1. DL manuals
  2. D-Link
  3. Switch
  4. TM DES-6500
  5. Cli Manual

D-Link TM DES-6500 Cli Manual

Manual is about: Modular Layer 3 Chassis Ethernet Switch

Summary of TM DES-6500

  • Page 1

    Product model : tm des-6500 modular layer 3 chassis ethernet switch release 3 cli manual.

  • Page 2: Table of Contents

    Table of contents introduction ............................................................................................................................................ 1 using the console cli ...........................................................................................................

  • Page 3

    Dvmrp commands............................................................................................................................. 290 pim commands................................................................................................................................... 295 ip multi...

  • Page 4

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 1 i ntroduction the xstack des-6500 layer 3 modular chassis ethernet switch is a member of the d-link xstack family. Ranging from 10/100mbps edge switches to core gigabit switches, the xstack switch family has been future-proof desig...

  • Page 5

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual there is no initial username or password. Just press the enter key twice to display the cli input cursor − des-6500:4# . This is the command line where all commands are input. Setting the switch’s ip address each switch must be assig...

  • Page 6

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual figure 1-3. Assigning an ip address in the above example, the switch was assigned an ip address of 10.53.13.144 with a subnet mask of 255.0.0.0. The system message success indicates that the command was executed successfully. The swi...

  • Page 7: Cli

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 2 u sing the c onsole cli the xstack des-6500 supports a console management interface that allows the user to connect to the switch’s management agent via a serial port and a terminal or a computer running a terminal emulation progra...

  • Page 8

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual figure 2-1. Initial console screen commands are entered at the command prompts, des-6500:4# . There are a number of helpful features included in the cli. Entering the ? Command will display a list of all of the top-level commands. Fi...

  • Page 9

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual figure 2-3. Example command parameter help in this case, the command config account was entered with the parameter . The cli will then prompt to enter the with the message, next possible completions: . Every command in the cli has th...

  • Page 10

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual if a command is entered that is unrecognized by the cli, the top-level commands will be displayed under the available commands: prompt. Figure 2-5. The available commands prompt the top-level commands consist of commands such as show...

  • Page 11

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 3 c ommand s yntax the following symbols are used to describe how command entries are made and values and arguments are specified in this manual. The online help contained in the cli and available through the console interface uses t...

  • Page 15

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#config account dlink command: config account dlink enter a old password:**** enter a case-sensitive new password:**** enter the new password again for confirmation:**** success. Des-6500:4# show account purpose used to dis...

  • Page 16

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#delete account system command: delete account system are you sure to delete the last administrator account?(y/n)y success. Des-6500:4# example usage: to delete the user account “system2”: des-6500:4#delete account system2 ...

  • Page 17

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual command: show config config_in_nvram #------------------------------------------------------------------------------------------------------ # des-6500 configuration # # firmware: build 3.00-b29 # copyright(c) 2004-2007 d-link corpor...

  • Page 18

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show switch purpose used to display information about the switch. Syntax show switch description this command displays information about the switch. Parameters none. Restrictions none. Example usage: to display the switch information...

  • Page 19

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show device_status purpose used to display the current status of the hardware of the switch. Syntax show device_status description this command displays the current status of the switch’s physical elements. Parameters none. Restricti...

  • Page 21

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#enable clipaging command: enable clipaging success. Des-6500:4# disable clipaging purpose used to disable the pausing of the console screen scrolling at the end of each page when the show command displays more than one scr...

  • Page 22

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual disable telnet purpose used to disable the telnet protocol on the switch. Syntax disable telnet description this command is used to disable the telnet protocol on the switch. Parameters none. Restrictions only administrator-level use...

  • Page 23

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual disable web purpose used to disable the http-based management software on the switch. Syntax disable web description this command disables the web-based management software on the switch. Parameters none. Restrictions only administra...

  • Page 24

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual reboot purpose used to restart the switch. Syntax reboot description this command is used to restart the switch. Parameters none. Restrictions none. Example usage: to restart the switch: des-6500:4#reboot command: reboot are you sure...

  • Page 25

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual login purpose used to log in a user to the switch’s console. Syntax login description this command is used to initiate the login procedure. The user will be prompted for his username and password. Parameters none. Restrictions none. ...

  • Page 26

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config command_prompt switch. Default – entering this parameter will return the command prompt to its original factory default setting. Restrictions the reset command will not alter the configured command prompt, yet the reset system...

  • Page 27

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#config greeting_message command: config greeting_message greeting messages editor =============================================================================== des-6500 chassis ethernet switch command line interface firm...

  • Page 29

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config ports from the master . If one connection is set for 1000 master , the other side of the connection must be set for 1000 slave . Any other configuration will result in a link down status for both ports. None denotes the switch...

  • Page 30

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show ports command: show ports port port settings connection address state speed/duplex/flowctrl speed/duplex/flowctrl learning ------ -------- --------------------- --------------------- -------- 1:1 enabled auto/enabled ...

  • Page 32

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to configure the port security: des-6500:4#config port_security ports 5:1-5:5 admin_state enabled max_learning_addr 5 lock_address_mode deleteonreset command: config port_security ports 5:1-5:5 admin_state enabled max_...

  • Page 33

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual delete port_security_entry_vlan_name purpose used to delete an entry from the switch’s port security settings. Syntax delete port_security_entry_vlan_name port mac_address description this command is used to remove an entry from the ...

  • Page 34: (Snmp) C

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 7 n etwork m anagement (snmp) c ommands the network management commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. The xstack des-6500 support the simple network man...

  • Page 36

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create snmp user encryption − scrambles the contents of messages to prevent it from being viewed by an unauthorized source. Parameters − an alphanumeric name of up to 32 characters that will identify the new snmp user. − an alphanume...

  • Page 37

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create snmp user the agent. • - enter an alphanumeric key string of exactly 32 characters, in hex form, that will be used to encrypt the contents of messages the host sends to the agent. None – adding this parameter will add no encry...

  • Page 38

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show snmp user purpose used to display information about each snmp username in the snmp group username table. Syntax show snmp user description the show snmp user command displays information about each snmp username in the snmp grou...

  • Page 39

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#create snmp view dlinkview 1.3.6 view_type included command: create snmp view dlinkview 1.3.6 view_type included success. Des-6500:4# delete snmp view purpose used to remove an snmp view entry previously created on the swi...

  • Page 40

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual command: show snmp view vacm view table settings view name subtree view type -------------------- ------------------------- ---------- readview 1 included writeview 1 included notifyview 1.3.6 included restricted 1.3.6.1.2.1.1 includ...

  • Page 41

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to create the snmp community string “dlink:” des-6500:4#create snmp community dlink view readview read_write command: create snmp community dlink view readview read_write success. Des-6500:4# delete snmp community purp...

  • Page 42

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to display the currently entered snmp community strings: des-6500:4#show snmp community command: show snmp community snmp community table community name view name access right ------------------------------ -----------...

  • Page 43

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to display the current name of the snmp engine on the switch: des-6500:4#show snmp engineid command: show snmp engineid snmp engine id : 0035636666 des-6500:4# create snmp group purpose used to create a new snmp group, or a table tha...

  • Page 44

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create snmp group be encrypted. Read_view – specifies that the snmp group being created can request snmp messages. Write_view – specifies that the snmp group being created has write privileges. − an alphanumeric string of up to 32 ch...

  • Page 45

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show snmp groups purpose used to display the group-names of snmp groups currently configured on the switch. The security model, level, and status of each group are also displayed. Syntax show snmp groups description the show snmp gro...

  • Page 46

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual readview name : restricted writeview name : notify view name : restricted security model : snmpv3 security level : noauthnopriv group name : readgroup readview name : communityview writeview name : notify view name : communityview se...

  • Page 47

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create snmp host of management information (smi) and adds some security features. V3 – specifies that the snmp version 3 will be used. Snmp v3 provides secure access to devices through a combination of authentication and encrypting p...

  • Page 48

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to delete an snmp host entry: des-6500:4#delete snmp host 10.48.74.100 public command: delete snmp host 10.48.74.100 public success. Des-6500:4# show snmp host purpose used to display the recipient of snmp traps genera...

  • Page 49

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create trusted_host parameters − the ip address of the trusted host. Restrictions only administrator-level users can issue this command. Example usage: to create the trusted host: des-6500:4#create trusted_host 10.48.74.121 command: ...

  • Page 50

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to delete a trusted host with an ip address 10.48.74.121: des-6500:4#delete trusted_host 10.48.74.121 command: delete trusted_host 10.48.74.121 success. Des-6500:4# enable snmp traps purpose used to enable snmp trap su...

  • Page 51

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show snmp traps purpose used to show snmp trap support on the switch . Syntax show snmp traps description this command is used to view the snmp trap support status currently configured on the switch. Parameters none. Restrictions onl...

  • Page 52

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to disable the snmp authentication trap support: des-6500:4#disable snmp authenticate_traps command: disable snmp authenticate_traps success. Des-6500:4# config snmp system_contact purpose used to enter the name of a c...

  • Page 53

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to configure the switch location for “ hq 5f ”: des-6500:4#config snmp system_location hq 5f command: config snmp system_location hq 5f success. Des-6500:4# config snmp system_name purpose used to configure the name for the switch. S...

  • Page 54

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#enable rmon command: enable rmon success. Des-6500:4# disable rmon purpose used to disable rmon on the switch. Syntax disable rmon description this command is used, in conjunction with the enable rmon command above, to ena...

  • Page 56

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual download increment − allows the download of a partial switch configuration file. This allows a file to be downloaded that will change only the switch parameters explicitly stated in the configuration file. All other switch parameters...

  • Page 57

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#upload cfg_totftp 10.48.74.121 c:\cfg\log.Txt command: upload cfg_to tftp 10.48.74.121 c:\cfg\log.Txt connecting to server................... Done. Upload configuration...................Done. Des-6500:4# ping purpose used...

  • Page 58

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual traceroute parameters - specifies the ip address of the host. Ttl - the time to live value of the trace route request. This is the maximum number of routers the traceroute command will cross while seeking the network path between two...

  • Page 59

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual note: dual-purpose (dhcp/tftp) server utility software may require entry of the configuration file name and path within the user interface. Alternatively, the dhcp software may require creating a separate ext file with the configurat...

  • Page 60

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual disable autoconfig purpose use this to deactivate autoconfiguration from dhcp. Syntax disable autoconfig description this instructs the switch not to accept autoconfiguration instruction from the dhcp server. This does not change the...

  • Page 61

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 9 n etwork m onitoring c ommands the network monitoring commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters show packet ports show error ports sho...

  • Page 62

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show packet ports parameters − specifies a range of ports to be displayed. The port list is specified by listing the lowest slot number and the beginning port number on that slot, separated by a colon. Then the highest slot number, a...

  • Page 63

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to display the errors of the port 3 of module 1: des-6500:4#show errors ports 1:3 command: show errors ports 1:3 rx frames tx frames --------------- ---------------- crc error 19 excessive deferral 0 undersize 0 crc er...

  • Page 64

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show utilization ports command: show utilization ports port tx/sec rx/sec util port tx/sec rx/sec util ---- ---------- ---------- ---- ---- ---------- ---------- ---- 1:1 0 0 0 2:10 0 0 0 1:2 0 0 0 2:11 0 0 0 1:3 0 0 0 2:1...

  • Page 65

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show stack_information command: show stack_information box prio- prom runtime h/w id type exist rity version version version --- ----------- ----- ----- -------- -------- -------- 1 des-6507 exist 16 2.00-b20 3.00-b29 1a1 ...

  • Page 66

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual clear log purpose used to clear the switch’s history log. Syntax clear log description this command will clear the switch’s history log. Parameters none. Restrictions only administrator-level users can issue this command. Example usa...

  • Page 67

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual enable syslog purpose used to enable the system log to be sent to a remote host. Syntax enable syslog description the enable syslog command enables the system log to be sent to a remote host. Parameters none. Restrictions only admini...

  • Page 68

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show syslog purpose used to display the syslog protocol status as enabled or disabled. Syntax show syslog description the show syslog command displays the syslog status as enabled or disabled. Parameters none. Restrictions none. Exam...

  • Page 69

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create syslog host facility − some of the operating system daemons and processes have been assigned facility values. Processes and daemons that have not been explicitly assigned a facility may use any of the "local use" facilities or...

  • Page 71

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config syslog host warning − specifies that warning messages will be sent to the remote host. This corresponds to number 4 from the list above. All − specifies that all of the currently supported syslog messages that are generated by...

  • Page 72

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config syslog host remote host. This corresponds to number 23 from the list above. Udp_port − specifies the udp port number that the syslog protocol will use to send messages to the remote host. Ipaddress − specifies the ip address o...

  • Page 73

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config syslog host all severity − severity level indicator, as described below: bold font indicates that the corresponding severity level is currently supported on the switch. Numerical severity code 0 emergency: system is unusable 1...

  • Page 74

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config syslog host all local0 − specifies that local use 0 messages will be sent to the remote host. This corresponds to number 16 from the list above. Local1 − specifies that local use 1 messages will be sent to the remote host. Thi...

  • Page 77

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#config system_severity trap critical command: config system_severity trap critical success. Des-6500:4# show system_severity purpose to display the current severity settings set on the switch. Syntax show system_severity d...

  • Page 78: (Mstp) C

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 10 m ultiple s panning t ree p rotocol (mstp) c ommands this switch supports three versions of the spanning tree protocol; 802.1d stp, 802.1w rapid stp and 802.1s mstp. Multiple spanning tree protocol, or mstp, is a standard defined ...

  • Page 81

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config stp values consistent with other devices on the bridged lan. If the value ages out and a bpdu has still not been received from the root bridge, the switch will start sending its own bpdu to all other switches for permission to...

  • Page 84

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to create a spanning tree instance 2: des-6500:4#create stp instance_id 2 command: create stp instance_id 2 success. Des-6500:4# config stp instance_id purpose used to add or delete an stp instance id. Syntax config st...

  • Page 85

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#config stp instance_id 2 remove_vlan 10 command : config stp instance_id 2 remove_vlan 10 success. Des-6500:4# delete stp instance_id purpose used to delete a stp instance id from the switch. Syntax delete stp instance_id ...

  • Page 86

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to set the priority value for instance_id 2 as 4096: des-6500:4#config stp priority 4096 instance_id 2 command : config stp priority 4096 instance_id 2 success. Des-6500:4# config stp mst_config_id purpose used to upda...

  • Page 87

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config stp mst_ports higher priority value for interfaces to be selected for forwarding first. In instances where the priority value is identical, the mstp function will implement the lowest port number into the forwarding state and ...

  • Page 88

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show stp purpose used to display the switch’s current stp configuration. Syntax show stp description this command displays the switch’s current stp configuration. Parameters none. Restrictions none. Example usage: to display the stat...

  • Page 89

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual max age : 20 tx hold count : 3 forwarding bpdu : enabled loopback detection : enabled lbd recover time : 60 des-6500:4# show stp ports purpose used to display the switch’s current instance_id configuration. Syntax show stp ports desc...

  • Page 90

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show stp instance_id configuration for the cist internally set on the switch. Restrictions none. Example usage: to display the stp instance configuration for instance 0 (the internal cist) on the switch: des-6500:4#show stp instance_...

  • Page 91

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show stp mst_config_id command: show stp mst_config_id current mst configuration identification ---------------------------------------- configuration name : 00:53:13:1a:33:24 revision level :0 msti id vid list ------- ---...

  • Page 92

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 11 f orwarding d atabase c ommands the forwarding database commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create fdb port create multicast_fd...

  • Page 93

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#create fdb default 00-00-00-00-01-02 port 2:5 command: create fdb default 00-00-00-00-01-02 port 2:5 success. Des-6500:4# create multicast_fdb purpose used to create a static entry to the multicast mac address forwarding t...

  • Page 94

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config multicast_fdb − specifies a range of ports to be displayed the beginning port number on that slot, separated by a colon. Then the highest slot number, and the highest port number of the range (also separated by a colon) are sp...

  • Page 95

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config fdb aging_time purpose used to set the aging time of the forwarding database. Syntax config fdb aging_time description the aging time affects the learning process of the switch. Dynamic forwarding table entries, which are made...

  • Page 96

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#delete fdb default 00-00-00-00-01-02 command: delete fdb default 00-00-00-00-01-02 success. Des-6500:4# example usage: to delete a multicast fdb entry: des-6500:4#delete fdb default 01-00-00-00-01-02 command: delete fdb de...

  • Page 98

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to display unicast mac address table: des-6500:4#show fdb command: show fdb unicast mac address aging time = 300 vid vlan name mac address port type ---- ---------------- ----------------- ------ ---------------- 1 def...

  • Page 99

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show ipfdb command: show ipfdb interface ip address port learned ------------ --------------- ------ ------------ system 10.0.0.1 1:13 dynamic system 10.0.0.2 1:13 dynamic system 10.0.0.3 1:13 dynamic system 10.0.0.4 1:13 ...

  • Page 100

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 12 b roadcast s torm c ontrol c ommands on a computer network, packets such as multicast packets and broadcast packets continually flood the network as normal procedure. At times, this traffic may increase do to a malicious endstatio...

  • Page 101

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config traffic control latter of which will now provide shutdown, recovery and trap notification functions for the switch. Parameters − used to specify a range of ports to be configured for traffic control. This is specified by listi...

  • Page 102

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config traffic control and the port is still experiencing packet storms, the port will be placed in shutdown forever mode and can only be manually recovered using the config traffic control_recover command. Time_interval - the interv...

  • Page 103

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4# config traffic control_recover 1:1-1:5 command: config traffic control_recover 1:1-1:5 success. Des-6500:4# config traffic control_trap purpose used to configure the trap settings for the packet storm control mechanism. S...

  • Page 104

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show traffic control traffic control settings. This is specified by listing the lowest switch number and the beginning port number on that switch, separated by a colon. Then the highest switch number, and the highest port number of t...

  • Page 105: S C

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 13 q o s c ommands the xstack des-6500 supports 802.1p priority queuing. This switch has eight classes of service for each port on the switch, one of which is internal and not configurable to the user. These hardware classes of servi...

  • Page 107

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config bandwidth_control − specifies the packet limit, in mbps, that the above ports will be allowed to transmit. Restrictions only administrator-level users can issue this command. Example usage: to configure bandwidth control: des-...

  • Page 108

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show bandwidth_control 1:1-1:10 command: show bandwidth_control 1:1-1:10 bandwidth control table port rx rate (mbit/sec) tx_rate (mbit/sec) ---- ------------------------ ---------------------- 1:1 no_limit 10 1:2 no_limit ...

  • Page 109

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config scheduling combination of strict and weight-fair (weighted round-robin “ wrr ” ) scheduling. Priority classes that have a 0 in the max_packet field will forward packets with strict priority scheduling. The remaining classes, t...

  • Page 110

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show scheduling purpose used to display the currently configured traffic scheduling on the switch. Syntax show scheduling description the show scheduling command displays the current configuration for the maximum number of packets ( ...

  • Page 111

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config 802.1p user_priority 4 4 5 5 6 6 7 6 parameters − specifies which of the eight 802.1p priority tags (0 through 7) to map to one of the switch’s hardware priority classes of service ( , 0 through 6). − specifies to which of the...

  • Page 112

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config 802.1p default_priority purpose used to specify default priority settings on the switch. Untagged packets that are received by the switch will be assigned a priority tag in its priority field using this command. Syntax config ...

  • Page 113

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to display the current 802.1p default priority configuration on the switch: des-6500:4# show 802.1p default_priority command: show 802.1p default_priority port priority ------- ----------- 1:1 0 1:2 0 1:3 0 1:4 0 1:5 0...

  • Page 114

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config scheduling_mechanism parameters strict – entering the strict parameter indicates that the highest class of service is the first to be processed. That is, the highest class of service should finish emptying before the others be...

  • Page 115

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual enable hol_prevention purpose used to enable hol prevention. Syntax enable hol_prevention description the enable hol_prevention command enables head of line prevention. Parameters none. Restrictions you must have administrator privil...

  • Page 116

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show hol_prevention purpose used to show hol prevention. Syntax show hol_prevention description the show hol_prevention command displays the head of line prevention state. Parameters none. Restrictions none. Example usage: to view th...

  • Page 118

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to add the mirroring ports: des-6500:4# config mirror port 1:10 add source ports 1:1-1:5 both command: config mirror port 1:10 add source ports 1:1-1:5 both success. Des-6500:4# config mirror port delete purpose used t...

  • Page 119

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual enable mirror purpose used to enable a previously entered port mirroring configuration. Syntax enable mirror description this command, combined with the disable mirror command below, allows you to enter a port mirroring configuration...

  • Page 120

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show mirror purpose used to show the current port mirroring configuration on the switch. Syntax show mirror description this command displays the current port mirroring configuration on the switch. Parameters none. Restrictions none....

  • Page 121: Vlan C

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 15 vlan c ommands the xstack des-6500 incorporates protocol-based vlans. This standard, defined by the ieee 802.1v standard maps packets to protocol-defined vlans by examining the type octet within the packet header to discover the t...

  • Page 122

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create vlan tag − the vlan id of the vlan to be created. Allowed values = 2-4094 type – this parameter uses the type field of the packet header to determine the packet protocol and destination vlan. There are two main choices of type...

  • Page 123

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create vlan information is defined by the systems network architecture (sna) 802.2 protocol. Protocol–snaethernet2 - using this parameter will instruct the switch to forward packets to this vlan if the tag in the packet header is con...

  • Page 124

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual note: a specific protocol vlan and a user defined protocol vlan with the same encapsulation protocol cannot coexist and will result in a fail! Message. (for example, if a user creates an ethernet2 protocol vlan, the user can not crea...

  • Page 125

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config vlan add description this command allows the user to add ports to the port list of a previously configured vlan. Additional ports may be specified as tagging, untagging, or forbidden. The default is to assign the ports as unta...

  • Page 126

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config vlan delete specifies all of the ports between slot 1, port 3 and slot 2, port 4 − in numerical order. Restrictions only administrator-level users can issue this command. Example usage: to delete ports 5-7 of module 2 of the v...

  • Page 127

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#config gvrp 1:1-1:4 state enabled ingress_checking enabled acceptable_frame tagged_only pvid 2 command: config gvrp 1:1-1:4 state enabled ingress_checking enabled acceptable_frame tagged_only pvid 2 success. Des-6500:4# en...

  • Page 128

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show vlan purpose used to display the current vlan configuration on the switch. Syntax show vlan {} description this command displays summary information about each vlan including the vlan id, vlan name, the tagging/untagging status,...

  • Page 129

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show gvrp purpose used to display the gvrp status for a port list on the switch. Syntax show gvrp {} description this command displays the gvrp status for a port list on the switch. Parameters − specifies a range of ports for which t...

  • Page 130

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 16 l ink a ggregation c ommands the link aggregation commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create link_aggregation group_id {type [l...

  • Page 131

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#create link_aggregation group_id 1 command: create link_aggregation group_id 1 success. Des-6500:4# delete link_aggregation group_id purpose delete link_aggregation group_id this command is used to delete a previously conf...

  • Page 132

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual parameters group _id − specifies the group id. The switch allows up to 32 link aggregation groups to be configured. The group number identifies each of the groups. Master_port − master port id. Specifies which port (by port number) o...

  • Page 136

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show lacp_port purpose used to display current lacp port mode settings. Syntax show lacp_port {} description this command will display the lacp mode settings as they are currently configured. Parameters - specifies a range of ports t...

  • Page 137: Ip C

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 17 ip c ommands (i ncluding m ultiple ip interfaces per vlan ) multiple ip interfaces per vlan is a function that allows multiple ip interfaces to be assigned to the same vlan. This is beneficial to the administrator when the number ...

  • Page 138

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create ipif to be created. The address and mask information can be specified using the traditional format (for example, 10.1.2.3/255.0.0.0) or in cidr format, (10.1.2.3/8). − the name of the vlan that will be associated with the abov...

  • Page 139

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config ipif vlan − the name of the vlan corresponding to the previously created ip interface. If a primary and secondary ip interface are configured for the same vlan (subnet), the user cannot change the vlan of the ip interface. Sta...

  • Page 141

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show ipif purpose used to display the configuration of an ip interface on the switch. Show ipif {} this command will display the configuration of an ip interface on the switch. Parameters − the name created for the ip interface to be...

  • Page 142: Igmp C

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 18 igmp c ommands (i ncluding igmp v 3) igmp or internet group management protocol is a protocol implemented by systems utilizing ipv4 to collect the membership information needed by the multicast routing protocol through various que...

  • Page 144

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to display igmp configurations: des-6500:4#show igmp command: show igmp igmp interface configurations interface ip address/netmask ver- query maximum robust- last state sion response ness member time value query interval ------------...

  • Page 145

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show igmp group ipif system group 224.0.1.1 command: show igmp group ipif system group 224.0.1.1 interface name multicast group last reporter ip querier ip expire -------------------- ------------------- ------------------...

  • Page 148

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config igmp_snooping querier interval) + (1 x query response interval). • other querier present interval—amount of time that must pass before a multicast router decides that there is no longer another multicast router that is the que...

  • Page 149

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to enable igmp snooping on the switch: des-6500:4#enable igmp_snooping command: enable igmp_snooping success. Des-6500:4# disable igmp_snooping purpose used to enable igmp snooping on the switch. Syntax disable igmp_snooping {forward...

  • Page 150

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config router_ports number and the beginning port number on that slot, separated by a colon. Then the highest slot number, and the highest port number of the range (also separated by a colon) are specified. The beginning and end of t...

  • Page 151

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#config router_ports_forbidden default add 2:1-2:10 command: config router_ports_forbidden default add 2:1-2:10 success. Des-6500:4# show router_ports purpose used to display the currently configured router ports on the swi...

  • Page 152

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show igmp_snooping parameters − the name of the vlan for which to view the igmp snooping configuration. Restrictions none. Example usage: to show igmp snooping: des-6500:4#show igmp_snooping command: show igmp_snooping igmp snooping ...

  • Page 153

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: vlan name : default mac address : 01-00-5e-00-00-02 reports : 2 to show igmp snooping group: des-6500:4#show igmp_snooping group command: show igmp_snooping group multicast group: 224.0.0.2 reports : 1 port member : 1:...

  • Page 154

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to view the igmp snooping forwarding table for vlan “trinity”: des-6500:4#show igmp_snooping forwarding vlan trinity command: show igmp_snooping forwarding vlan trinity vlan name : trinity port member : 1:17 multicast ...

  • Page 155

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 21 a ccess a uthentication c ontrol c ommands the access authentication control commands allows secure access to the switch using the tacacs / xtacacs / tacacs+ and radius protocols. When a user logs in to the switch or tries to acce...

  • Page 156

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual note: tacacs, xtacacs and tacacs+ are separate entities and are not compatible. The switch and the server must be configured exactly the same, using the same protocol. (for example, if the switch is set up for tacacs authentication, ...

  • Page 157

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual command parameters show authen server_host config authen parameter response_timeout show authen parameter enable admin config admin local_enable config authen parameter attempt each command is listed, in detail, in the following sect...

  • Page 158

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to disable the system access authentication policy: des-6500:4#disable authen_policy command: disable authen_policy success. Des-6500:4# show authen_policy purpose used to display the system access authentication polic...

  • Page 159

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#create authen_login method_list_name trinity command: create authen_login method_list_name trinity success. Des-6500:4# config authen_login purpose used to configure a user-defined or default method list of authentication ...

  • Page 160

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config authen_login authenticated using the local user account database on the switch. None – adding this parameter will require no authentication to access the switch. Method_list_name – enter a previously implemented method list na...

  • Page 161

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#config authen_login default method xtacacs tacacs+ local command: config authen_login default method xtacacs tacacs+ local success. Des-6500:4# delete authen_login method_list_name purpose used to delete a previously confi...

  • Page 162

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show authen_login security protocols which are permanently set in the switch. Keyword refers to authentication using a technique instead of tacacs/xtacacs/tacacs+ and radius, which are local (authentication through the user account o...

  • Page 163

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#create authen_enable method_list_name permit command: show authen_login method_list_name permit success. Des-6500:4# config authen_enable purpose used to configure a user-defined method list of authentication methods for p...

  • Page 164

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config authen_enable require the user to be authenticated using a user-defined server group previously configured on the switch. Local_enable – adding this parameter will require the user to be authenticated using the local user acco...

  • Page 165

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#config authen_enable default method xtacacs tacacs+ local command: config authen_enable default method xtacacs tacacs+ local success. Des-6500:4# delete authen_enable method_list_name purpose used to delete a user-defined ...

  • Page 166

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show authen_enable refers to server groups defined by the user. Built-in group refers to the tacacs/xtacacs/tacacs+ and radius security protocols which are permanently set in the switch. Keyword refers to authentication using a techn...

  • Page 167

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config authen application telnet – choose this parameter to configure the telnet login method. Ssh - choose this parameter to configure the ssh (secure shell) login method. Http – choose this parameter to configure the web interface ...

  • Page 168

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show authen application command: show authen application application login method list enable method list ---------------- ------------------ ------------------------ console default default telnet trinity default ssh defa...

  • Page 169

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create authen server_host - specify an alphanumeric string up to 254 characters to be a key for the tacacs server. None – specify this parameter to not use any key. Timeout - enter the time in seconds the switch will wait for the ser...

  • Page 170

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config authen server_host tacacs protocol. Xtacacs - enter this parameter if the server host utilizes the xtacacs protocol. Tacacs+ - enter this parameter if the server host utilizes the tacacs+ protocol. Radius - enter this paramete...

  • Page 171

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual delete authen server_host tacacs – enter this parameter if the server host utilizes the tacacs protocol. Xtacacs - enter this parameter if the server host utilizes the xtacacs protocol. Tacacs+ - enter this parameter if the server ho...

  • Page 172

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show authen server_host command: show authen server_host ip address protocol port timeout retransmit key --------------- -------- ----- ------- --------------- -------- 10.53.13.94 tacacs 49 5 2 -------- total entries : 1 ...

  • Page 174

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual delete authen server_group purpose used to delete a user-defined authentication server group. Syntax delete authen server_group description this command will delete an authentication server group. Parameters - enter an alphanumeric s...

  • Page 175

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show authen server_group command: show authen server_group group name ip address protocol --------------- --------------- -------- radius ---------------------------------------- darren 10.53.13.2 tacacs tacacs 10.53.13.94...

  • Page 176

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config authen parameter attempt purpose used to configure the maximum number of times the switch will accept authentication attempts. Syntax config authen parameter attempt description this command will configure the maximum number o...

  • Page 177

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show authen parameter command: show authen parameter response timeout: 60 seconds user attempts : 5 des-6500:4# enable admin purpose used to promote user level privileges to administrator level privileges. Syntax enable ad...

  • Page 178

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config admin local_enable parameters - after entering this command, the user will be prompted to enter the old password, then a new password in an alphanumeric string of no more than 15 characters, and finally prompted to enter the n...

  • Page 179: Ssh

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 22 ssh c ommands the steps required to use the ssh protocol for secure communication between a remote pc (the ssh client) and the switch (the ssh server), are as follows: create a user account with admin-level access using the create...

  • Page 180

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual enable ssh purpose used to enable ssh. Syntax enable ssh description this command is used to enable ssh on the switch. Parameters none. Restrictions only administrator-level users can issue this command. Usage example: to enable ssh:...

  • Page 181

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config ssh authmode parameters password – this parameter may be chosen if the administrator wishes to use a locally configured password for authentication on the switch. Publickey - this parameter may be chosen if the administrator w...

  • Page 183

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4# show ssh server command: show ssh server ssh max session : 3 ssh server status : disabled connection timeout : 120 (sec) authenticate failed attempts : 2 rekey timeout : never listened port number : 22 des-6500:4# config ...

  • Page 184

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4# config ssh user trinity authmode password command: config ssh user trinity authmode password success. Des-6500:4# show ssh user authmode purpose used to display the ssh user setting. Syntax show ssh user authmode descript...

  • Page 185

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config ssh algorithm aes256 - this parameter will enable or disable the advanced encryption standard aes256 encryption algorithm. Arcfour - this parameter will enable or disable the arcfour encryption algorithm. Blowfish - this param...

  • Page 186

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual usage example: to display ssh algorithms currently set on the switch: des-6500:4#show ssh algorithm command: show ssh algorithm encryption algorithm 3des :enable aes128 :enable aes192 :enable aes256 :enable arc4 :enable blowfish :ena...

  • Page 187: Ssl C

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 23 ssl c ommands secure sockets layer or ssl is a security feature that will provide a secure communication path between a host and client through the use of authentication, digital signatures and encryption. These security functions...

  • Page 189

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual note: enabling the ssl function on the switch will disable the port for the web manager (port 80). To log on to the web based manager, the entry of your url must begin with https:// . (ex. Https://10.90.90.90) disable ssl purpose to ...

  • Page 190

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config ssl cachetimeout purpose used to configure the ssl cache timeout. Syntax config ssl cachetimeout timeout description this command will set the time between a new key exchange between a client and a host using the ssl function....

  • Page 191

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show ssl purpose used to view the ssl status and the certificate file status on the switch. Syntax show ssl {certificate} description this command is used to view the ssl status on the switch. Adding the certificate parameter will al...

  • Page 192

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual download certificate parameters - enter the ip address of the tftp server. Certfilename - enter the path and the filename of the certificate file to download. Keyfilename - enter the path and the filename of the key exchange file to ...

  • Page 193: 802.1X C

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 24 802.1x c ommands the xstack des-6500 implement the server-side of the ieee 802.1x port-based and mac-based network access control. This mechanism is intended to allow only authorized users, or other network devices, access to netw...

  • Page 195

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create 802.1x user purpose used to create a new 802.1x user. Create 802.1x user the create 802.1x user command is used to create new 802.1x users. − a username of up to 15 alphanumeric characters in length. Only administrator-level u...

  • Page 196

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual delete 802.1x user used to delete an 802.1x user account on the switch. Delete 802.1x user the delete 802.1x user command is used to delete the 802.1x port- based or mac-based network access control local users currently configured o...

  • Page 197

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show 802.1x auth_configuration forces the authenticator of the port to become authorized. Forceunauth forces the port to become unauthorized. Quietperiod − shows the time interval between authentication failure and the start of a new...

  • Page 199

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 1:11 forceauth success authorized 1:12 forceauth success authorized 1:13 forceauth success authorized 1:14 forceauth success authorized 1:15 forceauth success authorized 1:16 forceauth success authorized 1:17 forceauth success author...

  • Page 200

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to configure 802.1x authentication by mac address: des-6500:4#config 802.1x auth_mode mac_based command: config 802.1x auth_mode mac_based success. Des-6500:4# config 802.1x capability ports purpose used to configure the 802.1x capab...

  • Page 201

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config 802.1x auth_parameter purpose used to configure the 802.1x authentication parameters on a range of ports. The default parameter will return all ports in the specified range to their default 802.1x settings. Syntax config 802.1...

  • Page 207

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to display radius settings on the switch: des-6500:4#show radius command: show radius idx ip address auth-port acct-port status key number number ----- ------------------ --------- --------- ----------- ------------ 1 ...

  • Page 208

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show auth_client purpose used to display the current radius authentication client. Show auth_client the show auth_client command is used to display the current radius authentication client currently configured on the switch. Paramete...

  • Page 209

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show auth_diagnostics all – specifies that all ports will be viewed. Restrictions none. Example usage: to display the current authentication diagnostics for port 16: des-6500:4#show auth_diagnostics ports 1:16 command: show auth_diag...

  • Page 210

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to display the current authentication session statistics for port 16: des-6500:4#show auth_session_statistics ports 1:16 command: show auth_session_statistics ports 1:16 port number : 1:16 sessionoctetsrx 0 sessionoctetstx 0 sessionf...

  • Page 211

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show auth_statistics ports 1:16 command: show auth_statistics ports 1:16 port number : 1:16 eapolframesrx 0 eapolframestx 0 eapolstartframesrx 0 eapolreqidframestx 0 eapollogoffframesrx 0 eapolreqframestx 0 eapolrespidfram...

  • Page 212: (Acl) C

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 25 a ccess c ontrol l ist (acl) c ommands (i ncluding cpu) the xstack des-6500 implement access control lists that enable the switch to deny network access to specific devices or device groups based on ip settings, mac address, packe...

  • Page 214

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual the ip parameter instructs the switch that this new rule will be applied to the ip addresses contained within each frame’s header. Source_ip tells the switch that this rule will apply to the source ip addresses in each frame’s header...

  • Page 216

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create access_profile (for ethernet) used to create an access profile on the switch by examining the ethernet part of the packet header. Masks entered can be combined with the values the switch finds in the specified frame header fie...

  • Page 217

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config access_profile profile_id (for ethernet) purpose used to configure the ethernet access profile on the switch and to define specific values for the rules that will be used to by the switch to determine if a given packet should ...

  • Page 218

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config access_profile profile_id (for ethernet) permitted to be forwarded by the switch. Replace_dscp − allows specification of a value to be written to the dscp field of an incoming packet that meets the criteria specified in the fi...

  • Page 220

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create access_profile (ip) mask for the destination port. • protocol_id − specifies that the switch will examine each frame’s protocol id field. • user_define − enter a hexidecimal value that will identify the protocol to be discover...

  • Page 221

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config access_profile profile_id (ip) packet to see if it will be either forwarded or filtered based on one or more of the following: • vlan − specifies that the access profile will apply to only to this vlan. • source_ip − specifies...

  • Page 222

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config access_profile profile_id (ip) their header. • protocol_id − specifies that the switch will examine the protocol field in each packet and if this field contains the value entered here, apply the appropriate rules. • user_defin...

  • Page 223

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create access_profile (packet content mask) purpose used to create an access profile on the switch by examining the ethernet part of the packet header. Packet content masks entered will specify certain bytes of the packet header to b...

  • Page 224

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config access_profile profile_id (packet content mask) purpose to configure the rule for a previously created access profile command based on the packet content mask. Packet content masks entered will specify certain bytes of the pac...

  • Page 225

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config access_profile profile_id (packet content mask) specifies switch number 2, port 4. 1:3-2:4 specifies all of the ports between switch 1, port 3 and switch 2, port 4 − in numerical order. Permit – specifies that packets that mat...

  • Page 226

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create access_profile (ipv6) purpose used to create an access profile on the switch by examining the ipv6 part of the packet header. Masks can be entered that will be combined with the values the switch finds in the specified frame h...

  • Page 227

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config access_profile profile_id (ipv6) purpose used to configure the ipv6 access profile on the switch and to define specific values for the rules that will be used to by the switch to determine if a given packet should be forwarded...

  • Page 228

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config access_profile profile_id (ipv6) used to determine the cos queue to which packets are forwarded to. Once this field is specified, packets accepted by the switch that match this priority are forwarded to the cos queue specified...

  • Page 229

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4# delete access_profile profile_id 1 success. Command: delete access_profile profile_id 1 des-6500:4# show access_profile purpose used to display the currently configured access profiles on the switch. Syntax show access_pr...

  • Page 230

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 2 ====================================================================== access profile id: 3 type : packet content ====================================================================== mask option : offset 0-15 : 0xffffffff 0xfffff...

  • Page 231

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create cpu access_profile address mask. • destination_mac - specifies to examine the destination mac address mask. • ethernet_type − specifies that the switch will examine the ethernet type value in each frame’s header. Ip − specifie...

  • Page 232

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create cpu access_profile • dst_port_mask − specifies a udp port mask for the destination port. • protocol_id − specifies that the switch will examine each frame’s protocol id field. • user_define_mask − specifies that the rule appli...

  • Page 233

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to delete the cpu access profile with a profile id of 1: des-6500:4#delete cpu access_profile profile_id 1 command: delete cpu access_profile profile_id 1 success. Des-6500:4# config cpu access_profile purpose used to configure a cpu...

  • Page 234

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config cpu access_profile • vlan − specifies that the access profile will apply to only to this vlan. • vlan − specifies that the access profile will apply to only this vlan. • source_mac − specifies that the access profile will appl...

  • Page 235

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config cpu access_profile in their header. • protocol_id − specifies that the switch will examine the protocol field in each packet and if this field contains the value entered here, apply the following rules. • packet_content_mask –...

  • Page 236

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual enable cpu_interface_filtering purpose used to enable cpu interface filtering on the switch. Syntax enable cpu_interface_filtering description this command is used, in conjunction with the disable cpu_interface_filtering command belo...

  • Page 237

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show cpu_interface_filtering parameters none. Restrictions only administrator-level users can issue this command. Example usage: to show the cpu filtering state on the switch: des-6500:4#show cpu_interface_filtering command: show cpu...

  • Page 238

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 26 s afeguard e ngine c ommands periodically, malicious hosts on the network will attack the switch by utilizing packet flooding (arp storm) or other methods. These attacks may increase the cpu utilization beyond its capability. To a...

  • Page 240

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show safeguard_engine purpose to display the safeguard engine parameters currently set in the switch. Syntax show safeguard_engine description this command is used to show the safeguard engine information currently set on the switch....

  • Page 241

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 26 t raffic s egmentation c ommands traffic segmentation allows you to further sub-divide vlans into smaller groups of ports that will help to reduce traffic on the vlan. The vlan rules take precedence, and then the traffic segmentat...

  • Page 242

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show traffic_segmentation purpose used to display the current traffic segmentation configuration on the switch. Syntax show traffic_segmentation description the show traffic_segmentation command is used to display the current traffic...

  • Page 243: D-L

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 28 d-l ink s ingle ip m anagement c ommands simply put, d-link single ip management is a concept that will stack switches together over ethernet instead of using stacking ports or modules. Switches using single ip management (labeled...

  • Page 244

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 2. Cs’s must change their role to cas and then to ms, to become a ms of a sim group. Thus the cs cannot directly be converted to a ms. 3. The user can manually configure a cs to become a cas. 4. A ms can become a cas by: a. Being con...

  • Page 245

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual enable sim purpose used to enable single ip management (sim) on the switch syntax enable sim description this command will enable sim globally on the switch. Sim features and functions will not function properly unless this function ...

  • Page 246

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show sim description this command will display the current information regarding the sim group on the switch, including the following: sim version - displays the current single ip management version on the switch. Firmware version - ...

  • Page 247

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show sim command: show sim sim version : ver-1 firmware version : build 3.00-b29 device name : mac address : 00-35-26-11-11-00 capabilities : l3 platform : des-6500 l3 switch sim state : enabled role state : commander disc...

  • Page 248

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to show other groups information in summary, if group is specified: des-6500:4#show sim group command: show sim group sim group name : default id mac address platform / hold firmware device name capability time version --- ----------...

  • Page 250

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#config sim_group delete 1 command: config sim_group delete 1 please wait for ack... Success. Des-6500:4# config sim purpose used to configure role parameters for the sim protocol on the switch. Syntax config sim [{[command...

  • Page 251

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#config sim commander dp_interval 30 command: config sim commander dp_interval 30 success. Des-6500:4# to change the hold time of the discovery protocol: des-6500:4# config sim commander hold_time 120 command: config sim co...

  • Page 253

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#download sim_ms configuration 10.53.13.94 c:/dgssri.Txt members all command: download sim_ms configuration 10.53.13.94 c:/dgssri.Txt members all this device is updating configuration. Please wait... Download status : id ma...

  • Page 254: Sntp

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 29 t ime and sntp c ommands the simple network time protocol (sntp) {an adaptation of the network time protocol (ntp)} commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following t...

  • Page 255

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to configure sntp settings: des-6500:4#config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 command: config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 success. Des-6500:4# show sntp purpose show sntp this c...

  • Page 256

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#enable sntp command: enable sntp success. Des-6500:4# disable sntp purpose disables sntp server support. Syntax disable sntp description this will disable sntp support. Sntp service must be separately configured (see confi...

  • Page 257

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#config time 30jun2003 16:30:30 command: config time 30jun2003 16:30:30 success. Des-6500:4# config time zone purpose used to determine the time zone used in order to adjust the system clock. Syntax config time_zone {operat...

  • Page 258

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config dst requirement. Dst adjustment effects system time for both manually configured time and time set using sntp service. Parameters disable - disable the dst seasonal time adjustment for the switch. Repeating - using repeating m...

  • Page 261

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual delete arpentry table. Parameters − the ip address of the end node or station. All − deletes all arp entries. Only administrator-level users can issue this command. Restrictions example usage: to delete an entry of ip address 10.48.7...

  • Page 262

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show arpentry parameters ipif − enter the ip interface name for which to display arp settings. Static − displays the static entries to the arp table. Restrictions none. Example usage: to display the arp table : des-6500:4#show arpent...

  • Page 263

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to display an entry in the arp table: des-6500:4#show arpentry ipaddress 10.1.1.169 command: show arpentry ipaddress 10.1.1.169 arp aging time : 30 interface ip address mac address type ------------- --------------- -----------------...

  • Page 264: Vrrp C

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 31 vrrp c ommands vrrp or virtual routing redundancy protocol is a function on the switch that dynamically assigns responsibility for a virtual router to one of the vrrp routers on a lan. The vrrp router that controls the ip address ...

  • Page 265

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to enable vrrp globally on the switch: des-6500:4#enable vrrp command: enable vrrp success. Des-6500:4# example usage: to enable the virtual ip address to be pinged: des-6500:4#enable vrrp ping command: enable vrrp pin...

  • Page 268

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config vrrp vrid gateway that will be statically assigned to end hosts and must be set for all routers that participate in this group. Critical_ip - enter the ip address of the physical device that will provide the most direct route ...

  • Page 269

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config vrrp ipif parameters authtype – specifies the type of authentication used. The authtype must be consistent with all routers participating within the vrrp group. The user may choose between: ipif - enter the name of a previousl...

  • Page 270

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show vrrp command: show vrrp global vrrp :enabled non-owner response ping : disabled interface name : system authentication type : no authentication vrid : 2 virtual ip address : 10.53.13.3 virtual mac address : 00-00-5e-0...

  • Page 272

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual create iproute default purpose used to create ip route entries to the switch’s ip routing table. Syntax create iproute default {} description this command is used to create a default static ip route entry to the switch’s ip routing t...

  • Page 273

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual delete iproute default purpose used to delete a default ip route entry from the switch’s ip routing table. Syntax delete iproute default description this command will delete an existing default entry from the switch’s ip routing tabl...

  • Page 274

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 33 r oute r edistribution c ommands the route redistribution commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create route redistribute dst osp...

  • Page 275

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual route source metric metric type rip 0 to 16777214 mettype 1 mettype 2 static 0 to 16777214 mettype 1 mettype 2 local 0 to 16777214 mettype 1 mettype 2 allowed metric type combinations are mettype 1 or mettype 2 . The metric value 0 a...

  • Page 276

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual routing information source − ospf and the static route table. Routing information will be redistributed to rip. The following table lists the allowed values for the routing metrics and the types (or forms) of the routing information ...

  • Page 277

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config route redistribute dst ospf src • type-1 calculates the metric (for rip to ospf) by adding the destination’s interface cost to the metric entered in the metric field. • type-2 uses the metric entered in the metric field withou...

  • Page 279

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to delete route redistribution settings: des-6500:4#delete route redistribute dst rip src ospf command: delete route redistribute dst rip src ospf success. Des-6500:4# show route redistribute purpose used to display th...

  • Page 281

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config dhcp_relay add ipif purpose used to add an ip destination address to the switch's dhcp/bootp relay table. Syntax config dhcp_relay add ipif description this command adds an ip address as a destination to which to forward (rela...

  • Page 283

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to configure dhcp relay option 82 check: des-6500:4#config dhcp_relay option_82 check enable command: config dhcp_relay option_82 check enable success. Des-6500:4# config dhcp_relay option_82 policy purpose used to con...

  • Page 284

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to show the dhcp relay configuration: des-6500:4#show dhcp_relay command: show dhcp_relay dhcp/bootp hops count limit : 2 system 10.58.44.6 dhcp/bootp relay status : enabled dhcp/bootp relay time threshold : 23 dhcp relay agent infor...

  • Page 285

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual disable dhcp_relay used to disable the dhcp/bootp relay function on the switch. Syntax disable dhcp_relay description this command is used to disable the dhcp/bootp relay function on the switch. Parameters none. Restrictions only adm...

  • Page 287

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#config dnsr add static dns1 10.43.21.12 command: config dnsr add static dns1 10.43.21.12 success. Des-6500:4# example usage: to delete an entry domain name dns1, ip address 10.43.21.12 from dns static table. Des-6500:4#con...

  • Page 288

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#enable dnsr cache command: enable dnsr cache success. Des-6500:4# example usage: to enable static table lookup for dns relay. Des-6500:4#enable dnsr static command: enable dnsr static success. Des-6500:4# disable dnsr purp...

  • Page 289

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#disable dnsr cache command: disable dnsr cache success. Des-6500:4# example usage: to disable static table lookup for dns relay. Des-6500:4#disable dnsr static command: disable dnsr static success. Des-6500:4# show dnsr pu...

  • Page 292

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to disable rip: des-6500:4#disable rip command: disable rip success. Des-6500:4# show rip purpose used to display the rip configuration and statistics for the switch. Syntax show rip {ipif } description this command will display the ...

  • Page 295

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: command: disable dvmrp to disable dvmrp: des-6500:4#disable dvmrp success. Des-6500:4# show dvmrp routing_table used to display the current dvmrp routing table. Syntax show dvmrp routing table [ipaddress ] description ...

  • Page 296

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show dvmrp neighbor parameters − the name of the ip interface for which to display the dvmrp neighbor table. Ipaddress − the ip address and netmask of the destination. The address and mask information can be specified using the tradi...

  • Page 297

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show dvmrp nexthop command: show dvmrp nexthop source ip address/netmask interface name type ----------------- --------------- ------ 10.0.0.0/8 ip2 leaf 10.0.0.0/8 ip3 leaf 20.0.0.0/8 system leaf 20.0.0.0/8 ip3 leaf 30.0....

  • Page 299

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#config pim ipif system hello 35 jp_interval 70 state enabled command: config pim ipif system hello 35 jp_interval 70 state enabled success. Des-6500:4# enable pim purpose used to enable pim function on the switch. Syntax e...

  • Page 301

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to display pim settings as configured on the switch: des-6500:4#show pim command: show pim pim global state : disabled pim-dm interface table hello join/prune interface ip address interval interval state ------------ --------------- ...

  • Page 302: Ip M

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 39 ip m ulticasting c ommands the ip multicasting commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters show ipmc cache {group } {ipaddress } show i...

  • Page 304: Md5 C

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 40 md5 c onfiguration c ommands the md5 configuration commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create md5 key config md5 key delete md5...

  • Page 305

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#config md5 key 1 taboo command: config md5 key 1 taboo success. Des-6500:4# delete md5 key purpose used to delete an entry in the md5 key table. Syntax delete md5 key description this command is used to delete a specific e...

  • Page 306: Ospf C

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 41 ospf c onfiguration c ommands the ospf configuration commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config ospf router_id enable ospf disa...

  • Page 308

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#enable ospf command: enable ospf success. Des-6500:4# disable ospf purpose used to disable ospf on the switch. Syntax disable ospf description this command, in combination with the enable ospf command above, is used to ena...

  • Page 309

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to show ospf state: des-6500:4#show ospf command: show ospf --------------- ------ ----------------------- ----------------- 10.1.1.1 normal none none total entries : 4 ----------- --------------- -------- -------- -------------- ---...

  • Page 315

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#delete ospf aggregation 10.1.1.1 10.48.76.122/16 lsdb_type summary command: delete ospf aggregation 10.1.1.1 10.48.76..122/16 lsdb_type summary success. Des-6500:4# config ospf aggregation purpose used to configure the osp...

  • Page 316

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual usage example command: show ospf aggregation des-6500:4# to display ospf area aggregation settings: des-6500:4#show ospf aggregation ospf area aggregation settings area id aggregated lsdb advertise network address type ------------ -...

  • Page 317

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show ospf lsdb command: show ospf lsdb area lsdb advertising link state cost sequence id type router id id number ----------- -------------- ------------------ ------------------ ------- ----------------- 0.0.0.0 rtrlink 5...

  • Page 318

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual show ospf virtual_neighbor parameters − a 32-bit number in the form of an ip address (xxx.Xxx.Xxx.Xxx) that uniquely identifies the ospf area in the ospf domain. − the ospf router id for the neighbor. This is a 32-bit number in the f...

  • Page 319

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config ospf ipif metric − the interface metric (1 to 65535). Entering a 0 will allow automatic calculation of the metric. Authentication – enter the type of authentication preferred. The user may choose between: metric − this field a...

  • Page 320

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config ospf all interval between the transmission of ospf hello packets, in seconds. Between 1 and 65535 seconds can be specified. The hello interval, dead interval, authorization type, and authorization key should be the same for al...

  • Page 321

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual to display the current ospf interface settings, for a specific ospf interface: des-6500:4#show ospf ipif ipif2 command: show ospf ipif ipif2 interface name: ipif2 ip address: 123.234.12.34/24 ((link up) network medium type: broadcast...

  • Page 324

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual delete ospf virtual_link purpose used to delete an ospf virtual interface. Syntax delete ospf virtual_link description this command will delete an ospf virtual interface from the switch. Parameters − a 32-bit number in the form of an...

  • Page 325

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual des-6500:4#show ospf virtual_link command: show ospf virtual_link virtual interface configuration transit virtual hello dead authentication link area id neighbor router interval interval status --------------- ---------------------- ...

  • Page 326

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 43 j umbo f rame c ommands certain switches can support jumbo frames (frames larger than the standard ethernet frame size of 1518 bytes). To transmit frames of up to 9216 bytes (and 9220 bytes tagged), the user can increase the maxim...

  • Page 327

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual example usage: to enable the jumbo frame function on the switch: des-6500:4#disable jumbo_frame command: disable jumbo_frame success. Des-6500:4# show jumbo_frame purpose used to show the status of the jumbo frame function on the swi...

  • Page 328

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 45 c ommand h istory l ist the command history list commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters ? {} show command_history config command_h...

  • Page 330

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual config command_history purpose used to configure the command history. Syntax config command_history description this command is used to configure the command history. Parameters − the number of previously executed commands maintained...

  • Page 331

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual a t echnical s pecifications physical and environmental ac inputs & external redundant power supply 100 - 240 vac, 50/60 hz (internal universal power supply) power consumption 296w des-6504: 30w maximum des-6505: 20w maximum des-6508...

  • Page 332

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual performance transmission method store-and-forward-l3 routing ram buffer 256 mb per linecard, 256mb on cpu card. Filtering address table 16 k mac addresses per device 3k ip addresses per device packet filtering/ forwarding rate full-w...

  • Page 333

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual general standard ieee 802.3u 100base-tx fast ethernet ieee 802.3ab 1000base-t gigabit ethernet ieee 802.1d spanning tree ieee 802.1w rapid spanning tree ieee 802.1s multiple spanning tree ieee 802.1 p/q vlan ieee 802.1p priority queu...

  • Page 334

    Xstack des-6500 modular layer 3 chassis ethernet switch cli manual 331.