- DL manuals
- D.T.Systems
- Pet Care Product
- CDT 1000 PLUS
- Owner's Manual
D.T.Systems CDT 1000 PLUS Owner's Manual
Summary of CDT 1000 PLUS
Page 1
Cdt plus series electronic dog trainer owner’s manual • cdt 1000 plus • cdt 2000 plus manufactured by:.
Page 2
2.
Page 3: Table of Contents
3 table of contents • table of contents ....................................... 3 • introduction ................................................ 4 • package contents ...................................... 5 • model features .......................................... 5 • parts & functions .............
Page 4: Introduction
4 congratulations and thank you for purchasing our cabela’s exclusive alpha dog series cdt plus training collar with “add-on” capability. The cabela’s alpha dog series represents the absolute latest technological advancement in the electronic dog training world. It offers maxx-range™, the industry’s...
Page 5: Package Contents
5 package contents • transmitter • collar receiver • antenna for the transmitter • rechargeable nimh batteries for both the collar and transmitter (already installed) • battery charger • splitter cable for simultaneous charging • test light • owner’s manual model features cdt plus series • digital t...
Page 6: Transmitter
6 transmitter parts & functions button #2* (vib.+stim.) battery charging receptacle intensity dial collar selecting switch momentary ‘nick’ stimulation continuous stimulation red led indicator light button #1* (vibration) *the cdt 1000 plus will not have the #1 or #2 buttons. Lanyard loop transmitte...
Page 7: Parts & Functions
7 parts & functions intensity selection dial the intensity selection dial can be set from level 1 to level 16 to find the exact stimulation level for your dog (see page 15). Transmitter antenna always check that the antenna is securely fastened to the transmitter before each use. Hand tighten only. ...
Page 8: Parts & Functions
8 parts & functions caution if your collar belt is too long , we recommend looping the excess collar belt back around through the buckle. We do not recommend cutting the collar belt. Cutting the collar belt too much will drastically reduce the range of your collar unit. However, the collar belt can ...
Page 9: Parts & Functions
9 parts & functions collar led indicator light when the collar receiver is turned on, the red led light will flash steadily once every two seconds to indicate that the unit is active. The red led light changes to a rapid flash when the battery is in need of charging. The red led light stays lit whil...
Page 10: Charging The Batteries
10 charging the batteries all cdt plus seriesunits are equipped with rechargeable nickel metal hydride (nimh) batteries. Nimh batteries are not memory sensitive and do not require depletion before recharging. The batteries come partially charged from the factory. However, it is recommended that the ...
Page 11: Turning On and Off
11 turning on and off the transmitter is always in a permanent sleep state. It is only on when a button is being pressed and does not need to be turned off by the user. Turning the collar unit on: press and hold the on/off button. The red led indicator will light solid for a second. Release the butt...
Page 12: To Test The Vibration:
12 to test the vibration: (cdt 2000 plus only) a) press the button on the left side of the transmitter (vibrate button) and the collar unit will vibrate only. B) press the button on the right side of the transmitter (vib.+stim. Button) and the unit will vibrate only for 1/2 a second. The tester will...
Page 13: Programming The Collar
13 programming the collar when adding an “add-on” collar, the collar will need to be programmed to the transmitter. If your current collar unit is not responding to the transmitter, it may also need to be reprogrammed to the transmitter. 1. Select the desired collar selecting switch position on the ...
Page 14: Properly Fitting The Collar
14 properly fitting the collar note: proper collar tightness and position are very important to insure safe and consistent collar use. All electronic collars need to be very snug around the dog’s neck to work properly. They must be just tight enough to allow the “contacts” or electrodes to make good...
Page 15: Setting The Intensity Level
15 it is very important to set the correct intensity level on your cdt plus training system before beginning your training sessions to provide the proper level of stimulation without over-stimulating your dog. To do this, place the intensity selection dial so that the system is set on level 1. Turn ...
Page 16: Maintenance
16 maintenance it is very important to periodically clean your cdt plus seriessystems for maximum performance. Regular cleaning will also lengthen the life of your unit. • clean the cdt plus seriescollar box with lukewarm water and a mild anti-bacterial soap. • take care to thoroughly clean the spac...
Page 17: Important Safety Notes
17 important safety notes • before training, your dog should be examined by a veterinarian to assure that your dog is in good health. • never leave your dog unattended with the unit on. Since no electronic device is perfect, there is a very slight possibility that your dog may receive an unintention...
Page 18: Warranty
18 warranty • d.T. Systems premium lifetime warranty is the best warranty offered in the industry. This warranty is free to participating u.S. Customers (a completed warranty registration card must be returned within 30 days of original purchase). This changes our normal one year parts and labor war...
Page 19: Fcc/ic/ce Compliance
19 fcc/ic/ce compliance your cdt plus series tm trainer has been manufactured under complete compliance with part 15 of the federal communication commission (fcc) rules and industry canada (ic) standard rss-310. The complex internal structure of each product has been designed to operate within speci...
Page 20
20 2872 walnut hill lane dallas, texas 75229 tel: (214) 350-9446, (888) 588-8364 fax: (214) 350-7847 website: www.Dtsystems.Com e-mail: customerservice@dtsystems.Com 1-cdt plus 2011.03.29 printed in korea.