1. DL manuals
  2. D-Link
  3. Switch
  4. xStack
  5. Reference manual

D-Link xStack Reference manual

Manual is about: DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch

Summary of xStack

  • Page 1

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 239 ] mepid {period [1sec

  • Page 2: Table Of Contents

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide ii table of contents chapter 1 using the command line interface............................................................................. 1 chapter 2 basic management commands .......................................

  • Page 3

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide iii chapter 38 file system management commands .................................................................... 499 chapter 39 filter commands .......................................................................

  • Page 4

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide iv chapter 78 pim6-sm commands .............................................................................................. 905 chapter 79 policy route commands .......................................................

  • Page 5

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide v appendix b system log entries ............................................................................................... 1238 appendix c trap entries .............................................................

  • Page 6: Chapter 1

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1 chapter 1 using the command line interface the dgs-3620 layer 3 stackable gigabit ethernet switch series are members of the d-link xstack® family. Ranging from 10/100/1000mbps edge switches to core gigabit switche...

  • Page 7

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 2 1-2 setting the switch’s ip address each switch must be assigned its own ip address, which is used for communication with an snmp network manager or other tcp/ip application (for example bootp, tftp). The switch’s...

  • Page 8

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 3 dgs-3620-28sc:admin# config ipif system ipaddress 10.24.22.100/255.0.0.0 command: config ipif system ipaddress 10.24.22.100/8 success. Dgs-3620-28sc:admin# in the above example, the switch was assigned an ip addre...

  • Page 9

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 4 dgs-3620-28sc:admin#config account command: config account next possible completions: dgs-3620-28sc:admin# in this case, the command config account was entered with the parameter . The cli will then prompt to ente...

  • Page 10

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 5 dgs-3620-28sc:admin#the available commands: .. ? Cable_diag cd cfm change clear config copy create debug del delete dir disable download enable erase format install login logout md move no ping ping6 rd reboot rec...

  • Page 11

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 6 log_software_module loopback loopdetect mac_based_access_control mac_based_access_control_local mac_based_vlan mac_notification max_mcast_group mcast_filter_profile md5 mirror mld mld_proxy mld_snooping multicast ...

  • Page 13

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 8 left arrow move cursor to left. Right arrow move cursor to right tab help user to select appropriate token. The screen display pauses when the show command output reaches the end of the page. 1-5 multiple page dis...

  • Page 15

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 10 operator - specifies the name of the operator account. Power_user - specifies a power user level account. The power user level is lower than the operator level and higher than the user level. User - specifies the...

  • Page 16

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 11 2-2 enable password encryption description the user account configuration information will be stored in the configuration file, and can be applied to the system later. If the password encryption is enabled, the p...

  • Page 17

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 12 restrictions only administrator-level users can issue this command. Example to disable password encryption: dgs-3620-28sc:admin#disable password encryption command: disable password encryption success. Dgs-3620-2...

  • Page 18

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 13 success. Dgs-3620-28sc:admin# to configure the user password of the “administrator” account: dgs-3620-28sc:admin#config account administrator encrypt sha_1 *@&nwozk3ktsexuv00ywo1g5jlukkv+toyg command: config acco...

  • Page 19

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 14 format delete account parameters - enter the name of the user who will be deleted. Restrictions only administrator-level users can issue this command. One active admin user must exist. Example to delete the user ...

  • Page 20

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 15 total entries: 1 ctrl+c esc q quit space n next page p previous page r refresh 2-8 show switch description this command is used to display the switch information. Format show switch parameters none. Restrictions ...

  • Page 21

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 16 pim : disabled pim6 : disabled pim6 : disabled ospfv3 : disabled bgp : disabled vlan trunk : disabled telnet : enabled (tcp 23) web : enabled (tcp 80) snmp : disabled ssl status : disabled ssh status : disabled 8...

  • Page 22

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 17 dgs-3620-28sc:admin#show environment command: show environment internal power : active external power : fail current temperature(celsius) : 56 high warning temperature threshold(celsius) : 79 low warning temperat...

  • Page 23

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 18 2-11 config temperature threshold description this command is used to configure the warning temperature high threshold or low threshold. When temperature is above the high threshold or below the low threshold, sw...

  • Page 24

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 19 restrictions none. Example to display the console port setting: dgs-3620-28sc:admin#show serial_port command: show serial_port baud rate : 115200 data bits : 8 parity bits : none stop bits : 1 auto-logout : 10 mi...

  • Page 25

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 20 command: config serial_port baud_rate 9600 success. Dgs-3620-28sc:admin# 2-14 enable clipaging description this command is used to enable pausing of the screen display when show command output reaches the end of ...

  • Page 26

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 21 restrictions only administrator and operator-level users can issue this command. Example to disable pausing of the screen display when show command output reaches the end of the page: dgs-3620-28sc:admin#disable ...

  • Page 27

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 22 format disable telnet parameters none. Restrictions only administrator and operator-level users can issue this command. Example to disable telnet: dgs-3620-28sc:admin#disable telnet command: disable telnet succes...

  • Page 28

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 23 dgs-3620-28sc:admin# 2-19 disable web description this command is used to disable web ui. Format disable web parameters none. Restrictions only administrator and operator-level users can issue this command. Examp...

  • Page 29

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 24 restrictions only administrator and operator-level users can issue this command. Example to save the current configuration to the bootup configuration file: dgs-3620-28sc:admin#save command: save saving all confi...

  • Page 30

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 25 parameters force_agree –(optional) specify to immediately execute the reboot command without further confirmation. Restrictions only administrator-level users can issue this command. Example to restart the switch...

  • Page 31

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 26 are you sure to proceed with system reset except ip address?(y/n) success. Dgs-3620-28sc:admin# to reset the system configuration settings: dgs-3620-28sc:admin#reset config command: reset config are you sure to p...

  • Page 32

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 27 2-24 logout description this command is used to log out of the switch. Format logout parameters none. Restrictions none. Example to logout of the switch: dgs-3620-28sc:admin#logout command: logout *********** * l...

  • Page 33

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 28 restrictions none. Example to clear the terminal screan: dgs-3620-28sc:admin#clear command: clear 2-26 config terminal width description this command is used to configure the terminal width. Format config termina...

  • Page 34

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 29 format show terminal width parameters none. Restrictions none. Example to display the configuration of the current terminal width: dgs-3620-28sc:admin#show terminal width command: show terminal width global termi...

  • Page 35

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 30 dgs-3620-28sc:admin# show device_status command: show device_status unit 1: internal power: active external power: fail left fan : 1, 3 fail right fan : 2 fail back fan : ok cpu fan : fail unit 2: internal power:...

  • Page 37

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 32 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to enable the 802.1x function: dgs-3620-28sc:admin#enable 802.1x command: enable 802.1x succes...

  • Page 38

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 33 3-3 create 802.1x user description this command is used to create an 802.1x user. Format create 802.1x user parameters - enter to add a user name. Restrictions only administrator, operator and power-user level us...

  • Page 39

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 34 example to delete the user named “tiberius”: dgs-3620-28sc:admin#delete 802.1x user tiberius command: delete 802.1x user tiberius success. Dgs-3620-28sc:admin# 3-5 show 802.1x user description this command is use...

  • Page 41

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 36 authentication protocol : radius_eap forward eapol pdu : disabled max user : 448 radius authorization : enabled dgs-3620-28sc:admin# to display the 802.1x state for ports 1 to 5: dgs-3620-28sc:admin# show 802.1x ...

  • Page 43

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 38 restrictions only administrator, operator and power-user level users can issue this command. Example to configure the 802.1x pdu forwarding state on ports 1 to 2: dgs-3620-28sc:admin#config 802.1x fwd_pdu ports 1...

  • Page 45

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 40 example to configure the parameters that control the operation of the authenticator associated with a port: dgs-3620-28sc:admin# config 802.1x auth_parameter ports 1-20 direction both command: config 802.1x auth_...

  • Page 47

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 42 dgs-3620-28sc:admin# config 802.1x max_users 2 command: config 802.1x max_users 2 success. Dgs-3620-28sc:admin# 3-15 config 802.1x reauth description this command is used to reauthenticate the device connected wi...

  • Page 48

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 43 format create 802.1x guest_vlan parameters - enter the static vlan to be a guest vlan. Restrictions only administrator, operator and power-user level users can issue this command. Example to assign a static vlan ...

  • Page 50

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 45 restrictions none. Example to display guest vlan information: dgs-3620-28sc:admin#show 802.1x guest_vlan command: show 802.1x guest_vlan guest vlan setting --------------------------------------------------------...

  • Page 51

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 46 - the re-transmit value must be between 1 and 20. Restrictions only administrator, operator and power-user level users can issue this command. Example to add a new radius server: dgs-3620-28sc:admin#config radius...

  • Page 53

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 48 3-23 show radius description this command is used to display radius server configurations. Format show radius parameters none. Restrictions none. Example to display radius server configurations: dgs-3620-28sc:adm...

  • Page 54

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 49 restrictions none. Example to display authenticator statistics information for port 3: dgs-3620-28sc:admin# show auth_statistics ports 3 command: show auth_statistics ports 3 auth vid :100 mac address :00-00-00-0...

  • Page 55

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 50 dgs-3620-28sc:admin# show auth_diagnostics ports 3 command: show auth_diagnostics ports 3 auth vid 100 mac address 00-00-00-00-00-03 port number : 1 entersconnecting 20 eaplogoffswhileconnecting 0 entersauthentic...

  • Page 56

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 51 command: show auth_session_statistics ports 3 auth vid : 100 mac address : 00-00-00-00-00-03 port number : 3 sessionoctetsrx 0 sessionoctetstx 0 sessionframesrx 0 sessionframestx 0 sessionid sessionauthenticmetho...

  • Page 57

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 52 radiusauthclientserverportnumber x radiusauthclientroundtriptime 0 radiusauthclientaccessrequests 0 radiusauthclientaccessretransmissions 0 radiusauthclientaccessaccepts 0 radiusauthclientaccessrejects 0 radiusau...

  • Page 58

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 53 radiusauthclientaccesschallenges 0 radiusauthclientmalformedaccessresponses 0 radiusauthclientbadauthenticators 0 radiusauthclientpendingrequests 0 radiusauthclienttimeouts 0 radiusauthclientunknowntypes 0 radius...

  • Page 59

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 54 radiusaccclienttimeouts 0 radiusaccclientunknowntypes 0 radiusaccclientpacketsdropped 0 radiusacctclient ==> radiusacctclientinvalidserveraddresses 0 radiusacctclientidentifier d-link radiusauthserverentry ==> ra...

  • Page 60: Chapter 4

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 55 chapter 4 access authentication control (aac) commands enable authen_policy disable authen_policy show authen_policy enable authen_policy_encryption disable authen_policy_encryption create authen_login method_lis...

  • Page 62

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 57 the switch also supports the radius protocol for authentication using the access authentication control commands. Radius or remote authentication dial in user server also uses a remote server for authentication a...

  • Page 63

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 58 enable authentication mothod list to authenticate the enable password for promoting the user‘s privilege to administrator level. Format enable authen_policy parameters none. Restrictions only administrator-level ...

  • Page 64

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 59 dgs-3620-28sc:admin#disable authen_policy command: disable authen_policy success. Dgs-3620-28sc:admin# 4-3 show authen_policy description this command is used to display whether system access authentication polic...

  • Page 65

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 60 restrictions only administrator-level users can issue this command. Example to enable the authentication policy encryption: dgs-3620-28sc:admin#enable authen_policy_encryption command: enable authen_policy_encryp...

  • Page 66

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 61 format create authen_login method_list_name parameters - enter the user-defined method list name. Restrictions only administrator-level users can issue this command. Example to create a user-defined method list f...

  • Page 67

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 62 name can be up to 15 characters long. Method - choose the desired authentication method: tacacs - specifies authentication by the built-in server group tacacs. Xtacacs - specifies authentication by the built-in s...

  • Page 69

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 64 parameters - enter the user-defined method list name. Restrictions only administrator-level users can issue this command. Example to create a user-defined method list for promoting a user's privilege to admin lev...

  • Page 70

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 65 - enter authentication by the user-defined server group. The server group value can be up to 15 characters long. Local_enable - specifies authentication by local enable password in the device. None - specifies no...

  • Page 73

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 68 example to display the login and enable method list for all applications: dgs-3620-28sc:admin#show authen application command: show authen application application login method list enable method list ----------- ...

  • Page 74

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 69 4-17 config authen server_group description this command is used to add or remove an authentication server host to or from the specified server group. Built-in server group tacacs, xtacacs, tacacs+, and radius ac...

  • Page 75

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 70 format delete authen server_group parameters - enter the user-defined server group name. Restrictions only administrator-level users can issue this command. Example to delete a user-defined authentication server ...

  • Page 76

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 71 radius 10.1.1.224 radius tacacs 10.1.1.225 tacacs tacacs+ 10.1.1.226 tacacs+ xtacacs 10.1.1.227 xtacacs total entries : 5 dgs-3620-28sc:admin# 4-20 create authen server_host description this command is used to cr...

  • Page 77

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 72 restrictions only administrator-level users can issue this command. Example to create a tacacs+ authentication server host with a listening port number of 15555 and a timeout value of 10 seconds: dgs-3620-28sc:ad...

  • Page 78

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 73 seconds. - enter the time in seconds for waiting for a server reply. The default value is 5 seconds. The timeout value must be between 1 and 255 seconds. Retransmit - specifies the count for re-transmit. This val...

  • Page 79

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 74 success. Dgs-3620-28sc:admin# 4-23 show authen server_host description this command is used to display authentication server hosts. Format show authen server_host parameters none. Restrictions only administrator-...

  • Page 80

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 75 is no time out. The default value is 30 seconds. Restrictions only administrator-level users can issue this command. Example to configure 60 seconds for user to input: dgs-3620-28sc:admin#config authen parameter ...

  • Page 81

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 76 4-26 show authen parameter description this command is used to display the authentication parameters. Format show authen parameter parameters none. Restrictions only administrator-level users can issue this comma...

  • Page 82

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 77 restrictions none. Example to enable administrator lever privilege: dgs-3620-28sc:admin# enable admin password:******** dgs-3620-28sc:admin# 4-28 config admin local_enable description this command is used to conf...

  • Page 83

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 78 4-29 create aaa server_group description this command is used to create a group of user-defined aaa servers. The maximum number of supported server groups, including the built-in server groups, is 8. Each group c...

  • Page 84

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 79 add - add a server host to the server group. Delete - remove a server host to the server group. Server_host - specifies the server host. - enter the ip address of the server host. Protocol - specifies the server ...

  • Page 85

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 80 dgs-3620-28sc:admin#delete aaa server_group mix_1 command: delete aaa server_group mix_1 success. Dgs-3620-28sc:admin# 4-32 delete aaa server_host description this command is used to delete an aaa server host. Fo...

  • Page 86

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 81 parameters none. Restrictions none. Example to display aaa global configuration: dgs-3620-28sc:admin#show aaa command: show aaa authentication policy: enabled accounting network service state: aaa method accounti...

  • Page 87

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 82 dgs-3620-28sc:admin#show aaa server_group command: show aaa server_group group name ip address protocol --------------- --------------------------------------- -------- mix_1 -------------------------------------...

  • Page 88

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 83 4-36 enable aaa_server_password_encryption description this command is used to enable aaa server password encryption. Format enable aaa_server_password_encryption parameters none. Restrictions only administrator ...

  • Page 89

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 84 dgs-3620-28sc:admin#disable aaa_server_password_encryption command: disable aaa_server_password_encryption success. Dgs-3620-28sc:admin# 4-38 config accounting description this command is used to configure a user...

  • Page 92

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 87 restrictions only administrator level users can issue this command. Example to create a user-defined accounting method list called “shell_acct”: dgs-3620-28sc:admin#create accounting method_list_name shell_acct c...

  • Page 94

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 89 accounting state ------------------- network : disabled shell : disabled system : disabled dgs-3620-28sc:admin# 4-45 create radius server_host description this command is used to create an radius server host. For...

  • Page 95

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 90 dgs-3620-28sc:admin#create radius server_host 10.1.1.222 auth_port 15555 timeout 10 command: create radius server_host 10.1.1.222 auth_port 15555 timeout 10 key is empty for tacacs+ or radius. Success. Dgs-3620-2...

  • Page 97

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 92 example to display specified source interface for all outgoing radius packets. Dgs-3620-28sc:admin#show radius source_ipif command: show radius source_ipif ip interface : if_v200 ipv4 address : none ipv6 address ...

  • Page 99

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 94 algorithm is based on des. - etner the string with maximum 344 characters. Timeout - (optional) specify the time in second to wait for the server to reply. - enter the value between 1 and 255. The default value i...

  • Page 100

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 95 dgs-3620-28sc:admin#config tacacs+ server_host 10.1.1.211 key "abcd123" command: config tacacs+ server_host 10.1.1.211 key "abcd123" success. Dgs-3620-28sc:admin# 4-53 create xtacacs server_host description this ...

  • Page 101

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 96 parameters - enter the ip address of the server host. Port - (optional) the port number of the xtacacs server host. - enter the value between 1 and 65535. The default value is 49. Timeout - (optional) specify the...

  • Page 102

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 97 dgs-3620-28sc:admin#config tacacs source_ipif if_v200 command: config tacacs source_ipif if_v200 success. Dgs-3620-28sc:admin# 4-56 show tacacs source_ipif description this command is used to display the specifie...

  • Page 106

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 101 packet_content_mask - a maximum of six offsets can be specified. Each offset defines one byte of data which is identified as a single udf field. The offset reference is also configurable. It can be defined to st...

  • Page 107

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 102 dgs-3620-28sc:admin# dgs-3620-28sc:admin#create access_profile profile_id 2 profile_name 2 ip vlan source_ip_mask 255.255.255.255 destination_ip_mask 255.255.255.0 dscp icmp command: create access_profile profil...

  • Page 109

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 104 ip - specifies an ip access control list rule. Vlan - specifies the vlan name. -specify the vlan name. The maximum length is 32 characters. Vlanid - specifies the vlan id. - enter the vlan id between 1 and 4094....

  • Page 110

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 105 offset_chunk_1 - specifies the contents of the offset trunk 1 to be monitored. - enter the contents of the offset trunk 1 to be monitored here. Mask - specifies an additional mask for each field. - enter the add...

  • Page 111

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 106 to all ports and packets must belong to the configured vlan. It can be specified by vlan name or vlan id. Vlan - specifies the vlan name. - enter the vlan name. The maximum length is 32 characters. Vlan_id - spe...

  • Page 113

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 108 permit urpf state check: enabled (replaced)priority : 7 replace tos precedence : 7 ============================================================================== =================================================...

  • Page 114

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 109 mask on class flow label tcp available hw entries : 255 ------------------------------------------------------------------------------ rule id : 1 ports: 1 match on class : 255 flow label : 0xfffff tcp action: p...

  • Page 115

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 110 permit urpf state check: enabled (replaced)priority : 7 replace tos precedence : 7 ============================================================================== dgs-3620-28sc:admin# 5-5 config time_range descri...

  • Page 116

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 111 5-6 show time_range description this command is used to display current time range settings. Format show time_range parameters none. Restrictions none. Example to display current time range setting: dgs-3620-28s...

  • Page 117

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 112 restrictions none. Example to display the acl part of the current configuration: dgs-3620-28sc:admin#show current_config access_profile command: show current_config access_profile #------------------------------...

  • Page 118

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 113 parameters profile_id - specifies the index of the access list profile. - enter the value between 1 and 5. All - specifies to delete all the access list profiles. Restrictions only administrator, operator and po...

  • Page 119

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 114 ip - specifies an ip cpu access control list rule. Vlan - specifies a vlan mask. Source_ip_mask - specifies an ip source submask. - enter an ip source submask. Destination_ip_mask - specifies an ip destination s...

  • Page 120

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 115 ipv6 - specifies the ipv6 mask. Class - specifies the ipv6 class mask. Flowlabel - specifies the ipv6 flow label mask. Source_ipv6_mask - specifies the ipv6 source ip mask. - enter the ipv6 source ip mask. Desti...

  • Page 122

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 117 - enter the value between 0 and 65535. Protocol_id - specifies that the rule will apply to the value of ip protocol id traffic. - enter the value between 0 and 255. User_define - (optional) specify that the rule...

  • Page 123

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 118 example to configure access list entry: dgs-3620-28sc:admin#config cpu access_profile profile_id 1 add access_id 1 ethernet vlan default port 1-3 deny command: config cpu access_profile profile_id 1 add access_i...

  • Page 124

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 119 unused rule entries: 99 ------------------------------------------------------------------------------ rule id : 1 ports: 1 match on vlan id : 1 802.1p : 7 ethernet type : 0xffff action: permit =================...

  • Page 125

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 120 class : 255 flow label : 0xfffff action: permit ============================================================================== ============================================================================== profi...

  • Page 126

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 121 restrictions only administrator, operator and power-user level users can issue this command. Example to enable cpu interface filtering: dgs-3620-28sc:admin#enable cpu_interface_filtering command: enable cpu_inte...

  • Page 127

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 122 depending on the user configuration. For single rate three color mode, users need to specify the committed rate, in kbps, the committed burst size, and the excess burst size. For the two rate three color mode, u...

  • Page 128

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 123 pbs - (optional) specify the peak burst size. The unit is kbyte. - enter the value between 0 and 131072. Color_blind - specifies the meter mode as color-blind. The default is color-blind mode. Color_aware - spec...

  • Page 129

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 124 disable - disable the packet counter for the specified acl entry in the green flow. Exceed - this field denotes the yellow packet flow. Yellow packet flows may have excess packets permitted through or dropped. U...

  • Page 133

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 128 src_port_mask - specifies the tcp source port mask. - enter the tcp source port mask value here. Dst_port_mask - specifies the tcp destination port mask. - enter the tcp source port mask value here. Flag_mask - ...

  • Page 136

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 131 mask - specifies the destination ip address used here. - enter the destination network mask here. Dscp - (optional) specifies the value of dscp. The dscp value ranges from 0 to 63. - enter the dscp value used he...

  • Page 137

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 132 - enter the ipv6 source address mask value here. Destination_ipv6 - (optional) specifies the value of ipv6 destination address. - enter the source ipv6 destination address here. Mask - specifies the ipv6 destina...

  • Page 138

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 133 the “counter” is overridden. Enable - specifies that the acl counter feature will be enabled. Disable - specifies that the acl counter feature will be disabled. Deny - specifies the packets that match the egress...

  • Page 139

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 134 parameters profile_id - (optional) specifies the index of the egress access list profile. - enter the profile id here. This value must be between 1 and 4. Profile_name - (optional) specifies the name of the prof...

  • Page 140

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 135 destination ip : 255.255.255.255 dscp available hardware entries : 126 ------------------------------------------------------------------------------- - rule id : 1 (auto assign) port group: 1 match on source ip...

  • Page 141

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 136 dgs-3620-28sc:admin# show egress_access_profile profile_id 1 command: show egress_access_profile profile_id 1 egress access profile table =========================================================================...

  • Page 142

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 137 dgs-3620-28sc:admin# show current_config egress_access_profile command: show current_config egress_access_profile #------------------------------------------------------------------------------ - # egress acl cr...

  • Page 143

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 138 - enter the profile id used here. This value must be between 1 and 4. Profile_name - specifies the name of the profile. - enter the profile name used here. This name can be up to 32 characters long. Access_id - ...

  • Page 144

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 139 permit - permit the packet. Replace_dscp - (optional) changes the dscp of the packet. - enter the dscp replace value here. This value must be between 0 and 63. Drop - drops the packet. Counter - (optional) speci...

  • Page 145

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 140 example to configure a “two rates three color” flow meter: dgs-3620-28sc:admin# config egress_flow_meter profile_id 1 access_id 1 tr_tcm cir 1000 cbs 200 pir 2000 pbs 200 exceed replace_dscp 21 violate drop comm...

  • Page 146

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 141 dgs-3620-28sc:admin# show egress_flow_meter command: show egress_flow_meter flow meter information: ------------------------ profile id : 1 access id : 1 mode : trtcm / color-blind cir:1000(kbps) cbs:2000(kbyte)...

  • Page 147

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 142 dgs-3620-28sc:admin# create port_group id 2 name group2 command: create port_group id 2 name group2 success. Dgs-3620-28sc:admin# 6-9 config port_group description this command is used to add or delete a port li...

  • Page 148

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 143 parameters id - specifies the port group id. - enter the port group id used here. This value must be between 1 and 64. Name - specifies the port group name. - enter the port group name here. This name can be up ...

  • Page 149

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 144 dgs-3620-28sc:admin# show port_group command: show port_group port group table group id group name ports 1 group1 1-2,5 2 group2 4,5,7,9,11,13 15,17,19-25 4 group3 5-7 total entries :3 dgs-3620-28sc:admin#.

  • Page 152

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 147 dgs-3620-28sc:admin# 7-4 config arp_aging time description this command is used to set the maximum amount of time, in minutes, that an arp entry can remain in the switch’s arp table, without being accessed, befo...

  • Page 153

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 148 static - displays the static entries to the arp table. Mac_address - displays the arp entry by mac address. - enter the mac address. Note: if no parameter is specified, all arp entries will be displayed. Restric...

  • Page 154

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 149 dgs-3620-28sc:admin#clear arptable command: clear arptable success. Dgs-3620-28sc:admin# 7-7 show ipfdb description this command is used to display the ip address forwarding table on the switch. Format show ipfd...

  • Page 156

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 151 8-2 show arp_spoofing_prevention description this command is used to display the arp spoofing prevention status. Format show arp_spoofing_prevention parameters none. Restrictions none. Example to display the arp...

  • Page 157: Chapter 9

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 152 chapter 9 asymmetric vlan commands enable asymmetric_vlan disable asymmetric_vlan show asymmetric_vlan 9-1 enable asymmetric_vlan description this command is used to enable the asymmetric vlan function.. Format ...

  • Page 158

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 153 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable asymmetric vlan setting: dgs-3620-28sc:admin# disable asymmetric_vlan command: dis...

  • Page 159: Chapter 10

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 154 chapter 10 auto configuration commands show autoconfig enable autoconfig disable autoconfig 10-1 show autoconfig description this command is used to display the status of automatically getting configuration from...

  • Page 160

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 155 format enable autoconfig parameters none. Restrictions only administrator and operator-level users can issue this command. Example to enable dhcp auto configuration status: dgs-3620-28sc:admin#enable autoconfig ...

  • Page 161

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 156 dgs-3620-28sc:admin#.

  • Page 163

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 158 vlan - (optional) the name of the vlan corresponding to the ip interface. - enter the vlan name. The maximum length is 32 characters. State - enable or disable the ip interface. Enable - enable the ip interface....

  • Page 164

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 159 command: config ipif system vlan v1 success. Dgs-3620-28sc:admin# 11-2 create ipif description this command is used to create an l3 interface. This interface can be configured with ipv4 or ipv6 addresses. Curren...

  • Page 165

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 160 command: create ipif petrovic1 100.1.1.2/16 vlan598 success. Dgs-3620-28sc:admin# 11-3 delete ipif description this command is used to delete an interface or an ipv6 address. Format delete ipif [ {ipv6address {p...

  • Page 166

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 161 parameters - the name of the interface. All - all of the ip interfaces. Restrictions only administrator, operator and power-user level users can issue this command. Example to enable the state for interface petr...

  • Page 167

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 162 11-6 show ipif description this command is used to display ip interface settings. Format show ipif {} parameters - (optional) the name of the interface. Restrictions none. Example to display ip interface setting...

  • Page 169

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 164 example to display the configuration of out-of-band management interfaces: dgs-3620-28sc:admin#show out_band_ipif command: show out_band_ipif status : enable ip address : 192.168.0.1 subnet mask : 255.255.255.0 ...

  • Page 170

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 165 11-10 disable ipif_ipv6_link_local_auto description this command is used to disable the auto configuration of link local address when no ipv6 address is explicitly configured. Format disable ipif_ipv6_link_local...

  • Page 171

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 166 dgs-3620-28sc:admin#show ipif_ipv6_link_local_auto command: show ipif_ipv6_link_local_auto ipif: system automatic link local address: disabled dgs-3620-28sc:admin#.

  • Page 173

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 168 dgs-3620-28sc:admin#config ddm log enable command: config ddm log enable success. Dgs-3620-28sc:admin# to configure ddm trap state to enable: dgs-3620-28sc:admin#config ddm trap enable command: config ddm trap e...

  • Page 174

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 169 parameter rises above this value, the action associated with the alarm is taken. - enter the high threshold alarm value used here. Low_alarm - (optional) specify the low threshold for the alarm. When the operati...

  • Page 175

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 170 restrictions only administrator, and operator level users can issue this command. Example to configure the port 21’s temperature threshold: dgs-3620-28sc:admin#config ddm ports 1:21 temperature_threshold high_al...

  • Page 176

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 171 dgs-3620-28sc:admin#config ddm ports 1:21 rx_power_threshold high_alarm 4.55 low_alarm 0.01 high_warning 3.5 low_warning 0.03 command: config ddm ports 1:21 rx_power_threshold high_alarm 4.55 low_alarm 0.01 high...

  • Page 177

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 172 12-4 show ddm ports description this command is used to show the current operating ddm parameters and configuration values of the optic module of the specified ports. There are two types of thresholds: the admin...

  • Page 178

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 173 dgs-3620-28sc:admin#show ddm ports 1:21 configuration command: show ddm ports 1:21 configuration port: 1:21 -------------------------------------------- ddm state : enabled shutdown : alarm threshold temperature...

  • Page 181

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 176 restrictions only administrator, operator and power-user level users can issue this command. (ei mode only command) example to enable bgp protocol: dgs-3620-28sc:admin# enable bgp command: enable bgp success. Dg...

  • Page 182

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 177 13-3 create bgp description this command is used to create a bgp process. It’s as number must be set. When bgp protocol starts, it must belong to a single as. The user must set the as number before configuring a...

  • Page 183

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 178 restrictions only administrator, operator and power-user level users can issue this command. (ei mode only command) example to create a bgp process: dgs-3620-28sc:admin# delete bgp 100 command: delete bgp 100 su...

  • Page 184

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 179 example to configure the bgp process’s router id: dgs-3620-28sc:admin# config bgp router_id 10.10.10.1 command: config bgp router_id 10.10.10.1 success dgs-3620-28sc:admin# 13-6 config bgp synchronization descri...

  • Page 185

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 180 when the setting is enabled, any updates received from an external neighbor, that does not have the neighbor’s configured autonomous system (as) at the beginning of the as_path in the received update, will be de...

  • Page 187

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 182 dgs-3620-28sc:admin# delete bgp aggregate_address 10.0.0.0/8 command: delete bgp aggregate_address 10.0.0.0/8 success. Dgs-3620-28sc:admin# 13-10 show bgp aggregate_address description this command is used to sh...

  • Page 188

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 183 parameters - represents the local network that bgp will advertise. Route_map - (optional) specifies the route map to be applied to the advertised networks. If not specified, all networks are advertised. - enter ...

  • Page 189

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 184 dgs-3620-28sc:admin# config bgp network 10.108.0.0/16 clear_routemap command: config bgp network 10.108.0.0/16 clear_routemap success. Dgs-3620-28sc:admin# 13-13 delete bgp network description this command is us...

  • Page 190

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 185 restrictions none. (ei mode only command) example to show network 10.108.0.0/16 advertised in the bgp updates: dgs-3620-28sc:admin# show bgp network 10.108.0.0/16 command: show bgp network 10.108.0.0/16 network ...

  • Page 191

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 186 example this command is used to configure the bgp hold and keepalive timer: dgs-3620-28sc:admin# config bgp timer holdtime 360 keepalive 120 command: config bgp timer holdtime 360 keepalive 120 success. Dgs-3620...

  • Page 193

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 188 example this command shows how to disable the comparison of the multi exit discriminator (med): dgs-3620-28sc:admin# config bgp always_compare_med disable command: config bgp always_compare_med disable success. ...

  • Page 194

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 189 disable - specifies that the bgp dampening function's state will be disabled. Half_life - (optional) specifies the time (in minute) after which the penalty of the reachable routes will be down, by half. The defa...

  • Page 195

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 190 ip address/netmask gateway metric locprf weight path *> 20.0.0.0/8 0.0.0.0 0 32768 i *> 221.221.2.0/24 0.0.0.0 0 32768 i *d 221.221.252.0/24 1.1.1.2 1 40 i *d 221.221.253.0/24 1.1.1.2 1 40 i total entries: 4 dgs...

  • Page 196

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 191 13-19 config bgp peer_group description this command is used to configure the bgp peer group. The purpose of the neighbor peer group is to simplify the bgp neighbor configuration. The command is used to add an i...

  • Page 197

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 192 remote_as - the number of autonomous systems to which the peer group belongs to. - enter the remote as value here. This value must be between 0 and 4294967295. Add - specifies to add an ip address. Delete - spec...

  • Page 198

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 193 remote_as - the number of autonomous systems to which the neighbor belongs. - enter the remote as number here. This value must be between 1 and 4294967295. Peer_group - specifies the peer group to be created and...

  • Page 199

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 194 dgs-3620-28sc:admin# delete bgp neighbor 10.10.10.2 command: delete bgp neighbor 10.10.10.2 success. Dgs-3620-28sc:admin# 13-22 config bgp neighbor description this command is used to configure the bgp neighbor’...

  • Page 200

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 195 13-23 config bgp neighbor session description the command is used to configure the state or neighbor’s session activity for a bgp neighbor. If a neighbor is specified to be in the disabled state, it is equivalen...

  • Page 201

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 196 13-24 config bgp neighbor general description this command is used to configure the bgp neighbor’s general setting. Ebgp_multihop: this specifies the ttl of the bgp packet sent to the neighbor. If it is specifie...

  • Page 202

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 197 characters long. Ebgp_multihop - (optional) specifies the ttl of bgp packet sent to the neighbor. For an ebgp neighbor the default setting is 1. This means only direct connected neighbors are allowed. - enter th...

  • Page 203

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 198 dgs-3620-28sc:admin# config bgp neighbor general 10.100.200.1 ebgp_multihop 2 command: config bgp neighbor general 10.100.200.1 ebgp_multihop 2 success. Dgs-3620-28sc:admin# 13-25 config bgp neighbor timer descr...

  • Page 204

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 199 default - specifies that the default as original interval value will be used. Connect - (optional) minimum interval bgp sends tcp connect requests to the peer after a tcp connection fail happens. The default set...

  • Page 205

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 200 characters long. State - the specified neighbor will become the router reflector client. By default, this state is disabled. Enable - specifies that the neighbor will become the router reflector client. Disable ...

  • Page 206

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 201 out - specifies the outgoing routes sent to the peer. Add - specifies that a route map will be added. Delete - specifies that a route map will be deleted. - enter the unsurpress map name here. This name can be u...

  • Page 207

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 202 add - specifies that a filter list will be added. Delete - specifies that a filter list will be deleted. - enter the filter list name here. This name can be up to 16 characters long. Prefix_list - (optional) spe...

  • Page 208

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 203 restrictions none. (ei mode only command) example show the information of the bgp peer group local1: dgs-3620-28sc:admin# create bgp neighbor peer_group local1 command: create bgp neighbor peer_group local1 succ...

  • Page 209

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 204 dgs-3620-28sc:admin# 13-30 config bgp route_reflector cluster_id description this command is used to configure the bgp process’s global attribute. The route reflector and its clients together form a cluster. Whe...

  • Page 210

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 205 13-31 config bgp client_to_client_reflection description this command is used to configure the bgp client to client reflection setting. If the reflection is disabled, then the router will not reflect routes from...

  • Page 211

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 206 parameters - autonomous system numbers which we use to specify a bgp confederation. If it is set to zero, the bgp confederation number is deleted. By default, this setting is zero. This value must be between 0 a...

  • Page 212

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 207 dgs-3620-28sc:admin# config bgp confederation peers add 50000, 50001 command: config bgp confederation peers add 50000, 50001 success. Dgs-3620-28sc:admin# 13-34 clear bgp description this command is used to ini...

  • Page 213

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 208 dgs-3620-28sc:admin# clear bgp all command: clear bgp all success. Dgs-3620-28sc:admin# 13-35 clear bgp dampening description this command clears the route dampening information stored in the routing table. If n...

  • Page 214

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 209 parameters access_list - specifies the as path access list name. - enter the as path access list name here. This name can be up to 16 characters long. Restrictions only administrator, operator and power-user lev...

  • Page 216

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 211 13-39 show bgp as_path access_list description this command displays the autonomous system path’s access list. If a specific access list is not specified, all as path access lists will be displayed. Format show ...

  • Page 217

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 212 be up to 16 characters long. Restrictions only administrator, operator and power-user level users can issue this command. (ei mode only command) example to create a standard bgp community list: dgs-3620-28sc:adm...

  • Page 218

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 213 be sent to peers in another sub as in the same confederation and to the external peers. No_advertise - routes with this community will not be advertised to any peer either internal or external. No_export - (opti...

  • Page 219

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 214 parameters list_name - specifies the name of the community list to be deleted. - enter the community list name here. This name can be up to 16 characters long. All - specifies that all the community lists will b...

  • Page 220

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 215 dgs-3620-28sc:admin# create bgp community_list standard list1 command: create bgp community_list standard list1 success. Dgs-3620-28sc:admin# config bgp community_list standard list1 add community_set 50000:10 p...

  • Page 221

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 216 no_advertise - (optional) do not advertise to any peer (well-known community). No_export - (optional) do not export to next as (well-known community). Internet - (optional) send to the internet (well-known commu...

  • Page 222

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 217 dgs-3620-28sc:admin# show bgp route community_list communitylist command: show bgp route community_list ommunitylist bgp local router id is 192.168.32.1 status codes: s suppressed, d damped, h history, * valid, ...

  • Page 223

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 218 dgs-3620-28sc:admin# show bgp route inconsistent_as command: show bgp route inconsistent_as bgp local router id is 172.16.72.24 status codes: s suppressed, d damped, h history, * valid, > best, i - internal orig...

  • Page 224

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 219 advertised_routes - (optional) displays the routes advertised to a bgp neighbor. Received_routes - (optional) displays the routes received from this neighbor. Routes - (optional) displays routes in the routing t...

  • Page 225

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 220 bgp local router id is 172.16.232.181 status codes: s suppressed, d damped, h history, * valid, > best, i - internal origin codes: i - igp, e - egp, ? - incomplete ip address/netmask gateway metric locprf weight...

  • Page 226

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 221 13-46 show bgp dampened_routes description this command is used to display dampened entries in the border gateway protocol (bgp) routing table. Format show bgp dampened_routes parameters none. Restrictions none....

  • Page 227

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 222 restrictions none. (ei mode only command) example to show flap bgproutes information: dgs-3620-28sc:admin# show bgp flap_statistics command:show bgp flap_statistics bgp local router id is 172.29.232.182 status c...

  • Page 228

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 223 synchronization : enabled enforce first as : enabled local as number : 100 scan time : 60 hold time : 300 seconds keepalive interval : 100 seconds dampening : enabled always compare med : disabled deterministics...

  • Page 229

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 224 restrictions none. (ei mode only command) example this example displays the bgp reflection setting: dgs-3620-28sc:admin# show bgp reflection command: show bgp reflection client to client reflection state : disab...

  • Page 230

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 225 dgs-3620-28sc:admin# show bgp confederation command: show bgp confederation bgp as number : 65501 confederation identifier : 10 confederation peer : 65502,65503 neighbor list: ip address remote as number -------...

  • Page 231

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 226 13-52 show bgp trap_state description this command is used to show the bgp trap state. Format show bgp trap_state parameters none. Restrictions none. (ei mode only command) example this example displays the bgp ...

  • Page 232

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 227 example this example configures the bgp scan timer to 30 seconds: dgs-3620-28sc:admin# config bgp scan_timer 30 command: config bgp scan_timer 30 success. Dgs-3620-28sc:admin# 13-54 config bgp aggregate_next_hop...

  • Page 233

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 228 parameters enable - to enable bgp fast external fallover flag. Default is enabled. Disable - to disable bgp fast external fallover. Restrictions only administrator, operator and power-user level users can issue ...

  • Page 234

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 229 example this example sets the maximum number of prefixes that will be accepted from the neighbor 192.168.1.1 to 5000, when 50 percent of the maximum prefix limit has been reached. This will display a warning mes...

  • Page 236

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 231 dgs-3620-28sc:admin#config bpdu_protection ports 1 state enable mode drop command: config bpdu_protection ports 1 state enable mode drop success. Dgs-3620-28sc:admin# 14-2 config bpdu_protection recovery_timer d...

  • Page 237

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 232 parameters trap - specifies the trap state. Log - specifies the log state. None - specifies neither attack_detected nor attack_cleared is trapped or logged. Attack_detected - specifies events will be logged or t...

  • Page 238

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 233 14-5 disable bpdu_protection description this command is used to disable bpdu protection globally for the entire switch. Format disable bpdu_protection parameters none. Restrictions only administrator, operator ...

  • Page 239

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 234 example to display bpdu protection information for the entire switch: dgs-3620-28sc:admin#show bpdu_protection command: show bpdu_protection bpdu protection global settings --------------------------------------...

  • Page 241

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 236 • between 50m and 80m (50m~80m) • between 80m and 100m (80m~100m) • greater than 100m (>100m) note: this test will consume a low number of packets. Since this test is for copper cable, the port with fiber cable ...

  • Page 242

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 237 dgs-3620-28sc:admin# cable_diag ports 1:1-1:10,1:21 command: cable_diag ports 1:1-1:10,1:21 perform cable diagnostics ... Port type link status test result cable length (m) ------ ---------- ------------- ------...

  • Page 245

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 240 dgs-3620-28sc:admin#create cfm md op_domain level 2 command: create cfm md op_domain level 2 success. Dgs-3620-28sc:admin# 16-2 config cfm md description this command is used to configure the parameters of a mai...

  • Page 246

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 241 dgs-3620-28sc:admin# 16-3 create cfm ma description this command is used to create a maintenance association. Different mas in a md must have different ma names. Different mas in different mds may have the same ...

  • Page 248

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 243 restrictions only administrator, operator and power-user level users can issue this command. (ei mode only command) example to configure the parameters of a maintenance association: dgs-3620-28sc:admin#config cf...

  • Page 249

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 244 restrictions only administrator, operator and power-user level users can issue this command. (ei mode only command) example to create an mep: dgs-3620-28sc:admin#create cfm mep mep1 mepid 1 md op_domain ma op1 d...

  • Page 250

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 245 characters. Ma_index - specifies the maintenance association index. - enter the maintenance association index value here. This value must be between 1 and 4294967295. State - specifies the mep administrative sta...

  • Page 252

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 247 - enter the maintenance association index value here. This value must be between 1 and 4294967295. Md - specifies the maintenance domain name. - enter the maintenance domain name. The maximum length is 22 charac...

  • Page 253

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 248 command: delete cfm md op_domain success. Dgs-3620-28sc:admin# 16-10 enable cfm description this command is used to enable the cfm globally. Format enable cfm parameters none. Restrictions only administrator, op...

  • Page 254

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 249 restrictions only administrator, operator and power-user level users can issue this command. (ei mode only command) example to disable the cfm globally: dgs-3620-28sc:admin#disable cfm command: disable cfm succe...

  • Page 255

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 250 dgs-3620-28sc:admin# 16-13 show cfm ports description this command is used to display the cfm state of specified ports. Format show cfm ports parameters - enter the logical port list. Restrictions none. (ei mode...

  • Page 256

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 251 md_index - specifies the maintenance domain index. - enter the maintenance domain index value here. This value must be between 1 and 4294967295. Ma - (optional) specify the maintenance association name. - enter ...

  • Page 257

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 252 characters. Ma_index - specifies the maintenance association index. - enter the maintenance association index value here. This value must be between 1 and 4294967295. Restrictions none. (ei mode only command) ex...

  • Page 258

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 253 mac address: 00-05-78-82-32-01 md name ma name mepid level direction vid ----------- ---------- ------- ------- --------- --- op_domain op1 1 2 inward 2 cust_domain cust1 8 4 inward 2 serv_domain serv2 mip 3 2 d...

  • Page 259

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 254 command: cfm lock md op-domain ma op-ma mepid 1 remote_mepid 2 action start success. Dgs-3620-28sc:admin# 16-18 cfm loopback description this command is used to start a cfm loopback test. Press ctrl+c to exit th...

  • Page 260

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 255 example to start a cfm loopback test: dgs-3620-28sc:admin#cfm loopback 00-01-02-03-04-05 mepname mep1 command: cfm loopback 00-01-02-03-04-05 mepname mep1 request timed out. Request timed out. Reply from mpid 52...

  • Page 261

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 256 restrictions none. (ei mode only command) example to transmit a ltm: dgs-3620-28sc:admin#cfm linktrace 00-01-02-03-04-05 mepname mep1 command: cfm linktrace 00-01-02-03-04-05 mepname mep1 transaction id: 26 succ...

  • Page 262

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 257 dgs-3620-28sc:admin#show cfm linktrace mepname mep1 command: show cfm linktrace mepname mep1 trans id source mep destination -------- ------------- ------------------ 26 mep1 xx-xx-xx-xx-xx-xx dgs-3620-28sc:admi...

  • Page 263

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 258 restrictions none. (ei mode only command) example to delete the cfm link trace reply: dgs-3620-28sc:admin#delete cfm linktrace mepname mep1 command: delete cfm linktrace mepname mep1 success. Dgs-3620-28sc:admin...

  • Page 264

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 259 16-23 show cfm mipccm description this command is used to display the mip ccm database entries. All entries in the mip ccm database will be displayed. An mip ccm entry is similar to an fdb which keeps the forwar...

  • Page 265

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 260 restrictions none. (ei mode only command) example to display the configuration of the all-mps-reply-to-ltr function: dgs-3620-28sc:admin#show cfm mp_ltr_all command: show cfm mp_ltr_all all mps reply ltrs: disab...

  • Page 266

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 261 all 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 cfm tx statistics ---------------------------------------------------------- port allpkt ccm lbr lbm ltr ltm ----- -------- -------- -------- --------- ---...

  • Page 267

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 262 to clear the cfm packet ccm counters: dgs-3620-28sc:admin#clear cfm pkt_cnt ccm command: clear cfm pkt_cnt ccm success. Dgs-3620-28sc:admin# 16-27 show cfm remote_mep description this command is used to display ...

  • Page 268

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 263 mac address : 00-11-22-33-44-02 status : ok rdi : yes port state : blocked interface name : down last ccm serial number : 1000 send chassis id : 00-11-22-33-44-00 sender management address: snmp-udp-ipv4 10.90.9...

  • Page 269

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 264 example to configure the ais function so that it is enabled and has a client level of 5: dgs-3620-28sc:admin# config cfm ais md op-domain ma op-ma mepid 1 state enable level 5 command: config cfm ais md op-domai...

  • Page 270

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 265 example to configure the lck function state as enabled and specify a client level of 5: dgs-3620-28sc:admin# config cfm lock md op-domain ma op-ma mepid 1 state enable level 5 command: config cfm lock md op-doma...

  • Page 271

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 266 messages and the percentile of the frame delay measurement test. To calculate the fdv, continuous received dmr frames are needed. Users can abort the frame delay measurement test by disable frame delay measureme...

  • Page 272

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 267 dgs-3620-28sc:admin#cfm dm 00-01-02-03-04-05 mepname mep1 period:interval 1sec:10sec percentile 75 pdu_priority 7 command: cfm dm 00-01-02-03-04-05 mepname mep1 period:interval 1sec:10sec percentile 75 pdu_prior...

  • Page 273

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 268 example to start a frame loss measurement test: dgs-3620-28sc:admin#cfm lm 00-01-02-03-04-05 mepname mep1 period 1s pdu_priority 7 command: cfm lm 00-01-02-03-04-05 mepname mep1 period 1sec pdu_priority 7 succes...

  • Page 274

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 269 dgs-3620-28sc:admin#clear cfm dm mepname mep1 command: clear cfm dm mepname mep1 success. Dgs-3620-28sc:admin# 16-34 clear cfm lm description this command is used to clear the frame loss measurement information....

  • Page 277

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 272 parameters mepname - specifies the mep name. - enter the mep name. This name can be up to 32 characters long. Mepid - specifies the mep id. - enter the mep id. This value must be between 1 and 8191. Md - specifi...

  • Page 279: Chapter 17

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 274 chapter 17 command list history commands ? {} show command_history config command_history 17-1 ? Description this command is used to display all of the commands available, on the current login account level, thr...

  • Page 280

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 275 clear counters clear dhcp binding clear dhcp conflict_ip clear ethernet_oam ports clear fdb clear historical_counters ports clear igmp_snooping data_driven_group clear igmp_snooping statistic counter clear jwac ...

  • Page 281

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 276 config traffic_segmentation 1-6 forward_list 7-8 config radius delete 1 config radius add 1 10.48.74.121 key dlink default config 802.1x reauth port_based ports all config 802.1x init port_based ports all config...

  • Page 282: Chapter 18

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 277 chapter 18 command logging command list enable command logging disable command logging show command logging 18-1 enable command logging description the enable command logging command is used to enable the comman...

  • Page 283

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 278 format disable command logging parameters none. Restrictions only administrator-level users can issue this command. Example to disable the command logging: dgs-3620-28sc:admin# disable command logging command: d...

  • Page 285

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 280 ebgp - configure the preference of bgp as-external route. (ei mode only parameter) ibgp - configure the preference of bgp as-internal route. (ei mode only parameter) - enter the route preference value here. This...

  • Page 286

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 281 dgs-3620-28sc:admin#show route preference command: show route preference route preference settings protocol preference ---------- ---------- rip 100 static 60 default 1 local 0 ospf intra 80 ospf inter 90 ospf e...

  • Page 287

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 282 restrictions only administrator, operator and power-user level users can issue this command. Example to add route redistribution to ospf: dgs-3620-28sc:admin# create route redistribute dst ospf src rip command: ...

  • Page 288

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 283 example to configure route redistributions: dgs-3620-28sc:admin# config route redistribute dst ospf src rip mettype 1 metric 2 command: config route redistribute dst ospf src rip mettype 1 metric 2 succuss. Dgs-...

  • Page 289

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 284 dgs-3620-28sc:admin# create route redistribute dst rip src ospf all metric 2 command: create route redistribute dst rip src ospf all metric 2 success. Dgs-3620-28sc:admin# 19-6 config route redistribute dst rip ...

  • Page 290

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 285 dgs-3620-28sc:admin# config route redistribute dst rip src ospf internal command: config route redistribute dst rip src ospf internal success. Dgs-3620-28sc:admin# 19-7 delete route redistribute dst rip src desc...

  • Page 291

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 286 parameters local - to redistribute local routes to bgp. Static - to redistribute static routes to bgp. Rip - to redistribute rip routes to bgp. Ospf - to redistribute ospf routes to bgp. All - to redistribute bo...

  • Page 292

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 287 rip - to redistribute rip routes to bgp. Ospf - to redistribute ospf routes to bgp. All - to redistribute both ospf as-internal and ospf as-external routes to bgp. Internal - to redistribute only the ospf as-int...

  • Page 293

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 288 example to display route redistributions: dgs-3620-28sc:admin#show route redistribute command: show route redistribute route redistribution settings source destination type metric routemapname protocol protocol ...

  • Page 294

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 289 dgs-3620-28sc:admin#show route redistribute dst rip command: show route redistribute dst rip route redistribution settings source destination type metric routemapname protocol protocol -------- ------------ ----...

  • Page 295

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 290 19-13 delete route redistribute dst ospf src description this command is used to delete the route redistribute configuration on the switch. It specifies to not redistribute other routing protocols to ospf. Forma...

  • Page 296

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 291 restrictions none. (ei mode only command) example to display route redistributions: dgs-3620-28sc:admin#show route redistribute dst bgp command: show route redistribute dst bgp route redistribution settings sour...

  • Page 297

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 292 dgs-3620-28sc:admin#show route redistribute dst ospf command: show route redistribute dst ospf route redistribution settings source destination type metric routemapname protocol protocol -------- ------------ --...

  • Page 299

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 294 example to assign a static vlan to be a guest vlan: dgs-3620-28sc:admin#create authentication guest_vlan vlan guestvlan command: create authentication guest_vlan vlan guestvlan success. Dgs-3620-28sc:admin# 20-2...

  • Page 301

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 296 hyphen - specifies using the “-“ as delimiter, the format is: aa-bb-cc-dd-ee-ff colon - specifies using the “:“ as delimiter, the format is: aa:bb:cc:dd:ee:ff dot - specifies using the “.“ as delimiter, the form...

  • Page 302

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 297 then pass. Dot1x_impb - dot1x will be verified first, and then impb will be verified. Both authentications need to be passed. Impb_jwac - jwac will be verified first, and then impb will be verified. Both authent...

  • Page 303

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 298 example to display the global authentication configuration: dgs-3620-28sc:admin#show authentication command: show authentication authentication server failover: block. Dgs-3620-28sc:admin# 20-7 show authenticati...

  • Page 304

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 299 parameters none. Restrictions none. Example to display the authentication mac format setting: dgs-3620-28sc:admin#show authentication mac_format command: show authentication mac_format case : uppercase delimiter...

  • Page 305

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 300 dgs-3620-28sc:admin#show authentication ports 1-3 command: show authentication ports 1-3 port methods auth mode authentication vlan(s) ---- -------------- ----------- ---------------------- 1 none host-based 2 n...

  • Page 306

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 301 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable the authorization global state: dgs-3620-28sc:admin#disable authorization attribut...

  • Page 307

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 302 * use the local database to authenticate the client. The switch will resort to using the local database to authenticate the client. If the client fails on local authentication, the client is regarded as un-authe...

  • Page 309

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 304 debug bgp show peer_group debug bgp show network debug bgp show aggregate debug bgp show damp debug bgp show interface_info debug bgp show as_path_access_list debug bgp show bgp_timer debug bgp show community_li...

  • Page 310

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 305 state - specifies the state of the address binding debugging option. Enable - specifies that the address binding debugging option will be enabled. Disable - specifies that the address binding debugging option wi...

  • Page 312

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 307 gp($28) : 8180ada0 sp($29) : 4cfea7a0 fp($30) : 00000001 ra($31) : 80a02938 ------------------------- task stacktrace ------------------------ ->81150a58 ->809b346c ->809e1dec ->809d7e6c ->80a038cc ->80a033b0 ->...

  • Page 313

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 308 dump - display the debug message in the debug buffer. Clear - clear the debug buffer. Upload_totftp - upload the debug buffer to a tftp server specified by ip address. - specifies the ipv4 address of the tftp se...

  • Page 314

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 309 the system memory pool resource may fail to execute command such as download and upload firmware, or save configuration. If you want to execute these commands successfully, please use the command “debug buffer c...

  • Page 315

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 310 restrictions only administrator level users can issue this command. Example to set the switch to not need a reboot when a fatal error occurs: dgs-3620-28sc:admin# debug config error_reboot disable command: debug...

  • Page 316

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 311 format debug show error_reboot state parameters none. Restrictions only administrator level users can issue this command. Example to show the error reboot status: dgs-3620-28sc:admin#debug show error_reboot stat...

  • Page 317

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 312 dgs-3620-28sc:admin# debug stp clear counter ports all command : debug stp clear counter ports all success. Dgs-3620-28sc:admin# 21-10 debug stp config ports description this command used to configure per-port s...

  • Page 319

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 314 format debug stp show flag {ports } parameters ports - (optional) specifies the stp ports to display. - (optional) enter the list of port used for this configuration here. If no parameter is specified, all ports...

  • Page 320

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 315 parameters none. Restrictions only administrator level users can issue this command. Example to show stp debug information: dgs-3620-28sc:admin# debug stp show information command: debug stp show information spa...

  • Page 321

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 316 message age : 0 max age : 20 forward delay : 15 hello time : 2 instance 1: port 1 : regional root bridge : 0 /00-00-00-00-00-00 internal root cost : 0 designated bridge : 0 /00-00-00-00-00-00 designated port : 0...

  • Page 323

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 318 dgs-3620-28sc:admin# debug ospf neighbor_state_change state enable command: debug ospf neighbor_state_change state enable success. Dgs-3620-28sc:admin# to enable ospf interface state change debug: dgs-3620-28sc:...

  • Page 325

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 320 example to enable the ospf debug log: dgs-3620-28sc:admin# debug ospf log state enable command: debug ospf log state enable success. Dgs-3620-28sc:admin# 21-18 debug ospf show counter description this command is...

  • Page 326

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 321 lsr : 0 lsu : 0 lsack : 0 neighbor state: change : 0 seqmismatch : 0 spf calculation: intra : 0 inter : 0 extern : 0 dgs-3620-28sc:admin# 21-19 debug ospf show detail external_link description this command is us...

  • Page 327

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 322 .... .0.. = mc: not multicast capable .... 0... = n/p: nssa bit ...0 .... = ea: not support rcv and fwd ea_lsa ..0. .... = dc: not support handling of demand circuits .0.. .... = o: o bit isn't set 0... .... = 7...

  • Page 328

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 323 ls age: 109 seconds options: 0x2 .... ...0 = 0 bit isn't set .... ..1. = e: externalroutingcapability .... .0.. = mc: not multicast capable .... 0... = n/p: nssa bit ...0 .... = ea: not support rcv and fwd ea_ls...

  • Page 329

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 324 advertising router: 1.1.1.1 ls age: 10 seconds options: 0x2 .... ...0 = 0 bit isn't set .... ..1. = e: externalroutingcapability .... .0.. = mc: not multicast capable .... 0... = n/p: nssa bit ...0 .... = ea: no...

  • Page 330

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 325 =========== area 0.0.0.0: summary lsa: link-state id: 20.1.1.0 advertising router: 10.90.90.91 ls age: 10 seconds options: 0x2 .... ...0 = 0 bit isn't set .... ..1. = e: externalroutingcapability .... .0.. = mc:...

  • Page 331

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 326 ospf phase2 nssa-external link: =========== area 0.0.0.1: nssa-external lsa: link-state id: 0.0.0.0 advertising router: 10.90.90.91 ls age: 855 seconds options: 0x2 .... ...0 = 0 bit isn't set .... ..1. = e: ext...

  • Page 332

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 327 example to show the current ospf debug flag setting: dgs-3620-28sc:admin# debug ospf show flag command: debug ospf show flag global state: enabled current ospf flags setting: neighbor state change interface stat...

  • Page 333

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 328 dgs-3620-28sc:admin# debug ospf show log state command: debug ospf show log state ospf log state : enabled dgs-3620-28sc:admin# 21-26 debug ospf show redistribution description this command is used to display th...

  • Page 334

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 329 format debug ospf show request_list parameters none. Restrictions only administrator level users can issue this command. Example to display the current ospf request list: dgs-3620-28sc:admin# debug ospf show req...

  • Page 335

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 330 example to display the current ospf summary list: dgs-3620-28sc:admin# debug ospf show summary_list command: debug ospf show summary_list ospf summary list: area 0.0.0.0: circuit: 1.1.1.1 neighbor: 90.2.0.1 ip: ...

  • Page 336

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 331 dgs-3620-28sc:admin# debug ospf state enable command: debug ospf state enable success. Dgs-3620-28sc:admin# debug ospf show flag command: debug ospf show flag global state: enabled current ospf flags setting: ne...

  • Page 337

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 332 dgs-3620-28sc:admin# debug vrrp vr_state_change state enable command: debug vrrp vr_state_change state enable success. Dgs-3620-28sc:admin# to enable all vrrp packet debug flags: dgs-3620-28sc:admin# debug vrrp ...

  • Page 338

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 333 format debug vrrp clear counter parameters none. Restrictions only administrator level users can issue this command. Example to clear vrrp statistic counters: dgs-3620-28sc:admin# debug vrrp clear counter comman...

  • Page 339

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 334 dgs-3620-28sc:admin# debug vrrp log state enable command: debug vrrp log state enable success. Dgs-3620-28sc:admin# 21-33 debug vrrp show counter description this command is used to display the vrrp debug statis...

  • Page 340

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 335 parameters none. Restrictions only administrator level users can issue this command. Example to display vrrp debug flag settings: dgs-3620-28sc:admin#debug vrrp show flag command: debug vrrp show flag global sta...

  • Page 341

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 336 dgs-3620-28sc:admin# debug vrrp show log state command: debug vrrp show log state vrrp debug log state: disabled dgs-3620-28sc:admin# 21-36 debug vrrp state description the command is used to enable or disable t...

  • Page 342

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 337 restrictions only administrator-level users can issue this command. (ei mode only command) example show bgp debug flag: dgs-3620-28sc:admin# debug bgp show flag command: debug bgp show flag current bgp flags set...

  • Page 343

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 338 restrictions only administrator-level users can issue this command. (ei mode only command) example configure all bgp debug flags’ state to enable: dgs-3620-28sc:admin# debug bgp all flag enable command: debug bg...

  • Page 345

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 340 bgp:peer: rcv open, version:,remote-as:, holdtime:,rid: bgp:peer: rcv keepalive. Bgp:peer: rcv update, withdraw: ,,, ,... Bgp:peer: rcv update,attr: hop:10.1.1.10,med:5>, nlri: , bgp:peer: rcv notifycation,code:...

  • Page 346

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 341 21-42 debug bgp show global_info description this command is used for displaying global information of current bgp instance. Format debug bgp show global_info parameters none. Restrictions only administrator-lev...

  • Page 347

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 342 bgp trap : none dgs-3620-28sc:admin# 21-43 debug bgp show peer description this command is used for displaying information of all peers in bgp protocol db. Format debug bgp show peer parameters none. Restriction...

  • Page 348

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 343 remove private as: disabled allowas in: disabled graceful restart : disabled address family ipv4 unicast ipv4 unicast: none soft reconfiguration inbound: enabled community sent to this neighbor: none default ori...

  • Page 349

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 344 dgs-3620-28sc:admin# :5#debug bgp show peer_group command: debug bgp show peer_group bgp peer group :tt ------------------------------------------------------- session state : enabled session activity : enabled ...

  • Page 350

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 345 example configure bgp to show network information: dgs-3620-28sc:admin# debug bgp show network command: debug bgp show network network route map ------------- ----------- 192.168.0.0/8 null 172.16.0.0/16 map1 to...

  • Page 351

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 346 21-47 debug bgp show damp description this command is used for displaying current dampening configuration and corresponding dynamic information in bgp protocol stack. Format debug bgp show damp parameters none. ...

  • Page 352

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 347 3 0.940247 4 0.911722 5 0.884064 6 0.857244 7 0.831238 8 0.806021 9 0.781569 10 0.757858 output truncated... Dgs-3620-28sc:admin# 21-48 debug bgp show interface_info description this command is used for displayi...

  • Page 353

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 348 format debug bgp show as_path_access_list parameters none. Restrictions only administrator-level users can issue this command. (ei mode only command) example configure bgp to show current bgp as_path access_list...

  • Page 354

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 349 dgs-3620-28sc:admin# debug bgp show bgp_timer command: debug bgp show bgp_timer bgp timer link: node time func ---- ---- ------ 08b108d0 0001 00675af4 08b1ac70 0016 0065f4f4 08b1aca8 0017 0065f5cc 08b37dcc 0029 ...

  • Page 355

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 350 21-52 debug bgp show redist_info description this command is used for displaying current bgp redistribution information. Format debug bgp show redist_info parameters none. Restrictions only administrator-level u...

  • Page 356

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 351 parameters enable - enable the route_map debug function. Disable - disable the route_map debug function. Restrictions only administrator-level users can issue this command. (ei mode only command) example configu...

  • Page 357

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 352 example configure access list debug flags’ state to enable: dgs-3620-28sc:admin# debug bgp access_list enable command: debug bgp access_list enable success. Dgs-3620-28sc:admin# output examples: after configure ...

  • Page 359

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 354 example to enabled dhcpv6 client debug function: dgs-3620-28sc:admin# debug dhcpv6_client state enable command: debug dhcpv6_client state enable success. Dgs-3620-28sc:admin# 21-58 debug dhcpv6_client state disa...

  • Page 360

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 355 parameters buffer - let the debug message output to buffer. Console - let the debug message output to console. Restrictions only administrator-level users can issue this command. Example to set debug information...

  • Page 361

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 356 21-61 debug dhcpv6_relay state enable description this command is used to enable the dhcpv6 relay debug function. Format debug dhcpv6_relay state enable parameters none. Restrictions only administrator-level use...

  • Page 362

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 357 dgs-3620-28sc:admin# debug dhcpv6_relay state disable command: debug dhcpv6_relay state disable success. Dgs-3620-28sc:admin# 21-63 debug dhcpv6_relay hop_count state description this command is used to enable o...

  • Page 363

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 358 console - let the debug message output to console. Restrictions only administrator-level users can issue this command. Example to set debug information to output to console: dgs-3620-28sc:admin# debug dhcpv6_rel...

  • Page 364

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 359 21-66 debug dhcpv6_server packet description this command is used to enable or disable the debug information flag of the dhcpv6 server packet, including packets receiving and sending. Format debug dhcpv6_server ...

  • Page 365

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 360 example to disabled the dhcpv6 server debug function: dgs-3620-28sc:admin# debug dhcpv6_server state disable command: debug dhcpv6_server state disable success. Dgs-3620-28sc:admin# 21-68 debug dhcpv6_server sta...

  • Page 366

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 361 parameters none. Restrictions only administrator-level users can issue this command. Example to enable the pim-ssm debug function: dgs-3620-28sc:admin# debug pim ssm command: debug pim ssm success. Dgs-3620-28sc...

  • Page 367

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 362 dgs-3620-28sc:admin# no debug pim ssm command: no debug pim ssm success. Dgs-3620-28sc:admin# 21-71 debug ripng flag description this command is used to enable or disable the ripng debug flag. Format debug ripng...

  • Page 368

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 363 21-72 debug ripng show flag description this command is used to display the ripng debug flag setting. Format debug ripng show flag parameters none. Restrictions only administrator-level users can issue this comm...

  • Page 369

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 364 example to disable ripng debug globally: dgs-3620-28sc:admin# debug ripng state disable command: debug ripng state disable success. Dgs-3620-28sc:admin# 21-74 debug ripng state enable description this command is...

  • Page 370

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 365 parameters prefix_list - specifies to display prefix list debug information. Access_list - specifies to display access list debug information. Route_map - specifies to display route map debug information. Restri...

  • Page 371

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 366 prompt# debug show status module mstp command: debug show status module mstp debug global state : enable mstp : enable prompt# to show the debug state: prompt# debug show status command: debug show status debug ...

  • Page 372

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 367 dgs-3620-28sc:admin# debug super_vlan state disable command: debug super_vlan state disable success. Dgs-3620-28sc:admin# after enabling super vlan debug, the following information may appear when receive an arp...

  • Page 373

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 368 to display the nd snooping binding state of entries: dgs-3620-28sc:admin# debug show address_binding binding_state_table nd_snooping command: debug show address_binding binding_state_table nd_snooping s (state) ...

  • Page 374

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 369 dgs-3620-28sc:admin#debug show error ports box_id all sio1 command: debug show error ports box_id all sio1 box id 1 sio 1: rx frames tx frames --------- --------- crc error 0 excessive deferral 0 undersize 0 crc...

  • Page 375

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 370 dgs-3620-28sc:admin#debug show jwac auth_info command: debug show jwac auth_info acl index bitmap db (jwac_db_acl_bmp): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0...

  • Page 376

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 371 page 1: dgs-3620-28sc:admin#debug show packet ports box_id all sio1 command: debug show packet ports box_id all sio1 box id 1 sio 1: frame size/type frame counts frames/sec --------------- ----------------------...

  • Page 379

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 374 dgs-3620-28sc:admin#enable dhcp_local_relay command: enable dhcp_local_relay success. Dgs-3620-28sc:admin# 22-4 disable dhcp_local_relay description this command is used to globally disable the dhcp local relay ...

  • Page 380

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 375 restrictions none. Example to display the local dhcp relay status: dgs-3620-28sc:admin#show dhcp_local_relay command: show dhcp_local_relay dhcp/bootp local relay status : disabled dhcp/bootp local relay vid lis...

  • Page 382

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 377 parameters hops - specifies the maximum number of router hops that the dhcp/bootp packets can cross. The range is 1 to 16. The default value is 4. - enter the maximum number of router hops that the dhcp/bootp pa...

  • Page 383

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 378 dgs-3620-28sc:admin#config dhcp_relay add ipif system 10.43.21.12 command: config dhcp_relay add ipif system 10.43.21.12 success. Dgs-3620-28sc:admin# 23-3 config dhcp_relay delete ipif description this command ...

  • Page 384

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 379 parameters - enter a string. Relay - specifies a relay server ip address. - enter the ip address here. Exact-match - the option 60 string in the packet must fully match the specified string. Partial-match - the ...

  • Page 385

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 380 example to configure a dhcp option 60 default drop action: dgs-3620-28sc:admin#config dhcp_relay option_60 default mode drop command: config dhcp_relay option_60 default mode drop success. Dgs-3620-28sc:admin# 2...

  • Page 386

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 381 23-7 config dhcp_relay option_60 state description this command is used to decide whether dhcp relay will process the dhcp option 60 or not. When option 60 is enabled, if the packet does not have option 60, then...

  • Page 387

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 382 - enter the client’s client-id, which is the mac address of the client. String - specifies the client’s client-id, which is specified by administrator. - enter the client’s client-id, which is specified by admin...

  • Page 388

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 383 dgs-3620-28sc:admin#config dhcp_relay option_61 default drop command: config dhcp_relay option_61 default drop success. Dgs-3620-28sc:admin# 23-10 config dhcp_relay option_61 delete description this command is u...

  • Page 390

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 385 success. Dgs-3620-28sc:admin# 23-13 config dhcp_relay option_82 policy description this option takes effect only when the check status is disabled. The relay agent does this operation because the packet cannot c...

  • Page 391

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 386 parameters default - use the switch’s system mac address as remote id. User_define - use the user-defined string as remote id. Space characters are allowed in the string. - the user-defined string can be up to 3...

  • Page 392

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 387 success. Dgs-3620-28sc:admin# 23-16 enable dhcp_relay description this command is used to enable the dhcp relay function on the switch. Format enable dhcp _relay parameters none. Restrictions only administrator,...

  • Page 393

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 388 example to disable the dhcp relay function: dgs-3620-28sc:admin#disable dhcp_relay command: disable dhcp_relay success. Dgs-3620-28sc:admin# 23-18 show dhcp_relay description this command is used to display the ...

  • Page 395

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 390 dgs-3620-28sc:admin# 23-20 show dhcp_relay option_61 description this command is used to display all the dhcp relay option 61 rules. Format show dhcp_relay option_61 parameters none. Restrictions none. Example t...

  • Page 396

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 391 parameters - enter the list of ports, used for this configuration, here. All - specifies that all the ports will be used for this configuration. State - specifies the state of the dhcp relay function for each po...

  • Page 397

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 392 1:2 enabled 1:3 enabled 1:4 enabled 1:5 enabled 1:6 enabled 1:7 enabled 1:8 enabled 1:9 enabled 1:10 enabled total entries : 10 dgs-3620-28sc:admin#.

  • Page 399

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 394 parameters begin_address - specifies the starting address of the ip address range. - enter the starting address of the ip address range. End_address - specifies the ending address of the ip address range. - ente...

  • Page 400

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 395 command: delete dhcp excluded_address begin_address 10.10.10.1 end_address 10.10.10.10 success. Dgs-3620-28sc:admin# 24-3 show dhcp excluded_address description this command is used to display the groups of ip a...

  • Page 401

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 396 parameters - enter the name of the dhcp pool. Restrictions only administrator, operator and power-user level users can issue this command. Example to create a dhcp pool: dgs-3620-28sc:admin#create dhcp pool nykn...

  • Page 402

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 397 24-6 config dhcp pool network_addr description this command is used to specify the network for the dhcp pool. The addresses in the network are free to be assigned to the dhcp client. The prefix length specifies ...

  • Page 403

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 398 parameters - enter the dhcp pool name. - (optional) specify the domain name of the client. Restrictions only administrator, operator and power-user level users can issue this command. Example to configure the do...

  • Page 404

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 399 24-9 config dhcp pool netbios_name_server description this command is used to specify the netbios wins server that is available to a microsoft dhcp client. Up to three ip addresses can be specified on one comman...

  • Page 405

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 400 parameters - enter the dhcp pool name. Broadcast - specifies the netbios node type for microsoft dhcp clients as broadcast. Peer_to_peer - specifies the netbios node type for microsoft dhcp clients as peer_to_pe...

  • Page 406

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 401 example to configure the default router: dgs-3620-28sc:admin#config dhcp pool default_router nyknicks 10.10.10.1 command: config dhcp pool default_router nyknicks 10.10.10.1 success. Dgs-3620-28sc:admin# 24-12 c...

  • Page 407

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 402 second command will overwrite the first command. If the bootfile is not specified, the boot file information will not be provided to the client. Format config dhcp pool boot_file {} parameters - enter the dhcp p...

  • Page 408

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 403 dgs-3620-28sc:admin#config dhcp pool next_server engineering 192.168.0.1 command: config dhcp pool next_server engineering 192.168.0.1 success. Dgs-3620-28sc:admin# 24-15 config dhcp ping_packets description thi...

  • Page 409

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 404 format config dhcp ping_timeout parameters - enter the amount of time the dhcp server must wait before timing out a ping packet. The default value is 100. Restrictions only administrator, operator and power-user...

  • Page 410

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 405 ieee802 -specify ieee802 type. Restrictions only administrator, operator and power-user level users can issue this command. Example to configure manual bindings: dgs-3620-28sc:admin#create dhcp pool manual_bindi...

  • Page 411

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 406 24-19 clear dhcp binding description this command is used to clear a binding entry or all binding entries in a pool or clears all binding entries in all pools. Note that this command will not clear the dynamic b...

  • Page 412

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 407 example to display dynamic binding entries for “engineering”: dgs-3620-28sc:admin#show dhcp binding engineering command: show dhcp binding engineering pool name ip addresss hardware address type status lifetime ...

  • Page 413

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 408 next server : 10.10.10.2 dgs-3620-28sc:admin# 24-22 show dhcp pool manual_binding description this command is used to display the configured manual binding entries. Format show dhcp pool manual_binding {} parame...

  • Page 414

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 409 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to enable dhcp server: dgs-3620-28sc:admin#enable dhcp_server command: enable dhcp_server suc...

  • Page 415

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 410 24-25 show dhcp_server description this command is used to display the current dhcp server configuration. Format show dhcp_server parameters none. Restrictions none. Example to display the dhcp server status: dg...

  • Page 416

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 411 example to clear an ip address 10.20.3.4 from the conflict database: dgs-3620-28sc:admin#clear dhcp conflict_ip 10.20.3.4 command: clear dhcp conflict_ip 10.20.3.4 success. Dgs-3620-28sc:admin# 24-27 show dhcp c...

  • Page 417

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 412 format create dhcp option_profile parameters - enter the dhcp option profile name here. This name can be up to 12 characters long. Restrictions only administrator, operator and power-user level users can issue t...

  • Page 418

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 413 restrictions only administrator, operator and power-user level users can issue this command. Example to add option 69 using hex format: dgs-3620-28sc:admin#config dhcp option_profile profile1 add option 69 hex c...

  • Page 419

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 414 example to delete a dhcp option profile. Dgs-3620-28sc:admin#delete dhcp option_profile profile1 command: delete dhcp option_profile profile1 success. Dgs-3620-28sc:admin# 24-31 show dhcp option_profile descript...

  • Page 422

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 417 client_mac - (optional) specify the mac address of the dhcp client. - enter the mac address. Ports - specifies the ports. - enter the range of ports to be configured. All - specifies to configure all ports. Dele...

  • Page 424

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 419 25-4 show filter dhcp_server description this command is used to display the dhcp server/client filter list created on the switch. Format show filter dhcp_server parameters none. Restrictions none. Example to di...

  • Page 425

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 420 parameters - specifies the source address of the entry which will be created into the filter dhcpv6 server forward list. Ports - specifies the list of ports used for this configuration. - enter the list of ports...

  • Page 426

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 421 25-7 config filter dhcpv6_server ports description this command is used to configure the state of filter dhcpv6 server packets on the switch. The filter dhcpv6 server function is used to filter the dhcpv6 server...

  • Page 427

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 422 restrictions only administrator, operator and power-user level users can issue this command. Example to enable the filter dhcpv6 server trap state: dgs-3620-28sc:admin#config filter dhcpv6_server trap enable com...

  • Page 428

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 423 25-10 delete filter dhcpv6_server permit sip description this command is used to delete a filter dhcpv6 server permit entry. Format delete filter dhcpv6_server permit sip parameters - enter the source ipv6 addre...

  • Page 429

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 424 example to create a filter icmpv6 ra all-nodes permit entry on port 5: dgs-3620-28sc:admin#create filter icmpv6_ra_all_node permit sip 2200::5 ports 1:5 command: create filter icmpv6_ra_all_node permit sip 2200:...

  • Page 431

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 426 dgs-3620-28sc:admin#config filter icmpv6_ra_all_node trap enable command: config filter icmpv6_ra_all_node trap enable success. Dgs-3620-28sc:admin# 25-15 show filter icmpv6_ra_all_node description this command ...

  • Page 432

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 427 format delete filter icmpv6_ra_all_node permit sip parameters - enter the source ipv6 address of the entry which will be deleted in the filter icmpv6 ra all-nodes forward list. Restrictions only administrator, o...

  • Page 434

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 429 format disable dhcpv6_relay parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to configure the dhcpv6 relay global state to disable: dgs-3620-2...

  • Page 435

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 430 dgs-3620-28sc:admin# config dhcpv6_relay hop_count 4 command: config dhcpv6_relay hop_count 4 success. Dgs-3620-28sc:admin# 26-4 config dhcpv6_relay description the command could add/delete an ipv6 address which...

  • Page 436

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 431 parameters ipif - specifies the name of the ip interface. - enter the ip interface name used here. This name can be up to 12 characters long. All - specifies that all the configured ip interfaces wil be used.. S...

  • Page 437

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 432 dgs-3620-28sc:admin#show dhcpv6_relay command: show dhcpv6_relay dhcpv6 relay global state : disabled dhcpv6 hops count limit : 4 dhcpv6 relay information option 37 state : disabled dhcpv6 relay information opti...

  • Page 439

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 434 dgs-3620-28sc:admin#config dhcpv6_relay option_37 remote_id default command: config dhcpv6_relay option_37 remote_id default success. Dgs-3620-28sc:admin#.

  • Page 441

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 436 dgs-3620-28sc:admin# create dhcpv6 pool pool1 command : create dhcpv6 pool pool1 success dgs-3620-28sc:admin# 27-2 delete dhcpv6 pool description this command is used to delete one or all dhcpv6 pools. Format de...

  • Page 442

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 437 - (optional) enter the dhcpv6 pool name to be displayed here. This name can be up to 12 characters long. If no parameters are specified, all the dhcpv6 pools will be displayed. Restrictions none. Example to show...

  • Page 443

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 438 format config dhcpv6 pool ipv6network_addr begin end parameters - enter the dhcpv6 pool name used here. This name can be up to 12 characters long. Begin - specifies the beginning ipv6 network address of the dhcp...

  • Page 444

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 439 restrictions only administrator, operator and power-user level users can issue this command. Example to configure the domain name for the dhcpv6 pool pool1: dgs-3620-28sc:admin# config dhcpv6 pool domain_name po...

  • Page 445

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 440 27-7 config dhcpv6 pool lifetime description this command is used to configure the preferred-lifetime and valid-lifetime of ipv6 address within a dhcpv6 pool. Preferred lifetime - the length of time that a valid...

  • Page 447

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 442 - enter the ipv6 prefix assigned to the pool here. - enter the length of the prefix, in bits, assigned to the user from the pool here. The value of the assigned-length argument cannot be less than the value of t...

  • Page 448

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 443 dgs-3620-28sc:admin# show dhcpv6 manual_binding command: show dhcpv6 manual_binding pool name :net100 entry 1 ipv6 address: 3000:100:1::abcd duid : 00030006001572200700 pool name :net91 entry 1 ipv6 address: 300...

  • Page 449

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 444 dgs-3620-28sc:admin# show dhcpv6 binding command: show dhcpv6 binding pool name: net90 ipv6 address: 3000:90:1::7 duid : 0003000600cd14517000 preferred(s): 120 valid(s): 240 pool name: net100-2 ipv6 address: 300...

  • Page 450

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 445 format enable dhcpv6_server parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to configure the dhcpv6 server global state to enable: dgs-3620-2...

  • Page 451

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 446 27-15 show dhcpv6_server description this command is used to display the dhcpv6 server setting. Format show dhcpv6_server {ipif } parameters ipif - (optional) specifies the ip interface name to be displayed. - e...

  • Page 452

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 447 characters long. Add - specifies to add an excluded address range for a specified pool. Begin - specifies the beginning ipv6 address of the range of ipv6 addresses to be excluded from the dhcpv6 pool. - enter th...

  • Page 453

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 448 example to display the excluded address information: dgs-3620-28sc:admin# show dhcpv6 excluded_address command: show dhcpv6 excluded_address pool name: net100 range 1 begin address: 3000:110:1::1 end address : 3...

  • Page 454

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 449 dgs-3620-28sc:admin# config dhcpv6_server ipif system state enable command: config dhcpv6_server ipif system state enable success. Dgs-3620-28sc:admin#.

  • Page 456

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 451 disable - specifies that dvmrp of the specified ip interface will be disabled. Restrictions only administrator, operator and power-user level users can issue this command. (ei mode only command) example to confi...

  • Page 457

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 452 28-3 disable dvmrp description this command is used to disable the dvmrp global state on the switch. Format disable dvmrp parameters none. Restrictions only administrator, operator and power-user level users can...

  • Page 458

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 453 example to display dvmrp configurations: dgs-3620-28sc:admin#show dvmrp command: show dvmrp dvmrp global state : disabled interface ip address neighbor timeout probe metric state ------------ ----------------- -...

  • Page 459

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 454 dgs-3620-28sc:admin# show dvmrp neighbor command: show dvmrp neighbor dvmrp neighbor address table interface neighbor address generation id expire time --------------- ---------------- ------------- ----------- ...

  • Page 460

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 455 dgs-3620-28sc:admin# show dvmrp nexthop command: show dvmrp nexthop dvmrp routing next hop table source address/netmask interface name type ---------------------- --------------- ------ 10.0.0.0/8 ip2 leaf 10.0....

  • Page 461

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 456 dgs-3620-28sc:admin# show dvmrp routing_table command: show dvmrp routing_table dvmrp routing table source address/netmask upstream neighbor metric learned interface expire ---------------------- ---------------...

  • Page 462: Chapter 29

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 457 chapter 29 d-link license management system (dlms) install dlms activation_code {unit } show dlms license 29-1 install dlms activation_code description this command is used to install an activation code. The act...

  • Page 463

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 458 29-2 show dlms license description this command will display the license information. Format show dlms license {unit } parameters unit - specifies the unit to display. Specifies the switch in the switch stack. R...

  • Page 465

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 460 success. Dgs-3620-28sc:admin# to add the entry “dns1” with ip address 10.24.22.5 to the dns static table: dgs-3620-28sc:admin#config dnsr add static dns1 10.24.22.5 command: config dnsr add static dns1 10.24.22....

  • Page 466

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 461 to enable cache lookup for dns relay: dgs-3620-28sc:admin#enable dnsr cache command: enable dnsr cache success. Dgs-3620-28sc:admin# to enable static table lookup for dns relay: dgs-3620-28sc:admin#enable dnsr s...

  • Page 467

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 462 success. Dgs-3620-28sc:admin# to disable static table lookup for dns relay: dgs-3620-28sc:admin#disable dnsr static command: disable dnsr static success. Dgs-3620-28sc:admin# 30-4 show dnsr description this comm...

  • Page 468

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 463 dgs-3620-28sc:admin#show dnsr command: show dnsr dnsr status : disabled primary name server : 0.0.0.0 secondary name server : 0.0.0.0 dnsr cache status : disabled dnsr static table status : disabled dns relay st...

  • Page 471

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 466 example to configure dns resolver name server time out to 10 seconds: dgs-3620-28sc:admin# config name_server timeout 10 command: config name_server timeout 10 success. Dgs-3620-28sc:admin# 31-4 show name_server...

  • Page 473

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 468 dgs-3620-28sc:admin# delete host_name www.Example.Com command: delete host_name www.Example.Com success. Dgs-3620-28sc:admin# 31-7 show host_name description this command is used to display the current host name...

  • Page 474

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 469 total dynamic entries: 0 dgs-3620-28sc:admin# 31-8 enable dns_resolver description this command is used to enable the dns resolver state of the switch. Format enable dns_resolver parameters none. Restrictions on...

  • Page 475

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 470 example to configure the dns resolver state to disabled: dgs-3620-28sc:admin# disable dns_resolver command: disable dns_resolver success. Dgs-3620-28sc:admin#.

  • Page 477

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 472 restrictions only administrator, operator and power-user level users can issue this command. Example to configure land attack and blat attack prevention, the action is drop: dgs-3620-28sc:admin#config dos_preven...

  • Page 479

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 474 restrictions none. Example to display dos prevention information: dgs-3620-28sc:admin#show dos_prevention command: show dos_prevention trap:disabled log:enabled function version : 1.01 dos type state action fram...

  • Page 481

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 476 example to enable unidirectional link detection on port 1: dgs-3620-28sc:admin# config duld ports 1 state enable commands: config duld ports 1 state enable success dgs-3620-28sc:admin# 33-2 show duld ports descr...

  • Page 483

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 478 restrictions only administrator, operator and power-user level users can issue this command. Example to enable erps: dgs-3620-28sc:admin#enable erps command: enable erps success. Dgs-3620-28sc:admin# 34-2 disabl...

  • Page 484

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 479 format create erps raps_vlan parameters - enter the vlan which will be the r-aps vlan. Restrictions only administrator, operator and power-user level users can issue this command. Example to create an erps raps ...

  • Page 485

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 480 34-5 config erps raps_vlan description this command is used to set the r-aps vlan parameters. The ring_mel command is used to configure the ring mel for an r-aps vlan. The ring mel is one field in the r-aps pdu....

  • Page 486

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 481 holdoff timer - hold-off timer is used to filter out intermittent link faults when link failure occurs. This timer is used during the protection switching process when link failure occurs. When a ring node detec...

  • Page 487

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 482 vlanid - specifies a vlan id list. - enter a range of vlan ids. Sub_ring - specifies the sub-ring configuration. Raps_vlan - specifies the r-aps vlan. - enter the r-aps vlan id used here. Tc_propagation - specif...

  • Page 488

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 483 dgs-3620-28sc:admin#config erps raps_vlan 4094 rpl_port west command: config erps raps_vlan 4094 rpl_port west success. Dgs-3620-28sc:admin#config erps raps_vlan 4094 rpl_owner enable command: config erps raps_v...

  • Page 489

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 484 example to set the log state: dgs-3620-28sc:admin#config erps log enable command: config erps log enable success. Dgs-3620-28sc:admin# 34-7 config erps trap description this command is used to configure trap sta...

  • Page 490

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 485 format show erps {raps_vlan {sub_ring}} parameters raps_vlan - (optional) specifies the r-aps vlan. - enter the r-aps vlan id used here. Sub_ring - (optional) display the sub-ring configuration information. Rest...

  • Page 492

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 487 format show eee ports {} parameters - (optional) specify a list of ports to be displayed. Restrictions none. Example to display the eee state: dgs-3620-28sc:admin#show eee ports 1:1-1:6,1:9 command: show eee por...

  • Page 493: Chapter 36

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 488 chapter 36 external alarm commands config external_alarm {unit } channel message show external_alarm {unit } 36-1 config external_alarm description this command is used to configure external alarm message for a ...

  • Page 494

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 489 36-2 show external_alarm description this command is used to display the real-time status of external alarm. Format show external_alarm {unit } parameters unit - specifies the unit(s) to display. - enter the num...

  • Page 497

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 492 restrictions only administrator, operator and power-user level users can issue this command. Example to create multicast mac forwarding: dgs-3620-28sc:admin# create multicast_fdb default 01-00-00-00-01-01 comman...

  • Page 498

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 493 37-5 config fdb aging_time description this command is used to set the age-out timer for the switch’s dynamic unicast mac address forwarding tables. Format config fdb aging_time parameters - enter the time in se...

  • Page 499

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 494 filter_unregistered_groups - specifies the filtering mode as filter_unregistered_groups. Restrictions only administrator, operator and power-user level users can issue this command. Example to configure the the ...

  • Page 501

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 496 note: if no parameter is specified, all multicast fdb entries will be displayed. Restrictions none. Example to display multicast mac address table: dgs-3620-28sc:admin#show multicast_fdb command: show multicast_...

  • Page 502

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 497 restrictions none. Example to display unicast mac address table: dgs-3620-28sc:admin#show fdb command: show fdb unicast mac address aging time = 300 vid vlan name mac address port type status ---- --------------...

  • Page 503

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 498 dgs-3620-28sc:admin#.

  • Page 505

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 500 dgs-3620-28sc:admin#show storage_media_info command: show storage_media_info unit drive media type size label fs type version ---- ----- ---------- -------- ----------- ------- ------- 1 c: flash 123 mb ffs dgs-...

  • Page 506

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 501 parameters unit - specifies the unit id in the stacking system. If not specified, it refers to the master unit. - enter the unit id value here. - specifies the drive id. If not specified, it refers to the curren...

  • Page 507

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 502 current work directory: “c:/d1” dgs-3620-28sc:admin# 38-5 dir description this command is used to list all of the files located in a directory of a drive. If a path name is not specified, then all of the files i...

  • Page 508

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 503 dgs-3620-28sc:admin#dir c:/system command: dir c:/system system reserved directory. Used space 89kb. Dgs-3620-28sc:admin# 38-6 rename description this command is used to rename a file in the file system. The pat...

  • Page 509

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 504 parameters unit - specifies the unit id in the stacking system. If not specified, it refers to the master unit. - enter the unit id value here. - specifies the drive id. If not specified, it refers to the curren...

  • Page 510

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 505 dgs-3620-28sc:admin#format d: fat32 command: format d: fat32 formatting........................... Done! Dgs-3620-28sc:admin# 38-9 del description this command is used to delete a file. It is also used to delete...

  • Page 511

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 506 38-10 move description this command is used to move a file around the file system. Note that when a file is moved, it can be specified whether to be renamed at the same time. Format move {{unit } } {{unit } } pa...

  • Page 512

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 507 parameters unit - specifies the unit id in the stacking system. If not specified, it refers to the master unit. - enter the unit id value here. - specifies the drive id. If not specified, it refers to the curren...

  • Page 513

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 508 dgs-3620-28sc:admin# change drive unit 3 c: command: change drive unit 3 c: current work directory: "/unit3:/c:". Dgs-3620-28sc:admin#.

  • Page 515

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 510 format show filter extensive_netbios parameters none. Restrictions none. Example to display the extensive netbios filter state on the switch: dgs-3620-28sc:admin#show filter extensive_netbios command: show filte...

  • Page 516

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 511 command: config filter netbios 1-10 state enable success. Dgs-3620-28sc:admin# 39-4 show filter netbios description this command is used to display the netbios filter state on the switch. Format show filter netb...

  • Page 519

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 514 command: config gratuitous_arp learning enable success. Dgs-3620-28sc:admin# 40-4 config gratuitous_arp send dup_ip_detected description this command is used to enable or disable the sending of gratuitous arp re...

  • Page 521

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 516 command: config gratuitous_arp send periodically ipif system interval 5 success. Dgs-3620-28sc:admin# 40-7 show gratuitous_arp description this command is used to display gratuitous arp configuration. Format sho...

  • Page 523

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 518 - enter the last member query interval value here. This value must be between 1 and 25. The default value is 1. State - (optional) specifies the igmp state on a router interface. Enable - specifies that the igmp...

  • Page 524

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 519 example to display the igmp configuration for all interfaces: dgs-3620-28sc:admin#show igmp command: show igmp igmp interface configurations interface ip address/netmask ver- query maximum robust- last state sio...

  • Page 525

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 520 system 224.0.1.41 10.1.43.252 10.48.74.122 259 system 224.0.1.149 10.20.63.11 10.48.74.122 259 total entries : 3 dgs-3620-28sc:admin# 41-4 config igmp check_subscriber_source_network description this command is ...

  • Page 526

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 521 41-5 show igmp check_subscriber_source_network description this command is used to display the status of the igmp report/leave message source ip check. Format show igmp check_subscriber_source_network {ipif } pa...

  • Page 527

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 522 dgs-3620-28sc:admin# 41-6 create igmp static_group description this command is used to create an igmp static group on the switch. Format create igmp static_group ipif group parameters ipif – specifies the ip int...

  • Page 528

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 523 all – specifies that all the multicast ip addresses will be deleted. Restrictions only administrator, operator and power-user level users can issue this command. Example to delete the igmp static group, with the...

  • Page 529

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 524 dgs-3620-28sc:admin# show igmp static_group ipif n20 command: show igmp static_group ipif n20 interface multicast group ------------ --------------- n20 239.0.0.3 total entries: 1 dgs-3620-28sc:admin# to display...

  • Page 531

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 526 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable the igmp proxy: dgs-3620-28sc:admin#disable igmp_proxy command: disable igmp_proxy...

  • Page 532

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 527 command: config igmp_proxy downstream_if add vlan vlanid 2-7 success. Dgs-3620-28sc:admin# 42-4 config igmp_proxy upstream_if description this command is used to configure the setting for the igmp proxy’s upstre...

  • Page 533

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 528 success. Dgs-3620-28sc:admin# 42-5 show igmp_proxy description this command displays igmp proxy configuration information or group information on the switch. The display status item means group entry is determin...

  • Page 534

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 529 dest-v : the destination vlan. A : active i : inactive dest ip source ip dest-v member ports status ----------- ------------- ------ ---------------- --------- 224.2.2.2 null 4 3,6 a 2 2-4 i 227.3.1.5 null 2 2,5...

  • Page 536

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 531 vlanid - specifies the vlan id list. - enter the vlan id list. All - specifies to configure all vlans. State - enable or disable igmp snooping for the chosen vlan. Enable - enable igmp snooping for the chosen vl...

  • Page 537

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 532 - enter the amount of time in seconds between general query transmissions. The default setting is 125 seconds. Max_response_time - specifies the maximum time in seconds to wait for reports from members. - enter ...

  • Page 538

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 533 43-3 config router_ports description this command is used to designate a range of ports as being connected to multicast-enabled routers. This will ensure that all packets with such a router as its destination wi...

  • Page 539

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 534 add - specifies to add the router ports. Delete - specifies to delete the router ports. - enter a range of ports to be configured. Restrictions only administrator, operator and power-user level users can issue t...

  • Page 540

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 535 43-6 disable igmp_snooping description this command is used to disable igmp snooping on the switch. Igmp snooping can be disabled only if ip multicast routing is not being used. Disabling igmp snooping allows al...

  • Page 541

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 536 restrictions none. Example to show igmp snooping: dgs-3620-28sc:admin#show igmp_snooping command: show igmp_snooping igmp snooping global state : disabled vlan name : default query interval : 125 max response ti...

  • Page 542

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 537 - enter a range of ports to be configured. - (optional) specify the group ip address for which to view igmp snooping group information. Note: if no parameter is specified, the system will display all of the curr...

  • Page 544

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 539 example to display the igmp snooping rate limit for ports 1-2: dgs-3620-28sc:admin#show igmp_snooping rate_limit ports 1-2 command: show igmp_snooping rate_limit ports 1-2 port rate limit -------- ------------ 1...

  • Page 545

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 540 dgs-3620-28sc:admin# 43-12 config igmp_snooping static_group description this command is used to configure an igmp snooping static group on the switch. When a port is configured as a static member port, the igmp...

  • Page 547

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 542 command: show igmp_snooping static_group vlan id/name ip address static member ports --------------------------------------- -------------- -------------------- 1/default 239.1.1.1 9-10 total entries : 1 dgs-362...

  • Page 548

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 543 dropped by multicast vlan : 0 report & leave igmp v1 report : 0 igmp v2 report : 0 igmp v3 report : 0 igmp v2 leave : 0 total : 0 dropped by rate limitation : 0 dropped by max group limitation : 0 dropped by gro...

  • Page 549

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 544 dgs-3620-28sc:admin#clear igmp_snooping statistics counter command: clear igmp_snooping statistics counter success. Dgs-3620-28sc:admin# 43-17 show igmp_snooping forwarding description this command is used to di...

  • Page 551

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 546 43-19 config igmp access_authentication ports description this command is used to enable or disable the igmp access control function for the specified ports. If the igmp access control function is enabled and th...

  • Page 552

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 547 parameters all - specifies all ports to be displayed. - enter a range of ports to be displayed. Restrictions none. Example to display the igmp access control status for ports 1-4: dgs-3620-28sc:admin#show igmp a...

  • Page 553

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 548.

  • Page 555

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 550 - enter the remap priority (0 to 7) to be associated with the data traffic to be forwarded on the multicast vlan. None - if none is specified, the packet’s original priority will be used. The default setting is ...

  • Page 556

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 551 tag_member_port - specifies the tagged member port of the multicast vlan. - enter a range of ports to be configured. State - (optional) specify if the multicast vlan for a chosen vlan should be enabled or disabl...

  • Page 557

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 552 restrictions only administrator, operator and power-user level users can issue this command. Example to create an igmp snooping multicast group profile with the name “knicks”: dgs-3620-28sc:admin#create igmp_sno...

  • Page 558

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 553 44-5 delete igmp_snooping multicast_vlan_group_profile description this command is used to delete an existing igmp snooping multicast group profile on the switch. Specify a profile name to delete it. Format dele...

  • Page 559

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 554 if no parameter is specified, the system will display all multicast vlan group profiles. Restrictions none. Example to display all igmp snooping multicast vlan profiles: dgs-3620-28sc:admin#show igmp_snooping mu...

  • Page 560

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 555 restrictions only administrator, operator and power-user level users can issue this command. Example to add an igmp snooping profile to a multicast vlan group with the name “v1”: dgs-3620-28sc:admin#config igmp_...

  • Page 561

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 556 44-9 delete igmp_snooping multicast_vlan description this command is used to delete an igmp snooping multicast vlan. Format delete igmp_snooping multicast_vlan parameters - enter the name of the multicast vlan t...

  • Page 562

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 557 example to enable igmp snooping multicast vlan: dgs-3620-28sc:admin#enable igmp_snooping multicast_vlan command: enable igmp_snooping multicast_vlan success. Dgs-3620-28sc:admin# 44-11 disable igmp_snooping mult...

  • Page 563

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 558 parameters - (optional) specify the name of the multicast vlan to be displayed. If no parameter is specified, the system will display all multicast vlans. Restrictions none. Example to display all igmp snooping ...

  • Page 564

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 559 disable - the packet will be dropped. Restrictions only administrator, operator and power-user level users can issue this command. Example to configure the forwarding mode for igmp snooping multicast vlan unmatc...

  • Page 565

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 560

  • Page 567

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 562 dgs-3620-28sc:admin#show ipmc command: show ipmc interface name ip address multicast routing --------------- --------------- ----------------- system 10.90.90.90 inact n1 1.3.2.3 pim-sm n2 2.3.2.3 pim-sm-dm n3 3...

  • Page 568

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 563 dgs-3620-28sc:admin#show ipmc cache command: show ipmc cache ip multicast forwarding table multicast source upstream expire routing group address/netmask neighbor time protocol --------------- ------------------...

  • Page 570

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 565 dgs-3620-28sc:admin# create ip prefix_list 1 command: create ip prefix_list 1 success. Dgs-3620-28sc:admin# 46-2 config ip prefix_list description this command defines the rule entry for an ip route prefix list....

  • Page 571

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 566 - specifies the network address used. Ge - (optional) specifies the minimum prefix length to be matched. - enter the 'ge' value used here. This value must be between 1 and 32. Le - (optional) specifies the maxim...

  • Page 572

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 567 dgs-3620-28sc:admin# delete ip prefix_list list_name list1 command: delete ip prefix_list list_name list1 success. Dgs-3620-28sc:admin# 46-4 show ip prefix_list description this command is used to show an ip pre...

  • Page 573

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 568 parameters - enter the name of the access list used here. This name can be up to 16 characters long. Restrictions only administrator, operator and power-user level users can issue this command. Example to create...

  • Page 574

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 569 dgs-3620-28sc:admin# config ip standard access_list list1 add 10.10.10.0/24 permit command: config ip standard access_list list1 add 10.10.10.0/24 permit success. Dgs-3620-28sc:admin# 46-7 delete ip standard acc...

  • Page 575

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 570 parameters - (optional) enter the name of the access list used here. This name can be up to 16 characters long. If no parameter is specified, all access lists on the switch will be displayed. Restrictions none. ...

  • Page 576

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 571 dgs-3620-28sc:admin# clear ip prefix_list counter list_name 192.168.10.0/24 command: clear ip prefix_list counter list_name 192.168.10.0/24 success. Dgs-3620-28sc:admin# 46-10 create route_map description this c...

  • Page 578

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 573 - specifies the ip address to set. Peer_address - this will take effect for both the ingress and egress directions. When set to next_hop to peer address, for ingress direction, the next hop will be set to the ne...

  • Page 579

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 574 restrictions only administrator, operator and power-user level users can issue this command. Example to configure a route map named “map1” and add one sequence id of 20 to the route map: dgs-3620-28sc:admin# con...

  • Page 580

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 575 example to delete the route map named “map1”: dgs-3620-28sc:admin# delete route_map map_name map1 command: delete route_map map_name map1 success. Dgs-3620-28sc:admin# 46-13 show route_map description this comma...

  • Page 582

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 577 system. The first created is the primary, the second created is the backup. Weight - (optional) specifies the weight value of the ip route. - enter the weight value used here. This value must be between 1 and 4....

  • Page 584

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 579 47-4 create ipv6route description this command is used to create an ipv6 static route in the switch’s ip routing table. If the next hop is a global address, it is not necessary to indicate the interface name. If...

  • Page 586

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 581 example to display ipv6 route(s): dgs-3620-28sc:admin#show ipv6route command: show ipv6route ipv6 prefix: ::/0 protocol: static metric: 1 next hop : fec0::5 ipif : system total entries: 1 dgs-3620-28sc:admin# 47...

  • Page 587

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 582 format disable ecmp ospf parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable the ospf ecmp function: dgs-3620-28sc:admin# disable ecmp...

  • Page 588

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 583 example to set the ecmp hash algorithm: dgs-3620-28sc:admin# config ecmp algorithm ip_destination ip_source command: config ecmp algorithm ip_destination ip_source success. Dgs-3620-28sc:admin# 47-10 show ecmp a...

  • Page 590

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 585 restrictions only administrator, operator and power-user level users can issue this command. (ei mode only command) example to configure the ripng route redistribution: dgs-3620-28sc:admin#config ipv6route redis...

  • Page 591

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 586 47-14 create ipv6route redistribute dst ospfv3 src description this command is used to create a new ipv6 route redistribution to import route of other protocol into ospfv3. Format create ipv6route redistribute d...

  • Page 593

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 588 ripng - specifies to stop redistributing ripng routes into ospfv3. Restrictions only administrator, operator and power-user level users can issue this command. (ei mode only command) example to remove ospfv3 rou...

  • Page 595

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 590 48-2 delete ip_tunnel description this command is used to delete an ip tunnel interface. Format delete ip_tunnel parameters - enter the ip tunnel interface name used here. This name can be up to 12 characters lo...

  • Page 596

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 591 configured. The ipv6 address is not connected with the tunnel source or the destination ipv4 address. - enter the ipv6 address used here. Source - (optional) specifies the source ipv4 address of the ipv6 tunnel ...

  • Page 597

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 592 parameters - enter the ip tunnel interface name used here. This name can be up to 12 characters long. Ipv6address - (optional) specifies the ipv6 address assigned to this ipv6 tunnel interface. Ipv6 processing w...

  • Page 599

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 594 parameters - (optional) enter the ip tunnel interface name used here. This name can be up to 12 characters long. Restrictions none. (ei mode only command) example to show an ip tunnel interface’s information (tu...

  • Page 600

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 595 dgs-3620-28sc:admin# enable ip_tunnel tn2 command: enable ip_tunnel tn2 success. Dgs-3620-28sc:admin# 48-8 disable ip_tunnel description this command is used to disable a single specified ip tunnel or all ip tun...

  • Page 601

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 596 when a user wants to configure a gre ipv6/ipv4-in-ipv6 tunnel, both the source and destination address must be ipv6 addresses because the delivery protocol is the ipv6 protocol. If the source and destination add...

  • Page 602

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 597 dgs-3620-28sc:admin# config ip_tunnel gre tn1 source 1.0.0.1 destination 1.0.0.2 command: config ip_tunnel gre tn1 source 1.0.0.1 destination 1.0.0.2 success. Dgs-3620-28sc:admin# config ip_tunnel gre tn1 ipaddr...

  • Page 603

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 598 dgs-3620-28sc:admin# show ip_tunnel tn2 command: show ip_tunnel tn2 tunnel interface : tn2 interface admin state : enabled tunnel mode : gre ipv4 address : 3.0.0.1/8 ipv6 address : 3001::1/64 tunnel source : 200...

  • Page 605

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 600 49-2 delete ipv6 neighbor_cache ipif description this command is used to delete a neighbor cache entry or static neighbor cache entries from the address cache or all address cache entries on this ip interface. B...

  • Page 606

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 601 - enter the ipv6 address static - specifies to display the ipv6 static neighbor cache entries. Dynamic - specifies to display the ipv6 dynamic entries. All - specifies to display all ipv6 addresses, static and d...

  • Page 607

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 602 example to configure the ns retransmit time of a specified interface: dgs-3620-28sc:admin#config ipv6 nd ns ipif system retrans_time 400 command: config ipv6 nd ns ipif system retrans_time 400 success. Dgs-3620-...

  • Page 608

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 603 max_rtr_adv_interval - specifies the maximum time allowed between sending unsolicited multicast router advertisements from the interface, in seconds. It must be no less than 4 seconds and no greater than 1800 se...

  • Page 609

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 604 disable - when set to disable, the specified prefix will not be used to create an autonomous address configuration. Restrictions only administrator, operator and power-user level users can issue this command. Ex...

  • Page 610

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 605 ns retransmit time : 400 (ms) router advertisement : disabled ra max router advinterval : 600 (sec) ra min router advinterval : 198 (sec) ra router life time : 1800 (sec) ra reachable time : 1200000 (ms) ra retr...

  • Page 613

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 608 - enter a range of ports to be configured. All - specifies to apply to all the ports. Restrictions only administrator, operator and power-user level users can issue this command. Example to create a static ipv6 ...

  • Page 614

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 609 loose - specifies that in this mode, all packets are forwarded by default until an illegal arp or broadcast ip packet is detected. Disable - disable the arp inspection function. The default value is disable. Ip_...

  • Page 615

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 610 parameters - enter the ip address. Mac_address - specifies the mac address. - enter the mac address here. Ports - (optional) configure the portlist to apply, if ports are not configured, then it will apply to al...

  • Page 616

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 611 example to configure a static ipv6 impb entry so that that ipv6 address fe80::240:5ff:fe00:28 is bound to the mac address 00-00-00-00-00-11: dgs-3620-28sc:admin# config address_binding ip_mac ipv6address fe80::2...

  • Page 618

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 613 format show address_binding {ports {}} parameters ports – (optional) specify to display the state of ip mac port binding for all ports. - enter the list of ports for the display here. Restrictions none. Example ...

  • Page 621

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 616 00-00-00-00-00-11 command: show address_binding ip_mac ipaddress 10.1.1.1 mac_address 00-00-00- 00-00-11 m(mode) – d:dhcp,n:nd,s:static acl - a:active i:inactive ip address mac address m acl ports --------------...

  • Page 622

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 617 format disable address_binding trap_log parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable the address binding trap and log: dgs-3620...

  • Page 624

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 619 dgs-3620-28sc:admin# 50-15 clear address_binding dhcp_snoop binding_entry ports description this command is used to clear the address binding entries learned for the specified ports. Format clear address_binding...

  • Page 625

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 620 example to display address binding dhcp snooping: dgs-3620-28sc:admin#show address_binding dhcp_snoop command: show address_binding dhcp_snoop dhcp snoop(ipv4) : disabled dhcp snoop(ipv6) : disabled dgs-3620-28s...

  • Page 626

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 621 example to display the dhcp snooping binding entries: dgs-3620-28sc:admin#show address_binding dhcp_snoop binding_entry command: show address_binding dhcp_snoop binding_entry s (status) - a: active, i: inactive ...

  • Page 627

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 622 10 command: config address_binding dhcp_snoop max_entry ports 1-3 limit 10 success. Dgs-3620-28sc:admin# 50-19 config address_binding recover_learning ports description this command is used to recover port learn...

  • Page 628

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 623 restrictions only administrator, operator and power-user level users can issue this command. Example to enable the nd snooping function on the switch: dgs-3620-28sc:admin# enable address_binding nd_snoop command...

  • Page 630

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 625 dgs-3620-28sc:admin# show address_binding nd_snoop command: show address_binding nd_snoop nd snoop : enabled dgs-3620-28sc:admin# to show the nd snooping maximum entry information for ports 1-5: dgs-3620-28sc:ad...

  • Page 631

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 626 dgs-3620-28sc:admin# show address_binding nd_snoop binding_entry command: show address_binding nd_snoop binding_entry s (status) - a: active, i: inactive time - left time (sec) ip address mac address s lt(sec) p...

  • Page 633

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 628 example to enable impb roaming: dgs-3620-28sc:admin#enable address_binding roaming command: enable address_binding roaming success. Dgs-3620-28sc:admin# 50-28 disable address_binding roaming description this com...

  • Page 635

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 630 restrictions only administrator, operator and power-user level users can issue this command. Example to upload the dhcp snooping binding table: dgs-3620-28sc:admin#upload address_binding snoop_entry_totftp 10.90...

  • Page 636: Chapter 51

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 631 chapter 51 japanese web- based access control (jwac) commands enable jwac disable jwac enable jwac redirect disable jwac redirect enable jwac forcible_logout disable jwac forcible_logout enable jwac udp_filterin...

  • Page 637

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 632 using the jwac function, pc users need to pass two stages of authentication. The first stage is to do the authentication with the quarantine server and the second stage is the authentication with the switch. For...

  • Page 638

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 633 dgs-3620-28sc:admin#disable jwac command: disable jwac success. Dgs-3620-28sc:admin# 51-3 enable jwac redirect description this command is used to enable jwac redirect. When redirect quarantine_server is enabled...

  • Page 639

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 634 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable jwac redirect: dgs-3620-28sc:admin#disable jwac redirect command: disable jwac red...

  • Page 640

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 635 51-6 disable jwac forcible_logout description this command is used to disable jwac forcible logout. Format disable jwac forcible_logout parameters none. Restrictions only administrator, operator and power-user l...

  • Page 641

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 636 example to enable jwac udp filtering: dgs-3620-28sc:admin#enable jwac udp_filtering command: enable jwac udp_filtering success. Dgs-3620-28sc:admin# 51-8 disable jwac udp_filtering description this command is us...

  • Page 642

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 637 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to enable jwac quarantine server monitoring: dgs-3620-28sc:admin#enable jwac quarantine_serve...

  • Page 643

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 638 51-11 config jwac quarantine_server_error_timeout description this command is used to set the quarantine server error timeout. When the quarantine server monitor is enabled, the jwac switch will periodically che...

  • Page 644

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 639 parameters quarantine_server_url - specifies the entire url of the authentication page on the quarantine server. - enter the entire url of the authentication page on the quarantine server. The quarantine server ...

  • Page 645

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 640 example to configure jwac redirect destination to jwac login web page and a delay time of 5 seconds: dgs-3620-28sc:admin#config jwac redirect destination jwac_login_page delay_time 5 command: config jwac redirec...

  • Page 646

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 641 need to be able to have access to accomplish authentication. Before the client passes authentication, it should be added to the switch with its ip address. For example, the client may need to access update.Micro...

  • Page 647

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 642 parameters - enter a tcp port which the jwac switch listens to and uses to finish the authenticating process. Http - (optional) specify the jwac run http protocol on this tcp port. Https - (optional) specify the...

  • Page 648

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 643 block_time - if a host fails to pass the authentication, it will be blocked for a period specified by the blocking time.The default value is 60 seconds. - enter a blocking time value between 0 and 300. Restricti...

  • Page 649

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 644 dgs-3620-28sc:admin# 51-19 create jwac user description this command creates jwac users in the local database. When “local” is chosen while configuring the jwac radius protocol, the local database will be used. ...

  • Page 650

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 645 account to pass authentication. - enter the target vlan id for the authenticated host which uses this user account to pass authentication. The vlan id value must be between 1 and 4094. Restrictions only administ...

  • Page 651

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 646 51-22 show jwac user description this command is used to display jwac users in the local database. Format show jwac user parameters none. Restrictions none. Example to display the current jwac local users: dgs-3...

  • Page 652

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 647 restrictions none. Example to display the current jwac configuration: dgs-3620-28sc:admin#show jwac command: show jwac state : disabled enabled ports : virtual ip/url : 0.0.0.0/- switch http port : 80 (http) udp...

  • Page 653

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 648 example to display jwac authentication entries for ports 1 to 2: dgs-3620-28sc:admin#show jwac auth_state ports 1-2 command: show jwac auth_state ports 1-2 pri:priority. State – a:authenticated. B:bloacked. -:au...

  • Page 654

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 649 3 172.18.0.0/21 tcp 3 active dgs-3620-28sc:admin# 51-26 show jwac ports description this command is used to display the port configuration of jwac. Format show jwac ports {} parameters - (optional) specify a por...

  • Page 655

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 650 parameters ports - specifies the port range to delete hosts on. All - specifies to delete all ports. - enter range of ports to delete. Authenticated - (optional) specify the state of host to delete. Authenticati...

  • Page 656

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 651 dgs-3620-28sc:admin# 51-29 show jwac authenticate_page description this command is used to display the element mapping of the customized authenticate page. Format show jwac authenticate_page parameters none. Res...

  • Page 658

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 653 user_name_title ユーザ名 command: config jwac authentication_page element japanese user_name_title ユーザ 名 success. Dgs-3620-28sc:admin# config jwac authentication_page element japanese password_title パスワード command: c...

  • Page 659

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 654 example to disable the configuration authorized from the local database: dgs-3620-28sc:admin#config jwac authorization attributes local disable command: config jwac authorization attributes local disable success...

  • Page 661

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 656 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable jumbo frames: dgs-3620-28sc:admin#disable jumbo_frame command: disable jumbo_frame...

  • Page 662

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 657 52-4 show jumbo_frame description this command is used to display jumbo frames. Format show jumbo_frame {} parameters - (optional) enter the list of ports to be displayed here. Restrictions none. Example to disp...

  • Page 664

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 659 53-2 show lacp_port description this command is used to display per-port lacp mode. Format show lacp_port {} parameters - (optional) specify a range of ports to be displayed. Note: if no parameter is specified, ...

  • Page 666

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 661 threshold - (optional) specify the drop threshold for packets-per-second accepted on this uni port. The port drops the pdu if the protocol’s threshold is exceeded. The range of the threshold value is 0 to 65535 ...

  • Page 667

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 662 dgs-3620-28sc:admin# show l2protocol_tunnel command: show l2protocol_tunnel global state: enabled uni ports: 1-2 nni ports: 3-4 dgs-3620-28sc:admin# to show layer 2 protocol tunneling detail information on uni p...

  • Page 668

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 663 format enable l2protocol_tunnel parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to enable the layer 2 protocol tunneling function: dgs-3620-2...

  • Page 669

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 664 dgs-3620-28sc:admin# disable l2protocol_tunnel command: disable l2protocol_tunnel success. Dgs-3620-28sc:admin#.

  • Page 671

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 666 success. Dgs-3620-28sc:admin# 55-2 config mcast_filter_profile description this command is used to modify the profile name, add or delete a range of previously defined multicast ip addresses to or from the profi...

  • Page 673

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 668 all - all multicast address profiles will be deleted. Profile_name - specifies a profile based on the profile name. - the profile name can be up to 32 characters long. Restrictions only administrator, operator a...

  • Page 674

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 669 example to display all the defined multicast address profiles: dgs-3620-28sc:admin#show mcast_filter_profile command: show mcast_filter_profile profile id name multicast addresses ---------- --------------------...

  • Page 675

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 670 - the profile name can be up to 32 characters long. Access - (optional) specify whether the access is permit or deny. Permit - specifies that the packets that match the addresses defined in the profiles will be ...

  • Page 676

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 671 vlan : 1 access : deny profile id name multicast addresses ----------- ----------- ----------------------------- 1 customer 224.19.62.34 – 224.19.162.200 dgs-3620-28sc:admin# to display the limited multicast add...

  • Page 677

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 672 vlanid - specifies the vlan id to configure the maximum multicast group. - enter the vlan id of the vlan here. Ipv4 - (optional) specify that the maximum number of ipv4 learned addresses should be limited. Ipv6 ...

  • Page 678

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 673 dgs-3620-28sc:admin# show max_mcast_group ports 1-2 command: show max_mcast_group ports 1-2 port max multicast group number action ----- --------------------------- --------- 1 infinite drop 2 infinite drop tota...

  • Page 680

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 675 56-2 delete link_aggregation group_id description this command is used to delete a previously configured link aggregation group. Format delete link_aggregation group_id parameters - enter the group id. Restricti...

  • Page 681

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 676 the group type is lacp, the ports’ state machine will start. Enable - enable the specified link aggregation group. Disable - disable the specified link aggregation group. Trap - specifies the trap status for a l...

  • Page 682

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 677 l4_src_port - indicate that the switch should examine the layer 4 source port. L4_dest_port - indicate that the switch should examine the layer 4 destination port. L4_src_dest_port - indicate that the switch sho...

  • Page 683

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 678 group id : 1 type : lacp master port : 1:5 member port : 1:5-1:8 active port : status : enabled flooding port : trap : enabled total entries : 1 dgs-3620-28sc:admin# to display the current link aggregation confi...

  • Page 685

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 680 restrictions only administrator, operator and power-user level users can issue this command. Example to enable lldp: dgs-3620-28sc:admin#enable lldp command: enable lldp success. Dgs-3620-28sc:admin# 57-2 disabl...

  • Page 686

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 681 the ttl will be carried in the lldpdu packet. The lifetime will be the minimum of 65535 and (message_tx_interval * message_tx_hold_multiplier). On the partner switch, when the time-to-live for a given advertisem...

  • Page 687

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 682 dgs-3620-28sc:admin#config lldp tx_delay 8 command: config lldp tx_delay 8 success. Dgs-3620-28sc:admin# to change the re-initialization delay interval to five seconds: dgs-3620-28sc:admin#config lldp reinit_del...

  • Page 688

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 683 message tx hold multiplier: 4 reinit delay : 2 tx delay : 2 notification interval : 5 dgs-3620-28sc:admin# 57-5 config lldp forward_message description this command is used to configure lldp forwarding messages....

  • Page 689

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 684 parameters - enter the notification interval range is from 5 to 3600 seconds. The default setting is 5 seconds. Restrictions only administrator, operator and power-user level users can issue this command. Exampl...

  • Page 690

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 685 configure an individual port or group of ports to exclude one or more of ieee 802.1 organizationally protocol identity tlv data types from outbound lldp advertisements. This tlv optional data type indicates whet...

  • Page 691

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 686 agent should transmit “system description tlv.” the default state is disabled. System_capabilities - (optional) this tlv optional data type includes indicates that lldp agent should transmit “system capabilities...

  • Page 692

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 687 advertisements. Dot3_tlvs - an individual port or group of ports to exclude one or more of ieee 802.3 organizationally specific tlv data types from outbound lldp advertisements. All – (optional) configure all of...

  • Page 693

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 688 success. Dgs-3620-28sc:admin# to exclude the system name tlv from the outbound lldp advertisements for all ports: dgs-3620-28sc:admin#config lldp ports all basic_tlvs system_name enable command: config lldp port...

  • Page 694

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 689 to exclude the mac/phy configuration/status tlv from the outbound lldp advertisements for all ports: dgs-3620-28sc:admin#config lldp ports all dot3_tlvs mac_phy_configuration_status enable command: config lldp p...

  • Page 695

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 690 dgs-3620-28sc:admin#show lldp ports 1 command: show lldp ports 1 port id : 1 -------------------------------------------------------------- admin status : tx_and_rx notification status : disabled advertised tlvs...

  • Page 696

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 691 dgs-3620-28sc:admin#config lldp_med fast_start repeat_count 5 command: config lldp_med fast_start repeat_count 5 success. Dgs-3620-28sc:admin# 57-10 config lldp_med log state description this command is used to ...

  • Page 697

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 692 all - specifies to set all ports in the system. State - enable or disable the snmp trap notification of topology change detected state. Enable - enable the snmp trap notification of topology change detected. Dis...

  • Page 698

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 693 restrictions only administrator and operator-level users can issue this command. Example to enable transmitting of all capabilities on ports 1 to 2: dgs-3620-28sc:admin#config lldp_med ports 1-2 med_transmit_cap...

  • Page 699

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 694 dgs-3620-28sc:admin# 57-14 show lldp_med description this command is used to display the switch’s general lldp-med configuration status. Format show lldp_med parameters none. Restrictions none. Example to displa...

  • Page 700

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 695 57-15 show lldp_med local_ports description this command is used to display the per-port lldp-med information currently available for populating outbound lldp-med advertisements. Format show lldp_med local_ports...

  • Page 701

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 696 format show lldp_med remote_ ports {} parameters - (optional) specify a range of ports to be displayed. Note: when a port list is not specified, information for all ports will be displayed. Restrictions none. Ex...

  • Page 702

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 697 unknown : true tagged : application type : softphone voice vlan id : 200 priority : 7 dscp : 5 unknown : false tagged : true location identification: location subtype: coordinatebased location information : loca...

  • Page 703

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 698 restrictions none. Example to display lldp local port information for port 1: dgs-3620-28sc:admin#show lldp local_ports 1 command: show lldp local_ports 1 port id : 1 --------------------------------------------...

  • Page 704

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 699 dgs-3620-28sc:admin#show lldp mgt_addr command: show lldp mgt_addr address 1 : ------------------------------------------------------ subtype : ipv4 address : 10.19.72.38 if type : unknown oid : 1.3.6.1.4.1.171....

  • Page 705

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 700 57-20 show lldp statistics description this command is used to display an overview of neighbor detection activity on the switch. Format show lldp statistics parameters none. Restrictions none. Example to display...

  • Page 706

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 701 restrictions none. Example to display lldp statistic information for port 1: dgs-3620-28sc:admin#show lldp statistics ports 1 command: show lldp statistics ports 1 port id : 1 -----------------------------------...

  • Page 708

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 703 dgs-3620-28sc:admin#config loopdetect recover_timer 0 interval 20 mode vlan- based command: config loopdetect recover_timer 0 interval 20 mode vlan-based success. Dgs-3620-28sc:admin# 58-2 config loopdetect port...

  • Page 709

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 704 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to enable loop detection: dgs-3620-28sc:admin#enable loopdetect command: enable loopdetect su...

  • Page 710

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 705 58-5 show loopdetect description this command is used to display the switch’s current loop detection configuration. Format show loopdetect parameters none. Restrictions none. Example to display the switch’s curr...

  • Page 711

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 706 restrictions none. Example to display the loop detection state of ports 1 to 9 in port-based mode: dgs-3620-28sc:admin#show loopdetect ports 1-9 command: show loopdetect ports 1-9 port loopdetect state loop stat...

  • Page 716

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 711 example to show the information of the loopback interface named loopback1: dgs-3620-28sc:admin#show loopback ipif loopback1 command: show loopback ipif loopback1 loopback interface : loopback1 interface admin st...

  • Page 718

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 713 format disable mac_notification parameters none. Restrictions only administrator and operator-level users can issue this command. Example to disable the mac notification function: dgs-3620-28sc:admin#disable mac...

  • Page 719

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 714 dgs-3620-28sc:admin#config mac_notification interval 1 historysize 500 command: config mac_notification interval 1 historysize 500 success. Dgs-3620-28sc:admin# 60-4 config mac_notification ports description thi...

  • Page 720

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 715 restrictions none. Example to show the switch’s mac address table notification global settings: dgs-3620-28sc:admin#show mac_notification command: show mac_notification global mac notification settings state : e...

  • Page 721

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 716 dgs-3620-28sc:admin#show mac_notification ports command: show mac_notification ports port # mac address table notification state ------ ------------------------------------ 1 disabled 2 disabled 3 disabled 4 dis...

  • Page 723

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 718 example to enable mac-based access control: dgs-3620-28sc:admin#enable mac_based_access_control command: enable mac_based_access_control success. Dgs-3620-28sc:admin# 61-2 disable mac_based_access_control descri...

  • Page 724

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 719 parameters - in radius mode, the switch communicates with the radius server using this password. The maximum length of the key is 16 characters. Restrictions only administrator, operator and power-user level use...

  • Page 725

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 720 61-5 config mac_based_access_control guest_vlan ports description this command is used to put the specified port in guest vlan mode. For those ports not contained in the port list, they are in non-guest vlan mod...

  • Page 727

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 722 parameters guest_vlan - specifies the name of the guest vlan. - enter the name of the guest vlan. The guest vlan name can be up to 32 characters long. Guest_vlanid - specifies the vlan id of the guest vlan. - en...

  • Page 728

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 723 success. Dgs-3620-28sc:admin# 61-9 clear mac_based_access_control auth_state description this command is used to clear the authentication state of a user (or port). The port (or the user) will return to un-authe...

  • Page 729

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 724 parameters - enter the mac address that access accepts by local mode. Vlan - (optional) if the mac address is authorized, the port will be assigned to this vlan. - enter a vlan name up to 32 characters long. Vla...

  • Page 730

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 725 command: config mac_based_access_control_local mac 00-00-00-00-00-01 vlan default success. Dgs-3620-28sc:admin# 61-12 config mac_based_access_control max_users description this command is used to configure the m...

  • Page 731

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 726 parameters radius - specifies to enable or disable the authorized attributes assigned by the radius server that will be accepted. Enable - if specified to enable, the authorized attributes (for example vlan, 802...

  • Page 732

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 727 restrictions only administrator, operator and power-user level users can issue this command. Example to delete a mac-based access control local by mac address: dgs-3620-28sc:admin#delete mac_based_access_control...

  • Page 733

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 728 dgs-3620-28sc:admin# show mac_based_access_control auth_state ports command: show mac_based_access_control auth_state ports (p): port-based prio: priority port mac address original state vid prio aging time/ rx ...

  • Page 734

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 729 guest vlan : guest vlan member ports: radius authorization : enabled local authorization : enabled trap state : enabled log state : enabled dgs-3620-28sc:admin# to display mac-based access control information fo...

  • Page 735

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 730 dgs-3620-28sc:admin#show mac_based_access_control_local command: show mac_based_access_control_local mac address vid ----------------- ------ 00-00-00-00-00-01 1 total entries:1 dgs-3620-28sc:admin# to display m...

  • Page 736

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 731 restrictions only administrator, operator and power-user level users can issue this command. Example to disable the log state for mac-based access control: dgs-3620-28sc:admin# config mac_based_access_control lo...

  • Page 738: Chapter 62

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 733 chapter 62 md5 configuration command list config md5 key create md5 key delete md5 key show md5 {key } 62-1 config md5 key description this command is used to configure an md5 key and password. The md5 configura...

  • Page 739

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 734 format create md5 key parameters key - specifies that the md5 key will be created. - enter the md5 key used here. This key must be between 1 and 255. - enter an alphanumeric string of between 1 and 16, case-sens...

  • Page 740

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 735 dgs-3620-28sc:admin# delete md5 key 1 command: delete md5 key 1 success. Dgs-3620-28sc:admin# 62-4 show md5 description this command is used to display the md5 key table. Format show md5 {key } parameters key - ...

  • Page 743

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 738 delete - (optional) specifies the mirror source ports to be delete source - (optional) specifies the source ports used. Ports - (optional) specifies the list of ports used as source ports. - enter the list of po...

  • Page 744

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 739 dgs-3620-28sc:admin# delete mirror group_id 3 command: delete mirror group_id 3 success. Dgs-3620-28sc:admin# 63-5 enable mirror description this command, combined with the disable mirror command below, allows y...

  • Page 745

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 740 parameters none. Restrictions only administrator and operator-level users can issue this command. Example to disable mirroring configurations: dgs-3620-28sc:admin#disable mirror command: disable mirror success. ...

  • Page 746

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 741 dgs-3620-28sc:admin#show mirror command: show mirror mirror global state: disabled group state target port source ports ------- ---------- ------------- --------------------------------------------- - 1 enabled ...

  • Page 748

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 743 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable the mld proxy: dgs-3620-28sc:admin#disable mld_proxy command: disable mld_proxy su...

  • Page 749

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 744 success. Dgs-3620-28sc:admin# 64-4 config mld_proxy upstream_if description this command is used to configure the setting for the mld proxy’s upstream interface. The mld proxy plays the host role on the upstream...

  • Page 750

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 745 64-5 show mld_proxy description this command is used to display the mld proxy’s configuration or group information. The display status item means group entry is determined by whether or not the chip has been ins...

  • Page 751

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 746 source : ff80::200 group : ff1e::0202 downstream vlan : 2 member ports : 2,5,8 status : inactive total entries: 2 dgs-3620-28sc:admin#.

  • Page 753

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 748 vlanid - specifies the vlan id list. - enter the vlan id list. All - specifies to configure all vlans. State - enable or disable mld snooping for the chosen vlan. Enable - enable mld snooping for the chosen vlan...

  • Page 754

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 749 restrictions only administrator, operator and power-user level users can issue this command. Example to configure the mld snooping packet rate limit on port 1 for 100: dgs-3620-28sc:admin#config mld_snooping rat...

  • Page 755

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 750 65-4 create mld_snooping static_group description this command is used to create an mld snooping multicast static group. Member ports can be added to the static group. The static member and the dynamic member po...

  • Page 757

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 752 example to delete an mld snooping static group from the default vlan, group ff1e::1: dgs-3620-28sc:admin#delete mld_snooping static_group vlan default ff1e::1 command: delete mld_snooping static_group vlan defau...

  • Page 758

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 753 65-8 show mld_snooping statistic counter description this command is used to display the mld snooping statistics counters for mld protocol packets that are transmitted or received by the switch since mld snoopin...

  • Page 759

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 754 dgs-3620-28sc:admin#show mld_snooping statistic counter ports 1 command: show mld_snooping statistic counter ports 1 port # : 1 -------------------------------------------------- group number : 0 receive statist...

  • Page 760

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 755 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to clear the mld snooping statistics counters: dgs-3620-28sc:admin#clear mld_snooping statist...

  • Page 761

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 756 2. Other querier present interval—amount of time that must pass before a multicast router decides that there is no longer another multicast router that is the querier. This interval is calculated as follows: (ro...

  • Page 762

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 757 parameters vlan - specifies the name of the vlan on which the router port resides. - enter the name of the vlan on which the router port resides. The maximum length is 32 characters. Vlanid - specifies the id of...

  • Page 763

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 758 example to set up ports as forbidden router port: dgs-3620-28sc:admin#config mld_snooping mrouter_ports_forbidden vlan default add 1-10 command: config mld_snooping mrouter_ports_forbidden vlan default add 1-10 ...

  • Page 764

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 759 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable mld snooping on the switch: dgs-3620-28sc:admin#disable mld_snooping command: disa...

  • Page 765

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 760 vlan name : default query interval : 125 max response time : 10 robustness value : 2 last listener query interval : 1 querier state : disabled querier role : non-querier querier ip : :: querier expiry time : 0 s...

  • Page 766

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 761 example to display the mld snooping group: dgs-3620-28sc:admin#show mld_snooping group command: show mld_snooping group source/group : 2001::1/fe1e::1 vlan name/vid :default/1 member ports : 1-2 up time : 26 exp...

  • Page 767

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 762 note: if no parameter is specified, the system will display all router ports on the switch. Restrictions none. Example to display router ports: dgs-3620-28sc:admin#show mld_snooping mrouter_ports all command: sh...

  • Page 768

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 763 example to display all mld snooping forwarding entries located on the switch: dgs-3620-28sc:admin#show mld_snooping forwarding command: show mld_snooping forwarding vlan name : default source ip : 2001::1 multic...

  • Page 770

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 765 forwarded on the multicast vlan. None - if none is specified, the packet’s original priority will be used. The default setting is none. Replace_priority - (optional) specify that the packet’s priority will be ch...

  • Page 771

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 766 - enter a range of ports to be configured. State - specifies if the multicast vlan for a chosen vlan should be enabled or disabled. Enable - enable multicast vlan for the chosen vlan. Disable - disable multicast...

  • Page 772

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 767 example to create an mld snooping multicast group profile with the name “knicks”: dgs-3620-28sc:admin#create mld_snooping multicast_vlan_group_profile knicks command: create mld_snooping multicast_vlan_group_pro...

  • Page 773

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 768 66-5 delete mld_snooping multicast_vlan_group_profile description this command is used to delete an existing mld snooping multicast group profile on the switch. Specify a profile name to delete it. Format delete...

  • Page 774

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 769 restrictions none. Example to display all mld snooping multicast vlan profiles: dgs-3620-28sc:admin#show mld_snooping multicast_vlan_group_profile command: show mld_snooping multicast_vlan_group_profile profile ...

  • Page 775

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 770 example to add an mld snooping profile to a multicast vlan group with the name “v1”: dgs-3620-28sc:admin#config mld_snooping multicast_vlan_group v1 add profile_name channel_1 command: config mld_snooping multic...

  • Page 776

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 771 66-9 delete mld_snooping multicast_vlan description this command is used to delete an mld snooping multicast vlan. Format delete mld_snooping multicast_vlan parameters - enter the name of the multicast vlan to b...

  • Page 777

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 772 dgs-3620-28sc:admin#enable mld_snooping multicast_vlan command: enable mld_snooping multicast_vlan success. Dgs-3620-28sc:admin# 66-11 disable mld_snooping multicast_vlan description this command is used to disa...

  • Page 778

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 773 if no parameter is specified, the system will display all multicast vlans on the switch. Restrictions none. Example to display all mld snooping multicast vlans: dgs-3620-28sc:admin#show mld_snooping multicast_vl...

  • Page 779

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 774 restrictions only administrator, operator and power-user level users can issue this command. Example to configure the forwarding mode for mld snooping multicast vlan unmatched packets: dgs-3620-28sc:admin#config...

  • Page 781

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 776 =============================================================================== ctrl+c quit without save left/right/ ctrl+w save and quit up/down move cursor ctrl+d delete line ctrl+x erase all setting ctrl+l re...

  • Page 782

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 777 dgs-3620-28sc:admin#show greeting_message command: show greeting_message =============================================================================== dgs-3620-28sc gigabit ethernet switch command line interfa...

  • Page 783

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 778 restrictions when users issue the “reset” command, the current command prompt will remain in tact. Issuing the “reset system” will return the command prompt to its original factory default value. Only administra...

  • Page 785

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 780 disable - specifies that the mld state for the specified interface will be disabled. Restrictions only administrator, operator and power-user level users can issue this command. Example to configure the mld on t...

  • Page 786

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 781 restrictions none. Example to display the mld configurations on all interfaces: dgs-3620-28sc:admin# show mld command: show mld mld interface configurations mrt = maximum response time, llqi = last listener quer...

  • Page 788

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 783 dgs-3620-28sc:admin# show mld group ipif n10 command: show mld group ipif n10 interface multicast group expiry ------------ ------------------ ----- n10 ff1e::1001:1234 255 n10 ff1e::5a3d:11:23c1 260 total entri...

  • Page 789

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 784 dgs-3620-28sc:admin# show mld group group ff1e::1001:1234 command: show mld group group ff1e::1001:1234 interface multicast group expiry ------------ ------------------ ----- n10 ff1e::1001:1234 215 n11 ff1e::10...

  • Page 791

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 786 dgs-3620-28sc:admin# create nlb multicast_fdb default 03-bf-01-01-01-01 command: create nlb multicast_fdb default 03-bf-01-01-01-01 success. Dgs-3620-28sc:admin# 69-2 delete nlb multicast_fdb description this co...

  • Page 792

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 787 parameters - enter the vlan name of the nlb multicast fdb entry here. This name can be up to 32 characters long. Vlanid - specifies the vlan id used. - enter the vlan id used here. - specifies the mac address of...

  • Page 793

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 788 dgs-3620-28sc:admin# show nlb fdb command: show nlb fdb mac address vlan id egress ports ----------------- ---------- ---------------------------------- 02-bf-01-01-01-01 - 1:1-1:5,1:26,2:26 02-bf-01-01-01-02 - ...

  • Page 795

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 790 dgs-3620-28sc:admin#delete nlb unicast_fdb 02-bf-01-01-01-01 command: delete nlb unicast_fdb 02-bf-01-01-01-01 success. Dgs-3620-28sc:admin#.

  • Page 797

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 792 restrictions only administrator and operator-level users can issue this command. Example to enable snmp: dgs-3620-28sc:admin#enable snmp command: enable snmp success. Dgs-3620-28sc:admin# 70-2 disable snmp descr...

  • Page 798

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 793 format show snmp parameters none. Restrictions none. Example to display snmp: dgs-3620-28sc:admin#show snmp command: show snmp system name : system location : system contact : snmp trap : enabled snmp state : di...

  • Page 799

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 794 snmp - (optional) specify the trusted host for snmp. Telnet - (optional) specify the trusted host for telnet. Ssh - (optional) specify the trusted host for ssh. Http - (optional) specify the trusted host for htt...

  • Page 800

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 795 all - specifies the trusted host for all applications. Restrictions only administrator and operator-level users can issue this command. Example to configure the trusted host: dgs-3620-28sc:admin#config trusted_h...

  • Page 801

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 796 dgs-3620-28sc:admin# 70-7 show trusted_host description this command is used to display the trusted hosts. Format show trusted_host parameters none. Restrictions none. Example to display trusted hosts: dgs-3620-...

  • Page 802

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 797 parameters - enter an snmp system name for the switch. A maximum of 255 characters is allowed. Restrictions only administrator and operator-level users can issue this command. Example to configure the switch snm...

  • Page 803

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 798 70-10 config snmp system_contact description this command is used to enter the name and/or other information to identify an snmp system contact person who is responsible for the switch. A maximum of 255 characte...

  • Page 804

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 799 dgs-3620-28sc:admin#enable snmp traps command: enable snmp traps success. Dgs-3620-28sc:admin# 70-12 disable snmp traps description this command is used to disable snmp trap support on the switch. Format disable...

  • Page 805

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 800 restrictions only administrator and operator-level users can issue this command. Example to enable snmp authentication trap support: dgs-3620-28sc:admin#enable snmp authenticate_traps command: enable snmp authen...

  • Page 806

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 801 parameters none. Restrictions only administrator and operator-level users can issue this command.. Example to enable snmp linkchange trap support: dgs-3620-28sc:admin#enable snmp linkchange_traps command: enable...

  • Page 807

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 802 70-17 config snmp linkchange_traps ports description this command is used to configure the sending of linkchange traps and per port control for sending of change traps. Format config snmp linkchange_traps ports ...

  • Page 808

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 803 example to display snmp traps: dgs-3620-28sc:admin#show snmp traps command: show snmp traps snmp traps : enabled authenticate trap : enabled linkchange traps : enabled coldstart traps : enabled warmstart traps :...

  • Page 809

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 804 parameters enable - enable traps for coldstart events. The default state is enabled. Disable - disable traps for coldstart events. Restrictions only administrator and operator-level users can issue this command....

  • Page 810

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 805 70-21 config trap source_ipif description this command is used to force change the ipif information in trap messages. By default, trap messages will carry the information of the ipif they belong to. Format confi...

  • Page 811

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 806 parameters none. Restrictions none. Example to display the trap source ip interface: dgs-3620-28sc:admin#show trap source_ipif command: show trap source_ipif trap source ip interface configuration: ip interface ...

  • Page 812

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 807 success. Dgs-3620-28sc:admin# 70-24 show rmon description this command is used to display rmon related settings. Format show rmon parameters none. Restrictions none. Example to display current rmon settings: dgs...

  • Page 814

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 809 parameters - enter a port or range of ports to be displayed. Restrictions none. Example to display the packets analysis for port 1:7: dgs-3620-28sc:admin#show packet ports 1:7 command: show packet ports 1:7 port...

  • Page 815

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 810 parameters - enter a port or range of ports to be displayed. Restrictions none. Example to display the errors of port 1:3: dgs-3620-28sc:admin#show error ports 1:3 command: show error ports 1:3 port number : 1:3...

  • Page 816

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 811 cpu - specifies to display real-time cpu statistics. Restrictions none. Example to display port utilization: dgs-3620-28sc:admin#show utilization ports command: show utilization ports port tx/sec rx/sec util por...

  • Page 817

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 812 71-4 show utilization dram description this command is used to display real-time dram utilization statistics. Format show utilization dram {unit } parameters unit - specifies which unit on the stacking system. I...

  • Page 818

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 813 example to display flash utilization: dgs-3620-28sc:admin#show utilization flash command: show utilization flash unit 1 flash memory utilization : total flash : 126253 kb used flash : 8271 kb utilization : 6 % c...

  • Page 819

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 814 71-7 clear log description this command is used to clear the switch’s history log. Format clear log parameters none. Restrictions only administrator and operator-level users can issue this command. Example to cl...

  • Page 820

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 815 error - (optional) specify severity level 3. Warning - (optional) specify severity level 4. Notice - (optional) specify severity level 5. Informational - (optional) specify severity level 6. Debug - (optional) s...

  • Page 821

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 816 example to display the method to save log: dgs-3620-28sc:admin#show log_save_timing command: show log_save_timing saving log method: on_demand dgs-3620-28sc:admin# 71-10 show log_software_module description this...

  • Page 822

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 817 parameters time_interval - specifies to save log to flash every xxx minutes. If no log occurs in this period, nothing will be saved. - enter the time between 1 and 65535 minutes. On_demand - specifies to save lo...

  • Page 823

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 818 71-13 disable syslog description this command is used to disable syslog from sending a message. Format disable syslog parameters none. Restrictions only administrator and operator-level users can issue this comm...

  • Page 824

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 819 dgs-3620-28sc:admin#show syslog command: show syslog syslog global state: enabled dgs-3620-28sc:admin# 71-15 config syslog host description this command is used to configure the syslog host configuration. Format...

  • Page 825

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 820 across networks to host. This option enables or disables the host to receive such messages. Enable - enable the host to receive messages. Disable - disable the host to receive messages. Restrictions only adminis...

  • Page 826

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 821 local1 - user-defined facility. Local2 - user-defined facility. Local3 - user-defined facility. Local4 - user-defined facility. Local5 - user-defined facility. Local6 - user-defined facility. Local7 - user-defin...

  • Page 827

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 822 success dgs-3620-28sc:admin# 71-18 show syslog host description this command is used to display syslog host configurations. Format show syslog host {} parameters - (optional) specify the host index. Note: if no ...

  • Page 828

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 823 dgs-3620-28sc:admin#show syslog host command: show syslog host syslog global state: disabled host 1 ip address : 10.1.1.2 severity : warning facility : local10 udp port : 514 status : disabled host 2 ip address ...

  • Page 829

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 824 success. Dgs-3620-28sc:admin# to clear the configured source ip interface for syslog: dgs-3620-28sc:admin#config syslog source_ipif none command: config syslog source_ipif none success. Dgs-3620-28sc:admin# 71-2...

  • Page 830

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 825 format show attack_log {index } parameters index - (optional) specify the list of index of the entries that need to be displayed. - enter the list of index of the entries that need to be displayed. For example, ...

  • Page 831

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 826 example to clear the switch’s attack log: dgs-3620-28sc:admin#clear attack_log command: clear attack_log success. Dgs-3620-28sc:admin# 71-23 show cpu port description this command is use to show statistics for l...

  • Page 832

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 827 dvmrp - specifies to display packet type dvmrp. (ei mode only parameter) reserved_ipv4_ipmc - specifies to display packet type reserved ipv4 ipmc. Reserved_ipv6_ipmc - specifies to display packet type reserved i...

  • Page 833

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 828 rcp 0 0 0 telnet 0 0 0 udp-helper 0 0 0 vrrp 0 0 0 dgs-3620-28sc:admin# to display statistics of all layer 3 multicast routing control packets: dgs-3620-28sc:admin#show cpu port l3 multicast command: show cpu po...

  • Page 834

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 829 parameters none. Restrictions none. Example to clear all counters for all packets: dgs-3620-28sc:admin#clear cpu port command: clear cpu port success. Dgs-3620-28sc:admin#.

  • Page 837

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 832 critical_link_event –specify critical link event. Dying_gasp - an unrecoverable local failure condition has occurred. Critical_event - an unspecified critical event has occurred. Notify_state - specifies the eve...

  • Page 838

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 833 success. Dgs-3620-28sc:admin# to configure the error frame seconds threshold to 2 and period to 10000 ms for port 1: dgs-3620-28sc:admin#config ethernet_oam ports 1 link_monitor error_frame_seconds threshold 2 w...

  • Page 839

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 834 success. Dgs-3620-28sc:admin# 72-2 show ethernet_oam ports description this command is used to display ethernet oam information, including status, configuration, statistics, and event log, on specified ports. Th...

  • Page 840

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 835 the event log displays ethernet oam event log information. The switch can buffer 1000 event logs. The event log is different from sys-log as it provides more detailed information than sys-log. Each oam event wil...

  • Page 844

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 839 point-to-point - specifies to set the network type of designated interfaces to point_to_point. Broadcast - specifies to set the network type of designated interfaces to broadcast. This is the default option. Res...

  • Page 845

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 840 example to create ospf area aggregation settings: dgs-3620-28sc:admin# create ospf aggregation 10.1.1.1 192.168.0.0/16 lsdb_type summary command: create ospf aggresgation 10.1.1.1 192.168.0.0/16 lsdb_type summar...

  • Page 847

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 842 example to display ospf aggregation settings: dgs-3620-28sc:admin#show ospf aggregation command: show ospf aggregation ospf area aggregation settings area id aggregated lsdb advertise network address type ------...

  • Page 848

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 843 65535. Restrictions only administrator, operator and power-user level users can issue this command. Example to create an ospf area: dgs-3620-28sc:admin# create ospf area 10.48.74.122 type stub stub_summary enabl...

  • Page 849

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 844 example to configure an ospf area’s settings: dgs-3620-28sc:admin# config ospf area 10.48.74.122 type stub stub_summary enabled metric 1 command: config ospf area 10.48.74.122 type stub stub_summary enabled metr...

  • Page 850

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 845 parameters - (optional) enter the ospf area id used here. Restrictions none. Example to display ospf area’s configuration: dgs-3620-28sc:admin# show ospf area command: show ospf area ospf area settings area id t...

  • Page 851

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 846 example to create an ospf host route: dgs-3620-28sc:admin# create ospf host_route 10.48.74.122 area 10.1.1.1 metric 2 command: create ospf host_route 10.48.74.122 area 10.1.1.1 metric 2 success. Dgs-3620-28sc:ad...

  • Page 852

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 847 format delete ospf host_route parameters - enter the host’s ip address used here. Restrictions only administrator, operator and power-user level users can issue this command. Example to delete an ospf host route...

  • Page 853

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 848 dgs-3620-28sc:admin# show ospf host_route command: show ospf host_route ospf host route settings host address metric area id --------------- ------ --------------- 10.48.73.21 2 10.1.1.1 10.48.74.122 1 10.1.1.1 ...

  • Page 856

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 851 format delete ospf virtual_link parameters - specifies a 32-bit number in the form of an ip address (xxx.Xxx.Xxx.Xxx) that uniquely identifies the ospf area in the ospf domain. - specifies the ospf router id for...

  • Page 857

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 852 example to display the current ospf virtual interface configuration: dgs-3620-28sc:admin#show ospf virtual_link command: show ospf virtual_link virtual interface configuration transit virtual hello dead authenti...

  • Page 859

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 854 total entries : 1 ospf area aggregation settings area id aggregated lsdb advertise network address type --------------- ------------------ -------- --------- 10.0.0.2 10.0.0.0/8 summary enabled total entries : 1...

  • Page 861

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 856 73-23 show ospf neighbor description this command is used to display the ospf-neighbor information on a per-interface basis. Format show ospf neighbor {} parameters - (optional) specifies the ip address of the n...

  • Page 862

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 857 restrictions none. Example to display ospf virtual-link neighbor information: dgs-3620-28sc:admin# show ospf virtual_neighbor command: show ospf virtual_neighbor transit router id of ip address of virtual neighb...

  • Page 863

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 858 example to set the status of originating the ospf default external route: dgs-3620-28sc:admin#config ospf default-information originate always command: config ospf default-information originate always success. D...

  • Page 865

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 860 example to enable ospfv3: dgs-3620-28sc:admin# enable ospfv3 command: enable ospfv3 success. Dgs-3620-28sc:admin# 74-2 disable ospfv3 description this command is used to disable ospfv3 on the switch. Format disa...

  • Page 866

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 861 parameters ipif - (optional) specifies the ospfv3 ip interface name used. - enter the ospfv3 ip interface name used here. This name can be up to 12 characters long. All - (optional) specifies that all the ospfv3...

  • Page 867

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 862 total entries: 0 dgs-3620-28sc:admin# show ospfv3 all command: show ospfv3 all interface name: system link local address: fe80::201:2ff:fe03:400 (link up) network medium type: broadcast metric: 10 area id: 0.0.0...

  • Page 868

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 863 restrictions only administrator, operator and power-user level users can issue this command. (ei mode only command) example to set ospfv3 router id: dgs-3620-28sc:admin# config ospfv3 router_id 1.1.1.1 command: ...

  • Page 869

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 864 dgs-3620-28sc:admin# create ospfv3 area 1.1.1.1 type normal command: create ospfv3 area 1.1.1.1 type normal success. Dgs-3620-28sc:admin# create ospfv3 area 2.2.2.2 type stub stub_summary enable command: create ...

  • Page 871

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 866 example to display ospfv3 areas: dgs-3620-28sc:admin# show ospfv3 area command: show ospfv3 area ospfv3 area settings area id type stub import summary lsa stub default cost --------------- ------ ---------------...

  • Page 872

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 867 restrictions only administrator, operator and power-user level users can issue this command. (ei mode only command) example to create an ospfv3 area aggregation: dgs-3620-28sc:admin# create ospfv3 aggregation 2....

  • Page 874

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 869 example to display ospfv3 area aggregations: dgs-3620-28sc:admin# show ospfv3 aggregation command: show ospfv3 aggregation ospfv3 area aggregation settings area id aggregated lsdb advertise network address type ...

  • Page 875

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 870 intra_area_prefix - specifies that the intra-area-prefix lsa will be displayed. Restrictions none. (ei mode only command) example to display ospfv3 link-state database: dgs-3620-28sc:admin# show ospfv3 lsdb comm...

  • Page 876

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 871 parameters - (optional) specifies the id of the neighbor. Ipif - (optional) specifies the ip interface where the neighbor is built. - enter the ip interface name used here. This name can be up to 12 characters l...

  • Page 877

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 872 restrictions none. (ei mode only command) example to display ospfv3 virtual neighbor: dgs-3620-28sc:admin# show ospfv3 virtual_neighbor command: show ospfv3 virtual_neighbor transit router id of virtual neighbor...

  • Page 878

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 873 hello_interval - (optional) specifies to allow the specification of the interval between the transmission of ospfv3 hello packets, in seconds. The hello interval and dead interval should be the same for all rout...

  • Page 879

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 874 parameters - specifies a 32-bit number in the form of an ipv4 address that uniquely identifies the ospfv3 area in the ospfv3 domain. This area is the transit area where the virtual link is built. - specifies a 3...

  • Page 880

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 875 the ospfv3 virtual neighbor in the ospfv3 domain. Hello_interval - (optional) specifies to allow the specification of the interval between the transmission of ospfv3 hello packets. The hello interval and dead in...

  • Page 881

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 876 example to delete an ospfv3 virtual link: dgs-3620-28sc:admin# delete ospfv3 virtual_link 1.1.1.1 60.60.60.60 command: delete ospfv3 virtual_link 1.1.1.1 60.60.60.60 success. Dgs-3620-28sc:admin# 74-20 show ospf...

  • Page 882

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 877 command: show ospfv3 virtual_link 1.1.1.1 60.60.60.60 transit area id: 1.1.1.1 virtual neighbor router id: 60.60.60.60 hello interval: 10 dead interval: 60 transmit delay: 1 retransmit time: 5 instance id: 0 vir...

  • Page 884

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 879 - enter the value between 0 and 255000. Broadcast_threshold - specifies the upper threshold, at which point the specified storm control is triggered. The value is the number of broadcast packets per second recei...

  • Page 886

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 881 example to configure the traffic log state on the switch: dgs-3620-28sc:admin# config traffic control log state enable command: config traffic control log state enable success. Dgs-3620-28sc:admin# 75-4 config t...

  • Page 888

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 883 dgs-3620-28sc:admin#.

  • Page 889: Chapter 76

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 884 chapter 76 password recovery commands enable password_recovery disable password_recovery show password_recovery 76-1 enable password_recovery description this command is used to enable the password recovery mode...

  • Page 890

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 885 format disable password_recovery parameters none. Restrictions only administrator-level users can issue this command. Example to disable the password recovery mode: dgs-3620-28sc:admin# disable password_recovery...

  • Page 891

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 886 example to display the password recovery state: dgs-3620-28sc:admin# show password_recovery command: show password_recovery running configuration : disabled nv-ram configuration : enabled dgs-3620-28sc:admin#.

  • Page 893

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 888 - enter the ip interface name used here. This name can be up to 12 characters long. All - specifies that all the ip interfaces will be used. Hello - (optional) specifies the time between issuing hello packets to...

  • Page 894

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 889 format enable pim parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to enable pim: dgs-3620-28sc:admin# enable pim command: enable pim success....

  • Page 896

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 891 parameters ipif - (optional) specifies the name of the ip interface used to display the pim configuration. - enter the ip interface name used here. This name can be up to 12 characters long. If no parameter is s...

  • Page 897

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 892 255. Hash_masklen - enter a hash mask length, which will be used with the ip address of the candidate rp and the multicast group address, to calculate the hash algorithm used by the router to determine which crp...

  • Page 898

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 893 c-bsr hash mask len : 30 c-bsr bootstrap period : 60 interface ip address priority ------------ ------------------ ------------- system 11.52.33.3/8 -1 (disabled) total entries: 1 dgs-3620-28sc:admin# 77-8 confi...

  • Page 899

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 894 success. Dgs-3620-28sc:admin# 77-9 create pim crp group description this command is used to add a multicast group range into a c-rp serve list for pim-sm. Format create pim crp group rp parameters group - specif...

  • Page 900

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 895 restrictions only administrator, operator and power-user level users can issue this command. Example to delete a multicast group range from the c-rp server list: dgs-3620-28sc:admin# delete pim crp group 224.1.2...

  • Page 901

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 896 dgs-3620-28sc:admin# 77-12 config pim last_hop_spt_switchover description this command is used by the last hop router to decide whether to receive the multicast data from the shared tree or switch over to the sh...

  • Page 902

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 897 restrictions none. Example to list all the entries of multicast routing: dgs-3620-28sc:admin# show pim ipmroute command: show pim ipmroute pim ip multicast route table ua = upstream asserttimer am = assert metri...

  • Page 903

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 898 example to create a static rp: dgs-3620-28sc:admin# create pim static_rp group 239.1.1.0/24 rp 10.52.33.18 command: create pim static_rp group 239.1.1.0/24 rp 10.52.33.18 success. Dgs-3620-28sc:admin# 77-15 dele...

  • Page 904

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 899 parameters none. Restrictions none. Example to list all the static rp settings: dgs-3620-28sc:admin# show pim static_rp command: show pim static_rp pim static rp table group rp address ------------------ -------...

  • Page 905

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 900 bootstrap router: 10.54.71.9 group address rp address holdtime expired time type --------------- ---------- -------- ------------ ---- 224.0.0.0/4 10.20.6.36 210 196 dynamic 224.0.0.0/4 10.54.71.9 0 0 static tot...

  • Page 906

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 901 77-19 delete pim register_checksum_include_data rp_address description this command is used to delete the register checksum including the data for the specific rp address. Format delete pim register_checksum_inc...

  • Page 907

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 902 example to list all the rps of the registered checksum, including the data: dgs-3620-28sc:admin# show pim register_checksum_include_data_rp_list command: show pim register_checksum_include_data_rp_list pim regis...

  • Page 908

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 903 77-22 show pim-ssm description this command is used to list all pim-ssm protocol related information. Format show pim-ssm parameters none. Restrictions none. Example to display pim-ssm state and group range: dgs...

  • Page 909

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 904 dgs-3620-28sc:admin#show pim passive command: show pim passive interface passive ------------ -------- system disabled total entries: 1 dgs-3620-28sc:admin#.

  • Page 911

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 906 routers. A value of zero represents an ‘infinite’ interval, and indicates that periodic pim6 hello message should not be sent on this interface. - enter the hello packet interval value here. This value must be b...

  • Page 912

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 907 success. Dgs-3620-28sc:admin# 78-2 show pim6 description this command is used to display the pim6 configurations. Format show pim6 {ipif } parameters ipif - (optional) specifies the ip interface to be displayed....

  • Page 913

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 908 to show the detailed info of the pim6 protocol concerned parameters on the interface “system”: dgs-3620-28sc:admin# show pim6 ipif system command: show pim6 ipif system interface name : system interface link-loc...

  • Page 914

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 909 - enter the length of the mask value here. This value must be between 0 and 128. The default value is 126. Restrictions only administrator, operator and power-user level users can issue this command. (ei mode on...

  • Page 916

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 911 parameters group - specifies the ipv6 group address range served by the rp. - enter the ipv6 network address used here. Rp - specifies the interface that will act as the c-rp. - enter the ip interface name used ...

  • Page 917

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 912 dgs-3620-28sc:admin# 78-8 enable pim6 description this command is used to enable the pim global state for ipv6 network. Format enable pim6 parameters none. Restrictions only administrator, operator and power-use...

  • Page 918

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 913 example to disable pim-sm for ipv6 network: dgs-3620-28sc:admin# disable pim6 command: disable pim6 success. Dgs-3620-28sc:admin# 78-10 config pim6 last_hop_spt_switchover description this command is used on the...

  • Page 919

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 914 parameters ipif - (optional) specifies the ip interface used. - enter the ip interface name used here. This name can be up to 12 characters long. If no parameter is specified, the system will display all neighbo...

  • Page 920

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 915 format show pim6 mroute {group {source }} parameters group - (optional) specifies the ipv6 multicast group address. - enter the ipv6 multicast group address used here. Source - (optional) specifies the ipv6 sour...

  • Page 921

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 916 dgs-3620-28sc:admin# show pim6 mroute group ff13::100 command: show pim6 mroute group ff13::100 (*, g) entry for group ff13::100 --------------------------------------------- rp address : 3ffe:10:10::153 upstrea...

  • Page 922

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 917 upstream : n1 upstream state : rpt not joined rpf neighbor : fe80::68fe override timer : 3 sec pruned : n10 outgoing : - total entries: 2 dgs-3620-28sc:admin# 78-13 create pim6 static_rp group description this c...

  • Page 923

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 918 format delete pim6 static_rp group parameters group - specifies the multicast group network address which will be removed from the static rp. - enter the ipv6 network address used here. Restrictions only adminis...

  • Page 924

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 919 success. Dgs-3620-28sc:admin# 78-16 show pim6 crp description this command is used to list all candidate rendezvous point (rp) related information. Format show pim6 crp parameters none. Restrictions none. (ei mo...

  • Page 925

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 920 restrictions none. (ei mode only command) example to show the static rp: dgs-3620-28sc:admin# show pim6 static_rp command: show pim6 static_rp pim6 static rp table --------------------------------------------- g...

  • Page 926

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 921 pim6 rp-set table ----------------------------------------- group : ff3d::/64 rp address : 2008::10f2 hold time : 210 sec expired time : 196 sec type : dynamic group : ff3d::/64 rp address : 3008::2def override ...

  • Page 927

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 922 success. Dgs-3620-28sc:admin# 78-20 config pim6 register_probe_time description this command is used to configure the pim6-sm register probe time. Format config pim6 register_probe_time parameters register_probe...

  • Page 928

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 923 register-encapsulated data to the rp after receiving a register-stop message. - enter the register suppression time value here. This value must be between 3 and 65535 seconds. The default value is 60 seconds. Re...

  • Page 929

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 924 dgs-3620-28sc:admin# 78-23 show pim6 mroute s_g description this command is used to display the multicast routing information for (s, g) or (s, g, rpt) entries generated by pim6. Format show pim6 mroute s_g {rpt...

  • Page 930

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 925 total entries: 4 dgs-3620-28sc:admin# check the detailed information for a specific multicasting route entry by specifying the options in the command. To show the detailed information of the multicast route entr...

  • Page 931

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 926 dgs-3620-28sc:admin# to show the whole ipv6 multicast routing table of (s, g, rpt) generated on the switch: dgs-3620-28sc:admin# show pim6 mroute s_g rpt command: show pim6 mroute s_g rpt (s, g, rpt) entry table...

  • Page 932

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 927 group address : ff13::100 source address : 2001::1111 interface name : n20 uptime : 150 sec have local membership : false join prune state : prune prune pending timer : 0 sec prune expiry timer : 15 sec dgs-3620...

  • Page 933

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 928 group : ff13::102 upstream : n2 rp address : 3ffe:10:10::153 total entries: 3 dgs-3620-28sc:admin# check the detailed information for a specific multicasting routing entry by specifying the options in the comman...

  • Page 935

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 930 parameters - the policy route name. The maximum length is 32 characters. Restrictions only administrator, operator and power-user level users can issue this command. Example to delete a policy route named “duhon...

  • Page 936

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 931 route_preference - (optional) specifies the priority of this policy route. By default, the policy route has higher priority than the routing table, including local, default, static, and dynamic routes. The one t...

  • Page 937

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 932 dgs-3620-28sc:admin#show policy_route command: show policy_route policy routing table --------------------- name pro- access next hop state route file id pre- id ference -------------------------------- ----- --...

  • Page 939

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 934 vlan of the entry is removed or the port are removed from the vlan, or port security is disabled on the port where the address resides. Deleteontimeout - the locked addresses can be aged out after aging timer ex...

  • Page 941

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 936 restrictions only administrator, operator and power-user level users can issue this command. Example to configure the maximum number of entries that can be learned at 64: dgs-3620-28sc:admin#config port_security...

  • Page 943

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 938 restrictions none. Example to display a port security entry: dgs-3620-28sc:admin#show port_security_entry command: show port_security_entry mac address vid port lock mode ----------------- --- ---- ---------- 00...

  • Page 944

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 939 port security log state : disabled system maximum address : no limit vlan configuration (only vlans with limitation are displayed) vid vlan name max. Learning addr. ---- -------------------------------- --------...

  • Page 945

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 940 dgs-3620-28sc:admin#config port_security log state enable command: config port_security log state enable success. Dgs-3620-28sc:admin# 80-9 config port_security trap state description this command is used to ena...

  • Page 947

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 942 power_limit - (optional) specifies the per-port power limit. If a port exceeds its power limit, it will be shut down. Based on the industry standard, 802.3af, there are 4 kinds of pd classes, class 0, class 1, c...

  • Page 948

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 943 power_limit - (optional) specifies the power budget of the poe system. - enter the power budger limit value here. This value must be between 37 and 760. Power_disconnect_method - (optional) specifies the disconn...

  • Page 949

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 944 - enter the list of ports, used for the display, here. If no parameter is specified, the system will display the status for all the ports. Restrictions none. Example to display poe port configurations on port 1 ...

  • Page 950

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 945 parameters units - (optional) specifies the unit list, that will be displayed, here. - enter the unit list, used for this display, here. If no parameter is specified, the system will display the status of all th...

  • Page 952

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 947 link_detection - (optional) specify the link detection state. Led - (optional) specify to configure the power saving state of port led. Port - (optional) specify to configure the power saving state of port. Hibe...

  • Page 953

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 948 dgs-3620-28sc:admin#config power_saving hibernation add time_range range_1 command: config power_saving hibernation add time_range range_1 success. Dgs-3620-28sc:admin# 82-3 config power_saving led description t...

  • Page 955

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 950 led - (optional) display the port led configuration of power saving. Port - (optional) display the port configuration of power saving. Hibernation - (optional) display the system hibernation configuration of pow...

  • Page 956

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 951 restrictions only administrator and operator-level users can issue this command. Example to disable the led admin state: dgs-3620-28sc:admin#config led state disable command: config led state disable success. Dg...

  • Page 958

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 953 restrictions only administrator, operator and power-user level users can issue this command. Example to enable the ptp function globally: dgs-3620-28sc:admin# enable ptp command: enable ptp success. Dgs-3620-28s...

  • Page 959

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 954 a boundry clock: • has multiple precision time protocol (ptp) ports in a domain and maintains the timescale used in the domain. • can serve as the time source and can synchronize with another clock. • device typ...

  • Page 960

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 955 parameters ethernet - specifies the transport protocol of ptp as ieee802.3 ethernet. Udp - specifies the transport protocol of ptp as udp over ipv4. Restrictions only administrator, operator and power-user level...

  • Page 961

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 956 example to configure the domain number of the ptp clock as 1 and assign a domain name of internal_domain on the local unit, when the stacking mode is disabled: dgs-3620-28sc:admin# config ptp clock domain_number...

  • Page 962

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 957 dgs-3620-28sc:admin# config ptp boundary priority1 127 command: config ptp boundary priority1 127 success. Dgs-3620-28sc:admin# 83-7 config ptp ports description this command is used to configure the per port st...

  • Page 964

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 959 dgs-3620-28sc:admin# config ptp boundary ports 1:1-1:4 announce interval 3 command: config ptp boundary ports 1:1-1:4 announce interval 3 the announce interval is automatically adjusted to 4. Success. Dgs-3620-2...

  • Page 965

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 960 dgs-3620-28sc:admin# config ptp boundary ports all delay_mechanism p2p command: config ptp boundary ports all delay_mechanism p2p success. Dgs-3620-28sc:admin# 83-9 config ptp p2p_transparent ports description t...

  • Page 966

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 961 parameters none. Restrictions none. Example to show the global ptp configuration: dgs-3620-28sc:admin# show ptp command: show ptp ptp state setting : enabled ptp mode setting : boundary clock ptp transport proto...

  • Page 967

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 962 dgs-3620-28sc:admin# show ptp clock command: show ptp clock ptp state : enabled ptp clock mode : boundary clock ptp transport protocol : udp ptp clock domain number : 1 ptp clock domain name : internal_domain pt...

  • Page 968

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 963 ptp steps removed : 2 ptp last offset : +110 ns ptp mean path delay : 120 second ptp enabled ports : 1:1-1:4 box id: 2 ptp state : enabled ptp clock mode : boundary clock ptp transport protocol : udp ptp clock d...

  • Page 969

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 964 dgs-3620-28sc:admin# show ptp clock parent command: show ptp clock parent ptp parent port identity : acde48fffe6789ab ptp parent port number : 3 ptp grandmaster identity : acde48fffe9789ad ptp grandmaster clock ...

  • Page 970

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 965 dgs-3620-28sc:admin# show ptp clock parent command: show ptp clock parent box id: 1 ptp parent port identity : acde4823456789ab ptp parent port number : 3 ptp grandmaster identity : acde4823659789ad ptp grandmas...

  • Page 971

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 966 dgs-3620-28sc:admin# show ptp ports 1:1-1:4 command: show ptp ports 1:1-1:4 the active attributes: dm : delay mechanism ai : announce interval art : announce receipt timeout si : synchronization interval drim: d...

  • Page 972

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 967 parameters ports – (optional) specifies the list of port used for this display. - enter the list of port used for this display here. All - specifies that all the ports will be used for this display. Restrictions...

  • Page 974

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 969 example to show the current records of the foreign master data set for special ports 1:1-1:3 of the boundary clock: dgs-3620-28sc:admin#show ptp foreign_master_records ports all command: show ptp foreign_master_...

  • Page 976

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 971 84-2 config dot1v_protocol_group description this command is used to add a protocol to a protocol group. The selection of a protocol can be a pre-defined protocol type or a user defined protocol. Format config d...

  • Page 977

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 972 example to add a protocol ipv6 to protocol group 4: dgs-3620-28sc:admin# config dot1v_protocol_group group_id 4 add protocol ethernet_2 86dd command: config dot1v_protocol_group group_id 4 add protocol ethernet_...

  • Page 980

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 975 parameters ports - (optional) specify a range of ports to be displayed. - enter a range of ports to be displayed. Note: if no parameter is specified, information for all ports will be displayed. Restrictions non...

  • Page 982

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 977 restrictions only administrator, operator and power-user level users can issue this command. Example to configure port bandwidth: dgs-3620-28sc:admin#config bandwidth_control 1-10 tx_rate 1024 command: config ba...

  • Page 983

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 978 1 no limit no limit no limit no limit 2 no limit no limit no limit no limit dgs-3620-28sc:admin# 85-3 config per_queue bandwidth_control description this command is used to set the bandwidth control for each spe...

  • Page 984

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 979 success. Dgs-3620-28sc:admin# 85-4 show per_queue bandwidth_control description this command is used to display the bandwidth control setting of per egress queue for each port. Format show per_queue bandwidth_co...

  • Page 985

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 980 parameters ports - (optional) specifies the range of ports to be configured. - enter the list of ports here. All - specifies that all the ports will be used. - specifies the 8 hardware priority queues that the c...

  • Page 986

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 981 wrr - specifies that each queue will operate based on their weight settings. Restrictions only administrator, operator and power-user level users can issue this command. Example to configure the traffic scheduli...

  • Page 987

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 982 class id weight -------- ------ class-0 1 class-1 2 class-2 3 class-3 4 class-4 5 class-5 6 class-6 7 class-7 8 qos output scheduling on port: 2 class id weight -------- ------ class-0 1 class-1 2 class-2 3 clas...

  • Page 988

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 983 parameters - (optional) specifies a range of ports to be displayed. Restrictions none. Example to display the scheduling mechanism for all ports: dgs-3620-28sc:admin#show scheduling_mechanism command: show sched...

  • Page 989

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 984 85-9 config 802.1p user_priority description this command is used to configure the way by which the switch will map an incoming packet, based on its 802.1p user priority, to one of the eight available hardware p...

  • Page 990

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 985 85-10 show 802.1p user_priority description this command is used to display 802.1p user priority. Format show 802.1p user_priority {} parameters - (optional) specifies the range of ports to be configured. Restri...

  • Page 992

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 987 parameters - (optional) specify a range of ports to be displayed. Note: if no parameter is specified, the system will display all ports with 802.1p default priority. Restrictions none. Example to display 802.1p ...

  • Page 993

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 988 success. Dgs-3620-28sc:admin# 85-14 disable hol_prevention description this command is used to disable head of line prevention on the switch. Format disable hol_prevention parameters none. Restrictions only admi...

  • Page 994

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 989 example to display hol prevention state on the switch: dgs-3620-28sc:admin#show hol_prevention command: show hol_prevention device hol prevention state: enabled dgs-3620-28sc:admin# 85-16 config dscp trust descr...

  • Page 995

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 990 parameters - a range of ports to display. If not specifying any ports, the dscp trust status for all ports on the switch will be displayed. Restrictions only administrator, operator level users can issue this co...

  • Page 996

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 991 restrictions only administrator, operator level users can issue this command. Example in the case of a product supporting per-port dscp mapping configuration, to configure the mapping of dscp priority 1 to prior...

  • Page 997

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 992 example in the case of a product supporting per port configuration.,to show the dscp map configuration on port 1:1. Dgs-3620-28sc:admin#show dscp map 1 dscp_priority command: show dscp map 1 dscp_priority dscp t...

  • Page 999

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 994 example to enable q-in-q: dgs-3620-28sc:admin#enable qinq command: enable qinq success. Dgs-3620-28sc:admin# 86-2 disable qinq description this command is used to disable q-in-q. When q-in-q is disabled, all dyn...

  • Page 1000

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 995 parameters none. Restrictions none. Example to display q-in-q: dgs-3620-28sc:admin#show qinq command: show qinq qinq status : enabled dgs-3620-28sc:admin# 86-4 config qinq ports description this command is used ...

  • Page 1001

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 996 add - specifies to add a vlan translation profile. Delete - specifies to delete a vlan translation profile. Vlan_translation_profile - specifies the vlan translation profile id. - enter the vlan translation prof...

  • Page 1002

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 997 86-6 show qinq inner_tpid description this command is used to display the inner tpid of the system. Format show qinq inner_tpid parameters none. Restrictions none. Example to display the inner tpid of the system...

  • Page 1003

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 998 example to display the q-in-q mode for ports 1 to 2: dgs-3620-28sc:admin#show qinq ports 1-2 command: show qinq ports 1-2 port id: 1 --------------------------------------------------------- role: nni miss drop:...

  • Page 1004

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 999 priority in the c-tag. - enter a 802.1p priority of the s-tag between 0 and 7. Restrictions only administrator, operator and power-user level users can issue this command. Example to replace the c-tag by the s-t...

  • Page 1005

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1000 example to delete a vlan translation rule on ports 1 to 4: dgs-3620-28sc:admin#delete vlan_translation ports 1-4 command: delete vlan_translation ports 1-4 success. Dgs-3620-28sc:admin# 86-10 show vlan_translat...

  • Page 1006

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1001 86-11 create vlan_translation_profile description this command is used to create a flow-based vlan translation profile. Multiple flow-based vlan translation rules can be specified for a profile. Format create v...

  • Page 1007

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1002 parameters - specifies the profile id number to be configured. Add - specifies to add a tag for the assigned s-vlan before the outer-vlan tag. If there is an s- tag in the packet, this rule will not take effect...

  • Page 1008

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1003 sa_mask - specifies the source mac address mask. - enter the source mac address mask here. Destination_mac - specifies the destination mac address or mac address range for the match. - enter the destination mac...

  • Page 1009

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1004 success. Dgs-3620-28sc:admin#config qinq ports 1:3 add vlan_translation_profile 3 command: config qinq ports 1:3 add vlan_translation_profile 3 success. Dgs-3620-28sc:admin#config vlan_translation_profile 3 add...

  • Page 1010

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1005 priority: match: outer-vid : 10 total rule : 1 dgs-3620-28sc:admin# 86-14 delete vlan_translation_profile description this command is used to delete a qinq translation profile or delete a qinq rule in a profile...

  • Page 1011

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1006.

  • Page 1014

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1009 dgs-3620-28sc:admin# config rip ipif system rx_mode v1_only command: config rip ipif system rx_mode v1_only success. Dgs-3620-28sc:admin# 87-3 config rip timers description this command is used to configure rip...

  • Page 1015

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1010 format disable rip parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable rip: dgs-3620-28sc:admin# disable rip command: disable rip suc...

  • Page 1016

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1011 dgs-3620-28sc:admin#show rip command: show rip rip global state : enabled update time : 120 seconds timeout time : 300 seconds garbage collection time : 150 seconds rip interface settings interface ip address t...

  • Page 1018

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1013 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. (ei mode only command) example to disable ripng globally: dgs-3620-28sc:admin# disable ripng command...

  • Page 1019

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1014 dgs-3620-28sc:admin#show ripng command: show ripng global state: disabled method: split horizon update time: 30 seconds expire time: 180 seconds garbage collection time: 120 seconds interface state metric -----...

  • Page 1020

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1015 dgs-3620-28sc:admin# config ripng method poison_reverse command: config ripng method poison_reverse success. Dgs-3620-28sc:admin# 88-5 config ripng ipif description this command is used to specify the ripng sta...

  • Page 1022

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1017 parameters none. Restrictions only administrator and operator-level users can issue this command. Example to disable the rspan globally: dgs-3620-28sc:admin#disable rspan command: disable rspan success. Dgs-362...

  • Page 1023

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1018 to create an rspan vlan entry by vlan id “3”: dgs-3620-28sc:admin#create rspan vlan vlan_id 3 command: create rspan vlan vlan_id 3 success. Dgs-3620-28sc:admin# 89-4 delete rspan vlan description this command i...

  • Page 1024

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1019 89-5 config rspan vlan description this command is used by the source switch to configure the source setting for the rspan vlan. The redirect command is used by the intermediate or last switch to configure the ...

  • Page 1025

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1020 dgs-3620-28sc:admin#config rspan vlan vlan_name vlan2 source add ports 2-5 rx command: config rspan vlan vlan_name vlan2 source add ports 2-5 rx success. Dgs-3620-28sc:admin# to configure an rspan source entry ...

  • Page 1026

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1021 rspan : enabled rspan vlan id : 63 ------------------- mirror group id : 1 target port : 1:1 source ports rx : 1:2-1:5 tx : 1:2-1:5 redirect ports : 1:9-1:12 total rspan vlan : 1 dgs-3620-28sc:admin# to display...

  • Page 1028

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1023 example to configure the safeguard engine: dgs-3620-28sc:admin#config safeguard_engine state enable utilization rising 50 falling 30 trap_log enable command: config safeguard_engine state enable utilization ris...

  • Page 1029: Chapter 91

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1024 chapter 91 secure file transfer protocol (sftp) commands enable sftp server disable sftp server config sftp server {timeout }(1) show sftp server 91-1 enable sftp server description this command is used to enab...

  • Page 1030

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1025 91-2 disable sftp server description this command is used to disable the sftp server function globally. All active sftp sessions will be disturbed after executing this command. Sftp server runs as a subsystem o...

  • Page 1031

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1026 example to configure idle timer to 600 seconds. Dgs-3620-28sc:admin#config sftp server timeout 600 command: config sftp server timeout 600 success. Dgs-3620-28sc:admin# 91-4 show sftp server description this co...

  • Page 1033

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1028 success. Dgs-3620-28sc:admin# 92-2 disable sflow description this command is used to disable the sflow function. Format disable sflow parameters none. Restrictions only administrator and operator-level users ca...

  • Page 1034

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1029 example to display the sflow information: dgs-3620-28sc:admin#show sflow command: show sflow sflow version : v5 sflow address : 10.90.90.90 sflow addressv6: fe80::201:2ff:fe03:400 sflow state : enabled dgs-3620...

  • Page 1035

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1030 200 maxheadersize 120 command: create sflow flow_sampler ports 1 analyzer_server_id 1 rate 200 maxheadersize 120 success. Dgs-3620-28sc:admin# 92-5 config sflow flow_sampler ports description this command is us...

  • Page 1037

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1032 - enter the time out value, in seconds, between 1 and 2000000. Infinite - specifies to never time out. Collectoraddress - (optional) specify the ip address of the analyzer server. - enter the ip address of the ...

  • Page 1038

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1033 success. Dgs-3620-28sc:admin# 92-9 config sflow analyzer_server description this command is used to configure the sflow analyzer server information. More than one collector with the same ip address can be speci...

  • Page 1039

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1034 92-10 show sflow analyzer_server description this command is used to display sflow analyzer server information. Format show sflow analyzer_server parameters none. Restrictions only administrator, operator and p...

  • Page 1040

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1035 parameters - enter the ports to be configured. All - specifies to configure all ports. Analyzer_server_id - specifies the id of an analyzer server where the packet will be forwarded. - enter the id of an analyz...

  • Page 1041

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1036 dgs-3620-28sc:admin#config sflow counter_poller ports 1 interval 50 command: config sflow counter_poller ports 1 interval 50 success. Dgs-3620-28sc:admin# 92-13 delete sflow counter_poller ports description thi...

  • Page 1042

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1037 restrictions only administrator, operator and power-user level users can issue this command. Example to display sflow counter poller information for the ports that have been created: dgs-3620-28sc:admin#show sf...

  • Page 1044

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1039 93-2 disable sim description this command is used to configure the single ip management on the switch as disabled. Format disable sim parameters none. Restrictions only administrator, operator and power-user le...

  • Page 1045

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1040 restrictions none. Example to show the self information in detail: dgs-3620-28sc:admin#show sim command: show sim sim version : ver-1.61 firmware version : 2.50.014 device name : mac address : 00-01-02-03-04-00...

  • Page 1046

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1041 to show other groups information in summary: dgs-3620-28sc:admin#show sim group command: show sim group sim group name : default id mac address platform / hold firmware device name capability time version --- -...

  • Page 1048

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1043 example to add a member: dgs-3620-28sc:admin#config sim_group add 2 command: config sim_group add 2 please wait for ack !!! Sim config success !!! Success. Dgs-3620-28sc:admin# to delete a member: dgs-3620-28sc...

  • Page 1049

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1044 example to transfer to commander: dgs-3620-28sc:admin#config sim commander command: config sim commander success. Dgs-3620-28sc:admin# to transfer to candidate: dgs-3620-28sc:admin#config sim candidate command:...

  • Page 1051

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1046 this device is updating configuration. Please wait several minutes... Download status : id mac address result --- ----------------- ---------------- 1 00-01-02-03-04-00 success 2 00-07-06-05-04-03 transfer fail...

  • Page 1052

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1047 1 00-01-02-03-04-00 success dgs-3620-28sc:admin#.

  • Page 1054

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1049 parameters - enter the name of the user on the host that connects to the agent. The range is 1 to 32 characters. - enter the name of the group to which the user is associated. The range is 1 to 32 characters. E...

  • Page 1055

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1050 format delete snmp user parameters - enter the name of the user on the host to be deleted. The range is 1 to 32 characters. Restrictions only administrator-level users can issue this command. Example to delete ...

  • Page 1056

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1051 username group name verauthpriv --------------------------- --------------------------- ------------ initial initial v3 nonenone total entries : 1 dgs-3620-28sc:admin# 94-4 show snmp groups description this com...

  • Page 1057

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1052 readview name : communityview writeview name : communityview notify view name : communityview security model : snmpv2 security level : noauthnopriv total entries: 3 dgs-3620-28sc:admin# 94-5 create snmp view de...

  • Page 1058

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1053 parameters - enter the view name of the user who will be deleted. All - specifies to view all records. - enter the object-identified tree (the mib tree). Restrictions only administrator-level users can issue th...

  • Page 1059

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1054 restricted 1.3.6.1.6.3.11.2.1 included restricted 1.3.6.1.6.3.15.1.1 included communityview 1 included communityview 1.3.6.1.6.3 excluded communityview 1.3.6.1.6.3.1 included total entries: 8 dgs-3620-28sc:admi...

  • Page 1060

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1055 94-9 delete snmp community description this command is used to remove a specific community string. Format delete snmp community parameters - enter the community string that will be deleted. Restrictions only ad...

  • Page 1061

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1056 example to display the current community string configurations: dgs-3620-28sc:admin#show snmp community command: show snmp community snmp community table community name view name access right ------------------...

  • Page 1062

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1057 success. Dgs-3620-28sc:admin# 94-12 config snmp engineid description this command is used to configure an identifier for the snmp engine on the switch. Associated with each snmp entity is a unique engine id. Fo...

  • Page 1063

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1058 example to display the identification of an snmp engine: dgs-3620-28sc:admin#show snmp engineid command: show snmp engineid snmp engine id : 1023457890 dgs-3620-28sc:admin# 94-14 create snmp group description t...

  • Page 1064

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1059 dgs-3620-28sc:admin# 94-15 delete snmp group description this command is used to remove an snmp group. Format delete snmp group parameters - enter the name of the group that will be deleted. Restrictions only a...

  • Page 1065

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1060 auth_priv - specifies to support packet authentication and encrypting. - enter the authentication string. If v1 or v2 is specified, the auth_string presents the community string, and it must be one of the entri...

  • Page 1066

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1061 dgs-3620-28sc:admin# 94-18 show snmp host description this command is used to display the recipient for which the traps are targeted. Format show snmp host {} parameters - (optional) specify the ip address of t...

  • Page 1067

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1062 parameters - (optional) specify the v6host ip address. Note: if no parameter is specified, all snmp ipv6 hosts will be displayed. Restrictions none. Example to display the recipient for which the traps are targ...

  • Page 1068

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1063 command: enable community_encryption success. Dgs-3620-28sc:admin# when creating an snmp community string after the encryption state has been enabled, the community string will be displayed as an encrypted stri...

  • Page 1069

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1064 dgs-3620-28sc:admin# 94-22 show community_encryption description this command is used to display the encryption state on the snmp community string. Format show community_encryption parameters none. Restrictions...

  • Page 1070

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1065 restrictions only administrator level users can issue this command. Example to enable the per port snmp trap state: dgs-3620-28sc:admin#config snmp trap_port all state enable command: config snmp trap_port all ...

  • Page 1073

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1068 dgs-3620-28sc:admin#show stp command: show stp stp bridge global settings --------------------------- stp status : disabled stp version : rstp max age : 20 hello time : 2 forward delay : 15 max hops : 20 tx hol...

  • Page 1074

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1069 dgs-3620-28sc:admin#show stp instance command: show stp instance stp instance settings --------------------------- instance type : cist instance status : enabled instance priority : 32768(bridge priority : 3276...

  • Page 1075

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1070 port index : 1 , hello time : 2 /2 , port stp : enabled external pathcost : auto/200000 , edge port : false/no , p2p : false/no port restrictedrole : false, port restrictedtcn : false port forward bpdu : enable...

  • Page 1076

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1071 95-5 create stp instance_id description this command is used to create a new mst instance independent from the default instance: cist (instance 0). After creating the mst instance, a user needs to configure the...

  • Page 1077

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1072 example to delete an mstp instance: dgs-3620-28sc:admin#delete stp instance_id 2 command: delete stp instance_id 2 success. Dgs-3620-28sc:admin# 95-7 config stp instance_id description there are two different a...

  • Page 1078

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1073 success. Dgs-3620-28sc:admin# 95-8 config stp mst_config_id description this command is used to configure a configuration name or revision level in the mst configuration identification. The default configuratio...

  • Page 1079

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1074 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to enable stp: dgs-3620-28sc:admin#enable stp command: enable stp success. Dgs-3620-28sc:adm...

  • Page 1080

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1075 95-11 config stp version description this command is used to change stp version. If the version is configured as stp or rstp, all currently running mstis should be disabled. If the version is configured as mstp...

  • Page 1081

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1076 parameters - enter the bridge priority value, which must be divisible by 4096. The default value is 32768. Instance_id - specifies the identifier value, which is used to distinguish different stp instances. - e...

  • Page 1082

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1077 disable - specifies to disable fbpdu. Nni_bpdu_addr - specifies to determine the bpdu protocol address for stp in service provide site. It can use 802.1d stp address, 802.1ad service provider stp address. Dot1d...

  • Page 1083

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1078 p2p - decide if this port is in full-duplex or half-duplex mode. True - specifies full-duplex mode. False - specifies half-duplex mode. Auto - the switch will automatically determine the p2p mode. State - decid...

  • Page 1084

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1079 priority - specifies the port priority. - enter a value between 0 and 240. Restrictions only administrator, operator and power-user level users can issue this command. Example to configure stp mst ports: dgs-36...

  • Page 1086

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1081 example to enable an ssh server public key algorithm: dgs-3620-28sc:admin#config ssh algorithm dsa enable command: config ssh algorithm dsa enable success. Dgs-3620-28sc:admin# 96-2 show ssh algorithm descripti...

  • Page 1087

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1082 public key algorithm -------------------------- rsa : enabled dsa : enabled dgs-3620-28sc:admin# 96-3 config ssh authmode description this command is used to update the user authentication for ssh configuration...

  • Page 1088

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1083 parameters none. Restrictions none. Example to display the ssh user authentication method: dgs-3620-28sc:admin#show ssh authmode command: show ssh authmode the ssh authentication method: password : enabled publ...

  • Page 1089

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1084 example to update user “danilo” in authentication mode: dgs-3620-28sc:admin#config ssh user danilo authmode publickey command: config ssh user danilo authmode publickey success. Dgs-3620-28sc:admin# 96-6 show s...

  • Page 1091

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1086 restrictions only administrator, operator and power-user level users can issue this command. Example to enable ssh: dgs-3620-28sc:admin#enable ssh command: enable ssh success. Dgs-3620-28sc:admin# 96-9 disable ...

  • Page 1092

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1087 format show ssh server parameters none. Restrictions none. Example to show ssh server: dgs-3620-28sc:admin#show ssh server command: show ssh server the ssh server configuration maximum session : 8 connection ti...

  • Page 1093

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1088 restrictions only administrator, operator and power-user level users can issue this command. Example to disable the secondary username/password authentication for users using ssh public key authentication: dgs-...

  • Page 1094

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1089 dgs-3620-28sc:admin#download ssh client_pub_key 169.168.10.100 src_file id_rsa_keys command: download ssh client_pub_key 169.168.10.100 src_file id_rsa_keys connecting to server................... Done. Downloa...

  • Page 1096

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1091 keyfilename pkey.Der command: download ssl certificate 10.55.47.1 certfilename cert.Der keyfilename pkey.Der success. Dgs-3620-28sc:admin# 97-2 enable ssl description this command is used to enable the ssl stat...

  • Page 1097

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1092 note: web will be disabled if ssl is enabled. Success. Dgs-3620-28sc:admin# 97-3 disable ssl description this command is used to disable the ssl feature and supported ciphersuites. Format disable ssl {ciphersui...

  • Page 1099

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1094 format show ssl cachetimeout parameters none. Restrictions none. Example to show the ssl cache timeout: dgs-3620-28sc:admin# show ssl cachetimeout commands: show ssl cachetimeout cache timeout is 600 second(s) ...

  • Page 1100

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1095 dgs-3620-28sc:admin# config ssl cachetimeout 60 commands: config ssl cachetimeout 60 success. Dgs-3620-28sc:admin# 97-7 config ssl certificate chain description this command is used to specify chain of certific...

  • Page 1101

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1096 restrictions only administrator-level users can issue this command. Example to delete a certificate: dgs-3620-28sc:admin#delete ssl certificate web_ca2.Cer command: delete ssl certificate web_ca2.Cer success. D...

  • Page 1103

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1098 stacking is stable, master’s priority will become zero. If stacking topology change again, master will use priority zero and mac address to determine who new primary master is. Format config stacking force_mast...

  • Page 1104

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1099 dgs-3620-28sc:admin# show stacking_mode command: show stacking_mode stacking mode : enabled dgs-3620-28sc:admin# 98-4 show stack_information description this command displays stacking information. Format show s...

  • Page 1105

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1100 7 - not_exist no 8 - not_exist no dgs-3620-28sc:admin# 98-5 show stack_device description this command displays stack device information. Format show stack_device parameters none. Restrictions none. Example to ...

  • Page 1106

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1101 parameters - enter the current box id value used here. This value must be between 1 and 12. New_box_id - specifies the new id assigned to the box. Auto - specifies that the box id to be assigned automatically b...

  • Page 1108

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1103 example to enable the stacking trap state: dgs-3620-28sc:admin# config stacking trap state enable command: config stacking trap state enable success. Dgs-3620-28sc:admin#.

  • Page 1111

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1106 vlan - (optional) specify the vlan associated with the mac address. - enter the vlan name. The maximum length is 32 characters. Vlanid - (optional) specify the vlan id associated with the mac address. - enter t...

  • Page 1113

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1108 dgs-3620-28sc:admin# create ipmroute 11.0.0.0/8 rpf_address 20.1.2.3 command: create ipmroute 11.0.0.0/8 rpf_address 20.1.2.3 success. Dgs-3620-28sc:admin# 100-2 delete ipmroute description this command is used...

  • Page 1114

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1109 restrictions none. Example to display ip multicast static route entry: dgs-3620-28sc:admin# show ipmroute 11.0.0.0/8 command: show ipmroute 11.0.0.0/8 index source ip address rpf ip address ----- --------------...

  • Page 1116

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1111 dgs-3620-28sc:admin#create subnet_vlan network 172.168.1.1/24 vlan v2 priority 2 command: create subnet_vlan network 172.168.1.1/24 vlan v2 priority 2 success . Dgs-3620-28sc:admin# to create an ipv6 subnet vla...

  • Page 1117

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1112 success. Dgs-3620-28sc:admin# to delete all subnet vlan entries: dgs-3620-28sc:admin#delete subnet_vlan all command: delete subnet_vlan all success. Dgs-3620-28sc:admin# 101-3 show subnet_vlan description this ...

  • Page 1118

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1113 dgs-3620-28sc:admin# to display a specied ipv6 subnet vlan entry: dgs-3620-28sc:admin# show subnet_vlan ipv6network fe80:250:baff::0/64 command: show subnet_vlan ipv6network fe80:250:baff::0/64 ip address/subne...

  • Page 1119

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1114 subnet_vlan - specifies that the subnet vlan classification is precedence than mac-based vlan classification restrictions only administrator, operator and power-user level users can issue this command. Example ...

  • Page 1120

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1115.

  • Page 1122

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1117 example to create super vlan 10: dgs-3620-28sc:admin# create super_vlan vlanid 10 command: create super_vlan vlanid 10 success. Dgs-3620-28sc:admin# 102-2 config super_vlan description this command is used to c...

  • Page 1124

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1119 ip_range - specifies the ip range of the sub-vlan that will be used. - enter the starting ip address used here. To - specifies that the next ip address will be the ending ip address. - enter the ending ip addre...

  • Page 1125

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1120 dgs-3620-28sc:admin# show super_vlan command: show super_vlan super vid : 3 vlan name : super3 ip subnet: 172.6.0.254/16 status : inactive sub vid : 200-204 total entries: 1 dgs-3620-28sc:admin# 102-6 show sub_...

  • Page 1126

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1121 dgs-3620-28sc:admin# show sub_vlan command: show sub_vlan sub vid status super vid ip range ------- ------- ---------- ------------------------ 1 active 10 10.1.1.1-10.1.1.10 10.1.2.1-10.1.2.20 2 active 10 10.1...

  • Page 1128

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1123 offline - specifies that a local device may indicate offline prior to powering off, running transmitter tests, or removing the local device from the active configuration. If it is set and detected offline, it w...

  • Page 1130

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1125 1:2 enabled auto/disabled link down enabled auto description: 1:3 enabled auto/disabled link down enabled auto description: 1:4 enabled auto/disabled link down enabled auto description: ctrl+c esc q quit space ...

  • Page 1132

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1127 success. Dgs-3620-28sc:admin# 104-2 show system_severity description this command is used to show the severity level control for a system. Format show system_severity parameters none. Restrictions none. Example...

  • Page 1133: Chapter 105

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1128 chapter 105 tech support commands show tech_support upload tech_support_totftp 105-1 show tech_support description this command is used to display technical support information. It is especially useful for tech...

  • Page 1134

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1129 #----------------------------------------------------------------------------- ******************** basic system information ******************** [sys 2000-1-24 03:05:29] boot time : 24 jan 2000 03:01:12 rtc ti...

  • Page 1135

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1130 parameters - enter the ipv4 address of the tftp server. - enter the file name of the technical support information file sent to the tftp server. The maximum size of the file name is 64 characters. Restrictions ...

  • Page 1138

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1133 restrictions none. Example to show sntp: dgs-3620-28sc:admin#show sntp command: show sntp current time scource : system clock sntp status : disabled ipv4 primary sntp server : none ipv4 secondary sntp server: n...

  • Page 1139

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1134 106-5 disable sntp description this command is used to turn off sntp support. Format disable sntp parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Ex...

  • Page 1140

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1135 dgs-3620-28sc:admin# config time 30jun2003 16:30:30 command: config time 30jun2003 16:30:30 success. Dgs-3620-28sc:admin# 106-7 config time_zone description this command is used to change time zone settings. Fo...

  • Page 1142

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1137 example to configure time: dgs-3620-28sc:admin#config dst repeating s_week 2 s_day tue s_mth 4 s_time 15:00 e_week 2 e_day wed e_mth 10 e_time 15:30 offset 30 command: config dst repeating s_week 2 s_day tue s_...

  • Page 1144

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1139 format show traffic_segmentation {} parameters - (optional) specify a range of ports to be displayed. Note: if no parameter is specified, the system will display all current traffic segmentation tables. Restric...

  • Page 1146

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1141 format disable udp_helper parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable the udp helper function: dgs-3620-28sc:admin# disable u...

  • Page 1147

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1142 dgs-3620-28sc:admin# config udp_helper add ipif system 20.0.0.90 command: config udp_helper add ipif system 20.0.0.90 success. Dgs-3620-28sc:admin# 108-4 config udp_helper delete ipif description this command i...

  • Page 1148

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1143 parameters time - specifies the time service. The udp port number is 37. Tacacs - specifies the terminal access controller access control system service. The udp port number is 49. Dns - specifies the domain na...

  • Page 1149

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1144 example to delete a udp port: dgs-3620-28sc:admin# config udp_helper udp_port delete 55 command: config udp_helper udp_port delete 55 success. Dgs-3620-28sc:admin# 108-7 show udp_helper description this command...

  • Page 1150

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1145 dgs-3620-28sc:admin#show udp_helper udp_port command: show udp_helper udp_port udp helper status : enabled application udp port ------------ --------------- user app1 55 dgs-3620-28sc:admin# to display the curr...

  • Page 1152

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1147 example to add urpf checking on ports 1-8 with strict mode and enable the default route check option: dgs-3620-28sc:admin#config ip urpf ports 1:1-1:8 mode strict default_route_check state enable command: confi...

  • Page 1153

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1148 109-3 disable ip urpf description this command is used to disable the ip urpf feature. When disabled, the hardware routing table needs not to be searched using sip any more. So the whole hardware routing table ...

  • Page 1154

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1149 restrictions none. Example to display the urpf settings of all the ports: dgs-3620-28sc:admin#show ip urpf command: show ip urpf urpf global state : disabled port mode default route check port mode default rout...

  • Page 1155

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1150 example to remove urpf checking from all ports. Dgs-3620-28sc:admin#delete ip urpf ports all command: delete ip urpf ports all success. Dgs-3620-28sc:admin#.

  • Page 1158

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1153 - enter an absolute path name on the device. Restrictions only administrator-level users can issue this command. Example to download runtime firmware from a tftp server: dgs-3620-28sc:admin#download firmware_fr...

  • Page 1159

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1154 restrictions only administrator-level users can issue this command. Example to download a configuration file from an rcp server: dgs-3620-28sc:admin#download cfg_fromrcp username rcp_user 172.18.212.106 src_fil...

  • Page 1160

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1155 example to download firmware from an rcp server: dgs-3620-28sc:admin#download firmware_fromrcp username rcp_user 10.90.90.90 src_file /home/dgs-3620.Had command: download firmware_fromrcp username rcp_user 10.9...

  • Page 1161

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1156 begin - (optional) the first line that contains the specified filter string will be the first line of the output. - enter a filter string enclosed by the quotation mark symbol. Thus, the filter string itself ca...

  • Page 1162

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1157 to upload the current configuration file to a tftp server: dgs-3620-28sc:admin#upload cfg_totftp 10.48.74.121 dest_file c:\cfg\dgs- 3620.Cfg command: upload cfg_totftp 10.48.74.121 dest_file c:\cfg\dgs-3620.Cfg...

  • Page 1163

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1158 - (optional) enter the ip address used for the configuration here. Dest_file – specifies the destination file used. - the pathname specifies the pathname on the rcp server or local device. Rcp: - syntax: rcp: u...

  • Page 1164

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1159 - enter the path name on the rcp server or local rcp client. Rcp: - specifies the path on the rcp server or local rcp client. Note: if a user specifies the relative file path, the path search strategy will depe...

  • Page 1165

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1160 dest_file - specifies the path name on the rcp server. Note: if a user specifies the relative file path, the path search strategy will depend on the server system. For some systems, the current user working dir...

  • Page 1166

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1161 path, the path search strategy will depend on the server system. For some systems, the current user working directory will be searched first, followed by the environment paths. - enter the path name of the rcp ...

  • Page 1167

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1162 - enter the unit id used for this configuration here. - enter a firmware on the device file system. Boot_up - specifies as a boot-up file. Restrictions only administrator-level users can issue this command. Exa...

  • Page 1168

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1163 110-11 show config description this command is used to display configuration information. The output stream of the configuration data can be filtered by the expression specified at the end of the command. The e...

  • Page 1169

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1164 # firmware: build 2.50.014 # copyright(c) 2013 d-link corporation. All rights reserved. #----------------------------------------------------------------------------- # stack config stacking force_master_role s...

  • Page 1170

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1165 110-13 config rcp server description this command is used to configure remote copy protocol (rcp) global server information. This global rcp server setting can be used when the server or remote user name is not...

  • Page 1171

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1166 restrictions only administrator-level users can issue this command. Example to clear the current username of the rcp global server: dgs-3620-28sc:admin#config rcp server clear username command: config rcp serve...

  • Page 1173

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1168 parameters - enter the ipv6 address of the host. - enter the domain name of the host. This name can be up to 255 characters long. Times - (optional) specify the number of individual icmp echo messages to be sen...

  • Page 1177

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1172 format enable broadcast_ping_reply parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to enable broadcast ping reply state: dgs-3620-28sc:admin...

  • Page 1178

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1173 110-23 show broadcast_ping_reply description the show broadcast_ping_reply command is used to show the broadcast ping reply state. Format show broadcast_ping_reply parameters none. Restrictions none. Example to...

  • Page 1179

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1174 example to configure the ip 10.90.90.90 on the system interface as the source address: dgs-3620-28sc:admin#config telnet source_ipif system 10.90.90.90 command: config telnet source_ipif system 10.90.90.90 succ...

  • Page 1181

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1176 ip interface : system ipv4 address : 10.90.90.90 ipv6 address : none dgs-3620-28sc:admin#.

  • Page 1183

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1178 111-2 disable vrrp description this command is used to disable vrrp globally. Format disable vrrp {ping} parameters ping - (optional) specifies that the ping option will be disabled. Restrictions only administr...

  • Page 1184

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1179 priority - (optional) specifies the priority to be used for the virtual router master election process - enter the priority value used here. This value must be between 1 and 254. Advertisement_interval - (optio...

  • Page 1185

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1180 parameters vrid - specifies the id of the virtual router used. - enter the virtual router id used here. This value must be between 1 and 255. Ipif - specifies the ip interface used for this configuration. - ent...

  • Page 1187

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1182 parameters vrid - (optional) specifies the virtual router id used. - enter the virtual router id used here. This value must be between 1 and 255. Ipif - (optional) specifies the ip interface name used. - enter ...

  • Page 1188

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1183 dgs-3620-28sc:admin# show vrrp command: show vrrp global vrrp : disabled non-owner response ping: disabled interface name : system authentication type : no authentication vrid : 1 virtual ip address : 10.90.90....

  • Page 1190

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1185 dgs-3620-28sc:admin#enable voice_vlan v2 command: enable voice_vlan v2 success . Dgs-3620-28sc:admin# 112-2 disable voice_vlan description this command is used to disable the voice vlan function on a switch. Wh...

  • Page 1191

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1186 restrictions only administrator, operator and power-user level users can issue this command. Example to set the priority of the voice vlan to be six: dgs-3620-28sc:admin#config voice_vlan priority 6 command: co...

  • Page 1192

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1187 restrictions only administrator, operator and power-user level users can issue this command. Example to add a user-defined oui of a voice device: dgs-3620-28sc:admin#config voice_vlan oui add 00-0a-0b-00-00-00 ...

  • Page 1193

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1188 dgs-3620-28sc:admin#config voice_vlan ports 4-6 state enable command: config voice_vlan ports 4-6 state enable success. Dgs-3620-28sc:admin# to set voice vlan ports 4 to 6 to auto mode: dgs-3620-28sc:admin#conf...

  • Page 1194

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1189 timer will be started. The port will be removed from the voice vlan after expiration of voice vlan aging timer. If the voice traffic resumes during the aging time, the aging timer will be reset and stop. Format...

  • Page 1195

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1190 dgs-3620-28sc:admin#show voice_vlan command: show voice_vlan voice vlan state : disabled voice vlan : unassigned priority : 5 aging time : 720 minutes log state : enabled dgs-3620-28sc:admin# 112-9 show voice_v...

  • Page 1196

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1191 remain time : 120 seconds total entries: 2 dgs-3620-28sc:admin# 112-10 show voice_vlan oui description this command is used to display the oui information for voice vlan. Format show voice_vlan oui parameters n...

  • Page 1197

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1192 format show voice_vlan ports {} parameters - (optional) specify a range of ports to display. Note: if no parameter is specified, all voice vlan port information will be displayed. Restrictions none. Example to ...

  • Page 1198

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1193 example to display voice vlan device ports 1 to 2: dgs-3620-28sc:admin#show voice_vlan voice_device ports 1-2 command: show voice_vlan voice_device ports 1-2 ports voice device start time last active time -----...

  • Page 1200

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1195 restrictions only administrator, operator and power-user level users can issue this command. Example to create a vlan with the name “v2” and vlan id 2: dgs-3620-28sc:admin#create vlan v2 tag 2 type 1q_vlan adve...

  • Page 1201

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1196 success. Dgs-3620-28sc:admin# to create a private vlan with vlan id 3: dgs-3620-28sc:admin#create vlan vlanid 3 type private_vlan command: create vlan vlanid 3 type private_vlan success. Dgs-3620-28sc:admin# 11...

  • Page 1202

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1197 format delete vlan vlanid parameters - enter a range of vlan id to be deleted. Restrictions only administrator, operator and power-user level users can issue this command. Example to remove a vlan id 2: dgs-362...

  • Page 1203

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1198 example to add 4 through 8 as tagged ports to the vlan v1: dgs-3620-28sc:admin#config vlan v1 add tagged 4-8 command: config vlan v1 add tagged 4-8 success. Dgs-3620-28sc:admin# to delete ports 4 through 8 from...

  • Page 1204

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1199 enable - specifies to enable gvrp. Disable - specifies to disable gvrp. Name - specifies the vlan name. - the maximum length is 32 characters. Restrictions only administrator, operator and power-user level user...

  • Page 1205

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1200 parameters - enter a range of ports to be set. All - specifies to make all ports to be set. Gvrp_state - specifies if the port is allowed to dynamically become a member of a vlan when receiving gvrp. Enable - e...

  • Page 1206

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1201 restrictions none. Example to display 802.1q port settings for ports 1 to 3: dgs-3620-28sc:admin#show port_vlan 1-3 command: show port_vlan 1-3 port pvid gvrp ingress checking acceptable frame type ------- ----...

  • Page 1207

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1202 dgs-3620-28sc:admin#config gvrp timer join 200 command: config gvrp timer join 200 success. Dgs-3620-28sc:admin# 113-10 enable gvrp description this command is used to enable the generic vlan registration proto...

  • Page 1208

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1203 restrictions only administrator, operator and power-user level users can issue this command. Example to disable generic vlan registration protocol (gvrp): dgs-3620-28sc:admin#disable gvrp command: disable gvrp ...

  • Page 1209

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1204 static untagged ports : 1-28 forbidden ports : total static vlan entries: 1 total gvrp vlan entries: 0 dgs-3620-28sc:admin# 113-13 show vlan vlanid description this command is used to display summary informatio...

  • Page 1210

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1205 113-14 show vlan ports description this command is used to display summary information about tagged, untagged, and forbidden status for each port. Format show vlan ports {} parameters - (optional) specify a ran...

  • Page 1211

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1206 example to display the gvrp status of the switch: dgs-3620-28sc:admin#show gvrp command: show gvrp global gvrp : disabled join time : 200 milliseconds leave time : 600 milliseconds leaveall time : 10000 millise...

  • Page 1212

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1207 - enter the vlan id. Restrictions only administrator, operator and power-user level users can issue this command. Example to associate secondary vlan to private vlan p1: dgs-3620-28sc:admin#config private_vlan ...

  • Page 1213

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1208 community ports : 9-10 community vlan: 40 private vlan 200 ------------------ promiscuous ports: 11 trunk ports : 12 isolated ports : 13-15 isolated vlan : 50 community ports : 16-18 community vlan: 60 dgs-3620...

  • Page 1214

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1209 113-19 disable pvid auto_assign description the command is used to disable the auto-assignment of pvid. If auto-assign pvid is disabled, pvid can only be changed by pvid configuration (user changes explicitly)....

  • Page 1215

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1210 example to display the pvid auto-assignment state: dgs-3620-28sc:admin#show pvid auto_assign pvid auto-assignment: enabled. Dgs-3620-28sc:admin#.

  • Page 1217

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1212 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable vlan trunking: dgs-3620-28sc:admin#disable vlan_trunk command: disable vlan_trunk...

  • Page 1218

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1213 example to configure ports 1 to 5 as vlan trunking ports: dgs-3620-28sc:admin#config vlan_trunk ports 1-5 state enable command: config vlan_trunk ports 1-5 state enable success. Dgs-3620-28sc:admin# to configur...

  • Page 1219

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1214 dgs-3620-28sc:admin# config vlan_trunk ports 6-7 state disable command: config vlan_trunk ports 6-7 state disable success. Dgs-3620-28sc:admin# 114-4 show vlan_trunk description this command is used to display ...

  • Page 1221

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1216 example to enable the wac function: dgs-3620-28sc:admin#enable wac command: enable wac success. Dgs-3620-28sc:admin# 115-2 disable wac description this command is used to disable the wac function. Format disabl...

  • Page 1222

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1217 parameters radius - if specified to enable, the authorized data assigned by the raduis server will be accepted if the global authorization network is enabled. The default state is enabled. Enable - specifies to...

  • Page 1223

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1218 before it can be re-authenticated.The default value is 60 seconds. - enter a block time between 0 and 300 seconds. Restrictions only administrator, operator and power-user level users can issue this command. Ex...

  • Page 1224

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1219 dgs-3620-28sc:admin#config wac method radius command: config wac method radius success. Dgs-3620-28sc:admin# 115-6 config wac default_redirpath description this command is used to configure the wac default redi...

  • Page 1225

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1220 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to clear the wac default redirect path: dgs-3620-28sc:admin#config wac clear_default_redirpa...

  • Page 1226

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1221 115-9 config wac switch_http_port description this command is used to configure the tcp port which the wac switch listens to. The tcp port for http or https is used to identify the http or https packets that wi...

  • Page 1227

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1222 characters long. Vlanid - (optional) specify the authentication vlan id number. - enter the authentication vlan id number. The vlan id must be between 1 and 4094. Restrictions only administrator, operator and p...

  • Page 1229

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1224 restrictions none. Example to show wac: dgs-3620-28sc:admin# show wac command: show wac web-based access control ----------------------------- state : enabled method : radius redirect path : http://www.Dlink.Co...

  • Page 1230

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1225 dgs-3620-28sc:admin# show wac ports 1-3 command: show wac ports 1-3 port state aging time idle time block time (min) (min) (sec) ------- -------- ------------ ---------- ----------- 1 disabled 1440 infinite 60 ...

  • Page 1231

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1226 format show wac auth_state ports {} parameters - (optional) specify the list of ports whose wac authentication state will be displayed. Restrictions none. Example to display the wac authentication status of por...

  • Page 1232

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1227 - enter the mac address here. Restrictions only administrator, operator and power-user level users can issue this command. Example to clear the wac authentication state of ports 1 to 5: dgs-3620-28sc:admin# cle...

  • Page 1233

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1228 example to customize the authenticate page elements: dgs-3620-28sc:admin# config wac authentication_page element notification_line 1 copyright @ 2011 d-link all rights reserved command: config wac authenticatio...

  • Page 1235

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1230 116-2 disable wred description this command is used to disable the wred global state. Format disable wred parameters none. Restrictions only administrator, operator and power-user level users can issue this com...

  • Page 1236

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1231 dgs-3620-28sc:admin#create wred profile 2 profile_name profilename command: create wred profile 2 profile_name profilename success. Dgs-3620-28sc:admin# 116-4 config wred profile description this command is use...

  • Page 1237

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1232 dgs-3620-28sc:admin#config wred profile profile_id 2 min_threshold 30 max_threshold 50 max_drop_rate 10 command: config wred profile profile_id 2 min_threshold 30 max_threshold 50 max_drop_rate 10 success. Dgs-...

  • Page 1238

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1233 dgs-3620-28sc:admin#config wred ports 1:1 cos 2 profile profile_id 2 command: config wred ports 1:1 cos 2 profile profile_id 2 success. Dgs-3620-28sc:admin# 116-6 delete wred profile description this command is...

  • Page 1239

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1234 - (optional) enter a range of ports. Restrictions none. Example to display wred of port 1:1 and 1:2 settings: dgs-3620-28sc:admin#show wred ports 1:1-1:2 command: show wred ports 1:1-1:2 global wred : disabled ...

  • Page 1240

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1235 parameters default - (optional) specify the default profile to be displayed. Profile_id - (optional) specify the profile id to be displayed. - enter the profile id between 2 and 128. - (optional) specify the pr...

  • Page 1241: Appendix A

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1236 appendix a password recovery procedure this chapter describes the procedure for resetting passwords on d-link switches. Authenticating any user who tries to access networks is necessary and important. The basic...

  • Page 1242

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1237 command parameters force_agree - specifies to forcibly agree with the command. Reset account the reset account command deletes all the previously created accounts. Reset password {} the reset password command r...

  • Page 1243: Appendix B

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1238 appendix b system log entries the following table lists all possible entries and their corresponding meanings that will appear in the system log of this switch. Category log description severity note mac-based ...

  • Page 1244

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1239 portnum: the port number. Vid: the vlan id on which the host exists. Ptp event description: ptp port role changed log message: ptp port role changed to . Parameters description: unitid: the unit id. Portnum: th...

  • Page 1245

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1240 parameters description: ipv6address: ipv6 address obtained from a dhcpv6 server. Ipif-name: name of the dhcpv6 client interface. Event description: dhcpv6 client pd interface administrator state changed. Log me...

  • Page 1246

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1241 name> is used up. Parameters description: : name of the dhcpv6 server pool. Event description: the number of allocated ipv6 addresses is equal to 4096 log message: the number of allocated ipv6 addresses of the ...

  • Page 1247

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1242 username: represent current login user. Ipaddr: represent client ip address. Macaddr : represent client mac address. Event description: configuration download unsuccessfully. Log message: configuration download...

  • Page 1248

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1243 username: represent current login user. Ipaddr: represent client ip address. Macaddr : represent client mac address. Event description: attack log message uploaded successfully. Log message: attack log message ...

  • Page 1249

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1244 username: represent current login user. Ipaddr: represent client ip address. Macaddr : represent client mac address. Event description: configuration download was unsuccessful. Log message: configuration downlo...

  • Page 1250

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1245 username: represent current login user. Ipaddr: represent client ip address. Macaddr : represent client mac address. Dns resolver event description: duplicate domain name cache added, leads a dynamic domain nam...

  • Page 1251

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1246 stacking system. Portnum: 1.Interger value;2.Represent the logic port number of the device. 802.1x event description: 802.1x authentication failure. Log message: 802.1x authentication failure [for ] from (usern...

  • Page 1252

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1247 parameters description: ipaddr: the ip address of the radius server. Priority: priority of radius assign. Unitid: the unit id. Portnum: the port number. Username: the user that is being authenticated. Event des...

  • Page 1253

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1248 4. Networkaddress(4) 5. Interfacename(5) 6. Agentcircuitid(6) 7. Local(7) portid: port id. Deviceclass: lldp-med device type. Event description: incompatible lldp-med tlv set detected log message: incompatible ...

  • Page 1254

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1249 parameters description: ipaddr: ip address of bgp peer. Event description: bgp connection is normally closed. Log message:[bgp(2):] bgp connection is normally closed(peer:). Parameters description: ipaddr: ip a...

  • Page 1255

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1250 ipaddr: ip address of bgp peer. Event description: bgp received unnecessary as4-aggregator attribute from new (4-bytes as) bgp peer log message: [bgp(11):] received as4-aggregator attribute from new (4-bytes as...

  • Page 1256

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1251 conflict (mac: and mac: ). Parameters description: unitid: box id. Macaddr: the mac addresses of the conflicting boxes. Snmp event description: snmp request received with invalid community string log message: s...

  • Page 1257

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1252 nbr-id: neighbor's router id. Event description: ospf router id was changed. Log message: ospf router id changed to parameters description: router-id: ospf router id. Informational event description: enable osp...

  • Page 1258

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1253 vr-id: vrrp virtual router id. Intf-name: interface name on which virtual router is based. Event description: a virtual mac address is added into switch l2 table log message: added a virtual mac into l2 table p...

  • Page 1259

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1254 parameters description: vrrp-ip-addr: vrrp virtual ip address vrrp-mac-addr: vrrp virtual mac address mac-intf: interface id on which vrrp virtual mac address is based. Event description: failed when adding a v...

  • Page 1260

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1255 log message: login failed through web(ssl) (username: , ip: ). Parameters description: username: the use name that used to login ssl server. Ipaddr: the ip address of ssl client. Event description: web(ssl) ses...

  • Page 1261

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1256 ssh> (username: , ip: ). Parameters description: ipaddr: ip address. Username: user name. Ipv6address: ipv6 address. Event description: logout. Log message: logout through (username: , ip: ). Parameters descrip...

  • Page 1263

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1258 jwac event description: when a client host authenticated successful. Log message: jwac authenticated user (username: , ip: , mac: , port: ) parameters description: string: username ipaddr: ip address macaddr: m...

  • Page 1264

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1259 , mac: , port ) parameters description: ipaddr: ip address macaddr: mac address unitid: the unit id portnum : the port number event description: dynamic impb entry conflicts with static fdb. Log message: dynami...

  • Page 1265

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1260 event description: broadcast storm cleared. Log message: port broadcast storm has cleared. Parameters description: portnum: the port number. Informational event description: multicast storm occurrence. Log mess...

  • Page 1266

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1261 port log message: [duld(1):] port: portnum> is unidirectional. Parameters description: unitid: the unit id portnum: port number mstp debug enhancement event description: topology changed. Log message: topology ...

  • Page 1267

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1262 instanceid: instance id. Event description: spanning tree version changed. Log message: spanning tree version changed. New version: parameters description: new_version: new stp version. Informational event desc...

  • Page 1268

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1263 note: in cfm hardware mode, remote mep information (mepid and macaddr) is unknown. Event description: cannot receive the remote mep's ccm packet log message: cfm remote down. Md level:, vlan:, local(port , dire...

  • Page 1269

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1264 mepdirection: represents the direction of the mep. This can be "inward" or "outward". Mepid: represents the mepid of the mep. Event description: lck condition detected log message: lck condition detected. Md le...

  • Page 1270

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1265 event description: bpdu attack automatically recover. Log message: port recover from bpdu under protection state automatically parameters description: unitid: the unit id. Portnum: the port number. Informationa...

  • Page 1271

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1266 logged before 30 days. Log message: license will expire in 30 days. (license: model>, ac: ). Parameters description: : license model name. : activation code model>, ac: ). Parameters description: : license mode...

  • Page 1272: Appendix C

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1267 appendix c trap entries this table lists the trap logs found on the switch. Category trap name description oid mac notification swl2macnotification this trap indicates the mac addresses variation in address tab...

  • Page 1273

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1268 binding objects: (1) pimgroupmappingpimmode (2) piminvalidjoinpruneaddresstype (3) piminvalidjoinpruneorigin (4) piminvalidjoinprunegroup (5) piminvalidjoinprunerp (6) pimneighboruptime pimrpmappingchage a pimr...

  • Page 1274

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1269 detected. Binding objects: (1) dot3oameventlogtimestamp (2) dot3oameventlogoui (3) dot3oameventlogtype (4)dot3oameventloglocation (5)dot3oameventlogeventtotal upload/download agentfirmwareupgrade this trap is s...

  • Page 1275

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1270 (2) swunitmgmtid vrrp vrrptrapnewmaster the newmaster trap indicates that the sending agent has transitioned to 'master' state. Binding objects: (1) vrrpopermasteripaddr 1.3.6.1.2.1.68.0.1 vrrptrapauthfailure a...

  • Page 1276

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1271 (2) swipmacbindingviolationip (3) swipmacbindingviolationmac swipmacbindingipv6violationtrap when the ip-mac binding trap is enabled, if there's a new mac that violates the pre- defined ipv6 impb configuration,...

  • Page 1277

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1272 blocking state. The trap is not sent if a newroot trap is sent for the same transition. Implementation of this trap is optional cfm dot1agcfmfaultalarm this trap is initiated when a connectivity defect is detec...

  • Page 1278

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1273 (1) swddmport (2) swddmthresholdtype (3) swddmthresholdexceedtype (4) swddmthresholdexceedorrecover external alarm swexternalalarm when external alarm occurred. Binding objects： (1) swexternalalarmchannel (2) s...

  • Page 1279

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1274 2:swtempersensorid 3:swtemperaturecurrent swtemperaturelowrecover temperature low recover notification. Binding objects： 1:swtemperatureunitindex 2:swtempersensorid 3:swtemperaturecurrent 1,3,6,1,4,1,171,12,11,...

  • Page 1280

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1275 swsingleipmslinkup the commander switch will send this notification when its member generates a link up notification. Binding objects: (1) swsingleipmsid (2) swsingleipmsmacaddr (3) ifindex 1.3.6.1.4.1.171.12.8...

  • Page 1281

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1276 power recover notification. Binding objects: (1) swsingleipmsid (2) swsingleipmsmacaddr (3) swsingleipmstrapmessage.

  • Page 1282: Appendix D

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1277 appendix d radius attributes assignment the radius attributes assignment on the switch is used in the following modules: 802.1x (port- based and host-based), japanese web-based access control, web-based access ...

  • Page 1283

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1278 vendor-specific attribute description value usage vendor-id defines the vendor. 171 (dlink) required vendor-type defines the attribute. 4 required attribute-specific field used to assign the 802.1p default prio...

  • Page 1284

    Xstack® dgs-3620 series layer 3 managed stackable gigabit switch cli reference guide 1279 0x1f, >0x1f) the vlan id first. In other words, the switch will check all existed vlan id and check if there is one matched. 2. If the switch can find one matched, it will move to that vlan. 3. If the switch ca...