1. DL manuals
  2. D-Link
  3. Switch
  4. DMC-1002
  5. User Manual

D-Link DMC-1002 User Manual

Manual is about: User Manual

Summary of DMC-1002

  • Page 1

    Rev. 01 (jun. 2002) 1907mcb10016000 recyclable snmp module for chassis-based media converter manual dmc-1002.

  • Page 2: About This Guide

    1 t abl e of c ont en t s about this guide .................................................................. 2 f eatures ........................................................................................................2 u npacking ................................................................

  • Page 3

    2 a bout t hi s g u i de this manual shows you how to configuring your dmc-1002 snmp module for chassis-based media converter. Features compliant with ieee802.3u 100base-tx standards enable to monitor the module through terminal emulation program and web browser the network administrator can access ...

  • Page 4

    3 c onf i guri ng t h e s y s t em this chapter provides network managers and system administrators with information about how to configure the media converter chassis system. The reader of this document should be knowledgeable about network devices, device configuration, network management, and int...

  • Page 5

    4 configure through web browser the media converter chassis system is accessible using a web browser (ie explorer, netscape communications, etc.) to open up the chassis monitoring system. The default ip address for the chassis system is “192.168.1.1”, and the default login name and password is both ...

  • Page 6

    5 5. The default login name and password is both “root”. Support snmp management the media converter management module support snmp management. Led indicators the led indicators of the switch include power, alert, http, icq, smtp, speed, link/act and fdx/col. The following shows the led indicators f...

  • Page 7

    6 link/act: lights green when link to networking ethernet and blinks green for activity. M anage me nt s e t t i n g t hr ou gh w e b b row s er 1 main menu figure (1) main menu 1-1 system function there are four items in system function menu, “software reboot, factory reset, image update and config...

  • Page 8

    7 figure (2) configuration 1-1-1 software reboot to reboot for the software setting. 1-1-2 cpu factory reset this function is to set the cpu (dmc-1002) back to the default setting in case of the messy setting. 1-1-3 factory reset this function is to set both cpu (dmc-1002) and all system (all smart ...

  • Page 9

    8 while the file is uploading to the system, it will appear a warning sign. (figure 3.2) figure (3.1) figure (3.2).

  • Page 10

    9 1-1-5 configuration update figure (4) the section is explaining how to upload and download the configure setting of the module. The configuration upload is to restore a setting file to the management module. The configuration download is to backup the setting from the management module. 1-2-1 gene...

  • Page 11

    10 figure (5) hardware revision: noted the version of the hardware. Bios revision: noted the version of the bios. Firmware revision: noted the version of the firmware. Change password: the changing of the admit password. Confirm password: to confirm the setting of admit password. System name: to aut...

  • Page 12

    11 default ip is “192.168.1.1”. Subnet mask: to set the subnet mask, the default is “255.255.255.0”. Default gateway: to set the gateway address, the default is “192.168.1.254”. Note: after configuring the system device, need to press the save button to save the setting. 1-2-3 snmp configuration fig...

  • Page 13

    12 cold start trap: to set the trap for rebooting the device (default = enable). Authentication fail trap: to set the warning trap when the community name of the device and workstation are different (default = enable) . Power fail trap: to set the power fail trap (default = enable). Fan fail trap: t...

  • Page 14

    13 m anage me nt s e t t i n g t hr ou gh t e r mi n a l e mul ator 2 main menu figure (8) 2-1 system function there are three items in system function menu, “software reboot, factory reset, image update. (figure 9) figure (9) 2-1-1 software reboot to reboot for the software setting. 2-1-2 factory r...

  • Page 15

    14 this function is to set the device back to the default setting in case of the messy setting. 2-1-3 image update figure (10) the section is to set the tftp server ip address first, and the default address was set to “192.168.1.2”. The image file can be updated by uploading the image file from the ...

  • Page 16

    15 there are four items in the configuration menu, “general configuration, system configuration, media converter chassis, media converters status and media converters setting. (figure 11) 2-2-1 general configuration figure (12) hardware revision: noted the version of the hardware. Bios revision: not...

  • Page 17

    16 figure (13) mac address: will show out the mac address of the device. Ip address: to allocate an ip address for the device, the default ip is “192.168.1.1”. Subnet mask: to set the subnet mask, the default is “255.255.255.0”. Default gw: to set the gateway address, the default is “192.168.1.254”....

  • Page 18

    17 figure (14) the screen will show out the power status of the chassis system. V stands for “yes” and x stands for “no”. Plug in: indicates if power 1 or 2 was plugged in or not. Power fail: indicates if the power 1 or 2 is fail or not. Fan fail: indicates if the fan 1 or 2 is fail or not. 2-2-4 me...

  • Page 19

    18 converter. 2-2-4 media converters status figure (15.2) to control the linkage of each media converter. 2-3 snmp configuration figure (16) get community name: to get the device community name (default = public) . Set community name: to set the device community name (default = private)..

  • Page 20

    19 trap community name: to authorize the device trap community name (default = public). Trap host ip address: to set the trap host ip address (same as monitoring station ip address). Cold start trap: to set the trap for rebooting the device (default = enable). Authentication fail trap: to set the wa...

  • Page 21

    20 t e chni cal s p e c if i c at i ons general standards ieee 802.3 10base-t; ieee 802.3u 100base-tx protocol csma/cd data transfer rate 100mbps (half-duplex) 200mbps (full-duplex) topology star network cables 10base-t – 2-pair utp cat. 3,4,5, up to 100 m (328 ft) 100base-tx -- 2-pair utp cat. 5, u...