1. DL manuals
  2. D-Link
  3. Switch
  4. DXS-3600-16S
  5. Manual

D-Link DXS-3600-16S Manual

Manual is about: CLI Guide

Summary of DXS-3600-16S

  • Page 1

    Cli reference guide product model: dxs-3600 series layer 2/3 managed 10gbe switch release: 1.10

  • Page 2: Preface

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide ii dxs-3600 series cli reference guide software release f/w: 1.10.023 copyright statement all rights reserved. Without our written permission this document may not be excerpted, reproduced, transmitted, or otherwise in all or part by any par...

  • Page 3

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide iii notes, notices, and cautions below are examples of the 3 types of indicators used in this manual. When administering your switch using the information in this document, you should pay special attention to these indicators. Each example b...

  • Page 4

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide iv • operator - privilege level 12. This user account level is used to grant system configuration rights for users who need to change or monitor system configuration, except for security related information such as user accounts and snmp acc...

  • Page 5

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide v user exec mode at basic user level this command mode is mainly designed for checking basic system settings. This command mode can be entered by logging in as a basic user. Privileged exec mode at advanced user level this command mode is ma...

  • Page 6

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide vi interface configuration mode interface configuration mode is used to configure the parameters for an interface or a range of interfaces. An interface can be a physical port, vlan, or other virtual interface. Thus, interface configuration ...

  • Page 7: Table of Contents

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 1 table of contents basic cli commands................................................................................................................................................ 1 802.1x commands............................................

  • Page 8

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 2 route map commands.......................................................................................................................................... 523 secure shell (ssh) commands .....................................................

  • Page 9: Basic Cli Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 1 basic cli commands 1-1 help this command is used to display a brief description of the help system. Use the help command in any command mode. Help parameters none. Default none. Command mode exec mode privileged mode all configuration mode...

  • Page 10

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 2 1-2 prompt this command is used to customize the cli prompt. Execute the prompt command in global configuration mode. To revert to the default prompt, execute the no form of this command. Prompt string no prompt parameters 1-3 banner login...

  • Page 11

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 3 parameters c specifies the separator of the login banner message, for example a hash sign (#). The delimiting character is not allowed in the login banner message. Message enter the contents of the login banner, that will be displayed befo...

  • Page 12

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 4 1-4 exit this command is used to exit any configuration mode to the next highest mode in the cli mode hierarchy. Use the exit command in any configuration mode. If the current mode is the highest mode (exec mode, privileged mode) in the cl...

  • Page 13

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 5 end parameters none. Default none. Command mode exec mode privileged mode all configuration modes command default level level: 1 usage guideline execute this command to return back to the highest mode in the cli mode hierarchy regardless o...

  • Page 14: 802.1X Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 6 802.1x commands 2-1 dot1x default this command is used to reset the ieee 802.1x parameters on a specific port to their default settings. Dot1x default 2-2 dot1x port-control this command is used to manually control the authorization state ...

  • Page 15

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 7 2-3 dot1x pae authenticator this command is used to configure a specific port as an ieee 802.1x port access entity (pae) authenticator. Use the no form of this command to disable ieee 802.1x authentication on the port. Dot1x pae authentica...

  • Page 17

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 9 2-6 dot1x max-req this command is used to configure the maximum number of times that the backend authentication state machine will retransmit an extensible authentication protocol (eap) request frame to the supplicant before restarting the...

  • Page 19

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 11 2-10 dot1x system-auth-control this command is used to globally enable ieee 802.1x authentication on the switch. Use the no form of this command to disable ieee 802.1x function. Dot1x system-auth-control no dot1x system-auth-control 2-11 ...

  • Page 20

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 12 2-12 dot1x port-max-user this command is used to configure the maximum number of users that can be learned via 802.1x authentication on a specific port. Use the no form of this command to reset to the defaulting settings. Dot1x port-max-u...

  • Page 21

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 13 2-14 dot1x port-fwd-pdu this command used to control the forwarding of eapol pdus on specific ports. Use the no form of this command to reset to the defaulting settings. Dot1x port-fwd-pdu no dot1x port-fwd-pdu 2-15 show dot1x this comman...

  • Page 22

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 14 default none. Command mode privileged exec mode. Command default level level: 15 usage guideline use this command display the ieee 802.1x global configuration, interface configuration, authentication state, statistics, diagnostics, and se...

  • Page 23

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 15 example this example shows how to display the 802.1x statistics for the interface tengigabitethernet1/0/1. Dxs-3600-32s#show dot1x interface tengigabitethernet 1/0/1 statistics mac address : 00-00-00-00-00-02 interface : tengigabitetherne...

  • Page 24

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 16 example this example shows how to display the 802.1x session statistics for the interface tengigabitethernet1/0/1. Dxs-3600-32s#show dot1x interface tengigabitethernet 1/0/1 session-statistics mac address : 00-00-00-00-00-02 interface : t...

  • Page 25

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 17 access control list (acl) commands throughout this chapter, we'll refer to two abbreviates called: acl - access control list. Ace - access control entry 3-1 ip access-list standard this command is used to create or modify a standard ip ac...

  • Page 26

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 18 parameters 3-3 ip access-list extended this command is used to create or modify an extended ip acl. This command will enter into the extended ip access- list configuration mode. Use the no command to remove an extended ip access-list. Ip ...

  • Page 28

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 20 destination specifies the destination ip address. Destination-wildcard applies wildcard bits to the destination. Host destination specifies a specific destination ip address. Operator (optional) possible operators include ‘eq’ (equal), ‘g...

  • Page 29

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 21 3-5 ipv6 access-list this command is used to create or modify an ipv6 acl. This command will enter into the ipv6 access-list configuration mode. Use the no command to remove an ipv6 access-list. Ipv6 access-list {name} no ipv6 access-list...

  • Page 31

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 23 3-7 mac access-list this command is used to create or modify an extended mac acl. This command will enter into the extended mac access-list configuration mode. Use the no command to remove an extended mac access-list. Mac access-list exte...

  • Page 33

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 25 3-9 expert access-list this command is used to create or modify an extended expert acl. This command will enter into the extended expert access-list configuration mode. Use the no command to remove an extended expert access-list. Expert a...

  • Page 35

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 27 protocol specifies the name or number of an ip protocol used. Names that can be used are 'eigrp', 'esp', 'gre', 'igmp', 'ip', 'ipinip', 'ospf', 'pcp', 'pim', 'tcp', 'udp', 'icmp' or an integer in the range 0 to 255 representing an ip prot...

  • Page 37

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 29 3-12 list-remark text this command is used to add remarks for the specified acl. Use the no command to deletes the remarks. List-remark text no list-remark parameters 3-13 show access-lists this command is used to display all acls or the ...

  • Page 41

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 33 3-18 show access-group this command is used to display the acl configuration of the interface. Show access-group [interface interface] parameters name specifies the name of the expert acl to be configured. The name can be up to 32 charact...

  • Page 42

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 34 3-19 show ip access-group this command is used to display the ip acl configuration of the interface. Show ip access-group [interface interface] parameters 3-20 show ipv6 access-group this command is used to display the ipv6 acl configurat...

  • Page 43

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 35 3-21 show mac access-group this command is used to display the mac acl configuration of the interface. Show mac access-group [interface interface] parameters 3-22 show expert access-group this command is used to display the expert acl con...

  • Page 44

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 36 3-23 vlan access-map this command is used to create a submap. This command will enter into the access-map configuration mode. The no form of this command deletes the submap. Vlan access-map map_name [map_sn] no vlan access-map map_name [m...

  • Page 45

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 37 3-25 action this command is used to set the forwarding, drop, and redirect actions of submaps in the vacl mode. Use the no command to return to the default configuration. Action forward no action forward action drop no action drop action ...

  • Page 46

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 38 3-26 vlan filter this command is used to apply a hostmap in a vlan. Use the no command to remove a hostmap from a vlan. Vlan filter map_name vlan-list vlan_id no vlan filter map_name vlan-list vlan_id parameters 3-27 show vlan access-map ...

  • Page 48

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 40 address resolution protocol (arp) commands 4-1 arp this command is used to add a permanent ip address and mac address mapping to the arp cache table. Use the ‘no’ command to remove the ip-mac address mapping. Arp [vrf ] ip-address mac-add...

  • Page 49

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 41 4-3 clear arp cache this command is used to remove one or all dynamic arp entries from the arp cache table. Clear arp-cache [vrf ] [ip-address] [interface interface-name] parameters default the default timeout value is 20 minutes. Command...

  • Page 51

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 43 example this example shows how to display the arp cache table containing the ip address of 10.1.1.9. Dxs-3600-32s#show arp 10.1.1.9 arp timeout is 20 minutes. Interface ip address mac address type ------------- --------------- -----------...

  • Page 52

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 44 4-5 show arp counter this command is used to display the number of arp entries in the arp cache table. Show arp counter [vrf ] parameters 4-6 show arp timeout this command is used to display the aging time of a dynamic arp entry on the sw...

  • Page 53

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 45 show arp timeout 4-7 show ip arp this command is used to display the address resolution protocol (arp) cache table. Show ip arp [vrf ] parameters parameters none. Default none. Command mode privileged mode. Command default level level: 3 ...

  • Page 54

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 46 alternate store and forward (asf) commands 5-1 enable asf this command is used to enable the asf feature. Enable asf 5-2 no asf this command is used to disable the asf feature. No asf 5-3 show asf this command is to display the current as...

  • Page 55

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 47 example this example shows how to display the current settings for asf. Dxs-3600-32s#show asf alternate store and forward: disabled dxs-3600-32s#.

  • Page 56: Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 48 authentication, authorization, and accounting (aaa) commands 6-1 aaa this command is used to enable the authentication, authorization, and accounting (aaa) security service. The no form of this command is used to disable the aaa security ...

  • Page 57

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 49 6-3 aaa authentication enable this command is used to enable aaa enable authentication and configure the enable authentication method list. The no form of this command is used to delete the user authentication method list. Aaa authenticat...

  • Page 58

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 50 6-4 login authentication this command is used to apply the login authentication method list to the specified terminal lines. The no form of this command is used to remove the application of login authentication method list. Login authenti...

  • Page 59

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 51 parameters 6-6 aaa authorization console this command is used to enable authorization function for users who has logged in the console. The no form of this command is used to disable the authorization function. Aaa authorization console n...

  • Page 61

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 53 parameters 6-9 accounting exec this command is used to apply the exec accounting method list to the specified terminal lines in the line configuration mode. The no form of this command is used to disable the exec accounting function. Acco...

  • Page 62

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 54 6-10 ip http authentication aaa this command is used to specify an aaa authentication method for http server users, use the ip http authentication aaa command in global configuration mode. To disable a configured authentication method, us...

  • Page 63

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 55 6-11 aaa local authentication attempts this command is used to configure login attempt times. Aaa local authentication attempts max-attempts no aaa local authentication attempts 6-12 aaa local authentication lockout-time this command is u...

  • Page 64

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 56 6-13 aaa authentication network this command is used to enable aaa network access authentication and configure the network access user authentication method list. The no form of this command is used to delete the network access user authe...

  • Page 65

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 57 6-15 aaa accounting network this command is used to account users in order to count the network access fees. The no form of this command is used to disable the accounting function. Aaa accounting network default start-stop method1 [method...

  • Page 67

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 59 parameters 6-18 show aaa this command is used to display aaa security service global configuration, use the ‘show aaa’ command in exec mode. Show aaa ip-addr enter the ip address of the server. The host can be created via radius-server ho...

  • Page 68

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 60 6-19 show aaa server group this command is used to display aaa server group configuration, use the ‘show aaa server group’ command in exec mode. Show aaa server group 6-20 show aaa authentication this command is used to display the aaa au...

  • Page 71

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 63 example this example shows how to display aaa application line information. Dxs-3600-32s#show aaa application line console: login method list: default enable method list: default authorization method list: default accounting method list: ...

  • Page 72

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 64 6-24 ip vrf forwarding this command is used to configure the virtual private network (vpn) routing and forwarding (vrf) reference of an authentication, authorization, and accounting (aaa) radius or tacacs+ server group. Use this command i...

  • Page 74

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 66 7-3 aggregate-address this command is used to configure bgp aggregate entries. Use the no form of this command to delete the entry. Aggregate-address network-address [summary-only] [as-set] no aggregate-address network-address parameters ...

  • Page 75

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 67 7-4 bgp router-id this command is used to configure a fixed router id for the local border gateway protocol (bgp) routing process. Use the no form of this command to remove the fixed router id from the running configuration file and resto...

  • Page 76

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 68 7-6 bgp always-compare-med this command is used to enable the comparison of the multi exit discriminator (med) for paths from neighbors in different autonomous systems. Use the no form of this command to disallow the comparison. Bgp alway...

  • Page 77

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 69 7-7 bgp bestpath as-path ignore this command is used to not consider the as-path factor in selection of the best path. Use the no form of this command to restore default behavior and configure bgp to consider the as-path during route sele...

  • Page 78

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 70 7-9 bgp bestpath compare-routerid this command is used to compare the router id for identical ebgp paths. Use the no command to revert to disable this function. Bgp bestpath compare-routerid no bgp bestpath compare-routerid 7-10 bgp bestp...

  • Page 79

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 71 7-11 bgp bestpath med missing-as-worst this command is used to configure the bgp routing process to assign a value of infinity to routes that are missing the multi exit discriminator (med) attribute (making the path, without an med value,...

  • Page 80

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 72 7-13 bgp cluster-id this command is used to configure the cluster id of the route reflector. To remove the cluster id, use the no form of this command. Bgp cluster-id cluster-id no bgp cluster-id parameters command default level level: 8....

  • Page 81

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 73 7-14 bgp confederation identifier this command is used to specify the bgp confederation identifier. Use the no form of this command to remove the confederation identifier. Bgp confederation identifier as-number no bgp confederation identi...

  • Page 82

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 74 7-16 bgp dampening this command is used to enable bgp route dampening or to change the bgp route dampening parameters. To disable bgp dampening, use the no form of this command. Bgp dampening [[half-life reuse suppress max-suppress-time u...

  • Page 83

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 75 7-17 bgp default ipv4-unicast this command is used to enable the ipv4 unicast address family as the default address family for bgp peer session establishment. The no form of this command disables the default ipv4 unicast address family fo...

  • Page 84

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 76 7-18 bgp default local-preference this command is used to change the default local preference value. To return the local preference value to the default setting. Bgp default local-preference number no bgp default local-preference paramete...

  • Page 85

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 77 7-19 bgp deterministic-med this command is used to include the multi exit discriminator (med) value between all paths received from within the same autonomous system in the process of the best route selection. Use the no command to preven...

  • Page 86

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 78 7-21 bgp fast-external-fallover this command is used to configure the border gateway protocol (bgp) routing process to immediately reset external bgp peering sessions if the link used to reach these peers goes down. To disable the bgp fas...

  • Page 93

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 85 in (optional) specifies to initiate a soft reset for inbound routing information. Prefix-filter (optional) specifies to clear the existing outbound route filter (orf) prefix list to trigger a new route refresh or soft reconfiguration, whi...

  • Page 94

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 86 7-31 exit-address-family this command is used to exit from the address family configuration mode and enter the router configuration mode. Exit-address-family 7-32 ip as-path access-list this command is used to define a bgp autonomous syst...

  • Page 95

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 87 7-33 ip community-list this command is used to create a community list or add a community list entry to an existing community list. Use the no form of this command to delete the community list or one of its entries. Standard community lis...

  • Page 96

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 88 7-34 ip extcommunity-list this command is used to create an extended community list or add an extended community entry to an existing extended community list for vpn route filtering. Use the no form of this command to delete the extended ...

  • Page 97

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 89 extcommunity (optional) consists of a set of an rt value or a soo value. It can accept 12 values in total for one entry. There are two different types for the rt values or soo values: • ip address:number: the ip address should be a global...

  • Page 98

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 90 7-35 neighbor activate this command is used to enable the exchange of information with a border gateway protocol (bgp) neighbor. Use the no form of this command to disable the exchange of information with a bgp neighbor. Neighbor {ip-addr...

  • Page 100

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 422 43-3 speed this command is used to specify the speed of the ports. Speed {10

  • Page 101

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 93 parameters ip-address specifies the ip address of the bgp peer. Peer-group-name specifies the name of a border gateway protocol (bgp) peer group. The maximum length is 16 characters. Receive specifies to enable the orf capability in the r...

  • Page 102

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 94 7-40 neighbor default-originate this command is used to allow a bgp speaker (the local router) to send the default route 0.0.0.0 to a neighbor for use as a default route. To send no route as a default, use the no form of this command. Nei...

  • Page 108

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 100 peer-group-name specifies the name of a border gateway protocol (bgp) peer group. The maximum length is 16 characters. Default none. Command mode router configuration mode. Address family configuration mode (ipv4 unicast, vpnv4 and vrf)....

  • Page 109

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 101 7-48 neighbor peer-group (create group) this command is used to create a peer group. Use the no form of this command to delete a peer group. Neighbor peer-group-name peer-group no neighbor peer-group-name peer-group parameters as for the...

  • Page 115

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 107 7-55 neighbor send-community (vpnv4) this command used to specify whether the community attribute should be sent to a bgp neighbor or all the members of a peer group. Use the no form of this command to remove the entry. Neighbor {ip-addr...

  • Page 116

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 108 parameters 7-57 neighbor soft-reconfiguration inbound this command is used to start storing the route updates received from the specified neighbor or peer group. To not store received updates, use the no form of this command. Neighbor {i...

  • Page 119

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 111 parameters 7-61 neighbor update-source this command is used to allow bgp sessions to use any operational interface for tcp connections. Use the no form of this command to restore the interface assignment to the closest interface. Neighbo...

  • Page 123

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 115 7-66 router bgp this command is used to enable (configure) the bgp routing process. Use the no form of this command to remove a bgp routing process. Router bgp as-number no router bgp as-number parameters usage guideline this command is ...

  • Page 124

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 116 7-67 show ip as-path access-list this command is used to display configured as-path access-lists. Show ip as-path access-list [access-list-name] parameters access-list-name (optional) specifies the access list to be displayed. The length...

  • Page 126

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 118 example when one route’s as-path field is more than 160 characters, using this command, can only show 160 characters of the as-path field. Dxs-3600-32s#show ip bgp bgp local router id is 10.90.90.10 status codes: s suppressed, d damped, ...

  • Page 128

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 120 example the following example displays the bgp private labels of all routes. Dxs-3600-32s#show ip bgp all label bgp local router id is 30.1.1.2 status codes: s suppressed, d damped, h history, * valid, > best, i - internal origin codes: ...

  • Page 130

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 122 example the following example shows the bgp routing table in the vrf address family based on the route distinguisher. Dxs-3600-32s#show ip bgp rd 1:1 bgp local router id is 30.1.1.2 status codes: s suppressed, d damped, h history, * vali...

  • Page 132

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 124 default none. Command mode privileged mode. Command default level level: 3. (ei mode only command) usage guideline this command is used to display the bgp routing information invrf address family. Example the following example shows the ...

  • Page 133

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 125 7-72 show ip bgp aggregate this command is used to display the aggregate entry in the bgp (border gateway protocol) database. Show ip bgp aggregate [vrf vrf-name] [network-address] parameters status codes status of the table entry displa...

  • Page 135

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 127 example this example shows the output from the show ip bgp cidr-only command, in privileged mode. Dxs-3600-32s#show ip bgp cidr-only bgp local router id is 10.0.40.1 status codes: s suppressed, d damped, h history, * valid, > best, i - i...

  • Page 138

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 130 vrf vrf-name (optional) specifies the vrf name. The length of the vrf-name is 12 characters. Community-list-name specifies the community list name. The maximum length is 16 characters. Exact-match (optional) displays only routes that hav...

  • Page 139

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 131 7-76 show ip bgp confederation this command is used to display the confederation configuration of bgp. Show ip bgp confederation 7-77 show ip bgp dampening dampened-paths this command is used to display routes that were dampened by bgp. ...

  • Page 140

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 132 parameters vrf vrf-name (optional) specifies the vrf name. The length of the vrf-name is 12 characters. Default none. Command mode privileged mode. Command default level level: 3. (ei mode only command) usage guideline use this command t...

  • Page 141

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 133 7-78 show ip bgp dampening parameters this command is used to display the bgp dampening configuration. Show ip bgp dampening parameters [vrf vrf-name] parameters vrf vrf-name (optional) specifies the vrf name. The length of the vrf-name ...

  • Page 142

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 134 7-79 show ip bgp dampening flap-statistics this command is used to display bgp flap statistics. Show ip bgp dampening flap-statistics [vrf vrf-name] parameters suppress value a route is suppressed when its penalty exceeds this limit. The...

  • Page 144

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 136 example this example shows how to display the bgp route filter by content of access-list, as- acl_hq. Dxs-3600-32s#show ip bgp filter-list as-acl_hq bgp local router id is 10.90.90.90 status codes: s suppressed, d damped, h history, * va...

  • Page 147

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 139 parameters vrf vrf-name (optional) specifies the vrf name. The length of the vrf-name is 12 characters. Ip-address (optional) specifies the ip address of a neighbor. If this argument is omitted, all neighbors are displayed. Advertised-ro...

  • Page 148

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 140 (continued) bgp neighbor: 10.5.5.5 (external peer), vrf vpn-a ------------------------------------------------------------------- session state : enabled remote as : 2 remote router id : 0.0.0.0 bgp state : idle hold time : 180 seconds k...

  • Page 149

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 141 next hop self indicates whether the local bgp enable the router as the next hop for the neighbor. Description show the description configured to describe the neighbor. Password show the password set on the tcp connection to the neighbor....

  • Page 150

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 142 route map for incoming routes indicates a route map name which the route updates received from the neighbor must be applied. Route map for outgoing routes indicates a route map name which the route updates sent to the neighbor must be ap...

  • Page 151

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 143 origin codes origin of the table entry displayed at the end of each line. It can be one of the following values: i - entry originated from an interior gateway protocol (igp) and was advertised with a network router configuration command....

  • Page 152

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 144 display parameters description bgp local router id the router identifier of the local bgp router. Status codes status of the table entry displayed at the beginning of each line. It can be one or more of the following values: s - the tabl...

  • Page 153

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 145 origin codes origin of the table entry displayed at the end of each line. It can be one of the following values: i - entry originated from an interior gateway protocol (igp) and was advertised with a network router configuration command....

  • Page 154

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 146 7-83 show ip bgp network this command is used to display networks created by border gateway protocol network command. Show ip bgp network [vrf vrf-name] [network-address] parameters accepted prefixes number of routes accepted by the loca...

  • Page 155

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 147 7-84 show ip bgp redistribute this command is used to display the route redistribution configuration of bgp. Show ip bgp redistribute [vrf vrf-name] parameters example this example shows the output from the show ip bgp network command in...

  • Page 156

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 148 7-85 show ip bgp reflection this command is used to display the route reflection configuration of bgp. Show ip bgp reflection example this example shows how to display the redistribution configuration of bgp of the ip vrf address family:...

  • Page 158

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 150 7-87 show ip bgp parameters this command is used to display parameters of the border gateway protocol. Show ip bgp parameters example the following example displays routes that match the route-map map1 in vrf 100. Dxs-3600-32s#show ip bg...

  • Page 159

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 151 usage guideline this command displays the parameters of bgp. Example this example shows the output from the show ip bgp parameters command, in privileged mode. Dxs-3600-32s#show ip bgp parameters bgp global state : enabled version : 4 bg...

  • Page 161

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 153 display parameters description bgp peer group name of the peer group. Description show the description configured to describe the peer group session state indicates whether the peer group is shut down or not. Remote as remote as number o...

  • Page 163

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 155 example this example shows the output from the show ip bgp quote-regexp command, in privileged mode. Dxs-3600-32s#show ip bgp quote-regexp "100" bgp local router id is 10.90.90.10 status codes: s suppressed, d damped, h history, * valid,...

  • Page 165

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 157 7-91 show ip community-list this command is used to display configured community lists. Show ip community-list [community-list-name] parameters ver bgp protocol version. And now, value is 4. As the peer’s autonomous system number. Msgrcv...

  • Page 166

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 158 7-92 show ip extcommunity-list this command is used to display extened community lists configurations. Show ip extcommunity-list [extcommunity-list-name] parameters example this example shows that the output is similar to the output that...

  • Page 167

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 159 7-93 synchronization this command is used to enable the synchronization between bgp and your interior gateway protocol (igp) system. To enable the router to advertise a network route without waiting for the igp, use the no form of this c...

  • Page 168

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 160 7-94 timers bgp this command is used to adjust the bgp network timers. Use the no form of this command to restore to the default value. Timers bgp keep-alive hold-time no timers bgp parameters usage guideline usually, a bgp speaker does ...

  • Page 169

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 161 7-95 debug ip bgp this command is used to turn on the bgp debug function. Use the no form of this command to turn off the bgp debug function. Debug ip bgp no debug ip bgp 7-96 debug ip bgp fsm-event this command is used to turn on the bg...

  • Page 170

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 162 parameters 7-98 debug ip bgp route-map this command is used to turn on bgp route map debug switch. Use the no form of this command to turn off bgp route map debug switch. Debug ip bgp route-map no debug ip bgp route-map receive specifies...

  • Page 171

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 163 7-99 debug ip bgp prefix-list this command is used to turn on bgp ip prefix list debug switch. Use the no form of this command to turn off bgp ip prefix list debug switch. Debug ip bgp prefix-list no debug ip bgp prefix-list 7-100 debug ...

  • Page 174

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 166 7-103 debug ip bgp show network this command is used to show internal detailed information about the bgp network. Debug ip bgp show network [vrf vrf-name] parameters default none. Command mode privileged mode. Command default level level...

  • Page 175

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 167 7-104 debug ip bgp show aggregate this command is used to show internal detailed information about the bgp route aggregation. Debug ip bgp show aggregate [vrf vrf-name] parameters 7-105 debug ip bgp show damp this command is used to show...

  • Page 176

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 168 7-106 debug ip bgp show interface this command is used to show internal detailed information about the bgp interface. Debug ip bgp show interface command default level level: 15. (ei mode only command) usage guideline use this command to...

  • Page 177

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 169 7-107 debug ip bgp show timer this command is used to show internal detailed information about the bgp timer. Debug ip bgp show timer 7-108 debug ip bgp show redistribution this command is used to show internal detailed information about...

  • Page 178

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 170 parameters 7-109 debug ip bgp show as-path-access-list this command is used to show internal detailed information about the bgp path access list. Debug ip bgp show as-path-access-list vrf vrf-name (optional) specifies the vrf name. The l...

  • Page 179

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 171 7-110 debug ip bgp show community-list this command is used to show internal detailed information about the bgp community list. Debug ip bgp show community-list parameters none. Default none. Command mode privileged mode. Command default...

  • Page 180

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 172 compound authentication commands 8-1 network-access guest-vlan this command is used to specify an active vlan as a guest vlan for network-access authentication module. Use the no form of this command to return to the default setting. Net...

  • Page 181

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 173 8-3 network-access authentication-mode this command is used to configure the authentication mode for the network-access authentication module. Use the no form of this command to return to the default setting. Network-access authenticatio...

  • Page 182

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 174 default none. Command mode privileged exec mode. Command default level level: 3 usage guideline use the show network-access auth-configure command to display the authentication mode. Example this example shows the output from the show ne...

  • Page 183: Configuration Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 175 configuration commands 9-1 show running-config this command is used to show the configuration information of the current device’s system running. Show running-config 9-2 show bootup-config this command is used to view the boot-up configu...

  • Page 184

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 176 9-3 execute flash: this command is used to execute the configuration of device, stored in the nvram, by using the increment method. Execute flash: filename parameters example this example shows the boot-up configuration information store...

  • Page 186

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 178 example this example shows how to download the ‘config.Cfg’ file from the tftp server and replace the current running configuration with it. Dxs-3600-32s#configure replace tftp: //10.0.0.66/config.Cfg this will apply all necessary additi...

  • Page 187

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 179 9-5 boot config flash this command is used to specify the filename of the configuration file, stored in the nvram, from which the system configures itself during initialization (boot-up). Boot config flash filename parameters 9-6 copy ru...

  • Page 188

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 180 parameters bootup-config specifies to save the current running configuration and set it as the boot-up configuration file. If the boot-up configuration file exists, the boot-up configuration file will be replaced by current running confi...

  • Page 189

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 181 9-7 copy bootup-config this command is used to execute the boot-up configuration immediately, save the boot-up configuration to the nvram, or to upload the boot-up configuration to a tftp server or ftp server. Copy bootup-config {running...

  • Page 190

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 182 ftp: specifies that the startup configuration file will be uploaded to the ftp server. // username:password@locati on:tcpport/filename specifies the upload configuration file url on the ftp server. For example, ‘// user:123@192.168.0.1:8...

  • Page 191

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 183 9-8 copy this command is used to download the configuration file from the tftp server or ftp server and execute it or save it as the boot-up configuration file. This command is also used to execute the configuration stored in the nvram o...

  • Page 192

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 184 running-config specifies that the specified configuration will be executed immediately by using the increment method. The specified configuration will merge with the current configuration. The existing configuration will not be cleared b...

  • Page 193

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 185 example this example shows how to download the ‘config.Cfg’ file from the tftp server then save it and configure it to be the boot-up configuration file. Dxs-3600-32s#copy tftp: //10.0.0.66/config.Cfg bootup-config address of remote host...

  • Page 194

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 186 example this example shows how to download the ‘config.Cfg’ file from the ftp server then execute it immediately by using the increment method. Dxs-3600-32s#copy ftp: //user:123@10.0.0.66:80/config.Cfg running-config address of remote ho...

  • Page 195: Counter Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 187 counter commands 10-1 clear counters this command is used to clear counters for a specific port interface or all port interfaces. Clear counters [interface-id] parameters 10-2 show interfaces counters this command is used to display the ...

  • Page 196

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 188 10-3 show utilization this command is used to display the interface utilization. Show utilization ports example this example shows how to display counters of all interfaces. Dxs-3600-32s#show interfaces counters interface : 1/0/1 input r...

  • Page 197

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 189 example this example shows how to display port utilization. Dxs-3600-32s#show utilization ports port tx/sec rx/sec util ----- ---------- ---------- ---- 1/0/1 0 0 0 1/0/2 0 0 0 1/0/3 0 0 0 1/0/4 0 0 0 1/0/5 0 0 0 1/0/6 0 0 0 1/0/7 0 0 0 ...

  • Page 198: Cpu Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 190 cpu commands 11-1 show cpu this command is used to show the cpu utilization information. Show cpu parameters none. Default none. Command mode privileged exec mode. Command default level level: 15 usage guideline use this command to show ...

  • Page 199: Debug Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 191 debug commands 12-1 debug enable this command is used to set the debug state as enabled. Users can use no debug command to disable the debug state. Debug enable no debug 12-2 error-reboot enable this command is used to set the switch to ...

  • Page 200

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 192 12-3 copy error-log this command is used to copy error log information to a location filename through tftp. Copy error-log tftp [//location/filename] parameters 12-4 copy debug buffer this command is used to copy debug buffer information...

  • Page 202

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 194 12-7 clear error-log this command is used to clear error log information. Clear error-log 12-8 show error-reboot this command is used to show the state of the error-reboot option. Show error-reboot example this example shows how to show ...

  • Page 203

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 195 12-9 clear debug buffer this command is used to clear the debug buffer. Clear debug buffer 12-10 show debug buffer this command is used to show the information of the debug buffer. Show debug buffer [utilization] parameters usage guideli...

  • Page 204

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 196 12-11 show debug status this command is used to show the debug buffer’s status of the modules. Show debug status 12-12 show tech-support this command is used to show technical support information. Show tech-support example this example s...

  • Page 205

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 197 12-13 copy tech-support this command is used to copy technical support information to a location filename through tftp. Copy tech-support tftp //location/filename parameters example this example shows how to show the technical support in...

  • Page 206

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 198 12-14 debug show module_version this command is used to show the module version of the modules. Debug show module_version [module module_list>] parameters module specifies the module which version will be displayed. Module_list specifies...

  • Page 207: Dhcp Relay Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 199 dhcp relay commands 13-1 service dhcp this command is used to enable the dhcp relay feature. The no form of this command can disable the dhcp relay feature. Service dhcp no service dhcp 13-2 ip helper-address this command is used to add ...

  • Page 208

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 200 13-4 ip dhcp relay option60 this command is used to enable the dhcp relay option 60 function. The no form of this command is used to disable the dhcp relay option 60 function. Ip dhcp relay option60 no ip dhcp relay option60 13-5 ip dhcp...

  • Page 209

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 201 13-6 ip dhcp relay option60 default this command is used to add default relay servers, used by the dhcp relay option 60. The no form of this command deletes the option 60 default relay server. Ip dhcp relay option60 default relay ip-addr...

  • Page 211

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 203 13-9 ip dhcp relay option61 identifier this command is used to add a dhcp server ip address for a specific option 61. The no form of this command deletes the dhcp server ip address for that option 61. Ip dhcp relay option61 identifier {s...

  • Page 212

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 204 13-11 show ip dhcp relay option61 this command is used to show the entries of the dhcp relay option 61. Show ip dhcp relay option61 example this example shows how to add default relay servers to be used by the dhcp relay option 61. Dxs-3...

  • Page 213: Dhcp Server Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 205 dhcp server commands 14-1 bootfile this command is used to define the startup mapping file name of the dhcp client in the dhcp address pool configuration mode. The no form of this command can be used to remove the definition. Bootfile fi...

  • Page 215

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 207 14-4 default-router this command is used to define the default gateway of the dhcp client in the dhpc address pool configuration mode. The no form of this command can be used to delete the definition of the default gateway. Default-route...

  • Page 216

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 208 no dns-server parameters 14-6 domain-name this command is used to define the suffix domain name of the dhcp client in the dhpc address pool configuration mode. The no form of this command can be used to delete the suffix domain name. Dom...

  • Page 217

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 209 parameters 14-8 host this command is used to define the ip address and network mask of the dhcp client host in the dhcp address pool configuration mode. The no form of this command can be used to delete the definition of the ip address a...

  • Page 218

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 210 14-9 ip dhcp excluded-address this command is used to define some ip addresses and make the dhcp server not assign them to the dhcp client in the global configuration mode. The no form of this command can be used to cancel this definitio...

  • Page 219

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 211 14-11 ip dhcp ping timeout this command is used to configure the timeout that the dhcp server waits for response when it uses the ping operation to detect the address conflict in the global configuration mode. The no form of this command...

  • Page 220

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 212 14-13 lease this command is used to define the lease time of the ip address that the dhcp server assigns to the client in the dhcp address pool configuration mode. The no form of this command can be used to restore it to the default conf...

  • Page 221

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 213 parameters 14-15 netbios-node-type this command is used to define the node type of the master netbios of the microsoft dhcp client in the dhcp address configuration mode. The no form of this command can be used to delete the configuratio...

  • Page 222

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 214 14-16 network this command is used to define the network number and network mask of the dhcp address pool in the dhcp address pool configuration mode. The no form of this command can be used to delete the definition. Network net-number n...

  • Page 223

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 215 14-17 next-server this command is used to define the startup server that the dhcp client accesses during startup in the dhcp address configuration mode. The no form of this command can be used to delete the definition of the startup serv...

  • Page 224

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 216 show ip dhcp excluded-address [vrf vrf-name] parameters 14-20 show ip dhcp binding this command is used to show the binding condition of the dhcp address. Show ip dhcp binding [vrf vrf-name] [ip-address] parameters vrf vrf-name (optional...

  • Page 225

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 217 14-21 show ip dhcp conflict this command is used to show the conflict history record of dhcp server. Show ip dhcp conflict [vrf vrf-name] parameters example this example shows how to the result of the show ip dhcp binding command. Dxs-36...

  • Page 226

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 218 14-22 show ip dhcp pool this command is used to display information about the dynamic host configuration protocol (dhcp) address pools. Show ip dhcp pool [pool-name] parameters 14-23 show ip dhcp server this command is used to display th...

  • Page 227

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 219 14-24 vrf this command is used to associate the on-demand address pool with a vpn routing and forwarding instance (vrf) name. To remove the vrf name, use the no form of this command. Vrf vrf-name no vrf vrf-name parameters default none. ...

  • Page 228: Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 220 distance vector multicast routing protocol (dvmrp) commands 15-1 ip dvmrp this command is used to enable the distance vector multicast routing protocol (dvmrp) on an interface. To disable dvmrp on the interface, use the no form of this c...

  • Page 229

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 221 15-3 show ip dvmrp interface this command is used to display dvmrp interface information. Show ip dvmrp interface [ifname] parameters usage guideline for each source network reported, a route metric is associated with the route being rep...

  • Page 230

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 222 15-4 show ip dvmrp neighbor this command is used to display dvmrp neighbor information. Show ip dvmrp neighbor [ifname] parameters display parameters description interface specifies the interface name. Ip address the ip address of the in...

  • Page 231

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 223 15-5 show ip dvmrp route this command is used to display the dvmrp route info. Show ip dvmrp route [ipaddress mask] parameters generation id specify the generation id of the neighbor. This value is dynamically generated by the neighbor s...

  • Page 232

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 224.

  • Page 233

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 225 d-link license management system commands 16-1 install dlms activation_code this command is used to install an activation code on the switch. Install dlms activation_code ac_str parameters 16-2 show dlms license this command is used to d...

  • Page 234

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 226 example this example shows how to display the license information. The field descriptions are self-explanatory. The following example shows how to display the license information on the switch. Dxs-3600-32s#show dlms license device defau...

  • Page 235

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 227 domain name system (dns) commands 17-1 ip domain-lookup this command is used to enable the domain name look up for the switch itself's application. For example, to ping a domain name on the switch. Us the no form of this command to disab...

  • Page 236

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 228 17-3 ip host this command is used to configure the mapping of the host name and the ip address by manual. Use the no form of the command to remove the host list. Ip host [vrf ] host-name ip-address no ip host [vrf ] host-name ip-address ...

  • Page 237

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 229 show hosts [vrf ] parameters 17-6 ip dns server this command is used to control if the switch can use the domain name for other dns clients which are connected to it. If the dns server state is enabled, when it recevies a dns query, it w...

  • Page 239

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 231 xmas scan hackers use the tcp xmas scan to identify listening tcp ports. This scan uses a series of strangely configured tcp packets, which contain the urgent (urg), push (psh), and fin flags. Again, this type of scan can get through som...

  • Page 240

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 232 18-2 show defense this command is used to display attack defense information. Show-defense example this example shows how to disable the defense land attack. Dxs-3600-32s#configure terminal dxs-3600-32s(config)#no defense land enable suc...

  • Page 241

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 233 enhanced transmission selection (ets) commands 19-1 ets willing this command is used to enable the enhanced transmission selection (ets) willing mode for the data center bridging exchange protocol (dcbx) on a specified interface. Use the...

  • Page 243

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 235 - (optional) specifies a range of interfaces. No space before and after the hyphen. Recommend (optional) specifies to display the ets recommendation information of a given interface or all interfaces. Default none. Command mode exec mode...

  • Page 244

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 236 example this example shows how to display recommendation information for interface 1/1/1. Dxs-3600-32s#show ets interface gigabitethernet 1/1/1 recommend interface id: gigabitethernet 1/1/1 recommended tc setting: cos mapped coss schedul...

  • Page 245: File System Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 237 file system commands 20-1 dir this command is used to show the files in the current directory. Dir directory parameters 20-2 ls this command is used to show the files in the current directory. Ls directory parameters directory (optional)...

  • Page 247

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 239 20-5 rename this command is used to rename a specific file. Rename old_filename new_filename parameters 20-6 mkdir this command is used to create a directory. Mkdir directory parameters usage guideline change the parameter to the directo...

  • Page 248

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 240 20-7 rmdir this command is used to delete an empty directory. Rmdir directory parameters 20-8 rm this command is used to delete the specified file. Rm filename parameters 20-9 del this command is used to delete the specified file. Del fi...

  • Page 249

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 241 parameters 20-10 makefs this command is used to format the device that the file system is to be loaded or the device that is to be managed by the file system. Makefs dev devname fs fsname makefs fs fsname dev devname parameters 20-11 pwd...

  • Page 250

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 242 command mode privileged exec mode. Command default level level: 3 usage guideline this command shows the current working path. Example this example shows how to show the current working path. Dxs-3600-32s#pwd flash: dxs-3600-32s#.

  • Page 251

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 243 filter database (fdb) commands 21-1 mac-address-table aging-time this command is used to set the length of time that a dynamic entry remains in the mac address table. Use the no form of the command to set the time to default. Mac-address...

  • Page 252

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 244 21-3 mac-address-table static this command is used to add a static address to the mac address table. Use the no form of the command to remove a static mac address entry from the table. Mac-address-table static mac-add vlan vlan-id interf...

  • Page 253

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 245 21-4 mac-address-table filtering this command is used to add a filtering address to the mac address table. Use the no form of the command to remove a filtering mac address entry from the table. Mac-address-table filtering mac-add vlan vl...

  • Page 254

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 246 21-5 mac-address-table notification this command is used to enable and configure the mac address notification function. Use the no form of the command to disable the function or set the optional configuration to default. Mac-address-tabl...

  • Page 257

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 249 parameters dynamic (optional) displays dynamic mac address entries only. Static (optional) displays user creates static mac address entries and l3 interface mac address entries only. Filtering (optional) displays user creates filtering m...

  • Page 258

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 250 example this example shows how to display all the static mac address table entries. Dxs-3600-32s#show mac-address-table static vlan mac address type interface protocol ---- ----------------- ---------- ------------------------- -------- ...

  • Page 261

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 253 22-5 gvrp dynamic-vlan-creation this command is used to enable dynamic vlan creation, and use the no command to disable the dynamic vlan creation function. Gvrp dynamic-vlan-creation no gvrp dynamic-vlan-creation 22-6 forbidden vlan this...

  • Page 264

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 256 example this example shows how to display statistics for gvrp ports 1-2. Dxs-3600-32s#show gvrp statistics interface tengigabitethernet 1/0/1-1/0/2 interface joinempty joinin leaveempty leavein leaveall empty ----------------------------...

  • Page 266

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 258 23-3 ip igmp last-member-query-interval this command is used to configure the interval at which the switch sends igmp group-specific or group-source-specific (with igmp version 3) query messages, use the ip igmp last-member-query-interva...

  • Page 267

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 259 no ip igmp query-interval parameters 23-5 ip igmp query-max-response-time this command is used to configure the maximum response interval. Use the no form of this command to set the maximum response interval to the default value. Ip igmp...

  • Page 268

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 260 ip igmp robustness-variable number no ip igmp robustness-variable parameters 23-7 ip igmp version this command is used to set the version number of igmp to be used on the interface. Use the no form of this command to restore it to the de...

  • Page 269

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 261 23-8 ip igmp check-subscriber-source-network this command is used to configure the flag that determines whether or not to check the subscriber’s source ip when an igmp report or leave message is received. Use the no form of this command ...

  • Page 270

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 262 23-10 show ip igmp groups this command is used to show the groups directly connected to the device and the group information learnt from igmp. Example this example shows the information of all the interfaces. Dxs-3600-32s#show ip igmp in...

  • Page 272

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 264 example this example shows detailed group information on a specific interface:. Dxs-3600-32s#show ip igmp groups interface vlan1 detail igmp group detail information interface : vlan1 multicast group : 224.1.1.1 last reporter : 10.0.31.1...

  • Page 273

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 265 example this example shows detailed information of a specific group. Dxs-3600-32s#show ip igmp groups group 224.1.1.1 detail igmp group detail information interface : vlan1 multicast group : 224.1.1.1 last reporter : 10.0.31.1 ip querier...

  • Page 274: Igmp Snooping Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 266 igmp snooping commands 24-1 ip igmp snooping this command is used to enable the igmp snooping state. Use the no form of this command to disable the igmp snooping state. Ip igmp snooping no ip igmp snooping 24-2 ip igmp snooping fast-leav...

  • Page 275

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 267 24-3 ip igmp snooping mrouter this command is used to configure the specified interface(s) as the multicast router interface(s) or as forbidden to be multicast router interface(s) on the switch. Use the no form of this command to remove ...

  • Page 276

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 268 24-4 ip igmp snooping dyn-mr-aging-time this command is used to configure the aging out time for dynamic multicast router interface. To restore the default value, use the no form of this command. Ip igmp snooping dyn-mr-aging-time second...

  • Page 277

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 269 ip igmp snooping querier no ip igmp snooping querier 24-6 ip igmp snooping static-group this command is used to directly add an interface list or a port-group to a multicast group. Use the no form of this command to remove the setting. I...

  • Page 278

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 270 24-7 ip igmp snooping max-response-time this command is used to configure the max response time in igmp snooping. To restore the default value, use the no form of this command. Ip igmp snooping max-response-time seconds no ip igmp snoopi...

  • Page 279

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 271 24-8 ip igmp snooping query-interval this command is used to configure the interval between general queries sent by igmp snooping querier. To restore the default value, use the no form of this command. Ip igmp snooping query-interval sec...

  • Page 280

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 272 24-10 clear ip igmp snooping statistics this command is used to clear igmp snooping statistics counter on the switch. Clear ip igmp snooping statistics default by default, this value is 3. Command mode interface configuration mode. Comma...

  • Page 281

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 273 24-11 show ip igmp snooping this command is used to display the igmp snooping related configurations. Show ip igmp snooping [vlan vlan-id] parameters usage guideline this command is used to clear igmp snooping statistics counter. Example...

  • Page 282

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 274 24-12 show ip igmp snooping querier this command is used to display igmp snooping querier electing information. Show ip igmp snooping querier [vlan vlan-id] parameters display parameters description igmp snooping global state specify igm...

  • Page 285

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 277 24-15 show ip igmp snooping mrouter this command is used to display igmp snooping multicast router interface information. Show ip igmp snooping mrouter [vlan vlan-id] parameters example this example shows how to display the igmp snooping...

  • Page 286

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 278 24-16 show ip igmp snooping forwarding-table this command is used to display igmp snooping forwarding information. Show ip igmp snooping forwarding-table [vlan vlan-id] parameters usage guideline this command is used to display igmp snoo...

  • Page 287

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 279 24-17 show ip igmp snooping statistics this command is used to display igmp snooping statistics counter information. Show ip igmp snooping statistics [vlan vlan-id] parameters example this example shows how to display all igmp snooping f...

  • Page 288

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 280 example this example shows how to display igmp snooping statistics counter information on the whole switch, and it will only display the igmp snooping enabled vlan interface. Dxs-3600-32s#show ip igmp snooping statistics vlan #1 --------...

  • Page 289: Interface Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 281 interface commands 25-1 interface out-band this command is used to select the out-band interface, and enter the interface configuration mode. Interface out-band int> parameters 25-2 interface loopback this command is used to create a loo...

  • Page 290

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 282 no shutdown 25-4 show interface out-band this command is used to display the out band interface. Show interface out-band int> parameters 25-5 show interface loopback this command is used to display all the ip interfaces. Show interface l...

  • Page 291

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 283 default none. Command mode exec mode. Command default level level: 3 usage guideline use this command to display the loopback interface. Example this example shows how to display the loopback interface. Dxs-3600-32s#show interface loopba...

  • Page 292: Ip Access List Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 284 ip access list commands 26-1 ip standard access-list this command is used to enter the access list configuration mode and define a standard ip access list. Use the no form of this command to remove a standard ip access list. Ip standard ...

  • Page 293

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 285 26-3 permit this command is used to set the permit rules of standard ip access list. Use the no form of this command to remove the permit rules. Permit network-address no permit network-address parameters 26-4 show ip standard access-lis...

  • Page 294

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 286 example this example shows the content of standard ip access list 'ips'. Dxs-3600-32s#show ip standard access-list ips ip standard access list: ips total entries number : 2 permit 120.2.0.0/16 deny 125.1.2.2/20 total access list number :...

  • Page 295: Ip Address Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 287 ip address commands 27-1 ip address this command is used to set the primary or secondary ip address for an interface. Use no command to remove the ip address. Ip address ip-address net-mask [secondary] no ip address ip-address net-mask [...

  • Page 296

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 288 27-3 ip directed-broadcast this command is used to enable forwarding of ip directed broadcasts on an interface where the broadcast becomes a physical broadcast. Use no command to disable forwarding of ip directed broadcasts on an interfa...

  • Page 297

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 289 27-5 show ip interface this command is used to display all the ip interfaces. Show ip interface [interface-name] parameters usage guideline this command set or remove the default gateway address for the out-band interface. This command i...

  • Page 298: Ip Prefix List Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 290 ip prefix list commands 28-1 ip prefix-list this command is used to create an ip prefix list or add a rule for an ip prefix list. Use the no form of this command to remove an ip prefix list or remove a rule for an ip prefix list. Ip pref...

  • Page 299

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 291 28-2 ip prefix-list description this command is used to add the text description to a prefix list. Use the no form of this command to delete the description. Ip prefix-list prefix-list-name description desc no ip prefix-list prefix-list-...

  • Page 301

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 293.

  • Page 303

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 295 29-2 ip multicast-routing this command is used to enable global ip multicast routing. The no form of the command disables global ip multicast routing. Ip multicast-routing no ip multicast-routing 29-3 show ip mroute this command is used ...

  • Page 304

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 296 usage guideline this command is used to display the multicast routing entries learned on the switch or the multicast static routes created on the switch. You can specify the parameter to display the information that you concerning. If no...

  • Page 305

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 297 29-4 show ip rpf this command is used to show the rpf information for the specified source address. Show ip rpf source-address parameters example this example shows how to display ip multicast routing information for group source part (2...

  • Page 306

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 298 29-5 show ip multicast interface this command is used to display the basic multicast information of an interface. Show ip multicast interface [ifname] usage guideline this command is used to display the rpf information of the specified s...

  • Page 307

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 299 parameters 29-6 show ip multicast-routing this command is used to display ip multicast routing global state. Show ip multicast-routing ifname specifies the interface name. Default none. Command mode privileged exec mode. Command default ...

  • Page 308

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 300 example this example shows how to display ip multicast routing information. Dxs-3600-32s#show ip multicast-routing ip multicast routing state: disabled dxs-3600-32s# display parameters description ip multicast routing state this state ca...

  • Page 310

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 302 30-3 speed this command is used to set the speed at which the terminal transmits packets, execute the speed speed command in the line configuration mode. To restore the speed to its default value, run the no speed command. Speed speed no...

  • Page 312

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 304 31-3 lacp system-priority this command is used to set the lacp system priority. The no form of it restores it to the default. Lacp system-priority system-priority no lacp system-priority parameters 31-4 lacp timeout this command is used ...

  • Page 313

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 305 31-5 port-group this command is used to assign a physical interface to be a member port of an aggregate port. Use the no form of the command to remove the membership from the aggregate port. Port-group port-group-number [static] no port-...

  • Page 315

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 307 default none. Command mode exec mode. Command default level level: 15 usage guideline none. Example this example shows how to display lacp summary. Dxs-3600-32s#show lacp summary flags:s - port is perform slow timeout f - port is perform...

  • Page 316

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 308 port state state variables for the port, encoded as individual bits within a single octet with these meanings: • bit0: lacp_activity • bit1: lacp_timeout • bit2: aggregation • bit3: synchronization • bit4: collecting • bit5: distributing...

  • Page 317

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 309 link layer discovery protocol (lldp) commands 32-1 lldp run this command is used to enable the link layer discovery protocol (lldp) globally. Use the no form of this command to return to the default settings. Lldp run no lldp run 32-2 ll...

  • Page 318

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 310 32-3 lldp message-tx-interval this command is used to set the lldpdus transmission interval on the switch. Use the no form of this command to return to the default settings. Lldp message-tx-interval seconds no lldp message-tx-interval pa...

  • Page 319

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 311 32-5 lldp tx-delay this command is used to set the minimum time (delay-interval), any lldp port will delay advertising successive lldp advertisements due to a change in lldp mib content. The tx-delay defines the minimum interval between ...

  • Page 320

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 312 lldp reinit-delay seconds no lldp reinit-delay parameters 32-7 lldp notification-interval this command is used to set the the timer of the notification interval for sending notifications to configured snmp trap receiver(s). Use the no fo...

  • Page 321

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 313 32-8 lldp notification this command is used to enable the snmp trap notification of lldp data changes detected on advertisements received from neighbor devices on each physical interfaces. Use the no form of this command to return to the...

  • Page 322

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 314 32-10 lldp transmit this command is used to enable the lldp advertise (transmit) capability. Use the no form of this command to return to the default settings. Lldp transmit no lldp transmit 32-11 lldp receive this command is used to ena...

  • Page 323

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 315 32-12 lldp tlv-select this command is used to specify which optional type-length-value settings (tlvs) in the 802.1ab basic management set will be transmitted and encapsulated in the lldpdus and sent to neighbor devices. To disable trans...

  • Page 324

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 316 32-13 lldp dot1-tlv-select this command is used to specify which optional type-length-value settings (tlvs) in the ieee 802.1 organizationally specific tlv set will be transmitted and encapsulated in the lldpdus and sent to neighbor devi...

  • Page 325

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 317 usage guideline if the optional tlvs advertisement state enabled, they will be encapsulated in lldpdu and sent to other devices. The protocol identity tlv optional data type indicates whether the corresponding local system's protocol ide...

  • Page 326

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 318 32-14 lldp dot3-tlv-select this command is used to specify which optional type-length-value setting (tlvs), in the ieee 802.3 organizationally specific tlv set, will be transmitted and encapsulated in the lldpdus and sent to neighbor dev...

  • Page 327

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 319 32-15 show lldp this command is used to display the switch’s general lldp configuration status. Show lldp 32-16 show lldp management-address this command is used to display the lldp management address information. Show lldp management-ad...

  • Page 330

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 322 example this example shows how to display outbound lldp advertisements for an interface in detailed mode. Dxs-3600-32s#show lldp local interface tengigabitethernet 1/0/1 detail interface id : 1/0/1 ---------------------------------------...

  • Page 332

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 324 example this example shows how to display outbound lldp advertisements for an interface in detailed mode. Dxs-3600-32s#show lldp remote interface tengigabitethernet 1/0/1 detail remote entities count : 1 interface id : 1/0/1 ------------...

  • Page 333

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 325 32-20 show lldp statistic this command is used to display the system global lldp statistics information. Show lldp statistic 32-21 show lldp statistic interface this command is used to display each physical interface lldp statistics info...

  • Page 334

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 326 command default level level: 3 usage guideline the each physical interface lldp statistics command displays each physical interface lldp statistics example this example shows how to display statistics information of an interface. Dxs-360...

  • Page 335: Lldp-Dcbx Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 327 lldp-dcbx commands 33-1 lldp-dcbx run this command is used to to enable the data center bridging exchange protocol (dcbx) on each physical interface. Use the no form of this command to return to the default settings. Lldp-dcbx run no lld...

  • Page 336

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 328 33-3 show lldp-dcbx interface this command is used to display the lldp dcbx of each physical interface configuration for advertisement options. Show lldp-dcbx interface interface-id parameters 33-4 show lldp-dcbx local interface this com...

  • Page 337

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 329 usage guideline this command displays each physical interface’s information currently available for populating outbound lldp dcbx advertisements. Example this example shows how to display a specific physical interface's local information...

  • Page 338

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 330 33-5 show lldp-dcbx remote interface this command is used to display the physical interface’s information currently learned from the neighbor. Show lldp-dcbx remote interface interface-id parameters pfc basic configuration willing : enab...

  • Page 339

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 331 ets configuration traffic class bandwidth tc0 : 0 tc1 : 50 tc2 : 0 tc3 : 0 tc4 : 50 tc5 : 0 tc6 : 0 tc7 : 0 ets configuration traffic selection algorithm tc0 : tsavendorspecific tc1 : tsavendorspecific tc2 : tsavendorspecific tc3 : tsave...

  • Page 340: Lldp-Med Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 332 lldp-med commands 34-1 lldp-med fast-start-repeat-count this command is used to set the fast start repeat count on the switch. Use the no form of this command to return to the default settings. Lldp-med fast-start-repeat-count value no l...

  • Page 344

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 336 default none. Command mode user exec mode. Command default level level: 3 usage guideline used to display the lldp-med information learned from the neighbor. Example this example shows how to display the lldp-med information learned from...

  • Page 345: Memory Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 337 memory commands 35-1 show memory this command is used to display the current memory usage information. Show memory parameters none. Default none. Command mode privileged exec mode. Command default level level: 15 usage guideline use this...

  • Page 346: Mirror Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 338 mirror commands 36-1 monitor session this command is used to monitor a session, create a mirror session, and to specify the destination port or source port. The no form of the command is used to delete the whole session or delete the sou...

  • Page 347

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 339 36-2 no monitor session all this command is used to delete all the monitor sessions directly. No monitor session all number of mirror ports are 4 mtps, mtps port can be same or different. For a mirrored packet, do no vlan membership chec...

  • Page 348

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 340 36-3 show monitor this command is used to display monitor sessions. Show monitor [session session_number] parameters session_number specifies the mirror session number to display. Default all the monitor sessions are displayed. Command m...

  • Page 349

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 341.

  • Page 350

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 342 multicast filter mode commands 37-1 multicast filtering-mode this command is used to configure multicast packets filtering mode for vlans. To restore the default configuration, use no form of this command. Multicast filtering-mode {forwa...

  • Page 351

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 343 command mode privileged exec mode. Command default level level: 3 usage guideline this command is used to display information about the multicast filter mode configuration. Example this example shows how to display multicast filter mode ...

  • Page 352

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 344 multiprotocol label switching (mpls) commands 38-1 mpls ip (global configuration) this command is used to enable the mpls forward globally. Use no mpls ip command in global configuration mode to disable mpls forward globally. Mpls ip no ...

  • Page 353

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 345 38-4 mpls static ftn this command is used to add a static ftn entry. Use no mpls static ftn command to remove the previous configured static ftn. Mpls static ftn network-prefix/prefix-length out-label label-value nexthop ip-address no mp...

  • Page 355

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 347 38-7 mpls label protocol ldp (global configuration) this command is used to enable ldp globally. Use no mpls label protocol in global configuration mode to disable ldp globally. Mpls label protocol ldp no mpls label protocol 38-8 snmp-se...

  • Page 356

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 348 38-9 mpls label protocol ldp (interface configuration) this command is used to enable ldp on this interface. Use the no mpls label protocol command in interface configuration mode to disable ldp on this interface. Mpls label protocol ldp...

  • Page 357

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 349 38-11 mpls ldp hello-interval this command is used to configure the ldp link hello interval time for the interface. Use the no form of this command to restore the default value. Mpls ldp hello- interval seconds no mpls ldp hello- interva...

  • Page 358

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 350 38-13 mpls ldp targeted-peer this command is used to create a ldp targeted peer. Use the no form of this command to remove the previous configured ldp targeted peer. Mpls ldp targeted-peer ip-address no mpls ldp targeted-peer ip-address ...

  • Page 359

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 351 38-15 ldp router-id this command is used to set the lsr id of the ldp. Use no ldp router-id command to restore the lsr id to default value. Ldp router-id ip-address no ldp router-id parameters 38-16 transport-address this command is used...

  • Page 360

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 352 parameters 38-17 backoff maximum this command is used to configure the maximum back-off delay time. Use the no form of this command to restore the default value. Backoff maximum seconds no backoff maximum parameters interface specifies t...

  • Page 361

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 353 38-18 keepalive-holdtime this command is used to configure the keep-alive hold-time for ldp sessions. Use the no form of this command to restore the default value. Keepalive-holdtime seconds no keepalive-holdtime parameters 38-19 label-r...

  • Page 364

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 356 38-23 max-hop-count this command is used to configure the maximum hop count allowed for loop detection. Use the no form of this command to restore the default value. Max-hop-count value no max-hop-count parameters 38-24 max-path-vector t...

  • Page 365

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 357 38-25 explicit-null this command is used to advertise an explicit null label in situations where it would normally advertise an implicit null label. Use the no form of this command to restore the default value. Explicit-null no explicit-...

  • Page 366

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 358 38-27 neighbor password this command is used to configure the ldp peer password. Use the no form of this command to restore the default value. Neighbor ip-address password password no neighbor ip-address password parameters 38-28 show mp...

  • Page 367

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 359 38-29 show mpls interface this command is used to display mpls enabled interfaces. Show mpls interface [interface-id] parameters 38-30 show mpls forwarding-table this command is used to display the mpls label forwarding path information....

  • Page 368

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 360 ftn specifies to only display ftn entries. Ilm specifies to only display ilm entries. Detail specifies to display detailed mpls label forwarding path information. Default none. Command mode exec mode. Command default level level: 3. Usag...

  • Page 369

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 361 38-31 show mpls ldp parameter this command is used to display ldp global information. Show mpls ldp parameter lsp: 6 type: egress status: up fec: vc11/192.1.1.1 owner: ldp in label: 200 out label: pop total entries: 6 dxs-3600-32s# examp...

  • Page 370

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 362 38-32 show mpls ldp interface this command is used to display ldp interface information. Show mpls ldp interface [interface-id] parameters example this example shows how to display ldp global information. Dxs-3600-32s#show mpls ldp param...

  • Page 371

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 363 38-33 show mpls ldp targeted-peer this command is used to display previously configured targeted peer information. Show mpls ldp targeted-peer [ip-address] parameters 38-34 show mpls ldp discovery this command is used to display ldp peer...

  • Page 372

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 364 show mpls ldp discovery 38-35 show mpls ldp neighbor this command is used to display ldp neighbor information. Show mpls ldp neighbor [ip-address] parameters parameters none. Default none. Command mode exec mode. Command default level le...

  • Page 374

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 366 38-37 show mpls ldp bindings this command is used to display all ldp label binding information. Show mpls ldp bindings example this example shows how to display all ldp session information. Dxs-3600-32s#show mpls ldp session peer status ...

  • Page 375

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 367 38-38 show mpls ldp statistic this command is used to display ldp global statistic information. Show mpls ldp statistic default none. Command mode exec mode. Command default level level: 3. Usage guideline this command is used to display...

  • Page 376

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 368 38-39 show mpls ldp neighbor password this command is used to display the ldp neighbor password. Show mpls ldp neighbor password 38-40 ping lsp this command is used to check the connectivity of the lsp for a specified fec. Ping lsp netwo...

  • Page 377

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 369 38-41 traceroute lsp this command is used to initiate hop-by-hop fault localization as well as path tracing for lsp of a specified fec. Traceroute lsp network-prefix/prefix-length [timeout seconds] parameters example this example shows h...

  • Page 379

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 371 38-43 show lsp trigger this command is used to display lsp trigger filter rule(s). Show lsp trigger [sn] parameters 38-44 mpls qos policy this command is used to enter the mpls qos configuration mode. If the policy doesn’t exist, a new p...

  • Page 380

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 372 38-45 trust-exp this command is used to configure to trust the incoming label’s topmost exp as priority. Use the no trust-exp command to disable the trust. Trust-exp no trust-exp 38-46 class-map this command is used to configure class ma...

  • Page 381

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 373 default inbound mapping: exp 0 1 2 3 4 5 6 7 priority 2 0 1 3 4 5 6 7 outbound mapping: no setting. Command mode mpls qos configuration mode. Command default level level: 15..

  • Page 382

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 374 usage guideline use the class-map inbound command to set the mapping from exp to have priority for incoming packets. The inbound mapping takes effect only when trust-exp is enabled. If inbound mapping exists, it will be replaced by the l...

  • Page 383

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 375 38-47 match this command is used to apply the policy to fecs. Use the no match command to remove the setting. Match {ip network-prefix/prefix-length} no match [ip network-prefix/prefix-length] parameters 38-48 show mpls qos this command ...

  • Page 384

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 376 command default level level: 3. Usage guideline use the show mpls qos policy command to display the mpls qos policy settings. Example this example shows how to display all mpls qos settings. Dxs-3600-32s#show mpls qos mpls qos policy: po...

  • Page 386

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 378 default the default probe number is 1, timeout is 5 seconds and maximum ttl is 30. Command mode privileged mode. Command default level level: 1 usage guideline this command is used to trace the routed path between the switch and a destin...

  • Page 387

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 379 open shortest path first (ospf) version 2 commands 40-1 area this command is used to create an ospf area. To remove an area, use the no form of this command. Area area-id no area area-id parameters 40-2 area default-cost this command is ...

  • Page 388

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 380 40-3 area nssa this command is used to assign an area as a nssa area. Use the no command to remove the nssa related settings associated with the area. Area area-id nssa [no-summary] [translate] no area area-id nssa [no-summary] [translat...

  • Page 390

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 382 40-5 area stub this command is used to assign an area as a stub area. Use the no command to remove the stub related settings associated with the area. Area area-id stub [no-summary] no area area-id stub [no-summary] parameters 40-6 area ...

  • Page 391

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 383 parameters area-id specifies the identifier of the area to establish the virtual link. Router-id specifies the router id of the virtual link neighbor. Authentication (optional) specifies authentication type. If the authentication type is...

  • Page 392

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 384 40-7 clear ip ospf process this command is used to restart the ospf process. Clear ip ospf process [vrf vrf-name] parameters 40-8 default-information originate this command is used to generate a default external route (as external lsa) i...

  • Page 393

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 385 40-9 default-metric this command is used to set the default metric value of ospf redistributed routes. Use the no command to restore to the default value. Default-metric metric no default-metric parameters 40-10 route-preference ospf thi...

  • Page 394

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 386 40-11 distribute-list in this command is used to configure lsa filtering. Use the no command to restore to the default value. Distribute-list list-name in [ipif_name] no distribute-list list-name in [ipif_name] parameters external-1 valu...

  • Page 396

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 388 40-13 ip ospf authentication-key this command is used to configure the plain text authentication key for an ospf interface. Use the no command to delete the plain text authentication key. Ip ospf authentication-key password no ip ospf au...

  • Page 397

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 389 40-15 ip ospf dead-interval this command is used to configure the interval during which at least one hello packet form a neighbor must be received before it is declared dead. Use the no command to restore it to the default value. Ip ospf...

  • Page 398

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 390 ip ospf hello-interval seconds no ip ospf hello-interval parameters 40-17 ip ospf message-digest-key this command is used to configure the md5 digest key for ospf interface. Use the no command to delete the md5 key. Ip ospf message-diges...

  • Page 399

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 391 40-18 ip ospf priority this command is used to configure the router priority that is used to determine the designated router for the network. Use the no command to restore it to the default value. Ip ospf priority priority no ip ospf pri...

  • Page 400

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 392 40-19 network area this command is used to enable ospf routing with a specified area id on interfaces with ip addresses that match or belong to the specified network address. Use the no command to remove the configuration. Network ipaddr...

  • Page 402

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 394 40-22 router ospf this command is used to enable ospf and enter the router configuration mode. Use the no form of this command to disable ospf. Router ospf [vrf vrf-name] no router ospf [vrf vrf-name] parameters default by default route ...

  • Page 403

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 395 40-23 router-id this command is used to configure the router id. Use the no command to restore to the default value. Router-id router-id no router-id parameters usage guideline use this command to enter router configuration mode to confi...

  • Page 404

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 396 40-24 show ip ospf this command is used to use this command to show general information about ospf. Show ip ospf [vrf vrf-name] parameters example this example shows how to restore the router-id to auto-select. Dxs-3600-32s#configure ter...

  • Page 405

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 397 example this example shows how to check ospf settings. Dxs-3600-32s#show ip ospf ospf router id : 10.90.90.90 state : disabled default information originate: state : enabled always : on metric : 10 ospf interface settings interface ip ad...

  • Page 406

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 398 stub import summary lsa whether to prohibit summary routes advertised into the area. It is only for stub or nssa area. It is specified with the command area stub or area nssa. Stub default cost the cost for the default summary route used...

  • Page 407

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 399 40-25 show ip ospf area this command is used to show general information about ospf areas. Show ip ospf area [area-id] [vrf vrf-name] parameters example this example show how to check the ospf settings in the vrf vpn-a. Dxs-3600-32s#show...

  • Page 408

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 400 usage guideline this command is used to show ospf areas information. When the area id is specified, the detail information about this area will be displayed. Example this example shows how to check ospf area settings. Dxs-3600-32s#show i...

  • Page 410

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 402 example this example shows detailed information of lsas in area 0.0.0.0. Dxs-3600-32s#show ip ospf 0.0.0.0 database area id: 0.0.0.0 ls type: router link link state id: 1.1.1.1/0 advertising router: 1.1.1.1 link state age: 1462 checksum:...

  • Page 411

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 403 40-27 show ip ospf interface this command is used to display interface information for ospf. Show ip ospf interface [ipif_name] [vrf vrf-name] parameters ipif_name (optional) specifies the interface name to display the ospf information. ...

  • Page 413

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 405 40-29 show ip ospf virtual-link this command is used to show information about ospf virtual links. Show ip ospf virtual-link [area-id neighbor-id] [vrf vrf-name] parameters example this example shows detailed information about neighbor w...

  • Page 414

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 406 40-30 show ip ospf virtual-neighbor this command is used to display information on ospf neighbors built on virtual links. Show ip ospf virtual-neighbor [area-id neighbor-id] [vrf vrf-name] parameters hello interval the interval between h...

  • Page 415

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 407 40-31 debug ip ospf this command is used to turn on ospf debug function. Use the no form of this command to turn off ospf debug function. Debug ip ospf no debug ip ospf 40-32 debug ip ospf neighbor this command is used to turn on the osp...

  • Page 416

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 408 40-34 debug ip ospf lsa-originating this command is used to turn on the ospf lsa originating debug switch. Use the no form of the command to turn off the ospf lsa originating debug switch. Debug ip ospf lsa-originating no debug ip ospf l...

  • Page 417

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 409 40-36 debug ip ospf packet-receiving this command is used to turn on the ospf packet receiving debug switch. Use the no form of the command to turn off the ospf packet receiving debug switch. Debug ip ospf packet-receiving no debug ip os...

  • Page 418

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 410 40-38 debug ip ospf spf this command is used to turn on the ospf spf calculation debug switch. Use the no form of the command to turn off the ospf spf calculation debug switch. Debug ip ospf spf no debug ip ospf spf 40-39 debug ip ospf t...

  • Page 419

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 411 40-40 debug ip ospf virtual-link this command is used to turn on the ospf virtual link debug switch. Use the no form of the command to turn off the ospf virtual link debug switch. Debug ip ospf virtual-link no debug ip ospf virtual-link ...

  • Page 420

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 412 40-42 debug ip ospf redistribution this command is used to turn on the ospf redistribution debug switch. Use the no form of the command to turn off the ospf redistribution debug switch. Debug ip ospf redistribution no debug ip ospf redis...

  • Page 423

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 415 debug ip ospf show request-list 40-47 debug ip ospf show redistribution this command is used to display the current internal ospf redistribution list. Debug ip ospf show redistribution parameters none. Default none. Command mode privileg...

  • Page 424

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 416 40-48 debug ip ospf show summary-list this command is used to display the current internal ospf summary list. Debug ip ospf show summary-list 40-49 debug ip ospf log this command is used to turn on the ospf debug log function. Use the no...

  • Page 425: Password Recovery Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 417 password recovery commands the first two commands, listed in this chapter, are only available when the user enters the password recovery mode. For more information about how to access the password recovery mode, see “appendix a - passwor...

  • Page 426

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 418 41-3 password-recover this command is used to enable the password recover option. The no form of this command is usd to disable this option. Password-recover no password-recover 41-4 show password-recover this command is used to display ...

  • Page 427: Peripheral Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 419 peripheral commands 42-1 show system-info this command is used to show system information. Show system-info 42-2 show device-status this command is used to show the device status. Show device-status parameters none. Default none. Command...

  • Page 428

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 420 42-3 logging-server enable device this command is used to enable the sending of log packets about peripheral devices. Use the no command to disable the sending of log packets. Logging-server enable device no logging-server enable device ...

  • Page 429: Port Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 421 port commands 43-1 interface this command is used to enter the interface configure mode. Interface {tengigabitethernet port>} interface range {tengigabitethernet portlist>} parameters 43-2 medium-type this command is used to specify the ...

  • Page 433

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 425 parameters 43-9 snmp trap link-status this command is used to specify the snmp trap-link status. Snmp trap link-status no snmp trap link-status 43-10 show interface this command is used to display interface information. Show interface [{...

  • Page 434

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 426 43-11 show module-info this command is used to dispay hot swapping expansion module information. Show module-info status specfies the display the interface status. Switchport specifies to display layer 2 interface information. Default no...

  • Page 436: Port Security Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 428 port security commands 44-1 switchport port-security this command is used to configure port security and the way to deal with violation of the interface. Use the no form of the command to disable the port security or recover it to the de...

  • Page 437

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 429 44-2 switchport port-security aging this command is used to set the aging time for all secure addresses on an interface. In this way, you can make the switch automatically add or delete the secure addresses on the interface. Use the no f...

  • Page 438

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 430 44-3 switchport port-security mac-address this command is used to configure the secure address table. Use the no form of the command to delete the configured address or sticky address of this interface. Switchport port-security [{mac-add...

  • Page 439

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 431 command default level level 15 for creating configured addresses and sticky addresses and enable sticky learning and level 8 for configuring the maximum. Usage guideline the first command is used to create secure mac address, sticky mac ...

  • Page 441

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 433 parameters 44-5 show port-security this command is used to show the port security settings. Show port-security [address] [interface interface-id>] parameters all specifies to delete all secure mac addresses. Configured specifies to delet...

  • Page 442

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 434 usage guideline this command shows all the port security configurations, secure addresses and the way to deal with violation if no parameter is configured. When you enter the command without keywords, the output includes the administrati...

  • Page 443

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 435 example this example shows how to display all secure mac addresses in the system. Dxs-3600-32s#show port-security address vlan mac address type ports remaining time (mins) ---- ----------------- ---------- --------- -------------- 1 00d0...

  • Page 444

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 436 priority-based flow control (pfc) commands 45-1 clear priority-flow-control counters this command is used to clear the priority-based flow control (pfc) counters of specified interface(s). Clear priority-flow-control counters [interface-...

  • Page 446

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 438 example this example shows how to display priority-based flow control of an interface. Dxs-3600-32s#show interface priority-flow-control interface pfc admin pfc on oper pfc on will- rx pfc tx pfc id cap. Priorities priorities ing frame(s...

  • Page 448

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 440 46-3 route-preference static this command is used to set the preference of the static route. Use no form of this command to restore to the default setting. Route-preference [vrf vrf-name] static value no route-preference [vrf vrf-name] s...

  • Page 449

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 441 46-4 ip mtu this command is used to set the maximum transmission unit (mtu) size of ip packets sent on an interface. Use the no form of this command to restore to the default setting. Ip mtu bytes no ip mtu parameters 46-5 ip ecmp load-b...

  • Page 450

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 442 46-6 ip route this command is used to add a static route entry. Use no form of this command to remove a static route entry. Primary and backup are mutually exclusive. Users can select only one when creating a new route. If user sets neit...

  • Page 451

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 443 command default level level: 8 usage guideline when the value of network and net-mask are both 0.0.0.0, it means to create a static default route. Use the command with keyword primary or backup means the newly created route is a floating...

  • Page 453

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 445 46-8 show ip ecmp load-balance this command is used to show the load-balancing algorithm settings. Example this example shows how to check the route preference of ospf route. Dxs-3600-32s#show ip route-preference ospf route preference se...

  • Page 455

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 447 example this example shows how to check the ip routing table. Dxs-3600-32s#show ip route routing table ip address/netmask gateway interface cost protocol ------------------ --------------- ------------ -------- -------- 20.1.1.0/24 10.1....

  • Page 456

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 448 example this example shows how to check the vrf vpn-a’s ip routing table. Dxs-3600-32s#show ip route routing table ( vrf: vpn-a ) ip address/netmask gateway interface cost protocol ------------------ --------------- ------------ --------...

  • Page 458

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 450 47-3 ip pim join-prune-interval this command is used to configure the interval of protocol independent multicast (pim) router join/prune messages. To return default, use the no form of this command. Ip pim join-prune-interval seconds no ...

  • Page 459

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 451 47-4 ip pim dr-priority this command is used to configure the priority for which a switch is elected as the designated router (dr). To return default, use the no form of this command. Ip pim dr-priority priority no ip pim dr-priority par...

  • Page 460

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 452 no ip pim register-suppression parameters 47-6 ip pim rp-address this command is used to create a static rp in pim-sm. To delete the static rp entry, use the no form of this command. Ip pim rp-address rp-address [access_list] no ip pim r...

  • Page 461

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 453 47-7 ip pim rp-candidate this command is used to configure the router to advertise itself as a protocol independent multicast (pim) version 2 candidate rendezvous point (rp) to the bootstrap router (bsr). To return default, use the no fo...

  • Page 462

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 454 0 specifies the prefix count value of the wildcard address (224.0.0.0/24) to be set to 0 in pim c-rp-adv message. 1 specifies that the wildcard prefix count value will be set to 1 in pim c-rp-adv message. Default no candidate rp is confi...

  • Page 464

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 456 47-10 ip pim bsr-candidate this command is used to enable the candidate bootstrap function of the interface or set the hash mask length of calculating the property rp. To return default, use no form of this command. Ip pim bsr-candidate ...

  • Page 465

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 457 47-11 ip pim old-register-checksum this command is used to specify for which rp, the switch should calculate checksum include the data portion or not when transmitting and receiving register messages. To restore the default setting, use ...

  • Page 467

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 459 47-14 show ip pim neighbor this command is used to display pim neighbor information. Show ip pim neighbor [ifname] parameters usage guideline this command displays pim-dm configuration information. Example this example shows how to displ...

  • Page 468

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 460 47-15 show ip pim sparse-mode bsr-router this command is used to display pim-sm bootstrap router information. Show ip pim sparse-mode bsr-router example this example displays all the interface’s neighbor information. Dxs-3600-32s#show ip...

  • Page 469

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 461 47-16 show ip pim sparse-mode interface this command is used to display pim-sm interface information. Show ip pim sparse-mode interface [ifname [detail]] parameters bsr priority priority as configured in the ip pim bsr-candidate command....

  • Page 470

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 462 47-17 show ip pim sparse-mode rp mapping this command is used to display rp mapping information. Show ip pim sparse-mode rp mapping example this example shows detailed information about the pim interface ‘vlan1’. Dxs-3600-32s#show ip pim...

  • Page 471

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 463 47-18 show ip pim sparse-mode rp-hash this command is used to display which rendezvous point is being selected for a specified group. Show ip pim sparse-mode rp-hash group-address parameters example this example displays pim-sm rp mappin...

  • Page 472

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 464 47-19 show ip pim this command is used to display pim global information. Show ip pim example this example shows pim-sm rp information for 229.1.3.1. Dxs-3600-32s#show ip pim sparse-mode rp-hash 229.1.3.1 rp: 10.2.0.2, via bootstrap upti...

  • Page 473

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 465 47-20 debug ip pim ssm this command is used to enable the pim ssm debug function. To disable this debug function, use no form of this command. Debug ip pim ssm no debug ip pim ssm register suppression time value in seconds. To configure ...

  • Page 474

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 466 example following debug trace message will be output when switch receives igmpv3 report with group record type mode_is_exclude referring to ssm group “232.0.0.0” from source ip “12.34.3.3” on interface “vlan1” pim_ssm, 20 dec 2010 10:52:...

  • Page 475

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 467 quality of service (qos) commands 48-1 class this command is used to specify a class map to be associated with a traffic policy and then enter into policy-map class configuration mode. Use the no form of this command to remove the specif...

  • Page 477

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 469 48-4 mls qos cos this command is used to define the default class of service (cos) value of a port. Use the no form of this command to return to the default setting. Mls qos cos default-cos no mls qos cos parameters 48-5 mls qos map dscp...

  • Page 479

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 471 parameters 48-8 police sr-tcm this command is used to configure traffic policing using the single rate in the policy-map class configuration mode. Remove the traffic policing from the switch configuration, use the no police command. Poli...

  • Page 480

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 472 action specifies the action to take on packets describe following: drop: drops packet. Set-dscp-transmit new-dscp: sets the ip differentiated services code points(dscp) value and transmits the packet with the new dscp value setting. Set-...

  • Page 481

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 473 48-9 police tr-tcm cir this command is used to configure traffic policing using two rates in policy-map configuration mode. Remove traffic policing from the configuration, use the no police command. Police tr-tcm cir cir [bc cbs] pir pir...

  • Page 482

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 474 48-10 police rate this command is used to define a policer for classified traffic. A policer defines a maximum permissible rate of transmission, a maximum burst size for transmissions, and an action to take if either maximum is exceeded....

  • Page 483

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 475 48-11 policy-map this command is used to create or modify a policy map that can be attached to multiple interfaces and to enter policy- map configuration mode. To remove a existing policy map, use the no form of this command. Policy-map ...

  • Page 484

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 476 48-12 priority-queue cos-map this command is used to define a class of service (cos) to queue maps in the global configuration mode. To restore to the default setting, use the no form of this command. Priority-queue cos-map qid cos0 [cos...

  • Page 485

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 477 48-13 queue bandwidth this command is used to specify or modify the bandwidth allocated for a cos. To remove the bandwidth allocated for a cos, use the no form of this command. Queue queue-id bandwidth min max no queue queue-id bandwidth...

  • Page 488

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 480 48-17 show class-map this command is used to display the quality of service (qos) class maps, which define the match criteria to classify traffic. Show class-map [class-map-name] parameters 48-18 show mls qos interface this command is us...

  • Page 492

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 484 48-23 show policy-map this command is used to display quality of service (qos) policy maps, which defines the classification criteria for incoming or outgoing traffic. Show policy-map [policy-map-name [class class-map-name]] parameters u...

  • Page 493

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 485 48-24 wdrr-queue bandwidth this command is used to set the queue weight in the wdrr scheduling mode. To restore to the default setting, use the no form of this command. Wdrr-queue bandwidth weight1...Weight8 no wdrr-queue bandwidth param...

  • Page 494

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 486.

  • Page 496

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 488 49-3 qcn cnm-transmit-priority this command is used to configure the ieee 802.1p priority for transmitting congestion notification messages (cnms). Use the no form of this command to reset to the default setting. Qcn cnm-transmit-priorit...

  • Page 500

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 492 49-7 show qcn cnpv this command is used to display the qcn cnpv settings and status. Show qcn cnpv [status] parameters usage guideline the command is available for physical port configuration. The congestion point (cp) index is decided b...

  • Page 503

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 495 49-10 show qcn cpid this command is used to display the relationship between the cp identifier, interface, and cp index. Show qcn cpid cp-identifier parameters all specifies to display cp information for all interfaces. Interface interfa...

  • Page 504

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 496 command mode exec mode. Command default level level: 3. Usage guideline use this command to display the corresponding interface id and cp index for the specified cp identifier. Example this example shows how to display the interface id a...

  • Page 505: Radius Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 497 radius commands 50-1 radius-server host this command is used to specify a radius security server host. The no form of this command without parameter is used to delete the radius server host. The no form of this command with the parameter...

  • Page 506

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 498 parameters 50-3 radius-server retransmit this command is used to configure the number of packet retransmissions before the device considers that the radius security server does not respond. The no form of this command is used to restore ...

  • Page 507

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 499 parameters 50-5 show radius statistics this command is used to display the radius statistics for accounting and authentication packets. Show radius statistics seconds specifies the timeout value in the range of 1 to 1000 seconds. Default...

  • Page 508

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 500 50-6 show radius-server configuration this command is used to display the radius authentication & accounting server configuration. Show radius-server configuration access accepts the number of radius access-accept packets (valid or inval...

  • Page 509

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 501 example this example shows the output for the show radius authentication & accounting server hosts command. Dxs-3600-32s#show radius-server configuration ip-address auth-port acct-port key retransmit timeout -----------------------------...

  • Page 510

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 502 remote network monitoring (rmon) commands 51-1 rmon collection stats this command is used to add a statistic entry. Use the no form of this command to remove a statistic entry. Rmon collection stats index [owner ownername] no rmon collec...

  • Page 512

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 504 51-4 rmon event this command is used to add an event entry. Use the no form of this command to remove an event entry. Rmon event number [log] [trap community] [description description-string] no rmon event number parameters 51-5 show rmo...

  • Page 513

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 505 51-6 show rmon history this command is used to display history control and history data information. Show rmon history usage guideline statistics is the first group in rmon. It measures the basic statistics information of each monitored ...

  • Page 514

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 506 51-7 show rmon alarm this command is used to display alarm information. Show rmon alarm example this example shows how to display the rmon history entry. Dxs-3600-32s#show rmon history entry : 1 data source : 1.3.6.1.2.1.2.2.1.1.1 bucket...

  • Page 515

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 507 51-8 show rmon event this command is used to display event information. Show rmon event parameters none. Default none. Command mode privileged exec mode. Command default level level: 3 usage guideline event is the ninth group in rmon. It...

  • Page 516

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 508 routing information protocol (rip) commands 52-1 route-preference this command is used to configure the route preference for the routing information protocol (rip) routes. Use the no form of this command to restore to the default value. ...

  • Page 517

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 509 52-3 ip rip authentication mode this command is used to configure the simple password authentication type used by rip interface. Use the no form of this command to restore to the default value. Ip rip authentication mode text no ip rip a...

  • Page 518

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 510 52-4 ip rip authentication text-password this command is used to configure the plaintext password for rip simple password authentication. Use the no form of this command to remove the plaintext password. Ip rip authentication text-passwo...

  • Page 520

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 512 52-7 ip rip send enable this command is used to send rip packets on a rip interface. Use the no form of this command to prohibit sending rip packets on the interface. Ip rip send enable no ip rip send enable 52-8 ip rip send version this...

  • Page 521

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 513 52-9 ip rip v2-broadcast this command is used to send rip version 2 update packets as a broadcast instead of multicast. Use the no form of this command to restore to the default value. Ip rip v2-broadcast no ip rip v2-broadcast command m...

  • Page 522

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 514 52-10 network this command is used to enable rip on one interface. Use the no form of this command to restore to the default setting. Network network-number no network parameters 52-11 redistribute (rip) this command is used to redistrib...

  • Page 523

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 515 52-12 router rip this command is used to enable rip and enter the rip router configuration mode. Use the no form of this command to disable rip. Router rip default by default, no route redistribution to rip is configured. The default val...

  • Page 524

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 516 no router rip 52-13 show ip rip this command is used to show the rip information. Show ip rip [vrf vrf-name] parameters parameters none. Default by default, rip is disabled. Command mode global configuration mode. Command default level l...

  • Page 525

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 517 example this example shows how to display rip information. Dxs-3600-32s#show ip rip rip global state : enabled update time : 30 seconds timeout time : 180 seconds garbage collection time : 120 seconds rip interface settings interface ip ...

  • Page 526

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 518 52-14 show ip rip interface this command is used to show information of all rip interfaces. Show ip rip interface [vrf vrf-name] parameters timeout time interval of time (in seconds) after which a route is declared invalid. It is specifi...

  • Page 527

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 519 52-15 timers basic this command is used to configure rip timers. Use the no form of this command to restore to the default value. Example this example shows how to check the settings of all rip interfaces. Dxs-3600-32s#show ip rip interf...

  • Page 528

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 520 timer basic update timeout garbage_collection no timer basic parameters 52-16 version this command is used to configure the default version for all rip interfaces to send or receive rip packets. Use the no form of this command to restore...

  • Page 529

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 521 parameters 52-17 address-family ipv4 vrf (rip) this command is used to create an rip vrf instance and enter the rip vrf address family configuration mode. Use the no form of this command to remove the rip vrf instance. Address-family ipv...

  • Page 530

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 522 52-18 exit address-family this command is used to exit the address family configuration mode. Exit address-family example this example shows how to create a new rip instance in vrf vpn-a. Dxs-3600-32s#configure terminal dxs-3600-32s(conf...

  • Page 531: Route Map Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 523 route map commands 53-1 route-map this command is used to create or configure a route map or enter route map configuration mode. Use the no form of this command to delete a route map or remove a clause of route map. Route-map map-name [p...

  • Page 532

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 524 53-2 match as-path this command is used to add a match command to match a bgp autonomous system (as) path access list. Use the no form of this command to delete the match command with bgp autonomous system path access list. Match as-path...

  • Page 533

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 525 53-4 match extcommunity this command is used to add a match command to match a border gateway protocol (bgp) extended community (extcommunity) list. Use the no form of this command to delete the match command with bgp extended community ...

  • Page 534

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 526 53-6 match ip address this command is used to add a match command to match the destination network address of routes. Use the no form of this command to delete the match command with destination network address of routes. Match ip addres...

  • Page 536

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 528 53-9 match metric this command is used to add a match command to match the metric of routes. Use the no form of this command to delete the match command with metric of routes. Match metric number no match metric parameters 53-10 match ro...

  • Page 537

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 529 53-11 set as-path prepend this command is used to add a set command to modify an autonomous system path of bgp routes. Use the no form of this command to delete this set command. Set as-path prepend aspath-list no set as-path prepend par...

  • Page 538

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 530 53-13 set dampening this command is used to add a set command specify the dampening parameters of routes. Use the no form of this command to delete this set command. Set dampening half-life reuse suppress max-suppress-time un-reachabilit...

  • Page 540

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 532 parameters 53-16 set metric this command is used to add a set command to modify the metric of routes. Use the no form of this command to delete this command. Set metric number no set metric parameters number specifies the value of local ...

  • Page 542

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 534 53-19 set weight this command is used to add a set command to specify the weight of bgp routes. Use the no form of this command to delete this set command. Set weight number no set weight parameters 53-20 show route-map this command is u...

  • Page 543

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 535 parameters map-name (optional) specifies to display information about specified route map. The maximum length is 16 characters. Default none. Command mode privileged mode. Command default level level: 3 usage guideline use this command t...

  • Page 544: Secure Shell (Ssh) Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 536 secure shell (ssh) commands 54-1 ip ssh time-out this command is used to specify the time interval that the switch waits for the ssh client to respond. Use the no form of this command to reset the time interval that the switch waits for ...

  • Page 545

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 537 54-3 ip ssh port this command is used to specify the tcp port number on which ssh server listens. Use the no form of this command to reset the tcp port number to the default value 22. Ip ssh port int 1-65535> no ip ssh port parameters 54...

  • Page 546

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 538 54-5 show ip ssh server this command is used to show the version and configuration information of the ssh server. Show ip ssh server 54-6 show ip ssh sessions this command is used to show the status of ssh server connections on the switc...

  • Page 547: Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 539 simple network management protocol (snmp) commands 55-1 snmp-server this command is used to enable the simple network management protocol (snmp) agent. To stop and shield the snmp agent, use the no form of this command. Snmp-server no sn...

  • Page 548

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 540 55-3 snmp-server name this command is used to configure the system name information in global configuration mode. Use the no form of this command to remove the configuration of system name information. Snmp-server name text no snmp-serve...

  • Page 549

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 541 55-5 snmp-server location this command is used to configure the system location information in global configuration mode. Use the no form of this command to remove the configuration of system location information. Snmp-server location te...

  • Page 551

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 543 v3 specifies that snmpv3 should be used for the group. Smnpv3 is the most secure of the supported security models, as it allows you to explicitly configure the authentication characteristics. Auth specifies authentication of a packet wit...

  • Page 555

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 547 55-12 show snmp community this command is used to display information about the configured characteristics of snmp community. Show snmp community default no host entry exists. Command mode global configuration mode. Command default level...

  • Page 556

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 548 55-13 show snmp user this command is used to display information about the configured characteristics of snmp user. Show snmp user 55-14 show snmp group this command is used to display information about the configured characteristics of ...

  • Page 557

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 549 55-15 show snmp view this command is used to display information about the configured characteristics of snmp view. Show snmp view usage guideline used this command can view the snmp groups configured on the current snmp agent. Example t...

  • Page 558

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 550 55-16 show snmp host this command is used to display information about the configured characteristics of snmp host. Show snmp host example this example shows how to display the snmp view information. Dxs-3600-32s#show snmp view restricte...

  • Page 559: Mands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 551 simple network time protocol (sntp) and clock com- mands 56-1 sntp enable this command is used to enable the sntp function. Use the no form of this command to restore the default value. Sntp enable no sntp enable 56-2 sntp server this co...

  • Page 560

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 552 56-3 sntp interval this command is used to set the interval for the sntp client to synchronize its clock with the ntp server. Sntp interval seconds no sntp interval parameters 56-4 show sntp this command is used to to show the sntp infor...

  • Page 561

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 553 56-5 clock set this command is used to manually set the system clock. Clock set hh:mm:ss ddmmmyyyy parameters example this example shows how to check the sntp information. Dxs-3600-32s#show sntp sntp status : enabled sntp poll interval :...

  • Page 562

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 554 56-6 clock timezone this command is used to set the time zone for display purposes. To set the time to coordinated universal time (utc), use the no form of this command. Clock timezone hours-offset [minutes-offset] no clock timezone para...

  • Page 563

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 555 56-8 show clock this command is used to display the time and date from the system clock. Show clock [detail] parameters command default level level: 8 usage guideline in both the date and repeating forms of the command, the first part of...

  • Page 564

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 556.

  • Page 565

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 557 spanning tree protocol (stp) commands 57-1 spanning-tree (global configuration) this command is used to enable the stp mode. Use no form to disable stp. Spanning-tree no spanning-tree 57-2 spanning-tree reset this command is used to rest...

  • Page 566

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 558 parameters 57-4 spanning-tree tx-hold-count this command is used to limit the maximum bpdu transmission rate for every port. Use the no form of this command to return the setting to default setting. Spanning-tree transmit-hold-count tx-h...

  • Page 567

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 559 57-5 spanning-tree max-hops this command is used to configure the mstp related max-hops timers. Use the no form of this command to return the setting to default setting. Spanning-tree max-hops max-count no spanning-tree max-hops paramete...

  • Page 568

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 560 57-7 spanning-tree mst configure this command is used to enter the mst configuration mode in the global configuration mode and configure the mstp region. Use the no form of the command to restore all parameters (name, revision, vlan map)...

  • Page 570

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 562 57-10 revision_level this command is used to set the revision number for the mst configuration. To return to the default settings, use the no form of this command. Revision_level revision no revision_level parameters usage guideline two ...

  • Page 571

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 563 57-11 spanning-tree mst this command is used to set the path cost and port-priority parameters for any mst instance (including the cist with instance id 0). To return to the default settings, use the no form of this command. Spanning-tre...

  • Page 572

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 564 57-13 clear spanning-tree detected-protocols this command is used to restart the protocol migration. Clear spanning-tree detected-protocols [interface interface-id] parameters 57-14 spanning-tree (interface configuration) this command is...

  • Page 573

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 565 spanning-tree no spanning-tree 57-15 spanning-tree hello-time this command is used to configure the mstp port hello time. Use the no form of this command to return the setting to default setting. Spanning-tree hello-time seconds no spann...

  • Page 574

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 566 no spanning-tree externalcost parameters 57-17 spanning-tree portfast this command is used to enable fast forwarding mode where the interface is immediately put into the forwarding state upon linkup without waiting for the timer to expir...

  • Page 575

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 567 57-18 spanning-tree autoedge this command is used to enable auto-edge on the interface. Use the disabled option of this command to disable auto- edge on the interface. Spanning-tree autoedge [disabled] parameters 57-19 spanning-tree guar...

  • Page 578

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 570 example this example shows how to display the global configuration of stp summary. Dxs-3600-32s#show spanning-tree summary stpversion : rstp stpstatus : disabled bridgemaxage : 21 bridgehellotime : 1 bridgeforwarddelay : 16 maxhops : 19 ...

  • Page 581

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 573 example this example shows mstp instance information. Dxs-3600-32s#show spanning-tree mst instance 0 ###### mst 0 vlans mapped : 1-4094 bridgeaddr : 0001.0203.0400 priority : 32768 timesincetopologychange : 0d:0h:0m:0s topologychanges : ...

  • Page 585

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 577 example this example shows the storm control information for all interfaces. Dxs-3600-32s#show storm-control function version : 1.01 storm control statistic interval: 5(seconds) interface type lower upper action status --------- --------...

  • Page 586: Switch Management Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 578 switch management commands 59-1 login (console) this command is used to login to the device. Login 59-2 logout this command is used to logout of the device. Logout parameters none. Default none. Command mode exec mode. Command default le...

  • Page 589

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 581 parameters 59-8 disable this command is used to leave a privilege level. Disable [privilege-level] parameters 59-9 enable password this command is used to create a privilege level password. Enable password [level privilege-level] {passwo...

  • Page 590

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 582 59-10 service password-encryption this command is used to encrypt the password used. The no form of this command restores to the default value. Service password-encryption no service password-encryption 59-11 show privilege this command ...

  • Page 591

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 583 59-12 privilege this command is used to change the command string execution rights to a specific level. The no form of this command restores the command string, on this mode execution, to it’s default rights. Privilege mode {level privil...

  • Page 592: Syslog Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 584 syslog commands 60-1 logging on this command is used to turn on logging of system messages. Use no form of this command to turn off the logging. Logging on no logging on 60-2 logging server this command is used to send system log message...

  • Page 593

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 585 60-3 logging console this command is used to set the severity of logs that are allowed to be displayed on the console. The no format of the command disable show log on console. Logging console level no logging console parameters 60-4 log...

  • Page 595

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 587 60-7 logging count this command is used to enable the log statistics function. The no format of the command deletes the log statistics and disables the statistics function. Logging count no logging count default local7. Command mode glob...

  • Page 596

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 588 60-8 clear logging this command is used to clear the logs from the buffer. Clear logging 60-9 show logging this command is used to display the logs in the buffer. Show logging command default level level: 15 usage guideline this command ...

  • Page 597

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 589 60-10 show logging count this command is used to show the log statistics. Show logging count 60-11 logging buffered this command is used to set the memory buffer parameters for logs. The no form of the command disables recording logs in ...

  • Page 598

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 590 60-12 save log this command is used to save the log. Save log usage guideline the memory buffer for the log is used in a recycled manner. That is, when it is full, the oldest information will be overwritten. The content of the logging bu...

  • Page 599: Tacacs+ Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 591 tacacs+ commands 61-1 tacacs-server host this command is used to configure the ip address of tacacs+ server host. The no form of this command without parameters is used to delete the tacacs+ server host. The no form of this command with ...

  • Page 600

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 592 61-3 tacacs-server timeout this command is used to configure the global timeout time waiting for the server when communicatin with tacacs+ server. Tacacs-server timeout seconds no tacacs-server timeout parameters 61-4 show tacacs statist...

  • Page 601

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 593 61-5 show tacacs-server configuration this command is used to display the tacacs+ server configuration. Show tacacs-server configuration example this example shows how to display all the server groups configured for tacacs+. Dxs-3600-32s...

  • Page 602

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 594 default timeout the global timeout time waiting for the server when communicating with tacacs+ server. Display parameters description.

  • Page 603: Telnet Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 595 telnet commands 62-1 ip telnet server enable this command is used to enable the telnet server on the switch. Use the no form of this command to disable the telnet server on the switch. Ip telnet server enable no ip telnet server enable 6...

  • Page 604

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 596 default none. Command mode privileged mode. Command default level level: 8 usage guideline this command is used to display the telnet server information. Example this example shows how to display the telnet server information. Dxs-3600-3...

  • Page 605: Time Range Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 597 time range commands 63-1 time-range this command is used to enter the time range configuration mode in the global configuration mode. To delete a time range, use the no to form of this command. Time-range range_name 32> no time-range ran...

  • Page 606

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 598 63-3 show time-range this command is used to display all existing time ranges. Show time-range example this example shows how to configure a new time range called time1. Dxs-3600-32s#configure terminal dxs-3600-32s(config)#time-range tim...

  • Page 607

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 599 traffic segmentation commands 64-1 switchport protected unidirectional this command is used to enable the interface isolated to a specified interface list for unidirectional protected. Use the no form of the command to disable the interf...

  • Page 608

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 600 example this example shows how to display the switch port’s protected unidirectional information for interface 1. Dxs-3600-32s#show switchport protected interface tengigabitethernet 1/0/1 function version: 1.01 interface unidirectional p...

  • Page 609

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 601 upgrade and maintenance commands 65-1 copy this command is used to upgrade and maintain the switch by use of the tftp protocol for uploads and downloads. Copy flash: filename tftp://location/filename copy tftp://location/filename flash: ...

  • Page 610

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 602 65-3 show bootup this command is used to display the boot up file information. Show bootup default none. Command mode global configuration mode. Command default level level: 15 usage guideline by default, the switch attempts to automatic...

  • Page 612

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 604 66-2 name this command is used to specify the name of a vlan. Use the no name command to reset the vlan name to the default vlan name. Name vlan-name no name parameters 66-3 switchport mode this command is used to specify the vlan mode f...

  • Page 613

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 605 66-4 switchport access vlan this command is used to specify the access vlan for the interface. Use no switchport access vlan interface command to reset to default setting. Switchport access vlan vlan-id no switchport access vlan paramete...

  • Page 614

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 606 66-5 switchport trunk allowed vlan this command is used to configure the vlans that will be allowed to receive and send traffic on the specified interface in a tagged format. Use the no switchport trunk allowed vlan command to reset the ...

  • Page 615

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 607 66-6 switchport hybrid allowed vlan this command is used to specify if the port will be a tagged or untagged member of the specified vlan for a hybrid port. Use the no switchport hybrid allowed vlan command to reset the membership. Switc...

  • Page 617

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 609 66-9 ingress-checking this command is used to enable the ingress checking of the received frames on a port. Use the no ingress-checking interface command to disable the ingress checking function. Ingress-checking no ingress-checking 66-1...

  • Page 618

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 610 66-11 subnet-base (vlan) this command is used to specify subnet-based vlan id assignment entry for un-tagged incoming packets. Use the no subnet-base command to remove a subnet-based vlan id assignment entry. Subnet-base {network-prefix ...

  • Page 620

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 612 example this example displays all the current vlan entries. Dxs-3600-32s#show vlan vlan 1 name : default tagged member ports : 1/0/1 untagged member ports : 1/0/2-1/0/24 vlan 100 name : vlan0100 tagged member ports : 1/0/1 untagged membe...

  • Page 622

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 614 66-14 protocol-vlan profile (interface) this command is used to bind the protocol vlan classification rule to a port. The no protocol-vlan profile command is used to remove the binding of a protocol vlan classification from the port. Pro...

  • Page 623

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 615 66-15 show protocol-vlan this command is used to display the configuration settings of a protocol vlan. The show protocol-vlan profile command displays the protocol vlan list and its protocols. The show protocol-vlan interface command di...

  • Page 624

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 616 virtual private lan service (vpls) commands 67-1 vpls this command is used to create a vpls and enter the vpls configuration mode. Use the no vpls command to delete a vpls. Vpls vpls-name no vpls vpls-name parameters 67-2 vpls-id this co...

  • Page 627

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 619 67-6 peer backup this command is used to create a backup peer for pw redundancy of h-vpls. Peer backup ip-address [vc-id] parameters example this example shows how to delete a peer from a vpls with the ip address if 2.2.2.2 and vc id of ...

  • Page 628

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 620 67-7 xconnect vpls this command is used to create a local ac in a vpls. Use the no xconnect vpls command to delete a local ac in a vpls. Xconnect vpls vpls-name no xconnect vpls vpls-name parameters example this example shows how to crea...

  • Page 629

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 621 67-8 show vpls this command is used to display vpls information. Show vpls [vpls-name] [detail] parameters example this example shows how to delete a local ac, which is an ethernet-based ac and the ethernet port is 1/0/1, from a vpls nam...

  • Page 630

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 622 example this example shows how to display vpls information for a vpls. Dxs-3600-32s#show vpls vpls100 vpls name vpls id peers/acs oper status -------------------------------- ---------- --------- ----------- vpls100 100 3/1 up total entr...

  • Page 632

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 624 example this example shows how to display all vpls mac address information. Dxs-3600-32s#show mac-address-table vpls vpls name mac address peer (vc id/ip) or ac -------------------------------- ----------------- -------------------------...

  • Page 634

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 626 67-11 show mpls l2transport vc this command is used to display vc information for vpws and vpls. Show mpls l2transport vc [vc-id] [detail] parameters interface interface-id (optional) specifies the ethernet interface of a local ac. Vlan ...

  • Page 635

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 627 example this example shows how to display all vc information, including vpws and vpls. Dxs-3600-32s#show mpls l2transport vc vc id peer local ac type oper status ---------- -------------- -------------------- ------ ----------- 1 150.1.1...

  • Page 637

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 629 pe2: 68-2 show mpls l2transport vc this command is used to display the vpws vc information. Show mpls l2transport vc [vc-id] [detail] parameters dxs-3600-32s(config)#interface vlan 20 dxs-3600-32s(config-if)#mpls ip dxs-3600-32s(config-i...

  • Page 638

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 630 68-3 xconnect backup this command is used to enable the pw redundancy of the vpws service on an interface. Use the no xconnect backup command to cancel the pw redundancy of the vpws service. Xconnect backup vc-id ip-address no xconnect b...

  • Page 639

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 631 parameters vc-id specifies the pw service instance id. It is used to uniquely identify the vpws and it must be unique at both pes. The range is 1-4294967295. Ip-address specifies the peer lsr id that is used to identify the other end’s p...

  • Page 640: Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 632 virtual router redundancy protocol (vrrp) commands 69-1 vrrp authentication this command is used to enable vrrp authentication and set the password on an interface. Use the no form of this command to remove the authentication. Vrrp authe...

  • Page 641

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 633 69-3 vrrp ip this command is used to create a vrrp router. Use the no form of this command to remove a vrrp router. Vrrp vrid ip ip-address no vrrp vrid parameters 69-4 vrrp preempt this command is used to allow a router to take over the...

  • Page 642

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 634 vrrp vrid preempt no vrrp vrid preempt parameters 69-5 vrrp priority this command is used to set the priority of a virtual router. Use the no form of this command to restore to the default priority, vrrp vrid priority priority no vrrp vr...

  • Page 643

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 635 69-6 vrrp timers advertise this command is used to configure the interval between successive vrrp advertisements by the master router. Use the no form of this command to restore to the default value. Vrrp vrid timers advertise interval n...

  • Page 644

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 636 69-7 show vrrp this command is used to display the vrrp status. Show vrrp [interface ipif_name [group vrid]] [brief] parameters example this example shows how to configure the router to send advertisements for vrrp 7 every 10 seconds on ...

  • Page 645

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 637 example this example shows brief information about the group 1 on interface ‘vlan1’. Dxs-3600-32s#show vrrp interface vlan1 group 1 brief interface grp pri own pre state master addr group addr vlan1 1 255 y y master 10.1.1.1 10.1.1.1 dxs...

  • Page 646

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 638 69-8 debug vrrp this command is used to turn on the vrrp debug function. Use the no form of the command to turn off the vrrp debug function. Debug vrrp no debug vrrp 69-9 debug vrrp errors this command is used to turn on the vrrp error p...

  • Page 647

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 639 69-10 debug vrrp events this command is used to turn on the vrrp event debug switch. Use the no form of the command to turn off the vrrp event debug switch. Debug vrrp events no debug vrrp events 69-11 debug vrrp packets this command is ...

  • Page 648

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 640 69-12 debug vrrp state this command is used to turn on the vrrp state debug switch. Use the no form of the command to turn off the vrrp state debug switch. Debug vrrp state no debug vrrp state 69-13 debug vrrp log this command is used to...

  • Page 649

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 641.

  • Page 650: Vlan Mapping Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 642 vlan mapping commands 70-1 vlan mapping profile this command is used to enter the vlan mapping profile configuration mode. If the vlan mapping profile doesn’t exist, it will be created. Use no command to remove the vlan mapping profile. ...

  • Page 651

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 643 ether-type value specifies the ethernet type. Src-ip network-prefix specifies the source ipv4 address. Dst-ip network-prefix specifies the destination ipv4 address. Src-ipv6 ipv6-network- prefix / prefix- length specifies the source ipv6...

  • Page 652

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 644 70-3 show vlan mapping profile this command is used to display previously configured vlan mapping profile information. Show vlan mapping profile [id] parameters 70-4 switchport vlan mapping profile this command is used to apply the vlan ...

  • Page 653

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 645 usage guideline use this command to apply the vlan mapping profile to specified interface. The interface can be a physical port or a link aggregation group which is set to dot1q tunnel mode. If a profile is applied on an interface, the s...

  • Page 654: Vlan Tunnel Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 646 vlan tunnel commands 71-1 switchport mode dot1q-tunnel this command is used to specify the port as a dot1q-tunnel port. Use the no command to reset the vlan mode to default setting. Switchport mode dot1q-tunnel no switchport mode paramet...

  • Page 655

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 647 71-2 frame-tag tpid this command is used to specify the outer tpid associated with a nni port. Frame-tag tpid tpid no frame-tag tpid parameters 71-3 switchport vlan mapping this command is used to specify the vlan translation or selectiv...

  • Page 656

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 648 command mode interface configuration mode. Command default level level: 12 usage guideline this command can be configured on physical ports or link aggregation groups. This command specifies the vlan translation or selective qinq rule on...

  • Page 657

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 649 71-4 inner-priority-trust this command is used to set the trusting dot1q priority. Use no command to remove the setting. Inner-priority-trust 71-5 insert-dot1q-tag this command is used to specify the dot1q vlan tag inserting. Use the no ...

  • Page 658

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 650 71-6 vlan mapping miss drop this command is used to enable the dropping of vlan mapping unmatched packets. Use the no command to disable the vlan mapping miss dropping action. Vlan mapping miss drop no vlan mapping miss drop 71-7 show do...

  • Page 660

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 652 parameters interface interface-id (optional) specifies the interfaces that will be displayed. If not specified, display the all vlan mapping. Default none. Command mode exec mode. Command default level level: 3 usage guideline use this c...

  • Page 661: Vrf-Lite Commands

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 653 vrf-lite commands 72-1 address-family ipv4 vrf this command is used to enter the vrf address family configuration mode. Use the no form of this command to disable vrf address family configuration mode. Address-family ipv4 vrf vrf-name no...

  • Page 662

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 654 72-3 import map this command is used to configure the import route map of one vrf. Use the no form of this command to delete the import route map. Import map route-map no import map parameters 72-4 ip vrf this command is used to create a...

  • Page 663

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 655 72-5 ip vrf forwarding this command is used to associate one interface to a vrf instance. Use the no form of this command to restore one interface to global routing instance. Ip vrf forwarding vrf-name no ip vrf forwarding vrf-name param...

  • Page 664

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 656 no maximum routes parameters 72-7 rd this command is used to set the route distinguisher of one vrf. Rd route-distinguisher parameters limit specifies the maximum number of routes within the vrf. Its ranges from 1 to 16384. Warn-threshol...

  • Page 666

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 658 example this example shows how to check the current vrf settings. Dxs-3600-32s#show ip vrf vrf name rd interfaces ---------------------- --------------------- ---------------------- vpn-a 100:1 ip100 vpn-b not set dxs-3600-32s# example t...

  • Page 667

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 659 weighted random early detection (wred) commands 73-1 clear random-detect drop-counter this command is used to clear wred drop counters. Clear random-detect drop-counter 73-2 random-detect this command is used to enable the wred function....

  • Page 668

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 660 73-3 random-detect exponential-weight this command is used to configure the wred exponential weight factor for the average queue size calculation for the queue. The no form is used to configure it to the default setting. Random-detect ex...

  • Page 671

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 663 parameters profile id specifies the wred profile id for which the wred profile configuration will be displayed. If not specified, the configuration for all wred profiles will be displayed. Default none. Command mode exec mode. Command de...

  • Page 672

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 664 appendix a - password recovery procedure this section describes the procedure for resetting passwords on the d-link dxs-3600-32s switch. Authenticating any user who tries to access networks is necessary and important. The basic authentic...

  • Page 673

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 665 appendix b - system log entries the following table lists all possible entries and their corresponding meanings that will appear in the system log of this switch. Category log description severity note ip directed- broadcast event descri...

  • Page 674

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 666 event description: configuration successfully downloaded. Log message: [tftp(5):]configuration successfully downloaded by (username: , ip: , mac: ) parameters description: session: the user’s session. Username: represent current login us...

  • Page 675

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 667 dns resolver event description: duplicate domain name cache added. This will lead to the dynamic domain name cache being deleted log message: [dns_resolver(1):]duplicate domain name case name: , static ip: , dynamic ip: parameters descri...

  • Page 676

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 668 802.1x event description: 802.1x authentication failure. Log message: 802.1x authentication failure [for ] from (username: , , mac: ) parameters description: reason: the reason for the failed authentication. Username: the user that is be...

  • Page 677

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 669 event description: the 802.1p default priority assigned from the radius server after the radius client was successfully authenticated by the radius server. This 802.1p default priority will be assigned to the port. Log message: radius se...

  • Page 678

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 670 event description: conflict lldp-med device type detected. Log message: conflict lldp-med device type detected (on port >, chassis id: , , port id: , , device class: ) parameters description: portnum: the port number. Chassistype: the ch...

  • Page 679

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 671 bgp event description: the bgp fsm with peer has gone to the successfully established state. Log message: [bgp(1):] bgp connection was successfully established (peer:). Parameters description: ipaddr: the ip address of the bgp peer. Info...

  • Page 680

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 672 event description: the number of bgp prefixes received from the neighbor reached the threshold. Log message: [bgp(8):] the number of prefixes received reached , max (peer ). Parameters description: num: the number of prefix received. Lim...

  • Page 682

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 674 event description: one ospf neighbor state changed from loading to full. Log message: ospf nbr on interface changed state from loading to full. Parameters description: intf-name: the name of the ospf interface. Nbr-id: the neighbor's rou...

  • Page 683

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 675 event description: one virtual router’s state becomes initiate. Log message: vr at interface switched to init parameters description: vr-id: the vrrp virtual router id. Intf-name: the virtual router’s interface name. Informational event ...

  • Page 684

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 676 event description: a virtual mac address was added into the switch’s l3 table. Log message: added a virtual ip mac into the switch’s l3 table. Parameters description: vrrp-ip-addr: the vrrp virtual ip address. Vrrp-mac-addr: the vrrp vir...

  • Page 685

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 677 event description: failed when adding a virtual mac into the switch’s l3 table. The box where the mac was learned from is invalid. Log message: failed to add virtual ip mac into the switch’s l3 table. Box id is invalid. Parameters descri...

  • Page 686

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 678 port security event description: port security violation. Log message: port security violation. (mac address: on ) parameters description: macaddr: the violation mac address. Interface-id: the interface name. Warning ssh event descriptio...

  • Page 688

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 680 event description: broadcast storm cleared. Log message: broadcast storm has cleared. Parameters description: interface-id: the interface name. Informational event description: multicast storm occurrence. Log message: multicast storm is ...

  • Page 689

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 681 event description: spanning tree port status changed. Log message: spanning tree port status changed [( [instance: ], port:)] -> parameters description: instanceid: the instance id. Portnum: the port id. Old_status: the old status. New_s...

  • Page 690

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 682 module event description: module inserted and working. Log message: module is inserted. Parameters description: module-type: the expansion module name. Informational event description: module inserted and not working. Log message: module...

  • Page 691

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 683 event description: temperature sensor enters alarm state. Log message: temperature sensor enters alarm state (current temperature: ) parameters description: sensorid: the sensor id. Temperature: the temperature. Warning event description...

  • Page 692

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 684 vpls event description: vpls link up. Log message: vpls link up. Parameters description: vpls_name: the name of the link up vpls. Informational event description: vpls link down. Log message: vpls link down. Parameters description: vpls_...

  • Page 693: Appendix C - Trap Entries

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 685 appendix c - trap entries this table lists the trap logs found on the switch. Category trap name description oid vrrp vrrptrapnewmaster the newmaster trap indicates that the sending agent has transitioned to 'master' state. Binding objec...

  • Page 694

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 686 authentication authenticationfailure an authenticationfailure trap signifies that the snmpv2 entity, acting in an agent role, has received a protocol message that is not properly authenticated. While all implementations of the snmpv2 mus...

  • Page 695

    Dxs-3600 series 10gbe layer 2/3 switch cli reference guide 687 lacp linkup a linkup trap signifies that the snmp entity, acting in an agent role, has detected that the ifoperstatus object for one of its communication links left the down state and transitioned into some other state (but not into the ...