- DL manuals
- D-Link
- Switch
- Xstack DGS-3300 Series
- User Manual
D-Link Xstack DGS-3300 Series User Manual - Cli
xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet Switch CLI Manual
4
2
U
SING THE
C
ONSOLE
CLI
The xStack DGS/DXS-3300 Series supports a console management interface that allows the user to connect to the Switch’s
management agent via a serial port and a terminal or a computer running a terminal emulation program. The console can also be
used over the network using the TCP/IP Telnet protocol. The console program can be used to configure the Switch to use an
SNMP-based network management software over the network.
This chapter describes how to use the console interface to access the Switch, change its settings, and monitor its operation.
Note: Switch configuration settings are saved to non-volatile RAM using
the save command. The current configuration will then be retained in the
Switch’s NV-RAM, and reloaded when the Switch is rebooted. If the
Switch is rebooted without using the save command, the last configuration
saved to NV-RAM will be loaded.
Connecting to the Switch
The console interface is used by connecting the Switch to a VT100-compatible terminal or a computer running an ordinary
terminal emulator program (e.g., the HyperTerminal program included with the Windows operating system) using an RS-232C
serial cable. Your terminal parameters will need to be set to:
• VT-100 compatible
• 115200 baud
• 8 data bits
• No parity
• One stop bit
• No flow control
The same functions can be accessed over a Telnet interface. Once an IP address has been set for your Switch, a Telnet program
(in VT-100 compatible terminal mode) can be used to access and control the Switch. All of the screens are identical, whether
accessed from the console port or from a Telnet interface.
After the Switch reboots and the user has logged in, the console looks like this:
Summary of Xstack DGS-3300 Series
Page 1
©copyright 2006. All rights reserved. Cli manual product model : xstack tm dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch release 4.4.
Page 2: Table of Contents
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual table of contents introduction ................................................................................................................................................................... 1 using the console cli ....
Page 3
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual rip commands ..........................................................................................................................................................297 dvmrp commands......................................
Page 4
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 1 1 i ntroduction the dgs/dxs-3300 layer 3 stackable gigabit ethernet switches are members of the d-link xstack family. Ranging from 10/100mbps edge switches to core gigabit switches, the xstack switch family has been fu...
Page 5
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 2 there is no initial username or password. Just press the enter key twice to display the cli input cursor − dgs-3324sri:4#. This is the command line where all commands are input. Setting the switch’s ip address each swi...
Page 6
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 3 figure 1-3. Assigning an ip address in the above example, the switch was assigned an ip address of 10.53.13.144 with a subnet mask of 255.0.0.0. The system message success indicates that the command was executed succes...
Page 7: Cli
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 4 2 u sing the c onsole cli the xstack dgs/dxs-3300 series supports a console management interface that allows the user to connect to the switch’s management agent via a serial port and a terminal or a computer running a...
Page 8
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 5 figure 2-1. Initial console screen commands are entered at the command prompts, dgs-3324sri:4#, dgs-3324sr:4#, dxs-3326gsr:4#, dxs-3350sr:4#. There are a number of helpful features included in the cli. Entering the ? C...
Page 9
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 6 figure 2-3. Example command parameter help in this case, the command config account was entered with the parameter . The cli will then prompt to enter the with the message, next possible completions:. Every command in ...
Page 10
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 7 if a command is entered that is unrecognized by the cli, the top-level commands will be displayed under the available commands: prompt. Figure 2-5. The available commands prompt the top-level commands consist of comman...
Page 11
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 8 3 c ommand s yntax the following symbols are used to describe how command entries are made and values and arguments are specified in this manual. The online help contained in the cli and available through the console i...
Page 15
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 12 to configure the user password of “dlink” account: dgs-3324sri:4#config account dlink command: config account dlink enter a old password:**** enter a case-sensitive new password:**** enter the new password again for c...
Page 16
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 13 dgs-3324sri:4#delete account system command: delete account system are you sure to delete the last administrator account?(y/n)y success. Dgs-3324sri:4# example usage: to delete the user account “system2”: dgs-3324sri:...
Page 17
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 14 dgs-3324sri:4# show config config_in_nvram command: show config config_in_nvram #------------------------------------------------------------------------------------------------------ # dgs-3324sri configuration # # f...
Page 18
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 15 show switch purpose used to display information about the switch. Syntax show switch description this command displays information about the switch. Parameters none. Restrictions none. Example usage: to display the sw...
Page 19
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 16 dgs-3324sri:4#show switch command: show switch device type : dgs-3324sri stackable ethernet switch unit id : 1 mac address : da-10-21-00-00-01 ip address : 10.41.44.22 (manual) vlan name : default subnet mask : 255.0....
Page 20
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 17 show switch_mode purpose used to display the current switch mode. Syntax show switch_mode description this command displays the current mode of operation of the switch. Parameters none. Restrictions none. Example usag...
Page 21
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 18 show module_info purpose to show information concerning the added uplink module. Syntax show module_info description this command is used to view information about the dem-420x and dem-420cx uplink modules added to an...
Page 22
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 19 show serial_port purpose used to display the current serial port settings. Syntax show serial_port description this command displays the current serial port settings. Parameters none. Restrictions none. Example usage:...
Page 23
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 20 example usage: to configure baud rate: dgs-3324sri:4#config serial_port baud_rate 115200 command: config serial_port baud_rate 115200 success. Dgs-3324sri:4# enable clipaging purpose used to pause the scrolling of the...
Page 24
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 21 dgs-3324sri:4#disable clipaging command: disable clipaging success. Dgs-3324sri:4# enable telnet purpose used to enable communication with and management of the switch using the telnet protocol. Syntax enable telnet d...
Page 25
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 22 dgs-3324sri:4#disable telnet command: disable telnet success. Dgs-3324sri:4# enable web purpose used to enable the http-based management software on the switch. Syntax enable web description this command is used to en...
Page 27
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 24 reboot restrictions none. Example usage: to restart the switch: dgs-3324sri:4#reboot command: reboot are you sure want to proceed with the system reboot? (y/n) please wait, the switch is rebooting... Reset purpose use...
Page 28
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 25 login purpose used to log in a user to the switch’s console. Syntax login description this command is used to initiate the login procedure. The user will be prompted for his username and password. Parameters none. Res...
Page 31
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 28 to display the configuration of all ports on a standalone switch: dgs-3324sri:4#show ports command: show ports port port settings connection address state speed/duplex/flowctrl speed/duplex/flowctrl learning ------ --...
Page 33
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 30 to configure the port security: dgs-3324sri:4#config port_security ports 5:1-5:5 admin_state enable max_learning_addr 5 lock_address_mode deleteonreset command: config port_security ports 5:1-5:5 admin_state enable ma...
Page 34
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 31 delete port_security_entry_vlan_name purpose used to delete an entry from the switch’s port security settings. Syntax delete port_security_entry_vlan_name port mac_address description this command is used to remove an...
Page 35: (Snmp) C
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 32 7 n etwork m anagement (snmp) c ommands the network management commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. The xstack dgs/dxs-3300 series sup...
Page 36
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 33 command parameters delete snmp host show snmp host create trusted_host delete trusted_host show trusted_host enable snmp traps enable snmp authenticate_traps show snmp traps disable snmp traps disable snmp authenticat...
Page 37
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 34 create snmp user parameters − an alphanumeric name of up to 32 characters that will identify the new snmp user. − an alphanumeric name of up to 32 characters that will identify the snmp group the new snmp user will be...
Page 38
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 35 to create an snmp user on the switch: dgs-3324sri:4#create snmp user dlink default encrypted by_password auth md5 auth_password priv none command: create snmp user dlink default encrypted by_password auth md5 auth_pas...
Page 39
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 36 dgs-3324sri:4#show snmp user command: show snmp user username group name verauthpriv --------------- -------------------- --------------------- initial initial v3 none none total entries: 1 dgs-3324sri:4# create snmp ...
Page 40
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 37 delete snmp view − the object id that identifies an object tree (mib tree) that will be deleted from the switch. Restrictions only administrator-level users can issue this command. Example usage: to delete a previousl...
Page 41
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 38 create snmp community purpose used to create an snmp community string to define the relationship between the snmp manager and an agent. The community string acts like a password to permit access to the agent on the sw...
Page 42
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 39 delete snmp community description the delete snmp community command is used to remove a previously defined snmp community string from the switch. Parameters − an alphanumeric string of up to 32 characters that is used...
Page 43
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 40 config snmp engineid purpose used to configure a name for the snmp engine on the switch. Syntax config snmp engineid description the config snmp engineid command configures a name for the snmp engine on the switch. Pa...
Page 45
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 42 example usage: to create an snmp group named “sg1:” dgs-3324sri:4#create snmp group sg1 v3 noauth_nopriv read_view v1 write_view v1 notify_view v1 command: create snmp group sg1 v3 noauth_nopriv read_view v1 write_vie...
Page 46
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 43 dgs-3324sri:4#show snmp groups command: show snmp groups vacm access table settings group name : group3 readview name : readview writeview name : writeview notify view name : notifyview security model : snmpv3 securit...
Page 48
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 45 delete snmp host purpose used to remove a recipient of snmp traps generated by the switch’s snmp agent. Syntax delete snmp host description the delete snmp host command deletes a recipient of snmp traps generated by t...
Page 49
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 46 dgs-3324sri:4#show snmp host command: show snmp host snmp host table host ip address snmp version community name/snmpv3 user name --------------- --------------------- ------------------------------ 10.48.76.23 v2c pr...
Page 50
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 47 to display the list of trust hosts: dgs-3324sri:4#show trusted_host command: show trusted_host management stations ip address -------------------- 10.53.13.94 total entries: 1 dgs-3324sri:4# delete trusted_host purpos...
Page 51
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 48 dgs-3324sri:4#enable snmp traps command: enable snmp traps success. Dgs-3324sri:4# enable snmp authenticate_traps purpose used to enable snmp authentication trap support. Syntax enable snmp authenticate_traps descript...
Page 52
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 49 disable snmp traps purpose used to disable snmp trap support on the switch. Syntax disable snmp traps description this command is used to disable snmp trap support on the switch. Parameters none. Restrictions only adm...
Page 53
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 50 config snmp system_contact purpose used to enter the name of a contact person who is responsible for the switch. Syntax config snmp system_contact {} description the config snmp system_contact command is used to enter...
Page 54
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 51 config snmp system_name purpose used to configure the name for the switch. Syntax config snmp system_name {} description the config snmp system_name command configures the name of the switch. Parameters - a maximum of...
Page 55
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 52 disable rmon purpose used to disable rmon on the switch. Syntax disable rmon description this command is used, in conjunction with the enable rmon command above, to enable and disable remote monitoring (rmon) on the s...
Page 56
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 53 8 s witch u tility c ommands the switch utility commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Please note that commands concerning the compactf...
Page 57
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 54 download parameters firmware_fromtftp − download and install new firmware on the switch from a tftp server. Firmware_fromcf − download and install new firmware on the switch from a compactflash server. Cfg_fromtftp - ...
Page 58
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 55 download prom_fromtftp be on the same ip subnet as the switch. − the dos path and filename of the prom code on the tftp server or compactflash card. For example, c:\3226sprom.Had. Restrictions only administrator-level...
Page 59
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 56 upload parameters cfg_totftp − specifies that the switch’s current settings will be uploaded to the tftp server. Log_totftp − specifies that the switch’s current log will be uploaded to the tftp server. Firmware_tocf ...
Page 60
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 57 config firmware delete – selecting this parameter, along with the image_id will delete this firmware from the switch’s memory. Boot_up - selecting this parameter, along with the image_id will set this firmware as the ...
Page 61
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 58 dgs-3324sri:4#show firmware information command: show firmware information box id version size(b) update time from user --- -- -------- ------- ------------------- ------------------ --------------- 1 *1 4.00-b02 2360...
Page 63
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 60 9 n etwork m onitoring c ommands the network monitoring commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters show packet ports show...
Page 64
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 61 show packet ports purpose used to display statistics about the packets sent and received by the switch. Syntax show packet ports description this command is used to display statistics about packets sent and received b...
Page 65
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 62 show error ports parameters − specifies a range of ports to be displayed. The port list is specified by listing the lowest switch number and the beginning port number on that switch, separated by a colon. Then the hig...
Page 66
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 63 dgs-3324sri:4#show utilization ports command: show utilization ports port tx/sec rx/sec util port tx/sec rx/sec util ---- ---------- ---------- ---- ---- ---------- ---------- ---- 1:1 0 0 0 1:22 0 0 0 1:2 0 0 0 1:23 ...
Page 67
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 64 example usage: to clear the counters: dgs-3324sri:4#clear counters ports 2:7-2:9 command: clear counters ports 2:7-2:9 success. Dgs-3324sri:4# clear log purpose used to clear the switch’s history log. Syntax clear log...
Page 68
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 65 dgs-3324sri:4#show log index 1-4 command: show log index 1-4 index date time log text ----- ---------- -------- ----------------------------------------------------- 4 2000-03-02 01:54:53 port 1:13 link up, 100mbps fu...
Page 69
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 66 dgs-3324sri:4#disable syslog command: disable syslog success. Dgs-3324sri:4# show syslog purpose used to display the syslog protocol status as enabled or disabled. Syntax show syslog description the show syslog comman...
Page 70
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 67 create syslog host parameters − specifies that the command will be applied to an index of hosts. There are four available indexes, numbered 1 through 4. Severity − severity level indicator, as shown below: bold font i...
Page 71
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 68 create syslog host 17 local use 1 (local1) 18 local use 2 (local2) 19 local use 3 (local3) 20 local use 4 (local4) 21 local use 5 (local5) 22 local use 6 (local6) 23 local use 7 (local7) local0 − specifies that local ...
Page 73
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 70 8 uucp subsystem 9 clock daemon 10 security/authorization messages 11 ftp daemon 12 ntp subsystem 13 log audit 14 log alert 15 clock daemon 16 local use 0 (local0) 17 local use 1 (local1) 18 local use 2 (local2) 19 lo...
Page 74
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 71 dgs-3324sri:4# config syslog host 1 udp_port 6000 command: config syslog host 1 udp_port 6000 success. Dgs-3324sri:4# config syslog host 1 ipaddress 10.44.67.8 command: config syslog host 1 ipaddress 10.44.67.8 succes...
Page 75
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 72 config syslog host all facility − some of the operating system daemons and processes have been assigned facility values. Processes and daemons that have not been explicitly assigned a facility may use any of the "loca...
Page 77
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 74 dgs-3324sri:4#delete syslog host 4 command: delete syslog host 4 success. Dgs-3324sri:4# show syslog host purpose used to display the syslog hosts currently configured on the switch. Syntax show syslog host {} descrip...
Page 79
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 76 dgs-3324sri:4#config system_severity trap critical command: config system_severity trap critical success. Dgs-3324sri:4# show system_severity purpose to display the current severity settings set on the switch. Syntax ...
Page 80: (Mstp) C
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 77 10 m ultiple s panning t ree p rotocol (mstp) c ommands this switch supports three versions of the spanning tree protocol; 802.1d stp, 802.1w rapid stp and 802.1s mstp. Multiple spanning tree protocol, or mstp, is a s...
Page 83
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 80 config stp parameters maxage − this value may be set to ensure that old information does not endlessly circulate through redundant paths in the network, preventing the effective propagation of the new information. Set...
Page 87
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 84 delete stp instance_id purpose used to delete a stp instance id from the switch. Syntax delete stp instance_id description this command allows the user to delete a previously configured stp instance id from the switch...
Page 89
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 86 config stp mst_ports parameters - specifies a port or range of ports to be configured. The port list is specified by listing the lowest switch number and the beginning port number on that switch, separated by a colon....
Page 90
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 87 example usage: to display the status of stp on the switch: status 1: stp enabled with stp compatible version dgs-3324sri:4#show stp command: show stp stp status : enabled stp version : stp compatible max age : 20 hell...
Page 91
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 88 show stp ports purpose used to display the switch’s current instance_id configuration. Syntax show stp ports description this command displays the stp instance settings and stp instance operational status currently im...
Page 92
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 89 dgs-3324sri:4#show stp instance 0 command: show stp instance 0 stp instance settings --------------------------- instance type : cist instance status : enabled instance priority : 32768(bridge priority : 32768, sys id...
Page 93
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 90 11 f orwarding d atabase c ommands the forwarding database commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create fdb port cre...
Page 94
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 91 dgs-3324sri:4#create fdb default 00-00-00-00-01-02 port 2:5 command: create fdb default 00-00-00-00-01-02 port 2:5 success. Dgs-3324sri:4# create multicast_fdb purpose used to create a static entry to the multicast ma...
Page 96
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 93 example usage: to set the fdb aging time: dgs-3324sri:4#config fdb aging_time 300 command: config fdb aging_time 300 success. Dgs-3324sri:4# delete fdb purpose used to delete an entry to the switch’s forwarding databa...
Page 98
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 95 dgs-3324sri:4#show multicast_fdb command: show multicast_fdb vlan name : default mac address : 01-00-5e-00-00-00 egress ports : 1:1-1:5,1:26,2:26 mode : static total entries : 1 dgs-3324sri:4# show fdb purpose used to...
Page 99
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 96 dgs-3324sri:4#show fdb command: show fdb unicast mac address aging time = 300 vid vlan name mac address port type ---- ---------------- ----------------- ------ ---------------- 1 default 00-00-39-34-66-9a 1:12 dynami...
Page 100
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 97 dgs-3324sri:4#show ipfdb command: show ipfdb interface ip address port learned ------------ --------------- ------ ------------ system 10.0.0.1 1:13 dynamic system 10.0.0.2 1:13 dynamic system 10.0.0.3 1:13 dynamic sy...
Page 101
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 98 show fdb destination_hit purpose to view the destination hit status of the switch. Syntax show fdb destination_hit description this command will allow users to view the destination hit status of the switch. Parameters...
Page 102
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 99 12 b roadcast s torm c ontrol c ommands the broadcast storm control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config tra...
Page 103
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 100 dgs-3324sri:4#config traffic control all broadcast enable command: config traffic control all broadcast enable success. Dgs-3324sri:4# show traffic control purpose used to display current traffic control settings. Sy...
Page 104: S C
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 101 13 q o s c ommands the xstack dgs/dxs-3300 series support 802.1p priority queuing. These switches has eight classes of service for each port on the switch, one of which is internal and unconfigurable to the user. The...
Page 106
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 103 example usage: to configure bandwidth control: dgs-3324sri:4#config bandwidth_control 1:1-1:10 tx_rate 10 command: config bandwidth_control 1:1-1:10 tx_rate 10 success. Dgs-3324sri:4# show bandwidth_control purpose u...
Page 107
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 104 config scheduling purpose used to configure traffic scheduling for each of the switch’s hardware priority classes. Syntax config scheduling {max_packet } description the switch contains seven hardware classes of serv...
Page 108
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 105 notice: the default qos scheduling arrangement is a strict priority schedule. To customize scheduling to set up weighted or round-robin class clearing, the max_packets values need to be changed. Example usage: to con...
Page 109
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 106 dgs-3324sri:4# show scheduling command: show scheduling qos output scheduling max. Packets ------------------- class-0 1 class-1 0 class-2 3 class-3 4 class-4 5 class-5 6 class-6 7 dgs-3324sri:4# config 802.1p user_p...
Page 110
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 107 dgs-3324sri:4# show 802.1p user_priority purpose used to display the current 802.1p user priority tags to hardware priority class of service mapping in use by the switch. Syntax show 802.1p user_priority description ...
Page 111
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 108 config 802.1p default_priority restrictions only administrator-level users can issue this command. Example usage: to configure 802.1p default priority on the switch: dgs-3324sri:4#config 802.1p default_priority all 5...
Page 112
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 109 1:14 0 1:15 0 1:16 0 1:17 0 1:18 0 1:19 0 1:20 0 1:21 0 1:22 0 1:23 0 1:24 0 dgs-3324sri:4# config scheduling_mechanism purpose used to configure the scheduling mechanism for the qos function syntax config scheduling...
Page 113
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 110 show scheduling_mechanism purpose used to display the current traffic scheduling mechanisms in use on the switch. Syntax show scheduling_mechanism description this command will display the current traffic scheduling ...
Page 114
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 111 disable hol_prevention purpose used to disable hol prevention. Syntax disable hol_prevention description thedisable hol_preventioncommand disables head of line prevention. Parameters none. Restrictions only administr...
Page 116
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 113 example usage: to add the mirroring ports: dgs-3324sri:4# config mirror port 1:10 add source ports 1:1-1:5 both command: config mirror port 1:10 add source ports 1:1-1:5 both success. Dgs-3324sri:4# config mirror por...
Page 117
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 114 dgs-3324sri:4#config mirror port 1:10 delete source port 1:1-1:5 both command: config mirror 1:10 delete source 1:1-1:5 both success. Dgs-3324sri:4# enable mirror purpose used to enable a previously entered port mirr...
Page 118
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 115 dgs-3324sri:4#disable mirror command: disable mirror success. Dgs-3324sri:4# show mirror purpose used to show the current port mirroring configuration on the switch. Syntax show mirror description this command displa...
Page 119: Vlan C
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 116 15 vlan c ommands the xstack dgs/dxs-3300 series now incorporates protocol-based vlans. This standard, defined by the ieee 802.1v standard maps packets to protocol-defined vlans by examining the type octet within the...
Page 121
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 118 create vlan protocol-ipxethernet2 - using this parameter will instruct the switch to forward packets to this vlan if the tag in the packet header is concurrent with this protocol. This packet header information is de...
Page 123
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 120 to remove the vlan “v1”: dgs-3324sri:4#delete vlan v1 command: delete vlan v1 success. Dgs-3324sri:4# config vlan add purpose used to add additional ports to a previously configured vlan. Syntax config vlan {[add [ t...
Page 124
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 121 config vlan delete purpose used to delete ports from a previously configured vlan. Syntax config vlan delete description this command is used to delete ports from the port list of a previously configured vlan. Parame...
Page 125
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 122 config gvrp parameters − a range of ports for which to configure gvrp. The port list is specified by listing the lowest switch number and the beginning port number on that switch, separated by a colon. Then the highe...
Page 126
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 123 dgs-3324sri:4#enable gvrp command: enable gvrp success. Dgs-3324sri:4# disable gvrp purpose used to disable gvrp on the switch. Syntax disable gvrp description this command, along with enable gvrp below, is used to e...
Page 127
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 124 dgs-3324sri:4#show vlan command: show vlan vid : 1 vlan name : default vlan type : 1qvlan protocol id : userdefinedpid : advertisement : enabled encap : member ports : 1:1-1:24,2:1-2:24 static ports : 1:1-1:24,2:1-2:...
Page 128
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 125 dgs-3324sri:4#show gvrp command: show gvrp global gvrp : disabled port pvid gvrp ingress checking acceptable frame type ------ ---- -------- ---------------- --------------------------- 1:1 1 disabled enabled all fra...
Page 129
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 126 16 l ink a ggregation c ommands the link aggregation commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create link_aggregation ...
Page 130
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 127 dgs-3324sri:4#create link_aggregation group_id 1 command: create link_aggregation group_id 1 success. Dgs-3324sri:4# delete link_aggregation group_id purpose used to delete a previously configured link aggregation gr...
Page 131
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 128 config link_aggregation master_port − master port id. Specifies which port (by port number) of the link aggregation group will be the master port. All of the ports in a link aggregation group will share the port conf...
Page 132
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 129 config link_aggregation algorithm mac source and destination addresses. Ip_source − indicates that the switch should examine the ip source address. Ip_destination − indicates that the switch should examine the ip des...
Page 134
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 131 show lacp_port purpose used to display current lacp port mode settings. Syntax show lacp_port {} description this command will display the lacp mode settings as they are currently configured. Parameters - specifies a...
Page 135: Ip C
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 132 17 ip c ommands (i ncluding ip m ultinetting ) ip multinetting is a function that allows multiple ip interfaces to be assigned to the same vlan. This is beneficial to the administrator when the number of ips on the o...
Page 138
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 135 to enable the ipif function on the switch: dgs-3324sri:4#enable ipif s2 command: enable ipif s2 success. Dgs-3324sri:4# disable ipif purpose used to disable the configuration of an ip interface on the switch. Syntax ...
Page 139
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 136 to delete the ip interface named s2: dgs-3324sri:4#delete ipif s2 command: delete ipif s2 success. Dgs-3324sri:4# show ipif purpose used to display the configuration of an ip interface on the switch. Syntax show ipif...
Page 140: Igmp C
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 137 18 igmp c ommands (i ncluding igmp v 3) igmp or internet group management protocol is a protocol implemented by systems utilizing ipv4 to collect the membership information needed by the multicast routing protocol th...
Page 142
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 139 to display igmp configurations: dgs-3324sri:4#show igmp command: show igmp igmp interface configurations interface ip address/netmask ver- query maximum robust- last state sion response ness member time value query i...
Page 143
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 140 dgs-3324sri:4#show igmp group group 224.0.1.1 ipif system command: show igmp group group 224.0.1.1 ipif system igmp group detail information interface : system multicast group : 224.0.1.1 last reporter : 10.50.77.16 ...
Page 145
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 142 config igmp_snooping host_timeout − specifies the maximum amount of time a host can be a member of a multicast group without the switch receiving a host membership report. The default is 260 seconds. Router_timeout −...
Page 146
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 143 config igmp_snooping querier query_interval − specifies the amount of time in seconds between general query transmissions. The default setting is 125 seconds. Max_response_time − specifies the maximum time in seconds...
Page 147
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 144 enable igmp_snooping purpose used to enable igmp snooping on the switch. Syntax enable igmp_snooping {forward_mcrouter_only} description this command allows the user to enable igmp snooping on the switch. If forward_...
Page 150
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 147 dgs-3324sri:4#show router_ports command: show router_ports vlan name : default static router port : 2:1-2:10 dynamic router port : forbidden router port: vlan name : vlan2 static router port : dynamic router port : f...
Page 151
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 148 dgs-3324sri:4#show igmp_snooping command: show igmp_snooping igmp snooping global state : disabled multicast router only : disabled vlan name : default query interval : 125 max response time : 10 robustness value : 2...
Page 152
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 149 dgs-3324sri:4#show igmp_snooping group command: show igmp_snooping group vlan name : default multicast group: 224.0.0.2 mac address : 01-00-5e-00-00-02 reports : 1 port member : 1:26,2:7 vlan name : default multicast...
Page 153
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 150 example usage: to view the igmp snooping forwarding table for vlan “trinity”: dgs-3324sri:4#show igmp_snooping forwarding vlan trinity command: show igmp_snooping forwarding vlan trinity vlan name : trinity multicast...
Page 154: Mac N
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 151 20 mac n otification c ommands the mac notification commands in the command line interface (cli) are listed, in the following table, along with their appropriate parameters. Command parameters enable mac_notification...
Page 155
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 152 example usage: to disable mac notification without changing basic configuration: dgs-3324sri:4#disable mac_notification command: disable mac_notification success. Dgs-3324sri:4# config mac_notification purpose used t...
Page 157
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 154 show mac_notification ports purpose used to display the switch’s mac address table notification status settings. Syntax show mac_notification ports description this command is used to display the switch’s mac address...
Page 158
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 155 21 a ccess a uthentication c ontrol c ommands the access authentication control commands allows secure access to the switch using the tacacs / xtacacs / tacacs+ and radius protocols. When a user logs in to the switch...
Page 159
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 156 the access authentication control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enable authen_policy disable authen_policy ...
Page 160
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 157 command parameters enable admin config admin local_enable each command is listed, in detail, in the following sections. Enable authen_policy purpose used to enable system access authentication policy. Syntax enable a...
Page 161
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 158 show authen_policy purpose used to display the system access authentication policy status on the switch. Syntax show authen_policy description this command will show the current status of the access authentication po...
Page 163
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 160 config authen_login method_list_name – enter a previously implemented method list name defined by the user. The user may add one, or a combination of up to four (4) of the following authentication methods to this met...
Page 164
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 161 delete authen_login method_list_name purpose used to delete a previously configured user defined method list of authentication methods for users logging on to the switch. Syntax delete authen_login method_list_name d...
Page 165
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 162 show authen_login parameters default – entering this parameter will display the default method list for users logging on to the switch. Method_list_name – enter an alphanumeric string of up to 15 characters to define...
Page 166
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 163 config authen_enable purpose used to configure a user-defined method list of authentication methods for promoting normal user level privileges to administrator level privileges on the switch. Syntax config authen_ena...
Page 167
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 164 config authen_enable method_list_name – enter a previously implemented method list name defined by the user (create authen_enable). The user may add one, or a combination of up to four (4) of the following authentica...
Page 168
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 165 delete authen_enable method_list_name purpose used to delete a user-defined method list of authentication methods for promoting normal user level privileges to administrator level privileges on the switch. Syntax del...
Page 169
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 166 show authen_enable parameters default – entering this parameter will display the default method list for users attempting to gain access to administrator level privileges on the switch. Method_list_name – enter an al...
Page 170
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 167 config authen application (console, telnet, web, ssh) login method. Login – use this parameter to configure an application for normal login on the user level, using a previously configured method list. Enable - use t...
Page 172
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 169 dgs-3324sri:4#create authen server_host 10.1.1.121 protocol tacacs+ port 1234 timeout 10 retransmit 5 command: create authen server_host 10.1.1.121 protocol tacacs+ port 1234 timeout 10 retransmit 5 success. Dgs-3324...
Page 173
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 170 config authen server_host timeout - enter the time in seconds the switch will wait for the server host to reply to an authentication request. The default value is 5 seconds. Retransmit - enter the value in the retran...
Page 174
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 171 dgs-3324sri:4#delete authen server_host 10.1.1.121 protocol tacacs+ command: delete authen server_host 10.1.1.121 protocol tacacs+ success. Dgs-3324sri:4# show authen server_host purpose used to view a user-defined a...
Page 175
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 172 create authen server_group purpose used to create a user-defined authentication server group. Syntax create authen server_group description this command will create an authentication server group. A server group is a...
Page 176
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 173 config authen server_group tacacs – use this parameter to utilize the built-in tacacs server protocol on the switch. Only server hosts utilizing the tacacs protocol may be added to this group. Xtacacs – use this para...
Page 177
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 174 example usage: to delete the server group “group_1”: dgs-3324sri:4#delete server_group group_1 command: delete server_group group_1 success. Dgs-3324sri:4# show authen server_group purpose used to view authentication...
Page 178
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 175 config authen parameter response_timeout purpose used to configure the amount of time the switch will wait for a user to enter authentication before timing out. Syntax config authen parameter response_timeout descrip...
Page 179
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 176 config authen parameter attempt parameters parameter attempt - set the maximum number of attempts the user may try to become authenticated by the switch, before being locked out. The default setting is 3 attempts. Re...
Page 180
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 177 enable admin will enter this command and will have to enter an authentication password. Possible authentication methods for this function include tacacs/xtacacs/tacacs+/radius, user defined server groups, local enabl...
Page 181
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 178 dgs-3324sri:4#config admin local_enable command: config admin local_enable enter the old password: ****** enter the case-sensitive new password:****** enter the new password again for confirmation:****** success. Dgs...
Page 182: Ssh
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 179 22 ssh c ommands the steps required to use the ssh protocol for secure communication between a remote pc (the ssh client) and the switch (the ssh server), are as follows: create a user account with admin-level access...
Page 183
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 180 enable ssh purpose used to enable ssh. Syntax enable ssh description this command will enable ssh on the switch. Parameters none. Restrictions only administrator-level users can issue this command. Usage example: to ...
Page 184
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 181 config ssh authmode parameters password – this parameter may be chosen if the administrator wishes to use a locally configured password for authentication on the switch. Publickey - this parameter may be chosen if th...
Page 185
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 182 dgs-3324sri:4#show ssh authmode command: show ssh authmode the ssh user authentication support ---- --------------------------------------------- password : enabled publickey : enabled hostbased : enabled dgs-3324sri...
Page 186
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 183 to display the ssh server: dgs-3324sri:4# show ssh server command: show ssh server ssh server status : disabled ssh max session : 3 connection timeout : 120 (sec) authenticate failed attempts : 2 rekey timeout : neve...
Page 187
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 184 dgs-3324sri:4# config ssh user trinity authmode password command: config ssh user trinity authmode password success. Dgs-3324sri:4# show ssh user authmode purpose used to display the ssh user setting. Syntax show ssh...
Page 188
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 185 config ssh algorithm aes192 - this parameter will enable or disable the advanced encryption standard aes192 encryption algorithm. Aes256 - this parameter will enable or disable the advanced encryption standard aes256...
Page 189
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 186 dgs-3324sri:4#show ssh algorithm command: show ssh algorithm encryption algorithm -------------------------------------- 3des :enabled aes128 :enabled aes192 :enabled aes256 :enabled arc4 :enabled blowfish :enabled c...
Page 190: Ssl C
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 187 23 ssl c ommands secure sockets layer or ssl is a security feature that will provide a secure communication path between a host and client through the use of authentication, digital signatures and encryption. These s...
Page 192
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 189 note: enabling the ssl function on the switch will disable the port for the web manager (port 80). To log on to the web based manager, the entry of your url must begin with https://. (ex. Https://10.90.90.90) disable...
Page 193
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 190 config ssl cachetimeout purpose used to configure the ssl cache timeout. Syntax config ssl cachetimeout description this command will set the time between a new key exchange between a client and a host using the ssl ...
Page 194
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 191 show ssl purpose used to view the ssl status and the certificate file status on the switch. Syntax show ssl {certificate} description this command is used to view the ssl status on the switch. Adding the certificate ...
Page 195
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 192 download certificate_fromtftp description this command is used to download a certificate file for the ssl function on the switch from a tftp server. The certificate file is a data record used for authenticating devic...
Page 196: 802.1X C
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 193 24 802.1x c ommands the xstack dgs/dxs-3300 series implement the server-side of the ieee 802.1x port-based and mac-based network access control. This mechanism is intended to allow only authorized users, or other net...
Page 198
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 195 create 802.1x user purpose used to create a new 802.1x user. Syntax create 802.1x user description the create 802.1x user command is used to create new 802.1x users. Parameters − a username of up to 15 alphanumeric c...
Page 199
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 196 delete 802.1x user purpose used to delete an 802.1x user account on the switch. Syntax delete 802.1x user description the delete 802.1x user command is used to delete the 802.1x port- based or mac-based network acces...
Page 200
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 197 show 802.1x auth_configuration port to become unauthorized. Quietperiod − shows the time interval between authentication failure and the start of a new authentication attempt. Txperiod − shows the time to wait for a ...
Page 202
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 199 dgs-3324sri:4#show 802.1x auth_state command: show 802.1x auth_state port auth pae state backend state port status ------ ----------------------- --------------------- ----------------- 1:1 forceauth success authoriz...
Page 204
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 201 dgs-3324sri:4#config 802.1x capability ports 1:1 – 1:10 authenticator command: config 802.1x capability ports 1:1 – 1:10 authenticator success. Dgs-3324sri:4# config 802.1x auth_parameter purpose used to configure th...
Page 205
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 202 config 802.1x auth_parameter parameters − specifies a range of ports. The port list is specified by listing the lowest switch number and the beginning port number on that switch, separated by a colon. Then the highes...
Page 206
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 203 dgs-3324sri:4#config 802.1x auth_parameter ports 1:1 – 1:20 direction both command: config 802.1x auth_parameter ports 1:1 – 1:20 direction both success. Dgs-3324sri:4# config 802.1x auth_protocol purpose used to con...
Page 207
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 204 config 802.1x init parameters port_based – this instructs the switch to initialize 802.1x functions based only on the port number. Ports approved for initialization can then be specified. Ports − specifies a range of...
Page 210
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 207 example usage: to delete previously configured radius server communication settings: dgs-3324sri:4#config radius delete 1 command: config radius delete 1 success. Dgs-3324sri:4# config radius purpose used to configur...
Page 211
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 208 show radius purpose used to display the current radius configurations on the switch. Syntax show radius description the show radius command is used to display the current radius configurations on the switch. Paramete...
Page 212
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 209 dgs-3324sri:4#show acct_client command: show acct_client radiusacctclient --------------------------------------------------------------------------------------- radiusacctclientinvalidserveraddresses 0 radiusacctcli...
Page 213
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 210 dgs-3324sri:4#show auth_client command: show auth_client radiusauthclient ---------------------------------------------------------------------------------------- radiusauthclientinvalidserveraddresses 0 radiusauthcl...
Page 214
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 211 dgs-3324sri:4#show auth_diagnostics ports 1:16 command: show auth_diagnostics ports 1:16 port number : 1:16 entersconnecting 0 eaplogoffswhileconnecting 0 entersauthenticating 0 successwhileauthenticating 0 timeoutsw...
Page 215
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 212 dgs-3324sri:4#show auth_session_statistics ports 1:16 command: show auth_session_statistics ports 1:16 port number : 1:16 sessionoctetsrx 0 sessionoctetstx 0 sessionframesrx 0 sessionframestx 0 sessionid sessionauthe...
Page 216
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 213 dgs-3324sri:4#show auth_statistics ports 1:16 command: show auth_statistics ports 1:16 port number : 1:16 eapolframesrx 0 eapolframestx 0 eapolstartframesrx 0 eapolreqidframestx 0 eapollogoffframesrx 0 eapolreqframes...
Page 217: (Acl) C
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 214 25 a ccess c ontrol l ist (acl) c ommands the xstack dgs/dxs-3300 series implement access control lists that enable the switch to deny network access to specific devices or device groups based on ip settings, mac add...
Page 219
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 216 access_id gives the rule a higher priority. In case of a conflict in the rules entered for an access profile, the rule with the highest priority (lowest access_id) will take precedence. The ip parameter instructs the...
Page 221
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 218 create access_profile (for ethernet) purpose used to create an access profile on the switch by examining the ethernet part of the packet header. Masks entered can be combined with the values the switch finds in the s...
Page 223
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 220 config access_profile profile_id (for ethernet) permit – specifies that packets that match the access profile are permitted to be forwarded by the switch. • priority − this parameter is specified to re-write the 802....
Page 224
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 221 create access_profile (ip) purpose used to create an access profile on the switch by examining the ip part of the packet header. Masks entered can be combined with the values the switch finds in the specified frame h...
Page 226
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 223 config access_profile profile_id (ip) description this command is used to define the rules used by the switch to either filter or forward packets based on the ip part of each packet header. Parameters profile_id - en...
Page 227
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 224 config access_profile profile_id (ip) • flag_mask – enter the type of tcp flag to be masked. The choices are: • urg: tcp control flag (urgent) • ack: tcp control flag (acknowledgement) • psh: tcp control flag (push) ...
Page 228
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 225 config access_profile profile_id (ip) mirror - selecting mirror specifies that packets that match the access profile are mirrored to a port defined in the config mirror port command. Port mirroring must be enabled an...
Page 229
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 226 create access_profile (packet content mask) description this command is used to identify packets by examining the ethernet packet header, by byte and then decide whether to filter or forward it, based on the user’s c...
Page 231
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 228 config access_profile profile_id (packet content mask) permit – specifies that packets that match the access profile are permitted to be forwarded by the switch. • priority − this parameter is specified to re-write t...
Page 232
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 229 create access_profile (ipv6) purpose used to create an access profile on the switch by examining the ipv6 part of the packet header. Masks can be entered that will be combined with the values the switch finds in the ...
Page 234
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 231 config access_profile profile_id (ipv6) • priority − this parameter is specified to re-write the 802.1p default priority previously set in the switch, which is used to determine the cos queue to which packets are for...
Page 235
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 232 delete access_profile description the delete access_profilecommand is used to delete a previously created access profile on the switch. Parameters profile_id − enter an integer between 1 and 8 that is used to identif...
Page 236
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 233 ports: 1:1 ----------- ------ trinity 1 ====================================================================== access profile id: 2 type : ip ====================================================================== mas...
Page 238
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 235 create cpu access_profile • igmp − specifies that the switch will examine each frame’s internet group management protocol (igmp) field. • type − specifies that the switch will examine each frame’s igmp type field. • ...
Page 239
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 236 create cpu access_profile • class – entering this parameter will instruct the switch to examine the class field of the ipv6 header. This class field is a part of the packet header that is similar to the type of servi...
Page 240
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 237 config cpu access_profile purpose used to configure a cpu access profile used for cpu interface filtering and to define specific values that will be used to by the switch to determine if a given packet should be forw...
Page 241
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 238 config cpu access_profile • ethernet_type − specifies that the access profile will apply only to packets with this hexadecimal 802.1q ethernet type value in the packet header. Ip − specifies that the switch will look...
Page 242
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 239 config cpu access_profile • packet_content_mask – specifies that the switch will mask the packet header beginning with the offset value specified as follows: • offset_0-15 - enter a value in hex form to mask the pack...
Page 243
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 240 enable cpu_interface_filtering purpose used to enable cpu interface filtering on the switch. Syntax enable cpu_interface_filtering description this command is used, in conjunction with the disable cpu_interface_filte...
Page 244
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 241 to show the cpu filtering state on the switch: dgs-3324sri:4#show cpu access_profile command: show cpu access_profile cpu interface filtering state: disabled cpu interface filtering access profile table access profil...
Page 245
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 242 26 t raffic s egmentation c ommands traffic segmentation allows further sub-division of vlans into smaller groups of ports that will help to reduce traffic on the vlan. The vlan rules take precedence, and then the tr...
Page 246
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 243 show traffic_segmentation purpose used to display the current traffic segmentation configuration on the switch. Syntax show traffic_segmentation description the show traffic_segmentation command is used to display th...
Page 247
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 244 27 s tacking c ommands the stacking configuration commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config box_priority current...
Page 249
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 246 usage example: to configure box type: dgs-3324sri:4#config box_type current_box_id 3 type box_notexist command: config box_type current_box_id 3 type box_notexist success. Dgs-3324sri:4# config all_boxes_id purpose u...
Page 250
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 247 dgs-3324sri:4#show stack_information command: show stack_information box user prio- prom runtime h/w id set type exist rity version version version --- ---- ----------- ----- ----- -------- -------- -------- 1 auto d...
Page 251: D-L
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 248 28 d-l ink s ingle ip m anagement c ommands simply put, d-link single ip management is a concept that will stack switches together over ethernet instead of using stacking ports or modules. Switches using single ip ma...
Page 252
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 249 b. If report packets from the cs to the ms time out. 5. The user can manually configure a cas to become a cs 6. The cas can be configured through the cs to become a ms. After configuring one switch to operate as the ...
Page 255
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 252 dgs-3324sri:4#show sim command: show sim group name : default sim version : ver-1.61 firmware version : build 4.30-b08 device name : mac address : 00-35-26-11-11-00 capabilities : l3 platform : dgs-3324sri l3 switch ...
Page 256
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 253 id mac address platform / hold firmware device name capability time version --- ----------------- ------------------------ ----- --------- ---------------- 2 00-55-55-00-55-00 dxs-3350 l3 switch 140 4.30-b08 enrico s...
Page 259
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 256 dgs-3324sri:4#config sim candidate command: config sim candidate success. Dgs-3324sri:4# to transfer the switch to be a commander: dgs-3324sri:4#config sim commander command: config sim commander success. Dgs-3324sri...
Page 260
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 257 example usage: to download firmware: dgs-3324sri:4# download sim_ms firmware 10.53.13.94 c:/dgssri.Had all command: download sim_ms firmware 10.53.13.94 c:/dgssri.Had all this device is updating firmware. Please wait...
Page 261
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 258 upload sim_ms configuration parameters configuration_to_tftp – choose this parameter to upload configuration files from sim members to a tftp server. Log_to_tftp - choose this parameter to upload log files from sim m...
Page 262
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 259 dgs-3324sri:4#upload sim_ms log_to_tftp 10.55.47.1 d:\log.Txt all command: upload sim_ms log_to_tftp 10.55.47.1 d:\log.Txt all this device is uploading log file. Please wait several minutes… upload status : id mac ad...
Page 263: Sntp
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 260 29 t ime and sntp c ommands the simple network time protocol (sntp) {an adaptation of the network time protocol (ntp)} commands in the command line interface (cli) are listed (along with the appropriate parameters) i...
Page 264
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 261 disable sntp purpose disables sntp server support. Syntax disable sntp description this will disable sntp support. Sntp service must be separately configured (see config sntp). Parameters none. Restrictions only admi...
Page 265
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 262 dgs-3324sri:4#config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 command: config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 success. Dgs-3324sri:4# show sntp purpose used to display the s...
Page 266
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 263 example usage: to manually set system time and date settings: dgs-3324sri:4#config time 30jun2003 16:30:30 command: config time 30jun2003 16:30:30 success. Dgs-3324sri:4# config time zone purpose used to determine th...
Page 267
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 264 config dst description dst can be enabled and configured using this command. When enabled this will adjust the system clock to comply with any dst requirement. Dst adjustment effects system time for both manually con...
Page 268
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 265 config dst subtract during the summertime. The possible offset times are 30, 60, 90, 120. The default value is 60. Restrictions only administrator-level users can issue this command. Example usage: to configure dayli...
Page 270
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 267 delete arpentry restrictions only administrator-level users can issue this command. Example usage: to delete an entry of ip address 10.48.74.121 from the arp table: dgs-3324sri:4#delete arpentry 10.48.74.121 command:...
Page 271
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 268 show arpentry parameters − the name of the ip interface the end node or station for which the arp table entry was made, resides on. − the network address corresponding to the ip interface name above. Static − display...
Page 272
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 269 to remove dynamic entries in the arp table: dgs-3324sri:4#clear arptable command: clear arptable success. Dgs-3324sri:4#.
Page 273: Vrrp C
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 270 31 vrrp c ommands vrrp or virtual routing redundancy protocol is a function on the switch that dynamically assigns responsibility for a virtual router to one of the vrrp routers on a lan. The vrrp router that control...
Page 274
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 271 to enable vrrp globally on the switch: dgs-3324sri:4#enable vrrp command: enable vrrp success. Dgs-3324sri:4# example usage: to enable the virtual ip address to be pinged: dgs-3324sri:4#enable vrrp ping command: enab...
Page 276
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 273 create vrrp vrid disable the critical ip address entered above. The default is disable. Restrictions only administrator-level users can issue this command. Example usage: to create a vrrp entry: dgs-3324sri:4#create ...
Page 277
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 274 config vrrp vrid parameters vrid - enter a value between 1 and 255 that uniquely identifies the vrrp group to configure. All routers participating in this group must be assigned the same vrid value. This value must b...
Page 278
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 275 dgs-3324sri:4#config vrrp vrid 1 ipif trinity state enable priority 100 advertisement_interval 2 command: config vrrp vrid 1 ipif trinity state enable priority 100 advertisement_interval 2 success. Dgs-3324sri:4# con...
Page 279
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 276 show vrrp purpose to view the vrrp settings set on the switch. Syntax show vrrp ipif vrid description this command is used to view current vrrp settings of the vrrp operations table. Parameters ipif - enter the name ...
Page 280
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 277 example usage: to delete a vrrp entry: dgs-3324sri:4#delete vrrp vrid 2 ipif trinity command: delete vrrp vrid 2 ipif trinity success. Dgs-3324sri:4#.
Page 282
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 279 create iproute default purpose used to create ip route entries to the switch’s ip routing table. Syntax create iproute default {} description this command is used to create a default static ip route entry to the swit...
Page 283
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 280 dgs-3324sri:4#delete iproute 10.48.74.121/8 10.1.1.254 command: delete iproute 10.48.74.121/8 10.1.1.254 success. Dgs-3324sri:4# delete iproute default purpose used to delete a default ip route entry from the switch’...
Page 284
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 281 dgs-3324sri:4#show iproute command: show iproute routing table ip address/netmask gateway interface cost protocol --------------- --------------- --------------- ---- ----------- 0.0.0.0 10.1.1.254 system 1 default 1...
Page 285
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 282 33 r oute r edistribution c ommands the route redistribution commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create route red...
Page 286
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 283 route source metric metric type rip 0 to 16777214 mettype 1 mettype 2 static 0 to 16777214 mettype 1 mettype 2 local 0 to 16777214 mettype 1 mettype 2 allowed metric type combinations are mettype 1 or mettype 2. The ...
Page 289
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 286 dgs-3324sri:4#config route redistribute dst ospf src rip metric 2 command: config route redistribute dst ospf src rip metric 2 success. Dgs-3324sri:4# config route redistribute dst rip src purpose used configure rout...
Page 290
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 287 dgs-3324sri:4#config route redistribute dst ospf src rip type_1 metric 2 command: config route redistribute dst ospf src rip type_1 metric 2 success. Dgs-3324sri:4# delete route redistribute purpose used to delete an...
Page 291
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 288 dgs-3324sri:4#show route redistribute command: show route redistribute source destination type metric protocol protocol -------- ------------ -------- -------- static rip all 1 local ospf type-2 20 total entries : 2 ...
Page 293
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 290 config bootp_relay add purpose used to add an ip destination address to the switch’s bootp relay table. Syntax config bootp_relay add ipif description this command adds an ip address as a destination to forward (rela...
Page 294
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 291 enable bootp_relay purpose used to enable the bootp relay function on the switch. Syntax enable bootp_relay description this command, in combination with the disable bootp_relay command below, is used to enable and d...
Page 295
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 292 show bootp_relay purpose used to display the current bootp relay configuration. Syntax show bootp_relay {ipif } description this command will display the current bootp relay configuration for the switch, or if an ip ...
Page 297
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 294 to add an entry domain name dns1, ip address 10.43.21.12 to dns static table: dgs-3324sri:4#config dnsr add static dns1 10.43.21.12 command: config dnsr add static dns1 10.43.21.12 success. Dgs-3324sri:4# example usa...
Page 298
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 295 dgs-3324sri:4#enable dnsr cache command: enable dnsr cache success. Dgs-3324sri:4# example usage: to enable static table lookup for dns relay. Dgs-3324sri:4#enable dnsr static command: enable dnsr static success. Dgs...
Page 299
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 296 dgs-3324sri:4#disable dnsr cache command: disable dnsr cache success. Dgs-3324sri:4# example usage: to disable static table lookup for dns relay. Dgs-3324sri:4#disable dnsr static command: disable dnsr static success...
Page 301
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 298 config rip rx_mode − determines how received rip packets will be interpreted – as rip versionv1 only, v2 only, orv1 or v2. This entry specifies which version of the rip protocol will be used to receive rip packets. T...
Page 302
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 299 config rip timer restrictions only administrator-level users can issue this command. Example usage: to configure the rip timers for the switch: dgs-3324sri:4#config rip timer update_interval 60 timeout_interval 60 ga...
Page 303
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 300 dgs-3324sri:4#disable rip command: disable rip success. Dgs-3324sri:4# show rip purpose used to display the rip configuration and statistics for the switch. Syntax show rip {ipif } description this command will displ...
Page 306
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 303 to disable dvmrp: dgs-3324sri:4#disable dvmrp command: disable dvmrp success. Dgs-3324sri:4# show dvmrp routing_table purpose used to display the current dvmrp routing table. Syntax show dvmrp routing table [ipaddres...
Page 307
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 304 show dvmrp neighbor parameters − the name of the ip interface for which to display the dvmrp neighbor table. Ipaddress − the ip address and netmask of the destination. The address and mask information can be specifie...
Page 308
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 305 gs-3324sri:4#show dvmrp nexthop command: show dvmrp nexthop source ip address/netmask interface name type ----------------- --------------- ------ 10.0.0.0/8 ip2 leaf 10.0.0.0/8 ip3 leaf 20.0.0.0/8 system leaf 20.0.0...
Page 309: Pim C
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 306 38 pim c ommands pim or protocol independent multicast is a method of forwarding traffic to multicast groups over the network using any pre- existing unicast routing protocol, such as rip or ospf, set on routers with...
Page 310: Pim-Dm
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 307 register and register suppression messages multicast sources do not always join the intended receiver group. The first hop router (dr) can send multicast data without being the member of a group or having a designate...
Page 312
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 309 disable pim purpose used to disable pim function on the switch. Syntax disable pim description this command will disable pim for the switch. Any previously configured pim settings will remain unchanged and may be ena...
Page 314
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 311 config pim register_suppression_time purpose used to configure the interval between the sending of register packets for the pim protocol. Syntax config pim register_suppression_time description this command is to be ...
Page 315
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 312 dgs-3324sri:4#create pim crp group 231.0.0.1/32 rp trinity command: create pim crp group 231.0.0.1/32 rp trinity success. Dgs-3324sri:4# delete pim crp purpose to disable the switch in becoming a possible candidate t...
Page 316
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 313 config pim crp means a higher priority, yet, if there is a tie for the highest priority, the router having the higher ip address will become the rp. The user may set a priority between 0 – 255 with a default setting ...
Page 317
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 314 delete pim static_rp purpose to remove the multicast group ip address used in identifying the rendezvous point (rp). Syntax delete pim static_rp group description this command will remove the multicast group ip addre...
Page 319
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 316 to configure the last hop router to never enter an spt dgs-3324sri:4#config last_hop_spt_threshold 0 command: config last_hop_spt_threshold 0 success. Dgs-3324sri:4# show pim rpset purpose used to display the rp set ...
Page 320
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 317 dgs-3324sri:4# show pim crp command: show pim crp pim candidate-rp table c-rp holdtime : 150 c-rp priority : 2 c-rp wildcard prefix count : 0 group interface --------------------- --------------------- 224.0.0.1/4 tr...
Page 321
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 318 dgs-3324sri:4#config pim cbsr ipif trinity priority 4 command: config pim cbsr ipif trinity priority 4 success. Dgs-3324sri:4# usage example: to configure the hash mask length for the cbsr: dgs-3324sri:4#config pim c...
Page 322
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 319 dgs-3324sri:4# show pim cbsr command: show pim cbsr pim candidate-bsr table c-bsr hash mask len : 30 c-bsr bootstrap period : 2 interface ip address priority --------------------- --------------------- ------------ t...
Page 324
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 321 dgs-3324sri:4# show pim ipmroute command: show pim ipmroute pim ip multicast route table ua = upstream asserttimer am = assert metric ampref = assert metricpref arb = assert rptbit group address source address ua am ...
Page 325
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 322 dgs-3324sri:4# create pim register_checksum_include_data rp_ address 11.1.1.1 command: create pim register_checksum_include_data rp_ address 11.1.1.1 success. Dgs-3324sri:4# delete pim register_checksum_include_data ...
Page 326
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 323 dgs-3324sri:4# show pim register_checksum_include_data_rp_ list command: show pim register_checksum_include_data_rp_ list rp address ------------------------------------------- 11.1.1.1 total entries: 1 dgs-3324sri:4...
Page 327: Ip M
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 324 39 ip m ulticasting c ommands the ip multicasting commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters show ipmc cache {group } {i...
Page 329: Md5 C
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 326 40 md5 c onfiguration c ommands the md5 configuration commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create md5 key config m...
Page 330
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 327 to configure an md5 key password: dgs-3324sri:4#config md5 key 1 taboo command: config md5 key 1 taboo success. Dgs-3324sri:4# delete md5 key purpose used to delete an entry in the md5 key table. Syntax delete md5 ke...
Page 331
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 328 dgs-3324sri:4#show md5 command: show md5 md5 key table configurations key-id key ------ ---------- 1 dlink 2 develop 3 fireball 4 intelligent total entries: 4 dgs-3324sri:4#.
Page 332: Ospf C
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 329 41 ospf c onfiguration c ommands the ospf configuration commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config ospf router_id...
Page 334
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 331 dgs-3324sri:4#enable ospf command: enable ospf success. Dgs-3324sri:4# disable ospf purpose used to disable ospf on the switch. Syntax disable ospf description this command, in combination with the enable ospf comman...
Page 335
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 332 to show ospf state: dgs-3324sri:4#show ospf command: show ospf ospf router id : 10.1.1.2 state : enabled ospf interface settings interface ip address area id state link metric status ------------ ------------------ -...
Page 338
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 335 dgs-3324sri:4#show ospf area command: show ospf area area id type stub import summary lsa stub default cost -------------- ------------- ------------------------------------ ------------------- 0.0.0.0 normal none no...
Page 339
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 336 usage example to delete an ospf host route: dgs-3324sri:4#delete ospf host_route 10.48.74.122 command: delete ospf host_route 10.48.74.122 success. Dgs-3324sri:4# config ospf host_route purpose used to configure ospf...
Page 340
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 337 dgs-3324sri:4#show ospf host_route command: show ospf host_route host address metric area_id --------------- --------------- ----------- 10.48.73.21 2 10.1.1.1 10.48.74.122 1 10.1.1.1 total entries: 2 dgs-3324sri:4# ...
Page 341
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 338 delete ospf aggregation parameters − a 32-bit number in the form of an ip address (xxx.Xxx.Xxx.Xxx) that uniquely identifies the ospf area in the ospf domain. − the 32-bit number in the form of an ip address that uni...
Page 342
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 339 show ospf aggregation purpose used to display the current ospf area aggregation settings. Syntax show ospf aggregation {} description this command will display the current ospf area aggregation settings. Parameters −...
Page 343
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 340 note: when this command displays a “ * ” (a star symbol) in the ospf lsdb table for the area_id or the cost, this is interpreted as “no area id” for external lsas, and as “no cost given” for the advertised link. Usag...
Page 344
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 341 show ospf virtual_neighbor purpose used to display the current ospf virtual neighbor router table. Syntax show ospf virtual_neighbor { } description this command will display the current ospf virtual neighbor router ...
Page 345
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 342 config ospf ipif parameters − the name of the ip interface. Area − a 32-bit number in the form of an ip address (xxx.Xxx.Xxx.Xxx) that uniquely identifies the ospf area in the ospf domain. Priority − the priority use...
Page 347
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 344 dgs-3324sri:4#config ospf all state enable command: config ospf all state enable success. Dgs-3324sri:4# show ospf ipif purpose used to display the current ospf interface settings for the specified interface name. Sy...
Page 348
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 345 to display the current ospf interface settings, for all ospf interfaces on the switch: dgs-3324sri:4#show ospf all command: show ospf all interface name: system ip address: 10.42.73.10/8 (link up) network medium type...
Page 349
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 346 create ospf virtual_link parameters − a 32-bit number in the form of an ip address (xxx.Xxx.Xxx.Xxx) that uniquely identifies the ospf area in the ospf domain. − the ospf router id for the remote area. This is a 32-b...
Page 350
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 347 config ospf virtual_link parameters − a 32-bit number in the form of an ip address (xxx.Xxx.Xxx.Xxx) that uniquely identifies the ospf area in the ospf domain. − the ospf router id for the remote area. This is a 32-b...
Page 351
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 348 delete ospf virtual_link parameters − a 32-bit number in the form of an ip address (xxx.Xxx.Xxx.Xxx) that uniquely identifies the ospf area in the ospf domain. − the ospf router id for the remote area. This is a 32-b...
Page 352
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 349 dgs-3324sri:4#show ospf virtual_link command: show ospf virtual_link virtual interface configuration transit virtual hello dead authentication link area id neighbor router interval interval status --------------- ---...
Page 353
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 350 42 r oute p reference c ommands route preference is a way for routers to select the best path when there are two or more different routes to the same destination from two different routing protocols. The majority of ...
Page 355
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 352 show route preference parameters local – enter this parameter to view the route preference settings for the local route. Static - enter this parameter to view the route preference settings for the static route. Rip -...
Page 356
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 353 dgs-3324sri:4# show route preference rip command: show route preference rip route preference settings route type preference ---------- ---------- rip 100 dgs-3324sri:4#.
Page 357
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 354 43 j umbo f rame c ommands certain switches can support jumbo frames (frames larger than the standard ethernet frame size of 1518 bytes). To transmit frames of up to 9k (and 9004 bytes tagged), the user can increase ...
Page 358
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 355 to enable the jumbo frame function on the switch: dgs-3324sri:4#disable jumbo_frame command: disable jumbo_frame success. Dgs-3324sri:4# show jumbo_frame purpose used to show the status of the jumbo frame function on...
Page 359
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 356 44 f ile s ystem c ommands file system commands are used to configure files stored on a storage accessory located in the switch, such as a compactflash card that can be used with the dgs-3324sri only. These commands ...
Page 360
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 357 to view the storage media accessory information: dgs-3324sri:4#show storage_media_info command: show storage_media_info ------------------------------------------------ drive media_type size label fs_type c: cf card ...
Page 361
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 358 example usage: to copy a file: dgs-3324sri:4#copy c:/abc.Cfg c:/def.Txt command: copy c:/abc.Cfg c:/def.Txt processing...100 % done!! Dgs-3324sri:4# dir purpose used to list the files and directories on the storage m...
Page 363
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 360 dgs-3324sri:4#format c: fat16 full dog command: format c: fat16 full dog formatting...100 % format media successfully!! Dgs-3324sri:4# md purpose to create a directory. Syntax md description this command is used to m...
Page 364
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 361 rd purpose used to delete a directory from the storage media accessory. Syntax rd {} description this command is used to delete a directory listed on the storage media accessory. Parameters - enter the path and name ...
Page 365
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 362 rename purpose to rename a file. Syntax rename description this command is used to rename a filename located on the storage media accessory. Parameters - enter the path and name of the file to be renamed. - enter the...
Page 366
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 363 45 c ommand h istory l ist the command history list commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters ? {} show command_history...
Page 367
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 364 dgs-3324sri:4#? .. ? Clear clear arptable clear counters clear fdb clear log config 802.1p default_priority config 802.1p user_priority config 802.1x auth_mode config 802.1x auth_parameter ports config 802.1x auth_pr...
Page 368
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 365 to display the command history: dgs-3324sri:4#show command_history command: show command_history ? ? Show show vlan config router_ports vlan2 add 1:1-1:10 config router_ports vlan2 add config router_ports vlan2 confi...
Page 369
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 366 a t echnical s pecifications physical and environmental ac input & external redundant power supply: 100 – 120; 200 - 240 vac, 50/60 hz (internal universal power supply) power consumption: dgs-3324sr/ dgs-3324sri - 90...
Page 370
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 367 general standards: ieee 802.3u 100base-tx fast ethernet ieee 802.3ab 1000base-t gigabit ethernet ieee 802.1d spanning tree ieee 802.1w rapid spanning tree ieee 802.1s multiple spanning tree ieee 802.1 p/q vlan ieee 8...
Page 371
Xstack dgs/dxs-3300 series layer 3 stackable gigabit ethernet switch cli manual 368 general number of ports: dgs-3324sri - 24 x 10/100/1000 mbps nway ports, 8 sfp ports, 6 10-gigabit staking ports dgs-3324sr - 24 x 10/100/1000 mbps nway ports, 4 sfp ports, 2 10-gigabit staking ports dxs-3326gsr – 24...