D-Link DI-106 Series Faq

Other manuals for DI-106 Series: User Manual
Manual is about: remote access router with integrated Ethernet hub

Summary of DI-106 Series

  • Page 1

    D-link co.,_______________________________________________________________________ faq faq: 1 d-link router family frequently asked questions (faq) part i: general product overview questions 1. What is the router product family? The router family of products are a set of multiprotocol remote access ...

  • Page 2

    D-link co.,_______________________________________________________________________ faq faq: 2 the router incorporates features not present on most of their competitors' products. Internet single user account (sua) support please see subject 9 for details. Multiprotocol router the router is the only ...

  • Page 3

    D-link co.,_______________________________________________________________________ faq faq: 3 you can configure your router remotely through a modem call. This setup requires an external ‘local’ modem. Local remote v v [router]--[null modem]-[modem]--(phone line)--[modem]-[computer] ^ rs-232 cable t...

  • Page 4

    D-link co.,_______________________________________________________________________ faq faq: 4 b. Allow icmp (including ping) menu 21.1.2 - tcp/ip filter rule filter #: 1,2 filter type= tcp/ip filter rule active= yes ip protocol= 1 ip source route= no ^^^^^^^^^^^^^^^ destination: ip addr= 0.0.0.0 ip ...

  • Page 5

    D-link co.,_______________________________________________________________________ faq faq: 5 active= yes ip protocol= 6 ip source route= no ^^^^^^^^^^^^^^^ destination: ip addr= 0.0.0.0 ip mask= 0.0.0.0 port #= 1023 ^^^^ port # comp= greater ^^^^^^^ source: ip addr= 0.0.0.0 ip mask= 0.0.0.0 port #=...

  • Page 6

    D-link co.,_______________________________________________________________________ faq faq: 6 port # comp= none tcp estab= no more= no log= none action matched= forward ^^^^^^^ action not matched= check next rule h. The your menu 21.1 will look like menu 21.1 - filter rules summary # a type filter r...

  • Page 7

    D-link co.,_______________________________________________________________________ faq faq: 7 in menu 1: - set route ip to ‘yes’. In menu 3.2: - set ip address to an address on ‘my-net’ (a). In menu 4: - set isp ip addr to ‘c’. - make sure single user account is set to ‘no’. In order for the nodes o...

  • Page 9

    D-link co.,_______________________________________________________________________ faq faq: 9 in menu 1: - set route ipx to ‘yes’. In menu 3.3: - determine what frame type the client and server(s) stations are using and set the appropriate frame type to ‘yes’. The router will not be able to communic...

  • Page 10

    D-link co.,_______________________________________________________________________ faq faq: 10 - set call direction to ‘outgoing’. - set route to ‘ipx’, and select ‘yes’ to editing the ipx options. In menu 11.3: - set dial-on-query to ‘yes’. - set rem lan net # to the internal network number of the ...

  • Page 11

    D-link co.,_______________________________________________________________________ faq faq: 11 - set active to ‘yes’. - set network # to ‘00000222’ (the internal network number of the server). - set gateway node to the number of the remote node (1- 4) for this setup. The remote isdn router (cisco, a...

  • Page 12

    D-link co.,_______________________________________________________________________ faq faq: 12 netware netware client server the router can place calls to a remote isdn router to bridge ipx packets. In this configuration, the stations on the lan (my-net) will have access to the ipx netware server an...

  • Page 13

    D-link co.,_______________________________________________________________________ faq faq: 13 if you are using the ip pool: - set ip start addr as ip address assigned to the remote station (c). - set ip count(1,2) to be the number of ip addresses in the pool. In menu 14.1: - set user name to be the...

  • Page 14

    D-link co.,_______________________________________________________________________ faq faq: 14 in menu 14.1: - set user name to be the login name for the remote station. - set passwd to be the password for the remote station. 6. How do i configure my router to work with other devices? Cisco router m...

  • Page 15

    D-link co.,_______________________________________________________________________ faq faq: 15 for the outgoing data filters: - deny "bounceback" packets - allow packets that originate from us filter type= tcp/ip filter rule active= yes destination: ip addr= a.B.C.D destination: ip mask= w.X.Y.Z act...

  • Page 16

    D-link co.,_______________________________________________________________________ faq faq: 16 currently, the only method available for backing up and restoring the router’s configuration is locally through the rs-232 port. Menu 24.5 and 24.6 provide simple methods to perform the backup and restorat...

  • Page 17

    D-link co.,_______________________________________________________________________ faq faq: 17 get to the remote node configuration screen, select ‘yes’ to edit the ppp options. There are two ways to setup the mp call: a. Set base trans rate to ‘128’. This will bring up both channels every time the ...

  • Page 18

    D-link co.,_______________________________________________________________________ faq faq: 18 source: ip addr= 0.0.0.0 ip mask= 0.0.0.0 port #= 137 port # comp= equal tcp estab= n/a more= no log= none action matched= drop action not matched= forward menu 21.1.2 - tcp/ip filter rule filter #: 1,3 fi...

  • Page 19

    D-link co.,_______________________________________________________________________ faq faq: 19 to prevent certain ipx packets from triggering a call to a remote node. These filters should inform your router which packets should be ignored as traffic. If you are routing ipx packets, the default call ...

  • Page 20

    D-link co.,_______________________________________________________________________ faq faq: 20 (system management terminal) has a system timeout of five minutes. That is, if you do not perform a keyboard operation in five minutes then the screen will blank out or your telnet connection will be dropp...

  • Page 21

    D-link co.,_______________________________________________________________________ faq faq: 21 9. Dial-in users to the router cannot talk to some or all of the stations on the lan side of router, or access internet through another router on the lan (dial-in user are using ip address in ip pool) why?...

  • Page 22

    D-link co.,_______________________________________________________________________ faq faq: 22 concurrently for the cost of a single user. Nat is a generic name defined in rfc 1631 "the ip network address translator (nat)". Sua (internet single user account) is d- link's implementation and trade nam...

  • Page 23

    D-link co.,_______________________________________________________________________ faq faq: 23 with that phone number. 5. How do i use the syslog feature to account for my calls? The router can be configured to send unix syslogs to a host on the lan that runs a syslog daemon (most unix systems will ...

  • Page 24

    D-link co.,_______________________________________________________________________ faq faq: 24 1) put the most restrictive things at the front. This syslog.Conf will get everything from local 0,1,2, no matter what level it is, and send it to d-link_log 2) use tabs!!!! No spaces! 7. What are the debu...

  • Page 25

    D-link co.,_______________________________________________________________________ faq faq: 25 > ip ping a.B.C.D (where a.B.C.D is the remote gateway ip address) (after the call stops) > sys trcl disp you will see the tracelog as well as the packet traces. 7.C can’t ping to or from the lan on the ro...

  • Page 26

    D-link co.,_______________________________________________________________________ faq faq: 26 > ip route stat the ‘use’ for the route to that remote node should have been incremented. If it hasn’t then examine the routing table to determine why. Check whether the call has been triggered by using > ...

  • Page 27

    D-link co.,_______________________________________________________________________ faq faq: 27 12. How does the router assign its calling party id numbers for outgoing calls? The router assigns these numbers based on the phone numbers you enter in menu 2. 13. Can you clarify the capabilities of the ...

  • Page 28

    D-link co.,_______________________________________________________________________ faq faq: 28 clu is the current line utilization. It's the percentage of the total bandwidth being used. Alu is the average line utilization. It's the percentage of the average bandwidth used. The calculation of these ...

  • Page 29

    D-link co.,_______________________________________________________________________ faq faq: 29 this procedure, please refer to: maintenance of the user’s guide. 3. What can i do if i have problems upgrading my system code? If you have any problems when you upload the system code, try uploading the c...