- DL manuals
- D-Link
- Network Router
- DSL-3580L
- User Manual
D-Link DSL-3580L User Manual
Summary of DSL-3580L
Page 2: Table Of Contents
Table of content table of contents package contents .................................................................. 4 system requirements ............................................................ 5 introduction ............................................................................. 6 fea...
Page 3
Table of content ipv6 status ....................................................................... 108 ipv6 routing info ........................................................... 109 troubleshooting ................................................................ 110 appendix ......................
Page 4: Package Contents
Section 1 - product overview package contents • dsl-3580l series wireless ac1200 dual-band gigabit adsl2+ modem router • 2 internal antenas (mimo 2x2) • power adapter • cd-rom with installation wizard, user manual, and special offers • one twisted-pair telephone cable used for adsl connection • one ...
Page 5: System Requirements
Section 1 - product overview system requirements 1. Adsl internet service computer with: • 200mhz processor • 64mb memory • cd-rom drive • ethernet adapter with tcp/ip protocol installed • windows win7/vista/xp/2000z • mac os • internet explorer v6 or later, firefox v1.5 2. Dcc (d-link click's conne...
Page 6: Introduction
Section 1 - product overview 11 introduction high-speed wan (adsl2/2+ or gigabit ethernet wan) internet connection latest adsl2/2+ standards provide internet transmission of up to 24mbps downstream, 2.7mbps upstream. Gigabit ethernet wan offers you plenty of bandwidth once you decide to employ ether...
Page 7: Features
Section 1 - product overview features • faster wireless networking - the dsl-3580l series router provides up to 866mbps* wireless connection with other 802.11ac wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and r...
Page 8
Section 1 - product overview *maximum wireless signal rate derived from ieee standard 802.11ac specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual ...
Page 9
Section 1 - product overview hardware overview – connections power insert use the adapter shipped with the router to connect to power source power button push in to power-on the router. Push again to power-off the router adsl port use the adsl cable to connect to the your telephone line (rj-11 port)...
Page 10
Section 1 - product overview hardware overview – led indication power steady green light indicates the unit is powered on. When the device is powered off this remains dark. Dsl steady green light indicates a valid adsl connection. This will light after the adsl negotiation process has been settled. ...
Page 11: Installation
Section 2 - installation installation this section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage. Before you begin please read and make sure you understand al...
Page 12: Installation Notes
Section 2 - installation installation notes in order to establish a connection to the internet it will be necessary to provide information to the router that will be stored in its memory. For some users, only their account information (username and password) is required. For others, various paramete...
Page 13
Section 2 - installation d-link dsl-3580l series user manual 13.
Page 14
Section 2 - installation 802.11 wireless lan configuration all the 802.11 wireless lan settings may be configured on a single page using the web-based manager. For basic wireless communication you need to decide what channel to use and what ssid to assign. These two settings must be the same for any...
Page 15: Provider
Section 2 - installation information you need from the internet service provider username this is the username used to log on to your adsl service provider’s network. It is commonly in the form user@isp.Co.Uk. Your adsl service provider uses this to identify your account. Password this is the passwo...
Page 16
Section 2 - installation vpi most users will not be required to change this setting. The virtual path identifier (vpi) is used in conjunction with the virtual channel identifier (vci) to identify the data path between your adsl service provider’s network and your computer. If you are setting up the ...
Page 17
Section 2 - installation information you need to know about dsl-3580l system administrator username this is the username needed access the router’s management interface. When you attempt to connect to the device through a web browser you will be prompted to enter this username. The default username ...
Page 18
Section 2 - installation information you will need about your lan or computer : ethernet nic if your computer has an ethernet nic, you can connect the dsl-3580l to this ethernet port using an ethernet cable. You can also use the ethernet ports on the dsl-3580l to connect to other computer or etherne...
Page 19
Section 2 - installation wireless installation considerations dsl-3580l lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other ob...
Page 20: Device Installation
Section 2 - installation device installation dsl-3580l series daul band 802.11ac wireless adsl2+ gigabit ethernet router maintains four separate interfaces, an ethernet lan, a wireless lan, an ethernet wan and an adsl internet (wan) connection. Carefully consider the router’s location suitable for c...
Page 21: Factory Reset Button
Section 2 - installation factory reset button the router may be reset to the original factory default settings by using a ballpoint or paperclip to gently push down the reset button in the following sequence: 1.Press and hold the reset button (the button just beside power button) while the device is...
Page 22
Section 2 - installation hub or switch to router connection connect the router to an uplink port (mdi-ii) on an ethernet hub or switch with a straight-through 8p4c rj-45 ethernet cable as shown in this diagram. If you wish to reserve the uplink port on the switch or hub for another device, connect t...
Page 23: Configuration
Section 3 - configuration configuration this section will show you how to configure your new d-link wireless router using the web-based configuration utility. Web-based configuration utility connect to the router to configure the wan connection used by the router it is first necessary to communicate...
Page 24: Setup
Section 3 - configuration setup this chapter is concerned with using your computer to configure the wan connection. The following chapter describes the various windows used to configure and monitor the router including how to change ip settings and dhcp server setup. Wizard the wizard allows you to ...
Page 25
Section 3 - configuration welcome to the setup wizard this wizard will guide user through a step-by-step wizard, divided into 7 steps, to configure this router and to connect to the internet. Click the next button to continue to the next page. Click the cancel button to discard the changes made and ...
Page 26
Section 3 - configuration step 2: select your time zone in this step the user can configure the time zone settings that will be used by this router. Click the prev to return to the previous page click the next to continue to the next page click the cancel to cancel the setup wizard click the connect...
Page 27
Section 3 - configuration please enter an ssid to do so. The default name is d-link dsl-2875al. Please note that the length of the 5g ssid must be between 3 and 32 alphanumeric characters only including hyphens and spaces. In this section we can configure the following parameters. 2.4g wireless netw...
Page 28
Section 3 - configuration best: select this option if your wireless adapters support wpa2. Better: select this option if your wireless adapters support wpa. Good: select this option if your wireless adapters do not support wpa. None: select this option if you do not want to activate any security fea...
Page 29
Section 3 - configuration on the next page register mydlink™ cloud services account if you already have mydlink™ account, use the existing account name/password to register your mydlink™ account directly if you don’t have the mydlink™ account, you can fill up the required information and create a ne...
Page 30
Section 3 - configuration name). Password: enter the password. Confirm password: enter the confirm password. First name: enter the first name. Last name: enter the last name. Click the sign up button to sign up mydlink™ cloud services account. Click the prev button to discard the changes made and re...
Page 31: Wan Setup
Section 3 - configuration wan setup to access the wan setup ettings window, click on the internet setup button in the setup directory in this page: operation mode adsl router: the device will use the dsl line as its wan interface residential gateway: the device will use eth wan as its wan interface ...
Page 32
Section 3 - configuration choose the internet connection mode your isp is using. D-link dsl-3580l series user manual 32.
Page 33
Section 3 - configuration for pppoe/pppoa internet connection type: type in the username and password (and pppoe service name, if required by your isp). You can use static ipv4 address check box and type static ip. Set mtu value which you want but should be less than 1492. Nat: check this checkbox i...
Page 34
Section 3 - configuration note: after mydlink™ registration is completed, your router’s default pppoe connection will be set to “always-on”. If your isp changes for usage, you may wish to manually choose “dial on demand” as your default setting, however, mydlink™ features may not work as intended. F...
Page 35
Section 3 - configuration for static ip address internet connection type type ip address, subnet mask, default gateway, and select connection in drop-down menu. These information should be provided from your internet service provider (isp) nat: check this checkbox if you want your device to translat...
Page 36
Section 3 - configuration for bridge connection type service category: to setup the atm qos function, you may need to consult your isp for this setting enable vlan: to enable/disable vlan (0-4095) function on your wan interface which was assigned by your isp d-link dsl-3580l series user manual 36.
Page 37
Section 3 - configuration residential gateway mode to use eth wan as your internet connection dynamic ip address: the device will obtain the ip address from your isp via eth wan directly static ip address: you can configure the fixed ip address (assigned by your isp) manually if you choose “static i...
Page 38: Wireless Setup
Section 3 - configuration wireless setup use this section to configure the wireless settings for your d-link router. To access the wireless (wlan) settings window, click on the wireless setup button in the setup tab. Wireless network setting click on the add wireless device with wps button. This wiz...
Page 39
Section 3 - configuration add wireless device with wps the wizard shows the option to setup wps by auto or manual. Auto -- select this option if your wireless device supports wps(wi-fi protected setup) manual -- select this option to display the current wireless settings for you to configure the wir...
Page 40
Section 3 - configuration add wireless device with wps (wi-fi protected setup) wizard this page will count down the timer and please start wps on the wireless device you are adding in time. Add wireless device with wps (manually) this screen shows the information for the ssid, wireless security mode...
Page 41
Section 3 - configuration manual wireless connection setup settings dsl-3580l comes with 2 physical wireless interfaces (known 2.4ghz and 5ghz). Click on the enable wireless box to activate the wireless interface. You can use the add new button to create a schedule and apply to the wireless interfac...
Page 42
Section 3 - configuration channel bandwidth 2.4g wireless interface with 2.4g interface, you can choose 20mhz (up to 150mbps) or auto 20/40mhz to achieve maximum performance of 300mbps (at 40mhz)* remark: when 20/40mhz is employed, wireless ap will dynamically scan the wireless channel condition. An...
Page 43
Section 3 - configuration wireless security mode to protect your privacy you can configure wireless security features. This device supports three wireless security modes including: wep, wpa, wpa2, auto (wpa or wpa2). Wep is the original wireless encryption standard. Wpa provides a higher level of se...
Page 44
Section 3 - configuration wireless security mode – wpa-personal use wpa or wpa2 mode to achieve a balance of strong security and best compatibility. This mode uses wpa for legacy clients while maintaining higher security with stations that are wpa2 capable. Also the strongest cipher that the client ...
Page 45
Section 3 - configuration wpa / wpa2 (enterprise) some network-security experts now recommend that wireless networks use 802.1x security measures to overcome some weaknesses in standard wep applications. A radius server is used to authenticate all potential users. . Enter your radius server data: ip...
Page 46: Lan Setup
Section 3 - configuration lan setup you can configure the lan ip address to suit your preference. Many users will find it convenient to use the default settings together with dhcp service to manage the ip settings for their private network. The ip address of the router is the base address used for d...
Page 47
Section 3 - configuration add/edit dhcp reservation (optional) select the enable to let you reserve the ip address for the designated pc with the configured mac address. Computer name is user defined meaningful host name which can help you recognize each pc connecting to the device. Clicking on the ...
Page 48: Time And Date
Section 3 - configuration time and date the time and date configuration option allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the ntp (network time protocol) server. Daylight saving can ...
Page 49
Section 3 - configuration time setting: check the automatically synchronize with internet time servers select specific time server to use from the first ntp time server and second ntp time server specific ntp server name. Time configuration: select your operating time zone from the time zone drop-do...
Page 50
Section 3 - configuration european union, you must select march, last, sunday. The time must depend on your country’s time zone. For example, in germany you must type 2 because germany’s time zone is 1 hour ahead of gmt or utc (gmt+1). Thus, in germany you must use march, last, sunday, at 1:00 a.M. ...
Page 51: Ipv6 Setup
Section 3 - configuration ipv6 setup the ipv6 configuration option allows you configure ipv6 internet connection. You can configure follow ipv6 internet connection setup wizard utilize or manually ipv6 internet connection setup. To access the ipv6 setting window, click on the ipv6 button in the setu...
Page 52
Section 3 - configuration ipv6 connection type: link-local only lan ipv6 address setting link-local only is communication with in internal network. The lan ipv6 link-local address is used as default setting. D-link dsl-3580l series user manual 52.
Page 53
Section 3 - configuration ipv6 connection type: static ipv6 wan ipv6 address settings you can check use link-local address box to link-local only, or type the wan ipv6 address and subnet prefix length. Type default gateway, primary ipv6 dns server and secondary ipv6 dns server. These information pro...
Page 54
Section 3 - configuration d-link dsl-3580l series user manual 54.
Page 55
Section 3 - configuration ipv6 connection type: autoconfiguration (slaac/dhcpv6) ipv6 dns setting choose obtain ipv6 dns servers automatically or type primary ipv6 dns server and secondary ipv6 dns server. Lan ipv6 address settings enable dhcp-pd to used prefix delegationassigned ipv6 prefix. Or you...
Page 56
Section 3 - configuration ipv6 connection type: pppoe pppoe session set share with ipv4 at address mode if you choose dynamic ip, router will obtained wan ipv6 address by dynamically or you can set static ipv6 address in static ip address/prefix length to router. Type user name, password, verify pas...
Page 57
Section 3 - configuration slaac+rdnss to set computers on router network obtained ipv6 address by rdnss stateful dhcp to set computers on router network obtained ipv6 address by stateful dhcp, you need type the ipv6 address range (start and end) ipv6 connection type: ds-lite choose ds-lite dhcpv6 op...
Page 58: Usb Setup
Section 3 - configuration usb setup the dsl router comes with a usb 2.0 interface which you can connect a usb printer, a usb storage device (e.G. Usb disk / usb external hard disk) or a usb 3g modem. To configure the usb device on the router, click usb setup in the setup tab. Router can be configure...
Page 59
Section 3 - configuration usb storage file server usb storage server allows you to share your usb storage device to all the connected local hosts. First connect your usb storage device to the usb port. Then enter the data below. To configure usb port to usb storage server setting, choose enable usb ...
Page 60
Section 3 - configuration samba file server enable samba file server to configure usb storage device as a samba file server. Setup the server name, server description and group name of file server. You can remote access when the remote access was hooked. You can check add, edit and delete the user i...
Page 61
Section 3 - configuration web file server tick enable web server to configure usb storage device as a web based file server. Click the browse to choose a folder for path, and type port number of web file server. You can remote access when the remote access was hooked. 3g usb modem setup click setup ...
Page 62: Mydlink™ Settings
Section 3 - configuration mydlink™ settings to access the mydlink™ settings page, click on the setup menu link, at the top, and then click on the mydlink™ settings menu link, on the left. Devices that are mydlink-enabled can be accessed and managed through the mydlink website and by using mydlink mo...
Page 63: Advanced
Section 3 - configuration advanced this chapter includes the more advanced features used for network management and security as well as administrative tools to manage the router, view status and other information used to examine performance and for troubleshooting. D-link dsl-3580l series user manua...
Page 64: Port Forwarding
Section 3 - configuration port forwarding use the port forwarding window to open ports in your router and re-direct data through those ports to a single pc on your network (wan-to-lan traffic). The port forwarding function allows remote users to access services on your lan such as ftp for file trans...
Page 65
Section 3 - configuration application rules configuration some applications such as games, video conferencing and remote access applications require specific ports on the router's firewall to be opened for the applications to pass through. To access application rules setting windows, click on the ap...
Page 66: Qos Setup
Section 3 - configuration qos setup quality of service setup can be used to improve data flow for different applications by prioritizing the network traffic based on selected criteria. To access the qos setup settings window, click on the qos setup button in the advanced tab qos setup you have to de...
Page 67
Section 3 - configuration wireless qos rules configuration type the policy name on the name, set the priority value on the priority. Select the protocol, any, icmp, tcp and udp. Set the source ip range and the destination ip range. Set the source port range and the destination port range. Click the ...
Page 68: Outbound Filter
Section 3 - configuration outbound filter by default, all outgoing ip traffic from the lan is not restricted. The outbound filter allows you to create a filter rule to block outgoing ip traffic by specifying a filter name and at least one condition below. All of the specified conditions in this filt...
Page 69: Inbound Filter
Section 3 - configuration inbound filter remark: inbound filter feature must work in conjunction with firewall feature. In order to use the inbound filter feature, you will have to create the filter policy reflecting to application scenario. Only the packet which can satisfy the filter policy will a...
Page 70
Section 3 - configuration add inbound ip filter to create the new policy and fill in the filter name. To pick up icmp, tcp/udp, tcp or udp from protocol. To type in source ip address, source subnet mask and source port (can be single port or port range in “start port::end port” syntax ) type destina...
Page 71: Wireless Filter
Section 3 - configuration wireless filter this feature can let you add a policy to deny or allow wlan devices connected to the router to access the wireless filter settings window, click on the wireless filter button in the advanced tab wireless filter policy you can choose the disable/ allow all/ d...
Page 72: Dns Setup
Section 3 - configuration dns setup the dns feature is designed for resolving the dns host name into ips. Unless you want the router query the specific dns servers; otherwise, you can leave the setting as obtain dns server address automatically. The dynamic dns feature allows you to host a server (w...
Page 73
Section 3 - configuration ddns configuration please enable the enable dynamic dns if you want to use ddns. Choose which ddns web site to use on the server address. Type which host name which you registered with your ddns service provider. On the host name. Please choose which interface name to use o...
Page 74: Firewall & Dmz
Section 3 - configuration firewall & dmz the router already provides a simple firewall by virtue of the way nat works. By default nat does not respond to unsolicited incoming requests on any port, thereby making your wan invisible to internet cyber attackers. Dmz means 'de militarized zone'. Dmz all...
Page 75
Section 3 - configuration dmz setting please tick the enable dmz and type the dmz computer ip on the dmz ip address or you also can choose the dmz host from the drop-down menu instead of type in ip manually. Application level gateway (alg) configuration please choose the following alg to enable: • p...
Page 76: Advanced Adsl
Section 3 - configuration advanced adsl the advanced adsl setting page allows you to do further configurations under dsl phase. Advanced adsl settings please select following adsl profile to link. G.Dmt, g.Lite, t1.413, adsl2, annexl, adsl2+, annex m (available only on annex a model) please choose t...
Page 77: Advanced Wireless
Section 3 - configuration advanced wireless these options are for users that wish to change the behavior of their wireless radio from the standard setting. D-link does not recommend changing these settings from the factory default. Incorrect settings may impair the performance of your wireless radio...
Page 78
Section 3 - configuration guest wireless setting guest wireless domain, only available on 2.4ghz interface, is an isolated zone from device lan and main ssid domain. Please enable the enable wireless guest network type ssid on the wireless network name please choose visible or invisible on the visib...
Page 79: Advanced Lan
Section 3 - configuration advanced lan these options are for users that wish to change the lan settings. D-link does not recommend changing these settings from factory default. Changing these settings may affect the behavior of your network. To access the advanced lan setting window, click on the ad...
Page 80: Port Mapping
Section 3 - configuration port mapping port mapping supports multiple ports to pvc and bridging groups. Each group will perform as an independent network. To support this feature, you must create mapping groups with appropriate lan and wan interfaces using the add button. The remove button will remo...
Page 81
Section 3 - configuration port mapping confuguration type group name and select wan interface used in the grouping in drop-down menu choose grouped lan interface from available lan interfaces. Type dhcp vendor ids in the automatically add clients with the following dhcp vendor ids for auto add clien...
Page 82: Snmp Setup
Section 3 - configuration snmp setup simple network management protocol (snmp) allows a management application to retrieve statistics and status from the snmp agent in this device. Select the desired values and click "apply" to configure the snmp options. To access the snmp setup setting window, cli...
Page 83: Parental Control
Section 3 - configuration parental control parental control provides two useful tools for restricting internet access. Block websites allows you to quickly create a list of all web sites that you wish to stop users from accessing. Time restrictions allows you to control when clients connected to rou...
Page 84: Routing Setup
Section 3 - configuration routing setup over the routing setup page, you can configure static routing policies or rip protocol settings. To access the routing setting window, click on the routing button under the advanced tab. Routing -- static route enter the destination network address, subnet mas...
Page 85
Section 3 - configuration routing -- rip configuration allows you to configure rip (routing information protocol). To activate rip for the device, select the 'enabled' radio button for global rip mode. To configure an individual interface, select the desired rip version and operation, followed by pl...
Page 86: Wi-Fi Protected Setup
Section 3 - configuration wi-fi protected setup wi-fi protected setup (also known as wps) is a standard designed to pair up a new joined client devices to a ap network by using a pin or hardware push button. In order to pair up ap and wireless client, you have to ensure both ap and client devices mu...
Page 87: Ipv6 Firewall
Section 3 - configuration ipv6 firewall the firewall settings section is an advance feature used to allow or deny traffic from passing through the device. It works in the same way as ip filters with additional settings. You can create more detail rules for the device. To access the ipv6 firewall set...
Page 88
Section 3 - configuration schedule rule click add button to add a new schedule. Add schedule rule type name for this rule and select day(s), you can sele all week or select day(s). Check all day-24hr or set start time to end time d-link dsl-3580l series user manual 88.
Page 89: Ipv6 Routing
Section 3 - configuration ipv6 routing this routing page allows you to specify custom routes that determine how data is moved around your network. A maximum 20 entries can be configured to access the ipv6 routing setting window, click on the ipv6 routing button in the advance table static ipv6 route...
Page 90: Budget Quota
Section 3 - configuration budget quota budget quota is a traffic meter feature offers • traffic quota metering on the user specified interface over the user defined period • traffic quota metering in different direction (both ingress and egress direction) • interface locking down in order to prevent...
Page 91: Logout
Section 3 - configuration logout the logout page enables you to logout of management gui and as well closes the browser. To access the logout setting window, click on the logout button in the setup tab logout click on the logout button to logout of the router configuration settings and close the web...
Page 92: Maintenance
Section 3 - configuration maintenance click on the maintenance tab to reveal the window buttons for various functions located in this directory. Password the factory default password of this router is 'admin'. To help secure your network, d-link recommends that you should choose a new password. To a...
Page 93: Save/restore Settings
Section 3 - configuration save/restore settings the device firmware offers you configuration backup feature which you can back up the configuration settings as a plan text file and store on your computer hard drive. You also have the option to restore configuration settings, or reset the device conf...
Page 94: Firmware Update
Section 3 - configuration firmware update use the firmware upgrade window to load the latest firmware for the device. Note that the device configuration settings may return to the factory default settings, so make sure you first save the configuration settings with the save/restore settings window d...
Page 95: Remote Management
Section 3 - configuration remote management this section allows you to enable/disable remote access to the router from the internet. Advanced access control allows you to configure access via specific services. Most users will not need to change any of these settings. To access the remote management...
Page 96: Diagnostics
Section 3 - configuration diagnostics your router is capable of testing your dsl connection. The individual tests are listed below. If a test displays a fail status, click "return diagnostics tests" at the bottom of this page to make sure fail status is consistent. If the test continues to fail, cli...
Page 97: Ping Test
Section 3 - configuration ping test the tests on this page can be used to verify whether or not your router is working correctly. If you have rerun the tests and consulted the help file and you are still experiencing difficulties, to access the ping test setting window, click on the ping test diagno...
Page 98: System Log
Section 3 - configuration system log the system log allows you to configure local, remote and email logging, and to view the logs that have been created. To access the system log setting window, click on the system log button under the maintenance tab. Remote log setting check log enable box: log le...
Page 99
Section 3 - configuration enable email notification please enable. If any logs occur, the system will send mail to the mail address you set. Email settings please input the from mail address, to mail address and smtp server address. Please enable the enable authentication and then set the account na...
Page 100: Schedule
Section 3 - configuration schedule schedule allows you to create scheduling rules to be applied for your firewall. Maximum of 16 entries to access the schedule rule setting window, click on the schedule rule button under the maintenance tab. Schedule rule press add / edit / delete button to modify y...
Page 101: Status
Section 3 - configuration status click on the status tab to reveal the window buttons for various functions located in this directory. The device status window is the first item in the status directory. Use these windows to view system information and monitor performance. Device info the device info...
Page 102
Section 3 - configuration internet info this window displays wan information including ip address, mask, default gateway, primary/secondary dns server. Wireless lan this session displays the 2.4ghz and the 5ghz wireless interface on/off status, ssid names, wireless channel selected and security mode...
Page 103
Section 3 - configuration local network info this window displays lan information including mac, ip address, mask, and dhcp server. Usb 3g dongle info this session show you usb 3g dongle signal strength and as well the operation mode. When 3g internet connection is dropped unexpectedly, you can chec...
Page 104: Connected Clients
Section 3 - configuration connected clients this feature shows all the client devices and computers currently associated wirelessly or connected over ethernet lan. To access the wireless clients setting window, click on the connected clients button in the status tab. Connected wireless clients this ...
Page 105: Statistics
Section 3 - configuration statistics this information reflects the current status of your router. To access the statisics window, click on the logs button in the statisics tab. Wan statistics this window displays all the receiver and transmitted packet status on the wan interface. Lan statistics thi...
Page 106
Section 3 - configuration adsl statistics this window displays all the adsl status you can click the adsl ber test button to test the adsl connection. You can click the reset statistics button to set all statistics to recount. D-link dsl-3580l series user manual 106.
Page 107: Routing Info
Section 3 - configuration routing info to access the route info setting window, click on the route info button under the status tab. The route info section displays route information showing the ip addresses of the destination, gateway, and subnet mask as well as other route information d-link dsl-3...
Page 108: Ipv6 Status
Section 3 - configuration ipv6 status to access the ipv6 status setting window, click on the ipv6 status button under the status tab. All of your ipv6 internet and network connection details are displayed on this page. D-link dsl-3580l series user manual 108.
Page 109: Ipv6 Routing Info
Section 3 - configuration ipv6 routing info to access the ipv6 routing info setting window, click on the ipv6 routing info button under the status tab. This routing page displays the ipv6 routing policies currently configured on your router. D-link dsl-3580l series user manual 109.
Page 110: Troubleshooting
Section 4 - troubleshooting troubleshooting this chapter provides solutions to problems that can occur during the installation and operation of the dsl-3580l. Read the following descriptions if you are having problems. (the examples below are illustrated in windows® xp. If you have a different opera...
Page 111
Section 4 - troubleshooting • configure your internet settings: • go to start > settings > control panel. Double-click on the internet options icon. From the security tab, click on the button to restore the settings to their defaults. • click on the connection tab and set the dial-up option to never...
Page 112: Appendix
Appendix a - wireless basics appendix wireless basics d-link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the ieee standard, the d-link wire...
Page 113
Appendix a - wireless basics d-link dsl-3580l series user manual 113.
Page 114
Appendix a - wireless basics wireless local area network (wlan) in a wireless local area network, a device called an access point (ap) connects computers to the network. The access point has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an i...
Page 115
Appendix a - wireless basics using a d-link cardbus adapter with your laptop, you can access the hotspot to connect to internet from remote locations like: airports, hotels, coffee shops, libraries, restaurants, and convention centers. Wireless network is easy to setup, but if you’re installing it f...
Page 116: Networking Basics
Appendix b - networking basics networking basics check your ip address after you install your new d-link adapter, by default, the tcp/ip settings should be set to obtain an ip address from a dhcp server (i.E. Wireless router) automatically. To verify your ip address, please follow the steps below. C...
Page 117
Appendix b - networking basics statically assign an ip address if you are not using a dhcp capable gateway/router, or you need to assign a static ip address, please follow the steps below: step 1 windows® xp - click on start > control panel > network connections. Windows® 2000 - from the desktop, ri...
Page 118: Fcc Caution
Appendix c – fcc caution fcc caution statement： this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cau...
Page 119: Ic Caution
Appendix d – ic caution ic caution english: this class b digital apparatus complies with canadian ices-003 and rss-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may ...
Page 120
Appendix e – contacting technical support contacting technical support you can find software updates and user documentation on the d-link websites. If you require product support, we encourage you to browse our faq section on the web site before contacting the support line. We have many faq’s which ...
Page 121: D-Link Link’N Print
Appendix – f d-link link’n print d-link link’n print introduction d-link link’n print allows you to share usb devices such as external storage drives and multifunction printers with other users across your network by simply connecting the device to select d-link routers. This allows you to use an ex...
Page 122
Appendix – f d-link link’n print installation 1. Insert the cd-rom into your computer. 2. Follow the on-screen instructions. 3. The icon should appear in the system tray at the lower-right corner on the desktop and a new icon should be created on the desktop. Set up the d-link router 1. Connect the ...
Page 123
Appendix – f d-link link’n print 7. The icon in the windows system tray should change to an icon. Connect usb devices to the d-link router the d-link link’n print automatically detects for each connected usb device. A window will pop up for each detected usb device. D-link dsl-3580l series user manu...
Page 124
Appendix – f d-link link’n print 1. Right-click on the icon. 2. Click on open d-link link’n print. 3. The d-link link’n print displays the connected usb devices on the network. To click “connect” to have the usb device connected. D-link dsl-3580l series user manual 124.
Page 125
Appendix – f d-link link’n print 4. Advanced options can be set by clicking on advanced options. D-link dsl-3580l series user manual 125.
Page 126
Appendix – f d-link link’n print virtually connect and disconnect a usb device 1. Move the cursor to waiting to connect and click on connect to virtually connect a usb device. 2. The d-link link’n print displays which user is virtually connecting this usb device. D-link dsl-3580l series user manual ...
Page 127
Appendix – f d-link link’n print 3. Move the cursor to in use by (owner) and click on disconnect to virtually disconnect the usb device. When the usb device is a multifunction printer d-link dsl-3580l series user manual 127.
Page 128
Appendix – f d-link link’n print 1. Move the cursor to waiting to connect and click on manage device. 2. Click yes on the question “do you want to install the printer software or mfp utility?” d-link dsl-3580l series user manual 128.
Page 129
Appendix – f d-link link’n print 3. Insert the cd-rom of the multifunction printer and follow the instructions to install the multifunction printer’s driver. When the installation process prompts you to connect the multifunction printer to your pc, click next. 4. The d-link link’n print virtually co...
Page 130
Appendix – f d-link link’n print 5. Choose the printer driver that you want d-link link’n print to auto-connect when you print. When you want to scan 1. Move the cursor to available for use and click on scan now. D-link dsl-3580l series user manual 130
Page 131: Technical Specifications
Appendix – f d-link link’n print technical specifications adsl standards • ansi t1.413 issue 2 • itu g.992.1 (g.Dmt) annexa • itu g.992.2 (g.Lite) annex a adsl2 standards • itu g.992.3 (g.Dmt.Bis) annex a • itu g.992.4 (g.Lite.Bis) annex a adsl2+ standards • itu g.992.5 annex a • itu g.992.5 annex m...