1. DL manuals
  2. D-Link
  3. Switch
  4. DGS-3630 SERIES
  5. Reference Manual

D-Link DGS-3630 SERIES Reference Manual

Other manuals for DGS-3630 SERIES: Hardware Installation Manual
Manual is about: Layer 3 Stackable Managed Switch Web UI Reference Guide

Summary of DGS-3630 SERIES

  • Page 2

    Information in this document is subject to change without notice. Reproduction of this document in any manner, without the written permission of the d-link corporation, is strictly forbidden. Trademarks used in this text: d-link and the d-link logo are trademarks of the d-link corporation; microsoft...

  • Page 3: Table Of Contents

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide i table of contents 1. Introduction ........................................................................................................................................................... 1 audience ............................

  • Page 4

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide ii password recovery .............................................................................................................................................. 35 login method ...................................................

  • Page 5

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide iii upload log file ............................................................................................................................................. 113 d-link discovery protocol .......................................

  • Page 6

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide iv lldp port settings ........................................................................................................................................ 205 lldp management address list .......................................

  • Page 7

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide v ospfv3 ......................................................................................................................................................... 268 ip multicast routing protocol...................................

  • Page 8

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide vi port scheduler method .................................................................................................................................. 395 queue settings ........................................................

  • Page 9

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide vii authentication sessions information ............................................................................................................. 463 authenticator statistics ....................................................

  • Page 10

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide viii ssh user settings ......................................................................................................................................... 525 ssl ..............................................................

  • Page 11

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide ix vpls mac address table ................................................................................................................................. 584 13. Monitoring ........................................................

  • Page 12

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide x dlms settings .................................................................................................................................................... 625 appendix a - password recovery procedure .....................

  • Page 13: 1.  Introduction

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 1 1. Introduction this manual’s feature descriptions are based on the software release 1.00, running in the mpls image (mi) mode. The features listed here are the subset of features that are supported by the dgs-3630 series swit...

  • Page 14

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 2 caution: a caution indicates a potential for property damage, personal injury, or death..

  • Page 15: Management Options

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 3 2. Web-based switch configuration management options logging into the web ui web user interface (web ui) management options the switch provides multiple access platforms that can be used to configure, manage, and monitor netwo...

  • Page 16: Web User Interface (Web Ui)

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 4 figure 2-1 displays entering the ip address in internet explorer after pressing the enter key, the following authentication window should appear, as shown below. Figure 2-2 web ui login window when connecting to the web ui of ...

  • Page 17

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 5 figure 2-3 main web ui window area number description area 1 this area displays a graphical, near real-time image of the front panel of the switch. This area displays the switch’s ports and expansion modules. It also shows por...

  • Page 18: 3.  System

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 6 3. System device information system information settings peripheral settings port configuration loopback test system log time and sntp time range ptp (precise time protocol) usb console settings srm device information in the d...

  • Page 19: Peripheral Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 7 figure 3-2 system information settings window the fields that can be configured in system information settings are described below: parameter description system name enter a system name for the switch, if so desired. This name...

  • Page 20: Port Configuration

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 8 figure 3-3 peripheral settings window the fields that can be configured in environment trap settings are described below: parameter description fan trap select to enable or disable the fan trap state for waning fan event (fan ...

  • Page 21

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 9 figure 3-4 port settings window the fields that can be configured are described below: parameter description unit select the stacking unit id of the switch that will be configured here. From port - to port select the appropria...

  • Page 22: Port Status

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 10 parameter description slave, and 10g. The master setting will allow the port to advertise capabilities related to duplex, speed and physical layer type. The master setting will also determine the master and slave relationship...

  • Page 23: Port Gbic

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 11 figure 3-5 port status window the fields that can be configured are described below: parameter description unit select the stacking unit id of the switch that will be displayed here. Port gbic this window is used to view acti...

  • Page 24: Error Disable Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 12 to view the following window, click system > port configuration > port auto negotiation, as shown below: figure 3-7 port auto negotiation window the fields that can be configured are described below: parameter description uni...

  • Page 25: Jumbo Frame

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 13 parameter description asserted specifies to enable or disable notifications for entering into the error disabled state. Cleared specifies to enable or disable notifications for exiting from the error disabled state. Notificat...

  • Page 26: Loopback Test

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 14 parameter description maximum receive frame size enter the maximum receive frame size value here. This value must be between 64 and 12288 bytes. By default, this value is 1536 bytes. Click the apply button to accept the chang...

  • Page 27: System Log

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 15 click the apply button to accept the changes made. System log system log settings this window is used to display and configure the system log settings. To view the following window, click system > system log > system log sett...

  • Page 28

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 16 parameter description interfaces this value is from 1 to 4094. Click the apply button to accept the changes made. The fields that can be configured for buffer log settings are described below: parameter description buffer log...

  • Page 29: System Log Server Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 17 figure 3-12 system log discriminator settings window the fields that can be configured are described below: parameter description discriminator name enter the name of the discriminator profile here. This name can be up to 15 ...

  • Page 30

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 18 the fields that can be configured are described below: parameter description host ipv4 address enter the system log server ipv4 address here. Host ipv6 address enter the system log server ipv6 address here. Udp port enter the...

  • Page 31: System Log

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 19 system log this window is used to view and clear the system log. To view the following window, click system > system log > system log, as shown below: figure 3-14 system log window click the clear log button to clear the syst...

  • Page 32: Time and Sntp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 20 time and sntp clock settings this window is used to display and configure the time settings for the switch. To view the following window, click system > time and sntp > clock settings, as shown below: figure 3-16 clock settin...

  • Page 33

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 21 figure 3-17 time zone settings window the fields that can be configured are described below: parameter description summer time state select the summer time setting. Options to choose from are disabled, recurring setting, and ...

  • Page 34: Sntp Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 22 parameter description to: week of the month select week of the month that summer time will end. To: day of the week select the day of the week that summer time will end. To: month select the month that summer time will end. T...

  • Page 35: Time Range

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 23 parameter description sntp state select this option to enable or disable sntp. Poll interval enter the synchronizing interval in seconds. The value is from 30 to 99999 seconds. The default interval is 720 seconds. Click the a...

  • Page 36: Ptp (Precise Time Protocol)

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 24 click the find button to locate a specific entry based on the information entered. Click the delete periodic button to delete the periodic entry. Click the delete button to delete the specified entry. Ptp (precise time protoc...

  • Page 37

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 25 parameter description delay of the link. The link, in this case, is connected to the port that is receiving the ptp event messages. Ports on peer-to-peer transparent clocks use the peer delay mechanism to calculate the propag...

  • Page 38: Ptp Port Global Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 26 ptp port global settings this window is used to display and configure the ptp interface settings. To view the following window, click system > ptp (precise time protocol) > ptp port global settings, as shown below: figure 3-2...

  • Page 39

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 27 figure 3-22 ptp boundary port settings window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select ...

  • Page 40: Ptp Clock Information

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 28 parameter description 1588 protocol, this value must be represented as the logarithm to the base of 2 of this time, measured in seconds. The range is from 1 to 2 seconds. Select the half second option to set 0.5 seconds as th...

  • Page 41: Ptp Port Information

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 29 figure 3-24 ptp clock information window the fields that can be configured are described below: parameter description unit select the switch unit that will be used here. Ptp port information this window is used to view ptp po...

  • Page 42: Usb Console Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 30 parameter description unit select the switch unit that will be used here. Ptp foreign master records port information this window is used to view ptp foreign master records port information. To view the following window, clic...

  • Page 43: Srm

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 31 srm the switch resource management (srm) feature provides a large number of resources that can be distributed and optimized as needed by applications. It provides resource configuration flexibility that allows users to alloca...

  • Page 44

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 32 figure 3-29 srm prefer mode window the fields that can be configured are described below: parameter description srm prefer mode select the srm prefer mode that will be used in the display here. Options to choose from are lan,...

  • Page 45: 4.  Management

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 33 4. Management command logging user accounts settings password encryption password recovery login method snmp rmon telnet/web session timeout dhcp dhcp auto configuration dhcp auto image settings dns ntp ip source interface fi...

  • Page 46

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 34 note: by default, there are no user accounts created on the switch. To view the following window, click management > user accounts settings, as shown below: after selecting the user management settings tab, the following page...

  • Page 47: Password Encryption

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 35 password encryption this window is used to display and configure whether to save the encryption of the password in the configuration file. To view the following window, click management > password encryption, as shown below: ...

  • Page 48: Login Method

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 36 login method this window is used to display and configure the login method for each management interface that is supported by the switch. To view the following window, click management > login method, as shown below: figure 4...

  • Page 49: Snmp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 37 parameter description • login local requires the user to enter a username and a password to access the specified application. Click the apply button to accept the changes made. The fields that can be configured in login passw...

  • Page 50: Snmp Global Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 38 to view read-only information or receive traps using snmpv1 while assigning a higher level of security to another group, granting read/write privileges using snmpv3. Using snmpv3, users or groups can be allowed or be prevente...

  • Page 51

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 39 parameter description snmp udp port enter the snmp udp port number. Trap source interface enter the interface whose ip address will be used as the source address for sending the snmp trap packet. The fields that can be config...

  • Page 52: Snmp View Table Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 40 parameter description from port - to port select the appropriate port range used for the configuration here. Trap sending select this option to enable or disable the sending of the snmp notification traps that are generated b...

  • Page 53

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 41 snmp community table settings this window is used to create an snmp community string to define the relationship between the snmp manager and an agent. The community string acts like a password to permit access to the agent on...

  • Page 54: Snmp Group Table Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 42 snmp group table settings an snmp group created with this table maps snmp users to the views created in the snmp view table settings window. To view the following window, click management > snmp > snmp group table settings, a...

  • Page 55: Snmp User Table Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 43 snmp engine id local settings the engine id is a unique identifier used for snmpv3 implementations on the switch. To view the following window, click management > snmp > snmp engine id local settings, as shown below: figure 4...

  • Page 56: Snmp Host Table Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 44 parameter description snmp version select the snmp version. Options to choose from are v1, v2c, and v3. Snmp v3 encryption when selecting v3 in the snmp version drop-down list, this option is available. Options to choose from...

  • Page 57

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 45 figure 4-14 snmp host table settings window the fields that can be configured are described below: parameter description host ipv4 address enter the ipv4 address of the snmp notification host. Host ipv6 address enter the ipv6...

  • Page 58: Rmon

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 46 to view the following window, click management > snmp > snmp context mapping table settings, as shown below: figure 4-15 snmp context mapping table settings window the fields that can be configured are described below: parame...

  • Page 59: Rmon Statistics Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 47 rmon statistics settings this window is used to display and configure the rmon statistics on the specified port. To view the following window, click management > rmon > rmon statistics settings, as shown below: figure 4-17 rm...

  • Page 60: Rmon Alarm Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 48 figure 4-19 rmon history settings window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. Port select the port that will b...

  • Page 61: Rmon Event Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 49 figure 4-21 rmon alarm settings window the fields that can be configured are described below: parameter description index enter the alarm index. The range is from 1 to 65535. Interval enter the interval in seconds for the sam...

  • Page 62: Telnet/web

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 50 figure 4-22 rmon event settings window the fields that can be configured are described below: parameter description index enter the index value of the alarm entry here. The range is from 1 to 65535. Description enter a descri...

  • Page 63: Session Timeout

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 51 figure 4-24 telnet/web window the fields that can be configured in telnet settings are described below: parameter description telnet state select to enable or disable the telnet server feature here. Port enter the tcp port nu...

  • Page 64: Dhcp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 52 figure 4-25 session timeout window the fields that can be configured are described below: parameter description web session timeout enter the time in seconds of the web session timeout. Tick the default check box to return to...

  • Page 65: Dhcp Class Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 53 parameter description service ipv6 dhcp state select this option to enable or disable the ipv6 dhcp relay service. Click the apply button to accept the changes made. Dhcp class settings this window is used to display and conf...

  • Page 66: Dhcp Server

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 54 parameter description match the remaining bits of the option. Bitmask enter the hex bit mask for masking of the pattern. The masked pattern bits will be matched. If not specified, all bits entered in the hex field will be che...

  • Page 67: Dhcp Server Pool Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 55 parameter description dhcp ping packet enter the number of ping packets that the switch will send out on the network containing the ip address to be allotted. If the ping request is not returned, the ip address is considered ...

  • Page 68

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 56 figure 4-31 dhcp server pool settings (edit class) window the fields that can be configured are described below: parameter description class name select an existing dhcp class name here that will be associated with this dhcp ...

  • Page 69

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 57 parameter description entered. Click the apply button to accept the changes made. Click the delete button to remove the specified entry. Click the back button to return to the previous window. After clicking the configure but...

  • Page 70

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 58 parameter description system uses broadcasts. A peer to peer (p-node) system uses only point-to- point name queries to a name server (wins). A mixed (m-node) system broadcasts first, and then queries the name server. A hybrid...

  • Page 71

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 59 figure 4-35 dhcp server manual binding window the fields that can be configured are described below: parameter description pool name enter the dhcp server pool name here. This name can be up to 32 characters long. Host enter ...

  • Page 72: Dhcp Server Ip Conflict

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 60 click the find button to locate a specific entry based on the information entered. Click the clear button to clear the entries based on the information specified. Dhcp server ip conflict this window is used to view and clear ...

  • Page 73: Dhcpv6 Server

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 61 figure 4-38 dhcp server statistic window click the clear button to clear the statistics information displayed here. Dhcpv6 server dhcpv6 server pool settings this window is used to display and configure the dhcpv6 server pool...

  • Page 74

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 62 enter a page number and click the go button to navigate to a specific page when multiple pages exist. After clicking the configure button, the following page will appear. Figure 4-40 dhcpv6 server pool settings (configure) wi...

  • Page 75

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 63 parameter description preferred lifetime. The range is from 60 to 4294967295 seconds. By default, this value is 2592000 seconds (30 days). Preferred lifetime enter the preferred lifetime value here. The range is from 60 to 42...

  • Page 76: Dhcpv6 Server Binding

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 64 to view the following window, click management > dhcp > dhcpv6 server > dhcpv6 server exclude address, as shown below: figure 4-42 dhcpv6 server exclude address window the fields that can be configured are described below: pa...

  • Page 77: Dhcp Relay

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 65 to view the following window, click management > dhcp > dhcpv6 server > dhcpv6 server interface settings, as shown below: figure 4-44 dhcpv6 server interface settings window the fields that can be configured are described bel...

  • Page 78: Dhcp Relay Pool Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 66 figure 4-46 dhcp relay global settings window the fields that can be configured are described below: parameter description dhcp relay unicast state select to globally enable or disable the dhcp relay unicast state here. Click...

  • Page 79

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 67 the fields that can be configured are described below: parameter description source ip address enter the source subnet of client packets. Subnet mask enter the network mask of the source subnet. Click the apply button to acce...

  • Page 80

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 68 parameter description class name select the dhcp class name. Click the apply button to accept the changes made. Click the edit button to edit more information. Click the delete button to remove the specified entry. Click the ...

  • Page 81

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 69 figure 4-52 dhcp relay information settings window the fields that can be configured are described below: parameter description information trust all select this option to enable or disable the dhcp relay agent to trust the i...

  • Page 82

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 70 figure 4-53 dhcp relay information option format settings window the fields that can be configured in dhcp relay information option format global are described below: parameter description information format remote id select ...

  • Page 83

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 71 click the apply button to accept the changes made. Dhcp relay information profile settings this window is used to display and configure the dhcp relay information profile settings. To view the following window, click manageme...

  • Page 84

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 72 parameter description profile name enter the option 82 profile name here. The profile can be used to define the flexible, user-defined option 82 entry. Format string after clicking the edit button, enter the user-defined dhcp...

  • Page 85: Dhcp Relay Port Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 73 parameter description string or a hexadecimal value.  svlan - indicates the outer vlan id. This can be either an ascii string or a hexadecimal value.  cvlan - indicates the inner vlan id. This can be either an ascii string ...

  • Page 86: Dhcp Local Relay Vlan

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 74 parameter description state select to enable or disable the dhcp relay feature on the specified port(s). Click the apply button to accept the changes made. Dhcp local relay vlan this window is used to display and configure lo...

  • Page 87

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 75 figure 4-57 dhcpv6 relay global settings window the fields that can be configured in dhcpv6 relay remote id settings are described below: parameter description ipv6 dhcp relay remote id format select the ipv6 dhcp relay remot...

  • Page 88

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 76 parameter description • keep - specifies that the dhcpv6 request packets that already contain the relay agent interface id option are left unchanged and directly relay to the dhcpv6 server. • drop - specifies to discard the p...

  • Page 89

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 77 figure 4-58 dhcpv6 relay interface settings window the fields that can be configured are described below: parameter description interface vlan enter the interface vlan id used in the dhcpv6 relay here. The range is from 1 to ...

  • Page 90

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 78 parameter description the following rules need to be considered: • this string can be a hexadecimal value, an ascii string, or any combination of hexadecimal values and ascii characters. An ascii string needs to be enclosed w...

  • Page 91

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 79 parameter description string or a hexadecimal value. ○ : - indicates the end of the formatted key sting. If a formatted key string is the last parameter of the command, its ending character (“:”) can be ignored. The space (0x...

  • Page 92

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 80 parameter description “keyword”+“:”: ○ % - indicates that the string that follows this character is a formatted key string. ○ “$” or “0” - (optional) indicates a fill indicator. This option specifies how to fill the formatted...

  • Page 93

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 81 parameter description “\%” is “%” itself, not the start indicator of a formatted key string. Spaces not in the formatted key string will also be encapsulated. • hexadecimal values can be any combination of formatted key strin...

  • Page 94: Dhcpv6 Local Relay Vlan

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 82 dhcpv6 relay port settings this window is used to display and configure the dhcpv6 relay port settings. To view the following window, click management > dhcp > dhcpv6 relay > dhcpv6 relay port settings, as shown below: figure...

  • Page 95: Dhcp Auto Configuration

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 83 parameter description state select to enable or disable the dhcpv6 local relay feature on the specified vlan(s) here. Click the apply button to accept the changes made. Note: when the state of the dhcpv6 relay port is disable...

  • Page 96: Dns

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 84 when the switch uses option 66 to get the tftp server name, it resolves option 6 first to get the dns server ip address. If the switch fails to connect to the dns server or option 6 does not exist in the response message, the...

  • Page 97: Dns Name Server Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 85 parameter description ip dns lookup static state select to enable or disable the ip dns lookup static state here. Ip dns lookup cache state select to enable or disable the ip dns lookup cache state here. Ip domain lookup sele...

  • Page 98: Dns Host Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 86 dns host settings this window is used to display and configure the static mapping entry for the host name and the ip address in the host table. To view the following window, click management > dns > dns host settings, as show...

  • Page 99

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 87 figure 4-69 ntp global settings window the fields that can be configured in ntp state are described below: parameter description ntp state select to globally enable or disable the ntp feature here. Click the apply button to a...

  • Page 100: Ntp Server Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 88 ntp server settings this window is used to display and configure the ntp server settings. This is used to enable the switch to synchronize time with an ntp server. To view the following window, click management > ntp > ntp se...

  • Page 101: Ntp Access Group Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 89 figure 4-71 ntp peer settings window the fields that can be configured are described below: parameter description ip address select and enter the ipv4 address of the ntp peer here. Ipv6 address select and enter the ipv6 addre...

  • Page 102: Ntp Key Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 90 figure 4-72 ntp access group settings window the fields that can be configured are described below: parameter description default select this option to specify to use the default ipv4 (0.0.0.0/0.0.0.0) or ipv6 (::/::) address...

  • Page 103: Ntp Interface Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 91 figure 4-73 ntp key settings window the fields that can be configured in ntp control key are described below: parameter description ntp control key enter the ntp control key here. This is used to define the key id for the ntp...

  • Page 104: Ntp Associations

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 92 to view the following window, click management > ntp > ntp interface settings, as shown below: figure 4-74 ntp interface settings window the fields that can be configured are described below: parameter description ntp state a...

  • Page 105: Ntp Status

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 93 figure 4-76 ntp associations (show detail) window ntp status this window is used to view ntp status information. To view the following window, click management > ntp > ntp status, as shown below: figure 4-77 ntp status window...

  • Page 106

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 94 figure 4-78 ip source interface window the fields that can be configured in ip tftp source interface are described below: parameter description source interface state select to enable or disable the ip tftp source interface s...

  • Page 107: File System

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 95 file system this window is used to view, manage and configure the switch file system. To view the following window, click management > file system, as shown below: figure 4-79 file system window the fields that can be configu...

  • Page 108: Stacking

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 96 note: if the boot configuration file is damaged, the switch will automatically revert back to the default configuration. Note: if the boot image file is damaged, the switch will automatically use the backup image file in the ...

  • Page 109

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 97 switches in the series can be physically stacked using optical fiber cables connected to sfp+ transceivers or direct attached cables (dac) with sfp+ connectors. Only the last 4 ports can be used for physical stacking. Note: w...

  • Page 110

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 98 the figure below illustrates how switches can be stacked in a duplex ring formation using optical fiber cables connected to sfp+ transceivers or dac with sfp+ connectors where the 2-port stacking configuration is used. Figure...

  • Page 111

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 99 primary master - the primary master is the leader of the stack. It will maintain normal operations, monitor operations and the running topology of the stack. This switch will also assign stack unit ids, synchronize configurat...

  • Page 112: Physical Stacking

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 100 databases, such as arp, will also be cleared. Then the backup master will begin backing up the primary master when the database synchronization has been completed by the stack. If the primary master is removed, the backup ma...

  • Page 113: Stacking Bandwidth

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 101 parameter description trap state select this option to enable or disable stacking related snmp traps. Click the apply button to accept the changes made. The fields that can be configured in stack id are described below: para...

  • Page 114: Virtual Stacking (Sim)

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 102 figure 4-85 stacking bandwidth window the fields that can be configured are described below: parameter description stack bandwidth select the stacking bandwidth here. Option to choose from are: • 2-port - specifies 2 switch ...

  • Page 115

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 103 the sim group is a group of switches that are managed as a single entity. The switch may take on three different roles: 1. Commander switch (cs) - this is a switch that has been manually configured as the controlling device ...

  • Page 116: Single Ip Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 104 the topology map now includes new features for connections that are a member of a port trunking group. It will display the speed and number of ethernet connections creating this port trunk group. This version will support sw...

  • Page 117: Topology

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 105 parameter description for sim. Group name enter a group name. This is optional. This name is used to segment switches into different sim groups. Click the apply button to accept the changes made. The fields that can be confi...

  • Page 118

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 106 figure 4-87 topology window the fields that can be configured are described below: parameter description device name display the device name of the switches in the sim group configured by the user. If the device is not confi...

  • Page 119

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 107 figure 4-88 topology view this window will display how the devices within the single ip management group connect to other groups and devices. Possible icons on this window are as follows: icon description icon description gr...

  • Page 120

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 108 figure 4-89 device information utilizing the tool tip setting the mouse cursor over a line between two devices will display the connection speed between the two devices, as shown below. Figure 4-90 port speed utilizing the t...

  • Page 121

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 109 figure 4-91 right-clicking a group icon the following options may appear for the user to configure: • collapse - to collapse the group that will be represented by a single icon. • expand - to expand the sim group, in detail....

  • Page 122

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 110 click the close button to close the property window. Commander switch icon figure 4-93 right-clicking a commander icon the following options may appear for the user to configure: • collapse - to collapse the group that will ...

  • Page 123

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 111 • add to group - add a candidate to a group. Clicking this option will reveal the following dialog box for the user to enter a password for authentication from the candidate switch before being added to the sim group. Click ...

  • Page 124: Firmware Upgrade

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 112 figure 4-99 about window firmware upgrade this window is used to view and upgrade firmware from the commander switch to the member switch. Member switches will be listed in the table. To view the following window, click mana...

  • Page 125: Upload Log File

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 113 figure 4-101 configuration file backup/restore window the fields that can be configured are described below: parameter description tftp server ip enter the tftp server ip address. Path \ filename enter the path and file name...

  • Page 126: Smtp Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 114 figure 4-103 d-link discovery protocol window the fields that can be configured in d-link discovery protocol are described below: parameter description d-link discovery protocol state select to globally enable or disable the...

  • Page 127

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 115 figure 4-104 smtp settings window the fields that can be configured in smtp global settings are described below: parameter description smtp ip select the smtp server ip address type here. Options to choose from are ipv4 and ...

  • Page 128: Reboot Schedule Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 116 parameter description characters long. Click the add button to add a new smtp email recipient. The fields that can be configured in send a test mail to all are described below: parameter description subject enter the subject...

  • Page 129: Nlb Fdb Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 117 click the delete button to remove the specified reboot schedule. Nlb fdb settings this window is used to display and configure the network load balancing (nlb) fdb settings. The network load balancing (nlb) function is used ...

  • Page 130: Sd Card Management

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 118 sd card management this section refers to the configuration associated with removable devices which includes usb driver storage. Sd card backup settings this window is used to display and configure the sd card backup setting...

  • Page 131

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 119 figure 4-108 sd card execute settings window the fields that can be configured in execute configuration are described below: parameter description file url enter the url of the file here. If the current directory is not the ...

  • Page 132: 5.  Layer 2 Features

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 120 5. Layer 2 features fdb vlan vlan tunnel stp erps (g.8032) loopback detection link aggregation flex links l2 protocol tunnel l2 multicast control lldp fdb static fdb unicast static fdb this window is used to display and conf...

  • Page 133: Multicast Static Fdb

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 121 multicast static fdb this window is used to display and configure the multicast static fdb settings. To view the following window, click l2 features > fdb > static fdb > multicast static fdb, as shown below: figure 5-2 multi...

  • Page 134

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 122 parameter description value is 300 seconds. Aging destination hit select to enable or disable the aging destination hit function. Click the apply button to accept the changes made. After selecting the mac address port learni...

  • Page 135: Mac Address Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 123 the fields that can be configured are described below: parameter description vid list enter the vlan id(s) that will be used in this configuration or display here. A series of vlan ids can be entered separated by commas or a...

  • Page 136: Mac Notification

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 124 click the find button to locate a specific entry based on the information entered. Click the clear all button to clear all dynamic mac addresses. Click the show all button to display all the mac addresses recorded in the mac...

  • Page 137: Vlan

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 125 click the apply button to accept the changes made for each individual section. After selecting the mac notification history tab, at the top of the page, the following page will be available. Figure 5-8 mac notification (mac ...

  • Page 138: 802.1V Protocol Vlan

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 126 click the delete button to remove the specific entry. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. 802.1v protocol vlan protocol vlan profile this window is used to di...

  • Page 139: Gvrp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 127 figure 5-11 protocol vlan profile interface window the fields that can be configured are described below: parameter description port select the stacking unit id and the port number of the switch that will be configured here....

  • Page 140: Gvrp Port

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 128 gvrp port this window is used to display and configure the gvrp port settings. To view the following window, click l2 features > vlan > gvrp > gvrp port, as shown below: figure 5-13 gvrp port window the fields that can be co...

  • Page 141: Gvrp Forbidden Vlan

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 129 figure 5-14 gvrp advertise vlan window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the ra...

  • Page 142: Gvrp Statistics Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 130 parameter description from port - to port select the range of ports that will be used for this configuration here. Action select the forbidden vlan to port mapping action that will be taken here. Options to choose from are a...

  • Page 143: Mac Vlan

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 131 figure 5-17 asymmetric vlan window the fields that can be configured are described below: parameter description asymmetric vlan state select to enable or disable the asymmetric vlan feature here. Click the apply button to ac...

  • Page 144

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 132 figure 5-19 vlan interface window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. Click the show detail button to view m...

  • Page 145

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 133 figure 5-21 vlan interface (access) window the fields that can be configured are described below: parameter description vlan mode select the vlan mode option here. Options to choose from are access, hybrid, trunk, 802.1q-tun...

  • Page 146

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 134 parameter description secondary. Acceptable frame select the acceptable frame behavior option here. Options to choose from are tagged only, untagged only, and admit all. Ingress checking select to enable or disable the ingre...

  • Page 147

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 135 parameter description vid after ticking the native vlan option the following parameter will be available. Enter the vlan id used for this configuration here. This value must be between 1 and 4094. Action select the action th...

  • Page 148

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 136 click the apply button to accept the changes made. Click the back button to discard the changes made and return to the previous page. When promiscuous was selected as the vlan mode, the following page will appear. Figure 5-2...

  • Page 149

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 137 parameter description clone select this option to enable the clone feature. From port - to port select the range of ports that will be used in the clone feature here. Click the apply button to accept the changes made. Click ...

  • Page 150

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 138 figure 5-28 vlan interface (trunk secondary) window the fields that can be configured are described below: parameter description vlan mode select the vlan mode option here. Options to choose from are access, hybrid, trunk, 8...

  • Page 151: Subnet Vlan

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 139 figure 5-29 l2vlan interface description window the fields that can be configured are described below: parameter description l2vlan interface enter the id of the layer 2 vlan interface here. Description enter the description...

  • Page 152: Super Vlan

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 140 parameter description length here. Ipv6 network prefix / prefix length select and enter the ipv6 address and prefix length value for the subnet vlan here. Vid enter the vlan id for the subnet vlan here. Priority select the p...

  • Page 153: Auto Surveillance Vlan

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 141 click the apply button to accept the changes made. The fields that can be configured in find super vlan are described below: parameter description super vid enter the super vlan id that will be displayed here. The range is f...

  • Page 154

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 142 figure 5-33 auto surveillance properties window the fields that can be configured in global settings are described below: parameter description surveillance vlan select to enable or disable the surveillance vlan feature here...

  • Page 155

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 143 click the apply button to accept the changes made. Mac settings and surveillance device this window is used to display and configure surveillance devices and their mac settings. To view the following window, click l2 feature...

  • Page 156: Voice Vlan

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 144 figure 5-35 mac settings and surveillance device (auto surveillance vlan summary) window the fields that can be configured are described below: parameter description unit select the stacking unit id of the switch that will b...

  • Page 157: Voice Vlan Port

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 145 click the apply button to accept the changes made. Voice vlan port this window is used to display and configure the voice vlan interface settings. To view the following window, click l2 features > vlan > voice vlan > voice v...

  • Page 158: Voice Vlan Oui

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 146 voice vlan oui this window is used to display and configure the voice vlan oui settings. Use this window to add a user-defined oui for the voice vlan. The oui for the voice vlan is used to identify the voice traffic by using...

  • Page 159: Private Vlan

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 147 the fields that can be configured are described below: parameter description unit select the switch unit that will be used in this display here. Voice vlan lldp-med device this window is used to view the voice vlan lldp-med ...

  • Page 160: Vlan Tunnel

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 148 parameter description type select the type of private vlan that will be created here. Options to choose from are community, isolated, and primary. Click the apply button to accept the changes made. The fields that can be con...

  • Page 161

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 149 only configure the 802.1q tunneling ethernet type on ports that are connected to the provider bridge network, which receives and transmits the service vlan tagged frames. If the tunnel ethernet type is configured, the specif...

  • Page 162: Vlan Mapping

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 150 figure 5-43 dot1q tunnel settings (dot1q tunnel port settings) window the fields that can be configured are described below: parameter description unit select the switch unit id that will be used here. From port - to port se...

  • Page 163: Vlan Mapping Profile

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 151 figure 5-44 vlan mapping settings window the fields that can be configured are described below: parameter description unit select the switch unit id that will be used here. From port - to port select the port range that will...

  • Page 164

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 152 figure 5-45 vlan mapping profile window the fields that can be configured are described below: parameter description profile id enter the id of the vlan mapping profile here. A lower id has a higher priority. The id range is...

  • Page 165

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 153 figure 5-46 vlan mapping profile (ethernet, add rule) window the fields that can be configured are described below: parameter description rule id enter the vlan mapping rule id here. If not specified, the rule id begins from...

  • Page 166

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 154 figure 5-47 vlan mapping profile (ip, add rule) window the fields that can be configured are described below: parameter description rule id enter the vlan mapping rule id here. If not specified, the rule id begins from 10 an...

  • Page 167

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 155 figure 5-48 vlan mapping profile (ipv6, add rule) window the fields that can be configured are described below: parameter description rule id enter the vlan mapping rule id here. If not specified, the rule id begins from 10 ...

  • Page 168

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 156 figure 5-49 vlan mapping profile (ethernet-ip, add rule) window the fields that can be configured are described below: parameter description rule id enter the vlan mapping rule id here. If not specified, the rule id begins f...

  • Page 169: Stp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 157 parameter description new inner vid after selecting dot1q-tunnel as the action, enter the new inner vlan id here. The range is from 1 to 4094. This option is only available when dot1q-tunnel was selected as the action. Click...

  • Page 170

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 158 version compatible with ieee 802.1d-1998. Rstp can operate with legacy equipment implementing ieee 802.1d- 1998, however the advantages of using rstp will be lost. This section introduces some new spanning tree concepts and ...

  • Page 171: Stp Global Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 159 stp global settings this window is used to display and configure the global stp settings. To view the following window, click l2 features > stp > stp global settings, as shown below: figure 5-50 stp global settings window th...

  • Page 172: Stp Port Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 160 parameter description this value is 32768. The lower the value, the higher the priority. Click the apply button to accept the changes made. The fields that can be configured for stp configuration are described below: paramet...

  • Page 173

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 161 figure 5-51 stp port settings window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the rang...

  • Page 174

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 162 parameter description option is disabled. Bpdu forward select to enable or disable bpdu forwarding. If enabled, the received stp bpdu will be forwarded to all vlan member ports in the untagged form. By default, this option i...

  • Page 175: Stp Instance

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 163 the fields that can be configured for mst configuration identification are described below: parameter description configuration name enter the mst. This name uniquely identifies the msti (multiple spanning tree instance). If...

  • Page 176: Mstp Port Information

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 164 click the edit button to re-configure the specific entry. Click the apply button to accept the changes made. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. Mstp port inf...

  • Page 177

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 165 note: be aware that changing the erps version will lead to the restart of the running protocol. To view the following window, click l2 features > erps (g.8032) > erps, as shown below: figure 5-55 erps window the fields that ...

  • Page 178

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 166 the fields that can be configured in ethernet ring g.8032 are described below: parameter description ring name enter the ethernet ring protection (erp) instance name here. This name can be up to 32 characters long. Click the...

  • Page 179

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 167 click the back button to discard the changes made and return to the previous window. Click the apply button to accept the changes made. After click the show detail button, the following window will appear. Figure 5-57 erps (...

  • Page 180

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 168 figure 5-59 erps (erps brief, edit instance) window the fields that can be configured are described below: parameter description description select the checkbox and enter the erp instance description here. This description c...

  • Page 181: Erps Profile

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 169 parameter description active this erp instance. Sub ring instance select the checkbox and enter the identifier of the erp instance here. This is used to specify the sub-ring instance of a physical ring instance. The range is...

  • Page 182: Loopback Detection

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 170 figure 5-61 erps profile (edit) window the fields that can be configured are described below: parameter description tcn propagation select the checkbox and then select the tcn propagation state. Options to choose from are en...

  • Page 183

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 171 figure 5-62 loopback detection window the fields that can be configured in loopback detection global settings are described below: parameter description loopback detection state select to enable or disable loopback detection...

  • Page 184: Link Aggregation

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 172 link aggregation understanding port trunk groups port trunk groups are used to combine a number of ports together to make a single high-bandwidth data pipeline. The switch supports up to 32 port trunk groups with up to 12 po...

  • Page 185

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 173 figure 5-64 link aggregation window the fields that can be configured for link aggregation are described below: parameter description system priority enter the system priority value used here. This value must be between 1 an...

  • Page 186: Flex Links

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 174 figure 5-65 link aggregation (channel detail) window the fields that can be configured are described below: parameter description description enter the description for the port channel here. This string can be up to 64 chara...

  • Page 187: L2 Protocol Tunnel

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 175 figure 5-66 l2 flex links window the fields that can be configured are described below: parameter description unit select the switch unit of the primary port here. Primary port select the primary port here. Unit select the s...

  • Page 188

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 176 parameter description by default, this value is 0. The tunneling of the layer 2 protocol packets will consume cpu processing power in encapsulating, decapsulating, and forwarding of the packet. Use this option to restrict th...

  • Page 189: L2 Multicast Control

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 177 parameter description from are 01-00-0c-cc-cc-cc and 01-00-0c-cc-cc-cd. Threshold after selecting the shutdown or drop option in the type field, the following parameter will be available. Enter the threshold value here. This...

  • Page 190

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 178 parameter description vid enter a vlan id from 1 to 4094, and select to enable or disable igmp snooping on the vlan. Click the apply button to accept the changes made. The fields that can be configured in igmp snooping table...

  • Page 191

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 179 figure 5-71 igmp snooping settings (modify, edit) window the fields that can be configured are described below: parameter description minimum version select the minimum igmp host version that is allowed on the vlan. Options ...

  • Page 192

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 180 parameter description rate limit enter the rate limit value here. The range is from 1 to 1000. Tick the no limit option to apply no rate limit on this profile. Ignore topology change select to enable or disable the ignore to...

  • Page 193

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 181 to view the following window, click l2 features > l2 multicast control > igmp snooping > igmp snooping groups settings, as shown below: figure 5-73 igmp snooping groups settings window the fields that can be configured in ig...

  • Page 194

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 182 igmp snooping filter settings this window is used to display and configure the igmp snooping filter settings. To view the following window, click l2 features > l2 multicast control > igmp snooping > igmp snooping filter sett...

  • Page 195

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 183 parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the appropriate port range used for the configuration here. Limit number enter the limit number here...

  • Page 196

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 184 after clicking the please select button, the following page will appear. Figure 5-75 igmp snooping filter settings (please select) window select the acl and click the ok button to use the selected access list. Enter a page n...

  • Page 197

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 185 parameter description vid enter the vlan id used here. The range is from 1 to 4094. Configuration select the port configuration. Options to choose from are port, and forbidden port. • port - select to have the configured por...

  • Page 198: Mld Snooping

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 186 parameter description when port is selected in the statistics drop-down list. From port - to port select the appropriate port range used for the configuration here. This is available when port is selected in the statistics d...

  • Page 199: Mld Snooping Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 187 • multicast listener report, version 2 - comparable to the host membership report in igmpv3, and labeled as 143 in the icmp packet header, this message is sent by the listening port to the switch stating that it is intereste...

  • Page 200

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 188 after clicking the show detail button, the following window will appear. Figure 5-80 mld snooping settings (show detail) window the window displays the detail information about mld snooping vlan. Click the modify button to e...

  • Page 201

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 189 parameter description minimum version select the minimum version of mld hosts that is allowed on the vlan. Options to choose from are 1 and 2. Fast leave select this option to enable or disable the mld snooping fast leave fu...

  • Page 202

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 190 figure 5-82 mld snooping groups settings window the fields that can be configured in mld snooping static groups settings are described below: parameter description vid enter the vlan id of the multicast group here. The range...

  • Page 203

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 191 to view the following window, click l2 features > l2 multicast control > mld snooping > mld snooping filter settings, as shown below: figure 5-83 mld snooping filter settings window the fields that can be configured in mld s...

  • Page 204

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 192 parameter description limit number enter the limit number here. This is used to set the limitation on the number of mld cache entries that can be created. The range is from 1 to 4096. Exceed action select the exceed action h...

  • Page 205

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 193 figure 5-84 mld snooping filter settings (please select) window select the acl and click the ok button to use the selected access list. Enter a page number and click the go button to navigate to a specific page when multiple...

  • Page 206

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 194 parameter description vid enter a vlan id between 1 and 4094. Configuration select the port configuration. Options to choose from are port, forbidden port, and learn pimv6. • port - select to have the configured ports as bei...

  • Page 207: Multicast Vlan

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 195 parameter description unit select the switch unit that will be used for this configuration here. This is available when port is selected in the statistics drop-down list. From port - to port select the appropriate port range...

  • Page 208

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 196 figure 5-88 multicast vlan settings window the fields that can be configured in multicast vlan global settings are described below: parameter description multicast vlan ipv4 state select to enable or disable the ipv4 igmp co...

  • Page 209

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 197 the fields that can be configured in member port settings are described below: parameter description vid enter the multicast vlan id that will be used here. The range is 2 to 4094. Action select add to add a new entry based ...

  • Page 210

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 198 parameter description from select the “from” option here. Options to choose from are receiver, source, and both. • receiver - specifies that the source ipv4/ipv6 address of the igmp/mld report/leave packet received on any mu...

  • Page 211

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 199 figure 5-89 multicast vlan group settings window the fields that can be configured in group profile settings are described below: parameter description profile name enter the group profile name for the multicast vlan feature...

  • Page 212: Pim Snooping

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 200 click the apply button to accept the changes made. The fields that can be configured in group profile table are described below: parameter description profile name enter the group profile name for the multicast vlan feature ...

  • Page 213: Pim Snooping Mroute Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 201 click the apply button to accept the changes made. The fields that can be configured in vlan status settings are described below: parameter description vid enter the vlan id on which the pim snooping feature will be used her...

  • Page 214: Multicast Filtering

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 202 figure 5-92 pim snooping mroute table window the fields that can be configured are described below: parameter description vid select and enter the vlan id that will be used in this display here. The range is from 1 to 4094. ...

  • Page 215: Lldp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 203 figure 5-94 multicast filtering window the fields that can be configured are described below: parameter description vid list enter the vlan id list that will be used for this configuration here. Multicast filter mode select ...

  • Page 216

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 204 figure 5-95 lldp global settings window the fields that can be configured in lldp global settings are described below: parameter description lldp state select this option to enable or disable the lldp feature lldp forward st...

  • Page 217: Lldp Port Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 205 parameter description each physical interface. The range is from 5 to 32768 seconds. Message tx hold multiplier enter the multiplier on the lldpdus transmission interval that used to calculate the ttl value of an lldpdu. Thi...

  • Page 218: Lldp Basic Tlvs Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 206 parameter description are default, ipv4 and ipv6. Action select the action that will be taken here. Options to choose from are remove and add. Address enter the ip address that will be sent. Click the apply button to accept ...

  • Page 219: Lldp Dot1 Tlvs Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 207 figure 5-98 lldp basic tlvs settings window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select t...

  • Page 220: Lldp Dot3 Tlvs Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 208 parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the appropriate port range used for the configuration here. Port vlan select this option to enable o...

  • Page 221: Lldp-Med Port Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 209 parameter description maximum frame size select this option to enable or disable the maximum frame size tlv to send. The maximum frame size tlv indicates the maximum frame size capability of the implemented mac and phy. Ener...

  • Page 222

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 210 figure 5-102 lldp-dcbx port settings window the fields that can be configured are described below: parameter description unit select the switch unit id that will be used here. From port - to port select the switch port range...

  • Page 223

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 211 the fields that can be configured are described below: parameter description unit select the switch unit that will be used here. Port select the port number that will be used here. Click the clear counter button to clear the...

  • Page 224

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 212 figure 5-105 lldp local port information (show detail) window to view more details about, for example, the mac/phy configuration/status, click the show detail hyperlink. Click the back button to return to the previous window...

  • Page 225

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 213 figure 5-107 lldp neighbor port information window the fields that can be configured are described below: parameter description unit select the switch unit that will be displayed. Port select the port number that will be dis...

  • Page 226: 6.  Layer 3 Features

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 214 6. Layer 3 features arp gratuitous arp ipv6 neighbor interface udp helper ipv4 static/default route ipv4 static route bfd ipv4 route table ipv6 static/default route ipv6 static route bfd ipv6 route table route preference ecm...

  • Page 227: Arp Aging Time

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 215 arp aging time this window is used to display and configure the arp aging time settings. To view the following window, click l3 features > arp > arp aging time, as shown below: figure 6-2 arp aging time window the fields tha...

  • Page 228: Proxy Arp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 216 enter a page number and click the go button to navigate to a specific page when multiple pages exist. Proxy arp this window is used to display and configure the proxy arp settings. The proxy arp feature will allow the switch...

  • Page 229: Gratuitous Arp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 217 parameter description vrf name enter the name of the vrf instance here. This name can be up to 12 characters long. Interface vlan enter the interface vlan id used here. This value must be between 1 and 4094. Ip address selec...

  • Page 230: Ipv6 Neighbor

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 218 parameter description gratuitous arp packets. The gratuitous arp packet is sent by a source ip address and is identical to the ip that the packet is querying. Click the apply button to accept the changes made. Click the edit...

  • Page 231: Interface

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 219 interface ipv4 interface this window is used to display and configure the ipv4 interface settings. To view the following window, click l3 features > interface > ipv4 interface, as shown below: figure 6-8 ipv4 interface windo...

  • Page 232

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 220 the fields that can be configured are described below: parameter description state select to enable or disable the ipv4 interface global state. Ip vrf forwarding enter the vrf instance name that will be forwarded here. Ip mt...

  • Page 233: Ipv6 Interface

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 221 parameter description dhcp discover message. Lease enter and optionally select the dhcp client lease time here. In the text box the lease time, in days, can be entered. The range is from 0 to 10000 days. Hours and minutes ca...

  • Page 234

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 222 figure 6-12 ipv6 interface (detail, ipv6 interface settings) window the fields that can be configured are described below: parameter description ipv6 mtu enter the ipv6 mtu value here. The range is from 1280 to 65534 bytes. ...

  • Page 235

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 223 parameter description 3600000 milliseconds, in multiples of 1000. If the specified time is 0, the router will use 1 second on the interface and advertise 0 (unspecified) in the router advertisement (ra) message. Click the ap...

  • Page 236: Loopback Interface

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 224 after selecting the dhcpv6 client tab option, at the top of the page, the following page will be available. Figure 6-15 ipv6 interface (detail, dhcpv6 client) window click the restart button to restart the dhcpv6 client serv...

  • Page 237

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 225 figure 6-16 loopback interface window the fields that can be configured are described below: parameter description interface loopback enter the loopback interface id here. The range is from 1 to 8. Click the apply button to ...

  • Page 238: Null Interface

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 226 click the apply button to accept the changes made. Click the delete button to delete the specified entry. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. Null interface t...

  • Page 239: Ip Helper Address

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 227 the fields that can be configured are described below: parameter description ip forward protocol udp port enter the destination port of the udp service to be forwarded here. The range is from 1 to 65535. Click the apply butt...

  • Page 240: Ipv4 Static/default Route

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 228 ipv4 static/default route this window is used to display and configure the ipv4 static and default route settings. The switch supports static routing for ipv4 formatted addressing. Users can create up to 512 static route ent...

  • Page 241: Ipv4 Static Route Bfd

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 229 click the delete button to remove the specific entry. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. Ipv4 static route bfd this window is used to display and configure t...

  • Page 242: Ipv6 Static/default Route

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 230 parameter description vrf name enter the name of the vrf instance here. This name can be up to 12 characters long. Ip address select and enter the single ipv4 address here. Network address select and enter the ipv4 network a...

  • Page 243: Ipv6 Static Route Bfd

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 231 parameter description default administrative distance for a static route is 1. Backup state select the backup state option here. Options to choose from are primary, and backup. When the primary option is selected, the route ...

  • Page 244: Route Preference

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 232 figure 6-26 ipv6 route table window the fields that can be configured are described below: parameter description ipv6 address select and enter the ipv6 address to display here. Ipv6 address/prefix length select and enter the...

  • Page 245: Ecmp Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 233 parameter description vrf name enter the name of the vrf instance here. This name can be up to 12 characters long. Click the please select button to select a pre-configured vrf instance that will be used here. Distance defau...

  • Page 246: Ipv6 General Prefix

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 234 parameter description crc 32 upper select this option to use the upper bits of crc-32 as the ecmp hashing algorithm. Tcp/udp port select this option to use tcp/udp port number as ecmp hash key. Click the apply button to acce...

  • Page 247: Ip Tunnel Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 235 ip tunnel settings this window is used to display and configure the ip tunnel settings. To view the following window, click l3 features > ip tunnel settings, as shown below: figure 6-31 ip tunnel settings window the fields t...

  • Page 248: Urpf Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 236 parameter description tunnel mode select the tunnel mode here. Options to choose from are ipv6 ip, 6to4, isatap, gre ip, and gre ipv6. • ipv6 ip - specifies that the interface is an ipv6 ip tunnel interface. • 6to4 - specifi...

  • Page 249

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 237 the fields that can be configured in urpf global settings are described below: parameter description urpf state select to globally enable or disable the urpf state here. Click the apply button to accept the changes made. Not...

  • Page 250: Vrf

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 238 vrf vrf settings this window is used to display and configure the virtual routing and forwarding (vrf) settings. To view the following window, click l3 features > vrf > vrf settings, as shown below: figure 6-34 vrf settings ...

  • Page 251

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 239 click the back button to return to the previous window. The fields that can be configured in vrf max routes settings are described below: parameter description max routes enter the maximum number of routes within the vrf her...

  • Page 252: Vrf Interface Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 240 figure 6-36 vrf settings (show detail) window click the back button to return to the previous window. After clicking the show detail link, the following page will appear. Figure 6-37 vrf settings (show detail, show detail) w...

  • Page 253: Rip

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 241 figure 6-38 vrf interface settings window the fields that can be configured in vrf interface settings are described below: parameter description interface vlan enter the id of the vlan interface here. The range is from 1 to ...

  • Page 254

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 242 figure 6-39 rip settings window the fields that can be configured in rip global settings are described below: parameter description rip state select to globally enable or disable the routing information protocol (rip) featur...

  • Page 255

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 243 figure 6-40 rip settings (edit) window click the back button to return to the previous window. The fields that can be configured in redistribution configuration are described below: parameter description redistribution • fir...

  • Page 256: Rip Distribute List

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 244 parameter description to rip. The specifying of the metric allows the metric to be synced. Select the default option to use the default metric value, which is 0. Version select the global rip version that will be used as the...

  • Page 257: Rip Interface Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 245 click the back button to return to the previous window. Rip interface settings this window is used to display and configure the rip interface settings. To view the following window, click l3 features > rip > rip interface se...

  • Page 258: Ripng

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 246 figure 6-44 rip database window the fields that can be configured are described below: parameter description network address enter the subnet prefix and the prefix length of the network(s) to be displayed here. Vrf name ente...

  • Page 259

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 247 the fields that can be configured in ripng global settings are described below: parameter description global state select to globally enable or disable the ripng feature here. Click the apply button to accept the changes mad...

  • Page 260: Ripng Interface Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 248 ripng interface settings this window is used to display and configure the ripng interface settings. To view the following window, click l3 features > ripng > ripng interface settings, as shown below: figure 6-46 ripng interf...

  • Page 261: Ospf

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 249 parameter description ipv6 address/prefix length enter the ipv6 address that will be used for these results here. Click the find button to locate a specific entry based on the information entered. Ospf ospfv2 ospfv2 process ...

  • Page 262

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 250 select the vrf entry and click the ok button to use the selected vrf entry. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. After clicking the edit button, the following ...

  • Page 263: Ospfv2 Distribute List

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 251 figure 6-51 ospfv2 process settings (show detail) window the fields that can be configured are described below: parameter description compatible rfc3509 select to enable or disable the implementation of area border router (a...

  • Page 264: Ospfv2 Gr Helper Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 252 figure 6-52 ospfv2 distribute list window the fields that can be configured are described below: parameter description vrf name enter the name of the vrf instance here. This name can be up to 12 characters long. Click the se...

  • Page 265

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 253 figure 6-54 ospfv2 gr helper settings window the fields that can be configured are described below: parameter description vrf name enter the name of the vrf instance here. This name can be up to 12 characters long. Click the...

  • Page 266: Ospfv2 Area Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 254 figure 6-56 ospfv2 passive interface settings window the fields that can be configured are described below: parameter description vrf name enter the name of the vrf instance here. This name can be up to 12 characters long. C...

  • Page 267

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 255 figure 6-58 ospfv2 area settings window the fields that can be configured in ospf area settings are described below: parameter description vrf name enter the name of the vrf instance here. This name can be up to 12 character...

  • Page 268: Ospfv2 Interface Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 256 after clicking the select vrf button, the following page will appear. Figure 6-59 ospfv2 area settings (select vrf) window select the vrf entry and click the ok button to use the selected vrf entry. Enter a page number and c...

  • Page 269

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 257 figure 6-61 ospfv2 interface settings window the fields that can be configured in ospf interface settings are described below: parameter description vrf name enter the name of the vrf instance here. This name can be up to 12...

  • Page 270

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 258 figure 6-62 ospfv2 interface settings (show detail) window the fields that can be configured are described below: parameter description cost enter the cost value here. The range is from 1 to 65535. The interface cost reflect...

  • Page 271

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 259 parameter description become the dr, the router with the higher router priority will be elected the dr. If the routers have the same priority, the router with the higher router id takes precedence. Only routers with non-zero...

  • Page 272: Ospfv2 Bfd Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 260 select the vrf entry and click the ok button to use the selected vrf entry. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. Ospfv2 bfd settings this window is used to dis...

  • Page 273

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 261 figure 6-65 ospfv2 redistribute settings window the fields that can be configured are described below: parameter description vrf name enter the name of the vrf instance here. This name can be up to 12 characters long. Click ...

  • Page 274

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 262 ospfv2 virtual link settings this window is used to display and configure ospfv2 virtual link settings. If a non-zero area is not physically connected to the zero area, it must be connected to the zero area via a virtual lin...

  • Page 275: Ospfv2 Lsdb Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 263 the fields that can be configured in ospf virtual link table are described below: parameter description vrf name enter the name of the vrf instance here. This name can be up to 12 characters long. Click the select vrf button...

  • Page 276

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 264 figure 6-70 ospfv2 lsdb table window the fields that can be configured are described below: parameter description vrf name enter the name of the vrf instance here. This name can be up to 12 characters long. Click the select ...

  • Page 277: Ospfv2 Neighbor Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 265 figure 6-72 ospfv2 lsdb table (show detail) window click the back button to return to the previous window. Ospfv2 neighbor table this window is used to display information on ospf neighbors. To view the following window, cli...

  • Page 278

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 266 enter a page number and click the go button to navigate to a specific page when multiple pages exist. After clicking the select vrf button, the following page will appear. Figure 6-74 ospfv2 neighbor table (select vrf) windo...

  • Page 279

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 267 figure 6-76 ospfv2 host route settings window the fields that can be configured in ospfv2 host route settings are described below: parameter description vrf name enter the name of the vrf instance here. This name can be up t...

  • Page 280: Ospfv3

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 268 ospfv3 ospfv3 process settings this window is used to display and configure ospfv3 process settings. To view the following window, click l3 features > ospf > ospfv3 > ospfv3 process settings, as shown below: figure 6-78 ospf...

  • Page 281

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 269 parameter description default metric enter the default metric value for the ospf process here. The range is from 1 to 16777214. By default, this value is 20. This value is used in conjunction with the ospfv3 redistribution f...

  • Page 282: Ospfv3 Area Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 270 to view the following window, click l3 features > ospf > ospfv3 > ospfv3 passive interface settings, as shown below: figure 6-81 ospfv3 passive interface settings window the fields that can be configured are described below:...

  • Page 283

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 271 parameter description feature is used only with abrs. It is used to consolidate or summarize routes for an area. The result is that a single summary route is advertised to other areas by the abr. Routing information is conde...

  • Page 284: Ospfv3 Interface Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 272 after clicking a normal area the process id link ( 1 ) in the table, the following page will appear. Figure 6-84 ospfv3 area settings (process id, normal) window click the ok button to close the window and return to the prev...

  • Page 285

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 273 parameter description instance id enter the instance identifier here. The range is from 0 to 255. If not specified, the default is 0. Area id enter the identifier of the area here. It can be specified as an ipv4 address. Int...

  • Page 286

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 274 parameter description hello interval, the earlier topological changes will be detected, but more routing traffic will ensue. This value must be the same for all routers and access servers on a specific network. The range is ...

  • Page 287

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 275 figure 6-87 ospfv3 redistribute settings window the fields that can be configured are described below: parameter description process id enter the id for an ipv6 ospf routing process here. It is locally assigned and should be...

  • Page 288

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 276 figure 6-88 ospfv3 virtual link settings window the fields that can be configured in ospfv3 virtual link are described below: parameter description process id enter the id for an ipv6 ospf routing process here. It is locally...

  • Page 289: Ospfv3 Lsdb Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 277 after clicking the process id link ( 1 ), the following page will appear. Figure 6-89 ospfv3 virtual link settings (process id) window click the ok button to close the window and return to the previous window. Ospfv3 lsdb ta...

  • Page 290: Ospfv3 Neighbor Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 278 parameter description • prefix - specifies to display information on the intra-area-prefix lsas. • link - specifies to display information about the link lsas. • inter-area prefix - specifies to display information only abou...

  • Page 291

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 279 figure 6-92 ospfv3 neighbor table window the fields that can be configured are described below: parameter description process id enter the ospfv3 process id to find here. The range is from 1 to 65535. Interface vlan enter th...

  • Page 292: Igmp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 280 figure 6-94 ospfv3 border router table window the fields that can be configured are described below: parameter description process id enter the ospfv3 process id to search for here. The range is from 1 to 65535. Click the fi...

  • Page 293

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 281 figure 6-96 igmp interface settings (edit) window the fields that can be configured are described below: parameter description version select the igmp version number here. The range is from 1 to 3. Select the default option ...

  • Page 294: Igmp Dynamic Group Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 282 igmp static group settings this window is used to display and configure the igmp static group settings. Use this window to create an igmp static group in the case that the attached host does not support the igmp protocol. On...

  • Page 295: Igmp Ssm Mapping Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 283 parameter description group enter the ip multicast group address here. Click the find button to locate a specific entry based on the information entered. Click the clear button to clear the entries based on the information s...

  • Page 296: Mld

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 284 parameter description acl name enter the standard ip access list name that contains the multicast groups to be mapped. To permit a group, specify ‘any’ in source address field and specify the group address in destination add...

  • Page 297

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 285 the fields that can be configured are described below: parameter description interface vlan enter the associated vlan id of the interface here. The range is from 1 to 4094. Click the find button to locate a specific entry ba...

  • Page 298: Mld Group Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 286 parameter description interface does not receive the report packet before the leave timer expires, then the interface’s membership will be removed from the group or channel that it is leaving. The value of the leave timer is...

  • Page 299

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 287 figure 6-104 mld ssm mapping settings window the fields that can be configured in mld ssm mapping settings are described below: parameter description ssm mapping state select to enable or disable the mld ssm mapping feature ...

  • Page 300: Igmp Proxy

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 288 select the acl and click the ok button to use the selected access list. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. Igmp proxy igmp proxy settings this window is used...

  • Page 301: Igmp Proxy Group Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 289 the fields that can be configured in igmp proxy downstream settings are described below: parameter description interface vlan enter the vlan interface id here. The range is from 1 to 4094. Downstream select to enable or disa...

  • Page 302: Mld Proxy

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 290 figure 6-108 igmp proxy forwarding table window the fields that can be configured are described below: parameter description group address enter the ipv4 group multicast address here. Click the find button to locate a specif...

  • Page 303: Mld Proxy Group Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 291 parameter description global state select to globally enable or disable the mld proxy feature here. Click the apply button to accept the changes made. The fields that can be configured in mld proxy upstream settings are desc...

  • Page 304: Dvmrp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 292 parameter description group address enter the ipv6 group multicast address here. Click the find button to locate a specific entry based on the information entered. Click the show all button to display all the entries. Mld pr...

  • Page 305: Dvmrp Routing Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 293 click the find button to locate a specific entry based on the information entered. Click the show all button to display all the entries. Click the edit button to modify the specified entry. Enter a page number and click the ...

  • Page 306: Dvmrp Neighbor Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 294 parameter description source network enter the source ipv4 network address and mask length here. Click the find button to locate a specific entry based on the information entered. Click the show all button to display all the...

  • Page 307

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 295 the third type of router created in the pim-sm configuration is the boot strap router (bsr). The goal of the boot strap router is to collect and relay rp information to pim-sm enabled routers on the lan. Although the rp can ...

  • Page 308: Pim For Ipv4

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 296 pim-dm the protocol independent multicast - dense mode (pim-dm) protocol should be used in networks with a low delay (low latency) and high bandwidth, as pim-dm is optimized to guarantee delivery of multicast packets and not...

  • Page 309

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 297 click the edit button to modify the specified entry. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. After clicking the edit button, the following page will appear. Figur...

  • Page 310

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 298 parameter description segment. The configured query interval is also used as the value for hold time. By configuring a smaller period for the interval, the unresponsive neighbor can be discovered faster and thus the failover...

  • Page 311

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 299 figure 6-118 pim bsr candidate window the fields that can be configured are described below: parameter description interface name enter the name of the interface here. Hash mask length enter the hash mask length for rp selec...

  • Page 312

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 300 figure 6-119 pim rp address window the fields that can be configured are described below: parameter description rp address enter the rp ipv4 address here. Group access list name enter the standard access list that will be us...

  • Page 313

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 301 click the apply button to use the selected access list. Pim rp candidate this window is used to display and configure the pim rp candidate settings. To view the following window, click l3 features > ip multicast routing prot...

  • Page 314

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 302 after clicking the show list button, the following page will appear. Figure 6-122 pim rp candidate (show list) window the fields that can be configured are described below: parameter description acl type select the acl type ...

  • Page 315

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 303 pim register settings this window is used to display and configure the pim register settings. To view the following window, click l3 features > ip multicast routing protocol > pim > pim for ipv4 > pim register settings, as s...

  • Page 316

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 304 the fields that can be configured in register keepalive time are described below: parameter description register keepalive enter the register keep-alive time value here. The range from 1 to 65525 seconds. Select the default ...

  • Page 317

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 305 the fields that can be configured are described below: parameter description spt threshold select the spt threshold option here. Options to choose from are 0 and infinity. • 0 - specifies to establish the source tree right a...

  • Page 318: Pim For Ipv6

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 306 the fields that can be configured are described below: parameter description acl type select the acl type that will be used to display the type of existing access lists in the table here. Options to choose from are ip acl, e...

  • Page 319

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 307 figure 6-130 pim for ipv6 interface window the fields that can be configured are described below: parameter description interface name enter the vlan interface name here. Click the find button to locate a specific entry base...

  • Page 320

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 308 parameter description mode select the ipv6 pim mode used in this interface here. Options to choose from are none and sparse mode. Pim for ipv6 will be disabled in this interface when the none option was selected. Designated ...

  • Page 321

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 309 figure 6-132 pim for ipv6 bsr candidate settings window the fields that can be configured are described below: parameter description interface name enter the vlan interface name used here. Hash mask length enter the hash mas...

  • Page 322

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 310 pim for ipv6 rp address this window is used to display and configure the ipv6 pim rp address settings. This feature only affects pim-sm operation. Use this feature to statically define the rp address for multicast groups tha...

  • Page 323

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 311 figure 6-135 pim for ipv6 rp address (show list) window the fields that can be configured are described below: parameter description acl type select the acl type that will be used to display the type of existing access lists...

  • Page 324

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 312 parameter description interface name enter the interface name here whose ipv6 address will be advertised as the candidate rp (c-rp). Group access list name enter the standard ipv6 access list that will be used here. Alternat...

  • Page 325

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 313 figure 6-138 pim for ipv6 rp candidate (edit) window the additional fields that can be configured are described below: parameter description interval enter the rp candidate advertisement interval value here. The range is fro...

  • Page 326

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 314 figure 6-140 pim for ipv6 rp table window the fields that can be configured are described below: parameter description group address/prefix length enter the multicast group ipv6 address and prefix length here. Source select ...

  • Page 327

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 315 parameter description register checksum methodology is pim rfc-compliant, excluding the data portion in the register message. Click the apply button to accept the changes made. The fields that can be configured in register p...

  • Page 328

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 316 pim for ipv6 ssm settings this window is used to display and configure the ipv6 pim ssm settings. To view the following window, click l3 features > ip multicast routing protocol > pim > pim for ipv6 > pim for ipv6 ssm settin...

  • Page 329

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 317 pim for ipv6 (s,g) keepalive time this window is used to display and configure the ipv6 pim (s,g) keep-alive time settings. This feature is used to configure the keep-alive timer, which is the period during which the pim rou...

  • Page 330

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 318 enter a page number and click the go button to navigate to a specific page when multiple pages exist. After clicking the show detail button, the following page will appear. Figure 6-147 pim for ipv6 mroute table (show detail...

  • Page 331: Msdp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 319 the fields that can be configured are described below: parameter description interface name enter the vlan interface name used in this display here. Click the find button to locate a specific entry based on the information e...

  • Page 332

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 320 parameter description option to use the default value which is 30 seconds. Sa cache expiry time enter the source-active (sa) cache expiry time value here. The range is from 65 to 65535 seconds. This is used to configure the ...

  • Page 333

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 321 click the show detail button to display more detailed information about the specified entry. Click the delete button to delete the specified entry. Enter a page number and click the go button to navigate to a specific page w...

  • Page 334

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 322 parameter description messages to a specified peer. By specifying this string, the router only forwards sa messages that match (s, g) pairs defined in the standard ip access list to a specified peer. Sa filter request select...

  • Page 335

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 323 msdp sa cache this window is used to view and clear the msdp sa cache table. To view the following window, click l3 features > ip multicast routing protocol > pim > msdp > msdp sa cache, as shown below: figure 6-154 msdp sa ...

  • Page 336: Ipmc

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 324 click the apply button to accept the changes made. Click the find button to find and display an entry based on the information entered. Msdp mesh group settings this window is used to display and configure the msdp mesh grou...

  • Page 337

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 325 figure 6-157 ip multicast global settings window the fields that can be configured in ip multicast routing global state are described below: parameter description global state select to globally enable or disable the ip mult...

  • Page 338

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 326 after clicking the please select button, the following page will appear. Figure 6-158 ip multicast global settings (please select) window select the acl and click the ok button to use the selected access list. Enter a page n...

  • Page 339: Ip Multicast Rpf Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 327 parameter description static selecting this option specifies to display the multicast static routes. Multicast protocol select this option and then select the multicast protocol that will be used in this display here. Option...

  • Page 340

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 328 the fields that can be configured are described below: parameter description group address enter the multicast group ip address here. Source address enter the multicast source ip address here. Click the find button to locate...

  • Page 341

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 329 control packet cpu filtering this window is used to display and configure the ipmc control packet cpu filtering settings. To view the following window, click l3 features > ip multicast routing protocol > ipmc > control packe...

  • Page 342: Ipv6Mc

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 330 ipv6mc ipv6 multicast global settings this window is used to display and configure the global ipv6 multicast settings. To view the following window, click l3 features > ip multicast routing protocol > ipv6mc > ipv6 multicast...

  • Page 343

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 331 figure 6-165 ipv6 static multicast route settings window the fields that can be configured are described below: parameter description ipv6 address/prefix length enter the ipv6 network address and prefix length of the multica...

  • Page 344: Ipv6 Rpf Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 332 parameter description multicast routing table. Click the find button to locate a specific entry based on the information entered. Click the show all button to display all the entries. Ipv6 multicast routing forwarding cache ...

  • Page 345: Bgp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 333 bgp bgp global settings this window is used to display and configure the global border gateway protocol (bgp) settings. To view the following window, click l3 features > bgp > bgp global settings, as shown below: figure 6-16...

  • Page 346

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 334 parameter description 65535 seconds. Hold time enter the hold time value here. This specifies the length of time to timeout the keep-alive message. The software will declare a bgp peer dead after the on timeout. The range is...

  • Page 347

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 335 the fields that can be configured in bgp trap settings are described below: parameter description peer established trap state select to enable or disable the bgp peer established trap state here. Peer backward-trans trap sta...

  • Page 348: Bgp Network Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 336 enter a page number and click the go button to navigate to a specific page when multiple pages exist. After clicking the please select button, the following page will appear. Figure 6-171 bgp aggregate address settings (plea...

  • Page 349

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 337 click the edit button to re-configure the specific entry. Click the delete button to remove the specific entry. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. After clic...

  • Page 350

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 338 parameter description source protocol select the source protocol here. Options to choose from are: • connected - specifies to redistribute connected routes to bgp. • static - specifies to redistribute static routes to bgp. •...

  • Page 351: Bgp Dampening Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 339 bgp route preference settings this window is used to display and configure the bgp route preference settings. To view the following window, click l3 features > bgp > bgp route preference settings, as shown below: figure 6-17...

  • Page 352

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 340 to view the following window, click l3 features > bgp > bgp dampening settings, as shown below: figure 6-178 bgp dampening settings window the fields that can be configured in bgp dampening are described below: parameter des...

  • Page 353

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 341 parameter description minutes. Reuse value enter the re-use value here. As the penalty is decreased and falls below the re- use threshold, the route will be re-entered into the routing table as a normal route. The range is f...

  • Page 354

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 342 parameter description configuration. • ipv4 vrf - specifies to use a vrf instance in this configuration. Enter the name of the vrf instance in the space provided or click the please select button to select a pre-configured v...

  • Page 355

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 343 figure 6-182 bgp dampening flap statistics table window the fields that can be configured are described below: parameter description address family select the address family that will be used here. Options to choose from are...

  • Page 356: Bgp Reflector Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 344 select the vrf entry and click the ok button to use the selected vrf entry. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. Bgp reflector settings this window is used to ...

  • Page 357: Bgp Confederation Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 345 parameter description here. State select to enable or disable the bgp reflector client state here. Click the apply button to accept the changes made. Bgp confederation settings this window is used to display and configure th...

  • Page 358

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 346 figure 6-186 bgp as path access list settings window the fields that can be configured are described below: parameter description list name enter the name of the as path access list here. This name can be up to 16 characters...

  • Page 359

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 347 figure 6-187 bgp community list settings window the fields that can be configured are described below: parameter description list name enter the name of the community list here. This name can be up to 16 characters long. Typ...

  • Page 360

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 348 click the find button to locate a specific entry based on the information entered. Click the show all button to display all the available entries. Click the delete button to remove the specific entry. Enter a page number and...

  • Page 361: Bgp Clear Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 349 parameter description regular expression enter the regular expression here. This string can be up to 80 characters long. Click the apply button to accept the changes made. Bgp clear settings this window is used to display an...

  • Page 362: Bgp Summary Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 350 parameter description peer group enter the name of the peer group of which the bgp peer session will be cleared here. This name can be up to 16 characters long. Neighbor address enter the ipv4 address or the ipv6 address of ...

  • Page 363: Bgp Routing Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 351 parameter description layer 2 vpn vpls address family. Click the find button to locate a specific entry based on the information selected/entered. After clicking the please select button, the following page will appear. Figu...

  • Page 364

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 352 parameter description • vpnv4 vrf - specifies to display bgp routing information related to the vrf instance in the vpnv4 address family. Enter the name of the vrf instance here. This name can be up to 12 characters long. Al...

  • Page 365: Bgp Labels Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 353 parameter description ○ community list - enter the name of the bgp community list here. This name can be up to 16 characters long. ○ exact match - select this option to display only routes that are an exact match. ○ l2vpn pr...

  • Page 366: Bgp Neighbor

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 354 the fields that can be configured are described below: parameter description address family select the address family that will be used here. Options to choose from are: • vpnv4 all - specifies to display all bgp label infor...

  • Page 367

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 355 figure 6-196 neighbor window the fields that can be configured in neighbor settings are described below: parameter description ip address select and enter the ipv4 or ipv6 address of the neighboring router here. Vrf name ent...

  • Page 368: Peer Group

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 356 parameter description neighbor address select and enter the ipv4 or ipv6 address of the neighboring router here. Type select the type of information to display here. Options to choose from are: • none - specifies to display ...

  • Page 369

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 357 figure 6-198 peer group window the fields that can be configured in peer group are described below: parameter description group name enter the name of the bgp peer group here. This name can be up to 16 characters long. Vrf n...

  • Page 370

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 358 parameter description address family select the address family that will be used here. Options to choose from are: • ipv4 unicast - specifies to display the bgp peer group table related to the ipv4 unicast address family. • ...

  • Page 371: Neighbor Activate

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 359 neighbor activate this window is used to view, activate and deactivate bgp neighbors. To view the following window, click l3 features > bgp > bgp neighbor > neighbor activate, as shown below: figure 6-201 neighbor activate w...

  • Page 372: Neighbor Shutdown

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 360 select the vrf entry and click the ok button to use the selected vrf entry. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. Neighbor shutdown this window is used to shut ...

  • Page 373

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 361 to view the following window, click l3 features > bgp > bgp neighbor > neighbor map settings, as shown below: figure 6-205 neighbor map settings window the fields that can be configured are described below: parameter descrip...

  • Page 374: Neighbor Filter Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 362 parameter description long. Click the apply button to accept the changes made. After clicking the please select button, the following page will appear. Figure 6-206 neighbor map settings (please select) window select the vrf...

  • Page 375

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 363 parameter description • ipv4 multicast - specifies to configure the bgp neighbor filter settings related to the ipv4 multicast address family. • l2vpn vpls - specifies to configure the bgp neighbor filter settings related to...

  • Page 376

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 364 neighbor maximum prefix settings this window is used to display and configure the bgp neighbor maximum prefix settings. This is used to control the maximum number of prefixes that can be accepted from a bgp neighbor. To view...

  • Page 377: Neighbor General Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 365 parameter description threshold was exceeded. Click the apply button to accept the changes made. After clicking the please select button, the following page will appear. Figure 6-210 neighbor maximum prefix settings (please ...

  • Page 378

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 366 the fields that can be configured are described below: parameter description address family select the address family that will be used here. Options to choose from are: • ipv4 unicast - specifies to configure the bgp genera...

  • Page 379

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 367 parameter description capability graceful restart select to enable or disable the graceful restart capability here. This is used to enable the feature to advertise the graceful restart capability to its neighbors. Descriptio...

  • Page 380: Bfd

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 368 bfd bfd settings this window is used to display and configure the bidirectional forwarding detection (bfd) settings. To view the following window, click l3 features > bfd > bfd settings, as shown below: figure 6-213 bfd sett...

  • Page 381: Isis

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 369 note: performance will vary depending on the configuration and traffic patterns. It is advised to perform lab testing before deploying bfd in a live environment. To view the following window, click l3 features > bfd > bfd ne...

  • Page 382

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 370 the fields that can be configured are described below: parameter description area tag enter the isis area tag here. This can be up to 16 characters long. Click the apply button to accept the changes made. Click the find butt...

  • Page 383

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 371 parameter description select the authenticate snp option to insert the password into sequence number pdus (snps). • validate - specifies to insert the password into the snps and check the password in snps on receiving. • sen...

  • Page 384

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 372 parameter description lsps from timing out. Reducing the refresh interval reduces the amount of time undetected link-state database corruption can persist at the cost of increased link utilization. Increasing the interval re...

  • Page 385

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 373 parameter description spf interval level-2 enter the spf interval level-2 value here. This is used to customize isis throttling of spf calculations applied to level-2 areas only. The range is from 1 to 120 seconds. Select th...

  • Page 386: Isis Router Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 374 isis router settings this window is used to display and configure the isis router settings. To view the following window, click l3 features > isis > isis router settings, as shown below: figure 6-220 isis router settings (ip...

  • Page 387

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 375 parameter description distance enter the distance value here. This is used to define the administrative distance of isis routes. The range is from 1 to 255 for ipv4 isis routes and 1 to 254 for ipv6 isis routes. Click the ap...

  • Page 388: Isis Interface Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 376 after clicking the summary prefix list button, the following page will appear. Figure 6-223 isis router settings (summary prefix list) window the fields that can be configured are described below: parameter description summa...

  • Page 389

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 377 parameter description interface vlan enter the vlan id that will be used here. The range is from 1 to 4094. Ipv4 select this option to enable the isis routing protocol for ipv4 on the interface. Ipv6 select this option to en...

  • Page 390

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 378 parameter description mesh group enter the mesh group number here. This is used to optimize link-state packet (lsp) flooding on point-to-point networks. Select the block option to specify that no lsp flooding will take place...

  • Page 391: Isis Redistribute Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 379 parameter description 0 to 127. Select the default option to use the default value. Wide metric level-1 enter the wider metric value that is assigned to the link and used to calculate the cost from other routers via the link...

  • Page 392

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 380 parameter description metric type select the metric type of the redistributed routes here. Options to choose from are: • none - the metric type is not specified. • internal - the redistributed routes advertised with internal...

  • Page 393: Isis Route Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 381 click the apply button to accept the changes made. Click the find button to locate a specific entry based on the information entered. Click the delete button to remove the specific entry. Enter a page number and click the go...

  • Page 394: Isis Topology

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 382 the fields that can be configured are described below: parameter description area tag enter the isis area tag that will be used in this display here. This can be up to 16 characters long. Level select the routing level that ...

  • Page 395: Isis Hostname

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 383 parameter description • ipv4 - specifies to display the isis ipv4 routing table information. • ipv6 - specifies to display the isis ipv6 routing table information. Area tag enter the isis area tag that will be used in this d...

  • Page 396: Ip Route Filter

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 384 figure 6-234 isis neighbors (show detail) window click the back button to return to the previous window. Ip route filter ip prefix list this window is used to display and configure the ip route filter prefix list settings. T...

  • Page 397: Route Map

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 385 parameter description ipv6 network address enter the ipv6 address and prefix length here. Ge enter the minimum prefix length of the route that can be matched here. The range is from 1 to 32 for ipv4 and 1 to 128 for ipv6. Le...

  • Page 398

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 386 click the delete button to delete the specified entry. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. After clicking the edit button in the match clauses column, the fol...

  • Page 399

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 387 parameter description ipv6 next hop acl select and enter the standard ipv6 access list name here. This option is used to define a clause to match the route’s next hop based on the standard ipv6 access list. This string can b...

  • Page 400

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 388 figure 6-238 route map (set clauses, edit) window the fields that can be configured are described below: parameter description action select add to add a new entry based in the information entered. Select delete to delete an...

  • Page 401

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 389 parameter description • community string - select and enter the community string here. It can be a user-specified number represented by aa:nn, where aa (as number) is the upper part of the word and nn (community number, user...

  • Page 402: Policy Route

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 390 click the apply button to accept the changes made. Click the back button to return to the previous window. Policy route this window is used to display and configure the policy route settings. To view the following window, cl...

  • Page 403

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 391 figure 6-241 vrrp settings window the fields that can be configured in vrrp settings are described below: parameter description snmp server traps vrrp new master select to enable or disable the snmp server traps feature for ...

  • Page 404: Vrrpv3 Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 392 enter a page number and click the go button to navigate to a specific page when multiple pages exist. After clicking the edit button, the following page will appear. Figure 6-242 vrrp settings (edit) window the fields that c...

  • Page 405

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 393 figure 6-243 vrrpv3 settings window the fields that can be configured are described below: parameter description vlan enter the id of the vlan interface that will be used here. The range is from 1 to 4094. Vrid enter the vir...

  • Page 406

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 394 parameter description virtual ip address enter the virtual ipv4/ipv6 address here. This parameter will be either ipv4 or ipv6 depending on the address family selection made in the previous step. All routers in the same vrrp ...

  • Page 407: Basic Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 395 7. Quality of service (qos) basic settings advanced settings qos pfc wred iscsi basic settings port default cos this window is used to display and configure the port default cos settings. To view the following window, click ...

  • Page 408

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 396 figure 7-2 port scheduler method window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the r...

  • Page 409: Queue Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 397 queue settings this window is used to display and configure the queue settings. To view the following window, click qos > basic settings > queue settings, as shown below: figure 7-3 queue settings window the fields that can ...

  • Page 410: Port Rate Limiting

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 398 figure 7-4 cos to queue mapping window the fields that can be configured are described below: parameter description queue id select the queue id that will be mapped to the corresponding cos value. Options to choose from are ...

  • Page 411: Queue Rate Limiting

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 399 parameter description the space provided. This value must be between 8 and 10000000 kbps. Also, enter the burst size value in the space provided. This value must be between 0 and 128000 kilobytes. • when percent is selected,...

  • Page 412: Advanced Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 400 parameter description even if the bandwidth is available. When configuring the minimal bandwidth, the aggregate of the configured minimum bandwidth must be less than 75 percent of the interface bandwidth to make sure the con...

  • Page 413: Dscp Cos Mapping

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 401 click the apply button to accept the changes made. Click the delete button to remove the specific entry. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. Port trust state ...

  • Page 414: Cos Color Mapping

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 402 figure 7-9 dscp cos mapping window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the range ...

  • Page 415: Dscp Color Mapping

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 403 figure 7-10 cos color mapping window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the rang...

  • Page 416: Class Map

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 404 figure 7-11 dscp color mapping window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the ran...

  • Page 417: Aggregate Policer

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 405 click the apply button to accept the changes made. Click the match button to configure the specific entry. Click the delete button to remove the specific entry. Enter a page number and click the go button to navigate to a sp...

  • Page 418

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 406 to view the following window, click qos > advanced settings > aggregate policer, as shown below: figure 7-14 aggregate policer (single rate setting) window the fields that can be configured are described below: parameter des...

  • Page 419

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 407 parameter description • when selecting the set-dscp-1p option, enter the ip dscp and 1p transmit values in the spaces provided. Violate action select the violate action here. The violate action specifies the action to take o...

  • Page 420

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 408 parameter description bucket for the two-rate metering. Confirm burst enter the confirm burst value here. This value must be between 0 and 16384 kbytes. The confirm burst value specifies the burst size for the first token bu...

  • Page 421: Policy Map

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 409 parameter description • when selecting the transmit option, packets will be transmitted unaltered. • when selecting the set-dscp-1p option, enter the ip dscp and 1p transmit values in the spaces provided. Color aware select ...

  • Page 422

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 410 click the set action button to configure the set action settings for the specified entry. Click the policer button to configure the policer settings for the specified entry. Enter a page number and click the go button to nav...

  • Page 423

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 411 figure 7-18 policy map (policer) window the fields that can be configured are described below: parameter description none select this option to specify that no policer settings will be configured for this entry. Specify sele...

  • Page 424: Policy Binding

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 412 parameter description • transmit - specifies that the exceed action is to transmit the packet unmodified. • set-dscp-1p - specifies that the exceed action is to modify the dscp and 802.1p values and then to transmit the pack...

  • Page 425: Qos Pfc

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 413 parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the range of ports that will be used for this configuration here. Direction select the direction opt...

  • Page 426: Network Qos Policy Map

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 414 parameter description match cos select the ieee 802.1q class of service (cos) value to be matched here. The range is from 0 to 7. When a packet is received, the packet will be given an internal cos. This internal cos is used...

  • Page 427: Network Qos Policy Binding

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 415 after clicking the edit button, the following page will appear. Figure 7-23 network qos policy map (edit) window the fields that can be configured are described below: parameter description pause select to enable or disable ...

  • Page 428: Pfc Port Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 416 parameter description unit select the switch unit id that will be used here. From port - to port select the switch port range that will be used here. Direction select the input direction here. This specifies to apply the pol...

  • Page 429: Wred

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 417 parameter description unit select the switch unit id that will be used here. From port - to port select the switch port range that will be used here. Select the all option to specify that all ports will be used here. Frame t...

  • Page 430

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 418 figure 7-26 wred profile window the fields that can be configured are described below: parameter description profile enter the wred profile id here. The range is from 1 to 128. Packet type select the packet type here. Option...

  • Page 431: Wred Queue

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 419 wred queue this window is used to display and configure the wred queue settings. Wred drops packets, based on the average queue size exceeding a specific threshold, to indicate congestion. Explicit congestion notification (e...

  • Page 432: Iscsi

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 420 figure 7-28 wred drop counter window the fields that can be configured are described below: parameter description unit select the switch unit id that will be used here. From port - to port select the switch port range that w...

  • Page 433

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 421 figure 7-29 iscsi settings window the fields that can be configured are described below: parameter description iscsi state select to globally enable or disable the iscsi awareness feature here. Iscsi cos select the iscsi cos...

  • Page 434: Iscsi Sessions

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 422 iscsi sessions this window is used to view the iscsi active session table. To view the following window, click qos > iscsi > iscsi sessions, as shown below: figure 7-30 iscsi sessions window.

  • Page 435: Acl Configuration Wizard

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 423 8. Access control list (acl) acl configuration wizard acl access list acl interface access group acl vlan access map acl vlan filter cpu acl acl configuration wizard this window is used to guide the user to create a new acl ...

  • Page 436: Step 3 - Add Rule

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 424 parameter description create select this option to create a new acl access list using the configuration wizard. Acl name enter the new acl name here. This name can be up to 32 characters long. Update select this option to up...

  • Page 437

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 425 figure 8-4 acl configuration wizard (create, packet type, mac) window the fields that can be configured are described below: parameter description sequence no. Enter the acl rule number here. This value must be between 1 and...

  • Page 438

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 426 parameter description ethernet type enter the ethernet type hexadecimal value here. This value must be between 0x600 and 0xffff. When any ethernet type profile is selected in the specify ethernet type drop-down list, the app...

  • Page 439: Ipv4

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 427 ipv4 after clicking the ipv4 radio button and the next button, the following window will appear. Figure 8-5 acl configuration wizard (create, packet type, ipv4) window the fields that can be configured are described below: p...

  • Page 440

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 428 parameter description source select and enter the source information here. Options to choose from are any, host, and ip. • when the any option is selected, any source traffic will be evaluated according to the conditions of ...

  • Page 441

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 429 parameter description mask will be used. Enter the destination port mask value in the space provided. The range is from 0x0 to 0xffff. This parameter is only available in the protocol type tcp and udp. Specify icmp message t...

  • Page 442: Ipv6

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 430 ipv6 after clicking the ipv6 radio button and the next button, the following window will appear. Figure 8-6 acl configuration wizard (create, packet type, ipv6) window the fields that can be configured are described below: p...

  • Page 443

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 431 parameter description source select and enter the source information here. Options to choose from are any, host, and ipv6. • when the any option is selected, any source traffic will be evaluated according to the conditions o...

  • Page 444: Step 4 - Apply Port

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 432 parameter description this parameter is only available in the protocol type tcp and udp. Specify icmp message type select the icmp message type used here. This parameter is only available in the protocol type icmp. Icmp mess...

  • Page 445: Acl Access List

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 433 parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the appropriate port range used for the configuration here. Direction select the direction here. Opt...

  • Page 446

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 434 click the delete button, next to the acl rule, to remove the specific acl rule. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. After clicking the edit button, the follow...

  • Page 447: Standard Ip Acl

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 435 parameter description standard ip acl, extended ip acl, standard ipv6 acl, extended ipv6 acl, extended mac acl, and extended expert acl. Id enter the id for the acl here. • for a standard ip acl, the range from 1 to 1999. • ...

  • Page 448: Extended Ip Acl

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 436 parameter description bit value 0 will be checked. Destination select and enter the destination information here. Options to choose from are any, host, ip, and wildcard. • when the any option is selected, any destination tra...

  • Page 449

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 437 parameter description this value is not specified, the system will automatically generate an acl rule number for this entry. Action select the action that this rule will take here. Options to choose from are permit, deny, an...

  • Page 450

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 438 parameter description • when selecting the = option, the specific selected port number will be used. • when selecting the > option, all ports greater than the selected port, will be used. • when selecting the option, all por...

  • Page 451: Standard Ipv6 Acl

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 439 click the apply button to accept the changes made. Click the back button to discard the changes made and return to the previous page. Standard ipv6 acl after selecting a standard ipv6 acl and clicking the add rule button, th...

  • Page 452: Extended Ipv6 Acl

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 440 click the back button to discard the changes made and return to the previous page. Extended ipv6 acl after selecting an extended ipv6 acl and clicking the add rule button, the following page will appear. Figure 8-14 extended...

  • Page 453

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 441 parameter description • when the host option is selected, enter the source host ipv6 address here. • when the ipv6 option is selected, the prefix length option will also be available. Enter the source ipv6 address and prefix...

  • Page 454: Extended Mac Acl

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 442 parameter description specify icmp message type select the icmp message type used here. This parameter is only available in the protocol type icmp. Icmp message type when the icmp message type is not selected, enter the icmp...

  • Page 455

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 443 figure 8-15 extended mac acl (add rule) window the fields that can be configured are described below: parameter description sequence no. Enter the sequence number of this acl rule here. The range is from 1 to 65535. If this ...

  • Page 456: Extended Expert Acl

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 444 parameter description appropriate hexadecimal value will automatically be entered. Ethernet type mask enter the ethernet type mask hexadecimal value here. This value must be between 0x0 and 0xffff. When the ethernet type pro...

  • Page 457

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 445 figure 8-16 extended expert acl (add rule) window the fields that can be configured are described below: parameter description sequence no. Enter the sequence number of this acl rule here. The range is from 1 to 65535. If th...

  • Page 458

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 446 parameter description corresponding to the bit value 1 will be ignored. The bit corresponding to the bit value 0 will be checked. Destination select and enter the destination ip information here. Options to choose from are a...

  • Page 459

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 447 parameter description used. • when selecting the option, all ports smaller than the selected port, will be used. • when selecting the ≠ option, all ports, excluding the selected port, will be used. • when selecting the range...

  • Page 460: Acl Interface Access Group

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 448 parameter description is from 1 to 4094. • mask - enter the inner vlan id mask value here. The range is from 0x0 to 0xfff. Vlan range select and enter the vlan range that will be associated with this acl rule here. Enter the...

  • Page 461: Acl Vlan Access Map

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 449 click the apply button to accept the changes made. After clicking the please select button, the following window will appear: figure 8-18 acl interface access group (please select) window select the radio button next to the ...

  • Page 462

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 450 click the clear counter button to the clear the counter information for the specified access map. Click the find button to locate a specific entry based on the information entered. Click the binding button to match an access...

  • Page 463: Acl Vlan Filter

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 451 acl vlan filter this window is used to display and configure the acl vlan filter settings. To view the following window, click acl > acl vlan filter, as shown below: figure 8-22 acl vlan filter window the fields that can be ...

  • Page 464

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 452 click the find button to locate a specific entry based on the information entered. Click the binding button to configure the binding settings for the specified entry. Click the delete button to delete the specified entry. En...

  • Page 465

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 453 the fields that can be configured in match mac access list are described below: parameter description sequence no. Enter the sequence number of the associated match entry here. The range is from 1 to 65535. The lower the num...

  • Page 466: 9.  Security

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 454 9. Security port security 802.1x aaa radius tacacs impb dhcp server screening arp spoofing prevention bpdu attack protection netbios filtering mac authentication web-based access control network access authentication safegua...

  • Page 467

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 455 parameter description trap state select to enable or disable port security traps on the switch. Click the apply button to accept the changes made. The fields that can be configured in port security trap rate settings are des...

  • Page 468

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 456 figure 9-2 port security port settings window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select...

  • Page 469: 802.1X

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 457 parameter description specified time period. Click the apply button to accept the changes made. Port security address entries this window is used to view, clear and configure the port security address entries. To view the fo...

  • Page 470

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 458 figure 9-4 the eapol packet utilizing this method, unauthorized devices are restricted from connecting to a lan through a port to which the user is connected. Eapol packets are the only traffic that can be transmitted throug...

  • Page 471

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 459 figure 9-6 the authentication server authenticator the authenticator (the switch) is an intermediary between the authentication server and the client. The authenticator serves two purposes when utilizing the 802.1x function....

  • Page 472

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 460 figure 9-8 the client authentication process utilizing the three roles stated above, the 802.1x protocol provides a stable and secure way of authorizing and authenticating users attempting to access the network. Only eapol t...

  • Page 473

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 461 the original intent behind the development of 802.1x was to leverage the characteristics of point-to-point in lans. As any single lan segment in such infrastructures has no more than two devices attached to it, one of which ...

  • Page 474: 802.1X Global Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 462 figure 9-11 example of typical host-based configuration 802.1x global settings this window is used to display and configure the global 802.1x settings. To view the following window, click security > 802.1x > 802.1x global se...

  • Page 475

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 463 figure 9-13 802.1x port settings window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the a...

  • Page 476: Authenticator Statistics

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 464 figure 9-14 authentication sessions information window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to po...

  • Page 477: Authenticator Diagnostics

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 465 authenticator session statistics this window is used to view and clear the authenticator session statistics. To view the following window, click security > 802.1x > authenticator session statistics, as shown below: figure 9-...

  • Page 478: Aaa

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 466 figure 9-17 authenticator diagnostics window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this query here. Port select the appropriate port us...

  • Page 479

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 467 parameter description aaa state select to enable or disable the global authentication, authorization, and accounting (aaa) state. Click the apply button to accept the changes made. Application authentication settings this wi...

  • Page 480

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 468 figure 9-21 application accounting settings window click the edit button to re-configure the specific entry. Figure 9-22 application accounting settings (edit) window the fields that can be configured in application accounti...

  • Page 481: Authentication Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 469 enter a page number and click the go button to navigate to a specific page when multiple pages exist. Authentication settings this window is used to display and configure the aaa network and exec authentication settings. To ...

  • Page 482

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 470 parameter description • local - specifies to use the local database for authentication. • group - specifies to use the server groups defined by the aaa group server. Enter the aaa group server name in the space provided. Thi...

  • Page 483: Accounting Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 471 the fields that can be configured in aaa authentication enable are described below: parameter description status select to enable or disable the aaa authentication enable state here. Method 1 ~ method 4 select the method lis...

  • Page 484

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 472 figure 9-25 accounting settings window the fields that can be configured in aaa accounting network are described below: parameter description default select to enable or disable the use of the default method list here. Metho...

  • Page 485: Radius

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 473 parameter description list name enter the method list name that will be used with the aaa accounting exec option here. Method 1 ~ method 4 select the method lists that will be used for this configuration here. Options to cho...

  • Page 486

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 474 figure 9-29 radius global settings window the fields that can be configured in radius global settings are described below: parameter description deadtime enter the dead time value here. This value must be between 1 and 1440 ...

  • Page 487: Radius Server Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 475 radius server settings this window is used to display and configure the radius server settings. To view the following window, click security > radius > radius server settings, as shown below: figure 9-30 radius server settin...

  • Page 488

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 476 figure 9-31 radius group server settings window the fields that can be configured are described below: parameter description group server name enter the radius group server name here. This name can be up to 32 characters lon...

  • Page 489: Radius Statistic

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 477 click the back button to return to the previous window. Radius statistic this window is used to view and clear the radius statistics information. To view the following window, click security > radius > radius statistic, as s...

  • Page 490: Tacacs Server Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 478 figure 9-34 tacacs global settings window the fields that can be configured in tacacs global ipv4 source interface are described below: parameter description ipv4 tacacs source interface name enter the name of the ipv4 tacac...

  • Page 491

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 479 parameter description key enter the key, used to communicate with the tacacs+ server, here. This key can be up to 254 characters long. Click the apply button to accept the changes made. Click the delete button to remove the ...

  • Page 492: Tacacs Statistic

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 480 the fields that can be configured are described below: parameter description vrf name enter the name of the vrf instance here. This name can be up to 12 characters long. Ipv4 tacacs source interface name enter the name of th...

  • Page 493: Ipv4

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 481 ipv4 dhcpv4 snooping dhcp snooping global settings this window is used to display and configure the global dhcp snooping settings. To view the following window, click security > impb > ipv4 > dhcpv4 snooping > dhcp snooping ...

  • Page 494

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 482 figure 9-40 dhcp snooping port settings window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port selec...

  • Page 495

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 483 parameter description state select to enable or disable the dhcp snooping vlan setting here. Click the apply button to accept the changes made. Dhcp snooping database this window is used to display and configure the dhcp sno...

  • Page 496: Dynamic Arp Inspection

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 484 parameter description url select the location from the drop-down list and enter the url where the dhcp snooping database will be loaded from here. Locations to choose from are tftp, ftp, and flash. An example url is given. C...

  • Page 497

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 485 to view the following window, click security > impb > ipv4 > dynamic arp inspection > arp access list, as shown below: figure 9-44 arp access list window the fields that can be configured are described below: parameter descr...

  • Page 498

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 486 click the back button to return to the previous page. Click the apply button to accept the changes made. Click the delete button to remove the specified entry. Arp inspection settings this window is used to display and confi...

  • Page 499

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 487 parameter description arp access list name enter the arp access list name used here. This name can be up to 32 characters long. Vid list enter the vlan id list used here. Static acl select whether to use a static acl or not ...

  • Page 500

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 488 to view the following window, click security > impb > ipv4 > dynamic arp inspection > arp inspection vlan, as shown below: figure 9-48 arp inspection vlan window the fields that can be configured are described below: paramet...

  • Page 501: Ip Source Guard

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 489 figure 9-50 arp inspection log window the fields that can be configured are described below: parameter description log buffer enter the log buffer value used here. This value must be between 1 and 1024. By default, this valu...

  • Page 502

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 490 to view the following window, click security > impb > ipv4 > ip source guard > ip source guard binding, as shown below: figure 9-52 ip source guard binding window the fields that can be configured in ip source binding settin...

  • Page 503: Advanced Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 491 enter a page number and click the go button to navigate to a specific page when multiple pages exist. Ip source guard hw entry this window is used to view the ip source guard hardware entries. To view the following window, c...

  • Page 504

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 492 the fields that can be configured in ip-mac-port binding trap settings are described below: parameter description trap state select the enable or disable the ip-mac-port binding option’s trap state. Click the apply button to...

  • Page 505: Ipv6

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 493 ipv6 ipv6 snooping this window is used to display and configure the ipv6 snooping settings. To view the following window, click security > impb > ipv6 > ipv6 snooping, as shown below: figure 9-56 ipv6 snooping window the fie...

  • Page 506: Ipv6 Nd Inspection

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 494 parameter description dhcp-pd snooping performs dhcpv6 snooping of prefix delegation (pd) to setup bindings between the delegating router (assigned with an ipv6 prefix) and the corresponding requesting router. The bindings c...

  • Page 507: Ipv6 Ra Guard

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 495 ipv6 ra guard this window is used to display and configure the ipv6 router advertisement (ra) guard settings. To view the following window, click security > impb > ipv6 > ipv6 ra guard, as shown below: figure 9-58 ipv6 ra gu...

  • Page 508: Ipv6 Dhcp Guard

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 496 ipv6 dhcp guard this window is used to display and configure the ipv6 dhcp guard settings. To view the following window, click security > impb > ipv6 > ipv6 dhcp guard, as shown below: figure 9-60 ipv6 dhcp guard window the ...

  • Page 509: Ipv6 Source Guard

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 497 ipv6 source guard ipv6 source guard settings this window is used to display and configure the ipv6 source guard settings. To view the following window, click security > impb > ipv6 > ipv6 source guard > ipv6 source guard set...

  • Page 510: Dhcp Server Screening

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 498 figure 9-63 ipv6 neighbor binding window the fields that can be configured in ipv6 neighbor binding settings are described below: parameter description mac address enter the mac address used here. Vid enter the vlan id used ...

  • Page 511

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 499 when the dhcp server screening function is enabled on a port, all dhcp server packets received on this ports will be redirected to the cpu for a software-based check. Legal dhcp server packets will be forwarded out and illeg...

  • Page 512: Arp Spoofing Prevention

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 500 click the apply button to accept the changes made. Click the clear log button to clear the log. Dhcp server screening port settings this window is used to display and configure the dhcp server screening port settings. To vie...

  • Page 513: Bpdu Attack Protection

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 501 figure 9-66 arp spoofing prevention window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select th...

  • Page 514: Netbios Filtering

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 502 figure 9-67 bpdu attack protection window the fields that can be configured in bpdu attack protection global settings are described below: parameter description bpdu attack protection state select to enable or disable the gl...

  • Page 515: Mac Authentication

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 503 figure 9-68 netbios filtering window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the rang...

  • Page 516

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 504 figure 9-69 mac authentication window the fields that can be configured in mac authentication global settings are described below: parameter description mac authentication state select to enable or disable the global mac aut...

  • Page 517: Web-Based Access Control

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 505 web-based access control web-based access control (wac) is a feature designed to authenticate a user when the user is trying to access the internet via the switch. The authentication process uses the http or https protocol. ...

  • Page 518

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 506 figure 9-70 radius authentication server conditions and limitations • if the client is utilizing dhcp to attain an ip address, the authenticating vlan must provide a dhcp server or a dhcp relay function so that client may ob...

  • Page 519: Web Authentication

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 507 web authentication this window is used to display and configure the web authentication settings. To view the following window, click security > web-based access control > web authentication, as shown below: figure 9-71 web a...

  • Page 520: Wac Customize Page

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 508 figure 9-72 wac port settings window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the appr...

  • Page 521: Guest Vlan

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 509 the fields that can be configured are described below: parameter description page title enter a custom page title message here. This message can be up to 128 characters long. Login window title enter a custom login window ti...

  • Page 522

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 510 to view the following window, click security > network access authentication > network access authentication global settings, as shown below: figure 9-75 network access authentication global settings window the fields that c...

  • Page 523

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 511 parameter description authorization state select to enable or disable the authorized state here. The option is used to enable or disable the acceptance of an authorized configuration. When authorization is enabled for authen...

  • Page 524

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 512 parameter description from port - to port select the appropriate port range used for the configuration here. Host mode select the host mode option that will be associated with the selected port(s) here. Options to choose fro...

  • Page 525: Safeguard Engine

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 513 figure 9-77 network access authentication sessions information window the fields that can be configured are described below: parameter description port select the appropriate switch unit and port used for the query here. Mac...

  • Page 526: Safeguard Engine Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 514 protocol name sub-interface (group) description 802.1x protocol port-based network access control arp protocol address resolution protocol bgp protocol border gateway protocol dhcp protocol dynamic host configuration protoco...

  • Page 527: Cpu Protect Counters

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 515 figure 9-78 safeguard engine settings window the fields that can be configured in safeguard engine settings are described below: parameter description safeguard engine state select to enable or disable the safeguard engine f...

  • Page 528: Cpu Protect Sub-Interface

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 516 click the clear button to clear the information based on the selections made. Click the clear all button to clear all the information in this table. Cpu protect sub-interface this window is used to display and configure the ...

  • Page 529: Trusted Host

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 517 figure 9-81 cpu protect type window the fields that can be configured in cpu protect type are described below: parameter description protocol name select the protocol name option here. Rate limit enter the rate limit value u...

  • Page 530: Storm Control

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 518 traffic segmentation settings this window is used to display and configure the traffic segmentation settings. When the traffic segmentation forwarding domain is specified, packets received by the port will be restricted in l...

  • Page 531

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 519 figure 9-84 storm control window the fields that can be configured in storm control trap settings are described below: parameter description trap state select the storm control trap option here. Options to choose from are no...

  • Page 532

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 520 parameter description rise threshold is reached. Selecting drop specifies to discards packets that exceed the risen threshold. Level type select the level type option here. Options to choose from are pps, kbps, and level. Pp...

  • Page 533

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 521 click the apply button to accept the changes made. Dos attack prevention settings this window is used to display and configure the denial-of-service (dos) attack prevention settings. The following well-known dos types which ...

  • Page 534: Ssh

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 522 figure 9-87 dos attack prevention settings window the fields that can be configured in snmp server enable traps dos settings are described below: parameter description trap state select to enable or disable the dos attack pr...

  • Page 535: Ssh Global Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 523 • configure the user account to use a specified authorization method to identify users that are allowed to establish ssh connections with the switch using the ssh user authentication mode window. There are three choices as t...

  • Page 536: Ssh Server Connection

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 524 figure 9-89 host key window the fields that can be configured in host key management are described below: parameter description crypto key type select the crypto key type used here. Options to choose from are the rivest sham...

  • Page 537: Ssh User Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 525 to view the following window, click security > ssh > ssh server connection, as shown below: figure 9-92 ssh server connection window ssh user settings this window is used to display and configure the ssh user settings. To vi...

  • Page 538: Ssl Global Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 526 • key exchange: the first part of the cipher suite string specifies the public key algorithm to be used. This switch utilizes the rivest shamir adleman (rsa) public key algorithm and the digital signature algorithm (dsa), sp...

  • Page 539: Crypto Pki Trustpoint

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 527 parameter description ssl status select to enable or disable the global ssl status here. Service policy enter the service policy name here. This name can be up to 32 characters long. Click the apply button to accept the chan...

  • Page 540: Ssl Service Policy

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 528 click the apply button to accept the changes made. Click the find button to locate a specific entry based on the information entered. Click the delete button to remove the specified entry. Ssl service policy this window is u...

  • Page 541

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 529 note: only ipv4 sftp servers are supported. To view the following window, click security > sftp server settings, as shown below: figure 9-97 sftp server settings window the fields that can be configured are described below: ...

  • Page 542: 10.  Oam

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 530 10. Oam cfm cable diagnostics ethernet oam ddm cfm cfm settings this window is used to display and configure the connectivity fault management (cfm) settings. To view the following window, click oam > cfm > cfm settings, as ...

  • Page 543

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 531 parameter description easy identification of administrative responsibility for each maintenance domain. Domain level enter the maintenance domain (md) level here. The range is from 0 to 7. A unique md level is assigned to de...

  • Page 544

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 532 parameter description • chassis - specifies to transmit the sender id tlv with the chassis id information. • manage - specifies to transmit the sender id tlv with the managed address information. • chassis-manage - specifies...

  • Page 545

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 533 parameter description ma mode select the ma mode here. Options to choose from are: • software - specifies that the ma works in the cfm software mode. • hardware - specifies that the ma works in the cfm hardware mode. The cfm...

  • Page 546

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 534 after clicking the add mep button, the following page will appear. Figure 10-5 cfm settings (add ma, add mep) window the fields that can be configured are described below: parameter description mepid enter the mep id here. T...

  • Page 547

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 535 figure 10-6 cfm settings (add ma, add mep, mepid detail) window click the edit button to modify the specified entry. Click the back button to return to the previous window. After clicking the edit button, the following page ...

  • Page 548

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 536 figure 10-7 cfm settings (add ma, add mep, mepid detail, edit) window the fields that can be configured are described below: parameter description mep state select to enable or disable the mep state on the interface here. Cc...

  • Page 549

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 537 parameter description sent. Alarm time enter the time period used to define the time from when a defect is detected on the mep to when a fault alarm will be sent. The range is from 250 to 1000 centiseconds. By default, this ...

  • Page 550

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 538 after clicking the edit dm button, the following page will appear. Figure 10-10 cfm settings (add ma, add mep, edit dm) window the fields that can be configured in cfm dm settings are described below: parameter description s...

  • Page 551

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 539 parameter description default value is the pdu priority of the mep. Click the apply button to accept the changes made. The fields that can be configured in clear cfm dm are described below: parameter description type select ...

  • Page 552: Cfm Port Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 540 parameter description mac address enter the mac address for the lm test here. Period select the time period here. This specifies the transmitting interval of the lm pdu. Options to choose from are 100ms, 1sec, and 10sec. Pdu...

  • Page 553: Cfm Loopback Test

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 541 after clicking the show detail button, the following page will appear. Figure 10-13 cfm port settings (view detail) window click the back button to return to the previous window. Cfm loopback test this window is used to disp...

  • Page 554: Cfm Linktrace Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 542 parameter description pdu priority select the 802.1p priority to be set in the transmitted lbms here. If not specified, it uses the same priority as the ccms sent by the ma. The range is from 0 to 7. Select the none option t...

  • Page 555: Cfm Packet Counter

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 543 click the clear all button to clear the information associated with all entries. Click the show detail button to view more detailed information about the link-trace entry. After clicking the show detail button, the following...

  • Page 556: Cfm Counter Ccm

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 544 cfm counter ccm this window is used to view and clear the cfm ccm counter information. To view the following window, click oam > cfm > cfm counter ccm, as shown below: figure 10-18 cfm counter ccm window click the clear butt...

  • Page 557

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 545 figure 10-21 cable diagnostics window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the app...

  • Page 558: Ethernet Oam

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 546 ethernet oam ethernet oam settings this window is used to display and configure the ethernet operations, administration, and maintenance (oam) settings. To view the following window, click oam > ethernet oam > ethernet oam s...

  • Page 559

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 547 parameter description • process - specifies to react to remote loopback requirements from a peer. The feature is used to configure the client to process or to ignore the received ethernet oam remote loopback feature. In the ...

  • Page 560

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 548 figure 10-23 ethernet oam configuration settings window the fields that can be configured in ethernet oam configuration settings are described below: parameter description unit select the switch unit id that will be used her...

  • Page 561

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 549 parameter description • error frame seconds - this feature is used to enable notifying the ethernet oam error frame second event and configure the monitor threshold and window on the specified port. • error frame period - th...

  • Page 562

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 550 parameter description unit select the switch unit id that will be used here. From port - to port select the switch port range that will be used here. Click the find button to locate a specific entry based on the information ...

  • Page 563: Ethernet Oam Duld Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 551 figure 10-25 ethernet oam statistics table window the fields that can be configured are described below: parameter description unit select the switch unit id that will be used here. From port - to port select the switch port...

  • Page 564: Ddm

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 552 figure 10-26 ethernet oam duld settings window the fields that can be configured in ethernet oam duld settings are described below: parameter description recovery time enter the time interval value used by duld to decide how...

  • Page 565: Ddm Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 553 switch and to configure alarm settings, warning settings, temperature threshold settings, voltage threshold settings, bias current threshold settings, tx power threshold settings, and rx power threshold settings. Ddm setting...

  • Page 566

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 554 click the apply button to accept the changes made. Ddm temperature threshold settings this window is used to display and configure the ddm temperature threshold settings for specific ports on the switch. To view the followin...

  • Page 567

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 555 the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. Port select the port used for the configuration here. Action select the ...

  • Page 568

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 556 figure 10-31 ddm tx power threshold settings window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. Port select the port...

  • Page 569: Ddm Status Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 557 parameter description unit select the switch unit that will be used for this configuration here. Port select the port used for the configuration here. Action select the action that will be taken here. Options to choose from ...

  • Page 570: 11.  Mpls

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 558 11. Mpls mpls ldp information settings mpls lsp trigger information mpls forwarding settings mpls ldp neighbor password settings mpls ldp neighbor targeted settings mpls ldp neighbor information mpls global settings mpls ldp...

  • Page 571

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 559 parameter description max pdu length in this field the ldp maximum pdu length value will be displayed. Initial backoff enter the initial back-off delay time here. The ldp back-off delay time is a mechanism to prevent an endl...

  • Page 572

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 560 parameter description select the default option to use the default value, which is 254. Hop count limit enter the hop count limit here. The range is from 1 to 255. This feature is used to configure the maximum number of hops...

  • Page 573: Mpls Forwarding Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 561 figure 11-2 mpls lsp trigger information window the fields that can be configured are described below: parameter description sn enter the sequence number of the lsp trigger filter rule here. When creating a new rule, if not ...

  • Page 574

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 562 figure 11-3 mpls forwarding settings window the fields that can be configured for static ftn settings are described below: parameter description fec enter the fec ipv4 address of the static ftn here. Mask enter the fec subne...

  • Page 575

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 563 parameter description mask enter the fec subnet mask of the ftn here. Click the find button to locate a specific entry based on the information entered. Mpls ldp neighbor password settings this window is used to display and ...

  • Page 576

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 564 figure 11-5 mpls ldp neighbor targeted settings window the fields that can be configured are described below: parameter description neighbor targeted enter the lsr id of the targeted peer here. The targeted peer is used to e...

  • Page 577: Mpls Global Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 565 click the clear all button to clear all the mpls ldp neighbor information. Mpls global settings this window is used to display and configure the global mpls settings. To view the following window, click mpls > mpls global se...

  • Page 578

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 566 figure 11-8 mpls ldp interface settings window the fields that can be configured are described below: parameter description interface vid enter the interface vlan id used here. The range is from 1 to 4094. Ldp state select t...

  • Page 579

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 567 figure 11-9 mpls ldp session information window the fields that can be configured are described below: parameter description peer enter the ip address which is used as the peer lsr id here. Click the find button to locate a ...

  • Page 580: Mpls Ldp Statistic

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 568 figure 11-11 mpls ldp session information (show statistics) window click the back button to return to the previous window. Mpls ldp statistic this window is used to display mpls ldp statistics. To view the following window, ...

  • Page 581

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 569 figure 11-13 mpls ldp binding table window mpls ldp discovery information this window is used to display mpls ldp discovery information. To view the following window, click mpls > mpls ldp discovery information, as shown bel...

  • Page 582: Mpls Qos Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 570 enter a page number and click the go button to navigate to a specific page when multiple pages exist. Mpls qos settings this window is used to display and configure the mpls qos settings. To view the following window, click ...

  • Page 583

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 571 figure 11-18 mpls qos settings (edit) window click the add button to add a new entry. Click the delete button to remove the specific entry. Click the apply button to accept the changes made. Click the back button to return t...

  • Page 584

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 572 figure 11-20 mpls qos settings (edit, outbound cos to exp settings) window click the add button to add a new entry. Click the delete button to remove the specific entry. Click the apply button to accept the changes made. Cli...

  • Page 585: Ping Mpls

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 573 figure 11-22 mpls qos settings (edit, binding fecs settings) window the fields that can be configured are described below: parameter description ip enter the fec ip address here. Use this feature to apply an mpls qos policy ...

  • Page 586: Traceroute Mpls Ipv4

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 574 the fields that can be configured are described below: parameter description ipv4 address select and enter the fec ipv4 address here whose lsp connectivity will be checked. Mask select and enter the fec subnet mask here. Vc ...

  • Page 587

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 575 the fields that can be configured are described below: parameter description ipv4 address enter the fec ipv4 address here whose lsp connectivity will be checked. Mask enter the fec subnet mask here. Timeout enter the trace-r...

  • Page 588: 12.  Mpls L2Vpn

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 576 12. Mpls l2vpn vpws settings l2vc interface description vpls settings vpls mac address table vpws settings this window is used to display and configure the virtual private wire service (vpws) settings. To view the following ...

  • Page 589

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 577 parameter description vc id enter the pseudo-wire (pw) service instance id here. The range is from 1 to 4294967295. Click the apply button to accept the changes made. Click the find button to locate a specific entry based on...

  • Page 590

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 578 parameter description specified delay time after the primary pw comes back. The range is from 0 to 180 seconds. Selecting the never option specifies not to switch back to the primary pw even if it comes back. This is the def...

  • Page 591: L2Vc Interface Description

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 579 figure 12-3 vpws settings (show detail) window click the back button to return to the previous window. L2vc interface description this window is used to display and configure the layer 2 virtual circuit (l2vc) interface desc...

  • Page 592: Vpls Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 580 parameter description description enter the l2vc interface description here. This name can be up to 64 characters long. Click the apply button to accept the changes made. The fields that can be configured for find l2vc inter...

  • Page 593

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 581 parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the range of ports that will be used for this configuration here. Svid select and enter the svid her...

  • Page 594

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 582 parameter description to remote peers in this vpls here. The mtu value must be same at both the local and remote sites to establish the pw. If the mtu is specified as 0, then local the mtu will not be advertised to remote pe...

  • Page 595

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 583 the fields that can be configured for egress vlan mode settings are described below: parameter description egress vlan mode select the egress vlan mode of the vpls here. The egress vlan mode will affect the outer vlan tag ha...

  • Page 596: Vpls Mac Address Table

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 584 click the back button to return to the previous window. Vpls mac address table this window is used to clear and display vpls mac address information. To view the following window, click mpls l2vpn > vpls mac address table, a...

  • Page 597: 13.  Monitoring

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 585 13. Monitoring vlan counter utilization statistics mirror settings sflow device environment external alarm settings vlan counter this window is used to display and configure the vlan counter settings. This is used to create ...

  • Page 598: Utilization

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 586 parameter description • both - specifies to count ingress and egress traffic. Click the apply button to accept the changes made. Click the delete button to delete the specified entry based on the information entered/selected...

  • Page 599: History Utilization

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 587 history utilization this window is used to view the memory, cpu and port history utilization. To view the following window, click monitoring > utilization > history utilization, as shown below: figure 13-3 history utilizatio...

  • Page 600: Statistics

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 588 parameter description • cpu - specifies to display the historical cpu utilization information. • port - specifies to display the historical port utilization information. Unit select the switch unit that will be used here. Fr...

  • Page 601: Cpu Port

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 589 after clicking the show detail button, the following window will appear: figure 13-7 port (show detail) window click the back button to return to the previous window. Click the refresh button to refresh the information displ...

  • Page 602: Interface Counters

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 590 figure 13-8 cpu port window the fields that can be configured are described below: parameter description type select the type of information to display here. Options to choose from are all, layer 2 (l2), layer 3 (l3), and pr...

  • Page 603

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 591 figure 13-9 interface counters (port) window the fields that can be configured are described below: parameter description type select the type of information to display here. Options to choose from are port and vlan. Unit se...

  • Page 604

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 592 figure 13-10 interface counters (show errors) window click the back button to return to the previous window. Click the refresh button to refresh the information displayed in the table. After selecting vlan as the type, the f...

  • Page 605: Interface History Counters

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 593 interface history counters this window is used to view the history counter information per interface. To view the following window, click monitoring > statistics > interface history counters, as shown below: figure 13-12 int...

  • Page 606: Counters

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 594 click the find button to display entries in the table based on the information selected/entered. Counters this window is used to view and clear counter information. To view the following window, click monitoring > statistics...

  • Page 607

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 595 figure 13-14 counters (show detail) window click the back button to return to the previous window. Click the refresh button to refresh the information displayed in the table. After selecting vlan as the type, the following w...

  • Page 608: Mirror Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 596 the fields that can be configured are described below: parameter description type select the type of information to display here. Options to choose from are port and vlan. Interface vlan enter the vlan id that will be used i...

  • Page 609

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 597 the fields that can be configured for mirror settings are described below: parameter description session number select the mirror session number for this entry here. This number is between 1 and 4. Destination tick the check...

  • Page 610: Sflow

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 598 figure 13-17 mirror settings (show detail) window click the back button to return to the previous page. Sflow sflow agent information this window is used to view the sflow agent information. To view the following window, cli...

  • Page 611: Sflow Sampler Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 599 the fields that can be configured are described below: parameter description receiver index enter the index number of the receiver here. This number must be between 1 and 4. Owner name enter the owner name of the receiver he...

  • Page 612: Sflow Poller Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 600 parameter description • selecting outbound specifies to sample egress packets. Sampling rate enter packet sampling rate here. This value must be between 0 and 65536. Entering 0 will disable this function. If not specified, t...

  • Page 613: External Alarm Settings

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 601 figure 13-22 device environment window external alarm settings this window is used to display and configure the external alarm settings. This is used to enable monitoring the external alarm source status or to configure exte...

  • Page 614

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 602 parameter description message enter the alarm message associated with the channel here. This string can be up to 128 characters long. Click the apply button to accept the changes made. Click the default button return the ent...

  • Page 615: 14.  Green

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 603 14. Green power saving eee power saving this window is used to display and configure the power saving settings of the switch. To view the following window, click green > power saving, as shown below: figure 14-1 power saving...

  • Page 616: Eee

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 604 note: the hibernation feature can only be configured when physical stacking is disabled on this switch. After clicking the power saving shutdown settings tab, the following page will appear. Figure 14-2 power saving shutdown...

  • Page 617

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 605 the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. From port - to port select the appropriate port range used for the confi...

  • Page 618: 15.  Save and Tools

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 606 15. Save and tools save configuration firmware upgrade & backup configuration restore & backup log backup ping trace route reset reboot system dlms settings save configuration this window is used to save the running configur...

  • Page 619: Firmware Upgrade From Ftp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 607 parameter description unit select the switch unit that will be used for this configuration here. Source file in this field the source firmware file’s filename and path will be displayed after selection. To navigate to the lo...

  • Page 620: Firmware Upgrade From Rcp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 608 figure 15-4 firmware upgrade from ftp window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. Ftp server ip enter the ftp...

  • Page 621: Firmware Backup to Http

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 609 the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. Rcp server ip enter the rcp server ip address here. User name enter the ...

  • Page 622: Firmware Backup to Ftp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 610 figure 15-7 firmware backup to tftp window the fields that can be configured are described below: parameter description unit select the switch unit that will be used for this configuration here. Tftp server ip enter the tftp...

  • Page 623: Firmware Backup to Rcp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 611 parameter description selected, enter the ipv6 address of the ftp server in the space provided. Tcp port enter the tcp port number used for the ftp connection here. The range is from 1 to 65535. User name enter the user name...

  • Page 624

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 612 configuration restore & backup configuration restore from http this window is used to initiate a configuration restore from a local pc using http. To view the following window, click tools > configuration restore & backup > ...

  • Page 625

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 613 parameter description unit select the switch unit that will be used for this configuration here. Tftp server ip enter the tftp server ip address here. When select the ipv4 option, enter the ipv4 address of the tftp server in...

  • Page 626

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 614 parameter description long. Source file enter the source filename and path of the configuration file located on the ftp server here. This field can be up to 64 characters long. Destination file enter the destination path and...

  • Page 627

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 615 configuration backup to http this window is used to initiate a configuration file backup to a local pc using http. To view the following window, click tools > configuration restore & backup > configuration backup to http, as...

  • Page 628: Configuration Backup to Ftp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 616 parameter description destination file enter the destination path and location where the configuration file should be stored on the tftp server. This field can be up to 64 characters long. Click the backup button to initiate...

  • Page 629: Configuration Backup To Rcp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 617 configuration backup to rcp this window is used to initiate a configuration file backup to an rcp server. To view the following window, click tools > configuration restore & backup > configuration backup to rcp, as shown bel...

  • Page 630: Log Backup to Tftp

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 618 parameter description • when the system log option is selected, the system log will be backed up. • when the attack log is selected, the attack log will be backed up. Click the backup button to initiate the system log backup...

  • Page 631: Ping

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 619 the fields that can be configured are described below: parameter description rcp server ip enter the rcp server ip address here. User name enter the user name used for the rcp connection here. This name can be up to 32 chara...

  • Page 632

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 620 figure 15-21 ping window the fields that can be configured in ping access class are described below: parameter description acl name enter the name of the acl that will be used here. This name can be up to 32 characters long....

  • Page 633

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 621 parameter description timeout select a timeout period between 1 and 99 seconds for this ping message to reach its destination. If the packet fails to find the ip address in this specified time, the ping packet will be droppe...

  • Page 634: Trace Route

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 622 figure 15-22 ping (please select) window select the radio button next to the entry to use that acl in the configuration. Enter a page number and click the go button to navigate to a specific page when multiple pages exist. C...

  • Page 635

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 623 figure 15-24 trace route window the fields that can be configured in ipv4 trace route are described below: parameter description vrf name enter the name of the vrf instance here. This name can be up to 12 characters long. Ip...

  • Page 636: Reset

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 624 parameter description default value is 1. Click the start button to initiate the route trace for each individual section. The fields that can be configured in ipv6 trace route are described below: parameter description ipv6 ...

  • Page 637: Reboot System

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 625 figure 15-26 reset window select one of the following options: • the switch will reset to its factory default settings and then reboot. • the switch will reset to its factory default settings and then reboot. This option exc...

  • Page 638

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 626 to view the following window, click tools > dlms settings, as shown below: figure 15-29 dlms settings window the fields that can be configured are described below: parameter description unit select the switch unit id that wi...

  • Page 639

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 627 appendix a - password recovery procedure this section describes the procedure for resetting passwords on the d-link dgs-3630 series switch. Authenticating any user who tries to access networks is necessary and important. The...

  • Page 640

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 628 appendix b - system log entries the following table lists all possible entries and their corresponding meanings that will appear in the system log of this switch. 802.1x log description severity event description: 802.1x aut...

  • Page 641

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 629 log description severity event description: login failed due to aaa server timeout or improper configuration. Log message: login failed through from due to aaa server timeout (username: ). Parameters description: exec-type: ...

  • Page 642

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 630 log description severity username: it indicates the username for authentication. Event description: radius assigned a valid priority attributes. Log message: radius server assigned 802.1p default priority: to port (username:...

  • Page 643

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 631 auto-save log description severity event description: record the event when the configure information of ddp is saved automatically. Log message:config-6-ddpsaveconfig: [unit , ]configuration automatically saved to flash due...

  • Page 644

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 632 log description severity ipaddr: ip address of bgp peer. Event description: bgp connection is closed due to receive notify packet. (error code and error subcode refer to rfc) log message: bgp-4-notifyclose: bgp connection is...

  • Page 645

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 633 bpdu protection log description severity event description: record the event when the bpdu attack happened. Log message: enter stp bpdu under protection state (mode: ) parameters description: interface-id: interface on which...

  • Page 646

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 634 log description severity mepid: represents the mepid of the mep. Macaddr: represents the mac address of the mep. Event description: remote mep's mac reports an error status log message: cfm remote mac error. Md level:, vlan:...

  • Page 647

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 635 log description severity mdlevel: represents the md level of the mep. Interface-id: represents the interface number of the mep. Mepdirection: represents the direction of the mep. This can be "inward" or "outward". Mepid: rep...

  • Page 648

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 636 log description severity macaddr : represent client mac address. Serverip: server ip address. Pathfile: path and file name on server. Event description: firmware uploaded unsuccessfully. Log message: [unit , ]firmware upload...

  • Page 649

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 637 log description severity event description: configuration uploaded unsuccessfully. Log message: [unit ] configuration uploaded by unsuccessfully. (username: [, ip: , mac: ], server ip: , file name: ) parameters description: ...

  • Page 650

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 638 log description severity parameters description: interface-id: port interface id. Component: ddm threshold type. It can be one of the following types: temperature supply voltage bias current tx power rx power high-low: high ...

  • Page 651

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 639 log description severity ipv6address: ipv6 address obtained from a dhcpv6 server. Ipif-name: name of the dhcpv6 client interface. Event description: the ipv6 address obtained from a dhcpv6 server renews success. Log message:...

  • Page 652

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 640 log description severity parameters description: ipv6address: ipv6 prefix obtained from a delegation router. Intf-name: name of the dhcpv6 client pd interface. Event description: the ipv6 prefix obtained from a delegation ro...

  • Page 653

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 641 log description severity : activation code event description: license successfully installed. Log message: license successfully installed (license:, ac: ). Parameters description: : license model name. : activation code info...

  • Page 654

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 642 dynamic arp inspection log description severity event description: detect illegal arp packet log message: illegal arp packets (ip: , mac: , vlan , on ). Parameters description: type: the type of arp packet, it indicates that...

  • Page 655

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 643 log description severity parameters description: macaddr: mac address instanceid: instance id event description: "rpl owner conflicted. Log message: "rpl owner conflicted on the node (mac: , instance )" parameters descriptio...

  • Page 656

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 644 log description severity parameters description: interface-id: the interface name. Event description: remote loopback stop log message: oam remote loopback stopped (port ) parameters description: interface-id: the interface ...

  • Page 657

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 645 log description severity event description: link aggregation group link up. Log message: link aggregation group link up. Parameters description: group_id: the group id of the link up aggregation group. Informational event de...

  • Page 658

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 646 log description severity parameters description: none lldp-med log description severity event description: lldp-med topology change detected log message: lldp-med topology change detected (on port . Chassis id: , , port id: ...

  • Page 659

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 647 log description severity 1. Interfacealias(1) 2. Portcomponent(2) 3. Macaddress(3) 4. Networkaddress(4) 5. Interfacename(5) 6. Agentcircuitid(6) 7. Local(7) portid: port id. Deviceclass: lldp-med device type. Event descripti...

  • Page 660

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 648 log description severity username: represent current login user. Event description: console session timed out. Log message: [unit , ] console session timed out (username: ) parameters description: unitid: the unit id. Userna...

  • Page 661

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 649 log description severity parameters description: username: represent current login user. Ipaddr: represent client ip address. Mac log description severity event description: the host has passed mac authentication log message...

  • Page 662

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 650 log description severity event description: lsp is up log message: lsp is up parameters description: lsp_id: the established lsp id informational event description: lsp is down log message: lsp is down parameters description...

  • Page 663

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 651 log description severity portnum: port id/ old_role: old role new_status: new role event description: spanning tree instance created. Log message: spanning tree instance created. (instance:) parameters description: instancei...

  • Page 665

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 653 peripheral log description severity event description: fan recovered. Log message: unit , back to normal parameters description: unit : the unit id. : for example, right fan, left fan etc. Critical event description: fan fai...

  • Page 666

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 654 log description severity port: represents the logical port number. Nway: represents the speed and duplex of link. Event description: port linkdown log message: port link down parameters description: port: represents the logi...

  • Page 667

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 655 log description severity parameters description: entry-name: the name for this schedule execute configuration entry filename: the filename of the configuration. Time-range: the name of the time range. Event description: sche...

  • Page 668

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 656 log description severity event description: ssh server is enabled. Log message: ssh server is enabled informational event description: ssh server is disabled. Log message: ssh server is disabled informational ssl log descrip...

  • Page 669

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 657 log description severity stack_tp_type: the stacking topology type is one of the following: 1. Ring, 2. Chain. Unitid: box id. Macaddr: mac address. Event description: backup master changed to master. Log message: backup mas...

  • Page 670

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 658 log description severity packets interface-id: the interface id on which a storm is occurring. Event description: storm cleared. Log message: storm is cleared on . Parameters description: broadcast: broadcast storm is cleare...

  • Page 671

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 659 log description severity log message: broadcast storm is occurring. Parameters description: interface-id: the interface name. Event description: broadcast storm cleared. Log message: broadcast storm has cleared. Parameters d...

  • Page 672

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 660 log description severity vc_id: the link down pseudowire id ipaddr: the peer ip address of the link down pseudowire event description: pseudowire link up log message: pseudowire id peer ip link up parameters description: vc_...

  • Page 673

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 661 log description severity intf-name: interface name on which virtual router is based. Auth-type: vrrp interface authentication type. Event description: checksum error of one received vrrp advertisement message. Log message: r...

  • Page 674

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 662 log description severity vrrp-mac-addr: vrrp virtual mac address vrrp-errcode: errcode of vrrp protocol behavior. Event description: failed when adding a virtual mac into switch l3 table. The l3 table is full. Log message: f...

  • Page 675

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 663 log description severity event description: when a client host fails to authenticate. Log message: wac unauthenticated user (user name: , ip: ipv6address>, mac: , port: ) parameters description: string: user name ipaddr: ip ...

  • Page 676

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 664 log description severity username: the use name that used to login http server. Ipaddr: the ip address of http client..

  • Page 677: Appendix C - Trap Entries

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 665 appendix c - trap entries the following table lists all possible trap log entries and their corresponding meanings that will appear in the switch. 802.1x trap name description oid ddot1xextloggedsuccess the trap is sent when...

  • Page 678

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 666 authentication fail trap name description oid authenticationfailure an authenticationfailure trap signifies that the snmpv2 entity, acting in an agent role, has received a protocol message that is not properly authenticated....

  • Page 679

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 667 cfm extension trap name description oid dcfmaisoccurred this trap is initiated when local mep enters ais status. Binding objects: (1) dcfmeventmdindex (2) dcfmeventmaindex (3) dcfmeventmepidentifier 1.3.6.1.4.1.171 .14.86.0....

  • Page 680

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 668 trap name description oid ddhcpfilterattackdetected when dhcp server screen is enabled, if the switch received the forge dhcp server packet, the switch will trap the event if any attacking packet is received. Binding objects...

  • Page 681

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 669 trap name description oid dexternalalarmstatuschg the commander switch will send this notification when external alarm state is changed. Binding objects: (1) dexternalalarmunitid (2) dexternalalarmchannel (3) dexternalalarms...

  • Page 682

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 670 trap name description oid (1) ifindex, (2) if adminstatus (3) ifoperstatu lbd trap name description oid swportloopoccurred the trap is sent when a port loop occurs. Binding objects: (1) swloopdetectportindex 1.3.6.1.4.1.171 ...

  • Page 683

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 671 trap name description oid (1) lldpstatsremtablesinserts (2) lldpstatsremtablesdeletes (3) lldpstatsremtablesdrops (4) lldpstatsremtablesageouts lldpxmedtopologychangedetected a notification generated by the local device sens...

  • Page 684

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 672 trap name description oid mplsxcup this notification is generated when the mplsxcoperstatus object for one or more contiguous entries in the mplsxctable is about to enter the up state from another state. 1.3.6.1.2.1.10. 166....

  • Page 685

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 673 trap name description oid pimneighborloss a pimneighborloss notification signifies the loss of an adjacency with a neighbor. This notification should be generated when the neighbor timer expires, and the router has no other ...

  • Page 686

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 674 port security trap name description oid dportsecmacaddrviolation when the port security trap is enabled, new mac addresses that violate the pre-defined port security configuration will trigger trap messages to be sent out. B...

  • Page 687

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 675 trap name description oid is configured for sending snmp traps. Binding objects: (1) alarmindex (2) alarmvariable (3) alarmsampletype (4) alarmvalue (5) alarmfallingthreshold safeguard trap name description oid dsafeguardchg...

  • Page 688

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 676 trap name description oid (1) swsingleipmsid (2) swsingleipmsmacaddr swsingleipmsnewroot the commander switch will send this notification when its member generates a new root notification. Binding objects: (1) swsingleipmsid...

  • Page 689

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 677 storm control trap name description oid dstormctrloccurred this trap is sent when dstormctrlnotifyenable is 'stormoccurred' or 'both' and a storm is detected. Binding objects: (1) ifindex, (2) dstormctrlnotifytraffictype 1.3...

  • Page 690

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 678 trap name description oid the notpresent (5) state. Pwup this notification is generated when the pwoperstatus object for one or more contiguous entries in the pwtable which are about to enter the up (1) state from some other...

  • Page 691

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 679 appendix d - radius attributes assignment the radius attributes assignment on the switch is used in the following modules: console, telnet, ssh, web, 802.1x, mac-based access control, and wac. The description that follows ex...

  • Page 692

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 680 to assign the 802.1p default priority by the radius server, the proper parameters should be configured on the radius server. The table below shows the parameters for 802.1p default priority. The parameters of the vendor-spec...

  • Page 693

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 681 note: a tag field of greater than 0x1f is interpreted as the first octet of the following field. If the user has configured the vlan attribute of the radius server (for example, vid 3) and the 802.1x, or mac based access con...

  • Page 694

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 682 appendix e - ietf radius attributes support remote authentication dial-in user service (radius) attributes carry specific authentication, authorization, information and configuration details for the request and reply. This a...

  • Page 695

    Dgs-3630 series layer 3 stackable managed switch web ui reference guide 683 radius accounting attributes: number ietf attribute 1 user-name 4 nas-ip-address 5 nas-port 6 service-type 8 framed-ip-address 31 calling-station-id 32 nas-identifier 40 acct-status-type 41 acct-delay-time 42 acct-input-octe...