- DL manuals
- D.T.Systems
- Pet Care Product
- H2O 1810 PLUS
- Owner's manual
D.T.Systems H2O 1810 PLUS Owner's manual
Summary of H2O 1810 PLUS
Page 1
• h 2 o 1810 plus • h 2 o 1820 plus • h 2 o 1830 plus • h 2 o 1850 plus h 2 o 1800 plus series with smartled owner’s manual.
Page 2: Notice!
2 notice! According to how you use your transmitter, the transmitting range might be much different. You will have more range if you use your transmitter apart from your body as follows: maximum typical range minimum range.
Page 3: Table of Contents
3 table of contents • table of contents ....................................... 3 • introduction ................................................ 4 • package contents ...................................... 5 • model features .......................................... 5 • parts & functions .............
Page 4: Plus Series
4 congratulations and thank you for purchasing our h 2 o plus series tm remote training collar with “add-on” capability, the perfect remote trainer for hunting, basic obedience, and professional training. The collar’s maxx-range™ internal antenna system, the industry’s only internally woven antenna ...
Page 5: Package Contents
5 package contents • transmitter with antenna and lanyard • collar receiver • rechargeable nimh batteries for both the collar and transmitter (already installed) • battery charger • splitter cable for simultaneous charging • test light • owner’s and training manuals • carrying case • digital technol...
Page 6: Transmitter
6 transmitter parts & functions button #2* (function varies according to model) battery charging receptacle collar selecting switch intensity dial smartled indicator light momentary ‘nick’ stimulation button continuous stimulation button button #1* (function varies according to model) *the h 2 o 181...
Page 7: Parts & Functions
7 intensity selection dial - the intensity selection dial can be set from level 1 to level 16 to find the exact stimulation level for your dog (see page 18). Transmitter indicator light - when pressing any of the transmitter buttons, the smartled lights green if there is 51% to 100% charge remaining...
Page 8: Parts & Functions
8 parts & functions buttons #1 & #2 (h 2 o 1830 plus only) - pressing the jump button (#1) makes the collar give a ‘jump’ stimulation, making the intensity level instantly “jump” to a user-programmed intensity level (see page 19). Pressing the rise button (#2) makes the collar give a stimulation tha...
Page 9: Beeper Wire*
9 beeper wire* collar receiver parts & functions contacts - contacts should fit snugly against the dog’s neck to ensure good contact with the skin. For more information on the proper fit of the collar, see page 17. *h 2 o 1850 plus only. All other models will not have beeper horn or beeper wire. Cha...
Page 10: Parts & Functions
10 parts & functions beeper horn (h 2 o 1850 plus only) - the beeper horn is attached to the collar belt. It will emit a loud tone audible from up to 450 yards away. Caution if the collar belt is too long, we recommend looping the ex- cess collar belt back around through the buckle. We do not recomm...
Page 11: Smartled
11 smartled *charging error- if the smartled has a long blink every other second while charging, the rechargeable battery pack may need to be replaced. New batteries may also initially give an error light. Contact d.T. Systems if the problem persists after a few charging sessions. H 2 o 1800 plus se...
Page 12: Charging The Batteries
12 charging the batteries all h 2 o plus series tm units are equipped with rechargeable nickel metal hydride (nimh) batteries, which are not memory sensitive and do not require depletion before recharging. Although batteries come partially charged from the factory, it is recommended that they are gi...
Page 13: Turning On and Off
13 turning on and off the transmitter is always in a permanent sleep state. It is only on when a button is being pressed and does not need to be turned off by the user. Turning the collar unit on: press and hold the on/off button. The smartled indicator will light solid red for one second. Release t...
Page 14: To Test The Vibration:
14 to test the vibration: (h 2 o 1820 plus only) a) press the button on the left side of the transmitter (vibrate button) and the collar unit will vibrate only. B) press the button on the right side of the transmitter (vib.+stim. Button) and the unit will vibrate only for 1/2 a second. The tester wi...
Page 15: Testing
15 testing to test the beeper: (h 2 o 1850 plus only) a) press the button located on the left side of the transmitter (locate button). The collar will beep any time this button is pressed. B) press the button on the right side of the transmitter (run/point button) to activate the run & point mode. P...
Page 16: Programming The Collar
16 programming the collar when adding an “add-on” collar, the collar will need to be programmed to the transmitter. If your current collar unit is not responding to the transmitter, it may also need to be reprogrammed to the transmitter. 1. Select the desired collar selecting switch position on the ...
Page 17: Properly Fitting The Collar
17 properly fitting the collar note: proper collar tightness and position are very important to insure safe and consistent collar use. All electronic collars need to be very snug around the dog’s neck to work properly. They must be just tight enough to allow the “contacts” or electrodes to make good...
Page 18: Setting The Intensity Level
18 it is very important to set the correct intensity level on your h 2 o plus training system before beginning your training sessions to provide the proper level of stimulation without over-stimulating your dog. To do this, place the intensity selection dial so that the system is set on level 1. Tur...
Page 19: Setting The Intensity Level
19 setting the intensity level jump stimulation is a great feature when regularly us- ing two different stimulation levels in training. It is also a great safety tool for emergency situations when your dog is excited and cannot feel or ignores the normal intensity level. Pressing the jump button dir...
Page 20: Maintenance
20 maintenance it is very important to periodically clean your h 2 o plus series tm systems for maximum performance. Regular cleaning will also lengthen the life of your unit. • clean the collar box, belt and buckle with lukewarm water and a mild anti-bacterial soap. • thoroughly clean the space bet...
Page 21: Important Safety Notes
21 important safety notes • before training with this unit, your dog’s health should be examined by a veterinarian. • do not use with aggressive-tempered dogs. • your h 2 o plus series tm collar is a very valuable tool if used correctly. It is extremely important that you completely understand all t...
Page 22: Warranty
22 warranty • d.T. Systems premium lifetime warranty is the best warranty offered in the industry. This warranty is free to participating u.S. Customers (a completed warranty registration card must be returned within 30 days of original purchase). This changes our normal one year parts and labor war...
Page 23: Fcc/ic/ce Compliance
23 fcc/ic/ce compliance your h 2 o 1800 plus series tm trainer has been manufactured under complete compliance with part 15 of the federal communication commission (fcc) rules, industry canada (ic) standard rss-310, and article 3 of the directive 1999/5/ec. The complex internal structure of each pro...
Page 24
24 2872 walnut hill lane dallas, texas 75229 tel: (214) 350-9446, (888) 588-8364 fax: (214) 350-7847 website: www.Dtsystems.Com e-mail: customerservice@dtsystems.Com 1-h 2 o plus 2012.04.12 printed in korea.