1. DL manuals
  2. D-Link
  3. Switch
  4. DXS-3600 Series
  5. Cli Reference Manual

D-Link DXS-3600 Series Cli Reference Manual - Interface Notation

Other manuals for DXS-3600 Series: Reference Manual, Reference Manual, Reference Manual
Manual is about: Layer 2/3 Managed 10Gigabit

Summary of DXS-3600 Series

  • Page 2: Table Of Contents

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide i table of contents 1. Introduction ...................................................................................................................................................................... 1 2. Basic cli comm...

  • Page 3

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide ii 39. Ethernet ring protection switching (erps) commands ......................................................................................... 490 40. Expansion module commands ...........................................

  • Page 4

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide iii 79. Power saving commands ........................................................................................................................................ 991 80. Priority-based flow control (pfc) commands .......

  • Page 5

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide iv 119. Virtual router redundancy protocol (vrrp) commands ................................................................................ 1375 120. Virtual routing and forwarding lite (vrf-lite) commands ...................

  • Page 6: 1.  Introduction

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1 1. Introduction this manual’s command descriptions are based on the software release 2.40, running in the enhanced license (ei) mode. The commands listed here are the subset of commands that are supported by the dxs-3600...

  • Page 7: Notes, Notices, and Cautions

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 2 notes, notices, and cautions below are examples of the three types of indicators used in this manual. When administering your switch using the information in this document, you should pay special attention to these indic...

  • Page 8

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 3 • power user - privilege 8. This user account level can execute fewer commands than operator, including configuration commands other than the operator level and administrator level commands. • operator - privilege level ...

  • Page 9

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 4 privileged exec mode / operator level for changing both local and global terminal settings, monitoring, and performing certain system administration tasks. The system administration tasks that can be performed at this le...

  • Page 10: Creating A User Account

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 5 access other sub-configuration modes. In order to access the global configuration mode, the user must be logged in with the corresponding account level and use the configure terminal command in the privileged exec mode. ...

  • Page 11: Interface Notation

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 6 • after accessing the privileged exec mode, we entered the command configure terminal to access the global configuration mode. The username command can be used in the global configuration mode. • the command username adm...

  • Page 12: Error Messages

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 7 in the above example the notation 1/0/1 was used. The terminology for each parameter is as follows: • interface unit’s id / open slot’s id / port’s id the interface unit’s id is the id of the stacking unit without the ph...

  • Page 13

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 8 keystroke description delete deletes the character under the cursor and shifts the remainder of the line to the left. Backspace deletes the character to the left of the cursor and shifts the remainder of the line to the ...

  • Page 15: 2.  Basic Cli Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 10 2. Basic cli commands 2-1 help this command is used to display a brief description of the help system. Use the help command in any command mode. Help parameters none. Default none. Command mode user exec or any configur...

  • Page 16

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 11 switch# the following example shows how to use the word help to display all the privileged exec mode commands that begin with the letters “re”. The letters entered before the question mark (?) are reprinted on the next ...

  • Page 17

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 12 switch# enable 15 password:*** switch# 2-3 disable this command is used to downgrade to a level lower user level than the privileged level. Disable [privilege-level] parameters privilege level specifies the privilege le...

  • Page 18

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 13 command default level level: 12. Usage guideline this command is used to enter the global configuration mode. Example this example shows how to enter into global configuration mode. Switch# configure terminal switch(con...

  • Page 19

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 14 login [local] no login parameters login specifies that the line login method will be login. Local specifies that the line login method will be local. Default by default, there is no login details configured for the cons...

  • Page 20

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 15 this example shows how to configure the line console login method as “login”. Switch# configure terminal switch(config)# line console switch(config-line)# login switch(config-line)# this example shows how to enter the l...

  • Page 21

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 16 example this example shows how to logout switch# disable switch# logout 2-8 end this command is used to end the current configuration mode and return to the highest mode in the cli mode hierarchy which is either the use...

  • Page 22

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 17 none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to exit the current configuration mode and go back to the last mode. When the user is in the user ...

  • Page 23

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 18 switch# show history help history switch# 2-11 password-recovery this command is used to recover the password related settings. Use the password recovery command in the reset configuration mode. Password-recovery parame...

  • Page 24

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 19 do you want to update the enable password for privilege level 15? (y/n) [n]y please input privilege level 15 enable password: do you want to disable aaa function to let the system do the local authentication? (y/n) [n] ...

  • Page 25

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 20 switch# display parameters power status in-operation: the power rectifier is in normal operation. Failed: the power rectifier not working normally. Empty: the power rectifier is not installed. 2-13 show unit this comman...

  • Page 26

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 21 2-14 show cpu utilization this command is used to display the cpu utilization information. Show cpu utilization parameters none. Default none. Command mode user exec or any configuration mode. Command default level leve...

  • Page 27

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 22 level: 1. Usage guideline this command displays version information about the switch. Example this example shows how to displays version information about the switch. Switch#show version system mac address: 00-00-00-11-...

  • Page 28

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 23 threshold. The configured range must fall within the operational range which corresponds to the minimum and maximum allowed temperatures defined for the sensor. When the configured threshold is crossed, a notification w...

  • Page 30

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 25 both specifies to enable bidirectional control for the port. In specifies to enable in direction control for the port. Default by default, this option is bidirectional mode. Command mode interface configuration mode. Co...

  • Page 31

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 26 example this example shows how to reset the 802.1x parameters on port 1/0/1. Switch# configure terminal switch(config)# interface ethernet 1/0/1 switch(config-if)# dot1x default switch(config-if)# 3-4 dot1x port-control...

  • Page 32

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 27 this command is used to enable the forwarding of the dot1x pdu. Use the no form of the command to disable the forwarding of the dot1x pdu. Dot1x forward-pdu no dot1x forward-pdu parameters none. Default by default, this...

  • Page 33

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 28 none. Command mode privileged exec mode. Command default level level: 12. Usage guideline under the multi-host mode, specify an interface id to initialize a specific port. Under the multi-auth mode, specify a mac addres...

  • Page 34

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 29 switch(config-if)# dot1x max-req 3 switch(config-if)# 3-8 dot1x pae authenticator this command is used to configure a specific port as an ieee 802.1x port access entity (pae) authenticator. Use the no form of this comma...

  • Page 35

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 30 parameters interface interface-id specifies the port to re-authenticate. Valid interfaces are physical ports. , (optional) specifies a series of interfaces, or separate a range of interfaces from a previous range. No sp...

  • Page 36

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 31 the 802.1x authentication function restricts unauthorized hosts from accessing the network. Use the dot1x system-auth-control command to globally enable the 802.1x authentication control. When 802.1x authentication is e...

  • Page 37

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 32 switch(config-if)# dot1x timeout server-timeout 15 switch(config-if)# dot1x timeout supp-timeout 15 switch(config-if)# dot1x timeout tx-period 10 switch(config-if)# 3-12 show dot1x this command is used to display the ie...

  • Page 38

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 33 port control : auto tx period : 30 sec supp timeout : 30 sec server timeout : 30 sec max-req : 2 times forward pdu : disabled switch# 3-13 show dot1x diagnostics this command is used to display ieee 802.1x diagnostics. ...

  • Page 39

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 34 failswhileauthenticating : 0 reauthswhileauthenticating : 0 eap-startswhileauthenticating : 0 eap-logoffswhileauthenticating : 0 reauthswhileauthenticated : 0 eap-startswhileauthenticated : 0 eap-logoffswhileauthenticat...

  • Page 40

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 35 eth1/0/1 dot1x statistics information: eapol frames rx : 1 eapol frames tx : 4 eapol-start frames rx : 0 eapol-req/id frames tx : 6 eapol-logoff frames rx : 0 eapol-req frames tx : 0 eapol-resp/id frames rx : 0 eapol-re...

  • Page 41

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 36 switch# show dot1x session-statistics interface ethernet 1/0/1 eth6/0/1 session statistic counters are following: sessionoctetsrx : 0 sessionoctetstx : 0 sessionframesrx : 0 sessionframestx : 0 sessionid : sessionauthen...

  • Page 42

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 37 4. Access control list (acl) commands 4-1 access-list resequence this command is used to re-sequence the sequence number of the access list entries in an access list. Use the no form of the command to reset to the defau...

  • Page 43

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 38 20 permit tcp any host 10.100.1.2 30 permit icmp any any switch(config)# ip extended access-list r&d switch(config-ip-ext-acl)# 5 permit tcp any 10.30.0.0 255.255.0.0 switch(config-ip-ext-acl)# exit switch(config)# show...

  • Page 44

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 39 the command with parameter access-group will enable the acl hardware counter for all ports that have applied the specified access-list name or number. The number of packets, that match each rule, are counted. The comman...

  • Page 45

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 40 switch(config)# vlan access-map vlan-map 20 switch(config-access-map)# action redirect ethernet 1/0/5 switch(config-access-map)# end switch# show vlan access-map vlan access-map vlan-map 20 match mac address: ext_mac(id...

  • Page 47

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 42 name specifies the name of the extended expert access-list to be configured. The name can be up to 32 characters. Number (optional) specifies the id number of expert access list. For extended expert access lists, the va...

  • Page 48

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 43 egress direction. Default none. Command mode interface configuration mode. Command default level level: 12. Usage guideline if an ip access group is already configured on the interface, the command applied later will ov...

  • Page 49

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 44 none. Command mode global configuration mode. Command default level level: 12. Usage guideline the name must be unique among all access lists. The characters used in the name are case sensitive. If the access list numbe...

  • Page 50

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 45 only one access list of the same type can be applied to the same interface; but access lists of different types can be applied to the same interface. The association of an access group with an interface will consume the...

  • Page 51

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 46 this example shows how to configure an ipv6 extended access list, named ip6-control. Switch# configure terminal switch(config)# ipv6 access-list extended ip6-control switch(config-ipv6-ext-acl)# permit tcp any 2002:f03:...

  • Page 54

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 49 command mode vlan access-map sub-map configuration mode. Command default level level: 12. Usage guideline use this command to associate an ip access list with the configured sub-map. One sub-map can only be associated w...

  • Page 55

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 50 use this command to associate an ipv6 access list with the configured sub-map. One sub-map can only be associated with one access list (ip access list, ipv6 access list or mac access list). Ipv6 sub-map just checks ipv6...

  • Page 56

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 51 switch(config-access-map)# end switch# show vlan access-map vlan access-map vlan-map 20 match ip address: sp1(id: 3999) action: forward vlan access-map vlan-map 30 match mac address: ext_mac(id: 7999) action: forward sw...

  • Page 57

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 52 inner inner-cos (optional) specifies the inner priority value. This value must be between 0 and 7. Vlan outer-vlan (optional) specifies the outer vlan id. Inner inner-vlan (optional) specifies the inner vlan id. Any spe...

  • Page 58

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 53 icmp-code (optional) specifies the icmp message code. The valid number for the message code is from 0 to 255. Icmp-message (optional) specifies the icmp message. The following pre-defined parameters are available for se...

  • Page 60

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 55 af42 - 100100, af43 - 100110, cs1 - 001000, cs2 - 010000, cs3 - 011000, cs4 - 100000, cs5 - 101000, cs6 - 110000, cs7 - 111000, default - 000000, ef – 101110. Tos tos (optional) specifies that packets can be filtered by...

  • Page 61

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 56 sequence number that is 10 greater than the largest sequence number in that access list and is placed at the end of the list. The user can use the command access-list sequence to change the start sequence number and inc...

  • Page 63

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 58 multicast-listener-query, multicast-listener-done, multicast-listener- report, nd-na, nd-ns, next-header, no-admin, no-route, packet-too-big, parameter-option, parameter-problem, port-unreachable, reassembly- timeout, r...

  • Page 64

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 59 this example shows how to create two entries for an ipv6 standard access-list named “ipv6-std-control”. These entries are: permit ip packets destined to network ff02::0:2/16, and permit ip packets destined to host ff02:...

  • Page 65

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 60 command mode mac access-list configuration mode. Command default level level: 12. Usage guideline if a rule entry is created without a sequence number, a sequence number will be automatically assigned. If it is the firs...

  • Page 66

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 61 usage guideline if interface is not specified, all of the interfaces that have access list configured will be displayed. Example this example shows how to display access lists that are applied to all of the interfaces. ...

  • Page 67

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 62 -------------------------------------- --------------- simple-ip-acl(id: 3998) ip ext-acl simple-rd-acl(id: 3999) ip ext-acl rd-mac-acl(id: 6998) mac ext-acl rd-ip-acl(id: 1998) ip acl ip6-acl(id: 12999) ipv6 ext-acl pa...

  • Page 68

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 63 command mode user exec or any configuration mode. Command default level level: 1. Usage guideline if no access-map name is specified, all vlan access-map information will be displayed. If the user enables the acl hardwa...

  • Page 69

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 64 map-name (optional) specifies the name of the vlan access map. The name can be up to 32 characters. Vlan-id (optional) specifies the vlan id. Default none. Command mode user exec or any configuration mode. Command defau...

  • Page 70

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 65 default none. Command mode global configuration mode. Command default level level: 12. Usage guideline a vlan access map can contain multiple sub-maps. For each sub-map, one access list (ip access list, ipv6 access list...

  • Page 71

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 66 a vlan can only be associated with one vlan access map. Example this example shows how to apply the vlan access-map “vlan-map” in vlan 5. Switch# configure terminal switch(config)# vlan filter vlan-map vlan-list 5 switc...

  • Page 72

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 67 5. Access management commands 5-1 access class this command is used to specify an access list to restrict the access via a line. Use the no form of the command to remove the specified access list check. Access-class ip-...

  • Page 73

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 68 parameters c specifies the separator of the login banner message, for example a pound sign (#). The delimiting character is not allowed in the login banner message. Message specifies the contents of a login banner which...

  • Page 74

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 69 no prompt parameters string specifies a string to define the customized prompt. The prompt will be based on the specified characters or the following control characters. The space character in the string is ignored. % h...

  • Page 75

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 70 switch. The password can contain embedded spaces. The password is case-sensitive. This is the default option. The plain-text password maximum length is 32. (the range is 1-32) 7 password specifies the password in the en...

  • Page 76

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 71 usage guideline this command enables the http server function. The https access interface is separately controlled by ssl commands. Example this example shows how to enable the http server. Switch# configure terminal sw...

  • Page 78

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 73 global configuration mode. Command default level level: 12. Usage guideline this command configures the tcp port number for the http server. Example this example shows how to configure the http tcp port number to 8080. ...

  • Page 79

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 74 ip telnet server no ip telnet server parameters none. Default by default, this option is enabled. Command mode global configuration mode. Command default level level: 12. Usage guideline this command enables or disables...

  • Page 80

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 75 this example shows how to change the telnet service port number to 3000. Switch# configure terminal switch(config)# ip telnet service-port 3000 switch(config)# 5-12 ip telnet source-interface this command is used to spe...

  • Page 81

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 76 console specifies the local console terminal line. Telnet specifies the telnet terminal line ssh specifies the ssh terminal line default none. Command mode global configuration mode. Command default level level: 12. Usa...

  • Page 82

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 77 switch(config)# 5-15 service password encryption this command is used to enable the encryption of the password before stored in the configuration file. The no command will disable the encryption. Service password-encryp...

  • Page 83

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 78 none. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display information about the terminal configuration parameters for the current t...

  • Page 84

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 79 switch# show ip http server ip http server state : enable switch# 5-18 show ip http secure-server this command is used to display information about the ssl feature's status. Show ip http secure-server parameters none. D...

  • Page 85

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 80 user exec or any configuration mode. Command default level level: 1. Usage guideline this command displays information about the active lines on the switch. Example this example shows how to display all session informat...

  • Page 86

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 81 ctrl+_ (press and hold the ctrl and shift keys and the underscore ‘_’ key). The special telnet commands will be displayed as follows: • e – exits the telnet connection. Either an uppercase or lowercase letter ‘e’ can ex...

  • Page 87

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 82 terminal length default number no terminal length default parameters number specifies the number of lines to display on the screen. This value must be between 0 and 512.When the terminal length is 0, the display will no...

  • Page 88

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 83 parameters bps specifies the console rate in bits per second (bps). Default by default, this value is 115200. Command mode global configuration mode. Command default level level: 12. Usage guideline use this command to ...

  • Page 89

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 84 switch(config-line)# session-timeout 0 switch(config-line)# 5-24 terminal width the command is used to set the number of character columns on the terminal screen for the current session line. The terminal width command ...

  • Page 90

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 85 default width: 80 columns baud rate: 9600 switch# terminal width 120 switch# show terminal length: 24 lines width: 120 columns default length: 24 lines default width: 80 columns baud rate: 9600 switch # 5-25 username th...

  • Page 91

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 86 this command creates user accounts with different access levels. When the user login with level 1, the user will be in the user exec mode. The user needs to further use the enable command to enter the privileged exec mo...

  • Page 92

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 87 line configuration mode. Command default level level: 15. Usage guideline this command is used to create a new user password. Only one password can be used for each type of line. Example this example shows how to create...

  • Page 93

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 88 6. Arp spoofing prevention commands 6-1 ip arp spoofing-prevention this command is used to configure an arp spoofing prevention (asp) entry of the gateway used for preventing arp poisoning attacks. Use the no form of th...

  • Page 94

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 89 switch(config)# 6-2 show ip arp spoofing-prevention this command is used to display the configuration of arp spoofing prevention. Show ip arp spoofing-prevention parameters none. Default none. Command mode user exec or ...

  • Page 95: Accounting (Aaa) Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 90 7. Authentication, authorization, and accounting (aaa) commands 7-1 aaa accounting commands this command is used to configure the accounting method list used for all commands at the specified privilege level. Use the no...

  • Page 97

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 92 no aaa accounting network default parameters network specifies to perform accounting of network related service requests. Start-stop specifies to send accounting messages at both the start time and the end time of acces...

  • Page 98

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 93 parameters system specifies to perform accounting for system-level events. Start-stop specifies to send accounting messages at both the start time and the end time of access. Users are allowed to access the network rega...

  • Page 99

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 94 parameters method1 [method2...] specifies the list of methods that the authentication algorithm tries in the given sequence. Enter at least one method or enter up to four methods. The following are keywords that can be ...

  • Page 100

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 95 method. Local – specifies to use the local database for authentication. Group radius – specifies to use the servers defined by the radius server host command. Group group-name – specifies to use the server groups define...

  • Page 101

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 96 group tacacs+ - specifies to use the servers defined by the tacacs+ server host command. Group group-name – specifies to use the server groups defined by the aaa group server command. None - normally, the method is list...

  • Page 102

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 97 method1 [method2...] specifies the list of methods that the authentication algorithm tries in the given sequence. Enter at least one method or enter up to four methods. The following are keywords that can be used to spe...

  • Page 103

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 98 the aaa group server. None - normally, the method is listed as the last method. The user will pass authentication if it is not denied by previous method authentication. Default no aaa authentication method is configured...

  • Page 104

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 99 commands. Also use this command to enter the radius group server configuration mode. Use the server command to associate the radius server hosts with the radius server group. Example this example shows how to create a r...

  • Page 105

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 100 this command is used to enable aaa for the authentication or accounting function. Use the no form of the command to disable the aaa function. Aaa new-model no aaa new-model parameters none. Default by default, this fea...

  • Page 106

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 101 line configuration mode. Command default level level: 15. Usage guideline for accounting via the method list to take effect, enable aaa first by using the aaa new-model command. Create the method list first by using th...

  • Page 107

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 102 switch#configure terminal switch(config)# aaa accounting exec list-1 start-stop group radius switch(config)# line console switch(config-line)# accounting exec list-1 switch(config-line)# 7-15 clear aaa counters servers...

  • Page 108

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 103 switch# 7-16 ip http authentication aaa login-authentication this command is used to specify an aaa authentication method list for the authentication of the http server users. Use the no form of the command to reset to...

  • Page 109

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 104 default specifies to do accounting based on the default method list. Method-list specifies the name of the method list to use. Default by default, this option is disabled. Command mode global configuration mode. Comman...

  • Page 110

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 105 this command can be used to specify the interface whose ip address will be used as the source ip address for sending radius packets. If the source interface is specified in both the global configuration mode and group ...

  • Page 111

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 106 switch(config)# ip tacacs source-interface vlan100 switch(config)# 7-20 ip vrf forwarding (server-group) this command is used to configure the vrf reference of an authentication, authorization, and accounting (aaa) rad...

  • Page 112

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 107 no ipv6 radius source-interface parameters interface-id specifies the interface whose ipv6 address will be used as the source ipv6 address for sending radius packets. Default the ipv6 address of the closest interface w...

  • Page 113

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 108 command default level level: 15. Usage guideline for authentication via the method list to take effect, enable aaa first by using the aaa new-model command. Create the method list first by using the aaa authentication ...

  • Page 114

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 109 interface that is specified in the ip radius-source interface command is used as the ip address in the ip headers of the radius packets. Example this example shows how to configure the ip address 10.0.0.21 has as the r...

  • Page 117

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 112 parameters ip-address specifies the ipv4 address of the authentication server. Default by default, no host is in the server group. Command mode tacacs+ group server configuration mode. Command default level level: 15. ...

  • Page 118

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 113 example this example shows how to display the aaa global state. Switch# show aaa aaa is enabled. Switch# 7-29 tacacs-server host this command is used to create a tacacs+ server host. Use the no form of this command to ...

  • Page 119

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 114 switch(config)# tacacs-server host 172.19.122.3 port 1600 timeout 3 key abcde switch(config)# 7-30 show radius statistics this command is used to display radius statistics for accounting and authentication packets. Sho...

  • Page 120

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 115 round trip time the time interval (in hundredths of a second) between the most recent response and the request that matched it from this radius server. Access requests the number of radius access-request packets sent t...

  • Page 121

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 116 none. Command mode privilege exec mode or and configuration mode. Command default level level: 1. Usage guideline use this command to display statistics counters related to servers. Example this example shows how to di...

  • Page 122: 8.  Basic Ipv4 Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 117 8. Basic ipv4 commands 8-1 arp this command is used to add a static entry in the address resolution protocol (arp) cache. Use the no command to remove a static entry in the arp cache. Arp [vrf vrf-name] ip-address hard...

  • Page 123

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 118 minutes specifies the dynamic entry that will be aged-out if it has no traffic activity within the timeout period. The valid values are from 0 to 65535. If this value is configured as 0, then arp entries will never age...

  • Page 124

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 119 this command is used to delete dynamic entries from the arp table. The user can select to delete all dynamic entries, specific dynamic entries, or all of the dynamic entries that are associated with a specific interfac...

  • Page 125

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 120 switch(config-if)# ip address 192.31.7.17 255.255.255.0 secondary switch(config-if)# ip address 192.31.8.17 255.255.255.0 secondary switch(config-if)# 8-5 ip proxy-arp this command is used to enable the proxy arp optio...

  • Page 126

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 121 by default, this option is disabled. Command mode interface configuration mode. Command default level level: 12,15. Usage guideline use this command to enable the local proxy arp function on an interface. This command ...

  • Page 127

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 122 this command is used to set the mtu value. Use the no form to revert to the default setting. Ip mtu bytes no ip mtu parameters bytes specifies to set the ip mtu value. The range is 512 to 16383 bytes. Default by defaul...

  • Page 128

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 123 default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline used to display a specific arp entry, all arp entries, dynamic entries, or static entries, or entries asso...

  • Page 129

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 124 switch# show arp timeout interface timeout (minutes) ---------------------------------------- vlan100 30 vlan200 40 total entries: 2 switch# 8-11 show ip interface this command is used to display the ip interface infor...

  • Page 130

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 125 interface vlan1 is enabled, link status is up ip address is 10.90.90.90/8 (manual) arp timeout is 240 minutes. Ip mtu is 1500 bytes helper address is not set proxy arp is disabled ip local proxy arp is disabled ip dire...

  • Page 131

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 126 this command only affects the forwarding of ip directed broadcast packets whose destination networks are subnets local to the switch. If the ip directed broadcast option is enabled, then these packets are translated to...

  • Page 133

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 128 prefix-name specifies the name of the prefix with a maximum of 32 characters. The syntax allows characters for general strings, but does not allow spaces. Sub-bits specifies the sub-prefix part and host part of the ipv...

  • Page 134

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 129 switch(config-if)# no ipv6 address dhcp-prefix 0:0:0:2::3/64 9-3 ipv6 address autoconfig this command is used to enable the automatic configuration of the ipv6 address using the stateless auto- configuration. Use the n...

  • Page 135

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 130 ipv6 address ipv6-prefix/prefix-length eui-64 no ipv6 address ipv6-prefix/prefix-length eui-64 parameters ipv6-prefix specifies the ipv6 prefix part for the configured ipv6 address. Prefix-length specifies the length o...

  • Page 136

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 131 interface configuration mode. Command default level level: 12. Usage guideline use this command to configure the interface to use dhcpv6 to get an ipv6 address. When the no ipv6 address dhcp command is used, the previo...

  • Page 137

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 132 switch(config-if)# 9-7 ipv6 hop-limit this command is used to configure the ipv6 hop limit on the switch. Use the no form of this command to revert to the default setting. Ipv6 hop-limit value no ipv6 hop-limit paramet...

  • Page 138

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 133 default by default, the ipv6 mtu value is 1500 bytes. Command mode interface configuration mode. Command default level level: 12. Usage guideline the command is available for layer 3 capable interface configuration. Us...

  • Page 139

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 134 when the neighbor host receives the ra which has flag turned on, the host should use a stateful configuration protocol to obtain ipv6 addresses. Example this example shows how to turn on the ipv6 management configure f...

  • Page 140

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 135 no ipv6 nd prefix ipv6-prefix/prefix-length parameters ipv6-prefix/prefix- length specifies the ipv6 prefix to be created or advertised in the ra on the interface. Valid-lifetime (optional) specifies the valid lifetime...

  • Page 141

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 136 this command is used to configure the ipv6 ra interval for an interface. Use the no form of the command to reset the ra interval to the default setting. Ipv6 nd ra interval max-secs [min-secs] no ipv6 nd ra interval pa...

  • Page 142

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 137 command mode interface configuration mode. Command default level level: 12. Usage guideline the lifetime value in ra instructs the received host the lifetime value for taking the router as the default router. Example t...

  • Page 143

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 138 9-15 ipv6 nd reachable-time this command is used to configure the reachable time used in the nd protocol. Use the no form of the command to revert to the default setting. Ipv6 nd reachable-time milli-seconds no ipv6 nd...

  • Page 144

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 139 in milliseconds. This value must be between 0 and 3600000 milliseconds, in multiples of 1000. Default the default value advertised in ra is 0. The default value used by the router is 1000 (one second). Command mode int...

  • Page 145

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 140 use this command to create a static ipv6 neighbor cache entry on an interface. The static entry will be either in the reachable state, if the interface is up, or in the incomplete state if the interface is down. The re...

  • Page 146

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 141 9-19 show ipv6 interface this command is used to display ipv6 interface information. Show ipv6 interface [interface-id] [brief] parameters interface-id (optional) specifies the interface for display. Brief (optional) s...

  • Page 147

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 142 fe80::201:1ff:fe02:304 vlan2 is up, link status is down fe80::201:1ff:fe02:305 200::2 vlan3 is up, link status is down fe80::201:1ff:fe02:306 total entries: 3 switch# 9-20 show ipv6 neighbors this command is used to di...

  • Page 148

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 143 type d – dynamic learning entry. S – static neighbor entry. State incmp (incomplete) - address resolution is being performed on the entry, but the corresponding neighbor advertisement message has not yet been received....

  • Page 149: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 144 10. Bidirectional forwarding detection (bfd) commands 10-1 bfd enable this command is used to enable the bidirectional forwarding detection (bfd) global state. Use the no command to disable the bfd function globally. B...

  • Page 150

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 145 min_rx value specifies the minimum interval (in milliseconds) between received bfd control packets that this system is capable of supporting. The range is from 50 to 1000. Multiplier value specifies the bfd detection t...

  • Page 151

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 146 usage guideline none. Example this example shows how to change the bfd slow time value. Switch# configure terminal switch(config)# interface vlan1 switch(config-if)# bfd slow-timers 1500 switch(config-if)# 10-4 show bf...

  • Page 152

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 147 total entries: 4 switch# 10-5 show bfd neighbors this command is used to display bfd neighbor information. Show bfd neighbors [details] parameters details (optional) specifies to display bfd neighbor information in mor...

  • Page 153

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 148 ---------------- ------------- ----------- ------------ -------------- ----- 10.0.0.3 system 1 1 100 up local diagnostic : no diagnostic poll bit : not set remote minimum rx interval : 50 ms remote minimum tx interval ...

  • Page 154

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 149 11. Border gateway protocol (bgp) commands 11-1 address-family ipv4 (bgp) this command is used to enter the address family configuration mode to configure the setting specific to the address family. Use the no form of ...

  • Page 155

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 150 11-2 address-family vpnv4 this command is used to enter the ipv4 vpn address family mode. Use the no form of this command to delete the configuration of the vpnv4 address family. Address-family vpnv4 no address-family ...

  • Page 156

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 151 network-number/ subnet-length specifies the network number and the length of the network that bgp will aggregate. The format of network-number/subnet- length can be 10.9.18.2/8. Summary-only (optional) specifies to fil...

  • Page 157

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 152 default by default, this option is disabled. Command mode router configuration mode. Command default level level: 12. Usage guideline this command is used to enable the checking of next hop of the bgp aggregated routes...

  • Page 158

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 153 this example shows how to apply the always-compare-med option to enable the comparison of the multi exit discriminator (med) for paths from neighbors in different autonomous systems. Switch# configure terminal switch(c...

  • Page 159

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 154 11-7 bgp bestpath compare-confed-aspath this command is used to configure a bgp routing process to compare the confederation as path length of the routes received. To return the bgp routing process to the default opera...

  • Page 160

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 155 command mode router configuration mode. Command default level level: 12. Usage guideline by default, the bgp router does not consider router id of the routes when comparing paths that have identical comparing factors. ...

  • Page 161

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 156 11-10 bgp bestpath med missing-as-worst this command is used to configure the router to assign a infinite value the route if missing med. Use the no form of the command to restore the default setting. Bgp bestpath med ...

  • Page 162

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 157 command mode router configuration mode. Command default level level: 12. Usage guideline in a large scale bgp network, route reflection is a mechanism used to reduce the needs of fully mesh of ibgp sessions. With route...

  • Page 163

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 158 in a large scale bgp network, route reflection is a mechanism used to reduce the needs of fully mesh of ibgp sessions. With route reflection, an autonomous system can be partitioned into a number of clusters; each clus...

  • Page 164

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 159 use the bgp confederation identifier command the specify the confederation id, and use the bgp confederation peer command to configure the neighbor session for connection to another sub-as within the same confederation...

  • Page 165

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 160 switch(config-router)# bgp confederation peers 21,22,23 11-15 bgp dampening this command is used to configure the route dampening function. Use the no form of the command to restore the default setting. Bgp dampening [...

  • Page 166

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 161 supposed that half-life is configured as 15 min, reuse is 800, and suppress is 1500. When a route flaps (from up to down), 1000 is added to the penalty of the route. Since the penalty is smaller than the suppress value...

  • Page 167

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 162 switch(config)# router bgp 65534 switch(config-router)# no bgp default ipv4-unicast 11-17 bgp default local-preference this command is used to specify the default local preference value for the router. Use the no comma...

  • Page 168

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 163 parameters none. Default by default, this option is disabled. Command mode router configuration mode. Command default level level: 12. Usage guideline all routers in a local as must have the same setting of this comman...

  • Page 169

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 164 use this command to enforce that the routes received from an ebgp peer must have the peer’s as number as the first as in the as path. This feature is used to avoid the local router from spoofing by a misconfigured peer...

  • Page 171

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 166 default a default router-id will be assigned. If loopback interfaces are not configured, the router id is set to the highest ip address of interfaces. If loopback interfaces are configured, the router id is set to the ...

  • Page 172

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 167 switch(config)# router bgp 100 switch(config-router)# bgp scan-time 30 switch(config-router)# 11-24 clear ip bgp this command is used to reset border gateway protocol (bgp) connections using hard or soft reconfiguratio...

  • Page 173

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 168 to refresh the routing entries in the neighbor peer. If a soft reset is applied to inbound session, the session will not be terminated but the local inbound routing table will be cleared and need to be rebuilt. If soft...

  • Page 174

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 169 ip-address (optional) specifies the routing prefix to clear the dampening information. Mask-length (optional) specifies the mask length for the ip address. Default none. Command mode privileged exec mode. Command defau...

  • Page 175

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 170 soft (optional) specifies to issue a soft reset without tearing down the session. Default none. Command mode privileged exec mode. Command default level level: 12. Usage guideline this command is used to initiate a har...

  • Page 176

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 171 switch# clear ip bgp flap-statistics switch# 11-28 distance bgp this command is used to configure the distance for bgp routes. Use the no form of the command to restore to the default setting. Distance bgp external-dis...

  • Page 178

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 173 no ip community-list expanded community-list-name parameters standard specifies to configure a named standard community list. Expanded specifies to configure a named expanded community list. Community-list-name specifi...

  • Page 179

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 174 this example shows how to configure a rule entry for a community list “mycommlist” that permits routes that from network 10 in autonomous system 50000. Switch# configure terminal switch(config)# ip community-list stand...

  • Page 180

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 175 the extended community attribute is used for implementing policy routing. It is an optional, transitive attribute and facilitates transfer of local policies through different autonomous systems. All the names of the st...

  • Page 181

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 176 list matches the route, then no further check will be done against the remaining entries in the access list. If the matched entry is a permit entry, then the as path access list is matched. If the matched entry is a de...

  • Page 182

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 177 when exact is not specified, to match a community list rule entry, the communities specified in the rule entry must be a subset of the communities specified in the community string of the route. Example this example sh...

  • Page 183

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 178 switch# configure terminal switch(config)# router bgp 65100 switch(config-router)# address-family ipv4 unicast switch(config-router-af)# neighbor 10.4.4.4 activate 11-35 neighbor advertisement-interval this command is ...

  • Page 185

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 180 ip-address specifies the ip address of the neighbor peer. Peer-group-name specifies the name of the bgp peer group. Seconds specifies the minimum interval, in seconds, between the sending of as origination routing upda...

  • Page 186

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 181 the command is used to prevent routing loops between routers within a vpn. In the vpn, the most typical application lies in that the two ce ends have the same as number. Normally, these two ce routers can’t receive the...

  • Page 187

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 182 switch(config)# router bgp 65100 switch(config-router)# address-family ipv4 unicast switch(config-router)# neighbor 10.10.10.10 capability graceful-restart switch(config-router)# 11-40 neighbor capability orf prefix-li...

  • Page 188

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 183 switch(config-router)# neighbor 10.20.40.10 remote-as 65200 switch(config-router)# neighbor 10.20.40.10 prefix-list customer in switch(config-router)# neighbor 10.20.40.10 capability orf prefix-list send router b: swit...

  • Page 189

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 184 switch(config)# router bgp 109 switch(config-router)# network 172.16.0.0 switch(config-router)# neighbor 172.16.2.3 remote-as 200 switch(config-router)# neighbor 172.16.2.3 default-originate 11-42 neighbor description ...

  • Page 190

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 185 parameters ip-address specifies the ip address of the neighbor peer. Peer-group-name specifies the name of the bgp peer group. Ttl (optional) specifies the ttl value used for the bgp session. Default the ebgp peer must...

  • Page 191

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 186 by default, no filter is used. Command mode router configuration mode. Address family configuration mode (ipv4 unicast, vpnv4 and vrf). Command default level level: 12. Usage guideline use this command to enable as pat...

  • Page 192

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 187 terminated when the threshold is exceeded. Default by default, the maximum number of prefix value is 16000. The threshold value is 75 percent. Command mode router configuration mode. Address family configuration mode (...

  • Page 193

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 188 address family configuration mode (ipv4 unicast, vpnv4 and vrf). Command default level level: 12. Usage guideline to advertise a route to an ebgp peer, the bgp router will use the original next hop of the advertised ro...

  • Page 194

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 189 when using this command, the bgp connection will be torn down. After a while, the connection will be rebuilt if both the bgp speakers are configured with the same password. Example this example shows how to set the pas...

  • Page 195

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 190 neighbor ip-address peer-group peer-group-name no neighbor ip-address peer-group peer-group-name parameters ip-address specifies the ip address of the neighbor peer. Peer-group-name specifies the name of the bgp peer g...

  • Page 196

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 191 this command is used to prevent the distribution of the border gateway protocol (bgp) neighbor information as specified in a prefix list, a connectionless network service (clns) filter expression, or a clns filter set....

  • Page 197

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 192 parameters ip-address specifies the ip address of the neighbor. Peer-group-name specifies the name of a bgp peer group. As-number specifies the number of the autonomous system to which the neighbor belongs. The range i...

  • Page 198

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 193 ip-address specifies the ip address of the neighbor. Peer-group-name specifies the name of a bgp peer group. Default this command is disabled by default. Command mode router configuration mode. Address family configura...

  • Page 199

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 194 out specifies that the route map is applied to the paths advertised to the neighbor. Default none. Command mode router configuration mode. Address family configuration (ipv4 unicast, vpnv4 and vrf) mode. Command defaul...

  • Page 200

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 195 command default level level: 12. Usage guideline if a bgp peer group is specified for the command, all the members of the peer group will inherit the setting configured with this command. In a large scale bgp network, ...

  • Page 201

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 196 command default level level: 12. Usage guideline the neighbor send-community command can be specified per address family. When specified in the router configuration mode, the route map is applied to the ipv4 unicast ad...

  • Page 202

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 197 11-57 neighbor soft-reconfiguration this command is used to enable the storing of the route information update from the neighbor peer. Use the no form of the command to disable the storing of the route update informati...

  • Page 203

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 198 parameters ip-address specifies the address of the peer. Peer-group-name specifies the name of the peer group, soo-value specifies that the site-of-origin attribute will be encoded as a route origin extended community....

  • Page 204

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 199 parameters ip-address specifies the ip address of the neighbor. Peer-group-name specifies the name of a bgp peer group. Seconds specifies the minimum interval value that bgp tries another tcp connection. This value mus...

  • Page 205

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 200 holdtime: 180 seconds. Command mode router configuration mode. Address family configuration (vrf) mode. Command default level level: 12. Usage guideline the timers configured for a specific neighbor or peer group overr...

  • Page 206

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 201 this example shows how to show the routes specified by a route map named internal-map being unsuppressed for neighbor 172.16.10.10. Switch# configure terminal switch(config)# router bgp 65100 switch(config-router)# add...

  • Page 207

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 202 11-63 neighbor weight this command is used to specify the weight assigned to the routes that are received from a specific neighbor. Use the no form of this command to revert to the default setting. Neighbor {ip-address...

  • Page 208

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 203 parameters network-number specifies the network number that bgp will advertise. Subnet-length specifies the length of the network or sub-network. Route-map map-name (optional) specifies the identifier of a route map. T...

  • Page 209

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 204 external routes to bgp. Internal - specifies to redistribute only the ospf as-internal routes. External - specifies to redistribute only the ospf as-external routes, including type-1 and type-2 routes. Type-1 - specifi...

  • Page 210

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 205 as-number specifies the number of an autonomous system that identifies the router to other bgp routers. This value must be between 1 and 4294967295. Default no bgp routing process is enabled by default. Command mode gl...

  • Page 211

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 206 route-map configuration mode. Command default level level: 12. Usage guideline the as path length is an important factor, that affects the best path selection. When the as-path is not modified by the route map the loca...

  • Page 212

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 207 level: 12. Usage guideline bgp community exchange is not enabled by default. It is enabled on a per-neighbor basis with the neighbor send-community command. The community will be sent out in the bgp packet only when se...

  • Page 213

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 208 command mode route-map configuration mode. Command default level level: 12. Usage guideline use this command to modify the dampening parameters of routes when match conditions are met. Example this example shows how to...

  • Page 214

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 209 to set the med for a route advertised to a remote ebgp peer, specify the set metric command in a route map and apply the route map to the corresponding peer session. You can verify your settings by entering the show ro...

  • Page 216

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 211 no set weight parameters number specifies the weight for the matched routes. This value must be between 0 and 65535. Default there is no set weight statement. Command mode route-map configuration mode. Command default ...

  • Page 217

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 212 command default level level: 1. Usage guideline use this command to display the configured as-path access-lists. If the access list name is not specified, all as-path access-lists are displayed. Example this example sh...

  • Page 218

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 213 none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline this command is used to display the routing entry information in bgp routing table. If a specific network is speci...

  • Page 219

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 214 network next hop metric locprf weight path *> 89.1.1.0/24 10.1.1.4 0 0 5 i *> 89.1.2.0/24 10.1.1.4 0 0 5 i *> 89.1.3.0/24 10.1.1.4 0 0 5 i *> 89.1.4.0/24 10.1.1.4 0 0 5 i *> 89.1.5.0/24 10.1.1.4 0 0 5 i *> 99.1.1.0/24 ...

  • Page 220

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 215 vpnv4 vrf vrf-name (optional) specifies a vrf name. The length of the vrf name is 12 characters. Network-address (optional) specifies the network address and the sub-network mask. Default none. Command mode user exec o...

  • Page 221

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 216 all (optional) specifies to display all the vpnv4 routing entries. Rd rd-value (optional) specifies to display the vpnv4 routing entries that match the specified rd. Vrf vrf-name (optional) specifies to display the vpn...

  • Page 222

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 217 ? - origin of the path is not clear. Network the ip address of a network. Next hop the ip address of the next router to forward the packet. Metric the value of the inter-autonomous system metric. Locprf the local prefe...

  • Page 223

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 218 command default level level: 1. Usage guideline use this command to display the routes that match the specified community string. If no option is specified for the command, the information for ipv4 unicast address fami...

  • Page 224

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 219 11-79 show ip bgp confederation this command is used to display the confederation configuration of bgp. Show ip bgp confederation parameters none. Default none. Command mode user exec or any configuration mode. Command...

  • Page 225

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 220 vpnv4 (optional) specifies to display the vpnv4 address family routing entries. Unicast specifies to display the unicast routing entries. All (optional) specifies to display all the vpnv4 routing entries. Rd rd-value (...

  • Page 226

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 221 bgp table version the version number of the table. This number is incremented whenever the table changes. Local router id the ip address of the router. Status codes the status of the path. It can be one of the followin...

  • Page 227

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 222 if no option is specified for the command, the information for ipv4 unicast address family will be displayed. Example this example shows how to display the dampened paths. Switch# show ip bgp dampening dampened-paths b...

  • Page 228

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 223 ipv4 (optional) specifies to display the ipv4 address family routing entries. Vpnv4 (optional) specifies to display the vpnv4 address family routing entries. Unicast specifies to display the unicast routing entries. Vr...

  • Page 229

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 224 ? - origin of the path is not clear. Network the ip address of a network entity. From the ip address of the peer that advertised this path. Flaps the number of times the route has flapped. Duration the time since the r...

  • Page 230

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 225 max suppress time : 60 mins unreachable route's half-life : 15 mins switch# 11-84 show ip bgp filter-list this command is used to display routes that conform to a specified as path access list. Show ip bgp [ipv4 unicas...

  • Page 231

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 226 * 172.16.0.0 172.16.72.30 0 108 ? * 172.16.1.0 172.16.72.30 0 108 ? * 172.16.11.0 172.16.72.30 0 108 ? * 172.16.14.0 172.16.72.30 0 108 ? * 172.16.15.0 172.16.72.30 0 108 ? * 172.16.16.0 172.16.72.30 0 108 ? * 172.16.1...

  • Page 235

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 230 last read: 00:00:08, last write: 00:00:08, hold time: 90, keepalive interval: 30 configured hold time: 180, keepalive interval: 60 neighbor capabilities: route refresh: advertised and received (old and new) 4-byte as n...

  • Page 236

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 231 index 2, offset 0, mask 0x4 my peer-group member 5 accepted prefixes, maximum limit 12000 threshold for warning message 75% 1 announced prefixes connections established 1; dropped 0 local host: 10.90.90.90, local port:...

  • Page 237

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 232 specified, all ip addresses will be displayed. Vpnv4 vrf vrf-name (optional) specifies a vrf name. The length of the vrf name is 12 characters. Default none. Command mode user exec or any configuration mode. Command de...

  • Page 238

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 233 command default level level: 1. Usage guideline use this command to display the parameters of bgp. Example this example shows how to display the parameters of bgp. Switch# show ip bgp parameters bgp global state : enab...

  • Page 239

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 234 peer-group-name specifies the name of a border gateway protocol (bgp) peer group. The maximum length is 16 characters. Default none. Command mode exec mode or any configuration. Command default level level: 1. Usage gu...

  • Page 240

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 235 with the vrf. Regexp specifies to display routes matching the as path regular expression. The maximum length is 80 characters. Default none. Command mode exec mode or any configuration. Command default level level: 1. ...

  • Page 241

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 236 command mode exec mode or any configuration. Command default level level: 1. Usage guideline use this command to check the route redistribution configuration about bgp. If no option is specified for the command, the ro...

  • Page 242

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 237 none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display what have been already configured to the local bgp about the route reflection. Example...

  • Page 243

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 238 command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display the bgp information by summary. If no option is specified for the command, the bgp summary i...

  • Page 244

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 239 community-list-name (optional) specifies the community list name. The community list name can be standard or expanded. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usa...

  • Page 245

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 240 use this command to display a specific extended community list or all configured extended community lists. Example this example shows how to display all of the configured ip extended community lists. Switch# show ip ex...

  • Page 246

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 241 11-98 synchronization this command is used to enable the advertisement of a route to an external neighbor by the bgp speaker unless the route is a local router or the bgp speaker has learned the route by igp. Use the n...

  • Page 247

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 242 default keep-alive: 60 seconds. Hold-time: 180 seconds. Command mode router configuration mode. Command default level level: 12. Usage guideline the suggested default value for the keep-alive value is a third of the ho...

  • Page 248

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 243 switch# debug ip bgp switch# 11-101 debug ip bgp fsm-event this command is used to turn on the bgp fsm event debug switch option. Use the no form of this command to turn off the bgp fsm event debug switch option. Debug...

  • Page 250

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 245 command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to turn on the bgp route map debug switch option. When the route map matches the bgp route information, debug informa...

  • Page 251

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 246 prefix-list: orf apply sent route, neighbor , prefix: prefix-list:, apply received route, neighbor , prefix: prefix-list: orf apply sent route, neighbor , prefix: prefix-list: orf apply sent route, neighbor , prefix: 1...

  • Page 252

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 247 1.1.1.2 group1 aggregate next_hop_check : disabled default local pref : 100 default holdtime : 180 default keepalive : 60 scan time : 60 bgp active flags: bgp_cflag_compare_router_id bgp_cflag_aspath_ignore bgp active ...

  • Page 253

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 248 session activity : enabled peer group : my remote as : 1 local as : 1 remote router id : 182.148.0.3 bgp state : established (up for 00:21:48) hold time (configured) : 180 seconds hold time (current used) : 90 seconds ...

  • Page 254

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 249 of vpnv4. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to check the internal status and detailed information of a bgp peer group. Exam...

  • Page 255

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 250 parameters vrf vrf-name (optional) specifies the vrf name. This name can be up to 12 characters long. Default none. Command mode privileged exec mode or any configuration mode/ command default level level: 1. Usage gui...

  • Page 256

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 251 default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to check the internal status and detailed information of bgp route aggregation. Example t...

  • Page 257

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 252 command default level level: 1. Usage guideline use this command to check the internal status and detailed information of bgp route damping. Example this example shows how to display internal detailed information about...

  • Page 258

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 253 11-111 debug ip bgp show interface this command is used to display internal detailed information about the bgp interface. Debug ip bgp show interface parameters none. Default none. Command mode user exec or any configu...

  • Page 259

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 254 none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to check the internal status and detailed information of the bgp timer. Example this example show...

  • Page 260

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 255 usage guideline use this command to check the internal status and detailed information of bgp route redistribution. Example this example shows how to display internal detailed information about bgp route redistribution...

  • Page 262

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 257 12. Bpdu protection commands 12-1 spanning-tree bpdu-protection (global) this command is used to enable the bpdu protection function globally. Use the no form of this command to return to the default setting. Spanning-...

  • Page 263

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 258 parameters drop specifies to drop all received bpdu packets when the interface enters the attacked state. Block specifies to drop all packets (include bpdu and normal packets) when the interface enters the attacked sta...

  • Page 264

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 259 user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display bpdu protection information. If no interface id is specified, all interfaces’ information will be display...

  • Page 265

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 260 parameters none. Default by default, this feature is disabled. Command mode global configuration mode. Command default level level: 12. Usage guideline none. Example this example shows how to enable the sending of snmp...

  • Page 269

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 264 14. Command logging commands 14-1 command logging enable this command is used to enable the command logging function. Use the no form of this command to disable the command logging function. Command logging enable no c...

  • Page 270: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 265 15. Connectivity fault management (cfm) commands 15-1 ais this command is used to configure the parameters of the alarm indication signal (ais) function. To disable the ais function, use the no command. Ais [period per...

  • Page 271

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 266 switch(config-cfm-mep)# ais level 5 switch(config-cfm-mep)# 15-2 alarm-time this command is used to define the time period to control when a fault alarm will be sent since a defect is detected and the time period to co...

  • Page 272

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 267 switch(config-cfm-mep)# alarm-time reset 1000 switch(config-cfm-mep)# 15-3 ccm enable this command is used to enable the cfm continuity check message (ccm) function. To disable this function, use the no command. Ccm en...

  • Page 273

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 268 1sec: one second. 10sec: ten seconds. This is the default value. 1min: one minute. 10min: ten minutes. Default by default, this value is 10 seconds. Command mode cfm ma configuration mode. Command default level level: ...

  • Page 274

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 269 the command is used to define a maintenance domain and enter the maintenance domain configuration mode. Each maintenance domain has unique name amongst all those used or available to a service provider or operator. It ...

  • Page 275

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 270 cfm enable no cfm enable parameters none. Default by default, this option is disabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline this command is used to enable or disab...

  • Page 276

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 271 usage guideline this command is used to start or stop the cfm management lock. This command will result in the mep to send lck pdus to a client level mep. Verify the status of the cfm management lock action by entering...

  • Page 278

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 273 request timed out. Cfm loopback statistics for 00-01-02-03-04-05: packets: sent=4, received=0, lost=4(100% loss). Switch# cfm loopback test remote-mepid 2 mepid 1 ma name op-ma1 domain op-domain1 reply from 00-01-02-03...

  • Page 279

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 274 15-12 cfm mep this command is used to define a maintenance association end-point and enter the cfm mep configuration mode. To delete an mep, use the no command. Cfm mep mepid mep-id ma name ma-name domain domain-name [...

  • Page 280

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 275 15-13 clear cfm counter ccm this command is used to clear ccm counters of all meps. Clear cfm counter ccm parameters none. Default none. Command mode privileged exec mode. Command default level level: 12. Usage guideli...

  • Page 281

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 276 usage guideline this command is used to delete the stored link-trace response data that has been initiated by the specified mep. Example this example shows how to delete received link-trace responses. Switch# clear cfm...

  • Page 283

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 278 parameters period period (optional) specifies the transmitting interval of the lck pdu. It can be 1sec or 1min.The default period is 1 second. Level level (optional) specifies the client level to which the mep sends th...

  • Page 284

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 279 cfm ma configuration mode. Command default level level: 12. Usage guideline this command is used to create an mep id list in a maintenance association. To add an mep id into the list, use the cfm mepid-list add command...

  • Page 285

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 280 the creation of mips on a maintenance domain is useful for tracing the link, mip by mip. It also allows the user to perform a loopback from an mep to an mip. An enumerated value indicates whether the management entity ...

  • Page 286

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 281 example this example shows how to configure a maintenance association mip creation to “auto”. Switch# configure terminal switch(config)# cfm domain op-domain level 2 switch(config-cfm-md)# cfm ma name op-ma1 vlan 2 swi...

  • Page 287

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 282 parameters pdu-priority cos-value specifies that the 802.1p priority is set in the ccm and the ltm messages transmitted by the mep. The range of the value is from 0 to 7. Default by default, the pdu priority is level 7...

  • Page 288

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 283 cfm md configuration mode. Command default level level: 12. Usage guideline this command is used to configure the default transmission of the sender id tlv by mps contained by the md. An enumerated value indicates what...

  • Page 289

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 284 this command is used to configure the transmission of the sender id tlv by mps for an ma. An enumerated value indicates what, if anything, is to be included in the sender id tlv transmitted by mps configured in this ma...

  • Page 290

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 285 show cfm counter ccm parameters none. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline the command is used to display the ccm rx packet counters of all mep...

  • Page 291

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 286 domain-name specifies the maintenance domain name as the identifier. It is a string type of maximum length 22. If not specified, all domains are displayed. Default none. Command mode user exec or any configuration mode...

  • Page 292

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 287 level: 1. Usage guideline this command is used to display the cfm state on the specified physical ports. Example this example shows how to display the cfm state on the specified physical ports. Switch# show cfm interfa...

  • Page 293

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 288 usage guideline this command is used to display the link-trace responses. The maximum link-trace responses a device can hold is 128. Example this example shows how to display the link-trace responses. Switch# show cfm ...

  • Page 294

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 289 command mode user exec or any configuration mode. Command default level level: 1. Usage guideline this command is used to display the cfm maintenance association information. Example this example shows how to display c...

  • Page 295

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 290 command default level level: 1. Usage guideline this command is used to display the meps that have configurations. Example this example shows how to display the meps that have configurations. Switch# show cfm mepid 1 m...

  • Page 296

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 291 some remote mep down: this mep is not receiving ccms from some other mep in its configured list. Error ccm received: this mep is receiving invalid ccms, which may be caused by configuration error. Cross-connect ccm rec...

  • Page 297

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 292 status: some remote mep down ais status: normal lck status: normal domain name: md6 ma name: ma6 mepid: 3 status: some remote mep down ais status: normal lck status: normal switch# display parameters status none: no de...

  • Page 298

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 293 level: 1. Usage guideline this command is used to display the mip ccm database entries. Example this example shows how to display the mip ccm database entries. Switch# show cfm mip ccm vid: 10 mac address: 00-07-00-00-...

  • Page 299

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 294 this example shows how to display all the remote mep information seen by local mep 1. Switch# show cfm remote-mep mepid 1 ma name op-ma domain op-domain remote mepid: 2 mac address: 00-11-22-33-44-02 status: ok rdi: ye...

  • Page 300

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 295 status tlv was present in the last ccm received. Blocked: ordinary data cannot pass freely through the port on which the remote mep resides. Up: ordinary data can pass freely through the port on which the remote mep re...

  • Page 301

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 296 rx and tx packet counters of the specified physical interface. If the rx/tx type is specified, it will display the rx or tx packet counters of all physical interfaces. Example this example shows how to display packet c...

  • Page 302

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 297 15-36 cfm mp-ltr-all this command is used to enable the function where all mps reply to ltrs. To disable this function, use the no command. Cfm mp-ltr-all no cfm mp-ltr-all parameters none. Default by default, this opt...

  • Page 303

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 298 example this example shows how to display the mps reply ltrs configuration. Switch# show cfm mp-ltr-all all mps reply ltrs: disabled switch# 15-38 snmp-server enable traps cfm this command is used to enable the trap st...

  • Page 304

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 299 16. Cpu access control list (acl) commands 16-1 soft-acl filter-map this command is used to create or modify a software acl filter map. This command will enter into the software acl filter map configuration mode. Use t...

  • Page 305

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 300 sequence-number specifies the sequence number of the associated match entry. The range is from 1 to 65535. The lower the number is, the higher the priority of the access list. Name specifies the acl access list name to...

  • Page 306

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 301 interfaces. , (optional) specifies a series of physical interfaces. No space before and after the comma. - (optional) specifies a series of physical interfaces. No space before and after the comma. All specifies that i...

  • Page 307

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 302 16-4 show soft-acl this command is used to display the information of software acl filter maps. Show soft-acl filter-map [name] parameters name (optional) specifies the name of the software acl filter map to be display...

  • Page 309

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 304 lldp 0 0 0 ctp 0 0 0 bgp 0 0 0 dhcp 0 0 0 dhcpv6 0 0 0 erps 0 0 0 oam 0 0 0 igmp 0 0 0 mld 0 0 0 pim-ipv4 0 0 0 pim-ipv6 0 0 0 dvmrp 0 0 0 reserved-ipv4-ipmc 0 0 0 reserved-ipv6-ipmc 0 0 0 unknown-ipv4-ipmc 0 0 0 unkno...

  • Page 310

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 305 usage guideline this command is used to reset all counters for layer 2 or layer 3 control packets that are trapped to the cpu. Example this example shows how to clear all statistics counters. Switch# debug clear cpu po...

  • Page 311: 18.  Debug Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 306 18. Debug commands 18-1 debug enable this command is used to enable the debug message output option. To disable the debug message output option, use the no form of this command. Debug enable no debug enable parameters ...

  • Page 312

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 307 default the default debug output is buffer. Command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to set a specified module’s debug message output to debug to the buffer o...

  • Page 314

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 309 parameters none. Default none. Command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to clear the debug buffer information. Example this example shows how to clear the deb...

  • Page 315

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 310 this command is used to display the content of the debug buffer or utilization information of the debug buffer. Debug show buffer [utilization] parameters utilization (optional) specifies to display the utilization of ...

  • Page 316

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 311 none. Command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to display the information about the debug status and message output of the modules. Example this example shows...

  • Page 317

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 312 switch# debug show error log # debug log: 1 # level: fatal # clock: 10000ms # time : 2013/03/11 13:00:00 ====================== software fatal error ======================= invalid mutex handle : 806d6480 current task ...

  • Page 318

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 313 none. Command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to display technical support information. The technical support information is used to collect the switch’s inf...

  • Page 319

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 314 [port 2013-9-8 09:18:22] [mirror 2013-9-8 09:18:22] ******************* mirror ******************* mirror sw table: state: disable ******************** layer two information ******************** [vlan 2013-9-8 09:18:22...

  • Page 320

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 315 five seconds - 8 % one minute - 8 % five minutes - 13 % process name 5sec 1min 5min ----------------- ------ ------ ------ os_util 96 % 93 % 81 % sys_ctr 9 % 2 % 2 % fan_pooling 4 % 3 % 2 % bcmrx 3 % 3 % 3 % bcml2x.0 2...

  • Page 321

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 316 19. Dhcp auto-configuration commands 19-1 autoconfig enable this command is used to enable the auto-configuration function. Use the no form of the command to disable the auto-configuration function. Autoconfig enable n...

  • Page 322

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 317 default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline this command is used to display the status of the auto-configuration. Example this example shows how to di...

  • Page 323

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 318 20. Dhcp client commands 20-1 ip dhcp client class-id this command is used to specify the vendor class identifier used as the value of option 60 for the dhcp discover message. Use the no form of this command to revert ...

  • Page 324

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 319 no ip dhcp client client-id parameters interface-id specifies the vlan interface, whose hexadecimal mac address will be used as the client id to be sent with the discover message. Default the mac address of the vlan wi...

  • Page 325

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 320 level: 12. Usage guideline use this command to specify the host name string (option 12) to be sent with the dhcp discover message. The specification only applies to the subsequent sending of the dhcp discover messages....

  • Page 326

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 321 switch(config-if)#.

  • Page 327: 21.  Dhcp Relay Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 322 21. Dhcp relay commands 21-1 ip dhcp pool (dhcp relay) this command is used to configure a dhcp relay pool on a dhcp relay agent and enter the dhcp pool configuration mode. Use the no form of this command to delete a d...

  • Page 328

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 323 this command is used to enable the dhcp relay agent to validate and remove the relay agent information option in the received dhcp reply packet. Use the no form of the command to globally disable the check for option 8...

  • Page 329

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 324 none (optional) specifies to disable check for option 82 of the reply packet. Default none. Command mode interface configuration mode. Command default level level: 12. Usage guideline this command only takes effect whe...

  • Page 330

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 325 command mode global configuration mode. Command default level level: 12. Usage guideline when dhcp option 82 is enabled, the dhcp packet received from the client will be inserted with an option 82 field before being re...

  • Page 331

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 326 switch(config)# interface vlan 100 switch(config-if)# ip dhcp relay information option-insert none switch(config-if)# 21-6 ip dhcp relay information policy this command is used to configure the option 82 re-forwarding ...

  • Page 332

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 327 parameters drop specifies to discard the packet that already has the relay option. Keep specifies that the dhcp request packet that already has the relay option is left unchanged and directly relayed to the dhcp server...

  • Page 335

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 330 g. Port id: the port number of each box. H. Circuit id’s sub-option’s second tag: this should be 1. I. Second tag’s length: this should be 6. J. Mac address: the switch’s system mac address. Default the circuit id form...

  • Page 336

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 331 level: 12. Usage guideline when ip dhcp relay information trust option is enabled on an interface, the arriving packets with a giaddr of 0 (this relay agent is the first relay of this dhcp request packet) but with rela...

  • Page 337

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 332 switch# configure terminal switch(config)# no ip dhcp relay information trust-all switch(config)# interface vlan 100 switch(config-if)# ip dhcp relay information trusted switch(config-if)# 21-12 ip dhcp local-relay vla...

  • Page 339

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 334 relay source ip-address subnet-mask no relay source ip-address subnet-mask parameters ip-address specifies the source subnet of client packets. Subnet-mask specifies the network mask of the source subnet. Default none....

  • Page 340

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 335 parameters vrf vrf-name (optional) specifies the target dhcp server ip address associate with a virtual routing and forwarding (vrf) space. Global (optional) specifies that the ip address is selected from the global ad...

  • Page 341

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 336 parameters none. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display the effective setting of the trust relay information option f...

  • Page 342

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 337 before and after the hyphen. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline this command is used to display the interface option format configuration. Ex...

  • Page 343

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 338 command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display relay information options with insert configuration information. Example this example shows ...

  • Page 344

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 339 usage guideline use this command to display the relay information option policy action configuration information. Example this example shows how to display relay information option 82 policy action configuration inform...

  • Page 345

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 340 switch(config)# ip dhcp relay unicast switch(config)# 21-21 ip dhcp relay information option vpnid this command is used to enable or disable the insertion of vpn-related sub-options for an interface during the relay of...

  • Page 346

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 341 21-22 show ip dhcp relay information option vpnid this command is used to display the vpn-related sub-options configuration. Show ip dhcp relay information option vpnid parameters none. Default command mode global conf...

  • Page 347

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 342 22. Dhcp server commands 22-1 address range this command is used to specify an ip address range to be associated with a dhcp class in a dhcp address pool. Use the no form of the command to remove the address range to b...

  • Page 348

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 343 22-2 bootfile this command is used to specify the configuration file or image file for the dhcp client to boot the device. Use the no command to remove the specification of the boot file. Bootfile url no bootfile param...

  • Page 349

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 344 default none. Command mode privileged exec mode. Command default level level: 12. Usage guideline use this command to delete the binding of addresses. If pool is specified but the ip address is specified as *, then all...

  • Page 350

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 345 privileged exec mode. Command default level level: 12. Usage guideline use this command to delete the address from the conflict table. The deleted address will be returned to the address pool and free to be assigned. T...

  • Page 351

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 346 usage guideline use this command to clear all of dhcp statistic counters. Example this example shows how to reset all dhcp counters to zero. Switch# clear ip dhcp server statistics switch# 22-6 class (dhcp relay & serv...

  • Page 352

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 347 switch(config-dhcp-class)# option 82 hex 5678 * switch(config-dhcp-class)# exit switch(config)# ip dhcp pool srv-pool1 switch(config-dhcp-pool)# network 172.28.5.0/24 switch(config-dhcp-pool)# class customer-a switch(c...

  • Page 353

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 348 identifier specifies a dhcp client identifier in hexadecimal notation. Default none. Command mode dhcp pool configuration mode. Command default level level: 12. Usage guideline this command is valid for manual binding ...

  • Page 354

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 349 usage guideline use this command to configure the default routers for the clients. The ip address of the router should be on the same subnet as the client’s subnet. Routers are listed in the order of preference. If def...

  • Page 355

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 350 dns-server ip-address [ip-address2…ip-address8] no dns-server ip-address [ip-address2…ip-address8] parameters ip-address specifies an ip addresses to be used by the dhcp client as the dns server. Ip-address2…ip- addres...

  • Page 356

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 351 command default level level: 12. Usage guideline a binding entry is a mapping between the ip address and the hardware address or the client identifier. By creating a manual binding entry, an ip address is manually assi...

  • Page 357

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 352 use the client-identifier command with the host command to specify the manual binding entry based on client identifier. Use the hardware-address command with the host command to specify the manual binding entry based o...

  • Page 358

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 353 this command is used to exclude a range of ip addresses from being allocated to the client. Use the no form of the command to remove a range of excluded addresses. Ip dhcp excluded-address [vrf vrf-name] start-ip-addre...

  • Page 359

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 354 default by default, this value is 2. Command mode global configuration mode. Command default level level: 12. Usage guideline use this command to specify the number of packets that the dhcp server will send as part of ...

  • Page 360

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 355 example this example shows how to configure the waiting time for a ping reply. Switch# configure terminal switch(config)# ip dhcp ping timeout 800 switch(config)# 22-17 ip dhcp pool (dhcp server) this command is used t...

  • Page 361

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 356 no ip dhcp use class parameters none. Default by default, this option is disabled. Command mode global configuration mode. Command default level level: 12. Usage guideline use this command to specify the dhcp server to...

  • Page 362

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 357 usage guideline use this command to configure the duration of the lease for an ip address that is assigned from the address pool. The least setting will not be inherited from the parent address pool. Example this examp...

  • Page 363

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 358 switch# configure terminal switch(config)# ip dhcp pool pool1 switch(config-dhcp-pool)# netbios-node-type h-node switch(config-dhcp-pool)# 22-21 netbios-name-server this command is used to specify wins name servers for...

  • Page 364

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 359 no next-server parameters ip-address specifies the boot server ip address for the client to get the boot file. Default none. Command mode dhcp pool configuration mode. Command default level level: 12. Usage guideline u...

  • Page 365

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 360 usage guideline use this command in the dhcp pool configuration mode to configure a network for the address pool. The user cannot configure the manual binding entry in the address pool that was configured with the netw...

  • Page 366

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 361 ip ip-address specifies the ip addresses. Up to eight ip addresses can be specified. Default none. Command mode dhcp pool configuration mode. Command default level level: 12. Usage guideline this command configures dhc...

  • Page 367

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 362 this example shows how to specify the dhcp server option 72 (www server option) in the ip format. Two www servers are configured, 172.19.10.1 and 172.19.10.100. Switch# configure terminal switch(config)# ip dhcp pool p...

  • Page 368

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 363 example this example shows how a dhcp class service-a is configured and defined with the dhcp option 60 matching pattern 0x112233 and 0x102030. Another class service-b is configured and defined with the dhcp option 60 ...

  • Page 369

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 364 show ip dhcp binding [vrf vrf-name] [ip-address] parameters vrf-name (optional) specifies the name of the vrf instance. Ip-address (optional) specifies the binding entry to display. If the ip address is not specified, ...

  • Page 370

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 365 this command is used to display the conflict ip addresses while the dhcp server attempts to assign the ip address for a client. Show ip dhcp conflict [vrf vrf-name] [ip-address] parameters vrf-name (optional) specifies...

  • Page 371

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 366 switch# 22-29 show ip dhcp pool this command is used to display information about the dhcp pools. Show ip dhcp pool [name] parameters name (optional) specifies to display information about a specific dhcp pool. If not ...

  • Page 372

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 367 22-30 show ip dhcp server this command is used to display the current status of the dhcp server. Show ip dhcp server parameters none. Default none. Command mode user exec or any configuration mode. Command default leve...

  • Page 373

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 368 default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline this command displays dhcp counters. All counters are cumulative. Example this example shows how to displa...

  • Page 374

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 369 22-32 vrf (dhcp pool) this command is used to associate the address pool with a vrf name. Vrf vrf-name no vrf vrf-name parameters vrf-name specifies the name of the vrf to which the address pool is associated with. Def...

  • Page 375

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 370 23. Dhcp server screening commands 23-1 based-on hardware-address this command is used to add or delete an entry of the dhcp server screen profile. Based-on hardware-address client-hardware-address no based-on hardware...

  • Page 376

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 371 default none. Command mode privileged exec mode. Command default level level: 12. Usage guideline use this command to clear the server screen log buffer. The dhcp server screen log buffer keeps tracks the information o...

  • Page 377

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 372 23-4 ip dhcp snooping server-screen this command is used to enable or disable dhcp server screening. Ip dhcp snooping server-screen [server-ip-address [profile profile-name]] no ip dhcp snooping server-screen [server-i...

  • Page 378

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 373 23-5 ip dhcp snooping server-screen log-buffer this command is used to configure the dhcp server screen log buffer parameter. Use the no form of the command to return to the default setting. Ip dhcp snooping server-scr...

  • Page 379

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 374 command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display the content of the dhcp server screen log buffer. The buffer keeps the information of server...

  • Page 380

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 375 example this example shows how to enable the sending of traps for dhcp server screening. Switch# configure terminal switch(config)# snmp-server enable traps dhcp-server-screen switch(config)#.

  • Page 381

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 376 24. Dhcp snooping commands 24-1 ip dhcp snooping this command is used to globally enable dhcp snooping. Use the no command to disable dhcp snooping. Ip dhcp snooping no ip dhcp snooping parameters none. Default by defa...

  • Page 382

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 377 command mode global configuration mode. Command default level level: 12. Usage guideline the dhcp snooping function validates the dhcp packets when it arrives at the port on the vlan that is enabled for dhcp snooping. ...

  • Page 383

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 378 use this command to store the dhcp binding entry to local flash or remote server. Use the follow methods to store dhcp binding entries: • flash: store the entries to a file in local file system. • tftp: store the entri...

  • Page 384

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 379 clear ip dhcp snooping binding [mac-address] [ip-address] [vlan vlan-id] [interface interface-id] parameters mac-address specifies the mac address to clear. Ip-address specifies the ip address to clear. Vlan vlan-id sp...

  • Page 385

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 380 example this example shows how to renew the dhcp snooping binding database. Switch# renew ip dhcp snooping database tftp: //10.0.0.2/store/dhcp-snp-bind switch# 24-7 ip dhcp snooping binding this command is used to man...

  • Page 386

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 381 24-8 ip dhcp snooping trust this command is used to configure a port as a trusted interface for dhcp snooping. Use the no form of this command to return to the default setting. Ip dhcp snooping trust no ip dhcp snoopin...

  • Page 387

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 382 24-9 ip dhcp snooping limit entries this command is used to configure the number of the dhcp snooping binding entries that an interface can learn. Use the no command to reset the dhcp message entry limit. Ip dhcp snoop...

  • Page 388

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 383 default by default, this option is disabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline when the rate of the dhcp packet exceeds the limitation, the port will be changed...

  • Page 389

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 384 switch(config)# ip dhcp snooping station-move deny switch(config)# 24-12 ip dhcp snooping verify mac-address this command is used to enable the verification that the source mac address in a dhcp packet matches the clie...

  • Page 390

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 385 interfaces from a previous range. No space is allowed before and after the comma. - (optional) specifies a range of interfaces. No space is allowed before and after the hyphen. Default by default, dhcp snooping is disa...

  • Page 391

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 386 usage guideline use this command to display dhcp snooping configuration settings. Example this example shows how to display dhcp snooping configuration settings. Switch# show ip dhcp snooping dhcp snooping is enabled d...

  • Page 392

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 387 level: 1. Usage guideline use this command to display dhcp snooping binding entries. Example this example shows how to display dhcp snooping binding entries. Switch# show ip dhcp snooping binding mac address ip address...

  • Page 393

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 388 switch# this example shows how to display dhcp snooping binding entries by vlan 100. Switch# show ip dhcp snooping binding vlan 100 mac address ip address lease (seconds) type vlan interface ----------------- ---------...

  • Page 394

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 389 default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display dhcp snooping database statistics. Example this example shows how to display d...

  • Page 395

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 390 25. Dhcpv6 client commands 25-1 clear ipv6 dhcp client this command is used to restart the dhcpv6 client on an interface. Clear ipv6 dhcp client interface-id parameters interface-id specifies the vlan interface to rest...

  • Page 396

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 391 by default, this option is disabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline use this command to enable the prefix delegation request through an interface. The interf...

  • Page 397

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 392 command default level level: 1. Usage guideline use this command to display the device’s dhcpv6 duid or use the show ipv6 dhcp interface command to display dhcpv6 related setting for interfaces. If the interface id is ...

  • Page 398: 26.  Dhcpv6 Guard Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 393 26. Dhcpv6 guard commands 26-1 ipv6 dhcp guard policy this command is used to create or modify a dhcpv6 guard policy. This command will enter into the dhcpv6 guard configuration mode. Use the no command to remove the d...

  • Page 399

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 394 server messages are dropped on this port. Server specifies that the attached device is a dhcpv6 server. Dhcpv6 server messages are allowed on this port. Default by default, this option is client. Command mode dhcpv6 gu...

  • Page 400

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 395 example this example shows how to create a dhcpv6 guard policy and matches the ipv6 addresses in the access list named list1. Switch# configure terminal switch(config)# ipv6 dhcp guard policy dhcp_filter1 switch(config...

  • Page 401

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 396 parameters policy-name (optional) specifies the dhcpv6 guard policy name. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline if the policy name is specified,...

  • Page 402

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 397 27. Dhcpv6 relay commands 27-1 ipv6 dhcp relay destination this command is used to enable the dhcp for ipv6 relay service on the interface and specify a destination address to which client messages are forwarded to. Us...

  • Page 403

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 398 this command is used to configure the sub-type of the remote id. Use the no form of this command to revert to the default settings. Ipv6 dhcp relay remote-id format sub-type-name no ipv6 dhcp relay remote-id format par...

  • Page 404

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 399 the command is used to enable the insertion of the dhcpv6 relay agent remote id option function. Example this example shows how to enable the insertion of the dhcpv6 relay agent remote id option. Switch# configure term...

  • Page 406

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 401 command default level level: 1. Usage guideline use this command to display the device’s dhcpv6 duid or use the show ipv6 dhcp interface command to display dhcpv6 related settings and information for the specified vlan...

  • Page 407

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 402 ipv6 dhcp relay remote-id policy : drop format : user-define udf is ascii string “userstring” switch#.

  • Page 408

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 403 28. Dhcpv6 server commands 28-1 address prefix this command is used to specify an address prefix for address assignment. Use the no form of this command to remove the address prefix. Address prefix ipv6-prefix/prefix-l...

  • Page 409

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 404 this command is used to specify an address to be assigned to a specified client. Use the no form of this command to remove the static binding address. Address-assignment ipv6-address client-duid [iaid iaid] [lifetime v...

  • Page 410

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 405 switch(dhcpv6-config)# ipv6 dhcp server pool1 switch(dhcpv6-config)# this example shows how to configure a static binding address entry in an ipv6 dhcp pool named “pool2” with iaid option and associates the ipv6 dhcp p...

  • Page 411

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 406 domain-name domain-name no domain-name domain-name parameters domain-name specifies the domain name. Default none. Command mode dhcpv6 pool configuration mode. Command default level level: 12. Usage guideline use this ...

  • Page 412

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 407 use this command to configure the dns ipv6 server address to be assigned to the requesting dhcpv6 client. Multiple server addresses can be configured by setting this command multiple times. Example this example shows h...

  • Page 413

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 408 ipv6 dhcp pool pool-name no ipv6 dhcp pool pool-name parameters pool-name specifies the name for the address pool. The maximum length is 32 characters. Default none. Command mode global configuration mode. Command defa...

  • Page 414

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 409 default none. Command mode interface configuration mode. Command default level level: 12. Usage guideline this command enables dhcp for ipv6 server service on a specified interface. An ipv6 dhcp pool can be associated ...

  • Page 415

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 410 default none. Command mode global configuration mode. Command default level level: 12. Usage guideline a local ipv6 prefix pool defines a block of prefixes. Define the pool with overlay prefixes with other pools. To mo...

  • Page 416

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 411 none. Command mode dhcpv6 pool configuration mode. Command default level level: 12. Usage guideline use this command to configure a static binding prefix entry to specify the prefix to be dedicatedly delegated to speci...

  • Page 417

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 412 default none. Command mode dhcpv6 pool configuration mode. Command default level level: 12. Usage guideline use this command to specify a local ipv6 prefix pool in a ipv6 dhcp pool to delegate the prefix for clients se...

  • Page 418

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 413 use this command to globally enable the ipv6 dhcp server and relay service on the switch. The configuration changes of the dhcpv6 server cannot take effect in real-time, disable and enable the dhcpv6 server to make the...

  • Page 419

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 414 preference value: 0 hint from client: ignored switch# 28-14 show ipv6 dhcp binding this command is used to display the ipv6 prefix binding entry. Show ipv6 dhcp binding [ipv6-prefix] parameters ipv6-prefix (option) spe...

  • Page 420

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 415 show ipv6 dhcp pool [pool-name] parameters pool-name (optional) specifies the ipv6 dhcp pool to be displayed. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guidel...

  • Page 421

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 416 display parameters dhcpv6 pool the name of the pool. Binding for client 000300010002fca5c01c indicates a static binding for the client with the duid 000300010002fca5c01c. Iapd the collection of prefixes assigned to a c...

  • Page 422

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 417 28-17 show ipv6 local pool this command is used to display the local ipv6 prefix pool configuration information. Show ipv6 local pool [pool-name] parameters pool-name (optional) specifies the local ipv6 prefix pool to ...

  • Page 423

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 418.

  • Page 425

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 420 -5.900 -(--) eth1/0/49 30.090 3.353 channel 1 16.794(++) 0.000 -(--) channel 2 16.794(++) 0.000 -(--) channel 3 16.794(++) 0.000 -(--) channel 4 16.794(++) 0.000 -(--) eth1/0/50 30.090 3.353 16.794(++) 0.000 -(--) eth1...

  • Page 426

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 421 channel 4 16.794(++) switch# 29-2 snmp-server enable traps transceiver-monitoring this command is used to enable the sending of all or individual optical transceiver monitoring snmp notifications. Use the no command to...

  • Page 427

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 422 alarm specifies to shut down a port when alarm events occur. Warning specifies to shut down a port when warning events occur. Default by default, this option is disabled. Command mode interface configuration mode. Comm...

  • Page 428

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 423 default none. Command mode global configuration mode. Command default level level: 12. Usage guideline this configuration is only suitable for sfp/sfp+/qsfp+ port interfaces with optical modules with transceiver-monito...

  • Page 429

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 424 command default level level: 12. Usage guideline this command is available for the physical port interface configuration. A user can use this command to enable or disable optical transceiver monitoring functions for an...

  • Page 430

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 425 global configuration mode. Command default level level: 12. Usage guideline only sfp/sfp+/qsfp+ port interfaces with optical modules, with transceiver monitoring capability, are valid for this configuration. This comma...

  • Page 431

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 426 command default level level: 12. Usage guideline only sfp/sfp+/qsfp+ port interfaces with optical modules, with transceiver monitoring capability, are valid for this configuration. This command configures the rx power ...

  • Page 432

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 427 default none. Command mode global configuration mode. Command default level level: 12. Usage guideline only sfp/sfp+/qsfp+ port interfaces with optical modules, with transceiver monitoring capability, are valid for thi...

  • Page 433

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 428 default none. Command mode global configuration mode. Command default level level: 12. Usage guideline only sfp/sfp+/qsfp+ port interfaces with optical modules, with transceiver monitoring capability, are valid for thi...

  • Page 434: (Dvmrp) Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 429 30. Distance vector multicast routing protocol (dvmrp) commands 30-1 ip dvmrp this command is used to enable dvmrp on the current interface. Use the no form to disable dvmrp on the interface. Ip dvmrp no ip dvmrp param...

  • Page 435

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 430 value of 32 means infinity (unreachable). Default the default metric value is 1. Command mode interface configuration mode. Command default level level: 12. Usage guideline for each source network reported, a route met...

  • Page 436

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 431 switch# configure terminal switch(config)# interface vlan1 switch(config-if)# ip dvmrp neighbor-timeout 60 30-4 ip dvmrp probe-time this command is used to configure the dvmrp probe interval. Use the no form of the com...

  • Page 437

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 432 default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline this command displays distance vector multicast routing protocol (dvmrp) information on interfaces on whic...

  • Page 438

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 433 example this example shows how to display neighbor information. Switch# show ip dvmrp neighbor interface neighbor address generation id exptime --------------- ---------------- ------------- ----------- vlan1 10.10.10....

  • Page 439

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 434 level: 1. Usage guideline this command is used to display dvmrp route information. Example this example shows how to displays route information. Switch# show ip dvmrp route state: h = hold-down source network upstream ...

  • Page 440: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 435 31. D-link license management system (dlms) commands 31-1 install dlms activation-code this command is used to install an activation code on the switch. Install dlms activation-code ac-str [unit unit-id] parameters ac-...

  • Page 441

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 436 31-2 show dlms license this command is used to display the installed dlms license information on the switch. Show dlms license [unit unit-id] parameters unit unit-id (optional) specifies the unit id of the switch in th...

  • Page 442

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 437 license’. Current active license the current license mode. The current active license is the highest level valid license. Current active license specifies the feature options that are enabled on the switch. Ei indicate...

  • Page 443: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 438 32. D-link unidirectional link detection (duld) commands 32-1 duld enable this command is used to enable ethernet oam unidirectional link detection on the specified port. Use the no command to disable the function. Dul...

  • Page 444

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 439 none. Default by default, no shutdown is used. Command mode interface configuration mode. Command default level level: 12. Usage guideline this command is used to configure the ethernet oam unidirectional link detectio...

  • Page 447

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 442 global configuration mode. Command default level level: 12. Usage guideline the system supports the dns caching name server function. When the caching name server function is enabled and ip domain-lookup, the system fo...

  • Page 448

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 443 switch(config)# 33-4 ip domain lookup this command is used to enable the dns to carry out the domain name resolution. Use the no form of this command to disable the dns domain name resolution function. Ip domain lookup...

  • Page 449

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 444 ipv6-address specifies the ipv6 address of the equipment. Default none. Command mode global configuration mode. Command default level level: 12. Usage guideline the host name specified in this command needs to be quali...

  • Page 450

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 445 use this command to configure a dns server. When the system cannot obtain an answer from a dns server, it will attempt the subsequent server until it receives a response. If name servers are already configured, the ser...

  • Page 451

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 446 parameters vrf-name (optional) specifies the name of the vrf instance. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display dns rel...

  • Page 452

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 447 command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display the dns related configuration information. Example this example shows how to display the dns...

  • Page 453

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 448 34. Dos prevention commands 34-1 dos-prevention this command is used to enable and configure the dos prevention mechanism. Use the no form of this command to reset dos prevention to the default setting. Dos-prevention ...

  • Page 454

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 449 • all: all of above types. Note: some functions using the ntp protocol might not function properly when the blat attack dos prevention type is enabled as they use the same port number. Example this example shows how to...

  • Page 455

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 450 dos prevention information dos type state --------------------------------------- -------------- land attack enabled blat attack enabled tcp null disabled tcp xmas disabled tcp syn-fin disabled tcp syn srcport less 102...

  • Page 456

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 451 switch# configure terminal switch(config)# snmp-server enable traps dos-prevention switch(config)#.

  • Page 457

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 452 35. Dynamic arp inspection commands 35-1 arp access-list this command is used to create or modify an arp access list. This command will enter into the arp access-list configuration mode. Use the no command to remove an...

  • Page 458

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 453 privileged exec mode. Command default level level: 12. Usage guideline use this command to clear the arp inspection log buffer. Example this example shows how to clear the inspection log. Switch# clear ip arp inspectio...

  • Page 459

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 454 parameters arp-acl-name specifies the access control list name with a maximum of 32 characters. Vlan vlan-id specifies the vlan associated with the arp access list. , (optional) specifies a series of interfaces, or sep...

  • Page 460

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 455 rate value specifies the maximum number of the arp packets that can be processed. The valid range is from 1 to 150 seconds. Burst interval seconds (optional) specifies the length of the burst duration of the arp packet...

  • Page 461

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 456 usage guideline use the command to configure the maximum entry number of the log buffer. The arp inspection log buffer keeps tracks the information of arp packet. The first packet that is given by check will be sent to...

  • Page 462

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 457 this command is used to specify the additional checks to be performed during an arp inspection check. Use the no form of the command to remove specific additional check. Ip arp inspection validate [src-mac] [dst-mac] [...

  • Page 463

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 458 parameters vlan vlan-id specifies the vlan to enable or disable the arp inspection function. , (optional) specifies a series of interfaces, or separate a range of interfaces from a previous range. No space is allowed b...

  • Page 464

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 459 acl-match specifies the logging criteria for packets that are dropped or permitted based on acl matches. Acl-match permit specifies logging when permitted by the configured acl. Acl-match all specifies logging when per...

  • Page 465

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 460 mask format is the same as ip address. Mac any specifies to match any source mac address. Mac host sender-mac specifies to match a single source mac address. Sender-mac sender-mac- mask specifies to match a group of so...

  • Page 466

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 461 command default level level: 1. Usage guideline this command is used to display the status of dai for a specific range of vlans. Example this example shows how to display the statistics of packets that have been proces...

  • Page 467

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 462 switch# display parameters vlan the vlan id that is enabled for arp inspection. Forwarded the number of arp packets that are forwarded by arp inspection. Dropped the number of arp packets that are dropped by arp inspec...

  • Page 468

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 463 none: acl-matched packets are not logged. Permit: logging when packets are permitted by the configured acl. Deny: logging when packets are dropped by the configured acl. All: acl-matched packets are always logged. Dhcp...

  • Page 469

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 464 rate (pps) the upper limit on the number of incoming packets processed per second. Burst interval the consecutive interval in seconds over which the interface is monitored for the high rate of the arp packets. 35-13 sh...

  • Page 470

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 465 sender mac the logging arp’s sender mac address. Occurrence the counter of logging entries occurred and the last time of logging entry occurred..

  • Page 471: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 466 36. Enhanced transmission selection (ets) commands 36-1 ets willing this command is used to enable the enhanced transmission selection (ets) willing mode for the data center bridging exchange protocol (dcbx) on the spe...

  • Page 474

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 469 37. Error recovery commands 37-1 errdisable recovery this command is used to enable the error recovery for causes and to configure the recovery interval. Use the no command to disable the auto-recovery option or to ret...

  • Page 475

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 470 example this example shows how to set the recovery timer to 200 seconds for port security violation. Switch# configure terminal switch(config)# errdisable recovery cause psecure-violation interval 200 switch(config)# t...

  • Page 476

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 471 --------- ----------------- -------------- port1.4 psecure-violation 179 switch#.

  • Page 477

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 472 38. Ethernet oam commands 38-1 ethernet oam this command is used to enable the ethernet oam function on the specified port. Use the no command to disable the function. Ethernet oam no ethernet oam parameters none. Defa...

  • Page 478

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 473 by default, the ethernet oam mode is active. Command mode interface configuration mode. Command default level level: 12. Usage guideline the following two actions are allowed by ports in the active mode, but disallowed...

  • Page 479

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 474 usage guideline the link monitoring function counts the number of symbol errors that occur during the specified window period. This event is generated if the symbol error count is equal to or greater than the specified...

  • Page 481

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 476 this example shows how to configure interface ethernet 1/0/1 ethernet oam error frame monitor window to 100 deciseconds. Switch# configure terminal switch(config)# interface ethernet 1/0/1 switch(config-if)# ethernet o...

  • Page 482

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 477 example this example shows how to enable notifying an ethernet oam error frame event on interface ethernet 1/0/1. Switch# configure terminal switch(config)# interface ethernet 1/0/1 switch(config-if)# ethernet oam link...

  • Page 483

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 478 threshold number specifies the number of frame errors that must occur for this event to be triggered. The range is 0 to 4294967295. Window number specifies the number of frames over which the threshold is defined. If t...

  • Page 484

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 479 switch# configure terminal switch(config)# interface ethernet 1/0/1 switch(config-if)# ethernet oam link-monitor error-frame-period window 1488100 switch(config-if)# this example shows how to configure interface ethern...

  • Page 485

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 480 ethernet oam remote-failure critical-event no ethernet oam remote-failure critical-event parameters none. Default the ethernet oam critical event will be notified by default. Command mode interface configuration mode. ...

  • Page 486

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 481 command mode privileged exec mode. Command default level level: 12. Usage guideline the command is used to request the remote peer to enter or exit the ethernet oam remote loopback mode. Use the ethernet oam remote-loo...

  • Page 487

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 482 switch# configure terminal switch(config)# interface ethernet 1/0/1 switch(config-if)# ethernet oam received-remote-loopback process switch(config-if)# 38-11 show ethernet oam configuration this command is used to disp...

  • Page 488

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 483 notify state : enabled window : 10 deciseconds threshold : 1 error frame frame period error notify state : enabled window : 14881000 frames threshold : 1 error frame frame seconds error notify state : enabled window : ...

  • Page 489

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 484 admin state : enabled mode : active max oampdu size : 1518 bytes remote loopback : support unidirectional : not support link monitoring : support variable request : not support pdu revision : 1 operation status : opera...

  • Page 490

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 485 flowing in one direction only). Remote loopback it indicates that the oam entity can initiate and respond to loopback commands. Link monitoring it indicates that the oam entity can send and receive event notification o...

  • Page 491

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 486 loopback control oampdu tx : 0 loopback control oampdu rx : 0 variable request oampdu tx : 0 variable request oampdu rx : 0 variable response oampdu tx : 0 variable response oampdu rx : 0 organization specific oampdus ...

  • Page 493

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 488 0 errored frame period records 0 errored frame second records remote event logs: ------------------ 0 errored symbol records 1 errored frame records event index : 3 time stamp : 2013.04.18 10:31 error frame : 5 window ...

  • Page 494

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 489 none. Command mode privileged exec mode. Command default level level: 12. Usage guideline this command is used to clear a port’s ethernet oam event log. Example this example shows how to clear the ethernet oam event lo...

  • Page 495: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 490 39. Ethernet ring protection switching (erps) commands 39-1 description this command is used to specify a string that serves as a description for a g.8032 ethernet ring instance. Description description parameters desc...

  • Page 496

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 491 default none. Command mode global configuration mode. Command default level level: 12. Usage guideline use the ethernet ring g.8032 command to create or modify a g.8032 ring and enter the erp configuration mode. The ri...

  • Page 497

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 492 switch(config-g8032–ring-profile)# 39-4 tcn-propagation this command is used to enable the propagation of topology change notifications from the sub-erp instance to the major instance. Use the no form of this command t...

  • Page 498

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 493 none. Command mode erp instance configuration mode. Command default level level: 12. Usage guideline use this command to assign the aps channel vlan for an erp instance. The aps channel vlan needs to be assigned before...

  • Page 499

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 494 none. Command mode erp instance configuration mode. Command default level level: 12. Usage guideline use this command to configure the vlans to be protected by the erp instance. Example this example shows how to config...

  • Page 500

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 495 use this command to create an erp instance under a physical ring. Deploy multiple instances in the same physical ring topology provide the load balancing capability. The id of erp instances in physical rings of the sys...

  • Page 501

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 496 39-9 sub-ring this command is used to specify the sub-ring default instance of a physical ring default instance. Use the no command to remove the sub-ring default instance of a physical ring default instance. Sub-ring ...

  • Page 502

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 497 command mode erp instance configuration mode. Command default level level: 12. Usage guideline this command is used to configure a sub-ring instance connected to another ring instance. This command is applied on the in...

  • Page 503

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 498 this example shows how to configure the guard timer to 700 milliseconds, hold-off timer to 1, wtr timer to 1 minutes for profile “campus”, and then associate instance 1 and 2 with the profile. Switch# configure termina...

  • Page 504

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 499 example this example shows how to configure the interface ethernet 1/0/1 as the first ring port of the g.8032 ring “major-ring”. Switch# configure terminal switch(config)# ethernet ring g8032 major-ring switch(config-e...

  • Page 505

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 500 39-14 revertive this command is used to restore to the working transport entity, in the case of the clearing of a defect. Use the no form of the command to continue to use the ring protection link (rpl), if it is not f...

  • Page 506

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 501 port0 specifies port 0 as the rpl port. Port1 specifies port 1 as the rpl port. Owner specifies the ring node as the rpl owner node for the configured instance. Neighbor specifies the ring node as the rpl neighbor node...

  • Page 507

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 502 user exec or any configuration mode. Command default level level: 1. Usage guideline this command is used to display information of the erp instance. Example this example shows how to display detailed information of er...

  • Page 508

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 503 switch# this example shows how to display detailed information of the erp physical ring “major-ring”. Switch# show ethernet ring g8032 status major-ring ethernet ring “major-ring” admin port0 : eth1/0/1 admin port1 : e...

  • Page 509

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 504 switch# this example shows how to display detailed information of the erp physical ring’s major-ring instance 1: switch# show ethernet ring g8032 status major-ring instance 1 instance : 1 instance status: deactivated r...

  • Page 510

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 505 r-aps channel the aps channel of the erp instance. Protected vlans service protected vlans of the erp instance. Profile the profile associated with the erp instance. Guard timer the time value for the guard timer of th...

  • Page 511

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 506 in addition to these configurations, the configuration of service protected vlans and rpl related settings are fundamental for operation of an erp instance. Example this example shows how to activate the major ring ins...

  • Page 512

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 507 switch(config-g8032–ring-profile)# timer guard 700 switch(config-g8032–ring-profile)# timer hold-off 1 switch(config-g8032–ring-profile)# timer wtr 1 switch(config-g8032–ring-profile)# 39-19 ring_id this command is use...

  • Page 513

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 508 major-ring specifies an erps ring as a major-ring. Sub-ring specifies an erps ring as a sub-ring. Default by default, the erps ring is a major-ring. Command mode erp configuration mode. Command default level level: 12....

  • Page 514

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 509 switch(config-erp)# instance 1 switch(config-erp-instance)# erps force switch ring_port port0 switch(config-erp-instance)# 39-22 erps manual switch ring_port this command is used to block an erp instance port. Erps man...

  • Page 515

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 510 command mode erp instance configuration mode. Command default level level: 12. Usage guideline a clear command will remove the effects of the force and manual commands. The clear command also provides the following fun...

  • Page 516

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 511 • supports the configuration of the sending of a r-aps pdu destination address with the physical ring’s ring id. Before specifying g.8032v1 for a g.8032v2 device, changing the erps version will lead to the restart of t...

  • Page 518

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 513 usage guideline this command is used to display the expansion module’s information. Example this example shows how to display the expansion module’s information: switch# show module-info unit 1 unit 1 boot-up expansion...

  • Page 519

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 514 2nd port mode:4*10g 3rd port mode:40g 4th port mode:40g 4qxs port mode configuration: 1st port mode:40g 2nd port mode:4*10g 3rd port mode:40g 4th port mode:40g switch#.

  • Page 520: 41.  File System Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 515 41. File system commands 41-1 cd this command is used to change the current directory. Cd [directory-url] parameters directory-url specifies the url of the directory. If not specified, the current directory will be sho...

  • Page 521

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 516 switch# 41-2 delete this command is used to delete a file. Delete file-url parameters file-url specifies the name of the file to be deleted. Default none. Command mode privileged exec mode. Command default level level:...

  • Page 522

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 517 command default level level: 1. Usage guideline if url is not specified, the current directory is used. By default, the current directly is located at the root of the file system located at local flash. The storage med...

  • Page 523

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 518 switch# format /d: all sectors will be erased, proceed? (y/n) [n] y enter volume id (up to 11 characters):profiles format completed. Switch# 41-5 mkdir this command is used to create a directory under the current direc...

  • Page 524

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 519 command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to display the contents of a file in the file system. The command is usually used to display text files. If the conte...

  • Page 525

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 520 a file can be renamed to a file located either within the same directory or to another directory. Example this example shows how to rename file called “doc.1” to “test.Txt”. Switch# rename /c:/doc.1 /c:/test.Txt rename...

  • Page 526

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 521 unit unit-id (optional) specifies the unit id in the stacking system. If not specified, all units are displayed. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage gui...

  • Page 527

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 522 42. Filter database (fdb) commands 42-1 clear mac-address-table this command is used to delete a specific dynamic mac address, all dynamic mac addresses on a particular interface, all dynamic mac addresses on a particu...

  • Page 528

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 523 seconds specifies the aging time in seconds. The valid range is 0 or 10 to 1000000 seconds. Setting the aging time to 0 will disable the mac address table aging out function. Default by default, this value is 300 secon...

  • Page 529

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 524 example this example shows how to enable the destination mac address triggered update function. Switch# configure terminal switch(config)# mac-address-table aging destination-hit switch(config)# 42-4 mac-address-table ...

  • Page 531

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 526 specified interface. Vlan vlan-id specifies the vlan of the entry. The range is 1 to 4094. Interface interface-id specifies the forwarding ports. , (optional) specifies a series of interfaces, or separate a range of in...

  • Page 532

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 527 forwarding table and flood all unregistered multicast packets based on the vlan domain. Filter-unregistered specifies to forward registered packets based on the forwarding table and filter all unregistered multicast pa...

  • Page 533

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 528 level: 1. Usage guideline if the option interface is specified, the unicast entry that has the forwarding interface matches the specified interface will be displayed example this example shows how to display all the ma...

  • Page 534

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 529 show mac-address-table aging-time parameters none. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline this command is used to display the mac address table’s...

  • Page 535

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 530 if the interface is not specified, all existing interfaces will be displayed. Example this example shows how to display the mac address learning status on all physical ports 1 to 10. Switch# show mac-address-table lear...

  • Page 536

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 531 ----------------------- -------------- -------------- eth1/0/1 disabled disabled eth1/0/2 disabled disabled eth1/0/3 disabled disabled eth1/0/4 disabled disabled eth1/0/5 disabled disabled eth1/0/6 disabled disabled et...

  • Page 537

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 532 42-12 show multicast filtering-mode this command is used to display the filtering mode for handling multicast packets that are received on an interface. Show multicast filtering-mode [interface vlan-id] parameters inte...

  • Page 538

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 533 by default, this option is disabled. Command mode global configuration mode. Command default level level: 12. Usage guideline use this command to enable the sending of snmp mac notification traps. Example this example ...

  • Page 539

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 534 switch(config-if)#.

  • Page 541

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 536 command mode global configuration mode. Command default level level: 12. Usage guideline administrators can enable the global gvrp state and individual port’s gvrp state to start gvrp on the port. Example this example ...

  • Page 543

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 538 gvrp vlan create no gvrp vlan create parameters none. Default by default, this option is enabled. Command mode global configuration mode. Command default level level: 12. Usage guideline when dynamic vlan creation is e...

  • Page 544

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 539 comma. - (optional) specifies a range of vlans. No spaces are required before and after the hyphen. Default no vlans are forbidden. Command mode interface configuration mode. Command default level level: 12. Usage guid...

  • Page 545

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 540 leave: 60. Leave-all: 1000. Command mode interface configuration mode. Command default level level: 12. Usage guideline this command is used to configure the gvrp timer value on a port. Example this example shows how t...

  • Page 546

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 541 switch# configure terminal switch(config)# gvrp nni-bpdu-address dot1d switch(config)# 43-9 show gvrp configuration this command is used to display the gvrp settings. Show gvrp configuration [interface [interface-id [,...

  • Page 547

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 542 advertise vlan : 1-4094 forbidden vlan : 3-5 ethernet 1/0/6 gvrp status : enabled join time : 20 centiseconds leave time : 60 centiseconds leave-all time : 1000 centiseconds advertise vlan : 1-3 forbidden vlan : 5-8 sw...

  • Page 548

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 543.

  • Page 549

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 544 44. Gratuitous arp commands 44-1 ip arp gratuitous this command is used to enable the learning of gratuitous arp packets in the arp cache table. To disable arp control, use the no form of this command. Ip arp gratuitou...

  • Page 550

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 545 command default level level: 12. Usage guideline a gratuitous arp request packet is an arp request packet where the source and the destination ip address are both set to the ip address of the sending device and the des...

  • Page 551

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 546 switch# configure terminal switch(config)# ip gratuitous-arps switch(config)# interface vlan100 switch(config-if)# arp gratuitous-send interval 1 switch(config-if)#.

  • Page 552: 45.  Igmp Proxy Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 547 45. Igmp proxy commands 45-1 ip igmp proxy this command is used to enable the igmp proxy function. Use the no form of this command to disable the igmp proxy function. Ip igmp proxy no ip igmp proxy parameters none. Def...

  • Page 553

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 548 none. Command mode interface configuration mode. Command default level level: 12. Usage guideline only one upstream can exist in an igmp proxy device. Example this example shows how to configure interface vlan 3 to act...

  • Page 554

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 549 this command is used to enable designated forwarding on a non-querier igmp proxy downstream interface. Use the no form of this command to disable it. Ip igmp proxy designated-forwarding no ip igmp proxy designated-forw...

  • Page 555

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 550 usage guideline use this command to display upstream interface configurations and downstream interfaces. Example this example shows how to display the igmp proxy configurations on the device. Switch# show ip igmp proxy...

  • Page 556

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 551 45-7 show ip igmp proxy forwarding this command is used to display multicast forwarding entries created by the igmp proxy function. Show ip igmp proxy forwarding [group-address] parameters group-address specifies the i...

  • Page 558

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 553 command mode interface configuration mode. Global configuration mode. Command default level level: 12. Usage guideline in the interface configuration mode, the command is only available for vlan interface configuration...

  • Page 559

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 554 none. Command mode interface configuration mode. Command default level level: 12. Usage guideline use the ip igmp snooping access-group command on the router to restrict the multicast traffic receiver to join to specif...

  • Page 560

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 555 this example shows how to enable igmp snooping fast-leave on vlan 1. Switch# configure terminal switch(config)# vlan 1 switch(config-vlan)# ip igmp snooping fast-leave switch(config-vlan)# 46-5 ip igmp snooping ignore-...

  • Page 561

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 556 parameters seconds specifies the maximum amount of time between group-specific query messages, including those sent in response to leave-group messages. The range of this value is 1 to 25. Default by default, this valu...

  • Page 562

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 557 address field of the access list entry. Vlan-id (optional) specifies a layer 2 vlan on a trunk port and applies the filter to packets that arrive on that vlan. Default by default, there is no limit. Command mode interf...

  • Page 563

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 558 switch(config-if)# no ip igmp snooping limit vlan 1000 switch(config-if)# 46-8 ip igmp snooping mrouter this command is used to configure the specified interface(s) as the multicast router ports or as forbidden to be m...

  • Page 564

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 559 46-9 ip igmp snooping proxy-reporting this command is used to enable the proxy-reporting function. Use the no form of this command to disable the proxy-reporting function. Ip igmp snooping proxy-reporting [source ip-ad...

  • Page 565

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 560 default by default, this option is disabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline this command is only available for vlan interface configuration. The interface mu...

  • Page 566

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 561 this example shows how to configure the igmp snooping query interval to 300 seconds on vlan 1000. Switch# configure terminal switch(config)# vlan 1000 switch(config-vlan)# ip igmp snooping query-interval 300 switch(con...

  • Page 567

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 562 parameters number specifies the version of the igmp general query sent by the igmp snooping querier. Default by default, this value is 3. Command mode interface configuration mode. Command default level level: 12. Usag...

  • Page 568

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 563 usage guideline the command is available for vlan interface configuration, physical port or port-channel interface. The command configures the rate of igmp control packet that can be processed by igmp snooping. Example...

  • Page 569

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 564 ip igmp snooping robustness-variable value no ip igmp snooping robustness-variable parameters value specifies the robustness variable. Default by default, this value is 2. Command mode interface configuration mode. Com...

  • Page 570

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 565 group-address specifies a ip multicast group address. Interface-id (optional) specifies an interface or an interface list. The interface can be a physical interface or a port-channel. , (optional) specifies a series of...

  • Page 571

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 566 command default level level: 12. Usage guideline this command is only available for vlan interface configuration. The report suppression function will suppress the duplicate igmp report or leave packets received in the...

  • Page 572

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 567 switch# configure terminal switch(config)# vlan 1 switch(config-vlan)# ip igmp snooping minimum version 3 switch(config-vlan)# this examples shows how to remove the restriction configured on vlan 1. Switch# configure t...

  • Page 573

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 568 robustness value : 2 last member query interval : 1 seconds proxy reporting : enabled (source 1.2.3.4) rate limit : 0 ignore topology change : disabled total entries: 1 switch# 46-21 show ip igmp snooping groups this c...

  • Page 574

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 569 46-22 show ip igmp snooping filter this command is used to display igmp snooping filter configuration information for all interfaces on the switch or for a specified interface. Show ip igmp snooping filter [interface i...

  • Page 575

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 570 this example shows how to display filter information of ethernet 1/0/3. Switch# show ipv6 igmp snooping filter interface ethernet 1/0/3 eth1/0/3 ： rate limit: 30pps groups/channel limit ：25 (exception list: igmp_filter...

  • Page 578

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 573 characters. Default none. Command mode interface configuration mode. Command default level level: 12. Usage guideline the specified description corresponds to the mib object “ifalias” defined in the rfc 2233. Example t...

  • Page 579

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 574 • l2vlan - specifies the ieee 802.1q layer 2 virtual lan interface. • loopback - specifies the software only interface which always stays in the up status. • null - specifies the null interface. • port-channel - specif...

  • Page 580

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 575 switch# configure terminal switch(config)# no interface loopback2 switch (config)# 47-4 interface range this command is used to enter the interface range configuration mode for multiple interfaces. Interface range inte...

  • Page 581

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 576 interface interface-id specifies that the interface can be a physical port or vlan interfaces. If no interface is specified, counters of all interfaces will be displayed. Default none. Command mode user exec or any con...

  • Page 582

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 577 rxoversizedpkts : 0 rxfragmentpkts : 0 rxjabbers : 0 rxsymbolerrors : 0 rxdroppkts : 0 txcollisions : 0 ifinerrors : 0 ifouterrors : 0 ifindiscards : 0 ifinunknownprotos : 0 ifoutdiscards : 0 txdelayexceededdiscards : ...

  • Page 583

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 578 command mode user exec or any configuration mode. Command default level level: 1. Usage guideline if no interface was specified, all existing interfaces will be displayed. Example this example shows how to display the ...

  • Page 584

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 579 rx bytes: 0, tx bytes: 0 rx rate: 0 packets/sec, tx rate: 0 rx packets: 0, tx packets: 0 rx multicast: 0, rx broadcast: 0 rx crc error: 0, rx undersize: 0 rx oversize: 0, rx fragment: 0 rx jabber: 0, rx dropped pkts: 0...

  • Page 585

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 580 usage guideline this command allows the user to display switch port statistics counters. Example this example shows how to display switch port rx counters on ports 1 to 8. Switch#show interfaces ethernet 1/0/1-8 counte...

  • Page 586

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 581 switch# show interfaces ethernet 1/0/1-8,1/0/14 counters errors port align-err fcs-err rcv-err undersize xmit-err outdiscard --------- ---------- --------- -------- ---------- --------- ----------- eth1/0/1 0 0 0 0 0 0...

  • Page 587

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 582 interface-id (optional) specifies the interface id. If no interface is specified, the connection status of all switch ports will be displayed. , (optional) specifies a series of interfaces, or separate a range of inter...

  • Page 588

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 583 , (optional) specifies a series of interfaces, or separate a range of interfaces from a previous range. No spaces are allowed before and after the comma. - (optional)specifies a range of interfaces. No spaces are allow...

  • Page 589

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 584 after the comma. - (optional)specifies a range of interfaces. No spaces are allowed before and after the hyphen. Gbic specifies to display gbic status information. Default none. Command mode user exec or any configurat...

  • Page 590

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 585 vendor rev: a1 vendor sn: sn1234567891 date code: 121009 received power measurements type: oma transmitter technology: copper cable unequalized max case temp: 70 ℃ compatibility: single mode (sm),10400mbd attenuation a...

  • Page 591

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 586 eth1/1/2 auto negotiation: enabled remote signaling: not detected configure status: configuring capability bits: 10m_half, 10m_full, 100m_half, 100m_full, 1000m_full capability advertised bits: 10m_half, 10m_full, 100m...

  • Page 592

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 587 eth1/0/2 down enabled sales department eth1/0/3 down enabled branch-1 eth1/0/4 down enabled eth1/0/5 down enabled eth1/0/6 down enabled eth1/0/7 down enabled eth1/0/8 down enabled eth1/0/9 down enabled eth1/0/10 down e...

  • Page 593

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 588 the physical port, loopback, vlan, tunnel, and management interfaces are valid for this configuration. This command is also configurable for port channel member ports. The command will cause the port to enter the disab...

  • Page 594: (Is-Is) Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 589 48. Intermediate system to intermediate system (is-is) commands 48-1 address-family ipv6 this command is used to enter the ipv6 address family configuration mode to configure the settings specific to the address family...

  • Page 595

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 590 default by default, this feature is enabled. Command mode router configuration mode. Address family configuration mode. Command default level level: 12. Usage guideline is-is performs consistency checks on hello packet...

  • Page 596

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 591 use this command on all switches in an area to prevent unauthorized switches from injecting false routing information into the link-state database. This password is exchanged as plain text and this is currently the onl...

  • Page 597

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 592 distance distance no distance parameters distance enter the administrative distance to be assigned to is-is routes here. The ipv4 distance range is from 1 to 255 and the ipv6 distance range is from 1 to 254. Default by...

  • Page 598

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 593 by default, no domain password is specified. Command mode router configuration mode. Command default level level: 12. Usage guideline this password is exchanged as plain text and is the only authentication type. This p...

  • Page 599

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 594 48-8 hostname dynamic this command is used enable is-is dynamic hostname mapping. Use the no command to disable dynamic hostname mapping. Hostname dynamic no hostname dynamic parameters none. Default by default, router...

  • Page 600

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 595 none. Default by default, this feature is enabled. Command mode router configuration mode. Command default level level: 12. Usage guideline the is-is protocol definition requires that a received lsp with an incorrect d...

  • Page 601

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 596 this example shows how to enable the is-is routing protocol for ip on interface vlan 1. Switch# configure terminal switch(config)# interface vlan 1 switch(config-if)# ip router isis switch(config-if)# 48-11 ipv6 router...

  • Page 602

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 597 parameters level-1 specifies to perform only level 1 routing. The switch will learn only about destinations inside its area. Level 2 routing is performed by the closest level 1-2 router. Level-1-2 specifies to performs...

  • Page 603

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 598 usage guideline none. Example this example shows how to configure the interface vlan 1 to just send out level 2 hello packets. Switch# configure terminal switch(config)# interface vlan 1 switch(config-if)# ip router is...

  • Page 605

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 600 multiplier specifies the hello multiplier. The range is from 2 to 100. Level-1 (optional) specifies to configure the hello multiplier independently for level 1 adjacencies. Level-2 (optional) specifies to configure the...

  • Page 606

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 601 is-is hello packets are padded to the full maximum transmission unit (mtu) size. Padding is-is hello packets to the full mtu allows early detection of errors that resulted from transmission problems with large frames o...

  • Page 608

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 603 default by default, this feature is disabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline use this command only on broadcast media in a network of only two networking dev...

  • Page 609

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 604 and level-2 keywords. Specifying level-1 or level-2 disables the password only for level 1 or level 2 routing, respectively. Example this example shows how to configure a password for interface vlan 1 at level 1. Switc...

  • Page 610

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 605 48-23 isis retransmit-interval this command is used to configure the time between the retransmission of each link-state packet on a point-to-point link. Use the no command to restore this to the default value. Isis ret...

  • Page 611

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 606 level-1 (optional) specifies that this metric should be used only in the spf calculation for level 1 (intra-area) routing. Level-2 (optional) specifies that this metric should be used only in the spf calculation for le...

  • Page 612

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 607 usage guideline use this command to reduce the rate of lsp generation during periods of instability in the network. This command can help to reduce cpu load on the router and to reduce the number of lsp transmissions t...

  • Page 613

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 608 48-27 max-area-addresses this command is used to configure additional manual addresses for an is-is area. Use the no command to disable the manual addresses. Max-area-addresses number no max-area-addresses parameters n...

  • Page 614

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 609 default by default, this value is 1200 seconds. Command mode router configuration mode. Command default level level: 12. Usage guideline use this command to configure the maximum lifetime value of originated lsps. Exam...

  • Page 615

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 610 example this example shows how to generate and accept only new-style tlvs on level 2. Switch# configure terminal switch(config)# router isis switch(config-router)# metric-style wide level-2 switch(config-router)# 48-30...

  • Page 618

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 613 parameters area-tag (optional) specifies a meaningful name as the tag of a routing process. If it is not specified, the process is referenced with a null tag. The tag name must be unique among all ip router processes f...

  • Page 619

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 614 by default, this is not configured. Command mode router configuration mode. Command default level level: 12. Usage guideline this command is used to force the is-is process to set the overload-bit in its non-pseudo nod...

  • Page 620

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 615 example this example shows how to display the is-is ip routing table. Switch# show ip isis route codes: c - connected, e – external, l1 - is-is level-1, l2 - is-is level-2 ia - is-is inter area, d - discard, e - extern...

  • Page 621

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 616 level: 1. Usage guideline this command is used to display the is-is ipv6 routing table information. Example this example shows how to display the is-is ipv6 routing table information. Switch# show ipv6 isis route codes...

  • Page 622

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 617 exec mode or any configuration mode. Command default level level: 1. Usage guideline this command is used to display the is-is path to the intermediate system for ipv6. Example this example shows how to display the is-...

  • Page 623

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 618 lsp-id (optional) specifies to display the lsp with the specified lspid. Displays the contents of a single lsp by its id number. Default none. Command mode exec mode or any configuration mode. Command default level lev...

  • Page 624

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 619 area-tag (optional) specifies the tag of a routing process. L1 (optional) specifies the abbreviation for the level-1 keyword. L2 (optional) specifies the abbreviation for the level-2 keyword. Level-1 (optional) specifi...

  • Page 625

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 620 level: 1. Usage guideline this command is used to display the is-is interfaces information. Example this example shows how to display the is-is interface vlan 1 information. Switch# show isis interface vlan 1 vlan1 is ...

  • Page 626

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 621 switch# show isis hostname level system id dynamic hostname * 0001.0001.0001 ra 2 0001.0001.0002 rb 2 0001.0001.0003 rc switch# display parameters level the router is type. System id the system id of the router. Dynami...

  • Page 627

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 622 area the is-is instance area tag. System id the system id of the neighbor router. Interface the interface of establishing adjacency with the neighbor router. State the established adjacency status. Type the established...

  • Page 630

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 625 parameters vrf-name specifies the name of the vrf instance. Default none. Command mode router configuration mode. Command default level level: 12. Usage guideline vrf instances must already exist before associate it wi...

  • Page 631

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 626 example this example shows how to turn on the is-is debug function. Switch# debug isis switch# 48-48 debug isis interface this command is used to turn on the is-is interface state debug switch. Use the no command to tu...

  • Page 632

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 627 by default, this function is turned off. Command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to turn on or turn off the is-is neighbor state debug switch. When is-is nei...

  • Page 633

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 628 this command is used to turn on the is-is lsps debug switch. Use the no command to turn off the is-is lsps debug switch. Debug isis lsp no debug isis lsp parameters none. Default by default, this function is turned off...

  • Page 634

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 629 use this command to turn on or turn off the is-is spf debug switch. When is-is processes spf calculation, debug information will print if the is-is debug function is turned on. Use the debug isis command to turn on the...

  • Page 635

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 630 default none. Command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to display the settings of debug flags. Example this example shows how to display the settings of debug...

  • Page 636

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 631 isissysstatlspdbaseoloads: 0 isissysstatmanaddrdropfromareas: 0 isissysstatattmpttoexmaxseqnums: 0 isissysstatseqnumskips: 0 isissysstatownlsppurges: 1 isissysstatidfieldlenmismatches: 0 isissysstatmaxareaaddrmismatche...

  • Page 637

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 632 vlan1: is-is lan level-1 isiscircuitcounterentry: isiscircadjchanges: 2 isiscircnumadj: 1 isiscircinitfails: 0 isiscircrejadjs: 0 isiscircidfieldlenmismatches: 0 isiscircmaxareaaddrmismatches: 0 isiscircauthtypefails: ...

  • Page 638: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 633 49. Internet group management protocol (igmp) commands 49-1 clear ip igmp groups this command is used to clear dynamic group member information obtained from the response messages in the igmp buffer. Clear ip igmp grou...

  • Page 639

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 634 this command is used to disable checking the subscriber’s source ip when an igmp report or leave message is received. Use the no form of this command to reset to the default setting. Ip igmp ignore-subscriber-ip-check ...

  • Page 640

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 635 command default level level: 12. Usage guideline this command is only available for vlan interface configuration. This command only takes effect when the interface has ip address configured. Example this example shows ...

  • Page 641

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 636 switch(config-if)# ip igmp enable switch(config-if)# ip igmp last-member-query-interval 2 switch(config-if)# 49-5 ip igmp query-interval this command is used to configure the interval at which the router sends igmp gen...

  • Page 642

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 637 parameters seconds specifies to configure the maximum response time, in seconds, advertised in igmp queries. The range is form 1 to 25. Default by default, this value is 10 seconds. Command mode interface configuration...

  • Page 643

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 638 the robustness variable provides fine tuning to allow for expected packet loss on an interface. The value of the robustness variable is used in calculating the following igmp message intervals: • group member interval ...

  • Page 644

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 639 49-9 ip igmp ssm-map static this command is used to create a static ssm mapping entry for igmpv1 or igmpv2 hosts. Use the no form of the command to delete an entry. Ip igmp ssm-map static access-list source-address no ...

  • Page 645

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 640 switch(config)# ip access-list channel-2 switch(config-ip-acl)# permit any 232.1.1.2 255.255.255.255 switch(config-ip-acl)# exit switch(config)# ip igmp ssm-map static channel-1 10.1.1.1 switch(config)# ip igmp ssm-map...

  • Page 646

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 641 parameters 1 specifies to configure the switch to run igmp version 1. 2 specifies to configure the switch to run igmp version 2. 3 specifies to configure the switch to run igmp version 3. Default the default igmp versi...

  • Page 647

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 642 command default level level: 1. Usage guideline select to display multicast group information for a specific group or for a specific interface. Example this example shows how to display igmp group information in interf...

  • Page 648

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 643 [n]dt[n]h[n]m[n]s. Expires the time that the entry will be removed if there is no refresh on the entry in the format of [n]dt[n]h[n]m[n]s. Stopped indicates that timing out of this entry is not determined by this expir...

  • Page 649

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 644 subscriber source ip check : enabled total entries: 1 switch# display parameters version the igmp protocol version running on the interface. Querier the querier ip on the interface lan. Subscriber source ip check this ...

  • Page 650

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 645 ssm mapping : enabled group address: 232.1.1.1 source address: 10.1.1.1 switch# display parameters ssm mapping enabled/disabled: indicates that the ssm mapping function is enabled or disabled. Group address the ssm gro...

  • Page 651

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 646 50. Ip multicast (ipmc) commands 50-1 clear ip multicast-statistics this command is used to clear the multicast protocol packet statistics counters. Clear ip multicast-statistics [igmp] [pim] [dvmrp] parameters igmp (o...

  • Page 652

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 647 command mode global configuration mode. Command default level level: 12. Usage guideline this command is used to configure the ip multicast forwarding lookup mode. Example this example shows how to configure the ip mul...

  • Page 655

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 650 50-6 show ip multicast this command is used to display multicast information of the system or any ip interface. Show ip multicast [interface [interface-id]] parameters interface-id (optional) specifies the interface na...

  • Page 657

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 652 outgoing interface flags: w - assert winner timers: uptime/expires (10.10.1.52, 224.0.1.3), 0dt05h29m15s/0dt00h02m59s, flags: st incoming interface: vlan1, rpf neighbor: 10.3.4.5 outgoing interface list: vlan121, forwa...

  • Page 658

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 653 group-addr group- address (optional) specifies the group ip address. Source-addr source- address (optional) specifies the multicast source ip address. Default none. Command mode user exec or any configuration mode. Com...

  • Page 659

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 654 user exec or any configuration mode. Command default level level: 1. Usage guideline this command displays how the ip multicast routing performs rpf. Because the router can find rpf information from multiple routing ta...

  • Page 660

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 655 50-10 show ip multicast-statistics this command is used to display the received and sent multicast packet statistics counters. Show ip multicast-statistics [igmp] [pim] [dvmrp] [interface [interface-id]] parameters int...

  • Page 661

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 656 pim state refresh 0 0 unknown pim 0 0 dvmrp packets counter received sent dvmrp probe 0 0 dvmrp report 0 0 dvmrp prune 0 0 dvmrp graft 0 0 dvmrp graft-ack 0 0 unknown dvmrp 0 0 switch#.

  • Page 662

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 657 51. Ip source guard commands 51-1 ip verify source vlan dhcp-snooping this command is used to enable ip source guard for a port. Use the no form of the command to disable ip source guard. Ip verify source vlan dhcp-sno...

  • Page 665

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 660 mac address ip address lease(sec) type vlan interface ----------------- --------------- ---------- ------------- ----- ---------- 00-01-01-01-01-01 10.1.1.10 infinite static 100 eth1/0/3 total entries: 1 switch# this e...

  • Page 666

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 661 default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display the hardware port acl entries for a port in the hardware table. It indicates t...

  • Page 667

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 662 source entry verification active. Inactive-no-snooping-vlan: no dhcp snooping vlan configured with no ip source entry verification active. Ip address the client’s ip address assigned from the dhcp server or configured ...

  • Page 668: 52.  Ip Tunnel Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 663 52. Ip tunnel commands 52-1 interface tunnel this command is used to create a tunnel and enter the interface configuration mode. Use the no command to remove a tunnel. Interface tunnel tunnel-id no interface tunnel tun...

  • Page 669

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 664 command mode interface configuration mode. Command default level level: 12. Usage guideline the command is only available for tunnel interface configuration. Use these commands to configure the source ip address for a ...

  • Page 670

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 665 level: 12. Usage guideline this command is only available for tunnel interface configuration. Use this command to configure the destination ipv4 or ipv6 address for a tunnel interface. Assign the destination ipv4 addre...

  • Page 671

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 666 is dynamically and automatically determined. There are two types of automatic ipv6 over ipv4 tunnels: 6to4 and isatap. The 6to4 tunnel is mainly used for ipv6 network to network, or host to network communication. The i...

  • Page 672

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 667 this example shows how to display information for tunnel 3. Switch#show interface tunnel3 tunnel3 is enabled, link status is up interface type is tunnel interface description: tunnel mode is ipv6ip tunnel source 20.0.0...

  • Page 673

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 668.

  • Page 675

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 670 this example shows how to ping the host with ipv6 address 2001:238:f8a:77:7c10:41c0:6ddd:ecab. Switch# ping 2001:238:f8a:77:7c10:41c0:6ddd:ecab ping 2001:238:f8a:77:7c10:41c0:6ddd:ecab (2001:238:f8a:77:7c10:41c0:6ddd:e...

  • Page 677

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 672 to identify the next hop, traceroute again sends a udp packet, but this time with a ttl value of 2. The first router decrements the ttl field by 1 and send the datagram to the next router. The second router sees a ttl ...

  • Page 679

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 674 parameters port (optional) specifies the destination port of the udp service to be forwarded or not forwarded. Default common used application protocols are enabled. Command mode global configuration mode. Command defa...

  • Page 680

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 675 none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline this command is used to display udp helper address table. Example this example shows how to display udp helper add...

  • Page 681

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 676 application udp port -------------------- --------------- time service 37 ien-116 name service 42 tacacs 49 dns 53 tftp 69 netbios-ns 137 netbios-ds 138 user app1 200 user app2 2000 user app3 1230 switch #.

  • Page 683

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 678 default by default, this option is disabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline when a port is enabled for impb strict-mode access control, a host can only acces...

  • Page 684

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 679 command default level level: 1. Usage guideline use this command to display the impb configuration or use the show ip ip-mac-port-binding violation command to display the entries blocked because of the impb check viola...

  • Page 685

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 680 command mode global configuration mode. Command default level level: 12. Usage guideline when ip-mac-port binding notifies that state is enabled, the switch will send violation traps if any violation packet is received...

  • Page 686: 55.  Ipmcv6 Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 681 55. Ipmcv6 commands 55-1 ipv6 multicast-routing this command is used to enable ipv6 multicast routing. Use the no form of this command to disable ipv6 multicast routing. Ipv6 multicast-routing no ipv6 multicast-routing...

  • Page 687

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 682 rpf-ipv6address specifies the ipv6 address of the next hop that can be used to reach the specified network. Interface-id specifies the rpf interface for the route. The interface where the rpf neighbor ipv6 address is l...

  • Page 688

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 683 multicast information. If no specific interface id is specified, all interface will be displayed. If the keyword interface is not specified, the state of ipv6 multicast routing will be displayed. Default none. Command ...

  • Page 689

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 684 parameters group-address (optional) specifies the group ipv6 address. Source-address (optional) specifies the multicast source ipv6 address. Summary (optional) specifies to display a one-line, abbreviated summary of ea...

  • Page 690

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 685 vlan20 switch# display parameters flags provides information about the entry. S – sparse. Entry is operating in sparse mode. Timers: uptime/expires “uptime” indicates per interface how long (in day, hours, minutes, and...

  • Page 691

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 686 switch# show ipv6 mroute forwarding-cache (2000:60:1:1::10, ff0e::1:1:1) vlan0060 outgoing interface list: 1/0/1, t2 (2000:60:1:1::10, ff0e::1:1:2) vlan0060 outgoing interface list: 1/0/1, 2/0/2 total entries: 2 switch...

  • Page 692

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 687 mroute indicates the ipv6 prefix of the remote network. Interface specifies the interface of the next router (rpf neighbor) to the remote network. 55-7 show ipv6 rpf this command is used to check reverse path forwardin...

  • Page 693

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 688 rpf route/mask: 2000::1000:0/64 rpf type: static switch# this example shows how to display rpf information for the unicast host with the ipv6 address of 2000::3000:301. Switch# show ipv6 rpf 2000::3000:301 rpf informat...

  • Page 694

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 689 56. Ipv6 snooping commands 56-1 ipv6 snooping policy this command is used to create or modify an ipv6 snooping policy. This command will enter the ipv6 snooping configuration mode. Use the no command to delete an ipv6 ...

  • Page 695

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 690 command mode ipv6 snooping configuration mode. Command default level level: 12. Usage guideline nd snooping is designed for a stateless auto-configuration assigned ipv6 address and manually configured ipv6 address. Bef...

  • Page 696

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 691 switch# configure terminal switch(config)# ipv6 snooping policy policy1 switch(config-ipv6-snooping)# limit address-count 25 switch(config-ipv6-snooping)# 56-4 ipv6 snooping attach-policy this command is used to apply ...

  • Page 697

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 692 parameters none. Default ipv6 snooping is permitting station moves. Command mode global configuration mode. Command default level level: 12. Usage guideline when station move is permitted, the dynamic snooping binding ...

  • Page 698

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 693 snooping policy: test1 protocol: dhcp, ndp limit address count: 30 target vlan: 100,200-210,4000 switch# display parameters protocol the protocol used for snooping. Limit address count the maximum number of this ipv6 s...

  • Page 699

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 694 57. Ipv6 source guard commands 57-1 ipv6 source binding vlan this command is used to add a static entry to the binding table. Use the no form of this command to remove the static binding entry. Ipv6 source binding mac-...

  • Page 700

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 695 policy-name specifies the name of the source guard policy. Default none. Command mode global configuration mode. Command default level level: 12. Usage guideline the command is used to create a source guard policy name...

  • Page 701

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 696 switch(config-source-guard)# 57-4 permit link-local this command is used to allow hardware permitted data traffic send by the link-local address. Use the no form of this command to disable this function permit link-loc...

  • Page 702

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 697 interface configuration mode. Command default level level: 12. Usage guideline when the command is applied to a port, the received ipv6 packet except nd, ra, rs and dhcp messages will perform the address binding check....

  • Page 703

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 698 switch# 57-7 show ipv6 neighbor binding this command is used to display the ipv6 binding table. Show ipv6 neighbor binding [vlan vlan-id] [interface interface-id] [ipv6 ipv6-address] [mac mac-address] parameters vlan-i...

  • Page 704

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 699 codes the codes for the ipv6 snooping owner. D: dhcpv6 snooping. S: static. N: nd snooping. Ipv6 address the ipv6 address of the binding entry. Mac address the mac address of the binding entry. Interface the interface ...

  • Page 705: 58.  Jumbo Frame Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 700 58. Jumbo frame commands 58-1 max-rcv-frame-size this command is used to configure the maximum ethernet frame size allowed. Use the no form of the command to revert to the default setting. Max-rcv-frame-size bytes no m...

  • Page 707

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 702 01-00-0c-cc-cc-cd (optional) specifies to tunnel the protocol packets with this destination da. Default by default, this option is disabled. Command mode interface configuration mode. Command default level level: 12. U...

  • Page 708

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 703 no l2protocol-tunnel cos parameters cos-value specifies the cos value. The values are from 0 to 7. 7 is the highest priority. Default by default, this value is 5. Command mode global configuration mode. Command default...

  • Page 709

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 704 command mode interface configuration mode. Command default level level: 12. Usage guideline the tunneling of the layer 2 protocol packets will consume cpu processing power when encapsulating, decapsulating and forwardi...

  • Page 710

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 705 by the system. When the maximum number of packets is exceeded, the excessive protocol packets are dropped. Use the l2protocol-tunnel global drop-threshold command and the l2protocol-tunnel drop-threshold command in the...

  • Page 711

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 706 this example shows how to specify the maximum number of stp packets that can be processed on that interface in 1 second. Switch# configure terminal switch(config)# interface ethernet 1/0/1 switch(config-if)# l2protocol...

  • Page 712

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 707 switch#.

  • Page 713: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 708 60. Link aggregation control protocol (lacp) commands 60-1 channel-group this command is used to assign an interface to a channel group. Use the no form of the command to remove an interface from a channel-group. Chann...

  • Page 714

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 709 this command is used to configure the port priority. Use the no form of the command to revert the port priority to the default settings. Lacp port-priority priority no lacp port-priority parameters priority specifies t...

  • Page 715

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 710 by default, the lacp timeout mode is short. Command mode interface configuration mode. Command default level level: 12. Usage guideline this command is available for physical port interface configuration. Example this ...

  • Page 716

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 711 switch(config)# lacp system-priority 30000 switch(config)# 60-5 port-channel load-balance this command is used to configure the load balance algorithm that the switch uses to distribute packets across ports in the same...

  • Page 718

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 713 eth1/0/11 sa bndl 32768 11 channel group 2 member ports: 2, maxports = 12, protocol: static lacp port port port flags state priority number -------------------------------------------------- eth1/0/8 n/a bndl n/a n/a e...

  • Page 719

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 714 1 lacp 2 static switch#.

  • Page 721

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 716 all specifies to clear lldp neighboring information for all interfaces. Interface-id specifies the interface’s id. , (optional) specifies a series of physical interfaces. No spaces before and after the comma. - (option...

  • Page 722

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 717 sent. Vlan-name specifies the vlan name tlv to send. The vlan name tlv is an optional tlv that allows an ieee 802.1q-compatible ieee 802 lan station to advertise the assigned name of any vlan with which it is configure...

  • Page 723

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 718 this example shows how to enable advertising port and protocol vlan id tlv. The advertised vlan includes 1 to 3. Switch# configure terminal switch(config)# interface ethernet 1/0/1 switch(config-if)# lldp dot1-tlv-sele...

  • Page 724

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 719 command default level level: 12. Usage guideline if the optional tlvs advertisement state is enabled, they will be encapsulated in lldpdu and sent to other devices. The data center bridging exchange protocol (dcbx) is ...

  • Page 725

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 720 consumption capability of a link when no packets are being sent. Max-frame-size (optional) specifies the maximum frame size tlv to send. The maximum frame size tlv indicates the maximum frame size capability of the imp...

  • Page 726

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 721 when an lldp-med capabilities tlv is detected, the application layer will start the fast start mechanism. This command is used to configure the fast start repeat count which indicates the number of lldp message transmi...

  • Page 728

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 723 switch(config)# interface range ethernet 1/0/1-1/0/2 switch(config-if-range)# no lldp management-address 10.1.1.1 switch(config-if-range)# this example shows how to delete the management address fe80::250:a2ff:febf:a05...

  • Page 729

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 724 when disabling the transmission of the capabilities tlv, lldp-med on the physical interface will be disabled at the same time. In other words, all lldp-med tlvs will not be sent, even when other lldp- med tlvs are enab...

  • Page 730

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 725 lldp reinit seconds no lldp reinit parameters seconds specifies the delay value for lldp initialization on an interface. This value must be between 1 and 10 seconds. Default by default, this value is 2 seconds. Command...

  • Page 731

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 726 use this command to globally enable lldp and then the switch can start to transmit lldp packets and receive and process the lldp packets. However, the transmission and receiving of lldp can be controlled respectively b...

  • Page 733

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 728 lldp transmit no lldp transmit parameters none. Default lldp transmit is enabled on all supported interfaces. Command mode interface configuration mode. Command default level level: 12. Usage guideline this command is ...

  • Page 734

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 729 level: 12. Usage guideline the lldp transmission interval must be greater than or equal to four times of the transmission delay timer. Example this example shows how to configure the transmission delay timer to 8 secon...

  • Page 735

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 730 no snmp-server enable traps lldp [med] parameters med (optional) specifies to enable the lldp-med trap state. Default the lldp and lldp-med trap states are disabled. Command mode global configuration mode. Command defa...

  • Page 736

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 731 example this example shows how to enable the sending of lldp med notifications for ethernet 1/0/1. Switch# configure terminal switch(config)# interface ethernet 1/0/1 switch(config-if)# lldp med notification enable swi...

  • Page 737

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 732 parameters none. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline this command is used to display the lldp system’s global configurations. Example this exa...

  • Page 739

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 734 link aggregation :disabled maximum frame size :disabled energy efficient ethernet :disabled lldp-med organizationally specific tlvs: lldp-med capabilities tlv :disabled lldp-med inventory tlv :disabled lldp-dcbx organi...

  • Page 740

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 735 detail (optional) specifies to display the information in detailed mode. If neither brief nor detail is specified, display the information in the normal mode. Default none. Command mode user exec or any configuration m...

  • Page 741

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 736 auto-negotiation advertised capability : 8000(hex) auto-negotiation operational mau type : 0000(hex) link aggregation : aggregation capability : aggregated aggregation status : not currently in aggregation aggregation ...

  • Page 742

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 737 tc0 : 4 tc1 : 7 tc2 : 11 tc3 : 14 tc4 : 18 tc5 : 21 tc6 : 25 tc7 : 0 ets recommendation traffic selection algorithm tc0 : tsaenhancedtransmission tc1 : tsaenhancedtransmission tc2 : tsaenhancedtransmission tc3 : tsaenh...

  • Page 743

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 738 energy efficient ethernet : (see detail) lldp-med capabilities : (see detail) lldp-dcbx capabilities : (see detail) switch# this example shows how to display local information of port 1 in brief mode. Switch# show lldp...

  • Page 744

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 739 subtype : ipv4 address : 10.90.90.90 if type : ifindex oid : 1.3.6.1.4.1.171.10.118.2 advertising ports : - address 2 : ------------------------------------------------ subtype : ipv4 address : 10.90.90.90 if type : if...

  • Page 745

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 740 this example shows how to display information about neighboring devices learned by lldp on eth4/0/9 in detailed mode. Switch# show lldp neighbor interface eth4/0/9 detail port id : eth4/0/9 ----------------------------...

  • Page 746

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 741 priority : - dscp : - unknown : true tagged : - inventory management : (none) switch# this example shows how to display remote lldp information in the normal mode. Switch# show lldp neighbor interface ethernet 1/0/1 po...

  • Page 747

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 742 protocol id entries count : 2 mac/phy configuration status : (see detail) power via mdi : (see detail) link aggregation : (see detail) maximum frame size : 1536 lldp-med capabilities : (see detail) extended power via m...

  • Page 748

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 743 total entries: 2 switch# 61-26 show lldp traffic this command is used to display the system’s global lldp traffic information. Show lldp traffic parameters none. Default none. Command mode user exec or any configuratio...

  • Page 750

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 745 total receives the total number of lldp packets received on the port. Total tlv discards the number of tlvs discarded. Total tlv unknowns the total number of lldp tlvs received on the port where the type value is in th...

  • Page 751

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 746 62. Loopback detection (lbd) commands 62-1 loopback-detection (global) this command is used to enable the loopback detection function globally. Use the no form of the command to disable the function globally. Loopback-...

  • Page 752

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 747 the vlan being blocked on a port can be automatically recovered, if the errdisable recovery cause loopback-detect command is configured. Alternatively, manually recover the operation by entering the shutdown command fo...

  • Page 753

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 748 no loopback-detection interval parameters interval seconds specifies the interval in seconds at which lbd packets are transmitted. The valid range is from 1 to 32767. Default by default, this value is 10 seconds. Comma...

  • Page 754

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 749 use this command to configure the list of vlans that are enabled for loop detection. The command setting takes effect when the port’s loop detection mode is operated in the vlan-based mode. If the vlan id list is empty...

  • Page 755

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 750 -------------- -------- ----------------- --------------- eth1/0/1 disabled normal - eth1/0/2 disabled normal - eth1/0/3 disabled normal - eth1/0/4 enabled loop on vlan 2 120 eth1/0/5 disabled normal - eth1/0/6 disable...

  • Page 756

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 751 snmp-server enable traps loopback-detection no snmp-server enable traps loopback-detection parameters none. Default by default, this feature is disabled. Command mode global configuration mode. Command default level le...

  • Page 757

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 752 63. Mac authentication commands 63-1 mac-auth system-auth-control this command is used to enable mac authentication globally. Use the no form of the command to disable the mac authentication globally. Mac-auth system-a...

  • Page 758

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 753 interface configuration mode. Command default level level: 12. Usage guideline this command is only available for physical port interface configuration. It can be used to enable mac authentication on the specified inte...

  • Page 759

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 754 on the mac address. The mac addresses format can be configured with the authentication mac username format command. Example this example shows how to configure the password for mac authentication. Switch# configure ter...

  • Page 760

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 755 no snmp-server enable traps mac-auth parameters none. Default by default, this feature is disabled. Command mode global configuration mode, command default level level: 12. Usage guideline none. Example this example sh...

  • Page 761: 64.  Mirror Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 756 64. Mirror commands 64-1 monitor session destination interface this command is used to configure the destination interface for a monitor session, allowing packets on source ports to be monitored via a destination port....

  • Page 762

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 757 this command is used to configure the rspan vlan and destination port for an rspan source session. Use the no form of the command to remove the configuration of the rspan vlan. Monitor session session-number destinatio...

  • Page 763

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 758 this example shows how to create an rspan session on the source switch. It assigns vlan 100 as the rspan vlan with the destination interface ethernet 1/0/6 and three source ports (ethernet 1/0/2, ethernet 1/0/3 and eth...

  • Page 764

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 759 for a monitor session, multiple source interfaces can be specified, but only one destination interface can be specified. An interface cannot be a source interface of one session and destination port of another session ...

  • Page 765

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 760 switch(config)# monitor session 2 destination interface ethernet 1/0/1 switch(config)# monitor session 2 source acl mac-monitored-flow switch(config)# 64-5 monitor session source remote vlan this command is used to con...

  • Page 766

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 761 switch(config-if)# switchport access vlan 100 switch(config-if)# exit switch(config)# monitor session 2 source remote vlan 100 switch(config)# monitor session 2 destination interface ethernet 1/0/4 switch(config)# 64-6...

  • Page 767

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 762 64-7 remote-span this command is used to specify a vlan as an rspan vlan. Use the no form of the command to revert to a non-rspan vlan. Remote-span no remote-span parameters none. Default by default, 802.1q vlan is use...

  • Page 768

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 763 no monitor session session-number parameters session-number specifies the session number of the monitor session to be deleted. The valid range is from 1 to 4. Default none. Command mode global configuration mode. Comma...

  • Page 769

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 764 this example shows how to display a created port monitor session with the session number 1. Switch# show monitor session 1 session 1 session type: local session destination port: ethernet 1/0/1 source ports: both: ethe...

  • Page 770: 65.  Mld Proxy Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 765 65. Mld proxy commands 65-1 ipv6 mld proxy this command is used to enable the mld proxy function. Use the no form of this command to disable the mld proxy function. Ipv6 mld proxy no ipv6 mld proxy parameters none. Def...

  • Page 771

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 766 none. Command mode interface configuration mode. Command default level level: 12. Usage guideline this command only takes effect when the interface has an ipv6 address configured. Only one upstream can exist in an mld ...

  • Page 772

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 767 65-4 ipv6 mld proxy designated-forwarding this command is used to enable designated forwarding on a non-querier mld proxy downstream interface. Use the no form of this command to disable it. Ipv6 mld proxy designated-f...

  • Page 773

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 768 command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display the upstream interface configurations and downstream interfaces. Example this example shows ...

  • Page 774

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 769 total entries: 2 switch# this example shows how to display detailed information of group ff1e::330e:32. Switch# show ipv6 mld proxy group ff1e::330e:32 ff1e::330e:32, include source list: 100::1 total entries: 1 switch...

  • Page 775

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 770 switch# this example shows how to display detailed information of the group ff1e::330e:32. Switch# show ipv6 mld proxy forwarding ff1e::330e:32 ff1e::330e:32, 2000::2, vlan52 outgoing interface: vlan20, vlan30 total en...

  • Page 777

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 772 command mode interface configuration mode. Global configuration mode. Command default level level: 12. Usage guideline for a vlan to operate with mld snooping, both the global state and per interface state must be enab...

  • Page 778

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 773 usage guideline the command is only available for vlan interface configuration. The ipv6 mld snooping fast-leave command allows mld membership to be removed from a port right on receiving the leave message without usin...

  • Page 779

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 774 this command is used to configure the interval at which the mld snooping querier sends mld group- specific or group-source-specific (channel) query messages. Use the no form of the command to revert to default setting....

  • Page 780

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 775 forbidden interface specifies a range of interfaces as being not connected to multicast- enabled routers. Interface-id specifies an interface or an interface list. No space is allowed before and after the comma. The in...

  • Page 781

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 776 ipv6-address (optional) specifies the source ip address of proxy reporting. Default by default, this option is disabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline the c...

  • Page 782

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 777 if the system can play the querier role, the entity will listen for mld query packets sent by other devices. If mld query message is received, the device with lower value of ipv6 address becomes the querier. If mld pro...

  • Page 783

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 778 ipv6 mld snooping query-max-response-time seconds no ipv6 mld snooping query-max-response-time parameters seconds specifies to set the maximum response time, in seconds, advertised in mld snooping queries. Default by d...

  • Page 784

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 779 interface configuration mode. Command default level level: 12. Usage guideline the command is only available for vlan interface configuration. Example this example shows how to configure the query version to be 1 on vl...

  • Page 785

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 780 66-13 ipv6 mld snooping report-suppression this command is used to enable mld report suppression on a vlan. To disable report suppression on a vlan, use the no form of this command. Ipv6 mld snooping report-suppression...

  • Page 786

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 781 command mode interface configuration mode. Command default level level: 12. Usage guideline the command is only available for vlan interface configuration the robustness variable provides fine-tuning to allow for expec...

  • Page 787

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 782 level: 12. Usage guideline the command is only available for vlan interface configuration. This command applies to mld snooping on a vlan interface to statically add group membership entries and/or source records. The ...

  • Page 788

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 783 66-17 ipv6 mld snooping minimum-version this command is used to configure the minimum version of mld hosts which mld that is allowed on the interface. Use the no form of this command to remove the restriction from the ...

  • Page 789

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 784 usage guideline use this command to display mld snooping information for all vlans on which mld snooping are enabled by not specifying specific vlan. Example this example shows how to display mld snooping configuration...

  • Page 790

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 785 command default level level: 1. Usage guideline use this command to display mld snooping limit and access group information by command. Example this example shows how to display filter information when no interface is ...

  • Page 791

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 786 none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display mld group information by command. Example this example shows how to display mld snoopi...

  • Page 792

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 787 this example shows how to display mld snooping multicast router information. Switch# show ipv6 mld snooping mrouter vlan ports -------- ------------------------------------------------------------------- 1 eth1/0/4 (st...

  • Page 793

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 788 interface eth4/0/4 rx: v1report 3, v2report 0, query 3, v1done 0 tx: v1report 2, v2report 2, query 1, v1done 2 total entries: 3 switch# show ipv6 mld snooping statistics vlan 1 vlan 1 statistics: rx: v1report 3, v2repo...

  • Page 794: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 789 67. Multicast listener discovery (mld) commands 67-1 ipv6 mld enable this command is used to enable the mld protocol state. Use the no form of this command to disable the mld protocol state. Ipv6 mld enable no ipv6 mld...

  • Page 795

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 790 default by default, this value is 2. Command mode interface configuration mode. Command default level level: 12. Usage guideline this command is only available for vlan interface configuration. The user can use this co...

  • Page 796

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 791 example this example shows how to configure the interval of the last listener query to 2 seconds on vlan 1000. Switch# configure terminal switch(config)# interface vlan1000 switch(config-if)# ipv6 mld last-listener-que...

  • Page 797

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 792 ipv6 mld query-max-response-time seconds no ipv6 mld query-max-response-time parameters seconds specifies to set the maximum response time, in seconds, advertised in mld queries. The range is from 1 to 25. Default by d...

  • Page 798

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 793 usage guideline the command is only available for the vlan interface configuration. The robustness variable provides fine-tuning to allow for expected packet loss on an interface. The value of the robustness variable i...

  • Page 799

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 794 67-8 ipv6 mld ssm-map static this command is used to configure static source specific multicast (ssm) mappings. To disable this feature, use the no command. Ipv6 mld ssm-map static access-list source-address no ipv6 ml...

  • Page 801

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 796 user exec or any configuration mode. Command default level level: 1. Usage guideline this command is used to display multicast group information for a specific group or for a specific interface. Example this example sh...

  • Page 802

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 797 last reporter last host to report being a member of the multicast group. 67-11 show ipv6 mld interface this command is used to display mld information on the switch. Show ipv6 mld interface [interface-id] parameters in...

  • Page 803

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 798 67-12 show ipv6 mld ssm-map this command is used to display source specific multicast (ssm) mapping information. Show ipv6 mld ssm-map group-address parameters group-address default none. Command mode user exec or any ...

  • Page 804: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 799 68. Multicast source discovery protocol (msdp) commands 68-1 ip msdp this command is used to enable the msdp function. To disable this function, use the no command. Ip msdp no ip msdp parameters none. Default by defaul...

  • Page 805

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 800 command mode global configuration mode. Command default level level: 12. Usage guideline a larger connect retry time interval will delay the time before attempting to re-establish the peer session. For best results, co...

  • Page 806

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 801 68-4 ip msdp sa-cache-time this command is used to configure the expiry time for source-active cache entries. Use the no command to revert this to the default setting. Ip msdp sa-cache-time seconds no ip msdp sa-cache-...

  • Page 807

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 802 by default, no msdp peer exists. Command mode global configuration mode. Command default level level: 12. Usage guideline the msdp peer is specified by ip address. Example this example shows how to create an msdp peer ...

  • Page 808

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 803 68-7 ip msdp peer shutdown this command is used to shut down the tcp connection between two peers. Use the no command to configure the msdp peer to the no shutdown state. Ip msdp peer shutdown peer-address no ip msdp p...

  • Page 809

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 804 global configuration mode. Command default level level: 12. Usage guideline md5 authentication must be configured with the same password on both msdp peers. Otherwise, the connection between them cannot be established....

  • Page 810

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 805 68-10 ip msdp peer hold-time this command is used to configure the interval at which an msdp peer will wait for keep-alive messages from other peers before declaring them down. Use the no command to configure the inter...

  • Page 811

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 806 list access-list-name specifies the name of the standard ip access list that defines (s, g) pairs. Default by default, the source-active message incoming filter is not configured. Command mode global configuration mode...

  • Page 812

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 807 by configuring ip msdp sa-filter-out with a list, the router only forwards source-active messages that match (s, g) pairs defined in the standard ip access list to a specified peer. Example this example shows how to co...

  • Page 813

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 808 ip msdp peer minimum-ttl peer-address ttl no ip msdp peer minimum-ttl peer-address parameters peer-address specifies the msdp peer ip address. Ttl specifies the minimum ttl value for data-encapsulated source-active mes...

  • Page 814

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 809 command mode global configuration mode. Command default level level: 12. Usage guideline when the maximum number of source-active cache entries is configured to zero, the switch cannot learn a source-active cache entry...

  • Page 815

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 810 this example shows how to configure an msdp peer 10.1.1.1 as the static rpf peer. Switch# configure terminal switch(config)# ip msdp static-rpf 10.1.1.1 rp-list rplist1 switch(config)# 68-17 ip msdp mesh-group this com...

  • Page 816

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 811 default none. Command mode privileged exec mode. Command default level level: 12. Usage guideline this command also will clear all msdp statistic counters. If the msdp peer address is not specified, the tcp connections...

  • Page 817

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 812 clear ip msdp sa-cache [group-address] parameters group-address (optional) specifies the group address of the source-active cache entry. Default none. Command mode privileged exec mode. Command default level level: 12....

  • Page 818

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 813 connect retry interval: 30 sa cache expiry time: 210 sa originating filter: configured, list: source1 switch# 68-22 show ip msdp peer this command is used to display msdp peer information. Show ip msdp peer [peer-addre...

  • Page 819

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 814 description: mesh group: static rpf: not configured information about connection status: state: up password ： up/down time: 0dt03h04m41s connection interface: vlan1(10.1.1.3) keep-alive/hold-time interval: 60/75 remote...

  • Page 820

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 815 the total times of this peer transfer into up state the total times the msdp state transitioned into the “up” state incoming filter the sa message incoming filter configured on this msdp peer. Outgoing filter the sa me...

  • Page 821

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 816 example this example shows how to display sa cache information. Switch# show ip msdp sa-cache msdp source-active cache information ： group address source address rp address learned peer up/expire time 230.1.1.0 192.168...

  • Page 822

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 817 switch# 68-25 show ip msdp mesh-group this command is used to display msdp mesh group configuration. Show ip msdp mesh-group [peer-address] parameters peer-address (optional) specifies the msdp peer ip address. Default...

  • Page 823

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 818 69. Multicast vlan commands 69-1 mvlan enable this command is used to enable multicast vlan and configure some options for the multicast vlan feature. Use the no form of this command to disable the state or return to t...

  • Page 824

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 819 forward-unmatched specifies that if the received igmp or mld control packet is untagged, does not match any profile, and the associated default vlan is a multicast vlan, or is tagged with a multicast vlan, but does not...

  • Page 825

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 820 69-3 mvlan vlan this command is used to create a multicast vlan. Use the no form of this command to remove a multicast vlan. Mvlan vlan vlan-id no mvlan vlan vlan-id parameters vlan vlan-id specifies the multicast vlan...

  • Page 826

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 821 untagged specifies that if the port is an untagged member, then the packets will be forwarded in the untagged form. Interface-id specifies an interface or an interface list. No spaces are allowed before and after the c...

  • Page 827

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 822 vlan-name specifies the vlan name, with a maximum of 32 characters. Default the default multicast vlan name is mvlanxxxx, where xxxx represents four numeric digits (including the leading zero) that are equal to the vla...

  • Page 828

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 823 example this example shows how to configure replacing the ipv4 packet priority to 4. Switch# configure terminal switch(config)# mvlan switch(config)# mvlan 100 switch(config-mvlan)# replace-priority ipv4 4 switch(confi...

  • Page 829

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 824 switch(config)# mvlan switch(config)# mvlan 100 switch(config-mvlan)# replace-source-ip ipv4 1.10.10.10 from receiver switch(config-mvlan)# replace-source-ip ipv6 fe80:3000::3 from source switch(config-mvlan)# 69-8 mvl...

  • Page 830

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 825 profile-name specifies the name of the profile. Default none. Command mode multicast vlan configuration mode. Command default level level: 12. Usage guideline a single multicast vlan can be bound with more than one pro...

  • Page 831

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 826 command default level level: 12. Usage guideline multiple ranges can be added to a multicast vlan profile. The ip address ranges, specified in a single profile, must be of the same address family. Example this example ...

  • Page 832

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 827 69-12 show mvlan access-group this command is used to display which multicast group profiles are bound to which multicast vlans. Show mvlan access-group [vlan-id] parameters vlan-id specifies the vlan id. Default none....

  • Page 833

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 828 command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display all configurations and information of the multicast vlan by not specifying the vlan id. Exam...

  • Page 834

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 829 replace source ip the source ip address that will be replaced in the igmp/mld control packets before forwarded in the multicast vlan..

  • Page 835: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 830 70. Multiple spanning tree protocol (mstp) commands 70-1 instance this command is used to map a vlan or a set of vlans to an mst instance. Use the no instance without vlans specified to remove instances. Use the no ins...

  • Page 836

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 831 this command is used to configure the name of an mst region. To return to the default name, use the no form of this command. Name name no name name parameters name specifies the name given for a specified mst region. T...

  • Page 837

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 832 mst configuration mode. Command default level level: 12. Usage guideline two ethernet switches that have the same configuration but different revision numbers are considered to be part of two different regions. Example...

  • Page 838

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 833 use this command to display the mstp configuration and operation status. If a private vlan is configured and the secondary vlan does not map to the same primary vlan, the show spanning-tree mst configuration command wi...

  • Page 839

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 834 designated root address: 00:02.17:2c.F4:00, priority: 32771, cost: 0 designated bridge address: 00.02.17.2c.F4.00 priority 32771, port id: 128.1 eth1/0/2 port state: forwarding port role: designated, port info: port id...

  • Page 840

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 835 designated root address: 00-54-85-26-05-00, priority: 4096 (4096 sysid 0) regional root address: 00-12-85-26-05-00, priority: 32768 designated bridge address: 00-12-85-26-05-00, priority: 32768 topology changes count :...

  • Page 841

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 836 switch# this example shows how to display mstp summary information for interfaces ethernet 1/0/3 to 1/0/4 of mst02. Switch# show spanning-tree mst instance 2 interface ethernet 1/0/3-4 >>>>mst02 vlans mapped: 2-3 bridg...

  • Page 842

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 837 default the cost value depends on the port speed. The faster the interface's speed is will indicate a smaller cost. Mst always uses long path costs. The default priority value is 128. Command mode interface configurati...

  • Page 843

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 838 70-7 spanning-tree mst max-hops this command is used to configure the mstp maximum hop count value. Use the no form of the command to reset to the default setting. Spanning-tree mst max-hops hop-count no spanning-tree ...

  • Page 844

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 839 interface configuration mode. Command default level level: 12. Usage guideline this mstp hello-time only takes effect in the mstp mode. Example this example shows how to configure the port hello-time to 1 for the ether...

  • Page 845

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 840

  • Page 846: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 841 71. Multiprotocol label switching (mpls) commands 71-1 backoff this command is used to configure the initial and maximum back-off delay time. Use the no form of this command to restore the default value. Backoff init-t...

  • Page 847

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 842 parameters cos-list to exp-value specifies the list of cos values to an exp value. The series of cos values can be separated by commas (,) or hyphens (-) with no spaces or hyphens before and after. Cos-list specifies t...

  • Page 848

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 843 default exp to cos map: • cos: 0 1 2 3 4 5 6 7 • exp: 2 0 1 3 4 5 6 7 command mode mpls qos configuration mode. Command default level level: 12. Usage guideline the exp to cos map is used to map an exp value in the enc...

  • Page 850

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 845 no discovery targeted-hello accept parameters none. Default by default, this option is enabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline if targeted hello message acce...

  • Page 851

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 846 level: 12. Usage guideline ldp sends the targeted hello message at the configured interval to discover the neighbor. For a discovered neighbor, ldp maintains a hold-timer. The neighbor will time out if the timer has ex...

  • Page 852

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 847 switch(config)# mpls ldp configuration switch(config-ldp)# discovery transport-address 192.168.0.1 warning: the configuring will lead to ldp sessions restart. Switch(config-ldp)# 71-9 distribution-mode this command is ...

  • Page 853

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 848 explicit-null no explicit-null parameters none. Default by default, this option is implicit null. Command mode ldp configuration mode. Command default level level: 12. Usage guideline use this command in the egress rou...

  • Page 854

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 849 usage guideline this command is used to configure the ldp session keep-alive hold-time. Ldp maintains a keep-alive hold timer for each peer session. If the keep-alive hold timer expires without receipt of an ldp pdu fr...

  • Page 855

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 850 71-13 loop-detection this command is used to enable loop detection. Use the no form of this command to disable loop detection. Loop-detection no loop-detection parameters none. Default by default, this option is disabl...

  • Page 856

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 851 by default, the lsp control mode is configured as independent. Command mode ldp configuration mode. Command default level level: 12. Usage guideline in independent lsp control, each label switching router (lsr) indepen...

  • Page 857

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 852 command default level level: 12. Usage guideline this command is used to configure lsp trigger filter rules. The lsp trigger filter rules are ip access list rules that it is used to control the ip routes that can be us...

  • Page 859

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 854 default by default, this option is disabled. Command mode ldp configuration mode. Command default level level: 12. Usage guideline use this command to enable ldp authentication. If the ldp md5 authentication is enabled...

  • Page 860

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 855 example this example shows how to enable mpls globally and enable mpls on vlan 100. Switch# configure terminal switch(config)# mpls ip switch(config)# interface vlan100 switch(config-if)# mpls ip switch(config-if)# 71-...

  • Page 861

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 856 mpls ldp configuration parameters none. Default none. Command mode global configuration mode. Command default level level: 12. Usage guideline use the command to enter the ldp configuration mode to configure ldp relate...

  • Page 862

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 857 command to set the mapping from exp to priority for incoming mpls packets. The inbound exp cos mapping takes effect only when trust exp is enabled. Use the class-map cos-exp command to set the mapping table for mapping...

  • Page 863

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 858 use this command to add a static ftn entry. At the ingress label edge router (ler), the incoming ip packets that are classified to the forwarding equivalence class (fec) will be pushed with the mpls label and forwarded...

  • Page 864

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 859 this example shows how to configure a static ilm that swaps the label from 100 to 200 for the prefix fec 172.18.10.0/24 at the transit lsr. Switch# configure terminal switch(config)# mpls static ilm in-label 100 forwar...

  • Page 865

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 860 warning: the configuring will lead to the ldp session of the peer restart. Switch(config-ldp)# 71-26 neighbor targeted this command is used to create an ldp targeted peer. Use the no form of this command to remove a co...

  • Page 866

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 861 by default, this value is 254. Command mode ldp configuration mode. Command default level level: 12. Usage guideline if loop detection is enabled, the ldr id that is in the path vector list of the label mapping message...

  • Page 867

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 862 example this example shows how to check the connectivity of the lsp for network 192.1.1.0/24. Switch# ping mpls ipv4 192.1.1.0/24 reply from 192.1.1.1, time reply from 192.1.1.1, time reply from 192.1.1.1, time reply f...

  • Page 868

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 863 usage guideline the lsr id is used to identify the lsr in the mpls network. It is recommended to set the lsr id to the ip address of a loopback interface. If the command is not configured, by default, the ldp will auto...

  • Page 869

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 864 switch# this example shows how to display the mpls’s global settings. Switch# show mpls mpls status : enabled lsp trap status : disabled switch# 71-31 show mpls forwarding-table this command is used to display the mpls...

  • Page 870

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 865 this example shows how to display all detailed mpls label forwarding path information. Switch# show mpls forwarding-table detail lsp: 1 type: transit status: up fec: 201.1.1.0/24 owner: ldp in label: 1020 out label: sw...

  • Page 871

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 866 default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline this command is used to display all ldp label binding information. Example this example shows how to displ...

  • Page 872

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 867 usage guideline this command displays the interfaces on which ldp neighbor has been discovered. Example this example shows how to display all mpls ldp neighbors. Switch# show mpls ldp discovery local ldp identifier: 10...

  • Page 873

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 868 tcp port : 646 udp port : 646 max pdu length : 1500 initial backoff : 15 seconds max backoff : 600 seconds transport address : 3.3.3.3 keep alive time : 60 seconds link hello holdtime : 15 seconds link hello interval :...

  • Page 874

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 869 oper state : disabled targeted hello accept : acceptable hello interval : 5(sec) hello hold time : 15(sec) distribution method : dod interface: if2 -------------------------------------- admin state : enabled oper stat...

  • Page 875

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 870 distribution method : du loop detect : disabled path vector limit : 0 max pdu length : 1500 peer : 192.1.1.1:0 -------------------------------------- protocol version : 1.0 transport address : 192.1.1.1 keep alive time...

  • Page 876

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 871 this example shows how to display ldp neighbors’ password configurations. Switch# show mpls ldp neighbor password neighbor password ------------ ---------- 202.11.1.1 123456 192.1.1.1 abcd total entries : 2 switch# 71-...

  • Page 878

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 873 switch# this example shows how to display ldp session statistics for peer 10.1.1.2. Switch# show mpls ldp session peer 10.1.1.2 statistic peer 10.1.1.2 ------------------------------------------- notification message :...

  • Page 879

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 874 sessionrejectedaderrors : 0 sessionrejectedmaxpduerrors : 0 sessionrejectedlrerrors : 0 badldpidentifiererrors : 0 badpdulengtherrors : 0 badmessagelengtherrors : 0 badtlvlengtherrors : 0 malformedtlvvalueerrors : 0 ke...

  • Page 881

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 876 switch# 71-43 snmp-server enable traps mpls ldp this command is used to enable the ldp trap state. Use the no form of this command to disable the ldp trap state. Snmp-server enable traps mpls ldp no snmp-server enable ...

  • Page 882

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 877 command default level level: 12. Usage guideline this command used to configure the mpls lsp trap state. Example this example shows how to enable the mpls lsp trap state. Switch# configure terminal switch(config)# snmp...

  • Page 883

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 878 reply from 192.1.1.1, time=40ms trace complete. Switch# this example shows how to trace route the lsp for network 110.1.1.0/24. Switch# traceroute mpls ipv4 110.1.1.0/24 reply from 170.1.1.1, time request timed out tra...

  • Page 884

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 879.

  • Page 885: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 880 72. Neighbor discovery (nd) inspection commands 72-1 ipv6 nd inspection policy this command is used to create an nd inspection policy. This command will enter into the nd inspection policy configuration mode. Use the n...

  • Page 886

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 881 default by default, this option is disabled. Command mode nd inspection policy configuration mode. Command default level level: 12. Usage guideline when the switch receives an nd message that contains a link-layer addr...

  • Page 887

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 882 this example shows how to create a nd policy named “policy1” and configures the device’s role to host. Switch# configure terminal switch(config)# ipv6 nd inspection policy policy1 switch(config-nd-inspection)# device-r...

  • Page 888

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 883 show ipv6 nd inspection policy [policy-name] parameters policy-name (optional) specifies the ipv6 ra guard policy name. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Us...

  • Page 889

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 884 73. Network access authentication commands 73-1 authentication guest-vlan this command is used to configure the guest vlan setting. Use the no form of the command to remove the guest vlan. Authentication guest-vlan vla...

  • Page 891

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 886 73-3 authentication periodic this command is used to enable periodic re-authentication for a port. Use the no form of this command to disable periodic re-authentication. Authentication periodic no authentication period...

  • Page 892

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 887 level: 12. Usage guideline when the inactivity timer is configured, a user session will be terminated if the session sustains no activity for the configured period of time. If the inactivity timer is configured, it sho...

  • Page 893

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 888 authentication timer restart seconds no authentication timer restart parameters seconds specifies the authentication restart timer value. The range is from 1 to 65535 default by default, this value is 60 seconds. Comma...

  • Page 894

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 889 none. Command mode global configuration mode. Command default level level: 12. Usage guideline use this command to configure the local database used for user authentication. Example this example shows how to create a l...

  • Page 895

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 890 73-9 authentication username mac-format this command is used to configure the mac address format that will be used for authenticating as the username via the radius server. Use the no form of this command to return to ...

  • Page 896

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 891 switch(config)# authentication username mac-format case uppercase delimiter hyphen number 5 switch(config)# 73-10 authentication max users this command is used to configure the maximum authenticated users for the entir...

  • Page 897

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 892 authentication mac-move deny no authentication mac-move deny parameters none. Default by default, this option is disabled. Command mode global configuration mode. Command default level level: 12. Usage guideline this c...

  • Page 898

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 893 by default, this option is enabled. Command mode global configuration mode. Command default level level: 12. Usage guideline the command is used to enable or disable the acceptance of an authorized configuration. When ...

  • Page 899

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 894 usage guideline use this command without parameters to display the sessions associated with all ports. Example this example shows how to display sessions on ethernet port 1/0/1. Switch# show authentication sessions int...

  • Page 900

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 895 authentication. Method the authentication method, such as 802.1x, mac-auth, web-auth, jwac, etc… state the method authentication state. Authenticating – host is under authentication by this method. Success – host pass ...

  • Page 901

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 896 the authenticator pae state machine and the supplicant. Fail: indicates that the authentication server has confirmed the supplicant is an illegal client. The backend state machine will notify the authenticator pae stat...

  • Page 902

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 897 74. Network load balancing (nlb) commands 74-1 nlb unicast-fdb this command is used to add a unicast mac entry to the nlb unicast address table. Use the no form of the command to remove a unicast entry from the nlb uni...

  • Page 903

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 898 learnt in the layer 2 mac address table. In this situation, the nlb has higher priority; the dynamically learnt fdb entry won't take effect. Example this example shows how to add an nlb unicast address 00-f3-22-0a-12-f...

  • Page 904

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 899 set as the nlb multicast mac address. Nlb entry 01:00:5e:xx:xx:xx (ipv4 multicast mapped mac address) has higher priority. Example this example shows how to add a multicast address 01-f3-22-0a-12-f4 received on vlan 1 ...

  • Page 905: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 900 75. Open shortest path first version 2 (ospfv2) commands 75-1 area default-cost this command is used to specify the cost associated with the type-3 default route that will be automatically injected into the stub area a...

  • Page 906

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 901 parameters area-id specifies the id of the area to be assigned as an nssa area. No-summary (optional) specifies that this function only takes effect when the router is an abr. Default no nssa area is defined. If no-sum...

  • Page 907

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 902 area-id specifies the area from which the routes will be summarized. Network-prefix specifies the network prefix of the summary route. Network-mask specifies the network mask of the summary route. Advertise (optional) ...

  • Page 908

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 903 router configuration mode. Command default level level: 12. Usage guideline the command no area area-id stub removes all stub related settings associated with the area. The area remains as a stub area. Use this command...

  • Page 909

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 904 password authentication. Message-digest-key key-id md5 key (optional) specifies an up to 16 bytes long md key for md5 message digest authentication. Default by default, no ospf virtual link is defined. Command mode rou...

  • Page 910

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 905 privileged exec mode. Command default level level: 12. Usage guideline when an ospf process is cleared, the ospf routing database will be cleared and the process is restarted. Example this example shows how to clear th...

  • Page 911

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 906 switch(config-router)# 75-8 default-metric (ospf) this command is used to configure the default metric value for the routing protocol. Use the no command to remove the default metric setting. Default-metric metric-valu...

  • Page 912

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 907 inter-area specifies the distance for ospf inter-area routes. Intra-area specifies the distance for ospf intra-area routes. External-1 specifies the distance for ospf external type-5 and type-7 routes with a type-1 met...

  • Page 913

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 908 area-id specifies the identifier of the area that contains the stub host entry. Cost specifies cost for the stub host entry. The range is from 0 to 65535. Default by default, the cost value is 1. By default, no host is...

  • Page 914

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 909 this example shows how to enable message authentication on interface vlan 1. Switch# configure terminal switch(config)# interface vlan1 switch(config-if)# ip ospf authentication message-digest switch(config-if)# 75-12 ...

  • Page 915

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 910 no ip ospf cost parameters cost cost specifies the value of the link-state metric. The range of value is from 1 to 65535. Default by default, cost is not configured. The cost is automatically calculated. Command mode i...

  • Page 916

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 911 command default level level: 12. Usage guideline the dead-interval is the amount of time that the router waits to receive an ospf hello packet from the neighbor before declaring the neighbor down. This value is adverti...

  • Page 917

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 912 75-16 ip ospf message-digest-key this command is used to configure the md5 digest key for ospf md5 authentication. Use the no command to remove an md5 key. Ip ospf message-digest-key key-id md5 key no ip ospf message-d...

  • Page 919

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 914 by default, this value is 1. Command mode interface configuration mode. Command default level level: 12. Usage guideline the ospf router will determine a designated router for the multi-access network. This command set...

  • Page 920

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 915 switch(config)# interface vlan1 switch(config-if)# ip ospf bfd switch(config-if)# 75-20 network area this command is used to enable ospf routing with the specified area id on interfaces with ip addresses that match or ...

  • Page 921

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 916 area-id specifies the area id. Default none. Command mode router configuration mode. Command default level level: 12. Usage guideline this command is used to remove the settings associated with an area. The area revert...

  • Page 922

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 917 switch# configure terminal switch(config)# router ospf switch(config-router)# passive-interface vlan1 switch(config-router)# 75-23 redistribute this command is used to redistribute routes from one routing domain into a...

  • Page 923

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 918 plus the advertised cost to reach the destination. An external metric only considers the advertised metric to reach the destination. Use the redistribute or the default-information router configuration commands only on...

  • Page 924

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 919 this command is used to specify a router id for the ospf process. Use the no command to return to the default option. Router-id router-id no router-id parameters router-id specifies the router id in the ipv4 address fo...

  • Page 925

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 920 usage guideline use this command to display general ospf protocol information. It provides system wide statistics and per-area statistics for ospf. The lsdb database overflow limit is the capacity for the lsa table siz...

  • Page 926

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 921 this command is used to display the database summary for ospf information. Show ip ospf [vrf vrf-name] database parameters vrf vrf-name (optional) specifies the ipv4 ospf vrf process. Default none. Command mode user ex...

  • Page 927

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 922 link id adv router age seq# cksum route 2.1.1.0 10.47.65.160 57 0x80000002 0xff3e 2.1.1.0/24 nssa-external link states (area 0.0.0.61 [nssa]) link id adv router age seq# cksum route tag 1.0.0.0 10.47.65.160 117 0x80000...

  • Page 928

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 923 link state id: 10.64.84.200 advertising router: 10.64.84.200 ls seq number: 800037c8 checksum: 0xd851 length: 96 number of links: 2 link connected to: stub network (link id) network/subnet number: 126.10.62.0 (link dat...

  • Page 929

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 924 example this example shows how to display information about the autonomous system boundary router (asbr) summary lsas. Switch# show ip ospf database asbr-summary asbr-summary link states (area 0.0.0.0) ls age: 893 opti...

  • Page 930

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 925 ip-address specifies the advertise router ip address. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display information about the au...

  • Page 931

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 926 vrf vrf-name (optional) specifies the ipv4 ospf vrf process. Link-state-id specifies the link state id (as an ip address). Self-originate specifies the self-originated link states. Adv-router specifies to display all t...

  • Page 933

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 928 external route tag: 0 total entries: 1 switch# 75-33 show ip ospf database self-originate this command is used to display lsas generated by the local router. Show ip ospf [vrf vrf-name] database self-originate paramete...

  • Page 934

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 929 (link data) router interface address: 172.0.14.101 number of tos metrics: 0 tos 0 metric: 1 link connected to: a transit network (link id) designated router address: 172.0.15.2 (link data) router interface address: 172...

  • Page 936

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 931 ls seq number: 80000006 checksum: 0xb55d length: 48 number of links: 2 link connected to: a virtual link (link id) neighboring router id: 10.47.65.160 (link data) router interface address: 47.65.51.2 number of tos metr...

  • Page 938

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 933 level: 1. Usage guideline use this command to display information about the lsas in the stub and nssa areas. Example this example shows how to display information about the lsas in the stub and nssa areas. Switch# show...

  • Page 939

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 934 checksum: 0xe359 length: 28 network mask: /24 tos: 0 metric: 1 total entries: 3 switch# 75-37 show ip ospf interface this command is used to display interface information for ospf. Show ip ospf interface [interface-id]...

  • Page 940

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 935 designated router (id) 222.200.23.2, interface address 2.0.0.2 backup designated router (id) 222.200.23.1, interface address 2.0.0.1 timer intervals configured, hello 10, dead 40, retransmit 5 current authentication ty...

  • Page 941

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 936 total entries: 4 switch# switch#show ip ospf neighbor detail neighbor 110.2.2.2, interface address 10.10.9.2 in the area 0.0.0.0 via interface vlan1 neighbor priority is 1, state is full, 6 state changes dr is 10.10.9....

  • Page 942

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 937 75-39 show ip ospf virtual-links this command is used to display virtual link information. Show ip ospf virtual-links [vrf vrf-name] parameters vrf vrf-name (optional) specifies the ipv4 ospf vrf process. Default none....

  • Page 943

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 938 no debug ip ospf parameters none. Default by default the ospf debug function is turned off. Command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to turn on or turn off th...

  • Page 944

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 939 switch# debug ip ospf neighbor switch# nbr 2.2.2.2 state change from loading to full tic 100 nbr 3.3.3.3 state change from full to down tic 100 75-42 debug ip ospf interface this command is used to turn on the ospf int...

  • Page 945

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 940 parameters none. Default by default the ospf interface state debug switch is turned off. Command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to turn on or turn off the o...

  • Page 946

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 941 switch# debug ip ospf lsa-flooding switch# received lsa type 1 id 2.2.2.2 from nbr 2.2.2.2 in area 0.0.0.0 seq 80000001 csum fe3a tic 15 flood lsas in area 0.0.0.0 tic 15 75-45 debug ip ospf packet-receiving this comma...

  • Page 947

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 942 none. Default by default the ospf packet transmitting debug switch is turned off. Command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to turn on or turn off the ospf pac...

  • Page 948

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 943 running spf-intra for area 0.0.0.0 tic 300 spf-intra calculation completed tic 310 75-48 debug ip ospf timer this command is used to turn on the ospf timer debug switch. Use the no form of the command to turn off the o...

  • Page 949

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 944 by default the ospf virtual link switch is turned off if the ospf debug function is turned on. Command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to turn on or turn off...

  • Page 950

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 945 75-51 debug ip ospf redistribution this command is used to turn on the ospf redistribution debug switch. Use the no form of the command to turn off the ospf redistribution debug switch. Debug ip ospf redistribution no ...

  • Page 951

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 946 command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to check statistic information about ospf packet, neighbor and spf calculations. Example this example shows how to di...

  • Page 952

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 947 packet specifies to reset the ospf packet counter. Neighbor specifies to reset the ospf neighbor counter. Spf specifies to reset the ospf spf event counter. Default none. Command mode privileged exec mode. Command defa...

  • Page 953

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 948 this command is used to view detailed information about the ospf lsdb. Example this example shows how to displays detailed information about router lsas. Switch# debug ip ospf show database rt-link ospf phase2 rt link:...

  • Page 954

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 949 none. Command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to check the information about lsas that ospf is requesting to neighbors example this example shows how to disp...

  • Page 955

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 950 this example shows how to display the external routes imported into ospf. Switch# debug ip ospf show redistribution ospf redistribution list: ip nexthop state type tag ------------------ --------------- ----- ---- ----...

  • Page 956

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 951 circuit: 2.2.2.1 circuit: 10.1.1.6 switch #.

  • Page 957: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 952 76. Open shortest path first version 3 (ospfv3) commands 76-1 area default-cost this command is used to set the summary-default cost of a stub area. To disable this function, use the no form of this command. Area area-...

  • Page 958

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 953 no area area-id range ipv6-prefix/prefix-length parameters area-id specifies the identifier of the area which routes are to be summarized. It can be specified as an ipv4 address. Ipv6-prefix specifies the ipv6 prefix. ...

  • Page 959

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 954 no-summary (optional) specifies to prevent an abr from sending summary lsas into the stub area. Default by default, this option is disabled. Command mode router configuration mode. Command default level level: 12. Usag...

  • Page 960

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 955 dead-interval seconds (optional) specifies the interval in seconds, during which no packets are received and after which a neighbor is regarded as off-line. The valid setting is 1-65535. Transmit-delay seconds (optiona...

  • Page 961

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 956 76-5 auto-cost reference-bandwidth this command is used to control the reference value ipv6 ospf uses when calculating metrics for interfaces. To return the reference value to its default, use the no form of this comma...

  • Page 962

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 957 none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline the ospf database is cleared, repopulated, and then the spf algorithm is performed. Use the process id option to c...

  • Page 963

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 958 switch(config-rtr)# redistribute rip switch(config-rtr)# 76-8 distance ospf this command is used to configure the distance for specific ospf routes. Use the no form of the command to restore to the default setting. Dis...

  • Page 964

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 959 ipv6 ospf process-id area area-id [instance instance-id] no ipv6 ospf process-id area area-id [instance instance-id] parameters area-id specifies the identifier of the area. It can be specified as an ipv4 address. Proc...

  • Page 965

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 960 metric. It can be a value in the range from 1 to 65535. Default by default the cost is not configured. Command mode interface configuration mode. Command default level level: 12. Usage guideline set the metric manually...

  • Page 966

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 961 this example shows how to set the ipv6 ospf dead interval to 60 seconds. Switch# configure terminal switch(config)# interface vlan1 switch(config-if)# ipv6 ospf dead-interval 60 switch(config-if)# 76-12 ipv6 ospf hello...

  • Page 967

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 962 parameters priority specifies the number value of the priority of the router. The range is from 0 to 255. Default by default, the router priority is 1. Command mode interface configuration mode. Command default level l...

  • Page 968

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 963 after sending an lsa to a neighbor, the router keeps the lsa until it receives an acknowledgement. In case the router does not receive an acknowledgement during the set time (the retransmit interval value), it retransm...

  • Page 969

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 964 this command is used to configure an ipv6 ospf routing process and enter the router configuration mode. To remove an ospf routing process, use the no form of this command. Ipv6 router ospf process-id no ipv6 router osp...

  • Page 970

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 965 usage guideline this command removes the specified ospf area and its configuration, such as area default-cost, area range, area stub, and area virtual-link. Example this example shows how to remove area 0.0.0.3 of ospf...

  • Page 971

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 966 this command is used to redistribute routes from other routing domain into ipv6 ospf routing domain. Use the no command to disable redistribution. Redistribute protocol [metric metric-value] [metric-type type-value] no...

  • Page 972

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 967 76-20 router-id (ipv6) this command is used to specify a router id for the ospf process. Use the no command to return to the automatic router id. Router-id router-id no router-id parameters router-id specifies the rout...

  • Page 973

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 968 command mode user exec or any configuration mode. Command default level level: 1. Usage guideline the information displayed by the show ipv6 ospf command is useful in debugging ospf routing operations. Example this exa...

  • Page 974

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 969 area 0.0.0.7 (active) number of interfaces in this area is 1 active interface number is 1 number of fully adjacent virtual neighbors through this area is 0 spf algorithm executed 3 times number of lsa 26. Checksum sum ...

  • Page 976

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 971 10.76.37.3 512 0x80000001 0xdf6f 1 10.76.37.30 400 0x80000001 0x48fa 1 link-lsa (interface vlan3) adv router age seq# cksum linkcnt 10.76.37.30 400 0x80000001 0x3210 1 router-lsa (area 0.0.0.0) (backbone) adv router ag...

  • Page 977

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 972 adv router age seq# cksum prefix 10.76.37.3 346 0x80000003 0x84a6 3ffe:1::/64 10.76.37.30 395 0x80000002 0xd345 3ffe:3::/64 intra-area-prefix-lsa (area 0.0.0.1) adv router age seq# cksum ref-lstype ref-lsid prefix 10.7...

  • Page 978

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 973 neighbor interface id: 2147483649 neighbor router id: 10.47.65.182 link connected to: a virtual link metric: 1 interface id: 2147483810 neighbor interface id: 2147483649 neighbor router id: 10.47.65.183 ls age: 1766 ls...

  • Page 979

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 974 switch# this example shows how to display information about inter-area prefix lsas. Switch# show ipv6 ospf database inter-area prefix ospfv3 router with id (10.47.65.180) (process 1) inter-area-prefix-lsa (area 0.0.0.0...

  • Page 980

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 975 total entries: 2 switch# this example shows how to display information about external lsas. Switch# show ipv6 ospf database external ospfv3 router with id (10.47.65.180) (process 1) as-external-lsa ls age: 279 ls type:...

  • Page 981

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 976 ospfv3 router with id (10.47.65.180) (process 4765) link-lsa (interface vlan49) ls age: 347 ls type: link-lsa link state id: 0.0.4.49 advertising router: 10.47.65.180 ls seq number: 0x80000003 checksum: 0x62b6 length: ...

  • Page 984

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 979 mtu 1500, instance id 0 router id 10.76.37.30, network type broadcast, cost: 1 (default) transmit delay is 1 sec, state bdr, priority 1 designated router (id) 10.76.37.3 local address fe80::219:5bff:fef5:2cc1 backup de...

  • Page 986

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 981 virtual link to router 10.90.90.90 is up transit area 0.0.0.3 via interface vlan40, instance id 0 local peer address fd80::2a10:7bff:fe7d:d963/128 remote peer address 4000::a/128 transmit delay is 1 sec, state point-to...

  • Page 987

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 982 77. Policy-based routing (pbr) commands 77-1 ip policy route-map this command is used to specify a route map as the routing policy on an interface. To disable policy routing on the interface, use the no form of this co...

  • Page 988

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 983 77-2 show ip policy this command is used to display the route map used for policy-based routing. Show ip policy parameters none. Default none. Command mode user exec or any configuration mode. Command default level lev...

  • Page 990

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 985 inteface-id specifies the id of the interface to be displayed. , (optional) specifies a series of interfaces, or separate a range of interfaces from a previous range. No space is allowed before and after the comma. - (...

  • Page 991

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 986 no snmp-server enable traps port-security [trap-rate] parameters trap-rate trap-rate (optional) specifies the number of traps to send per second. The range is from 0 to 1000. The default value of 0 indicates that an sn...

  • Page 992

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 987 shutdown specifies to shut down the port if there is a security violation and record the system log. Permanent specifies that under this mode, all learned mac addresses will not be purged out unless the user manually d...

  • Page 993

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 988 • restrict - a port security violation restricts data and causes the security violation counter to increment. • shutdown - the interface is disabled, based on errors, when a security violation occurs. Example this exam...

  • Page 994

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 989 by default, the port security aging feature is disabled. The default time is 0 minutes. The default aging type is absolute. Command mode interface configuration mode. Command default level level: 12. Usage guideline us...

  • Page 995

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 990 global configuration mode. Command default level level: 12. Usage guideline use this command to set the limit on the port security entry number which can be learned on a system or on vlans. Example this example shows h...

  • Page 996

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 991 79. Power saving commands 79-1 dim led this command is used to disable the port led function. Use the no form of the command to restore the led function. Dim led no dim led parameters none. Default by default, this opt...

  • Page 997

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 992 port-shutdown specifies that power saving will be applied by scheduled port shutdown. Hibernation specifies that power saving will be applied by scheduled system hibernation. This feature can only be used when physical...

  • Page 998

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 993 by default, this option is disabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline use this command to enable or disable the specified port’s eee power saving function. The...

  • Page 999

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 994 switch(config)# 79-5 power-saving hibernation time-range this command is used to configure the time range profile for the system hibernation schedule. Use the no form of the command to delete the specified time range p...

  • Page 1000

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 995 maximum length is 32 characters. Default none. Command mode interface configuration mode. Command default level level: 12. Usage guideline use this command to add or delete a time range profile for the port shutdown sc...

  • Page 1001

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 996 example this example shows how to display all power saving configuration information. Switch#show power-saving function version: 3.00 link detection power saving state: disabled length detection power saving state: dis...

  • Page 1002

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 997 80. Priority-based flow control (pfc) commands 80-1 clear priority-flow-control counters this command is used to clear the priority-based flow control (pfc) counters of the specified interface(s). Clear priority-flow-c...

  • Page 1003

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 998 parameters none. Default by default, this option is disabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline priority-based flow control (pfc), which is defined in ieee 802....

  • Page 1004

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 999 interface-id (optional) specifies the interface to display. , (optional) specifies a series of interfaces, or separate a range of interfaces from a previous range. No spaces before and after the comma. - (optional) spe...

  • Page 1005

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1000 eth 1/0/28 8 off 0 0 switch# display parameters pfc cap pfc capability: specifies the device’s limitation of how many traffic classes may simultaneously be supported by pfc. Oper pfc on priorities the cos list that th...

  • Page 1007

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1002 81-2 private-vlan association this command is used to associate secondary vlans with a primary vlan. Use the no form of this command to remove the association of secondary vlans with the primary vlan. Private-vlan ass...

  • Page 1008

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1003 none. Default none. Command mode mst configuration mode. Command default level level: 12. Usage guideline the secondary vlans need to be mapped to the same mst id as the primary vlan if private vlan is configured. If ...

  • Page 1009

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1004 usage guideline for isolated ports or community ports, use the switchport mode private-vlan host command to specify the port mode and use the switchport private-vlan host-association command to associate the port with...

  • Page 1010

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1005 command mode interface configuration mode. Command default level level: 12. Usage guideline the port is an isolated port if the secondary vlan specified by the command is an isolated vlan. The port is a community port...

  • Page 1011

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1006 remove secondary-vlan- id specifies to remove membership of the specified secondary vlan. , (optional) specifies a series of vlan, or separate a range of vlan from a previous range. No space is allowed before and afte...

  • Page 1012

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1007 parameters vlan-id specifies the vlan id. The valid range is from 2 to 4094. Tag specifies to enable the tagging mode of the trunk native vlan. Default by default, the native vlan is 1 and in the untagged mode. Comman...

  • Page 1013

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1008 - (optional) specifies a range of vlans. No space is allowed before and after the hyphen. Default by default, vlan 1 is allowed. Command mode interface configuration mode. Command default level level: 12. Usage guidel...

  • Page 1014

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1009 this command displays the listing of the private vlan contained in the private vlan domain, association of a secondary vlan with a primary vlan, and member port of each private vlan. Example this example shows how to ...

  • Page 1015: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1010 82. Protocol independent multicast (pim) ipv6 commands 82-1 ipv6 pim this command is used to enable ipv6 pim sparse-mode on an interface. To disable this function, use the no form of this command. Ipv6 pim sparse-mode...

  • Page 1016

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1011 command mode interface configuration mode. Command default level level: 12. Usage guideline when an interface is configured as a border, it will prevent bootstrap router (bsr) messages from being sent or received thro...

  • Page 1017

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1012 usage guideline this command only affects pim-sm operation. This command causes the router to send bootstrap messages to all its pim neighbors, with the address of the designated interface as the bsr address. A pim-sm...

  • Page 1018

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1013 this command causes the router to send a pimv2 message advertising itself as a candidate rp to the bsr. Example this example shows how to configure the router with the interface vlan 1 to be advertised as the candidat...

  • Page 1019

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1014 82-6 ipv6 pim hello-interval this command is used to configure the frequency of pim hello messages. Use the no form of this command to return to the default interval. Ipv6 pim hello-interval seconds no ipv6 pim hello-...

  • Page 1020

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1015 command mode interface configuration mode. Command default level level: 12. Usage guideline this command is only valid for the vlan interface. This command only takes effect when the interface is pim-sm enabled. When ...

  • Page 1021

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1016 this example shows how to configure vlan 100 as a pim passive interface. Switch# configure terminal switch(config)# interface vlan100 switch(config-if)# ipv6 pim passive switch(config-if)# 82-9 ipv6 pim register-check...

  • Page 1022

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1017 parameters seconds specifies the register probe time value in seconds. The range is from 1 to 127. Default by default, this value is 5 seconds. Command mode global configuration mode. Command default level level: 12. ...

  • Page 1023

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1018 suppression time to prevent a possible negative value in the setting of the register-stop timer. The minimal value for register suppression time is 3. Example this example shows how to configure the register suppressi...

  • Page 1024

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1019 ipv6 pim rp-address ipv6-address [group-access-list] [override] no ipv6 pim rp-address ipv6-address parameters ipv6-address specifies the ipv6 address of a router to be a pim rp. Group-access-list (optional) specifies...

  • Page 1026

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1021 command mode global configuration mode. Command default level level: 12. Usage guideline this command only affects pim sm operation. Pim source-specific multicast (pim-ssm) builds trees that are rooted in just one sou...

  • Page 1027

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1022 command default level level: 12. Usage guideline this command only affects ipv6 pim-sm. This command is used to configure the keep-alive timer, which is the period during which the pim router will maintain the (s, g) ...

  • Page 1029

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1024 this example shows how to display information that has been learned from various c-rps at the bsr. In this example, two candidate rps have sent advertisements for the ff00::/8 or the default ipv6 multicast range. Swit...

  • Page 1030

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1025 source, such as the bootstrap router (bsr) or static configuration. Bsr specifies to display ranges learned through the bsr. Embedded-rp specifies to display group ranges learned through the embedded rendezvous point ...

  • Page 1031

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1026 82-20 show ipv6 pim interface this command is used to display the configuration for protocol independent multicast (pim) on interface(s). Show ipv6 pim interface sparse-mode [interface-id] [detail] parameters interfac...

  • Page 1032

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1027 interface link-local address : fe80::207:e9ff:fe02:81d interface global address : 3ffe:192:168:1::53 mode : sparse designated router : fe80::20e:cff:fe01:facc designated router priority : 1 designated router priority ...

  • Page 1033

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1028 82-21 show ipv6 pim mroute this command is used to display the pim ipv6 multicast routing table. Show ipv6 pim mroute sparse-mode parameters none. Default none. Command mode user exec or any configuration mode. Comman...

  • Page 1034

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1029 assert state: no info, assert timer: off assert winner: ::, metric: 0, pref: 0 (3ffe:6000:1005::dd, ff13::10, rpt) uptime: 0dt00h00m05s, flags:s rp: 3ffe:6000:1005::36, rpf nbr: fe80::217:55ff:fec0:16, rpf interface: ...

  • Page 1035

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1030 82-22 show ipv6 pim neighbor this command is used to display pim neighbor information. Show ipv6 pim neighbor sparse-mode [detail] [interface-id] parameters detail (optional) specifies to display ipv6 pim neighbor inf...

  • Page 1036

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1031 ver indicates the pim version used by this neighbor. Dr pri/mode the priority and mode of the designated router (dr). Dr priority: uses n to indicate that the neighbor does not support the dr priority option in the he...

  • Page 1037: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1032 83. Protocol independent multicast (pim) commands 83-1 ip pim this command is used to enable pim on the interface for either sparse mode (sm) or dense mode (dm) operation. Use the no command to disable the pim functio...

  • Page 1038

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1033 switch(config-if)# ip pim sparse-mode switch(config-if)# 83-2 ip pim bsr-border this command is used to configure the avoidance of sending and receiving bsr messages through an interface. Use the no command to allow t...

  • Page 1039

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1034 range is 0 to 32. If not specified, the default length is 30. Priority specifies to configure the priority for a cbsr. The candidate with the highest priority is preferred. If the priority values are the same, the rou...

  • Page 1040

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1035 command mode interface configuration mode. Command default level level: 12. Usage guideline this command only takes effect when the interface is pim-sm enabled. In the dm mode, the dr priority option will not be carri...

  • Page 1041

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1036 this example shows how to configure the pim join/prune timer to 120 seconds. Switch# configure terminal switch(config)# interface vlan 1 switch(config-if)# ip pim jp-timer 120 switch(config-if)# 83-6 ip pim passive th...

  • Page 1042

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1037 parameters seconds specifies the interval at which the hello message is sent. Default by default, this value is 30 seconds. Command mode interface configuration mode. Command default level level: 12. Usage guideline t...

  • Page 1043

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1038 usage guideline if this setting is disabled, the checksum for the registered packets is calculated only over the header. This command can be only specified once. The later applied command will override the previous se...

  • Page 1044

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1039 this command is used to configure the register suppression time. Use the no form of the command to revert to the default setting. Ip pim register-suppression seconds no ip pim register-suppression parameters seconds s...

  • Page 1045

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1040 command mode global configuration mode. Command default level level: 12. Usage guideline this command is used to specify the static multicast groups to rp mapping. In a multicast domain, the static multicast group to ...

  • Page 1046

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1041 default the router is not an rp candidate by default. Command mode global configuration mode. Command default level level: 12. Usage guideline only one group access list can be specified for each interface. This comma...

  • Page 1047

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1042 this example shows how to configure the pim register keep-alive time to 500 seconds. Switch# configure terminal switch(config)# ip pim rp-register-kat 500 switch(config)# 83-14 ip pim spt-threshold this command is use...

  • Page 1048

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1043 parameters default specifies to use the default ssm group addresses. The default ssm group address range is 232/8. Access-list specifies the standard ip access list that defines the user-specified ssm group addresses....

  • Page 1049

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1044 usage guideline use this command to display the global information of pim. Example this example shows how to display pim global information. Switch# show ip pim pim configurations: register checksum wholepkt: (not con...

  • Page 1050

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1045 example this example shows how to display bsr information on the bsr router with the candidate rp information on the router’s interface, vlan 100. Switch# show ip pim bsr-router pimv2 bootstrap information this system...

  • Page 1051

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1046 command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display interface related information. If no interface is specified, the pim information for all ap...

  • Page 1052

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1047 address : 12.1.1.1 pim : enabled mode : sparse-dense neighbor count : 0 dr : 12.1.1.1 dr priority : 1 generation id : 9e3d65 hello interval : 30 seconds join prune timer : 60 seconds pim passive mode : disabled total ...

  • Page 1053

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1048 total entries: 4 switch# 83-20 show ip pim rp mapping this command is used to display group-to-rp (rendezvous point) mappings and the rp set. Show ip pim rp mapping parameters none. Default none. Command mode user exe...

  • Page 1054

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1049 router has known about this rp. Expires the time (in day, hours, minutes, and seconds) after which the information about this rp expires. If the router does not receive any refresh messages in this time, it will disca...

  • Page 1055: Snooping Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1050 84. Protocol independent multicast (pim) snooping commands 84-1 ip pim snooping this command is used to enable the pim snooping function. To disable this function, use the no command. Ip pim snooping no ip pim snoopin...

  • Page 1056

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1051 all specifies to clear all pim snooping related statistics for all vlans. Vlan vlan-id specifies to clear pim snooping related statistics for this specified vlan. Default none. Command mode privileged exec mode. Comma...

  • Page 1057

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1052 switch# this example shows how to display pim snooping information for a specific vlan. Switch# show ip pim snooping vlan 1 2 neighbors, 10 mroutes, dr is 36.90.90.100 learned neighbor on ports: 1/0/23, local switch# ...

  • Page 1059

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1054 total entries: 3 switch# 84-6 show ip pim snooping statistics this command is used to display pim snooping statistics information on the switch. Show ip pim snooping statistics [vlan vlan-id] parameters vlan vlan-id (...

  • Page 1061

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1056 parameters access-list-name specifies a standard ip access list to define which received route updates are to be accepted and which route updates are to be advertised. Interface-id (optional) specifies the interface t...

  • Page 1062

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1057 network-address/mask- length specifies a network address and the length of the mask bit. Ge-length (optional) specifies the minimum prefix length of the route that can be matched. Le-length (optional) specifies the ma...

  • Page 1063

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1058 vrf-name (optional) specifies the name of the routing forwarding instance. Network-prefix specifies the network address. Network-mask specifies the network mask. Ip-address specifies the ip address of the next hop tha...

  • Page 1064

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1059 parameters default (optional) specifies to add or delete a default route. Network-prefix/prefix- length (optional) specifies the network prefix and the prefix length of the static route. Next-hop-address (optional) sp...

  • Page 1065

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1060 parameters sip (optional) specifies to include the source ip address in the hash value computation. Crc32_lower (optional) specifies to include the lower 5 bits of the crc in the hash value computation. Crc32_upper (o...

  • Page 1066

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1061 by default, this value is 1. Command mode router configuration mode. Command default level level: 12. Usage guideline there are a number of sources that a route can be learned from. Each route is associated with a dis...

  • Page 1068

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1063 vlan8 1 1 2 vlan11 1 1 2 vlan1 1 1 2 vlan31 1 1 2 vlan32 1 1 2 vlan33 1 1 2 routing for networks: vlan10 (1.0.0.1/255.0.0.0) vlan20 (2.0.0.1/255.0.0.0) vlan40 (4.0.0.1/255.0.0.0) vlan70 (7.0.0.3/255.0.0.0) vlan8 (8.0....

  • Page 1069

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1064 1.0.0.2 2.0.0.2 4.0.0.2 7.255.255.254 8.0.0.2 11.0.0.2 131.0.0.2 132.0.0.2 133.0.0.2 4.0.0.2 distribute list: vlan1 filtered by abc. Vlan8 filtered by abc. Vlan11 filtered by abc. External-1 distance 110,external-2 di...

  • Page 1070

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1065 user exec or any configuration mode. Command default level level: 1. Usage guideline the routing table gathers routes learned from different protocols. If multiple routes can reach the same network, the one with the b...

  • Page 1071

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1066 p the stale route during restarting of protocols. 10.110.0.0/8 indicates the network. [160/5] the first number is the administrative distance of the protocol source; the second number is the metric for the route. Via ...

  • Page 1073

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1068 o ia 1005::/64 [110/20] via fe80::2c0:8fff:fe04:1128, vlan10 o ia 1005::1/128 [110/10] via fe80::2c0:8fff:fe04:1128, vlan10 o ia 1005::2/128 [110/20] via fe80::2c0:8fff:fe04:1128, vlan10 o ia 1006::/64 [110/20] via fe...

  • Page 1074

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1069 > the route with the best distance among routes learned from multiple protocols. 115:50:70::/64 indicates the network. [110/2] the first number is the administrative distance of the protocol source; the second number ...

  • Page 1075: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1070 86. Qos amendment data center bridge (dcb) commands 86-1 class type network-qos this command is used to specify the name of the type network quality of service (qos) class map to be associated with a traffic policy an...

  • Page 1076

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1071 this command is used to create or modify a type network qos class map that defines the criteria for packet matching. Class-map type network-qos match-any name parameters name specifies the name of the class map with a...

  • Page 1077

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1072 number of zero stands for strict priority mode. Default by default, 4, 7, 11, 14, 18, 21, 25 (in percentage) are assigned for traffic classes 0 to 6. By default, 0 is assigned for traffic class 7 which means that the ...

  • Page 1078

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1073 transmit characteristics. When the offered load in the traffic class doesn’t use its allocated bandwidth, ets will allow other traffic classes to use the available bandwidth. The bandwidth assigned to each traffic cla...

  • Page 1079

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1074 o use the pause policy map type network-qos class configuration command to enable pfc pause characteristics on a class referenced in a type network qos policy map. • use the service-policy type network-qos input inter...

  • Page 1080

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1075 use the policy-map type network-qos command to enter the policy-map configuration mode from where to configure or modify the policy for the traffic class. Use the class-map type network-qos match-any and match cos com...

  • Page 1081

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1076 use the service-policy type network-qos command to attach a single type network qos policy map to input interfaces. A policy map need not be created before specifying it in this command. A command will not take effect...

  • Page 1082

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1077 class map my_class_map_3 match cos 5 switch# 86-9 show mls qos queuing interface this command is used to display the weight configuration for different scheduler algorithms on specified interface(s). Show mls qos queu...

  • Page 1083

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1078 --- ------- 0 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 ets bandwidth weights: qid percentages --- ------------------ 0 10 1 20 2 30 3 40 4 strict priority 5 strict priority 6 strict priority 7 strict priority switch# 86-10 show ...

  • Page 1084

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1079 policy map: policy1(network-qos) : input class map my_class_map_2 pause policy map: policy2 : input class police police cir 500000 bc 10000 pir 1000000 be 10000 exceed-action set-dscp-transmit 2 violate-action drop sw...

  • Page 1085

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1080 pause switch#.

  • Page 1086

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1081 87. Quality of service (qos) commands 87-1 class this command is used to specify the name of the class map to be associated with a traffic policy and then enter into policy map class configuration mode. Use the no com...

  • Page 1089

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1084 • ip - ip (version 4). • ipv6 - ip (version 6). • netbios - netbios. • nfs - network file system. • ntp - network time protocol. • ospf - open shortest path first. • pppoe - point-to-point protocol over ethernet. • ri...

  • Page 1090

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1085 87-4 mls qos aggregate-policer this command is used to define a named aggregate policer for use in policy maps. To delete a named aggregate policer, use the no form of this command. The mls qos aggregate-policer comma...

  • Page 1091

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1086 color-aware (optional) specifies the option for the single rate three colors policer or two rates three colors policer. When color-aware is not specified, the policer works in the color blind mode. When color-aware is...

  • Page 1092

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1087 command mode interface configuration mode. Command default level level: 12. Usage guideline when the override option is not specified, the cos of the packets will be the packet’s cos if the packets are tagged, and wil...

  • Page 1093

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1088 use this command to attach an ingress dscp mutation table to an interface. The ingress dscp mutation will mutate the dscp value right after the packet is received by the interface, and qos handles the packet with this...

  • Page 1094

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1089 87-8 mls qos map dscp-color this command is used to define the dscp to color map for the mapping of a packet’s initial color. To return the color map to the default setting, use the no form of this command. Mls qos ma...

  • Page 1095

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1090 default cos value: 0 1 2 3 4 5 6 7 dscp value: 0-7 8-15 16-23 24-31 32-39 40-47 48-55 56-63 command mode interface configuration mode. Command default level level: 12. Usage guideline the dscp to cos map is used by a ...

  • Page 1096

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1091 when a packet is received by an interface, based on a dscp mutation map, the incoming dscp can be mutated to another dscp immediately before any qos operations. The dscp mutation is helpful to integrate domains with d...

  • Page 1097

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1092 subtracted from the corresponding credit counter and the service right is turned over to the next lower cos queue. When the credit counter drops below 0, the queue is no longer serviced until its credits are replenish...

  • Page 1098

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1093 when the interface is set to trust dscp, the dscp of the arriving packet will be trusted for the subsequent qos operations. First, the dscp will be mapped to an internal cos value, which will be subsequently used to d...

  • Page 1099

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1094 action specifies the action to take on packets. Use one of the following keywords: drop - drops the packet. Set-dscp-transmit value - sets the ip differentiated services code point (dscp) value and transmits the packe...

  • Page 1100

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1095 switch(config-cmap)# exit switch(config)# policy-map police-setting switch(config-pmap)# class access-match switch(config-pmap-c)# police 8 1 exceed-action drop switch(config-pmap-c)# exit switch(config-pmap)# exit sw...

  • Page 1101

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1096 switch(config-pmap-c)# exit switch(config-pmap)# class class3 switch(config-pmap-c)# police aggregate agg_policer1 switch(config-pmap-c)# 87-15 police cir this command is used to configure traffic policing for two rat...

  • Page 1102

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1097 policy-map class configuration mode. Command default level level: 12. Usage guideline as a packet arrives at a port, the packet will be initialized with a color. The receiving port either trusts dscp or cos. The initi...

  • Page 1103

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1098 32 alphanumeric characters. Default none. Command mode global configuration mode. Command default level level: 12. Usage guideline use the policy-map command to enter the policy-map configuration mode from where the u...

  • Page 1104

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1099 default the default priority (cos) to queue mapping is: 0 to 2, 1 to 0, 2 to 1, 3 to 3, 4 to 4, 5 to 5, 6 to 6, 7 to 7. Command mode global configuration mode. Command default level level: 12. Usage guideline when a p...

  • Page 1105

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1100 usage guideline use this command to configure the minimal and maximum bandwidth for a specified queue. When the minimal bandwidth is configured, the packet transmitted from the queue can be guaranteed. When the maximu...

  • Page 1106

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1101 level: 12. Usage guideline the specified limitation cannot exceed the maximum speed of the specified interface. For the ingress bandwidth limitation, the ingress will send a pause frame or a flow control frame when th...

  • Page 1107

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1102 for cust2-classes, gold is configured to use cos queue 6 and be policed by a single rate policer with a committed rate of 1600 kbps. Silver is policed by a single rate policer with a committed rate of 4000 kbps, and b...

  • Page 1109

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1104 switch(config-pmap)# 87-22 show class-map this command is used to display the class map configuration. Show class-map [name] parameters name (optional) specifies the name of the class map. The class map name can be a ...

  • Page 1110

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1105 name (optional) specifies the name of the aggregate policer. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline this command is used to display the configur...

  • Page 1111

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1106 map cos-color specifies to displays the cos to color map. Map dscp-cos specifies to displays the mapping of dscp to cos default none. Command mode user exec or any configuration mode. Command default level level: 1. U...

  • Page 1112

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1107 this example shows how to display the dscp mutation maps attached to eth 1/0/1 to 1/0/2. Switch# show mls qos interface ethernet 1/0/1-2 dscp-mutation interface dscp mutation map ---------- ------------------ eth1/0/1...

  • Page 1113

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1108 switch# show mls qos interface ethernet 1/0/1-2 map dscp-color eth1/0/1 dscp 0–7 are mapped to green dscp 8–40 are mapped to red dscp 41-43 are mapped to yellow eth1/0/2 dscp 0 – 7 are mapped to green switch# this exa...

  • Page 1114

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1109 default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline this command is used to display the qos dscp mutation map configuration. Example this example shows how t...

  • Page 1115

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1110 command mode user exec or any configuration mode. Command default level level: 1. Usage guideline when the optional keyword interface is entered, the weight configuration for different scheduler (wrr or wdrr) on the s...

  • Page 1117

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1112 this example shows how to the display of the policy map called policy1, created above. Switch# show policy-map policy1 policy map policy1 class police police cir 500 bc 10 pir 1000 be 10 conform-action transmit exceed...

  • Page 1118

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1113 this example shows how to configure the queue quantum of the wdrr scheduling mode, queue quantum of queue 0, queue 1, queue 2, queue 3, queue 4, queue 5, queue 6, queue 7 are 1, 2, 3, 4, 5, 6, 7, 8 respectively on int...

  • Page 1120

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1115 default by default, this option is disabled. Command mode global configuration mode. Command default level level: 12. Usage guideline qcn is a form of end-to-end congestion management defined in ieee 802.1.Qau. The pu...

  • Page 1121

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1116 switch(config)# 88-4 qcn cnpv (global) this command is used to globally assign ieee 802.1p priority as congestion notification priority value (cnpv) and generate per-interface cnpv entries with default settings for al...

  • Page 1122

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1117 defense-mode-choice (optional) specifies how to choose cnd defense mode and alternate priority for this cnpv on all ports. This setting can be overridden by defense-mode-choice option of the per-interface command. Adm...

  • Page 1123

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1118 cnpv-priority-value specifies the ieee 802.1p priority value to be the congestion notification priority value (cnpv). The valid priority range of cnpv is from 0 to 7. Admin-defense-mode specifies the cnd defense mode ...

  • Page 1124

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1119 congestion notification tlv. Comp admin admin-defense-mode (global) alternate-priority (global) comp auto controlled by the lldp congestion notification tlv. Controlled automatically (*). (*) the rule to automatically...

  • Page 1125

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1120 total number of octets stored in the queue at this set point. The valid set point range is from 100 to 4294967295. Weight cpweight-value specifies the weight change in the queue length in the calculation of the cpfb w...

  • Page 1126

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1121 switch(config)# interface ethernet 1/0/1 switch(config-if)# qcn cp 1 set-point 30000 switch(config-if)# qcn cp 1 weight 1 switch(config-if)# qcn cp 1 sample-base 160000 switch(config-if)# qcn cp 1 min-header-octets 10...

  • Page 1127

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1122 ------------------------------ auto alternate priority : 0 errored portlist : --- cnpv: 2 ------------------------------ auto alternate priority : 0 errored portlist : --- !---output suppressed. Switch# 88-8 show qcn ...

  • Page 1128

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1123 id mode choice defense mode defense mode pri. (active) (active) -------- ----------- -------------- -------------- ---- -------------- --------- eeth1/0/1 comp interior-ready n/a 0 interior-ready 0 eeth1/0/2 comp edge...

  • Page 1130

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1125 88-10 show qcn cpid this command is used to display the relationship between the cp identifier, interface, and cp index. Show qcn cpid cp-identifier parameters cp-identifier specifies the 16 hexadecimal digits for the...

  • Page 1131: 89.  Reboot Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1126 89. Reboot commands 89-1 reboot this command is used to reboot the switch. Reboot {force_agree} parameters force_agree specifies to restart the switch without confirmation. Default none. Command mode privileged exec m...

  • Page 1132

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1127 date (optional) enter the date at which the switch should initiate the reboot. The following format should be used, ddmthyy. For example, “21mar2015”. If the date is not specified, then the switch will initiate the re...

  • Page 1133

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1128 command default level level: 1. Usage guideline this command is used to display the reboot schedule configuration. Example this example shows how to display the reboot schedule configuration. Switch# show reboot sched...

  • Page 1134: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1129 90. Remote network monitoring (rmon) commands 90-1 rmon collection stats this command is used to enable rmon statistics on the configured interface. Use the no form of this command to disable the rmon statistics. Rmon...

  • Page 1135

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1130 index specifies the history group table index. The range is from 1 to 65535. Owner name specifies the owner string. The maximum length is 127. Buckets num specifies the number of buckets specified for the rmon collect...

  • Page 1136

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1131 rising-threshold value specifies the rising threshold. The valid range is from 0 to 2147483647. Rising-event-number (optional) specifies the index of the event entry that is used to notify the ringing threshold crossi...

  • Page 1137

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1132 description string specifies a description for the rmon event entry. Enter a text string with a maximum length of 127 characters. Default none. Command mode global configuration mode. Command default level level: 12. ...

  • Page 1138

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1133 alarm index 23, owned by it monitors oid: 1.3.6.1.2.1.2.2.1.10.1 every 120 second(s) taking delta samples, last value was 2500 rising threshold is 2000, assigned to event 12 falling threshold is 1100, assigned to even...

  • Page 1139

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1134 90-7 show rmon history this command is used to display rmon history statistics information. Show rmon history parameters none. Default none. Command mode user exec or any configuration mode. Command default level leve...

  • Page 1140

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1135 show rmon statistics parameters none. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline statistics for all of the configured entries are displayed. Example...

  • Page 1141

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1136 global configuration mode. Command default level level: 12. Usage guideline this command enables rmon trap state. Example this example shows how to enable the sending of rmon traps for both the falling alarm and risin...

  • Page 1142: 91.  Route Map Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1137 91. Route map commands 91-1 match interface this command is used to define a clause to match the route’s outgoing interface. Use the no command to remove the clause. Match interface interface-id no match interface par...

  • Page 1143

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1138 none. Command mode route-map configuration mode. Command default level level: 12. Usage guideline use this command in the route map configure mode to define a rule for matching routes against an ip access list. Exampl...

  • Page 1144

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1139 this example shows how to create an ip access list “myacl” first and create a route map entry to match against the next hop based on ip access list. Switch# configure terminal switch(config)# ip access-list myacl swit...

  • Page 1145

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1140 this command is used to define a clause to match the route’s metric. Use the no command to remove the clause. Match metric value no match metric parameters value specifies the metric of route. The range is from 0 to 4...

  • Page 1146

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1141 none. Command mode route-map configuration mode. Command default level level: 12. Usage guideline use this command in the route map configure mode to define a rule for matching type of ospf routes. Example this exampl...

  • Page 1147

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1142 matched, all the set statements in the rule will be performed if the entry is a permit entry. The route will be denied if the matched rule is a deny entry. Example this example shows how to create a rule entry with th...

  • Page 1148

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1143 this command is used to configure the next-hop of routers to route the packets that passes the match clauses of the configured route-map sequences. Use the no command to remove specific default next- hops. Set ip defa...

  • Page 1150

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1145 number specifies the number of the precedence value to use in the ip header. The following numbers represent the following names: • 0 - routine. • 1 - priority. • 2 - immediate. • 3 - flash. • 4 - flash-override. • 5 ...

  • Page 1151

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1146 command mode route-map configuration mode. Command default level level: 12. Usage guideline use this command to modify the metric of routes. Example this example shows how to configure the metric of routes that pass t...

  • Page 1152

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1147.

  • Page 1153

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1148 92. Router advertisement (ra) guard commands 92-1 ipv6 nd raguard policy this command is used to create an ra guard policy. The command will enter into the ra guard policy configuration mode. Use the no command to rem...

  • Page 1154

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1149 command mode ra guard policy configuration mode. Command default level level: 12. Usage guideline this command is used to set the role of the attached device. By default, the device role is host, and therefore all the...

  • Page 1155

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1150 switch(config-ra-guard)# 92-4 ipv6 nd raguard attach-policy this command is used to apply an ra guard policy on a specified interface. Use the no command to remove the binding. Ipv6 nd raguard attach-policy [policy-na...

  • Page 1156

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1151 default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline if the policy name is specified, only the specified policy information is displayed. If the policy name i...

  • Page 1157: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1152 93. Routing information protocol (rip) commands 93-1 distance (rip) this command is used to define an administrative distance of routes learned by ipv4 routing protocols. Use the no command to restore the default sett...

  • Page 1158

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1153 parameters vrf vrf-name specifies the name of the vrf instance to enter vrf address family configuration mode. Default none. Command mode router configuration mode. Command default level level: 12. Usage guideline use...

  • Page 1159

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1154 usage guideline the default metric is used in redistributing routes from other routing protocols. The routes being redistributed are learned by other protocols and have incompatible metric as rip. The specifying of th...

  • Page 1160

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1155 this command is used to specify the type of authentication used in rip version 2 packets. Use the no command to revert to the default setting. Ip rip authentication mode text no ip rip authentication mode parameters n...

  • Page 1161

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1156 usage guideline use this command to specify the version of the receive rip version for an interface. If not specified, the global setting is followed. Example this example shows how to configure the interface (vlan 1)...

  • Page 1162

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1157 ip rip v2-broadcast no ip rip v2-broadcast parameters none. Default by default, this option is disabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline rip version 2 improv...

  • Page 1163

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1158 command default level level: 12. Usage guideline use this command to specify networks in which routing updates will be sent and received. The interface that has a subnet defined belonging to a network specified by thi...

  • Page 1164

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1159 switch(config-router)# passive-interface vlan1 switch(config-router)# 93-11 redistribute (rip) this command is used to redistribute routes from other routing domains into rip. Use the no command to disable route redis...

  • Page 1165

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1160 switch(config)# router rip switch(config-router)# redistribute ospf metric 10 switch(config-router)# 93-12 router rip this command is used to configure the rip routing process. To disable the rip routing process, use ...

  • Page 1166

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1161 vrf vrf-name (optional) specifies to display the routing information in the vrf instance. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline summary address...

  • Page 1167

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1162 usage guideline this command is used to display interface specific information for rip. Example this example shows how to display interface specific information for rip. Switch# show ip rip interface vlan1 is up, line...

  • Page 1168

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1163 the default update time: 30 seconds. The default invalid time: 180 seconds. The default flush time: 120 seconds. Command mode router configuration mode. Router address family configuration (rip) mode. Command default ...

  • Page 1169

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1164 this example shows how to configure the rip version to version 2. Switch# configure terminal switch(config)# router rip switch(config-router)# version 2 switch(config-router)#.

  • Page 1170: Generation (Ripng) Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1165 94. Routing information protocol next generation (ripng) commands 94-1 clear ipv6 rip this command is used to clear the ripng process. Clear ipv6 rip parameters none. Default none. Command mode privileged exec mode. C...

  • Page 1171

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1166 command mode router configuration mode. Command default level level: 12. Usage guideline use this command to specify the default metric for routes redistributed from other routing protocols. If the routes being redist...

  • Page 1172

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1167 switch(config-rtr)# 94-4 ipv6 rip enable this command is used to enable an ipv6 rip routing process on an interface. To disable an ipv6 rip routing process on an interface, use the no form of this command. Ipv6 rip en...

  • Page 1173

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1168 command mode interface configuration mode. Command default level level: 12. Usage guideline the metric refers to the hop count. By default, when receiving an ipv6 rip route, a metric value of 1 is added to the route b...

  • Page 1174

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1169 94-7 poison-reverse this command is used to enable the poison reverse processing for an ipv6 rip process. Use the no form of the command to disable the poison-reverse processing. Poison-reverse no poison-reverse param...

  • Page 1175

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1170 by default, this option is disabled. Command mode router configuration mode. Command default level level: 12. Usage guideline if the metric option is not specified or specified as 0, the following rules are applied: •...

  • Page 1176

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1171 this example shows how to display the rip configuration information. Switch# show ipv6 rip ipv6 rip process , port 521, multicast-group ff02::9 administrative distance is 25. Maximum paths is 4 updates every 60 second...

  • Page 1177

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1172 94-11 timers this command is used to configure the ipv6 rip network timers. To restore the default timers use the no form of this command. Timers update invalid flush no timers parameters update specifies the update i...

  • Page 1178

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1173 default by default, this option is disabled. Command mode privileged exec mode. Command default level level: 15. Usage guideline use this command to turn on or turn off the ipv6 rip debug function while the global deb...

  • Page 1179

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1174 94-14 debug ipv6 rip packet-receiving this command is used to turn on the ipv6 rip packet receiving debug switch. To turn off the ipv6 rip packet receiving debug switch, use the no form of this command. Debug ipv6 rip...

  • Page 1180

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1175 level: 15. Usage guideline use this command to turn on or turn off the ipv6 rip packet transmitting debug switch. When one ipv6 rip protocol packet is sent out, the debug information will be print if the ipv6 rip debu...

  • Page 1182

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1177 rising-threshold specifies to set a percentage value of the rising cpu utilization which will trigger the safeguard engine function. Once the cpu utilization rises over the specified percentage, the safeguard engine m...

  • Page 1183

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1178 command mode global configuration mode. Command default level level: 12. Usage guideline the reasons of packets that are destined to the cpu can be classified into three groups: manage, protocol and route. The sub-int...

  • Page 1184

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1179 the following lists the reference for the supported protocols for the cpu protect type command. According to the purpose of packets destined to cpu, the router creates three virtual sub-interfaces to process the packe...

  • Page 1185

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1180 95-5 show cpu-protect safeguard this command is used to display the settings and status of the safeguard engine. Show cpu-protect safeguard parameters none. Default none. Command mode user exec or any configuration mo...

  • Page 1187

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1182 none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display the rate limit and statistics of the safeguard engine. Example this example shows how...

  • Page 1188

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1183 switch(config)# snmp-server enable traps safeguard-engine switch(config)#.

  • Page 1189: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1184 96. Secure file transfer protocol (sftp) server commands 96-1 ip sftp server this command is used to enable the sftp server function. Use the no form of this command to disable the sftp server function. Ip sftp server...

  • Page 1190

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1185 parameters seconds specifies the idle timer for the sftp server. If the sftp server detects no operation after the duration of idle timer for a specific sftp session, the switch will close this sftp session. The range...

  • Page 1191

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1186 ip sftp server : enabled protocol version : 3 idle time out : 120 secs switch#.

  • Page 1193

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1188 parameters rsa specifies to delete the rsa key pair. Dsa specifies to delete the dsa key pair. Default none. Command mode privileged exec mode. Command default level level: 12. Usage guideline this command deletes the...

  • Page 1194

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1189 level: 12. Usage guideline use this command to configure the ssh server parameters on the switch. The authentication retry number specifies the maximum number of retry attempts before the session is closed. Example th...

  • Page 1195

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1190 this command is used to specify the service port for ssh. Use the no command to return the service port to 23. Ip ssh service-port tcp-port no ip ssh service-port parameters tcp-port specifies the tcp port number. Tcp...

  • Page 1196

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1191 this command displays the rsa or dsa public key pairs. Example this example shows how to information regarding the rsa public key. Switch# show crypto key mypubkey rsa % key pair was generated at: 09:48:40, 2013-11-29...

  • Page 1197

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1192 this command is used to display the status of ssh server connections. Show ssh parameters none. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this ...

  • Page 1198

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1193 no ssh user name authentication-method parameters user name specifies the username to configure the authentication type. The user must be an existing local account. The length of the username is limited to a maximum o...

  • Page 1199

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1194 switch(config)#.

  • Page 1200

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1195 98. Secure sockets layer (ssl) commands 98-1 no certificate this command is used to delete the imported certificate. No certificate name parameters name specifies the name of the certificate to be deleted. Default non...

  • Page 1202

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1197 % importing ca certificate... Destination filename [name/msca.Ca]? Reading file from tftp://10.1.1.2/name/msca.Ca loading name/msca.Ca from 10.1.1.2 (via ethernet0):! [ok - 1082 bytes] % importing private key pem file...

  • Page 1203

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1198 98-4 crypto pki certificate chain this command is used to enter into the certificate chain configuration mode. Crypto pki certificate chain name parameters name specifies the name for the trust-point. Default none. Co...

  • Page 1204

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1199 usage guideline use the primary command to specify a given trust-point as primary. This trust-point can be used as default trust-point when the application doesn’t explicitly specify which certificate authority (ca) t...

  • Page 1205

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1200 switch# 98-7 show ssl-service-policy this command is used to display the ssl service policy. Show ssl-service-policy [policy-name] parameters policy-name (optional) specifies the name of the ssl service policy. Defaul...

  • Page 1207

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1202 example this example shows how to configure the ssl service policy “ssl-server” which associates the “tp1” trust-point. Switch# configure terminal switch(config)# ssl-service-policy ssl-server secure-trustpoint tp1 sw...

  • Page 1208: 99.  Sflow Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1203 99. Sflow commands 99-1 sflow receiver this command is used to configure a receiver for the sflow agent. Receivers cannot be added to or removed from the sflow agent. Use the no form of this command to reset one recei...

  • Page 1209

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1204 use the no sflow receiver command to reset the receiver. When a receiver expired, the receiver is disabled and the receiver entry will be reset to the default settings. The expiration timer starts to count down when i...

  • Page 1210

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1205 the user can only specify a receiver that has its owner name setup. If the receiver associated with the sampler has its owner name reset, the sampler will be reset to the default setting. The receiver id of a default ...

  • Page 1211

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1206 the user can only specify a receiver that has its owner name setup. If the receiver associated with the poller has its owner name is reset, the poller will be reset to the default setting. Setting the polling interval...

  • Page 1212

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1207 expire time : 86500 current countdown time : 86122 max datagram size : 1400 address : 10.1.1.2 vrf name : vrf1 port : 6343 datagram version : 5 index : 2 owner : collector2 expire time : 86500 current countdown time :...

  • Page 1213

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1208 display parameters sflow agent version indicates the mib version, organization and software revision. Sflow agent address the ipv4 address of the sflow agent. Sflow agent ipv6 address the ipv6 address of the sflow age...

  • Page 1214: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1209 100. Simple mail transfer protocol (smtp) commands 100-1 smtp server this command is used to configure the smtp server and port setting. Smtp server ip-address [vrf vrf-name] [port port] no smtp server [port] paramete...

  • Page 1215

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1210 self email-address specifies the email address that which represents the switch. Default none. Command mode global configuration mode. Command default level level: 12. Usage guideline use this command to configure the...

  • Page 1216

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1211 switch(config)# smtp recipient receiver@domain.Com switch(config)# 100-4 smtp interval this command is used to configure the smtp interval time. Use the no form of the command to recover to the default value. Smtp int...

  • Page 1217

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1212 command default level level: 1. Usage guideline this command is used to display information of smtp. Example this example shows how to display smtp information. Switch# show smtp smtp server address : 172.18.208.9 smt...

  • Page 1218

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1213 switch# configure terminal switch(config)# smtp send_testmsg subject: this is the test message subject! Content: this is the test message content! Sending mail, please wait! Switch(config)#.

  • Page 1220

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1215 this example shows how to display the snmp server host setting. Switch# show snmp host host ip address : 10.20.30.40 snmp version : v1 community name : public udp port : 50001 host ip address : 10.10.10.1 snmp version...

  • Page 1221

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1216 ip access control list: groupname: initial securitymodel: v3/noauth readview : restricted writeview : notifyview : restricted ip access control list: groupname: private securitymodel: v1 readview : communityview write...

  • Page 1222

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1217 when the username argument is not specified, all configured users will be displayed. The community string created will not displayed by this command. Example this example shows how snmp users are displayed. Switch# sh...

  • Page 1223

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1218 community view name access right private communityview read/write public communityview read only command mode global configuration mode. Command default level level: 12. Usage guideline this command provides an easy w...

  • Page 1224

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1219 this example shows how to configure the snmp engine id to 332200000000000000000000. Switch# configure terminal switch(config)# snmp-server engineid local 3322 switch(config)# 101-5 snmp-server group this command is us...

  • Page 1225

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1220 command default level level: 12. Usage guideline an snmp group defines a user group by specifying the allowed security model, the read-view, the write- view, and the notification view. The security model defines that ...

  • Page 1226

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1221 auth specifies to authenticate the packet but not to encrypt it. Noauth specifies not to authenticate and to encrypt the packet. Priv specifies to both authenticate and to encrypt the packet. Community-string specifie...

  • Page 1227

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1222 this example shows how to configure the trap recipient 163.10.50.126 with version 1 with the community string “comaccess”. The udp port number is configured to 50001. Switch# configure terminal switch(config)# snmp-se...

  • Page 1228

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1223 parameters user-name specifies a username of a maximum of 32 characters. The syntax is general string that does not allow spaces. Group-name specifies the name of the group to which the user belongs. The syntax is gen...

  • Page 1230

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1225 switch(config)# snmp-server view interfacesmibview 1.3.6.1.2.1.2 included switch(config)# snmp-server group guestgroup v3 auth read interfacesmibview switch(config)# 101-10 show snmp trap link-status this command is u...

  • Page 1231

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1226 show snmp-server [traps] parameters traps (optional) specifies to display trap related settings. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use the ...

  • Page 1232

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1227 parameters interface-id (optional) specifies the interface id. If no interface is specified, then all ports will be displayed. Default none. Command mode user exec or any configuration mode. Command default level leve...

  • Page 1233

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1228 global configuration mode. Command default level level: 12. Usage guideline the snmp manager manages a snmp agent by sending snmp requests to agents and receiving snmp responses and notifications from agents. The snmp...

  • Page 1234

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1229 this command is used to enable the sending of trap packets globally. Use the no command to disable the sending of trap packets. Snmp-server enable traps no snmp-server enable traps parameters none. Default none. Comma...

  • Page 1235

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1230 linkdown (optional) specifies to control the sending of snmp linkdown notifications. A linkdown (2) trap is generated when the device recognizes a failure in one of the communication links. Coldstart (optional) specif...

  • Page 1236

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1231 none. Command mode global configuration mode. Command default level level: 12. Usage guideline use this command to configure the system’s location information on the switch. Example this example shows how to configure...

  • Page 1237

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1232 101-19 snmp-server trap-sending disable this command is used to disable the port’s trap sending state. Use the no command to disable the port’s trap sending state. Snmp-server trap-sending disable no snmp-server trap-...

  • Page 1238

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1233 global configuration mode. Command default level level: 12. Usage guideline use this command to configure the snnp udp port number on the switch. The agent will listen to the snmp request packets on the configured ser...

  • Page 1239

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1234 snmp trap link-status no snmp trap link-status parameters none. Default by default, this option is enabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline this command is u...

  • Page 1240

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1235 global configuration mode. Command default level level: 12. Usage guideline this command is used to configure the snmp context mapping table information on the switch. Example this example shows how to configure the s...

  • Page 1241

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1236 102. Single ip management (sim) commands 102-1 sim this command is used to enable single ip management. The no form of this command disables single ip management. Sim no sim parameters none. Default by default, this o...

  • Page 1242

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1237 by default, the switch role is candidate. Command mode global configuration mode. Command default level level: 12. Usage guideline there are 3 roles in the single ip management system: candidate, commander and member....

  • Page 1243

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1238 this example shows how to add one candidate switch to the single ip management group. Switch# configure terminal switch(config)# sim group-member 1 secret switch(config)# 102-4 sim holdtime this command is used to con...

  • Page 1244

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1239 parameters seconds specifies the interval value in seconds. The range is from 30 to 90. Default by default, this value is 30 seconds. Command mode global configuration mode. Command default level level: 12. Usage guid...

  • Page 1245

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1240 switch(config)# sim management vlan 100 switch(config)# 102-7 sim remote-config this command is used to remotely login and configure the single ip management group member or exit from the remote configuration. Sim rem...

  • Page 1246

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1241 is specified as the destination url, the purpose is to download the running configuration from the tftp server to member switches. When the firmware is specified as the destination url, the purpose is to download the ...

  • Page 1248

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1243 platform : dxs-3600 sim state : enabled role state : member discovery interval : 30 sec hold time : 100 sec ----------------cs info---------------- cs group name : my-group cs mac address : 00-02-01-03-01-03 cs hold t...

  • Page 1249

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1244 this example shows how to display one of the sim candidate’s information in detail. Switch# show sim candidates 1 sim candidate information ： candidate id : 1 firmware version : 2.40.041 device name : mac address : ee...

  • Page 1250

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1245 [*** member info (1/2)***] mac address : 00-07-15-34-00-50 [*** member info (2/2)***] mac address : 00-01-02-03-00-10 switch# this example shows how to display sim neighbors’ summary. Switch# show sim neighbor port ma...

  • Page 1252

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1247 comma. - (optional) specifies a range of interfaces. No space before and after the hyphen. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this comma...

  • Page 1253

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1248 interface interface-id specifies the interface id to display. , (optional) specifies a series of interfaces, or separate a range of interfaces from a previous range. No space before and after the comma. - (optional) s...

  • Page 1254

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1249 default by default this option is disabled. Command mode global configuration mode. Command default level level: 12. Usage guideline use this command to enable the sending of notification traps. When using this comman...

  • Page 1255

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1250 switch(config)# spanning-tree global state enable switch(config)# 103-6 spanning-tree (timers) this command is used to configure the spanning tree timer value. Use the no form of the command to restore the default set...

  • Page 1257

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1252 level: 12. Usage guideline in the rstp or stp-compatible mode, the administrative path cost is used by the single spanning-tree to accumulate the path cost to reach the root. In the mstp mode, the administrative path ...

  • Page 1259

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1254 mstp specifies the multiple spanning tree protocol (mstp). Rstp specifies the rapid spanning tree protocol (rstp). Stp specifies the spanning tree protocol (ieee 802.1d compatible) default by default, this mode is rst...

  • Page 1260

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1255 a port can be in one of the following three port fast modes: • edge mode - the port will directly change to the spanning-tree forwarding state when a link-up occurs without waiting for the forward-time delay. If the i...

  • Page 1261

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1256 103-14 spanning-tree priority this command is used to configure the bridge priority. It is only used for rstp and stp versions. Use the no form of this command to restore to the default setting. Spanning-tree priority...

  • Page 1262

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1257 default by default, this option is disabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline enabling tc filtering on a port is useful for an isp to prevent the external bri...

  • Page 1263

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1258 this example shows how to configure the transmit hold count value to 5. Switch# configure terminal switch(config)# spanning-tree tx-hold-count 5 switch(config)# 103-17 spanning-tree forward-bpdu this command is used t...

  • Page 1264

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1259 00-00) as the destination address of the stp bpdu. Dot1ad specifies to use provider bridge group address (01-80-c2-00-00-08) as the destination address of the stp bpdu. Default by default, the customer bridge group ad...

  • Page 1265: 104.  Stacking Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1260 104. Stacking commands 104-1 stack this command is used to enable the daisy-chain stacking function and use the no stack command to disable the daisy-chain stacking function. Stack no stack parameters none. Default by...

  • Page 1266

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1261 default the unit id is assigned automatically. Command mode privileged exec mode. Command default level level: 12. Usage guideline initially, a switch unit has no unit id assigned. When this switch unit is initialized...

  • Page 1267

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1262 command default level level: 12. Usage guideline use this command to configure the priority for the specified switch unit. When switch units are daisy- chained together as a stack, the unit with the best priority will...

  • Page 1268

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1263 show stack parameters none. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline this command is used to display the stacking information. Example this exampl...

  • Page 1269

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1264 105. Storm control commands 105-1 storm-control this command is used to configure the device to protect the device from broadcast, multicast, and da unknown packet storm attacks. Use the no form of this command to res...

  • Page 1270

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1265 use the storm control function to protect the network from a storm of broadcast packets, multicast packets, or unknown da flooding packets. Enter the storm-control command to enable storm control for a specific traffi...

  • Page 1271

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1266 this example shows how to specify the polling interval as 15 seconds. Switch# configure terminal switch(config)# storm-control polling interval 15 switch(config)# 105-3 show storm-control this command is used to displ...

  • Page 1272

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1267 total entries: 6 switch# this example shows how to display all interface settings for the range from port 3/0/1 to port 3/0/2. Switch# show storm-control interface eth1/0/1-2 polling interval : 15 sec shutdown retries...

  • Page 1273

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1268 snmp-server enable traps storm-control [storm-occur] [storm-clear] no snmp-server enable traps storm-control [storm-occur] [storm-clear] parameters storm-occur (optional) specifies to send a notification when a storm ...

  • Page 1274

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1269 106. Super vlan commands 106-1 supervlan this command is used to configure the vlan as a super vlan. Use no command to remove the super vlan assignment. Supervlan no supervlan parameters none. Default none. Command mo...

  • Page 1275

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1270 parameters vlan-id specifies the id of the vlan as a sub-vlan. The valid vlan id range is from 1 to 4094. , (optional) specifies a series of vlans, or separate a range of vlans from a previous range. No space is requi...

  • Page 1276

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1271 vlan configuration mode. Command default level level: 12. Usage guideline this command is only applicable on a sub-vlan and is used to configure the ip address range of a sub- vlan. Configuring ip address range(s) of ...

  • Page 1277

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1272 supervlan id subvlan id subvlan status subvlan ip address range ------------ --------- -------------- -------------------------------- 10 5 active 192.168.10.1 – 192.168.10.50 6 inactive 192.168.10.51 – 192.168.10.60 ...

  • Page 1278

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1273 107. Switch controller commands 107-1 packet-forwarding asf this command is used to enable the alternative store and forward (asf) feature. It allows packets to be sent in a cut-through manner. Use the no command to d...

  • Page 1281

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1276 parameters auto specifies to set the port interface’s mdix state to the auto-mdix mode. Normal specifies to force the port interface’s mdix state to the normal mode. Cross specifies to force the port interface’s mdix ...

  • Page 1283

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1278 109. System file management commands 109-1 boot config this command is used to specify the file that will be used as the configuration file for the next boot. Boot config url parameters url specifies the url of the fi...

  • Page 1284

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1279 url specifies the url of the file to be used as the boot image file. Default none. Command mode global configuration mode. Command default level level: 15. Usage guideline when using the boot image command, the associ...

  • Page 1285

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1280 109-3 clear running-config this command is used to clear the system’s running configuration. Clear running-config parameters none. Default none. Command mode privilege exec mode. Command default level level: 15. Usage...

  • Page 1286

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1281 none. Command mode privilege exec mode. Command default level level: 15. Usage guideline use this command to clear the system’s configuration, including stacking information. The configuration data will revert to the ...

  • Page 1287

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1282 none. Command mode privilege exec mode. Command default level level: 15. Usage guideline this command is used to execute the indicated configuration file to replace the current running configuration. The current runni...

  • Page 1288

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1283 this example shows how to download the “config.Cfg” from the ftp server and replace the current running configuration with it. Execute the command immediately without confirmation. Switch# configure replace ftp: //use...

  • Page 1289

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1284 is to upload one unit’s attack log. Destination-url specifies the destination url for the copied file. One special form of the url is represented by the following keywords. If running-config is specified as the destin...

  • Page 1290

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1285 this example shows how to configure the switch’s running configuration by using the increment method using the configuration called “switch-config.Cfg” that is download from the tftp server 10.1.1.254. Switch# copy tf...

  • Page 1291

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1286 switch# copy tftp: //10.1.1.254/image.Had flash: image.Had address of remote host [10.1.1.254]? Source filename [image.Had]? Destination filename [image.Had]? Accessing tftp://10.1.1.254/image.Had... Transmission star...

  • Page 1292

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1287 109-8 ip ftp source-interface this command is used to specify the interface whose ip address will be used as the source address for initiating ftp packets. To revert to the default setting, use the no form of this com...

  • Page 1293

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1288 global configuration mode. Command default level level: 12. Usage guideline use this command to specify the interface whose ip address will be used as the source address for initiating rcp packets. To do software load...

  • Page 1295

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1290 # device configure terminal end # aaa configure terminal # aaa start no aaa new-model # aaa end end # privmgmt configure terminal # command level start # command level end # level start # level end # account start # a...

  • Page 1296

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1291 #------------------------------------------------------------------------------- # dxs-3600-28sc gigabit ethernet switch # configuration # # firmware: build 2.40.041 # copyright(c) 2015 d-link corporation. All rights ...

  • Page 1297: 110.  System Log Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1292 110. System log commands 110-1 clear logging this command is used to delete log messages in the system logging buffer. Clear logging parameters none. Default none. Command mode privilege exec mode. Command default lev...

  • Page 1298

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1293 command default level level: 12. Usage guideline to enable the logging of system messages, use the logging on command in the global configuration mode. This command sends debug or error messages to a logging process, ...

  • Page 1299

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1294 default by default, the severity level is warning (4). Command mode global configuration mode. Command default level level: 12. Usage guideline the system messages can be logged to the local message buffer or to other...

  • Page 1300

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1295 discriminator (optional) specifies to filter the message to be sent to the local console based on the discriminator. Default by default, this option is disabled. Command mode global configuration mode. Command default...

  • Page 1301

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1296 severity-list specifies a list of severity levels to be filtered or to be included. Default none. Command mode global configuration mode. Command default level level: 12. Usage guideline an existing discriminator can ...

  • Page 1302

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1297 facility. If not specified, the default facility is local7 (23). See the usage guideline for more information. Facility-name (optional) specifies a facility name to represent the facility. If not specified, the defaul...

  • Page 1303

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1298 19 local3 local use 3 (local3). 20 local4 local use 4 (local4). 21 local5 local use 5 (local5). 22 local6 local use 6 (local6). 23 local7 local use 7 (local7). Example this example shows how to enable the logging of s...

  • Page 1304

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1299 the system messages can also be logged to email recipients. This command does not take effect if the specified discriminator does not exist. Thus the default setting of the command is applied. Messages must enter the ...

  • Page 1306

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1301 parameters unit-id specifies the unit on which the attack log messages will be displayed. Index specifies the list of index numbers of the entries that need to be displayed. If no index is specified, all entries in th...

  • Page 1307

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1302 this command used to delete the attack log messages. Example this example shows how to delete all the attack log messages. Switch# clear attack-logging all switch#.

  • Page 1308

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1303 111. Time and sntp commands 111-1 clock set this command is used to manually set the system’s clock. Clock set hh:mm:ss day month year parameters hh:mm:ss specifies the current time in hours (24-hour format), minutes ...

  • Page 1309

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1304 no clock summer-time parameters recurring specifies that summer time should start and end on the specified week day of the specified month. Date specifies that summer time should start and end on the specified date of...

  • Page 1311

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1306 this example shows how to display the current time. Switch# show clock current time source : sntp current time : 18:20:04, 2013-07-04 time zone : utc +02:30 daylight saving time : recurring offset in minutes : 30 recu...

  • Page 1312

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1307 total entries:4 switch# 111-6 sntp server this command is used to allow the system clock to be synchronized with an sntp time server. To remove a server from the list of sntp servers, use the no form of this command. ...

  • Page 1313

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1308 111-7 sntp enable this command is used to enable the sntp function. Use the no form of this command to disable the sntp function. Sntp enable no sntp enable parameters none. Default by default, this option is disabled...

  • Page 1314

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1309 this command is used to set the polling interval. Example this example shows how to configure the interval to 100 seconds. Switch# configure terminal switch(config)# sntp interval 100 switch(config)#.

  • Page 1316

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1311 show time-range [name] parameters name (optional) specifies the name of the time-range profile to be displayed. Default none. Command mode user exec or any configuration mode. Command default level level: 1. Usage gui...

  • Page 1317

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1312 global configuration mode. Command default level level: 12. Usage guideline use this command to enter the time range configuration mode before using the periodic command to specify a time period. When a time-range is ...

  • Page 1318

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1313 113. Traffic segmentation commands 113-1 show traffic-segmentation forward this command is used to display the traffic segmentation for some ports or all ports. Show traffic-segmentation forward [interface interface-i...

  • Page 1320: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1315 114. Unicast reverse path forwarding (urpf) commands 114-1 ip urpf this command is used to enable unicast reverse path forwarding (urpf) checking globally. Use the no form of this command to disable the global state o...

  • Page 1321

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1316 parameters reachable-via (optional) specifies the mode how urpf examines the incoming packets. Any specifies to verify if the source address is present in the routing table (sometimes referred to as the loose mode). R...

  • Page 1322

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1317 switch# configure terminal switch(config)# interface ethernet 1/0/1 switch(config-if)# ip verify unicast source reachable-via any allow-default switch(config-if)# this example shows how to configure the ip acl, named ...

  • Page 1323

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1318 1/0/1 enabled any true v4gateway v6gateway 1/0/2 disabled rx false v6acl1 1/0/3 enabled rx true v4acl2 switch# display parameters urpf global state the global state of unicast rpf checking. Save and reboot required in...

  • Page 1324

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1319 115. Virtual lan (vlan) tunnel commands 115-1 dot1q inner ethertype this command is used to specify the system’s inner tpid. Use the no command to revert the setting to default. Dot1q inner ethertype value no dot1q in...

  • Page 1325

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1320 by default, this option is 0x8100. Command mode interface configuration mode. Command default level level: 12. Usage guideline an 802.1q tunnel port behaves as an uni port of a service vlan. The trunk ports which are ...

  • Page 1326

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1321 switch(config-if)# 115-4 switchport vlan mapping this command is used to specify the vlan translation entry for a trunk port or to specify the service vlan mapping entry for a dot1q tunnel port. Use the no command to ...

  • Page 1327

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1322 if the resultant-vlan parameter is specified in this command, the rule performs vlan translation. Once the vlan tag of the incoming packet matches the specified original vlan, the specified s-vlan replaces original vl...

  • Page 1328

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1323 parameters dot1q-vlan specifies the dot1q vlan id that is inserted to the untagged packets which are received on the dot1q tunnel port. Default none. Command mode interface configuration mode. Command default level le...

  • Page 1329

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1324 vlan of the received packets cannot match the vlan mapping entries or rules on this port, the received packets will be dropped. Example this example shows how to configure an interface port 1 to enable vlan mapping mi...

  • Page 1330

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1325 no vlan mapping profile id parameters id specifies the id of the vlan mapping profile. A lower id has a higher priority. The id range is from 1 to 1000. Type specifies the profile types. Different profiles can match d...

  • Page 1331

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1326 dst-mac mac-address specifies the destination mac address. Priority cos-value specifies the 802.1p priority. Inner-vid vlan-id specifies the inner vlan id. Ether-type value specifies the ethernet type. Src-ip network-...

  • Page 1332

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1327 115-10 switchport vlan mapping profile this command is used to apply the vlan mapping rules of a profile to the specified interface. Use the no form of the command to remove the association. Switchport vlan mapping pr...

  • Page 1333

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1328 parameters interface-id specifies the interface id. , (optional )specifies a series of interfaces, or separate a range of interfaces from a previous range. No space is allowed before and after the comma. - (optional) ...

  • Page 1334

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1329 none. Command mode user exec or any configuration mode. Command default level level: 1. Usage guideline this command is used to display the 802.1q tunneling configuration on interfaces. Example this example shows how ...

  • Page 1335

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1330 usage guideline use this command to display vlan mapping configurations. Example this example shows how to display all vlan mappings. Switch# show vlan mapping interface original vlan translated vlan priority status -...

  • Page 1336

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1331 rule 30 match src-ip 192.1.1.0/24, action dot1q-tunnel outer-vid 300, priority 0 total entries: 3 vlan mapping profile:2 type:ethernet rule 10 match src-mac 00-00-00-00-00-01,action translate outer-vid 40, priority 2 ...

  • Page 1337

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1332 116. Virtual lan (vlan) commands 116-1 acceptable-frame this command is used to set the acceptable types of frames by a port. Use the no form of the command to reset to the default setting. Acceptable-frame {tagged-on...

  • Page 1338

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1333 default by default, this option is enabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline use this command to enable ingress checking for packets received by the interface...

  • Page 1339

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1334 this example shows how to create a mac-based vlan id entry for the mac address 00-80-cc-00-00-11. Switch# configure terminal switch(config)# mac-vlan 00-80-cc-00-00-11 vlan 101 priority 4 switch(config)# 116-4 protoco...

  • Page 1340

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1335 protocol-vlan profile profile-id vlan vlan-id [priority cos-value] no protocol-vlan profile profile-id parameters profile-id specifies the id of the protocol group to be classified. Vlan-id specifies the vlan id of th...

  • Page 1341

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1336 network-mask ipv6 ipv6-network- prefix/prefix-length specifies the ipv6 network prefix and the prefix length. The prefix length of ipv6 network address cannot be greater than 64 bits. Priority cos-value (optional) spe...

  • Page 1342

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1337 command mode user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display the settings for vlan classification on a port based on the protocol group. Example this ex...

  • Page 1343

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1338 , (optional) specifies a series of interfaces, or separate a range of interfaces from a previous range. No space before and after the comma. - (optional) specifies a range of interfaces. No space before and after the ...

  • Page 1344

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1339 vlan mode : hybrid native vlan : 5 hybrid untagged vlan : 2,4,5,6 hybrid tagged vlan : 8,9,10 ingress checking : enabled acceptable frame type : admit-all dynamic tagged vlan : vlan precedence : mac-vlan eth1/0/4 vlan...

  • Page 1345

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1340 no switchport access vlan parameters access vlan vlan-id specifies the access vlan of the interface. Default by default, this access vlan is vlan 1. Command mode interface configuration mode. Command default level lev...

  • Page 1346

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1341 - (optional) specifies a range of vlans. No space is required before and after the hyphen. Default by default, a hybrid port is an untagged member port of vlan 1. Command mode interface configuration mode. Command def...

  • Page 1347

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1342 level: 12. Usage guideline when configuring the hybrid port join to its native vlan, use the switchport hybrid allowed vlan command to add the native vlan into its allowed vlan. The specified vlan does not need to exi...

  • Page 1348

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1343 when the switch-port mode is changed, the vlan related setting associated with previous mode will be lost. Example this example shows how to set the interface ethernet 1/0/1 as a trunk port. Switch# configure terminal...

  • Page 1349

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1344 switch# configure terminal switch(config)# interface ethernet 1/0/1 switch(config-if)# switchport mode trunk switch(config-if)# switchport trunk allowed vlan add 1000 switch(config-if)# 116-14 switchport trunk native ...

  • Page 1351

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1346 subnet-vlan specifies the port subnet-based vlan classification is precedence than mac-based vlan. Default by default, this option is mac-based vlan. Command mode interface configuration mode. Command default level le...

  • Page 1352

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1347 use this command to specify the name of a vlan. The vlan name must be unique within the administrative domain. Example this example shows how to configure the vlan name of vlan 1000 to be “admin-vlan”. Switch# configu...

  • Page 1353

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1348 this command is only valid for layer 2 vlan interface and it is used for products without proper hardware statistics resources per layer 2 vlan. This feature may share acl resources. Only physical port interfaces are ...

  • Page 1355: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1350 117. Virtual private lan service (vpls) commands 117-1 addition ac vlan this command is used to configure the addition vlan of the ac. Use the no command to delete the addition vlan. Addition ac vlan vlan-id no additi...

  • Page 1356

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1351 all specifies that all dynamic vpls mac address will be cleared. Vpls-name (optional) specifies the vpls name. This name can be up to 32 characters long. Peer (optional) specifies the peer in the vpls. Ip-address (opt...

  • Page 1357

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1352 command default level level: 12. Usage guideline this command can be used to configure tpid of the vlan tag of all pws belong to the vpls. If the vlan mode is addvlan or changevlan, the tpid of the modified vlan tag w...

  • Page 1358

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1353 117-5 mtu this command is used to configure the local ac link mtu value of a vpls. Use the no form of the command to restore the default setting. Mtu value no mtu parameters value specifies the local ac link’s mtu val...

  • Page 1359

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1354 by default, each vc has a default name composed by a fixed prefix of “vc” plus the vc-id/peer-address. For example, vc8/5.5.5.5. Command mode neighbor configuration mode. Command default level level: 12. Usage guideli...

  • Page 1360

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1355 usage guideline this command is used to create a peer in a vpls. Use the no command to delete a peer from a vpls. Example this example shows how to create a peer, which an ip address of 2.2.2.2 and a vc id of 100. It ...

  • Page 1361

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1356 when the backup pw is changed from link-standby to link-up, the mac withdraw message with a null mac list will be sent from mtu-s to the pe via the backup pw to clear old mac addresses. When the primary pw is back to ...

  • Page 1362

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1357 switch# configure terminal switch(config)# l2 vfi vpls100 manual switch(config-vfi)# pw-type raw switch(config-vfi)# 117-10 show mac-address-table vpls this command is used to display vpls mac address information. Sho...

  • Page 1363

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1358 vpls100 00-08-a1-79-9a-e5 101/1.1.1.1 vpls100 00-08-a1-79-9a-e6 101/1.1.1.1 total entries: 8 switch# 117-11 show mpls l2transport vc this command is used to display vc information for vpws and vpls. Show mpls l2transp...

  • Page 1364

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1359 name: vc5/120.1.1.2 description: local ac: vpls101, status: up vlan mode: default, 802.1q tunneling ethernet type: 0x8100 remote ac status: up mpls vc labels: local 19, remote 19 outbound tunnel label: 103 mtu: local ...

  • Page 1365

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1360 vpls name vpn id peers/acs oper status -------------------------------- ---------- --------- ----------- vpls100 100 3/1 up vpls101 101 3/1 up vpls102 102 3/1 up vpls103 103 3/1 up vpls104 104 3/1 up vpls105 105 3/1 u...

  • Page 1366

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1361 switch# show vpls vpls102 detail vpls name: vpls102, operate status: up vpls id: 102, service type: tagged, mtu: 1500 vlan mode: default, 802.1q tunneling ethernet type: 0x8100 peers via pseudowires: vc id peer type o...

  • Page 1367

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1362 the vlan mode will affect the vlan handling of the encapsulated packet for all pws that belong to this vpls. The tpid of the added or changed vlan tag can be configured with the dot1q tunneling ethertype command. This...

  • Page 1368

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1363 no xconnect vfi vpls-name parameters vpls-name (optional) specifies the vpls name. This name can be up to 32 characters long. Default none. Command mode interface configuration mode. Command default level level: 12. U...

  • Page 1369: Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1364 118. Virtual private wire service (vpws) commands 118-1 addition ac vlan this command is used to configure the addition vlan of the ac. Use the no command to delete the addition vlan. Addition ac vlan vlan-id no addit...

  • Page 1370

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1365 ip-address specifies the peer lsr id that is used to identify the other end provider edge (pe). Vc-id specifies the pw service instance id. It is used to uniquely identify the vpws and it must be unique at both pes. T...

  • Page 1371

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1366 switch(config-if-xconn)# 118-3 dot1q tunneling ethertype this command is used to configure the tpid of the vlan tag to be added or changed for the encapsulated packet. Dot1q tunneling ethertype value no dot1q tunnelin...

  • Page 1372

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1367 identified. Remote-label specifies the output label used to encapsulate the packet transmitted to the pw. Default none. Command mode xconnect configuration mode. Command default level level: 12. Usage guideline this c...

  • Page 1373

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1368 level: 12. Usage guideline this command is used to configure the name of a vc. The vc name must be unique in all l2vcs example this example shows how to configure the name of a vc. Switch# configure terminal switch(co...

  • Page 1374

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1369 type lsp ping. For pws using ldp as the signaling method, the cc type and cv type is negotiated by ldp. If the peer received the request message, it will reply the request message sender with mpls echo reply message. ...

  • Page 1375

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1370 level: 12. Usage guideline issuing this command will create or enter the interface service configuration mode with a specified encapsulation service vlan id. The user can further configure the vpls or vpws ac using th...

  • Page 1376

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1371 total entries: 4 switch# this example shows how to display detailed information of vc 1. Switch# show mpls l2transport vc 1 detail vc id: 1, peer ip address: 150.1.1.4, operate status: up name: vc_to_pe2 description: ...

  • Page 1377

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1372 vc statistics: rx bytes: 0, rx packets: 0 tx bytes: 0, tx packets: 0 vc id: 4, peer ip address: 160.1.1.2, operate status: standby, backup name: backup_vc_to_pe2 description: this is backup vc to pe2 backup delay: nev...

  • Page 1378

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1373 by default, no change is applied to port and vlan-based acs and the vlan tag 0 is added for port- based acs. Command mode xconnect configuration mode. Command default level level: 12. Usage guideline use this command ...

  • Page 1379

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1374 interface configuration mode. Command default level level: 12. Usage guideline use this command to create a vpws service and enter the xconnect configuration mode. When creating the vpws on a physical port or link agg...

  • Page 1380: (Vrrp) Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1375 119. Virtual router redundancy protocol (vrrp) commands 119-1 snmp-server enable traps vrrp this command is used to enable the vrrp trap function in snmp. Use the no command to disable this function. Snmp-server enabl...

  • Page 1381

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1376 parameters string specifies the plain text authentication password. This string can be up to 16 characters long. Default by default, no authentication is used. Command mode interface configuration mode. Command defaul...

  • Page 1382

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1377 this command creates a virtual router and specifies the ip address for the virtual router. All routers in the same vrrp group must be configured with the same virtual router id and ip address. A virtual router group i...

  • Page 1383

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1378 119-5 vrrp timers advertise this command is used to configure the interval between successive vrrp advertisements by the master router. To restore the default value, use the no form of this command. Vrrp vrid timers a...

  • Page 1384

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1379 vrid specifies the virtual router identifier that identifies the vrrp group. The valid range is from 1 to 255. Default by default, the preempt mode is used. Command mode interface configuration mode. Command default l...

  • Page 1385

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1380 this command configures the vrrp group’s bfd peer address. This ip address must be a real ip address of a real device in the same vrrp virtual group. A bfd session will be created between this vrrp router and its peer...

  • Page 1386

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1381 this command is used to configure the critical ip address of a virtual router. Use the no form of this command to remove the critical ip address. Vrrp vrid track critical-ip ip-address no vrrp vrid track critical-ip p...

  • Page 1387

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1382 user exec or any configuration mode. Command default level level: 1. Usage guideline use this command to display the vrrp related setting and status. Example this example shows how to display the vrrp status for all i...

  • Page 1388

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1383 switch# 119-11 show vrrp brief this command is used to display the vrrp brief information. Show vrrp brief parameters none. Default none. Command mode user exec or any configuration mode. Command default level level: ...

  • Page 1389

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1384 vrouter ip the ip address of the virtual router..

  • Page 1390: Lite) Commands

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1385 120. Virtual routing and forwarding lite (vrf- lite) commands 120-1 address-family ipv4 vrf this command is used to enter the vrf address family configuration mode. Use the no form of this command to remove the vrf ad...

  • Page 1391

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1386 parameters route-map specifies the name of import route map of the vrf. Default none. Command mode vrf configuration mode. Command default level level: 12. Usage guideline this command is used to configure the import ...

  • Page 1392

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1387 example this example shows how to create and delete a vrf instance. Switch# configure terminal switch(config)# ip vrf vpn-a switch(config-vrf)# exit switch(config)# no ip vrf vpn-a switch(config)# 120-4 ip vrf forward...

  • Page 1393

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1388 no maximum routes parameters limit specifies the maximum number of routes within the vrf. Its range is from 1 to 16384. Warn-threshold specifies the warning threshold value in percentage. A notification message will b...

  • Page 1394

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1389 command default level level: 12. Usage guideline this command is used to configure the vrf’s route distinguisher to form a unique vpn-ipv4 prefix. One vrf has only one route distinguisher and cannot be changed if it h...

  • Page 1395

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1390 this example shows how to create a vrf instance vpn-a and add import and export targets. Switch# configure terminal switch(config)# ip vrf vpn-a switch(config-vrf)# route-target import 100:1 switch(config-vrf)# route-...

  • Page 1396

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1391 ip100 export vpn route-target communities: rt:100:1 import vpn route-target communities: rt:100:1 import route-map: rmap1 route warning limit 5, current count 0 switch# this example shows how to check interfaces assoc...

  • Page 1397

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1392 121. Web authentication commands 121-1 web-auth enable this command is used to enable the web authentication function on the port. Use the no form of this command to disable the web authentication function. Web-auth e...

  • Page 1398

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1393 maximum number can be up to 64 characters. Username-title string specifies the user name title of web authentication login window. The maximum number can be up to 32 characters. Password-title string specifies the pas...

  • Page 1399

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1394 web-auth success redirect-path string no web-auth success redirect-path parameters string specifies the default url the client web browser will be redirected to after successful authentication. If no default redirect ...

  • Page 1400

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1395 usage guideline web authentication is a feature designed to authenticate a user by using the web browser when the user is trying to access the internet via the switch. The switch itself can be the authentication serve...

  • Page 1401

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1396 this example shows how to configure the web authentication virtual ipv4 to be “1.1.1.1” and the fqdn url to be “www.Website4.Co”. Switch# configure terminal switch(config)# web-auth virtual-ip ipv4 1.1.1.1 switch(conf...

  • Page 1403

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1398 specified, the default threshold setting is used. Default by default, this option is disabled. Command mode interface configuration mode. Command default level level: 12. Usage guideline when a packet arrives, the cur...

  • Page 1404

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1399 interface configuration mode. Command default level level: 12. Usage guideline wred drops packets, based on the average queue size exceeding a specific threshold, to indicate congestion. Ecn is an extension to wred in...

  • Page 1405

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1400 the default exponential weight factor is 9. Command mode interface configuration mode. Command default level level: 12. Usage guideline this command is used to configure the wred exponential weight factor for the aver...

  • Page 1406

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1401 command default level level: 12. Usage guideline different types of packets can be queued in different bucket lists and different list can be specified with different threshold values. Example this example shows how t...

  • Page 1407

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1402 current wred configuration: eth1/0/1 cos wred state exp-weight-constant profile --- ---------- ------------------- ------- 0 enabled 9 1 1 enabled 9 1 2 enabled 9 1 3 enabled 9 1 4 enabled 9 1 5 enabled 9 1 6 enabled ...

  • Page 1408

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1403 122-8 show random-detect profile this command is used to display the wred profile setting. Show random-detect profile [profile id] parameters profile id (optional) specifies the wred profile id that will be displayed....

  • Page 1409

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1404 appendix a - password recovery procedure this section describes the procedure for resetting passwords on the d-link dxs-3600 series switch. Authenticating any user who tries to access networks is necessary and importa...

  • Page 1410

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1405 appendix b - system log entries the following table lists all possible entries and their corresponding meanings that will appear in the system log of this switch. 802.1x log description severity event description: 802...

  • Page 1411

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1406 exec-type: it indicates the exec types, e.G.: console, telnet, ssh, web, web(ssl). Client-ip: it indicates the client’s ip address if valid through ip protocol. Aaa-method: it indicates the authentication method, e.G....

  • Page 1412

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1407 event description: this log will be generated when radius assigned a valid vlan id attributes. Log message: radius server assigned vid: to port id> (username: ) parameters description: server-ip: it indicates the radi...

  • Page 1413

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1408 event description: bgp connection is normally closed. Log message: bgp-6-normalclose: bgp connection is normally closed (peer:). Parameters description: ipaddr: ip address of bgp peer. Informational event description:...

  • Page 1414

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1409 log message: bgp-6-totalpfxmax: the total number of prefix received reaches max prefix limit. Event description: bgp received unnecessary as4-path attribute from new (4- bytes as) bgp peer log message: bgp-4-rcvunnece...

  • Page 1415

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1410 cfm log description severity event description: cross-connect is detected log message: cfm cross-connect. Vlan:, local(md level:, interface:, direction:) remote(mepid:, mac:) parameters description: vlanid: represents...

  • Page 1416

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1411 mdlevel: represents the md level of the mep. Interface-id: represents the interface number of the mep. Mepdirection: represents the mep direction, which can be "inward" or "outward". Mepid: represents the mepid of the...

  • Page 1417

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1412 mepdirection: represents the direction of the mep. This can be "inward" or "outward". Mepid: represents the mepid of the mep. Event description: lck condition cleared log message: lck condition cleared. Md level:, vla...

  • Page 1418

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1413 unitid: the unit id. Session: the user’s session. Username: represent current login user. Ipaddr: represent client ip address. Macaddr : represent client mac address. Event description: configuration downloaded succes...

  • Page 1419

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1414 threshold [exceedtype] parameters description: interface-id: the port number. Component: the ddm threshold type. The value should be one of the following values: temperature, supply voltage, bias current, tx power, rx...

  • Page 1420

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1415 event description: the ipv6 address obtained from a dhcpv6 server starts rebinding log message: the ipv6 address on interface starts rebinding. Parameters description: ipv6address: ipv6 address obtained from a dhcpv6 ...

  • Page 1421

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1416 rebinding. Parameters description: ipv6address: ipv6 prefix obtained from a delegation router. Intf-name: name of the dhcpv6 client pd interface. Event description: the ipv6 prefix obtained from a delegation router re...

  • Page 1422

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1417 : activation code event description: license expired. Log message: license expired (license:, ac: ). Parameters description: : license model name. : activation code critical event description: license successfully ins...

  • Page 1423

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1418 parameters description: type: the type of arp packet, it indicates that arp packet is request or arp response. Event description: this log will be generated when dai detect valid arp packet. Log message: legal arp pac...

  • Page 1424

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1419 parameters description: ip: the broadcast ip destination address. Event description: ip directed-broadcast rate exceed 100 packets per second log message: ip directed broadcast rate is high. Parameters description: in...

  • Page 1425

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1420 log message: loop vlan numbers overflow. Parameters description: lldp-med log description severity event description: lldp-med topology change detected log message: lldp-med topology change detected (on port . Chassis...

  • Page 1426

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1421 chassisid: chassis id. Porttype: port id subtype. Value list: 1. Interfacealias(1) 2. Portcomponent(2) 3. Macaddress(3) 4. Networkaddress(4) 5. Interfacename(5) 6. Agentcircuitid(6) 7. Local(7) portid: port id. Device...

  • Page 1427

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1422 username: represent current login user. Event description: login through console unsuccessfully. Log message: [unit , ] login failed through console (username: ) parameters description: unitid: the unit id. Username: ...

  • Page 1428

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1423 parameters description: username: represent current login user. Ipaddr: represent client ip address. Event description: ssh session timed out. Log message: ssh session timed out (username: , ip: ) parameters descripti...

  • Page 1429

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1424 parameters description: interface-id: the interface on which the host is authenticated. Event description: the authorized user number on an interface is below the maximum user limit in a time interval. Log message: re...

  • Page 1431

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1426 event description: spanning tree mst configuration id name and revision level changed. Log message: spanning tree mst configuration id name and revision level change (name: ,revision level ). Parameters description: n...

  • Page 1432

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1427 log message: ospf-5-nbrfulltodown: ospf nbr on interface name> changed state from full to down parameters description: intf-name: name of ospf interface. Nbr-id: neighbor's router id. Event description: one ospf neigh...

  • Page 1433

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1428 thermal-sensor-descr: the sensor id and position. Degree: the current temperature. Event description: temperature recovers to normal. Log message: unit temperature back to normal parameters description: unitid: the un...

  • Page 1434

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1429 intf-name: interface name. Safeguard log description severity event description: when the cpu utilization is over the rising threshold, the switch enters exhausted mode. Log message: unit , safeguard engine enters exh...

  • Page 1435

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1430 log message: unit: , mac: hot insertion. Parameters description: unitid: box id. Macaddr: mac address. Event description: hot removal. Log message: unit: , mac: hot removal. Parameters description: unitid: box id. Mac...

  • Page 1436

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1431 parameters description: interface-id: the interface name. Event description: multicast storm cleared. Log message: multicast storm has cleared. Parameters description: interface-id: the interface name. Informational e...

  • Page 1437

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1432 vpws log description severity event description: pseudo-wire link down log message: pseudo-wire id peer ip link down parameters description: vc_id: the link down pseudo-wire id ipaddr: the peer ip address of the link ...

  • Page 1438

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1433 event description: authentication type mismatch of one received vrrp advertisement message. Log message: vrrp-4-authtypemis:authentication type mismatch on vr id> at interface parameters description: vr-id: vrrp virtu...

  • Page 1439

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1434 vrrp-ip-addr: vrrp virtual ip address vrrp-mac-addr: vrrp virtual mac address event description: a virtual mac address is deleting from switch l3 table. Log message: vrrp-5-macl3del: deleted a virtual ip mac from l3 t...

  • Page 1440

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1435 vrrp-mac-addr: vrrp virtual mac address mac-box: stacking box number of vrrp virtual mac. Event description: failed when adding a virtual mac into switch chip’s l3 table. Log message: vrrp-3-macl3addfail: failed to ad...

  • Page 1441

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1436 event description: login failed through web (ssl). Log message: login failed through web (ssl) (username: , ip: ). Parameters description: username: the use name that used to login ssl server. Ipaddr: the ip address o...

  • Page 1442: Appendix C - Trap Entries

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1437 appendix c - trap entries the following table lists all possible trap log entries and their corresponding meanings that will appear in the switch. 802.1x trap name description oid ddot1xextloggedsuccess the trap is se...

  • Page 1443

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1438 cfm trap name description oid dot1agcfmfaultalarm this trap is initiated when a connectivity defect is detected. Binding objects: (1) dot1agcfmmephighestprdefect 1.3.111.2.802 .1.1.8.0.1 cfm extension trap name descri...

  • Page 1444

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1439 (4) ddhcpfilterlogbufferoccurtime dos prevention trap name description oid ddospreveattackdetectedpacke t the trap is sent when detect dos attack. Binding objects: (1) ddosprevctrlattacktype (2) ddosprevnotiinfodropip...

  • Page 1445

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1440 lacp trap name description oid linkup a linkup trap signifies that the snmp entity, acting in an agent role, has detected that the ifoperstatus object for one of its communication links left the down state and transit...

  • Page 1446

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1441 trap name description oid mplsldpinitsessionthresholdex ceeded this notification is generated when the backoff is enabled, and the number of session initialization messages exceeds the value of the 'mplsldpentityinits...

  • Page 1447

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1442 binding objects: (1) ifindex, (2) dnasessionclientmacaddress (3) dnasessionauthvlan dmacauthloggedagesout the trap is sent when a mac-based access control host ages out. Binding objects: (1) ifindex, (2) dnasessioncli...

  • Page 1448

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1443 trap name description oid linkup a notification is generated when port linkup. Binding objects: (1) ifindex, (2) if adminstatus (3) ifoperstatu 1.3.6.1.6.3.1. 1.5.4 linkdown a notification is generated when port linkd...

  • Page 1449

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1444 safeguard trap name description oid dsafeguardchgtoexhausted this trap indicates system change operation mode from normal to exhaust. Binding objects: (1) dsafeguardenginecurrentmode 1.3.6.1.4.1.17 1.14.19.1.1.0. 1 ds...

  • Page 1450

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1445 storm control trap name description oid dstormctrloccurred this trap is sent when dstormctrlnotifyenable is 'stormoccurred' or 'both' and a storm is detected. Binding objects: (1) ifindex, (2) dstormctrlnotifytraffict...

  • Page 1451

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1446 web authentication trap name description oid dwebauthloggedsuccess the trap is sent when a host has successfully logged in (passed web-authentication). Binding objects: (1) ifindex (2) dnasessionauthvlan (3) dnasessio...

  • Page 1452

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1447 appendix d - radius attributes assignment the radius attributes assignment on the dxs-3600 is used in the following modules: console, telnet, ssh, web, 802.1x, mac-based access control, and wac. The description that f...

  • Page 1453

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1448 authenticates successfully, the device will not assign any bandwidth to the port. If the bandwidth attribute is configured on the radius server with a value of “0”, the effective bandwidth will be set “no_limited”, an...

  • Page 1454

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1449 tag field value string field format 0x01 vlan name (ascii) 0x02 vlan id (ascii) others (0x00, 0x03 ~ 0x1f, >0x1f) when the switch receives the vlan setting string, it will think it is the vlan id first. In other words...

  • Page 1455

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1450 appendix e - ietf radius attributes support remote authentication dial-in user service (radius) attributes carry specific authentication, authorization, information and configuration details for the request and reply....

  • Page 1456

    Dxs-3600 series layer 3 managed 10gigabit ethernet switch cli reference guide 1451 80 message-authenticator 81 tunnel-private-group-id 85 acct-interim-interval 87 nas-port-id 95 nas-ipv6-address radius accounting attributes: number ietf attribute 1 user-name 4 nas-ip-address 5 nas-port 6 service-typ...