1. DL manuals
  2. D-Link
  3. Switch
  4. xStack DES-3526DC
  5. Cli Manual

D-Link xStack DES-3526DC Cli Manual

Other manuals for xStack DES-3526DC: User Manual, Manual, User Manual
Manual is about: DES-3500 Series Layer 2 Managed Stackable Fast Ethernet Switch

Summary of xStack DES-3526DC

  • Page 1

    ©copyright 2005. All rights reserved cli manual product model : xstack tm des-3526/des-3526dc layer 2 managed stackable fast ethernet switch release 3.60

  • Page 2

    Table of contents introduction ......................................................................................................................... 1 using the console cli ........................................................................................................ 4 command syntax ....

  • Page 3

    Igmp snooping commands ............................................................................................. 118 dhcp relay.......................................................................................................................... 128 802.1x commands .............................

  • Page 4: Introduction

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 1 1 introduction the switch can be managed through the switch’s serial port, telnet, or the web-based management agent. The command line interface (cli) can be used to configure and manage the switch via the serial port or telne...

  • Page 5

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 2 setting the switch’s ip address each switch must be assigned its own ip address, which is used for communication with an snmp network manager or other tcp/ip application (for example bootp, tftp). The switch’s default ip addre...

  • Page 6

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 3 figure 1-3. Assigning an ip address in the above example, the switch was assigned an ip address of 10.41.44.254 with a subnet mask of 255.0.0.0. The system message success indicates that the command was executed successfully. ...

  • Page 7: Using The Console Cli

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 4 2 using the console cli the des-3526 supports a console management interface that allows the user to connect to the switch’s management agent via a serial port and a terminal or a computer running a terminal emulation program....

  • Page 8

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 5 figure 2-1. Initial console screen after logging in commands are entered at the command prompt, des-3526:4# . There are a number of helpful features included in the cli. Entering the ? Command will display a list of all of the...

  • Page 9

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 6 figure 2-3. Example command parameter help in this case, the command config account was entered with the parameter . The cli will then prompt you to enter the with the message, next possible completions: . Every command in the...

  • Page 10

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 7 figure 2-5. The next available commands prompt the top-level commands consist of commands such as show or config . Most of these commands require one or more parameters to narrow the top-level command. This is equivalent to sh...

  • Page 11: Command Syntax

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 8 3 command syntax the following symbols are used to describe how command entries are made and values and arguments are specified in this manual. The online help contained in the cli and available through the console interface u...

  • Page 12

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 9 {braces} the effect of the system reset is dependent on which, if any, value is specified. Therefore, with this example there are three possible outcomes of performing a system reset. See the following chapter, basic commands ...

  • Page 14

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 11 des-3526:4#create account admin dlink command: create account admin dlink enter a case-sensitive new password:**** enter the new password again for confirmation:**** success. Des-3526:4# config account purpose used to configu...

  • Page 15

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 12 des-3526:4#show account command: show account current accounts: username access level --------------- ------------ dlink admin total entries: 1 des-3526:4# delete account purpose used to delete an existing user account. Synta...

  • Page 16

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 13 show switch purpose used to display general information about the switch. Syntax show switch description this command displays information about the switch. Parameters none. Restrictions only administrator-level users can iss...

  • Page 17

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 14 des-3526:4#show serial_port command: show serial_port baud rate : 9600 data bits : 8 parity bits : none stop bits : 1 auto-logout : 10 mins des-3526:4# config serial_port purpose used to configure the serial port. Syntax conf...

  • Page 18

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 15 enable clipaging purpose used to pause the scrolling of the console screen when the show command displays more than one page. Syntax enable clipaging description this command is used when issuing the show command which causes...

  • Page 19

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 16 enable telnet parameters − the tcp port number. Tcp ports are numbered between 1 and 65535. The “well-known” tcp port for the telnet protocol is 23. Restrictions only administrator-level users can issue this command. Example ...

  • Page 20

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 17 des-3526:4#enable web 80 command: enable web 80 success. Des-3526:4# disable web purpose used to disable the http-based management software on the switch. Syntax disable web description this command disables the web-based man...

  • Page 21

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 18 reboot purpose used to restart the switch. Syntax reboot description this command is used to restart the switch. Parameters none. Restrictions none. Example usage: to restart the switch: des-3526:4#reboot command: reboot are ...

  • Page 22

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 19 login purpose used to log in a user to the switch’s console. Syntax login description this command is used to initiate the login procedure. The user will be prompted for a username and password. Parameters none. Restrictions ...

  • Page 24

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 21 show ports purpose used to display the current configuration of a range of ports. Syntax show ports [] {description} description this command is used to display the current configuration of a range of ports. Parameters − spec...

  • Page 25

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 22 example usage: to display the configuration of all ports on a standalone switch, with description: des-3526:4#show ports description command: show ports description port port settings connection address state speed/duplex/flo...

  • Page 27

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 24 delete port_security_entry purpose used to delete a port security entry by mac address, port number and vlan id. Syntax delete port_security_entry vlan name mac_address port description this command is used to delete a single...

  • Page 28

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 25 show port_security purpose used to display the current port security configuration. Syntax show port_security {ports } description this command is used to display port security information of the switch’s ports. The informati...

  • Page 29

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 26 7 network management (snmp) commands the network management commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. The des-3526 supports the simple network mana...

  • Page 32

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 29 example usage: to create an snmp user on the switch: des-3526:4#create snmp user dlink default encrypted by_password auth md5 canadian priv none command: create snmp user dlink default encrypted by_password auth md5 canadian ...

  • Page 34

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 31 des-3526:4#delete snmp view dlinkview all command: delete snmp view dlinkview all success. Des-3526:4# show snmp view purpose used to display an snmp view previously created on the switch. Syntax show snmp view {} description...

  • Page 35

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 32 create snmp community description the create snmp community command is used to create an snmp community string and to assign access-limiting characteristics to this community string. Parameters − an alphanumeric string of up ...

  • Page 36

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 33 show snmp community purpose used to display snmp community strings configured on the switch. Syntax show snmp community {} description the show snmp community command is used to display snmp community strings that are configu...

  • Page 37

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 34 show snmp engineid purpose used to display the identification of the snmp engine on the switch. Syntax show snmp engineid description the show snmp engineid command displays the identification of the snmp engine on the switch...

  • Page 38

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 35 create snmp group remote snmp manager. Auth_priv − specifies that authorization will be required, and that packets sent between the switch and a remote snmp manger will be encrypted. Read_view – specifies that the snmp group ...

  • Page 39

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 36 show snmp groups purpose used to display the group-names of snmp groups currently configured on the switch. The security model, level, and status of each group are also displayed. Syntax show snmp groups description the show ...

  • Page 41

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 38 delete snmp host purpose used to remove a recipient of snmp traps generated by the switch’s snmp agent. Syntax delete snmp host description the delete snmp host command deletes a recipient of snmp traps generated by the switc...

  • Page 42

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 39 create trusted_host purpose used to create the trusted host. Syntax create trusted_host description the create trusted_host command creates the trusted host. The switch allows you to specify up to four ip addresses that are a...

  • Page 43

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 40 delete trusted_host purpose used to delete a trusted host entry made using the create trusted_host command above. Syntax delete trusted _host description this command is used to delete a trusted host entry made using the crea...

  • Page 44

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 41 des-3526:4#enable snmp authenticate_traps command: enable snmp authenticate_traps success. Des-3526:4# show snmp traps purpose used to show snmp trap support on the switch . Syntax show snmp traps description this command is ...

  • Page 45

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 42 disable snmp authenticate_traps purpose used to disable snmp authentication trap support. Syntax disable snmp authenticate_traps description this command is used to disable snmp authentication support on the switch. Parameter...

  • Page 46

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 43 example usage: to configure the switch location for “ h q 5 f ”: des-3526:4#config snmp system_location hq 5f command: config snmp system_location hq 5f success. Des-3526:4# config snmp system_name purpose used to configure t...

  • Page 47

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 44 disable rmon purpose used to disable rmon on the switch. Syntax disable rmon description this command is used, in conjunction with the enable rmon command above, to enable and disable remote monitoring (rmon) on the switch. P...

  • Page 49

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 46 des-3526:4#download configuration 10.48.74.121 c:\cfg\setting.Txt command: download configuration 10.48.74.121 c:\cfg\setting.Txt connecting to server................... Done. Download configuration................. Done. Des...

  • Page 50

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 47 to configure firmware section 1 as a boot up section: des-3526:4# config firmware section_id 1 boot_up command: config firmware section_id 1 boot_up success. Des-3526:4# show firmware information purpose used to display the f...

  • Page 51

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 48 show config 1. Basic (serial port, telnet and web management status) 2. Storm control 3. Ip group management 4. Syslog 5. Qos 6. Port mirroring 7. Traffic segmentation 8. Port 9. Port lock 10. 8021x 11. Snmpv3 12. Management ...

  • Page 53

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 50 example usage: to enable autoconfiguration on the switch: des-3526:4#enable autoconfig command: enable autoconfig success. Des-3526:4# when autoconfig is enabled and the switch is rebooted, the normal login screen will appear...

  • Page 54

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 51 disable autoconfig purpose use this to deactivate autoconfiguration from dhcp. Syntax disable autoconfig description this instructs the switch not to accept autoconfiguration instruction from the dhcp server. This does not ch...

  • Page 55

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 52 ping purpose used to test the connectivity between network devices. Syntax ping {times } {timeout } description the ping command sends internet control message protocol (icmp) echo messages to a remote ip address. The remote ...

  • Page 56: Network Monitoring Commands

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 53 9 network monitoring commands the network monitoring commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters show packet ports show error port...

  • Page 57

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 54 des-3526:4#show packet port 2 command: show packet port 2 port number : 2 frame size frame counts frame/sec frame type total total/sec ------------ ------------ ---------- ---------- ------- --------- 64 3275 10 rx bytes 4089...

  • Page 59

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 56 clear counters purpose used to clear the switch’s statistics counters. Syntax clear counters {ports } description this command will clear the counters used by the switch to compile statistics. Parameters − specifies a port or...

  • Page 60

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 57 des-3526:4#show log index 5 command: show log index 5 index time log text ----- ------------------- ---------------------------------------------------- 5 00000 days 00:01:09 successful login through console (username: anonym...

  • Page 61

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 58 show syslog purpose used to display the syslog protocol status as enabled or disabled. Syntax show syslog description the show syslog command displays the syslog status as enabled or disabled. Parameters none. Restrictions no...

  • Page 63

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 60 numerical facility code 0 kernel messages 1 user-level messages 2 mail system 3 system daemons 4 security/authorization messages 5 messages generated internally by syslog 6 line printer subsystem 7 network news subsystem 8 uu...

  • Page 64

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 61 des-3526:4#create syslog host 1 severity all facility local0 command: create syslog host 1 severity all facility local0 success. Des-3526:4# config syslog host purpose used to configure the syslog protocol to send system log ...

  • Page 65

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 62 numerical facility code parameters 0 kernel messages 1 user-level messages 2 mail system 3 system daemons 4 security/authorization messages 5 messages generated internally by syslog 6 line printer subsystem 7 network news sub...

  • Page 66

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 63 des-3526:4#config syslog host 1 severity all facility local0 command: config syslog host all severity all facility local0 success. Des-3526:4# example usage: to configure a syslog host for all hosts: des-3526:4#config syslog ...

  • Page 67

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 64 des-3526:4#show syslog host command: show syslog host syslog global state: disabled host id host ip address severity facility udp port status ------- --------------- -------------- -------- -------- -------- 1 10.1.1.2 all lo...

  • Page 68

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 65 des-3526:4#config system_severity trap critical command: config system_severity trap critical success. Des-3526:4#.

  • Page 69

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 66 10 multiple spanning tree protocol (mstp) commands this switch supports three versions of the spanning tree protocol; 802.1d stp, 802.1w rapid stp and 802.1s mstp. Multiple spanning tree protocol, or mstp, is a standard defin...

  • Page 70

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 67 command parameters show stp ports {} show stp instance {} show stp mst_config id each command is listed, in detail, in the following sections. Enable stp purpose used to globally enable stp on the switch. Syntax enable stp de...

  • Page 72

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 69 config stp between 1 and 10 seconds may be chosen, with a default setting of 2 seconds. Forwarddelay − the maximum amount of time (in seconds) that the root device will wait before changing states. The user may choose a time ...

  • Page 74

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 71 example usage: to configure stp with path cost 19, hellotime set to 5 seconds, migration enable, and state enable for ports 1-5 of module 1. Des-3526:4#config stp ports 1-5 externalcost 19 hellotime 5 migrate yes state enable...

  • Page 75

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 72 config stp instance_id remove_vlan - along with the vid_range parameter, this command will remove vids to the previously configured stp instance_id. - specify the vid range from configured vlans set on the switch. Supported v...

  • Page 76

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 73 config stp priority purpose used to update the stp instance configuration syntax config stp priority instance_id description this command is used to update the stp instance configuration settings on the switch. The mstp will ...

  • Page 77

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 74 des-3526:4#config stp mst_config_id revision_level 10 name trinity command : config stp mst_config_id revision_level 10 name trinity success. Des-3526:4# config stp mst_ports purpose used to update the port configuration for ...

  • Page 78

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 75 show stp purpose used to display the switch’s current stp configuration. Syntax show stp description this command displays the switch’s current stp configuration. Parameters none restrictions none. Example usage: to display t...

  • Page 79

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 76 show stp ports purpose used to display the switch’s current stp ports configuration. Syntax show stp ports description this command displays the stp ports settings for a specified port or group of ports (one port at a time). ...

  • Page 80

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 77 des-3526:4#show stp instance 0 command: show stp instance 0 stp instance settings --------------------------- instance type : cist instance status : enabled instance priority : 32768(bridge priority : 32768, sys id ext : 0 ) ...

  • Page 81: Forwarding Database Commands

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 78 11 forwarding database commands the layer 2 forwarding database commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create fdb port create...

  • Page 82

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 79 create multicast_fdb purpose used to create a static entry to the multicast mac address forwarding table (database) syntax create multicast_fdb description this command will make an entry into the switch’s multicast mac addre...

  • Page 83

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 80 config fdb aging_time purpose used to set the aging time of the forwarding database. Syntax config fdb aging_time description the aging time affects the learning process of the switch. Dynamic forwarding table entries, which ...

  • Page 84

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 81 to delete a multicast fdb entry: des-3526:4#delete fdb default 01-00-00-00-01-02 command: delete fdb default 01-00-00-00-01-02 success. Des-3526:4# clear fdb purpose used to clear the switch’s forwarding database of all dynam...

  • Page 85

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 82 des-3526:4#show multicast_fdb vlan default command: show multicast_fdb vlan default vlan name : default mac address : 01-00-5e-00-00-00 egress ports : 1-5 mode : static total entries : 1 des-3526:4# show fdb purpose used to d...

  • Page 87

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 84 des-3526:4#show multicast port_filtering_mode command: show multicast port_filtering_mode port multicast filter mode ------ --------------------------- 1 forward_unregistered_groups 2 forward_unregistered_groups 3 forward_unr...

  • Page 88

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 85 12 broadcast storm control commands the broadcast storm control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config traffic control...

  • Page 89

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 86 show traffic control purpose used to display current traffic control settings. Syntax show traffic control {group_list } description this command displays the current storm traffic control configuration on the switch. Paramet...

  • Page 90: Qos Commands

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 87 13 qos commands the des-3526 switch supports 802.1p priority queuing. The switch has 4 priority queues. These priority queues are numbered from 3 (class 3) — the highest priority queue — to 0 (class 0) — the lowest priority q...

  • Page 91

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 88 config bandwidth_control tx_rate − specifies that one of the parameters below ( no_limit or ) will be applied to the rate at which the above specified ports will be allowed to transmit packets. No_limit − specifies that there...

  • Page 93

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 90 example usage: to configure the traffic scheduling mechanism for each queue: des-3526:4# config scheduling 0 max_packet 100 max_latency 150 command: config scheduling 0 max_packet 100 max_latency 150 success. Des-3526:4# show...

  • Page 94

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 91 config 802.1p user_priority 6 3 highest 7 3 highest. This mapping scheme is based upon recommendations contained in ieee 802.1d. You can change this mapping by specifying the 802.1p user priority you want to go to the (the nu...

  • Page 95

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 92 config 802.1p default_priority purpose used to configure the 802.1p default priority settings on the switch. If an untagged packet is received by the switch, the priority configured with this command will be written to the pa...

  • Page 96

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 93 10 0 11 0 12 0 13 0 14 0 15 0 16 0 17 0 18 0 19 0 20 0 21 0 22 0 23 0 24 0 des-3526:4#.

  • Page 98

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 95 des-3526:4# config mirror port 1 add source ports 2-7 both command: config mirror port 1 add source ports 2-7 both success. Des-3526:4# example usage: to delete the mirroring ports: des-3526:4#config mirror port 1 delete sour...

  • Page 99

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 96 des-3526:4#disable mirror command: disable mirror success. Des-3526:4# show mirror purpose used to show the current port mirroring configuration on the switch. Syntax show mirror description this command displays the current ...

  • Page 101

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 98 delete vlan purpose used to delete a previously configured vlan on the switch. Syntax delete vlan description this command will delete a previously configured vlan on the switch. Parameters − the vlan name of the vlan to dele...

  • Page 103

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 100 example usage: to enable the generic vlan registration protocol (gvrp): des-3526:4#enable gvrp command: enable gvrp success. Des-3526:4# disable gvrp purpose used to disable gvrp on the switch. Syntax disable gvrp descriptio...

  • Page 104

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 101 des-3526:4#show vlan command: show vlan vid : 1 vlan name : default vlan type : static advertisement : enabled member ports : 1,5-26 static ports : 1,5-26 current untagged ports : 1,5-26 static untagged ports : 1,5-26 forbid...

  • Page 105: Asymmetric Vlan Commands

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 102 16 asymmetric vlan commands the asymmetric vlan commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enable asymmetric_vlan disable asymme...

  • Page 106

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 103 show asymmetric_vlan purpose used to view the asymmetric vlan state on the switch. Syntax show asymmetric_vlan description this command displays the asymmetric vlan state on the switch parameters none. Restrictions only admi...

  • Page 107: Link Aggregation Commands

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 104 17 link aggregation commands the link aggregation commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create link_aggregation group_id {t...

  • Page 108

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 105 delete link_aggregation group_id purpose used to delete a previously configured link aggregation group. Syntax delete link_aggregation group_id description this command is used to delete a previously configured link aggregat...

  • Page 110

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 107 des-3526:4#show link_aggregation command: show link_aggregation link aggregation algorithm = mac-source-dest group id : 1 master port : 1 member port : 5-10 active port : status : disabled flooding port : 5 des-3526:4# confi...

  • Page 111

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 108 show lacp_port purpose used to display current lacp port mode settings. Syntax show lacp_port {} description this command will display the lacp mode settings as they are currently configured. Parameters - specifies a port or...

  • Page 112: Ip-Mac Binding

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 109 18 ip-mac binding the ip-mac binding commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create address_binding ip_mac ipaddress mac_addr...

  • Page 116: Limited Ip Multicast Address

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 113 19 limited ip multicast address the limited ip multicast range window allows the user to specify which multicast address(es) reports are to be received on specified ports on the switch. This function will therefore limit the...

  • Page 119

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 116 show ipif purpose used to display the configuration of an ip interface on the switch. Syntax show ipif description this command will display the configuration of an ip interface on the switch. Parameters − the name created f...

  • Page 120

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 117 des-3526:4#enable autoconfig command: enable autoconfig success. Des-3526:4# note: more detailed information for this command and related commands can be found in the section titled switch utility commands..

  • Page 122

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 119 config igmp_snooping leave_timer − specifies the amount of time a multicast address will stay in the database before it is deleted, after it has sent out a leave group message. An entry of zero (0) specifies an immediate del...

  • Page 124

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 121 example usage: to enable igmp snooping on the switch: des-3526:4#enable igmp_snooping command: enable igmp_snooping success. Des-3526:4# disable igmp_snooping purpose used to enable igmp snooping on the switch. Syntax disabl...

  • Page 125

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 122 example usage: to show igmp snooping: des-3526:4#show igmp_snooping command: show igmp_snooping igmp snooping global state : disabled multicast router only : disabled vlan name : default query interval : 125 max response tim...

  • Page 126

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 123 des-3526:4#show igmp_snooping group command: show igmp_snooping group vlan name : default multicast group: 224.0.0.2 mac address : 01-00-5e-00-00-02 reports : 1 port member : 2,5 vlan name : default multicast group: 224.0.0....

  • Page 127

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 124 des-3526:4#show router_ports command: show router_ports vlan name : default static router port : 1-2,10 dynamic router port : total entries: 1 des-3526:4# show igmp_snooping forwarding purpose used to display the igmp snoopi...

  • Page 128

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 125 des-3526:4#show igmp_snooping group command: show igmp_snooping group vlan name : default multicast group : 224.0.0.2 mac address : 01-00-5e-00-00-02 reports : 1 port member : 2,4 vlan name : default multicast group : 224.0....

  • Page 129

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 126 create igmp_snooping multicast_vlan purpose used to create a multicast vlan on the switch. Syntax create igmp_snooping multicast_vlan 2-4094> description this command will create a multicast vlan on the switch. Parameters − ...

  • Page 130

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 127 des-3526:4# config igmp_snooping multicast_vlan trinity member_port 1,3 source_port 2 state enable command: config igmp_snooping multicast_vlan trinity member_port 1,3 source_port 2 state enable success. Des-3526:4# delete i...

  • Page 132

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 129 example usage: to add an ip destination to the dhcp relay table: des-3526:4#config dhcp_relay add ipif system 10.58.44.6 command: config dhcp_relay add ipif system 10.58.44.6 success. Des-3526:4# config dhcp_relay delete ipi...

  • Page 134

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 131 des-3526:4#config dhcp_relay option_82 check enable command: config dhcp_relay option_82 check enable success. Des-3526:4# config dhcp_relay option_82 policy purpose used to configure the reforwarding policy of relay agent i...

  • Page 135

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 132 des-3526:4#show dhcp_relay command: show dhcp_relay dhcp/bootp relay status : enabled dhcp/bootp hops count limit : 2 dhcp/bootp relay time threshold : 23 dhcp relay agent information option 82 state : enabled dhcp relay age...

  • Page 136

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 133 example usage: to disable dhcp relay: des-3526:4#disable dhcp_relay command: disable dhcp_relay success. Des-3526:4#.

  • Page 137: 802.1X Commands

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 134 23 802.1x commands the des-3526 implements the server-side of the ieee 802.1x port-based and mac-based network access control. This mechanism is intended to allow only authorized users, or other network devices, access to ne...

  • Page 138

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 135 des-3526:4#enable 802.1x command: enable 802.1x success. Des-3526:4# disable 802.1x purpose used to disable the 802.1x server on the switch. Syntax disable 802.1x description the disable 802.1x command is used to disable the...

  • Page 139

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 136 show 802.1x auth_configuration and transmitting directions, or just the receiving direction. Port control: forceauth / forceunauth / auto − shows the administrative control over the port’s authorization status. Forceauth for...

  • Page 140

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 137 show 802.1x auth_state purpose used to display the current authentication state of the 802.1x server on the switch. Syntax show 802.1x auth_state {ports } description the show 802.1x auth_state command is used to display the...

  • Page 141

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 138 des-3526:4#show 802.1x auth_state command: show 802.1x auth_state port number : 1:1 index mac address auth pae state backend state port status ------ ------------------- ----------------------- --------------------- --------...

  • Page 142

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 139 config 802.1x capability ports all − specifies all of the ports on the switch. Authenticator − a user must pass the authentication process to gain access to the network. None − the port is not controlled by the 802.1x functi...

  • Page 143

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 140 config 802.1x auth_parameter request/identity packets. Server_timeout - configure the length of time to wait for a response from a radius server. Max_req − configures the number of times to retry sending packets to a supplic...

  • Page 144

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 141 config 802.1x init then be specified. Mac_based − this instructs the switch to initialize 802.1x functions based only on the mac address. Mac addresses approved for initialization can then be specified. Ports − specifies a p...

  • Page 147

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 144 des-3526:4#show radius command: show radius index ip address auth-port acct-port status key number number ----- ------------------ --------- --------- ----------- ------------ 1 10.1.1.1 1812 1813 active switch 2 20.1.1.1 18...

  • Page 148

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 145 24 access control list (acl) commands the des-3526 implements access control lists that enable the switch to deny network access to specific devices or device groups based on ip settings or mac address. Note: the acl command...

  • Page 149

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 146 the profile_id establishes a priority within the list of profiles. A lower profile_id gives the rule a higher priority. In case of a conflict in the rules entered for different profiles, the rule with the highest priority (l...

  • Page 150

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 147 create access_profile purpose used to create an access profile on the switch and to define which parts of each incoming frame’s header the switch will examine. Masks can be entered that will be combined with the values the s...

  • Page 151

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 148 create access_profile parameters ip − specifies that the switch will examine the ip address in each frame’s header. • vlan − specifies a vlan mask. • source_ip_mask − specifies an ip address mask for the source ip address. •...

  • Page 152

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 149 des-3526:4#create access_profile ip vlan source_ip_mask 20.0.0.0 destination_ip_mask 10.0.0.0 dscp icmp type code permit profile_id 101 command: create access_profile ip vlan source_ip_mask 20.0.0.0 destination_ip_mask 10.0....

  • Page 153

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 150 config access_profile purpose used to configure an access profile on the switch and to define specific values that will be used to by the switch to determine if a given packet should be forwarded or filtered. Masks entered u...

  • Page 154

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 151 config access_profile parameters ip − specifies that the switch will look into the ip fields in each packet. • vlan − specifies that the access profile will apply to only this vlan. • source_ip − specifies that the access pr...

  • Page 155

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 152 config access_profile parameters packet_content_mask – specifies that the switch will mask the packet header beginning with the offset value specified as follows: • offset_0-15 - enter a value in hex form to mask the packet ...

  • Page 156

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 153 example usage: to display all of the currently configured access profiles on the switch: des-3526:4#show access_profile command: show access_profile access profile table access profile id : 4 type : ip frame filter ports : a...

  • Page 157

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 154 25 traffic segmentation commands traffic segmentation allows you to further sub-divide vlans into smaller groups of ports that will help to reduce traffic on the vlan. The vlan rules take precedence, and then the traffic seg...

  • Page 158

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 155 example usage: to display the current traffic segmentation configuration on the switch. Des-3526:4#show traffic_segmentation command: show traffic_segmentation traffic segmentation table port forward portlist ---- ----------...

  • Page 159: Time and Sntp Commands

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 156 26 time and sntp commands the simple network time protocol (sntp) (an adaptation of the network time protocol (npt)) commands in the command line interface (cli) are listed (along with the appropriate parameters) in the foll...

  • Page 160

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 157 to configure sntp settings: des-3526:4#config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 command: config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 success. Des-3526:4# show sntp purpose used to...

  • Page 161

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 158 disable sntp purpose to disable sntp server support. Syntax disable sntp description this will disable sntp support. Sntp service must be separately configured (see config sntp ). Parameters none. Restrictions only administr...

  • Page 163

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 160 config dst parameters disable - disable the dst seasonal time adjustment for the switch. Repeating - using repeating mode will enable dst seasonal time adjustment. Repeating mode requires that the dst beginning and ending da...

  • Page 164

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 161 des-3526:4#config dst repeating s_week 2 s_day tue s_mth 4 s_time 15:00 e_week 2 e_day wed e_mth 10 e_time 15:30 offset 30 command: config dst repeating s_week 2 s_day tue s_mth 4 s_time 15:00 e_week 2 e_day wed e_mth 10 e_t...

  • Page 166

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 163 example usage: to configure a static arp entry for the ip address 10.48.74.12 and mac address 00:50:ba:00:07:36: des-3526:4#config arpentry 10.48.74.12 00-50-ba-00-07-36 command: config arpentry 10.48.74.12 00-50-ba-00-07-36...

  • Page 168

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 165 clear arptable purpose used to remove all dynamic arp table entries. Syntax clear arptable description this command is used to remove dynamic arp table entries from the switch’s arp table. Static arp table entries are not af...

  • Page 169: Routing Table Commands

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 166 28 routing table commands the routing table commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create iproute [default] {} delete iprout...

  • Page 170

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 167 des-3526:4#delete iproute default 10.53.13.254 command: delete iproute default 10.53.13.254 success. Des-3526:4# show iproute purpose used to display the switch’s current ip routing table. Syntax show iproute description thi...

  • Page 171: Mac Notification Commands

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 168 29 mac notification commands the mac notification commands in the command line interface (cli) are listed, in the following table, along with their appropriate parameters. Command parameters enable mac_notification disable m...

  • Page 173

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 170 show mac_notification purpose used to display the switch’s mac address table notification global settings syntax show mac_notification description this command is used to display the switch’s mac address table notification g...

  • Page 174

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 171 des-3526:4#show mac_notification ports command: show mac_notification ports port # mac address table notification state ------ ----------------------------------------------------- 1 disabled 2 disabled 3 disabled 4 disabled...

  • Page 175

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 172 30 access authentication control commands the tacacs / xtacacs / tacacs+ / radius commands let you secure access to the switch using the tacacs / xtacacs / tacacs+ / radius protocols. When a user logs in to the switch or tri...

  • Page 177

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 174 enable authen_policy purpose used to enable system access authentication policy. Syntax enable authen_policy description this command will enable an administrator-defined authentication policy for users trying to access the ...

  • Page 178

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 175 example usage: to display the system access authentication policy: des-3526:4#show authen_policy command: show authen_policy authentication policy: enabled des-3526:4# create authen_login method_list_name purpose used to cre...

  • Page 179

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 176 config authen_login privilege only. If the user wishes to upgrade his or her status to the administrator level, the user must implement the enable admin command, followed by a previously configured password. ( see the enable...

  • Page 180

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 177 example usage: to configure the user defined method list “trinity” with authentication methods tacacs, xtacacs and local, in that order. Des-3526:4#config authen_login method_list_name trinity method tacacs xtacacs local com...

  • Page 181

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 178 show authen_login 15 characters to define the given method list the user wishes to view. All – entering this parameter will display all the authentication login methods currently configured on the switch. The window will dis...

  • Page 182

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 179 des-3526:4#create authen_enable method_list_name permit command: show authen_login method_list_name permit success. Des-3526:4# config authen_enable purpose used to configure a user-defined method list of authentication meth...

  • Page 183

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 180 config authen_enable none – adding this parameter will require no authentication to access the switch. Method_list_name – enter a previously implemented method list name defined by the user ( create authen_enable ). The user...

  • Page 184

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 181 delete authen_enable method_list_name purpose used to delete a user-defined method list of authentication methods for promoting normal user level privileges to administrator level privileges on the switch. Syntax delete auth...

  • Page 185

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 182 example usage: to display all method lists for promoting user level privileges to administrator level privileges. Des-3526:4#show authen_enable all command: show authen_enable all method list name priority method name commen...

  • Page 186

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 183 des-3526:4#config authen application http login default command: config authen application http login default success. Des-3526:4# show authen application purpose used to display authentication methods for the various applic...

  • Page 187

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 184 create authen server_host xtacacs - enter this parameter if the server host utilizes the xtacacs protocol. Tacacs+ - enter this parameter if the server host utilizes the tacacs+ protocol. Radius - enter this parameter if the...

  • Page 188

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 185 config authen server_host protocol – the protocol used by the server host. The user may choose one of the following: tacacs – enter this parameter if the server host utilizes the tacacs protocol. Xtacacs - enter this paramet...

  • Page 189

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 186 delete authen server_host xtacacs protocol . Tacacs+ - enter this parameter if the server host utilizes the tacacs+ protocol. Radius - enter this parameter if the server host utilizes the radius protocol. Restrictions only a...

  • Page 190

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 187 create authen server_group purpose used to create a user-defined authentication server group. Syntax create authen server_group description this command will create an authentication server group. A server group is a techniq...

  • Page 191

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 188 config authen server_group add/delete – enter the correct parameter to add or delete a server host from a server group. Server_host - enter the ip address of the previously configured server host to add or delete. Protocol –...

  • Page 192

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 189 show authen server_group purpose used to view authentication server groups on the switch. Syntax show authen server_group description this command will display authentication server groups currently configured on the switch....

  • Page 193

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 190 des-3526:4# config authen parameter response_timeout 60 command: config authen parameter response_timeout 60 success. Des-3526:4# config authen parameter attempt purpose used to configure the maximum number of times the swit...

  • Page 194

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 191 des-3526:4#show authen parameter command: show authen parameter response timeout : 60 seconds user attempts : 5 des-3526:4# enable admin purpose used to promote user level privileges to administrator level privileges syntax ...

  • Page 195

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 192 des-3526:4#config admin local_enable command: config admin local_enable enter the old password: enter the case-sensitive new password:****** enter the new password again for confirmation:****** success. Des-3526:4#.

  • Page 196: Ssh Commands

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 193 31 ssh commands the steps required to use the secure shell (ssh) protocol for secure communication between a remote pc (the ssh client) and the switch (the ssh server), are as follows: create a user account with admin-level ...

  • Page 197

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 194 des-3526:4#enable ssh command: enable ssh success. Des-3526:4# disable ssh purpose used to disable ssh. Syntax disable ssh description this command allows you to disable ssh on the switch. Parameters none. Restrictions only ...

  • Page 198

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 195 des-3526:4#config ssh authmode password enable command: config ssh authmode password enable success. Des-3526:4# show ssh authmode purpose used to display the ssh authentication mode setting. Syntax show ssh authmode descrip...

  • Page 199

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 196 des-3526:4# config ssh server maxsession 2 contimeout 300 authfail 2 command: config ssh server maxsession 2 contimeout 300 authfail 2 success. Des-3526:4# show ssh server purpose used to display the ssh server setting. Synt...

  • Page 200

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 197 config ssh user administrator defined password for authentication. Upon entry of this command, the switch will prompt the user for a password, and then to retype the password for confirmation. • publickey – this parameter sh...

  • Page 202

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 199 usage example: to display ssh algorithms currently set on the switch: des-3526:4#show ssh algorithm command: show ssh algorithm encryption algorithm 3des :enabled aes128 :enabled aes192 :enabled aes256 :enabled arc4 :enabled...

  • Page 203: Ssl Commands

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 200 32 ssl commands secure sockets layer or ssl is a security feature that will provide a secure communication path between a host and client through the use of authentication, digital signatures and encryption. These security f...

  • Page 206

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 203 config ssl cachetimeout timeout parameters timeout - enter a timeout value between 60 and 86400 seconds to specify the total time an ssl key exchange id stays valid before the ssl module will require a new, full ssl negotiat...

  • Page 207

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 204 des-3526:4#show ssl command: show ssl ssl status disabled rsa_with_rc4_128_md5 0x0004 enabled rsa_with_3des_ede_cbc_sha 0x000a enabled dhe_dss_with_3des_ede_cbc_sha 0x0013 enabled rsa_export_with_rc4_40_md5 0x0003 enabled de...

  • Page 208

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 205 des-3526:4# des-3526:4#download certificate_fromtftp 10.53.13.94 certfilename c:/cert.Der keyfilename c:/pkey.Der command: download certificate_fromtftp 10.53.13.94 certfilename c:/cert.Der keyfilename c:/pkey.Der certificat...

  • Page 209

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 206 33 d-link single ip management commands simply put, d-link single ip management is a concept that will stack switches together over ethernet instead of using stacking ports or modules. Switches using d-link single ip managem...

  • Page 210

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 207 when a cs becomes a ms, it automatically becomes a member of the first snmp community (include read/write and read only) to which the cs belongs. However if a ms has its own ip address, it can belong to snmp communities to w...

  • Page 212

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 209 to show the sim information in detail: des-3526:4#show sim command: show sim sim version : ver-1 firmware version : build 2.00-b02 device name : mac address : 00-35-26-11-11-00 capabilities : l3 platform : des-3526 l2 switch...

  • Page 213

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 210 to show other groups information in summary, if group is specified: des-3526:4#show sim group command: show sim group sim group name : default id mac address platform / hold firmware device name capability time version --- -...

  • Page 215

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 212 config sim parameters commander – use this parameter to configure the commander switch(cs) for the following parameters: group_name - used to update the name of the group. Enter an alphanumeric string of up to 64 characters ...

  • Page 216

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 213 to transfer the switch to be a cs: des-3526:4# config sim commander command: config sim commander success. Des-3526:4# to update the name of a group: des-3526:4# config sim commander group_name trinity command: config sim co...

  • Page 217

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 214 id mac address result --- ----------------- ---------------- 1 00-01-02-03-04-00 success 2 00-07-06-05-04-03 success 3 00-07-06-05-04-03 success des-3526:4# to download configuration files: des-3526:4# download sim configura...

  • Page 218: Command History List

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 215 34 command history list the switch history commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters ? Dir config command_history show command_...

  • Page 219

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 216 dir purpose used to display all commands in the command line interface (cli). Syntax dir description this command will display all of the commands available through the command line interface (cli). Parameters none. Restrict...

  • Page 220

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 217 show command_history purpose used to display the command history. Syntax show command_history description this command will display the command history. Parameters none. Restrictions none. Example usage to display the comman...

  • Page 221: Technical Specifications

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 218 a technical specifications general standards ieee 802.3 10base-t ethernet ieee 802.3u 100base-tx fast ethernet ieee 802.3ab 1000base-t gigabit ethernet ieee 802.3z 1000base-t (sfp “mini gbic”) ieee 802.1d spanning tree ieee ...

  • Page 222

    Des-3526 / des-3526dc layer 2 fast ethernet switch cli reference manual 219 physical and environmental internal power supply des-3526 ac input: 100 – 120; 200 – 240 vac, 50/60 hz des-3526 dc 60w dc power input: 48 v output: 12v power consumption 23 watts maximum dc fans: one 40 mm fan operating temp...