1. DL manuals
  2. D-Link
  3. Switch
  4. DGS-1210/ME series
  5. Reference Manual

D-Link DGS-1210/ME series Reference Manual

Manual is about: Metro Ethernet Switches

Summary of DGS-1210/ME series

  • Page 1

    Cli reference guide product model : dgs-1210/me series metro ethernet switches release 1.20 ©copyright 2015. All rights reserved..

  • Page 2

    Information in this document is subject to change without notice. © 2014 d-link computer corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of d-link computer corporation is strictly forbidden. Trademarks used in this text: d-link and the d-link lo...

  • Page 3: Table Of Contents

    Table of contents introduction ...................................................................................................................................................... 1 using the console cli .................................................................................................

  • Page 4

    Config time_range ................................................................................................................................................ 33 show time_range .........................................................................................................................

  • Page 5

    Show filter dhcp_server ....................................................................................................................................... 63 show dhcp_server screening .................................................................................................................

  • Page 6

    Delete snmp v6host ............................................................................................................................................. 94 show snmp v6host ..........................................................................................................................

  • Page 7

    Disable dhcp_relay ............................................................................................................................................ 119 config dhcp_relay port ....................................................................................................................

  • Page 8

    Clear log ............................................................................................................................................................. 147 show log ..........................................................................................................................

  • Page 9

    Delete auto_fdb ................................................................................................................................................. 181 show auto_fdb ...........................................................................................................................

  • Page 10

    Config scheduling_mechanism .......................................................................................................................... 207 show scheduling_mechanism ..........................................................................................................................

  • Page 11

    Show asymmetric_vlan ...................................................................................................................................... 233 enable pvid auto_assign .......................................................................................................................

  • Page 12

    Link aggregation commands .................................................................................................................. 260 create link_aggregation ......................................................................................................................................

  • Page 13

    Config igmp_snooping data_driven_learning .................................................................................................... 291 clear igmp_snooping data_driven_group .......................................................................................................... 292 conf...

  • Page 14

    Config mcast_filter_profile profile_name .......................................................................................................... 321 config mcast_filter_profile ipv6 ......................................................................................................................

  • Page 15

    Create arpspoofing ........................................................................................................................................... 352 show arpspoofing ...........................................................................................................................

  • Page 16

    Show ssh authmode .......................................................................................................................................... 378 config ssh server ............................................................................................................................

  • Page 17

    Config eee port ................................................................................................................................................. 409 show eee_mode port ......................................................................................................................

  • Page 18: Introduction

    Dgs-1210/me metro ethernet switch cli reference guide 1 1 introduction the dgs-1210-10/me, dgs-1210-20/me, dgs-1210-28/me, dgs-1210-28p/me and dgs-1210-52/me are l2 managed metro ethernet switches. They consist of 16/24/48 10/100/1000mbps ports plus 4 dedicated sfp ports. The switch can be managed t...

  • Page 19

    Dgs-1210 metro ethernet managed switch cli reference guide 2 figure 1 –2 boot screen the switch’s mac address can also be found in the web management program on the switch information (basic settings) window in the configuration folder. The ip address for the switch must be set before it can be mana...

  • Page 20: Using The Console Cli

    Dgs-1210/me metro ethernet switch cli reference guide 3 2 using the console cli the switch supports a console management interface that allows the user to connect to the switch’s management agent via a serial port and a terminal or a computer running a terminal emulation program. The console can als...

  • Page 21

    Dgs-1210 metro ethernet managed switch cli reference guide 4 figure 2 –2 the ? Command when entering a command without its required parameters, the cli displays the prompt: command: config account message and the options listed below. Figure 2 –3 example command parameter help in this case, the comm...

  • Page 22

    Dgs-1210/me metro ethernet switch cli reference guide 5 figure 2 –4 using the up arrow to re-enter a command in the above example, the command config account was entered without the required parameter , the cli returned the command: config account prompt. The up arrow cursor control key was pressed ...

  • Page 23

    Dgs-1210 metro ethernet managed switch cli reference guide 6 figure 2 –6 next possible completions: show command in the above example, all of the possible next parameters for the show command are displayed. At the next command prompt in the example, the up arrow was used to re-enter the show command...

  • Page 24: Command Syntax

    Dgs-1210/me metro ethernet switch cli reference guide 7 3 command syntax the following symbols are used to dgscribe how command entries are made and values and arguments are specified in this manual. The online help contained in the cli and available through the console interface uses the same synta...

  • Page 25: {Braces}

    Dgs-1210 metro ethernet managed switch cli reference guide 8 {braces} purpose encloses an optional value or set of optional arguments. Syntax reset description execute “reset” will return the switch to its factory default setting. Example command reset please be aware that all configurations will be...

  • Page 26

    Dgs-1210/me metro ethernet switch cli reference guide 9 a displays the remaining pages without pausing between pages. Enter displays the next line or table entry..

  • Page 27: Basic Switch Commands

    Dgs-1210 metro ethernet managed switch cli reference guide 10 4 basic switch commands the basic switch commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter enable password encryption disable password encryption crea...

  • Page 29: Create Account

    Dgs-1210 metro ethernet managed switch cli reference guide 12 success. Dgs-1210-28p/me:5# disable password encryption purpose used to disable password encryption on a user account. Syntax disable password encryption description the user account configuration information will be stored in the configu...

  • Page 30: Config Account

    Dgs-1210/me metro ethernet switch cli reference guide 13 can be included, and (optionally) can be encrypted. Restrictions only administrator level users can issue this command. Usernames can be between 1 and 15 characters. Passwords can be between 0 and 15 characters. Note: you are not required to e...

  • Page 31: Show Account

    Dgs-1210 metro ethernet managed switch cli reference guide 14 show account purpose to display information about all user accounts on the switch. Syntax show account description the show account command displays all account usernames and their access levels created on the switch. Up to 31 user accoun...

  • Page 32: Show Session

    Dgs-1210/me metro ethernet switch cli reference guide 15 accounts. Parameters none. Restrictions only administrator-level users can issue this command. Example usage: to deletes all the previously created accounts: dgs-1210-28p/me:5# reset account command: reset account are you sure to proceed with ...

  • Page 33: Show Environment

    Dgs-1210 metro ethernet managed switch cli reference guide 16 parameters none. Restrictions none. Example usage: to display the switch information: dgs-1210-28p/me:5# show switch command: show switch device type : dgs-1210-28p/me mac address : 9c-d6-43-60-4f-a4 ip address : 10.90.90.90 (manual) vlan...

  • Page 34: Enable Jumbo_Frame

    Dgs-1210/me metro ethernet switch cli reference guide 17 dgs-1210-28p/me:5# enable jumbo_frame purpose to enable jumbo frames on the device. Syntax enable jumbo_frame description the enable jumbo_frame command enables jumbo frames on the device. Parameters none. Restrictions only administrator or op...

  • Page 35: Show Serial_Port

    Dgs-1210 metro ethernet managed switch cli reference guide 18 restrictions none. Example usage: to show the jumbo_frames configuration status on the device: dgs-1210-28/me:5# show jumbo_frame command: show jumbo_frame jumbo frame is enabled. Des-1210-52/me:5# show serial_port purpose used to display...

  • Page 36: Config Bootrom Password

    Dgs-1210/me metro ethernet switch cli reference guide 19 5_minutes − the console will log out the current user if there is no user input for 5 minutes. 10_minutes − the console will log out the current user if there is no user input for 10 minutes. 15_minutes − the console will log out the current u...

  • Page 37: Disable Clipaging

    Dgs-1210 metro ethernet managed switch cli reference guide 20 dgs-1210-28p/me:5# enable clipaging command: enable clipaging success. Dgs-1210-28p/me:5# disable clipaging purpose used to disable the pausing of the console screen scrolling at the end of each page when a command displays more than one ...

  • Page 38: Disable Web

    Dgs-1210/me metro ethernet switch cli reference guide 21 disable web purpose to disable the http-based management software on the switch. Syntax disable web description the disable web command disables the web-based management software on the switch. Parameters none. Restrictions only administrator ...

  • Page 39: Disable Autoconfig

    Dgs-1210 metro ethernet managed switch cli reference guide 22 disable autoconfig purpose use this to deactivate auto configuration from dhcp. Syntax disable autoconfig description the disable autoconfig command is used to instruct the switch not to accept auto configuration instruction from the dhcp...

  • Page 40: Enable Auto Learning

    Dgs-1210/me metro ethernet switch cli reference guide 23 restrictions none. Example usage: to display the autoconfig status: dgs-1210-28p/me:5# show autoconfig command: show autoconfig autoconfig state: enabled timeout : 50 sec dgs-1210-28p/me:5# enable auto learning purpose to enable the mac addres...

  • Page 42: Reset

    Dgs-1210/me metro ethernet switch cli reference guide 25 model_name: dgs-1210-28p/me hit any key to stop autoboot: 0 uncompressing kernel image ... Ok loading runtime image ...... Starting kernel ... 100% mac address : 9c-d6-43-60-4f-a4 h/w version : rev.A1 f/w version : 6.11.B037 .....................

  • Page 43: Reload Config Config_Id

    Dgs-1210 metro ethernet managed switch cli reference guide 26 will not save or reboot. Restrictions only administrator-level users can issue this command. Example usage: to restore all of the switch’s parameters to their default values: dgs-1210-28p/me:5# reset system command: reset system are you s...

  • Page 44: Top

    Dgs-1210/me metro ethernet switch cli reference guide 27 description the logout command terminates the current user’s session on the switch’s console. Parameters none. Restrictions none. Example usage: to terminate the current user’s console session: dgs-1210-28p/me:5# logout top purpose to display ...

  • Page 46: Traceroute

    Dgs-1210/me metro ethernet switch cli reference guide 29 corresponding entry will not be repeated. Size - specify the size of the test packet. A value of 1 to 6000 can be specified. Source_ip - specify the source ipv6 address of the ping packets. If specified this parameter, this ipv6 address will b...

  • Page 47: Traceroute6

    Dgs-1210 metro ethernet managed switch cli reference guide 30 tracing route to 10.90.90.92 with 10 hops max and 1 byte packets [!N - network unreachable !H - host unreachable !P - protocol unreachable] 1 0.0.0.0 * * * 2 0.0.0.0 * * * 3 0.0.0.0 * * * 4 0.0.0.0 * * * 5 0.0.0.0 * * * 6 0.0.0.0 * * * 7 ...

  • Page 48: Show Cpu Port

    Dgs-1210/me metro ethernet switch cli reference guide 31 show cpu port purpose to display the cpu port information. Syntax show cpu port description the show cpu port command displays the cpu port information. Parameters none. Restrictions only administrator users can issue this command. Example usa...

  • Page 49: Enable Telnet

    Dgs-1210 metro ethernet managed switch cli reference guide 32 dgs-1210-28p/me:5# enable telnet purpose to enable the telnet. Syntax enable telnet description the enable telnet command enables telnet. Parameters none. Restrictions only administrator or operate-level users can issue this command. Exam...

  • Page 50: Config Time_Range

    Dgs-1210/me metro ethernet switch cli reference guide 33 dgs-1210-28p/me:5# telnet 10.90.90.91 command: telnet 10.90.90.91 config time_range purpose to configure the time range on the switch. Syntax config time_range [[hours start_time end_time weekdays date from_day year month 12> date to_day year ...

  • Page 51: Show Tech Support

    Dgs-1210 metro ethernet managed switch cli reference guide 34 configuration. Parameters –specifies the time range name to be displayed. Restrictions none. Example usage: to display time range settings on the switch: dgs-1210-28p/me:5# show time_range command: show time_range time range information -...

  • Page 52: Clear Tech Support

    Dgs-1210/me metro ethernet switch cli reference guide 35 no stacktrace information. - system info. - device type : dgs-1210-28p/me mac address : 9c-d6-43-60-4f-a4 ip address : 10.90.90.90 (manual) vlan name : default subnet mask : 255.0.0.0 default gateway : 0.0.0.0 system boot version : 1.00.019 sy...

  • Page 53: Dhcp Autoimage Commands

    Dgs-1210 metro ethernet managed switch cli reference guide 36 5 dhcp autoimage commands the dhcp autoimage commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter enable autoimage diable autoimage show autoimage each c...

  • Page 54: Show Autoimage

    Dgs-1210/me metro ethernet switch cli reference guide 37 command: disable autoimage success. Dgs-1210-28p/me:5# show autoimage purpose to display the dhcp automatic image function on the switch. Syntax show autoimage description the disable autoimage command is used to display the dhcp automatic ima...

  • Page 56: Config Smtp

    Dgs-1210/me metro ethernet switch cli reference guide 39 example usage: to disable stmp feature on the switch: dgs-1210-28p/me:5# disable smtp command: disable smtp success. Dgs-1210-28p/me:5# config smtp purpose to configure the fields to set up the smtp server for the switch, along with setting e-...

  • Page 57: Smtp Sent_Testmsg

    Dgs-1210 metro ethernet managed switch cli reference guide 40 syntax show smtp description the show smtp command displays the smtp server settings on the switch. Parameters none. Restrictions none. Example usage: to display smtp information on the switch: dgs-1210-28p/me:5# show smtp command: show s...

  • Page 58

    Dgs-1210/me metro ethernet switch cli reference guide 41 sending mail, please wait... Success. Dgs-1210-28p/me:5#.

  • Page 60: Config Greeting_Message

    Dgs-1210/me metro ethernet switch cli reference guide 43 config greeting_message purpose used to configure the login banner (greeting message). Syntax config greeting_message {default} description the config greeting_message command to modify the login banner (greeting message). Parameters default –...

  • Page 61: Show Greeting_Message

    Dgs-1210 metro ethernet managed switch cli reference guide 44 dgs-1210-28p/me:5# config greeting_message command: config greeting_message greeting messages editor ================================================================================ dgs-1210-28p/me gigabit ethernet switch command line int...

  • Page 63: Config Ddp Report Timer

    Dgs-1210 metro ethernet managed switch cli reference guide 46 dgs-1210-28p/me:5# config ddp report enable command: config ddp report enable dgs-1210-28p/me:5# config ddp report timer purpose to configure the d-link discover protocol packet report timer. Syntax config ddp report timer description the...

  • Page 68: Command

    Dgs-1210/me metro ethernet switch cli reference guide 51 10 loopback detection commands the loopback detection commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter enable loopdetect disable loopdetect config loopdet...

  • Page 69: Config Loopdetect Mode

    Dgs-1210 metro ethernet managed switch cli reference guide 52 example usage: to disable the loopback detection feature on the switch: dgs-1210-28p/me:5# disable loopdetect command: disable loopdetect success. Dgs-1210-28p/me:5# config loopdetect mode purpose to configure the loop back detection mode...

  • Page 71

    Dgs-1210 metro ethernet managed switch cli reference guide 54 loopdetect interval : 2 recover time : 60 dgs-1210-28p/me:5#.

  • Page 74

    Dgs-1210/me metro ethernet switch cli reference guide 57 dgs-1210-28p/me:5# show dos_prevention land_attack command: show dos_prevention land_attack dos type : land attack state : enabled action : drop frame counts : - dgs-1210-28p/me:5# enable dos_prevention trap_log purpose used to enable a dos pr...

  • Page 75

    Dgs-1210 metro ethernet managed switch cli reference guide 58.

  • Page 76: Command

    Dgs-1210/me metro ethernet switch cli reference guide 59 12 pppoe circuit id insertion commands pppoe circuit id insertion is used to produce the unique subscriber mapping capability that is possible on atm networks between atm-dsl local loop and the pppoe server. The pppoe server will use the inser...

  • Page 77

    Dgs-1210 metro ethernet managed switch cli reference guide 60 command: config pppoe circuit_id_insertion state enable success. Dgs-1210-28p/me:5# config pppoe circuit_id_insertion ports purpose used to enable and disable pppoe circuit identifier insertion on a per port basis and specify how to encod...

  • Page 78

    Dgs-1210/me metro ethernet switch cli reference guide 61 show pppoe circuit_id_insertion purpose used to display the pppoe circuit identifier insertion status for the switch. Syntax show pppoe circuit_id_insertion description the show pppoe circuit_id_insertion command is used to display the global ...

  • Page 79: Command

    Dgs-1210 metro ethernet managed switch cli reference guide 62 13 dhcp server screening commands the dhcp server screenint commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Due to this function allow you not only to restrict all dh...

  • Page 80: Config Filter Dhcp_Server

    Dgs-1210/me metro ethernet switch cli reference guide 63 restrictions only administrator or operate-level users can issue this command. Example usage: to add an entry from the dhcp server/client filter list in the switch’s database: dgs-1210-28p/me:5# config filter dhcp_server add permit server_ip 1...

  • Page 81: Show Dhcp_Server Screening

    Dgs-1210 metro ethernet managed switch cli reference guide 64 illegal server log suppress duration : 5 minutes dgs-1210-28p/me:5# show dhcp_server screening purpose used to display current dhcp server screening information on the switch. Syntax show dhcp_server screening description the show dhcp_se...

  • Page 82: Command

    Dgs-1210/me metro ethernet switch cli reference guide 65 14 ip-mac-port binding commands the ip network layer uses a four-byte address. The ethernet link layer uses a six-byte mac address. Binding these two address types together allows the transmission of data between the layers. The primary purpos...

  • Page 84

    Dgs-1210/me metro ethernet switch cli reference guide 67 mac_address 00-00-00-00-01-02 port 3 success. Dgs-1210-28p/me:5# config address_binding ip_mac ports purpose used to configure an ip-mac-port binding state to enable or disable for specified ports. Syntax config address_binding ip_mac ports [ ...

  • Page 85

    Dgs-1210 metro ethernet managed switch cli reference guide 68 success. Dgs-1210-28p/me:5# show address_binding ip_mac log purpose used to display an ip-mac-port binding ip mac log information. Syntax show address_binding ip_mac log description the show address_binding ip_mac log command is used to d...

  • Page 86: Delete Address_Binding

    Dgs-1210/me metro ethernet switch cli reference guide 69 config address_binding auto_scan ipv6address purpose used to configure an ip-mac-port binding auto scan for specified ipv6 addresses. Syntax config address_binding auto_scan ipv6address from_ip to_ip description the config address_binding auto...

  • Page 87: Show Address_Binding

    Dgs-1210 metro ethernet managed switch cli reference guide 70 – specifies a port to be deleted for address binding. Restrictions only administrator or operate-level users can issue this command. Example usage: to delete all address binding entries on the switch: dgs-1210-28p/me:5# delete address_bin...

  • Page 88

    Dgs-1210/me metro ethernet switch cli reference guide 71 ip address mac address port --------------- -------------------- ---- 10.0.0.21 00-00-00-00-01-02 3 dgs-1210-28p/me:5# show address_binding auto_scan list purpose used to display ip-mac-port binding entries. Syntax show address_binding auto_sc...

  • Page 91

    Dgs-1210 metro ethernet managed switch cli reference guide 74 parameters none. Restrictions only administrator or operate-level users can issue this command. Example usage: to disable address binding dhcpv6 pd snooping on the switch: dgs-1210-28p/me:5# disable address_binding dhcp_pd_snoop command: ...

  • Page 92

    Dgs-1210/me metro ethernet switch cli reference guide 75 dgs-1210-28p/me:5# config address_binding vlan 1 vlan_mode state disable command: config address_binding vlan 1 vlan_mode state disable success. Dgs-1210-28p/me:5# enable address_binding roaming purpose used to enable address binding roaming. ...

  • Page 93

    Dgs-1210 metro ethernet managed switch cli reference guide 76 dhcp snoop of ip-mac-port binding roaming information. Parameters none. Restrictions none. Example usage: to display dhcp snoop of address binding roaming information on the switch: dgs-1210-28/me:5# show address_binding roaming command: ...

  • Page 94: Command

    Dgs-1210/me metro ethernet switch cli reference guide 77 15 network management (snmp) commands the switch supports the simple network management protocol (snmp) versions 1, 2c, and 3. Users can specify which version of the snmp users want to use to monitor and control the switch. The three versions ...

  • Page 97: Command

    Dgs-1210 metro ethernet managed switch cli reference guide 80 command parameter disable snmp twistedpair_port_link traps enable snmp duplicate_ip_detected traps disable snmp duplicate_ip_detected traps each command is listed in detail, as follows: create snmp user purpose to create a new snmp user a...

  • Page 100: Show Snmp View

    Dgs-1210 metro ethernet managed switch cli reference guide 48 auto − enables auto-negotiation for the specified range of ports. [10

  • Page 101: Delete Snmp Community

    Dgs-1210 metro ethernet managed switch cli reference guide 84 accessible to the snmp community. Read/write or read-only level permission for the mib objects accessible to the snmp community. Parameters − a string of up to 32 alphanumeric characters that is used to identify members of an snmp communi...

  • Page 102: Delete Snmp All_Community

    Dgs-1210/me metro ethernet switch cli reference guide 85 delete snmp all_community purpose to remove all snmp community string from the switch. Syntax delete snmp all_community description the delete snmp all_community command removes all previously defined snmp community string from the switch. Par...

  • Page 103: Config Snmp Engineid

    Dgs-1210 metro ethernet managed switch cli reference guide 86 config snmp engineid purpose to configure a name for the snmp engine on the switch. Syntax config snmp engineid description the config snmp engineid command configures a name for the snmp engine on the switch. Parameters − a string, of be...

  • Page 104: Show Community_Encryption

    Dgs-1210/me metro ethernet switch cli reference guide 87 the encryption state on snmp community string. Parameters none. Restrictions only administrator, operate or power user-level users can issue this command. Example usage: to enable the encryption state on snmp community string: dgs-1210-28p/me:...

  • Page 106: Delete Snmp Group

    Dgs-1210/me metro ethernet switch cli reference guide 89 agent. − a string of up to 32 alphanumeric characters that identifies the group of mib objects that a remote snmp manager is allowed to access on the switch. Restrictions only administrator, operate or power user-level users can issue this com...

  • Page 107: Show Snmp Groups

    Dgs-1210 metro ethernet managed switch cli reference guide 90 example usage: to display the currently configured snmp global state on the switch: dgs-1210-28p/me:5# show snmp global state command: show snmp global state snmp global state : enable dgs-1210-28p/me:5# show snmp groups purpose to displa...

  • Page 108

    Dgs-1210/me metro ethernet switch cli reference guide 91 32>] description the create snmp host command creates a recipient of snmp traps generated by the switch’s snmp agent. Parameters − the ip address of the remote management station to serve as the snmp host for the switch. V1 – specifies that sn...

  • Page 109: Delete Snmp Host

    Dgs-1210 metro ethernet managed switch cli reference guide 92 delete snmp host purpose to remove a recipient of snmp tr aps generated by the switch’s snmp agent. Syntax delete snmp host description the delete snmp host command deletes a recipient of snmp traps generated by the switch’s snmp agent. P...

  • Page 111: Delete Snmp V6Host

    Dgs-1210 metro ethernet managed switch cli reference guide 94 dgs-1210-28p/me:5# delete snmp v6host purpose to remove a recipient of snmp traps generated by the switch’s snmp agent. Syntax delete snmp v6host description the delete snmp host command deletes a recipient of snmp traps generated by the ...

  • Page 112: Enable Trusted_Host

    Dgs-1210/me metro ethernet switch cli reference guide 95 success. Dgs-1210-28p/me:5# enable trusted_host purpose to enable the trusted host. Syntax enable trusted_host description the enable trusted_host command enables the trusted host feature. Parameters none. Restrictions only administrator or op...

  • Page 113: Show Trusted_Host

    Dgs-1210 metro ethernet managed switch cli reference guide 96 vlan. If no ip addresses are specified, then there is nothing to prevent any ip address from accessing the switch, provided the user knows the username and password. Parameters − the ipv4 address of the trusted host to be created. Network...

  • Page 114: Delete Trusted_Host

    Dgs-1210/me metro ethernet switch cli reference guide 97 ip address subnet mask ------------------------------ ------------------------------ 10.90.90.91 255.255.255.255 3000::1 128 total entries: 2 dgs-1210-28p/me:5# delete trusted_host purpose to delete a trusted host entry made using the create t...

  • Page 115: Disable Snmp Traps

    Dgs-1210 metro ethernet managed switch cli reference guide 98 description the enable snmp traps command enables snmp trap support on the switch. Parameters none. Restrictions only administrator or operator-level users can issue this command example usage: to enable snmp trap support on the switch: d...

  • Page 116: Show Snmp Traps

    Dgs-1210/me metro ethernet switch cli reference guide 99 disable snmp authenticate traps purpose to disable snmp authentication traps support. Syntax disable snmp authenticate traps description the disable snmp authenticate traps command disables snmp authentication trap support on the switch. Param...

  • Page 117

    Dgs-1210 metro ethernet managed switch cli reference guide 100 enable snmp linkchange_traps purpose to enable snmp link change traps support on the switch. Syntax enable snmp linkchange_traps description the enable snmp linkchange_traps command is used to enable snmp link change traps support on the...

  • Page 119: Config Snmp System_Contact

    Dgs-1210 metro ethernet managed switch cli reference guide 102 ctrl+c esc q quit space n next page enter next entry a all config snmp system_contact purpose to enter the name of a contact person who is responsible for the switch. Syntax config snmp system_contact description the config snmp system_c...

  • Page 120

    Dgs-1210/me metro ethernet switch cli reference guide 103 description the config snmp system_ name command configures the name of the switch. Parameters − a maximum of 128 characters is allowed. A null string is accepted if there is no location dgsired. Restrictions only administrator or operator-le...

  • Page 121: Enable Snmp

    Dgs-1210 metro ethernet managed switch cli reference guide 104 success. Dgs-1210-28p/me:5# enable snmp purpose to enable snmp support. Syntax enable snmp description the enable snmp command enables snmp support on the switch. Parameters none. Restrictions only administrator or operator-level users c...

  • Page 122

    Dgs-1210/me metro ethernet switch cli reference guide 105 to enable snmp dhcp screening traps support on the switch: dgs-1210-28p/me:5# enable snmp dhcp_screening traps command: enable snmp dhcp_screening traps success. Dgs-1210-28p/me:5# disable snmp dhcp_ screening traps purpose to disable snmp dh...

  • Page 123

    Dgs-1210 metro ethernet managed switch cli reference guide 106 syntax disable snmp impb_violation traps description the disable snmp impb_violation traps command enables snmp impb violation traps support on the switch. Parameters none. Restrictions only administrator or operator-level users can issu...

  • Page 124: Enable Snmp Lbd Traps

    Dgs-1210/me metro ethernet switch cli reference guide 107 command disable enable snmp firmware_upgrade_state traps success. Dgs-1210-28p/me:5# enable snmp lbd traps purpose to enable snmp lbd traps. Syntax enable snmp lbd traps description the enable snmp lbd traps command enables snmp lbd traps sup...

  • Page 125

    Dgs-1210 metro ethernet managed switch cli reference guide 108 enables snmp port security violation traps on the switch. Parameters none. Restrictions only administrator or operator-level users can issue this command. Example usage: to enable snmp port security violation traps support on the switch:...

  • Page 126

    Dgs-1210/me metro ethernet switch cli reference guide 109 success. Dgs-1210-28p/me:5# disable snmp rstpport_state_change traps purpose to disable snmp rstp port state change traps. Syntax disable snmp rstpport_state_change traps description the disable snmp rstpport_state_change traps command disabl...

  • Page 127

    Dgs-1210 metro ethernet managed switch cli reference guide 110 restrictions only administrator or operator-level users can issue this command. Example usage: to disable the snmp duplicate_ip_detected traps on the switch: dgs-1210-28p/me:5# disable snmp duplicate_ip_detected traps command: disable sn...

  • Page 129: Upload

    Dgs-1210 metro ethernet managed switch cli reference guide 112 firmware_fromtftp − downloads and installs firmware on the switch from a tftp server. Image_id − indicates the image file is to be downloaded. Restrictions only administrator or operator-level users can issue this command. Example usage:...

  • Page 131: Show Firmware Information

    Dgs-1210 metro ethernet managed switch cli reference guide 114 show firmware information purpose used to display the firmware section information. Syntax show firmware information description the show firmware information command is used to display the firmware section information. Parameters none. ...

  • Page 132: Config Firmware Image_Id

    Dgs-1210/me metro ethernet switch cli reference guide 115 #------------------------------------------------------------------------------------------------ # dgs-1210-28p/me gigabit ethernet switch configuration # # firmware: build 6.11.B037 # copyright(c) 2010 d-link corporation. All rights reserve...

  • Page 133: Show Boot_File

    Dgs-1210 metro ethernet managed switch cli reference guide 116 id. Restrictions only administrator -level users can issue this command. Example usage: dgs-1210-28p/me:5# config firmware image_id 1 boot_up command: config firmware image_id 1 boot_up success. Dgs-1210-28p/me:5# show boot_file purpose ...

  • Page 134

    Dgs-1210/me metro ethernet switch cli reference guide 117 boot 1310720 0 0 image1 12357664 1798112 87 image2 12337184 1818592 87 filesystem 331776 3600384 8 dgs-1210-28p/me:5# show flash information.

  • Page 135: Dhcp Relay Commands

    Dgs-1210 metro ethernet managed switch cli reference guide 118 17 dhcp relay commands the dhcp relay commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter enable dhcp_relay disable dhcp_relay config dhcp_relay port s...

  • Page 138: Config Dhcp_Relay  Hops

    Dgs-1210/me metro ethernet switch cli reference guide 121 config dhcp_relay delete ipif system purpose to delete a dhcp server from the dhcp relay server list. Syntax config dhcp_relay delete ipif system description the config dhcp_relay delete ipif system command deletes a dhcp servers defined as a...

  • Page 140

    Dgs-1210/me metro ethernet switch cli reference guide 123 already exists in the packet received from the dhcp client. Drop − the packet will be dropped if the option 82 field already exists in the packet received from the dhcp client. Keep − the option 82 field will be retained if the option 82 fiel...

  • Page 142: Show Dhcp_Relay

    Dgs-1210/me metro ethernet switch cli reference guide 125 2 3 des-1210-28/me:5# show dhcp_relay purpose to display the dhcp relay settings on the switch . Syntax show dhcp_relay {ipif [system]} description the show dhcp_relay command displays the dhcp relay status and list of servers defined as dhcp...

  • Page 143: Disable Dhcp_Local_Relay

    Dgs-1210 metro ethernet managed switch cli reference guide 126 parameters none. Restrictions only administrator, operator or power user-level users can issue this command. Example usage: to enable the dhcp local relay: dgs-1210-28p/me:5# enable dhcp_local_relay command: enable dhcp_local_relay succe...

  • Page 144: Show Dhcp_Local_Relay

    Dgs-1210/me metro ethernet switch cli reference guide 127 to enable the port 8-10 of dhcp local relay: dgs-1210-28p/me:5# config dhcp_local_relay port 8-10 state enable command: config dhcp_local_relay port 8-10 state enable success. Dgs-1210-28p/me:5# config dhcp_local_relay vlan purpose to specify...

  • Page 145: Enable Dhcpv6_Relay

    Dgs-1210 metro ethernet managed switch cli reference guide 128 command: show dhcp_local_relay dhcp/bootp local relay status : enabled dhcp/bootp local relay portlist : none dhcp/bootp local relay vid list : dgs-1210-28p/me:5# enable dhcpv6_relay purpose to enable dhcpv6 relay function on the switch ...

  • Page 147

    Dgs-1210 metro ethernet managed switch cli reference guide 130 command: config dhcpv6_relay add ipif system 3000::1 success. Dgs-1210-28p/me:5# config dhcpv6_relay hop_count purpose used to configure the dhcpv6 relay hop count of the switch. Syntax config dhcpv6_relay hop_count description the confi...

  • Page 148

    Dgs-1210/me metro ethernet switch cli reference guide 131 restrictions only administrator or operate-level users can issue this command. Example usage: to configure the dhcpv6 relay option 18 to be enabled on the switch: dgs-1210-28p/me:5# config dhcpv6_relay option_18 state enable command: config d...

  • Page 149

    Dgs-1210 metro ethernet managed switch cli reference guide 132 subscriber id to use default value or user defined. Restrictions only administrator or operate-level users can issue this command. Example usage: to configure the dhcpv6 relay option 38 on the switch: dgs-1210-28p/me:5# config dhcpv6_rel...

  • Page 151

    Dgs-1210 metro ethernet managed switch cli reference guide 134 success. Dgs-1210-28p/me:5# config gratuitous_arp send dup_ip_detected purpose used to enable or disable the sending of gratuitous arp requests while duplicate ip addresses are detected. Syntax config gratuitous_arp send send dup_ip_dete...

  • Page 152: Enable Gratuitous_Arp

    Dgs-1210/me metro ethernet switch cli reference guide 135 gratuitous arp packets. Restrictions only administrator or operator-level users can issue this command. Example usage: to enable learning of arp entries based on the received gratuitous arp packets: dgs-1210-28p/me:5# config gratuitous_arp le...

  • Page 153: Show Gratuitous_Arp

    Dgs-1210 metro ethernet managed switch cli reference guide 136 dgs-1210-28p/me:5# disable gratuitous_arp trap command: disable gratuitous_arp trap success. Dgs-1210-28p/me:5# show gratuitous_arp purpose used to display the gratuitous arp configuration. Syntax show gratuitous_arp description the show...

  • Page 154

    Dgs-1210/me metro ethernet switch cli reference guide 137 example usage: to configure gratuitous arp intervals for the switch: dgs-1210-28p/me:5# config gratuitous_arp send periodically interval 100 command: config gratuitous_arp send periodically interval 100 success. Dgs-1210-28p/me:5#.

  • Page 157: 20  1

    Dgs-1210 metro ethernet managed switch cli reference guide 140 20 1 cpu protection commands the cpu protection commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter enable cpu_protect disable cpu_protect config cpu_p...

  • Page 159

    Dgs-1210 metro ethernet managed switch cli reference guide 142 dgs-1210-28p/me:5# show cpu_protect command: show cpu_protect cpu protect state : enabled cpu protect type rate limit(pps) ------------------------- ------------------------ arp no limit bpdu no limit icmp no limit igmp no limit snmp no ...

  • Page 160: Network Monitoring Commands

    Dgs-1210/me metro ethernet switch cli reference guide 143 21 network monitoring commands the network monitoring commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter show packet ports show error ports show utilizatio...

  • Page 161: Show Error Ports

    Dgs-1210 metro ethernet managed switch cli reference guide 144 sent and received by ports specified in the port list. The results are separated into three tables, labeled a, b, and c in the window below. Table a is relevant to the size of the packets, table b is relevant to the type of packets and t...

  • Page 162: Show Utilization

    Dgs-1210/me metro ethernet switch cli reference guide 145 rx frames tx frames ------------------ ------------------- crc error 0 excessive deferral 0 undersize 0 crc error 0 oversize 0 late collision 0 fragment 8 excessive collision 0 jabber 0 single collision 0 drop pkts 0 collision 0 dgs-1210-28p/...

  • Page 163: Clear Counters

    Dgs-1210 metro ethernet managed switch cli reference guide 146 five seconds - 7 % one minute - 6 % five minutes - 6 % cpu utilization : ------------------------------------------------------------------------------- five seconds - 7 % one minute - 6 % five minutes - 6 % ctrl+c esc q quit space n nex...

  • Page 164: Clear Log

    Dgs-1210/me metro ethernet switch cli reference guide 147 clear log purpose to clear the switch’s history log. Syntax clear log description the clear log command clears the switch’s history log. Parameters none. Restrictions only administrator or operator-level users can issue this command. Example ...

  • Page 165: Disable Syslog

    Dgs-1210 metro ethernet managed switch cli reference guide 148 syntax enable syslog description the enable syslog command enables the system log to be sent to a remote host. Parameters none. Restrictions only administrator or operator-level users can issue this command. Example usage: to enable the ...

  • Page 167

    Dgs-1210 metro ethernet managed switch cli reference guide 150 0 kernel messages 1 user-level messages 2 mail system 3 system daemons 4 security/authorization messages 5 messages generated internally by syslog 6 line printer subsystem 7 network news subsystem 8 uucp subsystem 9 clock daemon 10 secur...

  • Page 168: Config Syslog Host

    Dgs-1210/me metro ethernet switch cli reference guide 151 dgs-1210-28p/me:5# create syslog host 1 ipaddress 1.1.2.1 severity all state enable command: create syslog host 1 ipaddress 1.1.2.1 severity all state enable success. Dgs-1210-28p/me:5# config syslog host purpose to configure the syslog proto...

  • Page 169

    Dgs-1210 metro ethernet managed switch cli reference guide 152 supports. Numerical facility code 0 kernel messages 1 user-level messages 2 mail system 3 system daemons 4 security/authorization messages 5 messages generated internally by syslog 6 line printer subsystem 7 network news subsystem 8 uucp...

  • Page 171: Cable Diagnostic Port

    Dgs-1210 metro ethernet managed switch cli reference guide 154 dgs-1210-28p/me:5# show syslog host command: show syslog host host id host ip address severity facility udp port status --------- ----------------------- ----------- ------------ ------------- ----------- 1 1.1.2.1 all local0 514 enabled...

  • Page 172: Config Sysgroupinterval

    Dgs-1210/me metro ethernet switch cli reference guide 155 description the config syslogintimeout command is used to configure the system login timeout. Parameters − specify the system login time. The range is between 3 and 30 minutes. Restrictions only administrator or operator-level users can issue...

  • Page 173

    Dgs-1210 metro ethernet managed switch cli reference guide 156 command: show log_software_module cli system dgs-1210-28p/me:5#.

  • Page 177

    Dgs-1210 metro ethernet managed switch cli reference guide 160 success! Dgs-1210-28p/me:5#.

  • Page 179: Config Stp Ports

    Dgs-1210 metro ethernet managed switch cli reference guide 162 the stp version that is currently set on the switch. Parameters maxage − this value may be set to ensure that old information does not endlessly circulate through redundant paths in the network, preventing the effective propagation of th...

  • Page 181: Config Stp Version

    Dgs-1210 metro ethernet managed switch cli reference guide 164 dgs-1210-28p/me:5# config stp ports 1-3 externalcost 19 state enable command: config stp ports 1-3 externalcost 19 state enable success. Dgs-1210-28p/me:5# config stp version purpose to globally set the version of stp on the switch. Synt...

  • Page 182: Config Stp Priority

    Dgs-1210/me metro ethernet switch cli reference guide 165 config stp priority purpose to update the stp instance configuration. Syntax config stp priority instance_id description the config stp priority command updates the stp instance configuration settings on the switch. The mstp uses the priority...

  • Page 183: Show Stp

    Dgs-1210 metro ethernet managed switch cli reference guide 166 globally disabled on the switch. Parameters none. Restrictions only administrator-level users can issue this command. Example usage: to disable stp on the switch: dgs-1210-28p/me:5# disable stp command: disable stp success. Dgs-1210-28p/...

  • Page 184: Show Stp Ports

    Dgs-1210/me metro ethernet switch cli reference guide 167 status 2: stp enabled for rstp dgs-1210-28p/me:5# show stp command: show stp stp bridge global settings ------------------------------------------------------ stp status : enabled stp version : rstp bridge priority : 32768 max age : 8 hello t...

  • Page 185: Show Stp Instance

    Dgs-1210 metro ethernet managed switch cli reference guide 168 syntax show stp ports {} description the show stp ports command displays the stp instance settings and stp instance operational status currently implemented on the switch. Parameters – a port or range of ports to be configured. The port ...

  • Page 186: Show Stp Mst_Config_Id

    Dgs-1210/me metro ethernet switch cli reference guide 169 port 0 , path cost 0 regional root bridge 9c:d6:43:60:4f:a4 priority 32768 path cost 0 designated bridge 9c:d6:43:60:4f:a4 priority 32768 configured forward delay 15, max age 18, max hops 20 operational forward delay 15, max age 18 interface ...

  • Page 187: Delete Stp Instance_Id

    Dgs-1210 metro ethernet managed switch cli reference guide 170 to create instance id 1: dgs-1210-28p/me:5# create stp instance_id 1 command: create stp instance_id 1 warning: there is no vlan mapping to this instance_id! Success. Dgs-1210-28p/me:5# delete stp instance_id purpose to delete instance i...

  • Page 188: Config Stp Mst_Config_Id

    Dgs-1210/me metro ethernet switch cli reference guide 171 example usage: to configure instance id 2 to add vid 10: dgs-1210-28p/me:5# config stp instance_id 2 add_vlan 10 command : config stp instance_id 2 add_vlan 10 success. Dgs-1210-28p/me:5# config stp mst_config_id purpose to update the mstp co...

  • Page 189: Config Stp Trap

    Dgs-1210 metro ethernet managed switch cli reference guide 172 identical, the mstp function implements the lowest port number into the forwarding state and other interfaces are blocked. Remember that lower priority values mean higher priorities for forwarding packets. Parameters – a port or range of...

  • Page 190

    Dgs-1210/me metro ethernet switch cli reference guide 173 example usage: to configure the new root and topo change to be enabled for stp trap: dgs-1210-28p/me:5# config stp trap new_root disable topo_change enable command: config stp trap new_root disable topo_change enable success. Dgs-1210-28p/me:...

  • Page 191: Command

    Dgs-1210 metro ethernet managed switch cli reference guide 174 24 forwarding database commands the forwarding database commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter create fdb port create multicast_fdb config...

  • Page 192: Config Fdb Aging_Time

    Dgs-1210/me metro ethernet switch cli reference guide 175 restrictions only administrator or operator-level users can issue this command. Example usage: to create a unicast mac fdb entry: dgs-1210-28p/me:5# create fdb default 00-00-00-00-01-02 port 2 command: create fdb default 00-00-00-00-01-02 por...

  • Page 193: Enable Flood_Fdb

    Dgs-1210 metro ethernet managed switch cli reference guide 176 example usage: to delete a permanent fdb entry: dgs-1210-28p/me:5# delete fdb default 00-00-00-00-01-02 command: delete fdb default 00-00-00-00-01-02 success. Dgs-1210-28p/me:5# enable flood_fdb purpose to enable the switch’s forwarding ...

  • Page 198: Delete Auto_Fdb

    Dgs-1210/me metro ethernet switch cli reference guide 181 delete auto_fdb purpose to delete a static entry in the auto forwarding table (database). Syntax delete auto_fdb description the delete auto_fdb command removes a static entry in the multicast mac address forwarding table (database). Paramete...

  • Page 200: Show Traffic Control

    Dgs-1210/me metro ethernet switch cli reference guide 183 to configure traffic control and enable broadcast storm control system wide: dgs-1210-28p/me:5# config traffic control all multicast enable unicast disable broadcast enable threshold 64 command: config traffic control all multicast enable uni...

  • Page 201

    Dgs-1210 metro ethernet managed switch cli reference guide 184 is cleared. Storm_occured – a notification will be generated when a storm event is detected. Both – a notification will be generated both when a storm event is detected and cleared. None – no notification will be generated when storm eve...

  • Page 202: 26  2

    Dgs-1210/me metro ethernet switch cli reference guide 185 26 2 password recovery commands the password recovery commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter enable password_recovery disable password_recovery...

  • Page 203: Show Password_Recovery

    Dgs-1210 metro ethernet managed switch cli reference guide 186 dgs-1210-28/me:5# disable password_recovery command: disable password_recovery success. Des-1210-52/me:5# show password_recovery purpose to show the password recovery mode on the switch. Syntax show password_recovery description the show...

  • Page 205: Command

    Dgs-1210 metro ethernet managed switch cli reference guide 188 command parameter protocol_mapping config cos vlanid_mapping vid class show cos vlanid_mapping {vid } delete cos vlanid_mapping vid config cos tos value class show cos tos {value } config cos tcp_port_mapping destination_port class show ...

  • Page 206: Config Scheduling

    Dgs-1210/me metro ethernet switch cli reference guide 189 config scheduling purpose to configure traffic scheduling for each of the switch’s qos queues. Syntax config scheduling weight description the config scheduling commandconfigures traffic scheduling for each of the switch’s qos queues. The swi...

  • Page 207: Config Bandwidth_Control

    Dgs-1210 metro ethernet managed switch cli reference guide 190 description the show scheduling command displays the current configuration for the maximum number of packets (max_packet) value assigned to the four priority classes of service on the switch. The switch empties the four hardware queues i...

  • Page 208: Show Bandwidth_Control

    Dgs-1210/me metro ethernet switch cli reference guide 191 t o configure bandwidth control configuration: dgs-1210-28p/me:5# config bandwidth_control all rx_rate no_limit tx_rate no_limit command: config bandwidth_control all rx_rate no_limit tx_rate no_limit success dgs-1210-28p/me:5# show bandwidth...

  • Page 209: Show Cos Mac_Mapping

    Dgs-1210 metro ethernet managed switch cli reference guide 192 to configure the cos mac mapping on the switch: dgs-1210-28p/me:5# config cos mac_mapping destination_addr 00-01-c2- 11-22-33 class 2 command: config cos mac_mapping destination_addr 00-01-c2-11-22-33 class 2 success. Dgs-1210-28p/me:5# ...

  • Page 210: Config Cos Ip_Mapping

    Dgs-1210/me metro ethernet switch cli reference guide 193 success. Dgs-1210-28p/me:5# config cos ip_mapping purpose to configure the cos ip mapping method. Syntax config cos ip_mapping destination_ip class 0-7> description the config cos ip_mapping command is used to configure the cos ip mapping met...

  • Page 211: Delete Cos Ip_Mapping

    Dgs-1210 metro ethernet managed switch cli reference guide 194 delete cos ip_mapping purpose to remove the cos ip mapping method. Syntax delete cos ip_mapping destination_ip description the delete cos ip_mapping command is used to delete the cos ip mapping method on the switch. Parameters - specifie...

  • Page 212: Delete Cos Ipv6_Mapping

    Dgs-1210/me metro ethernet switch cli reference guide 195 parameters - specifies the ipv6 address to be displayed. For example, 3000::1. Restrictions none. Example usage: to display the cos ipv6 mapping on the switch: dgs-1210-28p/me:5# show cos ipv6_mapping destination_ipv6 3000::1 command: show co...

  • Page 213: Delete Cos Ipv6_Tc_Mapping

    Dgs-1210 metro ethernet managed switch cli reference guide 196 to configure the cos ipv6 tc mapping on the switch: dgs-1210-28p/me:5# config cos ipv6_tc_mapping trafficclass 1 class 2 command: config cos ipv6_tc_mapping trafficclass 1 class 2 success. Dgs-1210-28p/me:5# delete cos ipv6_tc_mapping pu...

  • Page 215: Show Cos Protocol_Mapping

    Dgs-1210 metro ethernet managed switch cli reference guide 198 5 802.1p dscp dgs-1210-28p/me:5# config cos protocol_mapping purpose to configure the cos protocol mapping method on the switch. Syntax config cos protocol_mapping protocol class description the config cos protocol_mapping command is use...

  • Page 216: Config Cos Vlanid_Mapping

    Dgs-1210/me metro ethernet switch cli reference guide 199 delete cos protocol_mapping purpose to delete the cos protocol mapping between an incoming packet ’s 802.1p priority value. Syntax delete cos protocol_mapping protocol description the delete cos protocol_mapping command is used to delete the ...

  • Page 217: Delete Cos Vlanid_Mapping

    Dgs-1210 metro ethernet managed switch cli reference guide 200 description the show cos vlanid_mapping command is used to display the cos vlan id mapping information between an incoming packet ’s 802.1p priority value. Parameters - specifies the mapped vlan id information to be displayed. Restrictio...

  • Page 218: Show Cos Tos

    Dgs-1210/me metro ethernet switch cli reference guide 201 restrictions only administrator or operator-level users can issue this command. Example usage: to configure a cos tos on the switch: dgs-1210-28p/me:5# config cos tos value 1 class 1 command: config cos tos value 1 class 1 success. Dgs-1210-2...

  • Page 219: Show Cos Tcp_Port_Mapping

    Dgs-1210 metro ethernet managed switch cli reference guide 202 parameters - specifies the tcp port number to be mapped. - specifies the number of the switch ’s hardware priority queue. Restrictions only administrator or operator-level users can issue this command. Example usage: to configure the cos...

  • Page 220

    Dgs-1210/me metro ethernet switch cli reference guide 203 restrictions only administrator or operator-level users can issue this command. Example usage: to delete the cos tcp port mapping on the switch: dgs-1210-28p/me:5# delete cos tcp_port_mapping destination_port 500 command: delete cos tcp_port_...

  • Page 221

    Dgs-1210 metro ethernet managed switch cli reference guide 204 dgs-1210-28p/me:5# show cos udp_port_mapping command: show cos udp_port_mapping udp port class ------------------------------------------- 500 2 dgs-1210-28p/me:5# delete cos udp_port_mapping purpose to delete the cos udp port mapping in...

  • Page 222: Show 802.1P User_Priority

    Dgs-1210/me metro ethernet switch cli reference guide 205 6 3 2 7 3 2 parameters − the 802.1p priority value (0 to 7) to map to one of the switch’s four hardware priority classes of service. − the switch’s hardware priority class of service (0 to 7) to map to the 802.1p priority value specified abov...

  • Page 226: Show Dscp_Mapping

    Dgs-1210/me metro ethernet switch cli reference guide 209 dgs-1210-28p/me:5# show dscp_mapping purpose to display the setting of dscp mapping. Syntax show dscp_mapping {dscp_value } description the show dscp_mapping command displays the mapping of dscp value. Parameters dscp_value - the selected val...

  • Page 228: Disable Rmon

    Dgs-1210/me metro ethernet switch cli reference guide 211 dgs-1210-28p/me:5# enable rmon command: enable rmon success. Dgs-1210-28p/me:5# disable rmon purpose to disable remote monitoring (rmon) status for the snmp function. Syntax disable rmon description the disable rmon command disables remote mo...

  • Page 229: Delete Rmon Alarm

    Dgs-1210 metro ethernet managed switch cli reference guide 212 threshold. Rising-threshold − specifies the rising counter value that triggers the rising threshold alarm. − specifies the event that triggers the specific alarm. Falling-threshold − specifies the falling counter value that triggers the ...

  • Page 231

    Dgs-1210 metro ethernet managed switch cli reference guide 214 delete rmon collection stats purpose to remove the network collection stats. Syntax delete rmon collection stats description the delete rmon collection stats command removes the network collection stats on the switch. Parameters − specif...

  • Page 232: Create Rmon Event

    Dgs-1210/me metro ethernet switch cli reference guide 215 delete rmon collection history purpose to remove the network collection history. Syntax delete rmon collection history description the delete rmon collection history command removes the network collection history on the switch. Parameters − s...

  • Page 233: Delete Rmon Event

    Dgs-1210 metro ethernet managed switch cli reference guide 216 delete rmon event purpose to remove the network event. Syntax delete rmon event description the delete rmon event command removes the network event on the switch. Parameters − specifies the event number to be removed. Restrictions only a...

  • Page 234

    Dgs-1210/me metro ethernet switch cli reference guide 217 parameters − specifies the statistics index of rmon to be displayed. Restrictions none. Example usage: to display the rmon statistics on the switch: dgs-1210-28p/me:5# show rmon statistics command: show rmon statistics rmon is enabled etherne...

  • Page 235: Port Mirroring Commands

    Dgs-1210 metro ethernet managed switch cli reference guide 218 29 port mirroring commands the port mirroring commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter enable mirror disable mirror config mirror target [ad...

  • Page 236: Config Mirror Target

    Dgs-1210/me metro ethernet switch cli reference guide 219 parameters none. Restrictions only administrator or operator-level users can issue this command. Example usage: to disable mirroring configurations: dgs-1210-28p/me:5# disable mirror command: disable mirror success. Dgs-1210-28p/me:5# config ...

  • Page 237: Show Mirror

    Dgs-1210 metro ethernet managed switch cli reference guide 220 show mirror purpose to show the current port mirroring configuration on the switch. Syntax show mirror description the show mirror command displays the current port mirroring configuration on the switch. Parameters none. Restrictions non...

  • Page 241: Config Gvrp

    Dgs-1210 metro ethernet managed switch cli reference guide 224 to add ports 4 through 8 as tagged ports to the vlan 3: dgs-1210-28p/me:5# config vlan vlanid 3 add tagged 4- 8 command: config vlan vlanid 3 add tagged 4-8 success . Dgs-1210-28p/me:5# config gvrp purpose to configure configures the gro...

  • Page 242: Enable Gvrp

    Dgs-1210/me metro ethernet switch cli reference guide 225 receiving of gvrp information, and the port vlan id (pvid). Parameters join_timer − specifies the join time for the gvrp on the switch. The time range is from 100 to 100000 seconds. Leave_timer − specifies the leave time for the gvrp on the s...

  • Page 244: Config Dot1V_Protocol_Group

    Dgs-1210/me metro ethernet switch cli reference guide 227 group for protocol vlan function. Parameters group_id − the id of a protocol group which is used to identify a set of protocols. Group_name − the name of the protocol group. The maximum length is 32 characters. Restrictions only administrator...

  • Page 245: Show Dot1V_Protocol_Group

    Dgs-1210 metro ethernet managed switch cli reference guide 228 description the delete dot1v_protocol_group command deletes a protocol group. Parameters group_id − specifies the group id to be deleted. Group_name − the name of the protocol group. The maximum length is 32 characters. Restrictions only...

  • Page 247: Show Gvrp

    Dgs-1210 metro ethernet managed switch cli reference guide 230 dgs-1210-28p/me:5# show gvrp purpose to display the gvrp status for a port list or port channel on the switch. Syntax show gvrp {} description the show gvrp command displays the gvrp status for a port list or a port channel on the switch...

  • Page 248: Enable Vlan_Trunk

    Dgs-1210/me metro ethernet switch cli reference guide 231 join-time leave-time leave-all-time ----------- ---------- -------------- 100 600 10000 dgs-1210-28p/me:5# enable vlan_trunk purpose to enable vlan trunking on the switch. Syntax enable vlan_trunk description the enable vlan_trunk command, al...

  • Page 249: Config Vlan_Trunk Ports

    Dgs-1210 metro ethernet managed switch cli reference guide 232 syntax show vlan_trunk description the show vlan_trunk command displays summary information about vlan trunking status and configured ports. Parameters none. Restrictions none. Example usage: to display the switch’s current vlan_trunk se...

  • Page 250: Disable Asymmetric_Vlan

    Dgs-1210/me metro ethernet switch cli reference guide 233 example usage: to enable asymettric vlan on the switch: dgs-1210-28p/me:5# enable asymmetric_vlan command: enable asymmetric_vlan success. Dgs-1210-28p/me:5# disable asymmetric_vlan purpose to disable asymmetric vlan on the switch. Syntax dis...

  • Page 251: Disalbe Pvid Auto_Assign

    Dgs-1210 metro ethernet managed switch cli reference guide 234 description the enable pvid auto_assign command enables the auto-assign of pvid. When this is enabled, pvid will be possibly changed by pvid or vlan configuration. When user configures a port to vlan x ’s untagged membership, this port’s...

  • Page 252

    Dgs-1210/me metro ethernet switch cli reference guide 235 to display the auto-assign pvid state: dgs-1210-28p/me:5# show pvid auto_assign command: show pvid auto_assign pvid auto-assignment: enabled dgs-1210-28p/me:5# create mac_based_vlan mac_address purpose to create a static mac-based vlan entry....

  • Page 253: Config Vlan_Auto_Learn

    Dgs-1210 metro ethernet managed switch cli reference guide 236 restrictions only administrator and operator and power-user-level users can issue this command. . Example usage: to delete a static mac-based vlan entry: dgs-1210-28p/me:5# delete mac_based_vlan mac_address 00-00-00-11-22- 33 vlan defaul...

  • Page 254: Show Vlan_Auto_Learn

    Dgs-1210/me metro ethernet switch cli reference guide 237 description this config vlan_auto_learn command is used to configure mac address autolearning on a vlan to be enabled or disabled. Parameters - specifies the vlan id to be configured. Restrictions only administrator and operator and power-use...

  • Page 255: Command

    Dgs-1210 metro ethernet managed switch cli reference guide 238 31 mac-based access control commands the mac-based access control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter enable mac_based_access_control d...

  • Page 256

    Dgs-1210/me metro ethernet switch cli reference guide 239 enable mac_based_access_control purpose to enable mac-based access control. Syntax enable mac_based_access_control description the enable mac_based_access_control command will enable the mac-based ac function. Parameters none. Restrictions on...

  • Page 257

    Dgs-1210 metro ethernet managed switch cli reference guide 240 is 16. Restrictions only administrator or operator-level users can issue this command. Example usage: to configure mac-based ac password: dgs-1210-28p/me:5# config mac_based_access_control password 1234 command: config mac_based_access_c...

  • Page 258

    Dgs-1210/me metro ethernet switch cli reference guide 241 unauthenticated state. Block_time – if a host fails to pass the authentication, the next authentication will not started within block_time unless the user clears the entry state manually. Restrictions only administrator or operator-level user...

  • Page 259

    Dgs-1210 metro ethernet managed switch cli reference guide 242 example usage: to disable log state of mac-based access control: dgs-1210-28p/me:5# config mac_based_access_control log state disable command: config mac_based_access_control log state disable success. Dgs-1210-28p/me:5# config mac_based...

  • Page 261

    Dgs-1210 metro ethernet managed switch cli reference guide 244 dgs-1210-28p/me:5# show mac_based_access_control_local command: show mac_based_access_control_local id : 1 mac address : 00-11-22-33-44-55 vlan id : 1 success. Dgs-1210-28p/me:5# show mac_based_access_control auth_state ports purpose to ...

  • Page 262

    Dgs-1210/me metro ethernet switch cli reference guide 245 to delete the local database entry by mac address with vlan id 2: dgs-1210-28p/me:5# delete mac_based_access_control_local mac 00–00–00– 00–00–01 vlanid 2 command: delete mac_based_access_control_local mac 00–00–00–00–00–01 vlanid 2 success. ...

  • Page 263: Command

    Dgs-1210 metro ethernet managed switch cli reference guide 246 32 web-based access control commands the web-based access control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter enable wac disable wac config wac...

  • Page 264: Disable Wac

    Dgs-1210/me metro ethernet switch cli reference guide 247 success. Dgs-1210-28p/me:5# disable wac purpose to disable the wac function. Syntax disable wac description the disable wac command is used to disable the wac function. Parameters none. Restrictions only administrator or operator-level users ...

  • Page 266: Config Wac Virtual_Ip

    Dgs-1210/me metro ethernet switch cli reference guide 249 dgs-1210-28p/me:5# to configure the wac port aging time: dgs-1210-28p/me:5# config wac ports 8-12 aging_time 200 command: config wac ports 8-12 aging_time 200 success. Dgs-1210-28p/me:5# config wac switch_http_port purpose to configure the tc...

  • Page 267: Create Wac User

    Dgs-1210 metro ethernet managed switch cli reference guide 250 to configure the wac virtual ip address used to accept authentication requests from unauthenticated hosts: dgs-1210-28p/me:5# config wac virtual_ip 1.1.1.1 command: config wac virtual_ip 1.1.1.1 success. Dgs-1210-28p/me:5# create wac use...

  • Page 268: Show Wac User

    Dgs-1210/me metro ethernet switch cli reference guide 251 dgs-1210-28p/me:5# delete wac user dlink command: delete wac user dlink success. Dgs-1210-28p/me:5# show wac user purpose to display wac user accounts. Syntax show wac user description the show wac user command is is used to display wac user ...

  • Page 272: Disable Qinq

    Dgs-1210/me metro ethernet switch cli reference guide 255 dgs-1210-28p/me:5# disable qinq purpose to disable the q-in-q mode. Syntax disable qinq description the disable qinq command creates a used to disable the q-in-q mode. All dynamically learned l2 address will be cleared. All dynamically regist...

  • Page 273: Show Qinq Rxtable

    Dgs-1210 metro ethernet managed switch cli reference guide 256 add inner tag: disabled --------------------------------------------------------- port id: 2 --------------------------------------------------------- role: uni miss drop: disabled outer tpid: 0x8100 add inner tag: disabled -------------...

  • Page 274: Config Qinq Inner_Tpid

    Dgs-1210/me metro ethernet switch cli reference guide 257 restrictions only administrator or operator-level users can issue this command. Example usage: to configure port list 1 to 4 as nni port, set outer tpid to 0x88a8: dgs-1210-28p/me:5# config qinq ports 1-3 role nni outer_tpid 0x88a8 command: c...

  • Page 275: Show Vlan_Translation

    Dgs-1210 metro ethernet managed switch cli reference guide 258 dgs-1210-28p/me:5# create vlan_translation add cvid 2 svid 2 command: create vlan_translation add cvid 2 svid 2 success. Dgs-1210-28p/me:5# show vlan_translation purpose to display the current vlan translation rules on the switch. Syntax...

  • Page 276

    Dgs-1210/me metro ethernet switch cli reference guide 259 dgs-1210-28p/me:5#.

  • Page 278: Delete Link_Aggregation

    Dgs-1210/me metro ethernet switch cli reference guide 261 restrictions only administrator or operator-level users can issue this command. Example usage: to create a link aggregation group: dgs-1210-28p/me:5# create link_aggregation group_id 1 command: create link_aggregation group_id 1 success. Dgs-...

  • Page 279

    Dgs-1210 metro ethernet managed switch cli reference guide 262 restrictions only administrator or operator-level users can issue this command. Link aggregation groups may not overlap. Example usage: to define a load-sharing group of ports, group-id 2 with group members ports 1-5: dgs-1210-28p/me:5# ...

  • Page 284

    Dgs-1210/me metro ethernet switch cli reference guide 267 on the switch. Parameters - specifies the ip interface name. Restrictions none. Example usage: to display ip interface settings: dgs-1210-28p/me:5# show ipif command: show ipif ip setting mode : static interface name : system interface vlan n...

  • Page 286

    Dgs-1210/me metro ethernet switch cli reference guide 269 how to handle bpdu. That is, when bpdu tunneling is enabled on a port and the bpdu attack protection function is enabled, then bpdu tunneling is effectively disabled on the port. Parameters – specifies a range of ports to be configured. All –...

  • Page 288: Disable Bpdu_Protection

    Dgs-1210/me metro ethernet switch cli reference guide 271 dgs-1210-28p/me:5# enable bpdu_protection command: enable bpdu_protection success. Dgs-1210-28p/me:5# disable bpdu_protection purpose used to globally disablebpdu attack protection on the switch. Syntax disable bpdu_protection description the...

  • Page 289

    Dgs-1210 metro ethernet managed switch cli reference guide 272 dgs-1210-28p/me:5# show bpdu_protection command: show bpdu_protection bpdu protection global settings --------------------------------------------------------------- bpdu protection status : disabled bpdu protection recover time : 60 sec...

  • Page 293: Show Ethernet_Oam Ports

    Dgs-1210 metro ethernet managed switch cli reference guide 276 sizes between the peers. (5) oam configuration revision: the configuration revision of the oam entity as reflected in the latest oampdu sent by the oam entity. The config revision is used by oam entities to indicate that configuration ch...

  • Page 294: Show Ethernet_Oam Ports

    Dgs-1210/me metro ethernet switch cli reference guide 277 displayed. Restrictions none. Example usage: to show ethernet oam configuration of port 1: dgs-1210-28p/me:5# show ethernet_oam ports 1 configuration command: show ethernet_oam ports 1 configuration port 1 ------------------------------------...

  • Page 295: Show Ethernet_Oam Ports

    Dgs-1210 metro ethernet managed switch cli reference guide 278 example usage: to show ethernet oam statistics of port 1: dgs-1210-28p/me:5# show ethernet_oam ports 1 statistics command: show ethernet_oam ports 1 statistics port 1 -------------------------------------------------------------------- i...

  • Page 296: Clear Ethernet_Oam Ports

    Dgs-1210/me metro ethernet switch cli reference guide 279 ----------------------------------------------------------------------- event listing index type location time stamp ----- ------------------------------------------ ------------- --------------------- local event statistics error symbol even...

  • Page 297: Mac Notification Commands

    Dgs-1210 metro ethernet managed switch cli reference guide 280 38 mac notification commands the igmp snooping commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter enable mac_notification disable mac_notification con...

  • Page 298: Config Mac_Notification

    Dgs-1210/me metro ethernet switch cli reference guide 281 address notification without changing configuration. Parameters none. Restrictions only administrator or operator-level users can issue this command. Example usage: to disable mac notification without changing basic configuration: dgs-1210-28...

  • Page 299: Show Mac_Notification

    Dgs-1210 metro ethernet managed switch cli reference guide 282 to enable port 7 for mac address table notification: dgs-1210-28p/me:5# config mac_notification ports 7 enable command: config mac_notification ports 7 enable success. Dgs-1210-28p/me:5# show mac_notification purpose used to display the ...

  • Page 300

    Dgs-1210/me metro ethernet switch cli reference guide 283 port mac address table notification state ---- ------------------------------------------------------ 1 disabled 2 disabled 3 disabled dgs-1210-28p/me:5#.

  • Page 304

    Dgs-1210/me metro ethernet switch cli reference guide 287 dgs-1210-28p/me:5# config igmp_snooping querier vlanid 2 state enable command: config igmp_snooping querier vlanid 2 state enable success . Dgs-1210-28p/me:5# create igmp_snooping multicast_vlan purpose to create an igmp snooping multicast vl...

  • Page 309: Config Router_Ports

    Dgs-1210 metro ethernet managed switch cli reference guide 292 to configure the igmp snooping data driven learning on the switch: dgs-1210-28p/me:5# config igmp_snooping data_driven_learning all state disable command: config igmp_snooping data_driven_learning all state disable success.Dgs-1210-28p/m...

  • Page 310

    Dgs-1210/me metro ethernet switch cli reference guide 293 the following parameter , to the router port function. − a port or range of ports that will be configured as router ports. Restrictions only administrator, operator or power user-level users can issue this command. Example usage: to add the s...

  • Page 311

    Dgs-1210 metro ethernet managed switch cli reference guide 294 description the config igmp access_authentication ports command configures the igmp access authentication on the switch. Parameters − a port or range of ports that will be configured as igmp access authentication ports. All − specify all...

  • Page 313: Show Igmp_Snooping Group

    Dgs-1210 metro ethernet managed switch cli reference guide 296 parameters − the name of the vlan for which igmp snooping configuration is to be displayed. Up to 32 characters can be used. − the vid of the vlan for which igmp snooping configuration is to be displayed. Restrictions none. Example usage...

  • Page 314: Show Igmp_Snooping Host

    Dgs-1210/me metro ethernet switch cli reference guide 297 {data_driven} − specifies to display the data driven of igmp snooping group. Restrictions none. Example usage: to show igmp snooping group: dgs-1210-28p/me:5# show igmp_snooping group vlan default command: show igmp_snooping group vlan defaul...

  • Page 315

    Dgs-1210 metro ethernet managed switch cli reference guide 298 igmp snooping forwarding table entries currently configured on the switch. Parameters ports − the ports of igmp snooping host table information are to be displayed. Group − the ip address of igmp snooping host table information are to be...

  • Page 316: Show Router_Ports

    Dgs-1210/me metro ethernet switch cli reference guide 299 show igmp_snooping multicast_vlan_group purpose to display the igmp snooping multicast vlan group table entries on the switch. Syntax show igmp_snooping multicast_vlan_group {} description the show igmp_snooping multicast_vlan_group command d...

  • Page 317

    Dgs-1210 metro ethernet managed switch cli reference guide 300 dynamic router port : forbidden router port : total entries : 1 dgs-1210-28p/me:5#.

  • Page 318: 40  3

    Dgs-1210/me metro ethernet switch cli reference guide 301 40 3 layer 2 protocol tunneling commands the layer 2 protocol tunneling (l2pt) commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter enable l2protocol_tunnel ...

  • Page 319: Show L2Protocol_Tunnel

    Dgs-1210 metro ethernet managed switch cli reference guide 302 example usage: to disable the layer 2 protocol tunneling function: dgs-1210-28p/me:5# disable l2protocol_tunnel command: disable l2protocol_tunnel success. Dgs-1210-28p/me:5# config l2protocol_tunnel ports purpose to configure layer 2 pr...

  • Page 320

    Dgs-1210/me metro ethernet switch cli reference guide 303 protocol tunneling information. Parameters uni - specify show uni detail information, include tunneled and dropped pdu statistic. Nni - specify show nni detail information, include de-capsulated layer 2 pdu statistic. Restrictions none. Examp...

  • Page 321: 41  3

    Dgs-1210 metro ethernet managed switch cli reference guide 304 41 3 digital diagnostic monitoring commands the digital diagnostic monitoring (ddm) commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter config ddm port...

  • Page 322: Config Ddm Power_Unit

    Dgs-1210/me metro ethernet switch cli reference guide 305 to configure the port 21’s voltage threshold: dgs-1210-28p/me:5# config ddm ports 1:21 temperature_threshold high_alarm 84.9555 low_alarm -10 high_warning 70 low_warning 2.25251 command: config ddm ports 1:21 temperature_threshold high_alarm ...

  • Page 323

    Dgs-1210 metro ethernet managed switch cli reference guide 306 dgs-1210-28p/me:5# show ddm ports 1-5 vender_info command: show ddm ports 1-5 vender_info invalid ddm port list. Failure! Dgs-1210-28p/me:5#.

  • Page 327

    Dgs-1210 metro ethernet managed switch cli reference guide 310 description the config mld_snooping multicast_vlan command will create a mld multicast_vlan. Multiple multicast vlans can be configured. When creating mld multicast vlan, it cannot duplicate with the vlan entries in the existing 802.1q v...

  • Page 328

    Dgs-1210/me metro ethernet switch cli reference guide 311 multicast vlan. State – enable or disable multicast vlan for the chosen vlan. Replace_source_ipv6 – with the mld snooping function, the mld report packet sent by the host will be forwarded to the source port. Before the forwarding of the pack...

  • Page 329

    Dgs-1210 metro ethernet managed switch cli reference guide 312 restrictions only administrator, operator or power user –level users can issue this command. Example usage: to delete a mld multicast vlan: dgs-1210-28p/me:5# delete mld_snooping multicast_vlan mv1 command: delete mld_snooping multicast_...

  • Page 330

    Dgs-1210/me metro ethernet switch cli reference guide 313 example usage: to display mld snooping multicast vlan group: dgs-1210-28p/me:5# show mld_snooping multicast_vlan_group command: show mld_snooping multicast_vlan_group vid vlan name ip range ---- -------------------------------- --------------...

  • Page 331

    Dgs-1210 metro ethernet managed switch cli reference guide 314 parameters vlan_name – specifies that the mld snooping applies only to this previously created vlan. Vlanid – specifies that the mld snooping applies only to this previously created vlan id. All – specifies that mld snooping is to be con...

  • Page 332

    Dgs-1210/me metro ethernet switch cli reference guide 315 robustness_variable – provides fine-tuning to allow for expected packet loss on a subnet. The user may choose a value between 1 and 255 with a default setting of 2. If a subnet is expected to be lossy, the user may wish to increase this inter...

  • Page 333: Show Mld_Snooping

    Dgs-1210 metro ethernet managed switch cli reference guide 316 to enable the data driven learning of an mld snooping group on the default vlan: es-1210-28/me:5# config mld_snooping data_driven_learning vlan_name default state enable command: config mld_snooping data_driven_learning vlan_name default...

  • Page 334

    Dgs-1210/me metro ethernet switch cli reference guide 317 the switch. Restrictions none. Example usage: to show the mld snooping: dgs-1210-28p/me:5# show mld_snooping vlan_name default command: show mld_snooping vlan_name default mld snooping global state : enable max learned entry value : 256 vlan ...

  • Page 335: Show Mld_Snooping Group

    Dgs-1210 metro ethernet managed switch cli reference guide 318 to display the mld snooping forwarding: dgs-1210-28p/me:5# show mld_snooping forwarding all command: show mld_snooping forwarding all total entries : 0 dgs-1210-28p/me:5# show mld_snooping group purpose to display mld snooping group sett...

  • Page 336: Show Mld_Snooping Host

    Dgs-1210/me metro ethernet switch cli reference guide 319 static − displays statically configured mld router ports. Dynamic − displays dynamically configured mld router ports. Restrictions none. Example usage: to show the mld_snooping mrouterport: dgs-1210-28p/me:5# show mld_snooping mrouter_ports v...

  • Page 338

    Dgs-1210/me metro ethernet switch cli reference guide 321 profile on the switch. Restrictions only administrator or operator-level users can issue this command. Example usage: to create an ipv6 multicast filtering profile on the switch: dgs-1210-28p/me:5# create mcast_filter_profile ipv6 profile_id ...

  • Page 339: Delete McAst_Filter_Profile

    Dgs-1210 metro ethernet managed switch cli reference guide 322 name. Restrictions only administrator or operator-level users can issue this command. Example usage: to configure the multicast address range 225.1.1.1 to 225.1.1.10 to the profile name “rd3” on the switch: dgs-1210-28p/me:5# config mcas...

  • Page 342: Config Max_McAst_Group

    Dgs-1210/me metro ethernet switch cli reference guide 325 ---- ----------- -------------------------------------------------------------- 1 (v4) permit 3 (v4) permit dgs-1210-28p/me:5# config max_mcast_group purpose used to configure the maximum number of multicast groups that a port can join. Synta...

  • Page 343

    Dgs-1210 metro ethernet managed switch cli reference guide 326 3 (v6) 256 dgs-1210-28p/me:5#.

  • Page 344: 802.1X Commands

    Dgs-1210/me metro ethernet switch cli reference guide 327 44 802.1x commands the 802.1x commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter enable 802.1x disable 802.1x show 802.1x auth_state {ports } show 802.1x a...

  • Page 346: Show 802.1X

    Dgs-1210/me metro ethernet switch cli reference guide 329 success. Dgs-1210-28p/me:5# show 802.1x purpose to display the 802.1x server information on the switch. Syntax show 802.1x description the show 802.1x command displays the 802.1x port-based network access control server application on the swi...

  • Page 347

    Dgs-1210 metro ethernet managed switch cli reference guide 330 dgs-1210-28p/me:5# show 802.1x auth_state ports 1-5 command: show 802.1x auth_state ports 1-5 port auth pae state backend state port status ------ ---------------------- -------------------- --------------- 1 forceauth success authorized...

  • Page 348

    Dgs-1210/me metro ethernet switch cli reference guide 331 reauthentications. Reauthenticate: true/false − shows whether or not to reauthenticate. Parameters ports − specifies a port or range of ports to be viewed. Restrictions none. Example usage: to display the 802.1x configurations of port 2: dgs-...

  • Page 349: Config 802.1X Init

    Dgs-1210 metro ethernet managed switch cli reference guide 332 auto – allows the port’s status to reflect the outcome of the authentication process. Force_unauth – forces the authenticator for the port to become unauthorized. Network access is blocked. Quiet_period – configures the time interval bet...

  • Page 350: Config 802.1X Reauth

    Dgs-1210/me metro ethernet switch cli reference guide 333 all – specifies all of the ports on the switch. Restrictions only administrator, operator or power user-level users can issue this command. Example usage: to initialize the authentication state machine of all ports: dgs-1210-28p/me:5# config ...

  • Page 351: Config Radius Add

    Dgs-1210 metro ethernet managed switch cli reference guide 334 dgs-1210-28p/me:5# config 802.1x reauth port_based ports 1-18 command: config 802.1x reauth port_based ports 1-18 success. Dgs-1210-28p/me:5# config radius add purpose to configure the settings the switch uses to communicate with a radiu...

  • Page 352: Config Radius

    Dgs-1210/me metro ethernet switch cli reference guide 335 syntax config radius delete description the config radius delete command deletes a previously entered radius server configuration. Parameters – the index of the radius server. Restrictions only administrator or operator-level users can issue ...

  • Page 353: Show Radius

    Dgs-1210 metro ethernet managed switch cli reference guide 336 dgs-1210-28p/me:5# config radius 1 ipaddress 10.48.47.11 command: config radius 1 ipaddress 10.48.47.11 success. Dgs-1210-28p/me:5# show radius purpose to display the current radius configurations on the switch. Syntax show radius descri...

  • Page 354: Config 802.1X Auth_Mode

    Dgs-1210/me metro ethernet switch cli reference guide 337 example usage: to enable 802.1x forwarding eapol pdu dgs-1210-28p/me:5# config 802.1x fwd_pdu system enable command: config 802.1x fwd_pdu system enable success. Dgs-1210-28p/me:5# show 802.1x fwd_pdu system status purpose to display the 802....

  • Page 355: Create 802.1X Guest_Vlan

    Dgs-1210 metro ethernet managed switch cli reference guide 338 dgs-1210-28p/me:5# config 802.1x auth_mode port_based command: config 802.1x auth_mode port_based success. Dgs-1210-28p/me:5# create 802.1x guest_vlan purpose enables network access to a guest vlan. Syntax create 802.1x guest_vlan descri...

  • Page 356: Show 802.1X Guest_Vlan

    Dgs-1210/me metro ethernet switch cli reference guide 339 dgs-1210-28p/me:5# delete 802.1x guest_vlan default command: delete 802.1x guest_vlan default success. Dgs-1210-28p/me:5# config 802.1x guest_vlan ports purpose defines a port or range of ports to be members of the guest vlan. Syntax config 8...

  • Page 357: Create 802.1X User

    Dgs-1210 metro ethernet managed switch cli reference guide 340 dgs-1210-28p/me:5# show 802.1x guest_vlan command: show 802.1x guest_vlan guest vlan settings ------------------------------------------------------------------- guest vlan : default enabled guest vlan ports : 1,2,3,4,5,6 dgs-1210-28p/me...

  • Page 358: Delete 802.1X User

    Dgs-1210/me metro ethernet switch cli reference guide 341 dgs-1210-28p/me:5# show 802.1x user command: show 802.1x user index username ------------ --------------- 1 dlink total entries: 1 success. Dgs-1210-28p/me:5# delete 802.1x user purpose deletes network access to a 802.1x user. Syntax delete 8...

  • Page 359

    Dgs-1210 metro ethernet managed switch cli reference guide 342 dgs-1210-28p/me:5# config 802.1x capability ports all authenticator command: config 802.1x capability ports all authenticator success. Dgs-1210-28p/me:5#.

  • Page 361: Show Port_Security

    Dgs-1210 metro ethernet managed switch cli reference guide 344 and on when the address is aged out. Restrictions only administrator or operator-level users can issue this command example usage: to configure port security: dgs-1210-28p/me:5# config port_security 1-5 admin_state enable max_learning_ad...

  • Page 364: Show Sntp

    Dgs-1210/me metro ethernet switch cli reference guide 347 dgs-1210-28p/me:5# config sntp primary 10.1.1.1 secondary 10.1.1.2 poll- interval 60 command: config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 60 success. Dgs-1210-28p/me:5# show sntp purpose to display the sntp information. Synt...

  • Page 365: Disable Sntp

    Dgs-1210 metro ethernet managed switch cli reference guide 348 to enable the sntp function: dgs-1210-28p/me:5# enable sntp command: enable sntp success. Dgs-1210-28p/me:5# disable sntp purpose to disable sntp server support. Syntax disable sntp description the disable sntp command disables sntp supp...

  • Page 366: Config Time_Zone Operator

    Dgs-1210/me metro ethernet switch cli reference guide 349 dgs-1210-28p/me:5# config time 09jan2012 15:50:50 command: config time 09jan2012 15:50:50 success. Dgs-1210-28p/me:5# config time_zone operator purpose to determine the time zone used in order to adjust the system clock. Syntax config time_zo...

  • Page 367: Show Time

    Dgs-1210 metro ethernet managed switch cli reference guide 350 s_date - the day of the month to begin dst, expressed numerically. S_mth - the month of the year to begin dst, expressed numerically. S_time - the time of day to begin dst in hours and minutes, expressed using a 24-hour clock. End_date -...

  • Page 368

    Dgs-1210/me metro ethernet switch cli reference guide 351 dgs-1210-28p/me:5# show time command: show time time information ----------------------------------------------------------------------------------------- current time source : local current time : 01 jan 2014 15:56:02 gmt time zone offset : ...

  • Page 370: Show Arpspoofing

    Dgs-1210/me metro ethernet switch cli reference guide 353 to create an arp spoofing ip address on the switch: dgs-1210-28p/me:5# create arpspoofing ip_address 10.2.1.1 mac_address 00-00-00-01-01-2 all command: create arpspoofing ip_address 10.2.1.1 mac_address 00- 00-00-01-01-2 all success. Dgs-1210...

  • Page 371: Config Arp_Aging Time

    Dgs-1210 metro ethernet managed switch cli reference guide 354 to delete the arp spoofing configuration: dgs-1210-28p/me:5# create arpspoofing ip_address 10.2.1.1 command: create arpspoofing ip_address 10.2.1.1 success. Dgs-1210-28p/me:5# config arp_aging time purpose to configure the age-out timer ...

  • Page 372: Create Arpentry

    Dgs-1210/me metro ethernet switch cli reference guide 355 to remove dynamic entries in the arp table: dgs-1210-28p/me:5# clear arptable command: clear arptable success. Dgs-1210-28p/me:5# create arpentry purpose to create an entry for arp table on the switch. Syntax create arpentry description the c...

  • Page 373: Delete Arpentry

    Dgs-1210 metro ethernet managed switch cli reference guide 356 to configure arp entry: dgs-1210-28p/me:5# config arpentry 10.90.90.94 00-00-00-01-02-05 command: config arpentry 10.90.90.94 00-00-00-01-02-05 success. Dgs-1210-28p/me:5# delete arpentry purpose to remove the entry for arp table on the ...

  • Page 374: Show Arpentry Aging_Time

    Dgs-1210/me metro ethernet switch cli reference guide 357 to display all arp entries information on the switch: dgs-1210-28p/me:5# show arpentry information command: show arpentry information arp configurations: ------------------- maximum number of arp request retries is 3 arp cache timeout is 1800...

  • Page 375: Routing Table Commands

    Dgs-1210 metro ethernet managed switch cli reference guide 358 48 routing table commands the routing table commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter create iproute default {} delete iproute {default} show...

  • Page 376: Delete Iproute

    Dgs-1210/me metro ethernet switch cli reference guide 359 delete iproute purpose used to delete an ip route entry from the switch’s ip routing table. Syntax delete iproute {default} description the delete iproute command will delete an existing ip route entry from the switch’s ip routing table. Para...

  • Page 377: Commands

    Dgs-1210 metro ethernet managed switch cli reference guide 360 49 d-link unidirectional link detection (duld) commands the d-link unidirectional link detection (duld) commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command param...

  • Page 378: Show Duld Ports

    Dgs-1210/me metro ethernet switch cli reference guide 361 to enable unidirectional link detection on port 1: dgs-1210-28p/me:5# config duld ports 1 state enable command: config duld ports 1 state enable success. Dgs-1210-28p/me:5# show duld ports purpose to show unidirectional link detection informa...

  • Page 379: Show Duld Recover_Timer

    Dgs-1210 metro ethernet managed switch cli reference guide 362 to configure the unidirectional link detection recovery time to 100 seconds: dgs-1210-28p/me:5# config duld recover_timer 100 command: config duld recover_timer 100 success. Dgs-1210-28p/me:5# show duld recover_timer purpose to display u...

  • Page 380: Command

    Dgs-1210/me metro ethernet switch cli reference guide 363 50 ipv6 neighbor discovery commands the ipv6 neighbor discovery commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter create ipv6 neighbor_cache ipif delete i...

  • Page 381: Delete Ipv6 Neighbor_Cache

    Dgs-1210 metro ethernet managed switch cli reference guide 364 dgs-1210-28p/me:5# create ipv6 neighbor_cache ipif system 3ffc::1 00:01:02:03:04:05 command: create ipv6 neighbor_cache ipif system 3ffc::1 00:01:02:03:04:05 success. Dgs-1210-28p/me:5# delete ipv6 neighbor_cache purpose used to remove a...

  • Page 382: Show Ipv6 Nd

    Dgs-1210/me metro ethernet switch cli reference guide 365 restrictions none. Example usage: to show all neighbor cache entries on the switch: dgs-1210-28p/me:5# show ipv6 neighbor_cache ipif all all command: show ipv6 neighbor_cache ipif all all ipv6 address link-layer addr state interface ---------...

  • Page 383: Create Ipv6Route Default

    Dgs-1210 metro ethernet managed switch cli reference guide 366 other command will also change so that the values in both commands are the same. The range if 1 to 3600. Restrictions only administrator or operator-level users can issue this command. Example usage: to configure the retrans_time of ipv6...

  • Page 384: Show Ipv6Route

    Dgs-1210/me metro ethernet switch cli reference guide 367 dgs-1210-28p/me:5# delete ipv6route default command: delete ipv6route default success. Dgs-1210-28p/me:5# show ipv6route purpose used to display a static ipv6 route entry from the switch’s ip routing table. Syntax show ipv6route description t...

  • Page 385

    Dgs-1210 metro ethernet managed switch cli reference guide 368 disable ipif_ipv6_link_local_auto purpose used to disable the autoconfiguration of the ipv6 link local address. Syntax disable ipif_ipv6_link_local_auto description this disable ipif_ipv6_link_local_auto command will disable the automati...

  • Page 387: Show Log_Save_Timing

    Dgs-1210 metro ethernet managed switch cli reference guide 370 show log_save_timing purpose used to show the log save timing. Syntax show log_save_timing description this command allows display of the log save timing on the switch. Parameters none. Restrictions none. Usage example: to show the login...

  • Page 388: Command

    Dgs-1210/me metro ethernet switch cli reference guide 371 52 command history list commands the command history list commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter ? Show command_history dir each command is lis...

  • Page 389: Show Command_History

    Dgs-1210 metro ethernet managed switch cli reference guide 372 dgs-1210-28p/me:5# ? Command: ? ? Cable diagnostic port clear address_binding dhcp_snoop binding_entry ports clear arptable clear counters clear ethernet_oam ports clear fdb clear flood_fdb clear igmp_snooping data_driven_group clear log...

  • Page 390: Dir

    Dgs-1210/me metro ethernet switch cli reference guide 373 dgs-1210-28p/me:5# dir purpose to display all commands. Syntax dir description the dir command displays all commands. Parameters none. Restrictions none. Example usage: to display all of the commands: dgs-1210-28p/me:5# dir available commands...

  • Page 391: Command Logging Commands

    Dgs-1210 metro ethernet managed switch cli reference guide 374 53 command logging commands the command logging commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter enable command logging disable command logging show...

  • Page 392: Show Command Logging

    Dgs-1210/me metro ethernet switch cli reference guide 375 dgs-1210-28p/me:5# disable command logging command: disable command logging success. Dgs-1210-28p/me:5# show command logging purpose to display the switch’s general command logging configuration status. Syntax show command logging description...

  • Page 394: Disable Ssh

    Dgs-1210/me metro ethernet switch cli reference guide 377 dgs-1210-28p/me:5# enable ssh command: enable ssh success. The ssh server is enabled. Dgs-1210-28p/me:5# disable ssh purpose to disable ssh. Syntax disable ssh description the disable ssh command disables ssh on the switch. Parameters none. R...

  • Page 395: Config Ssh Authmode

    Dgs-1210 metro ethernet managed switch cli reference guide 378 example usage: to configure ssh algorithm: dgs-1210-28p/me:5# config ssh algorithm 3des enable command: config ssh algorithm 3des enable success. Dgs-1210-28p/me:5# config ssh authmode purpose to configure the ssh authentication mode set...

  • Page 396: Config Ssh Server

    Dgs-1210/me metro ethernet switch cli reference guide 379 dgs-1210-28p/me:5# show ssh authmode command: show ssh authmode the ssh authmode : ------------------------------------------------------------ password : enabled publickey : enabled hostbased : disabled success. Dgs-1210-28p/me:5# config ssh...

  • Page 397: Show Ssh Algorithm

    Dgs-1210 metro ethernet managed switch cli reference guide 380 dgs-1210-28p/me:5# show ssh server command: show ssh server the ssh server configuration : max session : 1 connection timeout : 120 authfail attempts : 20 rekey timeout : never success. Dgs-1210-28p/me:5# show ssh algorithm purpose to di...

  • Page 401: Download Ssl Certificate

    Dgs-1210 metro ethernet managed switch cli reference guide 384 example usage: to view the ssl status on the switch: dgs-1210-28p/me:5# show ssl command: show ssl ssl status enabled rsa-null-md5 0x0001 disabled rsa-null-sha1 0x0002 enabled rsa-des-sha1 0x0004 disabled rsa-3des-sha1 0x0008 disabled dh...

  • Page 402: Command

    Dgs-1210/me metro ethernet switch cli reference guide 385 56 access authentication control commands the access authentication control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter create authen_login method_l...

  • Page 404: Config Authen_Login

    Dgs-1210/me metro ethernet switch cli reference guide 387 dgs-1210-28p/me:5# create authen_login method_list_name trinity command: create authen_login method_list_name trinity success. Dgs-1210-28p/me:5# config authen_login purpose to configure a user-defined or default method list of authentication...

  • Page 405: Show Authen_Login

    Dgs-1210 metro ethernet managed switch cli reference guide 388 using the tacacs+ protocol from a remote tacacs+ server.  radius - specifies that the user is to be authenticated using the radius protocol from a remote radius server.  local - specifies that the user is to be authenticated using the ...

  • Page 406: Show Authen_Policy

    Dgs-1210/me metro ethernet switch cli reference guide 389 15>] description the show authen_login command displays a list of authentication methods for user login. Parameters default – displays the default method list for users logging on to the switch. Method_list_name - specifies the method_list_na...

  • Page 407: Config Authen_Enable

    Dgs-1210 metro ethernet managed switch cli reference guide 390 dgs-1210-28p/me:5# show authen_policy command: show authen_policy authentication policy : disabled dgs-1210-28p/me:5# create authen_enable method_list_name purpose to create a user-defined method list of authentication methods for promot...

  • Page 408

    Dgs-1210/me metro ethernet switch cli reference guide 391 the sequence of methods implemented in this command affects the authentication result. For example, if a user enters a sequence of methods like tacacs+ – radius – local_enable, the switch sends an authentication request to the first tacacs+ h...

  • Page 409: Show Authen_Enable

    Dgs-1210 metro ethernet managed switch cli reference guide 392 dgs-1210-28p/me:5# config authen_enable method_list_name trinity method tacacs+ radius local command: config authen_enable method_list_name trinity method tacacs+ radius local success. Dgs-1210-28p/me:5# delete authen_enable method_list_...

  • Page 410: Enable Authen_Policy

    Dgs-1210/me metro ethernet switch cli reference guide 393 method list name. Method name – defines which security protocols are implemeted, per method list name. Restrictions only administrator-level users can issue this command. Example usage: to display all method lists for promoting user level pri...

  • Page 411: Config Authen Application

    Dgs-1210 metro ethernet managed switch cli reference guide 394 dgs-1210-28p/me:5# disable authen_policy command: disable authen_policy success. Dgs-1210-28p/me:5# config authen application purpose to configure various applications on the switch for authentication using a previously configured method...

  • Page 412: Config Authen Parameter

    Dgs-1210/me metro ethernet switch cli reference guide 395 syntax show authen application description the show authen application command displays all of the authentication method lists (login, enable administrator privileges) for switch configuration applications (console, telnet, ssh) currently con...

  • Page 413: Show Authen Parameter

    Dgs-1210 metro ethernet managed switch cli reference guide 396 show authen parameter purpose to display authentication parameters for the various applications on the switch. Syntax show authen parameter description the show authen parameter command displays the authentication parameter on the switch...

  • Page 415: Delete Authen Server_Host

    Dgs-1210 metro ethernet managed switch cli reference guide 398 radius – specifies that the server host utilizes the radius protocol. Acct_port - specifies the accepted port number of the authentication protocol on a server host. Port – the virtual port number of the authentication protocol on a serv...

  • Page 416: Show Authen Server_Host

    Dgs-1210/me metro ethernet switch cli reference guide 399 example usage: to delete a user-defined radius authentication server host: dgs-1210-28p/me:5# delete authen server_host 10.1.1.121 protocol radius command: delete authen server_host 10.1.1.121 protocol radius success. Dgs-1210-28p/me:5# show ...

  • Page 417: Create Authen Server_Group

    Dgs-1210 metro ethernet managed switch cli reference guide 400 dgs-1210-28p/me:5# show authen server_host command: show authen server_host ip address protocol port timeout retransmit key --------------- -------------- ------ ------------ ----- ---------- -------------------- 10.1.1.121 tacacs+ 4321 ...

  • Page 419: Enable Admin

    Dgs-1210 metro ethernet managed switch cli reference guide 402 syntax show authen server_group {} description the show authen server_ group command displays user-defined authentication server groups previously created on the switch. The following parameters are displayed: group name – the name of th...

  • Page 420: Config Admin Local_Enable

    Dgs-1210/me metro ethernet switch cli reference guide 403 success. Dgs-1210-28p/me:5# config admin local_enable purpose to configure the local_enable password for administrator level privileges. Syntax config admin local_enable description the config admin local_enable command changes the locally en...

  • Page 421: Config Accounting Service

    Dgs-1210 metro ethernet managed switch cli reference guide 404 radius – specifies to use the built-in server group 'radius'. Server_group - specifies the user-defined server group. None – specifies no accounting. Restrictions only administrator-level users can issue this command. Example usage: to c...

  • Page 422

    Dgs-1210/me metro ethernet switch cli reference guide 405 command: config accounting service shell state enable radius_only success. Dgs-1210-28p/me:5# config accounting service command purpose to configure the state of the specified accounting service. Syntax config accounting service command {admi...

  • Page 423

    Dgs-1210 metro ethernet managed switch cli reference guide 406 restrictions only administrator-level users, operator and power-user level users can issue this command. Example usage: to create a user-defined accounting method list called "shell_acct": dgs-1210-28p/me:5# create accounting method_list...

  • Page 424

    Dgs-1210/me metro ethernet switch cli reference guide 407 to display all user-defined accounting method list: dgs-1210-28p/me:5# show accounting all command: show accounting all method list name priority method name comment ------------------------- ---------- --------------------- -----------------...

  • Page 425: Show Aaa

    Dgs-1210 metro ethernet managed switch cli reference guide 408 success. Dgs-1210-28p/me:5# show aaa purpose to display aaa global configuration. Syntax show aaa description the show aaa command is used to display aaa global configuration. Parameters none. Restrictions none. Example usage: to display...

  • Page 427

    Dgs-1210 metro ethernet managed switch cli reference guide 410 to display the eee state: dgs-1210-28p/me:5# show eee_mode ports 1-3 command: show eee_mode ports 1-3 port eee state ---- --------- 1 enabled 2 enabled 3 enabled success. Dgs-1210-28p/me:5#.

  • Page 428: Lacp Commands

    Dgs-1210/me metro ethernet switch cli reference guide 411 58 lacp commands the lacp commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter config lacp port_priority [timeout ] show lacp {} config lacp_ports mode [acti...

  • Page 429: Config Lacp_Ports

    Dgs-1210 metro ethernet managed switch cli reference guide 412 parameters - a port or range of ports whose lacp settings are to be displayed. If no parameter is specified, the system displays the current lacp status for all ports. Restrictions none. Example usage: to display lacp information for por...

  • Page 430

    Dgs-1210/me metro ethernet switch cli reference guide 413 dgs-1210-28p/me:5# config lacp_ports 1 mode active command: config lacp_ports 1 mode active success. Dgs-1210-28p/me:5#.

  • Page 431: Lldp Commands

    Dgs-1210 metro ethernet managed switch cli reference guide 414 59 lldp commands the lldp commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter enable lldp disable lldp config lldp message_tx_interval config lldp mess...

  • Page 432: Enable Lldp

    Dgs-1210/me metro ethernet switch cli reference guide 415 enable lldp purpose to enable lldp on the switch. Syntax enable lldp description the enable lldp command enables the link layer discovery protocol (lldp) on the switch. Parameters none. Restrictions only administrator or operator –level users...

  • Page 433: Config Lldp Reinit_Delay

    Dgs-1210 metro ethernet managed switch cli reference guide 416 dgs-1210-28p/me:5# config lldp message_tx_interval 10 command: config lldp message_tx_interval 10 success. Dgs-1210-28p/me:5# config lldp message_tx_hold_multiplier purpose to define the lldp hold-multiplier on the switch. Syntax config ...

  • Page 434: Config Lldp Tx_Delay

    Dgs-1210/me metro ethernet switch cli reference guide 417 config lldp tx_delay purpose to configure the lldp tx_delay on the switch. Syntax config lldp tx_delay description the config lldp tx_delay command specifies the delay between successive lldp frame transmissions initiated by value/status chan...

  • Page 435: Show Lldp Ports

    Dgs-1210 metro ethernet managed switch cli reference guide 418 parameters none. Restrictions none. Example usage: to show lldp settings: dgs-1210-28p/me:5# show lldp command: show lldp lldp system information chassis id subtype : mac address chassis id : 9c-d6-43-60-4f-a4 system name : 2 system desc...

  • Page 436: Show Lldp Local_Ports

    Dgs-1210/me metro ethernet switch cli reference guide 419 dgs-1210-28p/me:5# show lldp ports 1 port id : 1 ------------------------------------------------------------------------------------- admin status : tx_and_rx notification status : disable advertised tlvs option : port description disable po...

  • Page 441: Show Lldp Mgt_Addr

    Dgs-1210 metro ethernet managed switch cli reference guide 424 restrictions only administrator or operator-level users can issue this command. Example usage: to configure lldp mac_phy_configuration status: dgs-1210-28p/me:5# config lldp ports all dot1_tlv_vlan_name vlanid 1 disable command: config l...

  • Page 442: Show Lldp Power_Pse_Tlv

    Dgs-1210/me metro ethernet switch cli reference guide 425 to show the lldp statistics for port 15: dgs-1210-28p/me:5# show lldp statistics ports 15 command: show lldp statistics ports 15 port id : 15 ------------------------------------------------------------------- lldpstatstxportframestotal : 0 l...

  • Page 445

    Dgs-1210 metro ethernet managed switch cli reference guide 428 priority value in the fram e’s header. Ethernet_type – specifies that the switch examine the ethernet type value in each frame’s header. Ip - specifies that the switch examines the ip fields in each packet with special emphasis on one or...

  • Page 446: Config Access_Profile

    Dgs-1210/me metro ethernet switch cli reference guide 429 src_port_mask – specifies a udp port mask for the source port. Dst_port_mask – specifies a udp port mask for the destination port. Icmp – specifies that the switch examines the protocol field in each frame’s ip header , and that the value mus...

  • Page 448

    Dgs-1210/me metro ethernet switch cli reference guide 431 rate is implemented using the following equation – 1 value = 64kbit/sec. (ex. If the user selects a rx rate limit of 10 then the ingress rate is 640kbit/sec.) the user many select a value between 64- 1024000 or no limit. The default setting i...

  • Page 449

    Dgs-1210 metro ethernet managed switch cli reference guide 432 applies only to packets that have this udp source port in their header. Dst_port – specifies that the access profile applies only to packets that have this udp destination port in their header. Ipv6 – specifies that the switch examines t...

  • Page 450: Delete Access_Profile

    Dgs-1210/me metro ethernet switch cli reference guide 433 no limit. The default setting is no limit. Restrictions only administrator or operate-level users can issue this command. Example usage: to configure a rule for the ethernet access profile: dgs-1210-28p/me:5# config access_profile profile_id ...

  • Page 451: Create Cpu_Access_Profile

    Dgs-1210 metro ethernet managed switch cli reference guide 434 dgs-1210-28p/me:5# show access_profile profile_id 1 command: show access_profile profile_id 1 access profile table access profile id: 1 type: ethernet --------------------------------------------------------------------------- ----------...

  • Page 452: Config Cpu_Access_Profile

    Dgs-1210/me metro ethernet switch cli reference guide 435 type field. Tcp – specifies that the switch examines each frames protocol field and its value must be 6 (transmission control protocol- tcp) for the action to take place. Src_port_mask – specifies the tcp port mask for the source port. Dst_po...

  • Page 454: Delete Cpu_Access_Profile

    Dgs-1210/me metro ethernet switch cli reference guide 437 profile applies only to packets that have this tcp destination port in their header. Flag – specifies the appropriate flag parameter. Src_port –specifies that the cpu access profile applies only to packets that have this tcp source port in th...

  • Page 455: Show Cpu_Access_Profile

    Dgs-1210 metro ethernet managed switch cli reference guide 438 dgs-1210-28p/me:5# delete cpu access_profile profile_id 1 command: delete cpu access_profile profile_id 1 success. Dgs-1210-28p/me:5# show cpu_access_profile purpose to view the cpu access profile entry currently set in the switch. Synta...

  • Page 456: Show Flow_Meter

    Dgs-1210/me metro ethernet switch cli reference guide 439 burst_size - specifies the burst size rate_exceed: pecifies the action for packets that exceeds the committed rate in single rate drop_packet - drop the packet immediately. Remark_dscp - specify the remark dscp value. Restrictions only admini...

  • Page 457: Command

    Dgs-1210 metro ethernet managed switch cli reference guide 440 61 traffic segmentation commands the traffic segmentation commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter config traffic_segmentation forward_list ...

  • Page 458

    Dgs-1210/me metro ethernet switch cli reference guide 441 parameters – a port or a port channel for which the current traffic segmentation configuration on the switch is to be displayed. Restrictions none. Example usage: to display the current traffic segmentation configuration of ports 1 to 5 on th...

  • Page 460

    Dgs-1210/me metro ethernet switch cli reference guide 443 to show the safeguard engine status on the switch: dgs-1210-28p/me:5# show safeguard_engine command: show safeguard_engine safe guard : enabled dgs-1210-28p/me:5#.

  • Page 461: 63  3

    Dgs-1210 metro ethernet managed switch cli reference guide 444 63 3 device specifications this appendix contains the device specifications, and contains the following topics: technical specifications supported transceivers technical specifications performance transmission method store-and-forward pa...

  • Page 462

    Dgs-1210/me metro ethernet switch cli reference guide 445 physical and environmental standby power consumption: 10.3watts dgs-1210-20/me: maximum power consumption: 16.09watts standby power consumption: 8.80watts dgs-1210-28/me: maximum power consumption: 22.45watts standby power consumption: 17.65w...

  • Page 463

    Dgs-1210 metro ethernet managed switch cli reference guide 446 physical and environmental emi ce, fcc, c-tick, vcci, bsmi, ccc safety ul, lvd, cb general standards ieee 802.3 10base-t ethernet ieee 802.3u 100base-tx fast ethernet ieee 802.3z gigabit ethernet ieee 802.1q tagged vlan ieee 802.1p tagge...

  • Page 464

    Dgs-1210/me metro ethernet switch cli reference guide 447 general dgs-1210-28p/me: 24 x 10/100/1000 mbps ports witrh ge poe 4 x 1000mbps sfp ports dgs-1210-52/me: 48 x 10/100 /1000mbps ports 4 x 1000mbps sfp ports dgs-1210-52p/me: 48 x 10/100/1000mbps ports with port1 ~ port 24 ge poe 4 x 1000mbps s...

  • Page 465: Supported Transceivers

    Dgs-1210 metro ethernet managed switch cli reference guide 448 supported transceivers supported sfp transceivers: module description maximum distance dem-310gt sfp transceiver for 1000base-lx, single-mode fiber module 10km dem-311gt sfp transceiver for 1000base-sx, multi-mode fiber module 550m dem-3...