1. DL manuals
  2. D-Teg
  3. DVR
  4. BRX2004A
  5. User Manual

D-Teg BRX2004A User Manual

Manual is about: Mobile Digital Video Recorder

Summary of BRX2004A

  • Page 1

    Thank you for purchasing this mobile digital video recorder. Please ensure that you read and understand this user guide and use it before connecting and installing this recorder. Please store the user guide in an easily accessible location. Ver 2.1.0 vdr user guide rsg engineering limited 19 hollies...

  • Page 3: Caution

    3 caution damages due to production malfunction, loss of data, or other damages occurring whil e using this product shall not be the responsibility of the manufacturer. Although the pr oduct is a device used for recording videos, the product may not save all videos in the case of a malfunction. In t...

  • Page 4

    4 gps reception 1. Activate the product in an area without large buildings to improve gps reception. 2. The temperature range for optimum operation of the gps receiver in your car is -10 ~ 50°c. 3. When using the product for the first time or after a long period (more than three days), it may take a...

  • Page 5

    5 contents each brx2004a/2008a order includes the following items. 1. Main unit 2. Gps module with waterproof case 3. Camera input cable 4. Power cable 5. Car signal cable 6. Alarm in/out, video in/out cable 11. Mount/ rear bracket 10. Keys, screws 9. Dvr viewer cd 8. User guide 7. Mini usb cable.

  • Page 6

    6 introduction ① system door lock ② led [power] : green led indicates power-on [rec] : yellow led indicates record-on [alarm] : red led indicates video loss or ssd/hdd failure. [lan] : yellow led indicates network-on ③ removable hdd/ssd: removable lock should be unlocked and power/rec led should be ...

  • Page 7

    7 ⑨ button [ser] : searches the recorded data. [ch] : changes the camera on display. (camera 1 camera 2 camera 3 ->.... ->camera 8 camera 1) [esc] : cancels or exists from the selected modes or menus. [menu] enters into the menu. [fn] : being used in combination with other buttons as follows; fn + u...

  • Page 8

    8 introduction rear ① power connector battery : connects to the battery power in vehicle. Acc : connects to the ignition power in vehicle. ② car signal connector: left/right signals, brake, reverse, speed pulse signal ③ serial port s1 : for problem shooting (debugging) purpose s2(t) : ready for inte...

  • Page 9

    9 connection diagram.

  • Page 10

    10 power on main power switch 1. Turning on the power ① make sure that peripherals are properly connected. ② switch「on」the main power switch on the rear panel as below, ③ turn on the removable hdd/ssd lock using key from [off] to [on] as below, the front power led will light up in green. Please wait...

  • Page 11

    11 power off 2. Turning off the power ① turn off the removable hdd/ssd lock using key from [on] to [off] as below, the record led will be off immediately and the front power led will be off in 15 seconds. ② power led should be off in order to remove the removable hdd/ssd from the dvr. [system shutdo...

  • Page 12

    12 system operation live display camera title video loss, motion detection, audio record, record icons alarm in, alarm out, g-sensor icons storage usage current date & time speed from gps speed from speed pulse press [ch] button to see a single channel display press [right] button to see 4 channels ...

  • Page 13

    13 system operation live display icons video loss, no camera motion detection audio record continuous record (red) event record (yellow) detect alarm in 1 detect alarm in 2 detect alarm in 3 detect alarm in 4 detect alarm in 5 detect alarm in 6 detect alarm in 7 detect alarm in 8 activate alarm out ...

  • Page 14

    14 status to turn off/on the status icons, press [sta] button. Status [sta] button shows, in sequence, the five status information, as below, 1. [all icons] 2. [without icons] 3. [without icons, camera titles] 4. [without all icons] 5. [information] this information page shows the current system inf...

  • Page 15

    15 main menu press [menu] button in front panel brings this screen. The on-screen menus allow you to check the configuration. Only few setting can change here, please use provided dvr viewer to set up all the features of brx. All setup data is safe from power loss and stored in the internal flash me...

  • Page 16

    16 main menu camera brightness, contrast of each channel can be configured in this menu. To change video or camera title, please use dvr viewer. Press [esc] button for returning to the previous mode. Signal speed pulse type and pulse standard can be configured in this menu. Press [esc] button for re...

  • Page 17

    17 main menu g-sensor g-sensor calibration can be configured in this menu. G-sensor(x) 0, 90, 180, 270 -(y) 0, 90, 180, 270 -(z) 0, 90, 180, 270 [example- standard installation] front (x axis): front sides of brx and car must be in line, facing the front side. Left (y axis): left side of brx must be...

  • Page 18

    18 main menu display this menu is to check what is the default display layout to change the default live display, please use dvr viewer. Press [esc] button for returning to the previous mode. Recording conditions such as frame rate, resolution and image quality can be checked. To change the record s...

  • Page 19

    19 main menu to change the resolution, quality, pre-recording time, post-recording time, please use dvr viewer. Change the channel and check the record set up per channel to change the record normal/event, fps, audio on/off, please use dvr viewer. Disk end mode (overwrite) on/off to change the disk ...

  • Page 20

    20 main menu system date/time/language and ntsc/pal can be configured in this menu. Press [esc] button for returning to the previous mode. Date/time/language system time, date format, time format, time zone, dst, gps time synchronize can be configured in this menu..

  • Page 21

    21 main menu permission management dvr id, user id can be checked. To change the dvr id, user id, please use dvr viewer. Date/time/language hdd format time differs from the capacity of ssd/hdd. Be carefully noted that hdd format deletes all the current data. Power cut-off during hdd format or upgade...

  • Page 22

    22 configuration configuration upload to dvr configuration download from dvr the configuration file can be saved into a usb memory stick via dvr viewer software. Insert usb memory stick containing configuration file (set operation condition) to usb port in brx. It may take around 5~10 seconds till u...

  • Page 23

    23 brx200a dvr viewer guide [pc system requirement] if the pc does not meet the minimum system requirement, the dvr viewer may not function properly. Os windows xp, windows vista, windows 7 cpu intel core 2 duo (2ghz)or higher ram 1gb or higher vga memory 256mb or higher hdd free space install 120mb...

  • Page 24

    24 installing procedures 1. Insert the cd into your pc and run [setup.Exe]. 3. Continuously install ext2fsd driver. It’s necessary to read the removable hdd/ssd. 2. Select the language and then follow the dialog box. Dvr viewer software is on the provided cd. 4. Click finish to allow the system to r...

  • Page 25

    25 the “dvr viewer” icon will be displayed on your desktop. Run dvr viewer. Note: to un-install the “dvr viewer brx2004a” open the “control panel” select [remove program] and remove [dvr viewer brx2004a] run & dvr viewer setting to set the dvr viewer itself, click setting. Setting this setting is fo...

  • Page 26

    26 dvr configuration setting to set the dvr configuration, firstly, connect a usb memory stick into your pc’s usb slot. And run “dvr viewer brx2000a” and click setting. Setting and then click machine config [new] if you already have a dvr configuration in your memory stick, click [open]. Select “set...

  • Page 27

    27 dvr configuration setting device camera cam title the camera title can be up to 10 characters. Brightness adjust brightness of camera contrast adjust contrast of camera display default layout select default display layout. If you set 2x2, when you turn on the dvr quad screen will be on the screen...

  • Page 28

    28 dvr configuration setting g-sensor calibration if you install front (x axis): front sides of brx and car must be in line, facing the front side. Left (y axis): left side of brx must be facing the left side of car and brx must be horizontal, parallel with the ground. Top (z axis): top of brx must ...

  • Page 29

    29 different installation 3 - brx front is facing left side of the car. Different installation 2 - brx top is facing the ground. Dvr configuration setting different installation 4 - brx bottom is facing left side of the car . (x:180, y:0, z:0) (x:180, y:0, z:180) (x:180, y:0, z:270) (x:180, y:0, z:9...

  • Page 30

    30 dvr configuration setting set g-sensor trigger level [1(insensitive)~5(the most sensitive)] if g-sensor sensitivity value is high (5), it may be too sensitive, it will detect even a light impact or light turn. If g-sensor sensitivity value is a low setting (1), it might not detect a notable incid...

  • Page 31

    31 dvr configuration setting record video type select your video standard(camera type.). This video standard(ntsc/pal) is just for fps calculation. This is different from your dvr video standard. To change your dvr video standard, set you r video standard at service menu of dvr. Refer to page 21. Au...

  • Page 32

    32 dvr configuration setting remained fps show remained fps / total fps resolution d1: 720x480(ntsc), 720x576(pal) hd1: 720x240(ntsc), 720x288(pal) cif: 360x240 (ntsc), 360x288(pal) quality normal: small file size, low picture quality. High: super: large file size, good picture quality. Event r ecor...

  • Page 33

    33 dvr configuration setting event motion detection to use motion detection as a event, check the camera first. Sensitivity 1(insensitive)~5(the most sensitive) set grid default setting: all area is motion detecting area. To disable motion detect, click blocks and make it to black. Record ch select ...

  • Page 34

    34 alarm input dvr configuration setting to use alarm in as a event, check the alarm first. Title set alarm in title type set alarm in type alarm in 1~4: voltage on / voltage off. Alarm in 5~8: normal close / normal open record ch select alarm record channel alarm out1 set alarm out 1 duration from ...

  • Page 35

    35 signal dvr configuration setting title set signal title record ch select signal record channel alarm out1 set alarm out 1 duration from 0~ alarm out2 set alarm out 2 duration from 0~ live out set live display channel live out duration set live display duration. Live display channel will automatic...

  • Page 36

    36 g-sensor / speed dvr configuration setting gps speed set gps speed, over this speed will trigger. Pulse speed set car speed pulse speed, over this speed will trigger. . Record ch select speed triggered record channel alarm out1 set alarm out 1 duration from 0~ alarm out2 set alarm out 2 duration ...

  • Page 37

    37 live out priority dvr configuration setting this menu is to set the default live display priority. 1 is the most priority display channel on the live screen. 2x2_1 : quad mode (cam1~cam4) 2x2_2 : quad mode (cam5~cam8) 3x3 : 8 split mode (cam1~cam8) if you set 2x2_1 as 1 and turn on the dvr, the f...

  • Page 38

    38 dvr configuration setting system language set your dvr language date format set your dvr date format. Time format set your dvr time format speed format set your dvr speed format apply dst set daylight saving time time zone set your time zone time sync (gps) set time synchronize time. Boot on or e...

  • Page 39

    39 connect removable hdd/ssd 1. Connect removable ssd/hdd to your pc through provided usb mini cable. 2. Run “dvr viewer brx2000a” 3. Click [hdd load] icon. [hdd load] icon 4. Select hdd [note] up to 4 removable hdd/ssd can be connected to a pc at the same time. 5. Then calendar search screen will b...

  • Page 40

    40 open data folder use this button after you download the whole removable hdd data into a folder in your pc. If you copied all removable hdd files include folders into the [aaa] folder as below, click open data folder button and then select [aaa] folder to open the data. Select [aaa] folder and the...

  • Page 41

    41 playback screen playback control buttons slide bar camera title (resolution) date/time speed pulse speed/signal/google map/alarm in 1-8 playback can be controlled with the buttons in bottom left and slide bar helps easy movement to the required playback position or time. In case that the user wan...

  • Page 42

    42 main buttons / playback control buttons before reverse pause play next audio on/off volume control playback speed control (x1, x0.5, x2, x, x8, x16, x32 converting the captured file to jpeg format. Recording the file which is currently played back in the software. Main buttons playback control bu...

  • Page 43

    43 select display layout click [select layout] button and then window for layout selection appears. [select layout] button window for layout selection click this icon for returning to the previous screen. [select layout] button to see 1 camera only, double click screen. Or right-click on screen and ...

  • Page 44

    44 view information click [view information] button during playback. [view information] button check the box to see the information like g-sensor graph, speed graph etc. The data of g-sensor (x : red, y : green, z : blue) & speed (grey) are displayed as graphs and alarms & car signals are displayed ...

  • Page 45

    45 google map click [google map] button during playback. [google map] button now here to see the route & position on the google map, the gps data should be recorded with video. To see the map, the pc must be connected to the internet. The playback position will be shown on the map with an arrow. The...

  • Page 46

    46 multi windows main dvr viewer, information window and google map window can be displayed at the same monitor together and their size can be adjusted as per the application. 3 different windows can work as an integrated analysis software, which improves the efficiency of the security/fleet managem...

  • Page 47

    47 calendar search click [calendar search] button during playback to search the other date. [calendar search] button dates containing recorded data are to be marked with box of orange color. Once the selected date is clicked, the hours containing recorded data are marke d with orange color, too. Cli...

  • Page 48

    48 event search click [event search] button to search event quickly. [calendar search] button [event search] brx can access to the data of g-sensor trigger, car signal information, alarm or speed with video/audio, which means that user can easily search and playback the classified data by the differ...

  • Page 49

    49 privacy set click [privacy set] button to set privacy region. [privacy set] button brx can set up the privacy region at each channel to protect the people/informat ion from unnecessary disclosure to public. The set privacy region becomes invisible in case of back up the original data to j pg, avi...

  • Page 50

    50 save jpg / save avi pause the playback and click [save jpg] button to make a jpg file. [save jpg] button pause the playback and click [save avi] button to make a avi file. [save avi] button.

  • Page 51

    51 print image pause the playback and click [print image] button to print out. [print image] button type in the title [print title] & any comments [comment] using the keyboard..

  • Page 52

    52 backup click [backup] button to backup the files to the pc. [backup] button type in the memo title & memo using the keyboard. And then set the type (folder name) and click start button. Type means a folder name. Need this to start backup..

  • Page 53

    53 backup list search click [backup list] button to playback backup file. [backup list] button select type to search. Under selected type, file list shows up with the information of time, dvr id, user id. Select the required file and click [ok] button..

  • Page 54

    54 about click [about] button to check the product information. [about] button click [hotkey] tap to check the hot key (simplified button) for the functions of dv r viewer software..

  • Page 55

    55 specifications.

  • Page 56

    Rsg engineering limited 19 hollies business park, hollies park road, cannock, staffordshire ws11 1db. Telephone: 01543 438800 fax: 01543 438801 email: sales@rsg-ontop.Com web: www.Rsg-ontop.Com.