-9 the slots for the two management modules are in the middle, and they are identified as m1 and m2 from left to right. The other eight module line cards are numbered as 1-8 from the left to the right. When in full configuration, the modules in the module slots ...
Des-7200 hardware installation guide 1-10 figure 1-4 ventilation/heat dissipation solution of the des-7206 note this structure is designed with air inlet from the front panels of the modules, and air outlet at the back. Six 120*120*38 fans are used to blow the air to the outside for convection and u...
Des-7200 hardware installation guide 1-11 7200-2xg module: it provides two 10-gigabit xfp interfaces. It features the functions of layer-2/3 wire speed switching and routing, and supports multi-mode xfp module with the wavelength being 850nm, single-mode xfp module with that being 1310nm, and single...
Des-7200 hardware installation guide 1-12 1.6.1 7200-cm1~4 control modules: figure 1-5, 1-7 shows the basic appearance of the 7200-cm1/cm3 which is the major management module of the des-7206; figure 1-6, 1-8 shows the basic appearance of the 7200-cm2/cm4 which is the major management module of des-...
Des-7200 hardware installation guide 1-13 program loading. It can also be used to connect the equipment such as remote nm workstation for remote management of the equipment. When it is connected to the ethernet port of the background computer, the standard network cable suffices. For remote manageme...
Des-7200 hardware installation guide 1-14 product model 7200-cm1 7200-cm2 7200-cm3 7200-cm4 led status, primary, alarm and 10/100m mgmt port led hot swap ability supported management redundancy supported power consumption emc gb9254-1998 fcc class a safety regulation gb4943-2001 mtbf 246,987hrs 240,...
Des-7200 hardware installation guide 1-15 table 1-4 leds on the front panel sign description detailed information status system led off: the module has not been powered on red: module fault flashing green: the module is initializing solid green: the module has finished initialization and can perform...
Des-7200 hardware installation guide 1-16 figure 1-10 basic appearance of the 7200-24 1. Interface 7200-24: it provides twelve 10/100/1000base-t electrical ports and twelve optical/electrical combo 1000m interfaces, and supports up to twenty-four 1000base-t interfaces or 12+m 1000base-t interfaces a...
Des-7200 hardware installation guide 1-17 product model 7200-24 transmission media 10/100/1000base-t: 100m (category-5 upt) 1000base-sx(850nm) 62.5/125um mmf: 220m 1000base-sx(850nm) 50/125um mmf: 500m 1000base-lx(1310nm) 9/125um smf: 10km 1000base-lh(1310nm) 9/125um smf: 40km led status, link/act h...
Des-7200 hardware installation guide 1-18 2. Leds the 7200-48 provides various system leds, as described in the following table: table 1-8 leds on the front panel sign description detailed information status system led off: the module has not been powered on. Red: module fault flashing green: the mo...
Des-7200 hardware installation guide 1-19 1.6.5 7200-2xg module figure 1-12 shows the basic appearance of the 7200-2xg, which is the line card module of the des-7200 series. 7200-2xg provides two 10-gigabit xfp interfaces and features the function of layer-2/3 wire speed switching. The 7200-2xg is h...
Des-7200 hardware installation guide 1-20 product model 7200-2xg mtbf 180,698hrs operating temperature 0 to 40°c storage temperature -40 to 70°c operating humidity 10% - 90% rh weight net weight: 2.8 kg dimensions 436*346*45 ( l x w x hmm) 1.6.6 7200-4xg module figure 1-13 shows the basic appearance...
Des-7200 hardware installation guide 1-21 table 1-13 technical specifications of the 7200-4xg product model 7200-4xg standard compliance ieee 802.3-2002 ieee 803.Ab, ieee 802.1d, and ieee 802.1q 802.1x authentication port type four 10-gigabit xfp interfaces transmission media 10gbase-sr(850nm) 62.5/...
Des-7200 hardware installation guide 1-22 note the 7200-24p provides twelve sfp optical ports and 10/100/1000base-t ports that are in the combo form. In other words, each sfp port corresponds to one 10/100/1000base-t port, and only one port can be used at a time, with the other being unavailable. Th...
Des-7200 hardware installation guide 1-23 product model 7200-24p transmission media 10/100/1000base-t: 100m (category-5 upt) 1000base-sx(850nm) 62.5/125um mmf: 220m 1000base-sx(850nm) 50/125um mmf: 500m 1000base-lx(1310nm) 9/125um smf: 10km 1000base-lh(1310nm) 9/125um smf: 40km led status, link/act ...
Des-7200 hardware installation guide 1-24 warning 7200-48p does not support the hot pull-out operation. You need to perform the following operations to achieve it: 1. Disconnect all cables connected to the cable card ports; 2. Hold the mode button for over three seconds until all leds on the cable c...
Des-7200 hardware installation guide 1-25 product model 7200-48p transmission media 10/100/1000base-t: 100m (category-5 upt) 1000base-sx(850nm) 62.5/125um mmf: 220m 1000base-sx(850nm) 50/125um mmf: 500m 1000base-lx(1310nm) 9/125um smf: 10km 1000base-lh(1310nm) 9/125um smf: 40km led status, link/act ...
Des-7200 hardware installation guide 1-26 sign description detailed information link/act port status led off: port is not linked. Green: the 1000base-x port is linked. Flashing green: data is transmitted on the 1000base-x port. Orange: the100base-x port is linked. Flashing orange: data is transmitte...
Des-7200 hardware installation guide 1-27 1. Interface 7200-24g2xge comes with two 10g xfp ports, 12 gigabit sfp ports and 12 gigabit optical-electrical multiplex ports, and offers gigabit-level line rate of layer 2/3 switching. With auto-negotiation enabled, the gigabit electrical port supports aut...
Des-7200 hardware installation guide 1-28 product model 7200-24g2xge hot swappability supported power consumption emc gb9254-1998 fcc class a safety regulation gb4943-2001 mtbf 151,800hrs operating temperature 0 to 40°c storage temperature -40 to 70°c operating humidity 10% to 90% rh weight net weig...
Des-7200 hardware installation guide 1-29 sign description detailed information link/act port status indicator electric port: off: the port is not linked. Green: the port is linked at 1000m. Orange: the port is linked at 10/100m. Flashing green: data is transmitted through the port. Optic port: off:...
Des-7200 hardware installation guide 1-30 figure 1-19 basic appearance of the 7200-ase3 1. Indicators 7200-ase3 module provides the leds for indicating system status, as described in the following table: table 1-24 leds on the front panel sign description detailed information status system led off: ...
Des-7200 hardware installation guide 1-31 table 1-26 leds on the front panel of the 7210-fan sign description detailed information power power led off: the fan tray has not been powered on solid green: the fan module is normally powered on alarm alarm led off: normally working red: the fan tray fail...
Des-7200 hardware installation guide 2-1 2 preparation before installation 2.1 safety suggestions to avoid personal injury and equipment damage, please carefully read the safety suggestions before you install the des-7210/7206. Note the following safety suggestions do not cover all possible dangers....
Des-7200 hardware installation guide 2-2 figure 2-1 schematic diagram for correctly moving the des-7210 figure 2-2 schematic diagram for correctly moving the des-7206 warning do not move the equipment by grasping the panel, power supply handle, ventilation holes of the chassis, as they are not desig...
Des-7200 hardware installation guide 2-3 do not maintain the equipment alone when it is energized, unless absolutely necessary. be sure to make a careful check before you shut down the power supply. do not place the equipment in a damp/wet location. Do not let any liquid enter the chassis co...
Des-7200 hardware installation guide 2-4 2.1.5 laser safety among the modules supported by the des-7210/7206, there are a great number of optical modules that are class i laser products. Therefore, pay attention to the following during your use of this product: when a fiber transceiver works, ensu...
Des-7200 hardware installation guide 2-5 figure 2-3 schematic diagram for the ventilation of the des-7210 figure 2-4 schematic diagram for the ventilation of the des-7206.
Des-7200 hardware installation guide 2-6 2.2.3 temperature and humidity requirements to ensure the normal working and a prolonged useful life of the des-7210/7206, appropriate temperature and humidity must be maintained in the equipment room. If the equipment room has temperature and humidity that d...
Des-7200 hardware installation guide 2-7 apart from dust, the salt, acid and sulfide in the air in the equipment room must also meet strict requirements, as such poisonous substances may accelerate the corrosion of the metal and the aging of some parts. The equipment room should be protected from th...
Des-7200 hardware installation guide 2-8 2.3.3 emc ground the ground required for emc design includes shielding ground, filter ground, noise and interference suppression, and level reference. All the above constitute the comprehensive grounding requirements. The grounding resistance should be less t...
Des-7200 hardware installation guide 2-9 3. Keep the equipment away from high-power radio transmitter, radar transmitting station, and high-frequency large-current device. 4. Measures must be taken to isolate static electricity. 2.3.5 precaution for fiber connection before you connect the fibers, ve...
Des-7200 hardware installation guide 3-1 3 product installation note 1. Before you install the des-7210/7206, make sure you have carefully read chapter 2 and this chapter. 2. Make sure that the requirements set forth in chapter 2 have been met..
Des-7200 hardware installation guide 3-2 3.1 installation flow dc ac assembly of the des-7210/7206 before installation install the cabinet mount the des-7210/7206 into the cabinet connect the system ground connect the power supply (ac or dc) insert various modules connect external port cables or fib...
Des-7200 hardware installation guide 3-3 3.2 installation verification the des-7210/7206 is a kind of complicated equipment, so you must carefully plan and arrange its installation location, networking mode, power supply, and wiring before installation. Verify the following before installation: th...
Des-7200 hardware installation guide 3-4 4. Install the tray and wiring layer on the rack according to the configuration of one rack with one cabinet and one rack with multiple cabinets. 3.4 mounting the des-7210/7206 into the cabinet 3.4.1 precautions before the des-7210/7206 is mounted into the ca...
Des-7200 hardware installation guide 3-5 figure 3-1 installing the fan tray of the des-7210 figure 3-2 installing the fan tray of the des-7206 3.6 installing the power supply the des-7210/7206 system provides ac and dc power, which can be installed in the same way by performing the following steps: ...
Des-7200 hardware installation guide 3-6 figure 3-3 schematic diagram for installing the power supply of the des-7210 figure 3-4 schematic diagram for installing the power supply of the des-7206.
Des-7200 hardware installation guide 3-7 2. Insert the power supply module into the cabinet along the guide rail, as shown in figure 3-6 and figure 3-7: figure 3-5 schematic diagram for installing the power supply of the des-7210 figure 3-6 schematic diagram for installing the power supply of the de...
Des-7200 hardware installation guide 3-8 3. Tighten the screws on both sides of the power supply by using a straight screwdriver, as shown in figure 3-8 and figure 3-9. Figure 3-7 schematic diagram for installing the power supply of the des-7210 figure 3-8 schematic diagram for installing the power ...
Des-7200 hardware installation guide 3-9 3.7 installing the handle for easy handling of the system, the des-7210/7206 chassis is provided with a handle, which can be installed by performing the following steps: 1. Align the handle with the sunk hole on the fastening bar; 2. Tighten the cross m4 sunk...
Des-7200 hardware installation guide 3-10 3.8 installing the cabling rack of the des-7210 the cabling rack of the des-7210 can be performed by performing the following steps: 1. Remove the blank panel of the tracing rack by loosing the captive screws with a straight screwdriver and the cross screws ...
Des-7200 hardware installation guide 3-11 figure 3-12 installing the cabling rack of the des-7210 3. Fasten the cabling rack by using the cross m3 screws provided, as shown in figure 3-14. (the cabling rack is available in two sizes, and you can select the appropriate one) figure 3-13 installing the...
Des-7200 hardware installation guide 3-12 3.9 installing the air filter of the des-7210 simply push the air filter of the des-7210 into the cabinet along the guide rail, as shown in figure 3-15. Figure 3-14 installing the air filter of the des-7210 note you are recommended to install the air filter ...
Des-7200 hardware installation guide 3-13 figure 3-15 connection of grounding posts on the des-7210/7206 back 3.10.2 precautions the sectional area of the grounding cable should be determined according to the possible maximum current. Cables of good conductor should be used. do not use bare wire...
Des-7200 hardware installation guide 3-14 figure 3-16 schematic diagram for the connection of the dc power cable 3.11.2 precautions before connecting the power supply, you must verify that the external power supply provided matches the power module installed of this equipment. before connecting ...
Des-7200 hardware installation guide 3-15 figure 3-17 schematic diagram for the connection of the ac power cable 3.12.2 precautions before connecting the power supply, you must verify that the external power supply provided matches the power module installed of this equipment. before connecting ...
Des-7200 hardware installation guide 3-16 3.14 removing boards from the des-7210/7206 3.14.1 steps for removing boards 1. Unplug all cables/fibers such as optical fibers and rj45 twisted pairs from the panel. 2. Tighten two captive screws on the panel. 3. Draw out the board by holding the ejector wi...
Des-7200 hardware installation guide 3-17 figure 3-19 schematic diagram for the components of the des-7206 3.15 installing boards on the des-7210/7206 3.15.1 simple steps of board installation 1. Remove the appropriate component card or blank panel according to 3.14. 2. Replace it with the appropria...
Des-7200 hardware installation guide 3-18 3. Insert the twisted pair with the rj45 port into the appropriate interface according to the identification on the panel of the line card. Distinguish the crossover cable and straight-through cable. 4. Connect the cables and optical fibers of each board in ...
Des-7200 hardware installation guide 4-1 4 des-7210/7206 maintenance 4.1 monitoring function of the des-7210/7206 when the des-7210/7206 is running, you can monitor the status of each board by inspecting the status led of the appropriate board. When the status led of a board is off, red, or flashing...
Des-7200 hardware installation guide 4-2 note during the process, you should clean the air filter of the des-7210/7206. 4.2.3 power supply maintenance when the power supply fails, you only need to disconnect the power cable, loosen the two panel screws on the power module, unplug the power module, r...
Des-7200 hardware installation guide 5-1 5 troubleshooting 5.1 general flow for troubleshooting installation faults abnormal working after installation check the cabinet installation check the mounting of the des-7210/7206 in the cabinet check the power connection check the installation of the power...
Des-7200 hardware installation guide 5-2 5.2 common troubleshooting procedures fault 1: the system login password is lost. [fault description] the system login password of the switch is forgotten or lost, and so it is not possible to configure the data. [troubleshooting] please contact d-link custom...
Des-7200 hardware installation guide 5-3 fault 5: the led is abnormal after a line card works for some time. [fault description] the status led of the line card is off or red. The link/act led of the line card is solid on when no network cable or optical fiber is plugged. The fault remains after res...
Des-7200 hardware installation guide 5-4 the serial port console outputs illegible characters. [troubleshooting] such problem is related to the settings of the serial port. Check if the settings of such parameters as the baud rate match those in the des-7210/7206 configuration guide..
Des-7200 hardware installation guide appendix a-1 a connectors and connection media a.1 1000base-t/100base-tx/10ba se-t port the 1000base-t/100base-tx/10base-t is a port that supports adaptation of three rates, and automatic mdi/mdix crossover at these three rates. The 1000base-t complies with ieee ...
Appendix des-7200 hardware installation guide a-2 figure a-3 connections of the twisted pairs of the 100base-tx/10base-t a.2 optical fiber connection for the optical fiber ports, select single-mode or multiple-mode optical fibers for connection according to the fiber module connected. The connection...
Des-7200 hardware installation guide appendix b-1 b mini-gbic and 10g xenpak modules we provide the appropriate 1000m sfp module (mini-gbic module) and 10g xenpak module for the types of interfaces of the switch modules. You can select the sfp or xenpak module to suit your specific needs. Below the ...
B-2 b.4 models and technical specifications of the 10g xenpak module table b-2 models and technical specifications of the 10g xenpak module xenpak model wavelength (nm) media type core size (nm) modular bandwidth (mhz/km) transmission distance optical intensity (max) reception sensitivity (max) stan...
Des-7200 hardware installation guide appendix b-3 xenpak model wavelength (nm) media type core size (nm) modular bandwidth (mhz/km) transmission distance optical intensity (max) reception sensitivity (max) standard compliance 10gbase- lr 1310 single-mode optical fiber (lc connector) 10 n/a max. 10km...
