- DL manuals
- Dacor
- Ranges
- Epicure ER36D
- Technical Manual
Dacor Epicure ER36D Technical Manual
Summary of Epicure ER36D
Page 1
Dacor technical service: 800-353-2267 dacor 1140 bridge gate drive diamond bar, ca 91765 800-793-0093 technical manual range models: er30d, er36d, er48d.
Page 2: 7 - T
Page 7-1 s ection 7 - t roubleshooting g uide section 7 - troubleshooting guide control panel error codes the error codes below apply to both models er36d and er48d. General error codes the following codes give a general indication of the location of problems detected by the control panel controller...
Page 3
Page 7-2 d acor r ange s ervice m anual basic troubleshooting instructions if the range does not function properly, check for obvious problems first, such as the main power switch being turned off, or the control panel being locked. If the problem is not immediately obvious, use the performance test...
Page 4: 7 - T
Page 7-3 s ection 7 - t roubleshooting g uide troubleshooting chart - oven (continued) problem possible causes what to check time on display not correct. Time of day not set. Set time. • power failure or power was turned off. Reset time. • control panel problems. Oven controller board. • time flashe...
Page 5
Page 7-4 d acor r ange s ervice m anual troubleshooting chart - oven (continued) problem possible causes what to check foods over or under cook. Incorrect cooking time or temperature. Follow instructions in operating instructions section. • items not being cooked on rack level that will provide best...
Page 6: 7 - T
Page 7-5 s ection 7 - t roubleshooting g uide troubleshooting chart - cooktop problem possible causes what to check igniters do not spark. Control panel is dark. Range not connected to electrical power. Have electrician connect range to properly wired electrical connection. • power to range is off. ...
Page 7
Page 7-6 d acor r ange s ervice m anual troubleshooting chart - cooktop problem possible causes what to check igniter continues to spark (click) after flame ignites. Burner is cold. Burners may continue to spark for up to 60 seconds when cold and set to low. See operating the cooktop section for mor...
Page 8: 8 - R
Page 8-1 s ection 8 - r ange d isassembly section 8 - range disassembly open the oven door completely. Pull the hinge locks forward on both hinges, until they stop. • • danger turn off electrical power at the main power supply and the gas supply at the gas supply valve before servicing the range. Fa...
Page 9
Page 8-2 d acor r ange s ervice m anual grasp the oven door on opposite sides and hold it at a 15° angle from the front of the oven. Slide the hinges a into the hinge openings b , resting the bottom of the hinge arms c on the lower lip d of the hinge receptacles. Continue to hold the door at a 15° a...
Page 10: 8 - R
Page 8-3 s ection 8 - r ange d isassembly removing the back panel turn off the gas supply at the gas supply valve and power to the range at the junction or fuse box. Pull the range out from the wall or cabinet. Remove the grates, the burner caps, burner rings, and crown burner heads from the cooktop...
Page 11
Page 8-4 d acor r ange s ervice m anual pull the island trim/backguard j up and off the range. Remove the stainless steel spill tray trim piece l . • • remove the electrical access panel cover n by removing the two (2) screws m that hold it in place. Remove the two (2) screws o on the sides of the e...
Page 12: 8 - R
Page 8-5 s ection 8 - r ange d isassembly remove the end cap. • removing the side panel(s) loosen the end cap set screws b through the access holes c on the bottom of the front panel lip d . • d b c turn off the gas supply at the supply valve and power to the range at the junction or fuse box. Pull ...
Page 13
Page 8-6 d acor r ange s ervice m anual remove the grates, the burner caps, burner rings, and crown burner heads from the cooktop. Remove the screws above the spill tray that hold the side panel in place. • • lift the side panel off of the range. • remove the side panel screw inside the front panel ...
Page 14: 8 - R
Page 8-7 s ection 8 - r ange d isassembly h i removing the spill trays turn off the gas supply at the supply valve and power to the range at the junction or fuse box. Remove the grates, the burner caps, burner rings, and crown burner heads from the cooktop. Remove the spill tray trim screws, located...
Page 15
Page 8-8 d acor r ange s ervice m anual remove the screws from the stack burner heads h (eight [8] screws total). • remove each of the stack burner heads. When removing the head, disconnect the igniter wire from each one. • gently lift up on the back of one of the porcelain trim pieces i where the s...
Page 16: 9 - C
Page 9-1 s ection 9 - c omponent r epair section 9 - component repair door gasket (seal) remove the oven door. See the door removal section on page 8-1. Lay the door on a flat, padded surface with the door gasket a facing up. Remove the gasket by grasping sections of it and pulling up. Insert the se...
Page 17
Page 9-2 d acor r ange s ervice m anual door handle (er36d) remove the oven door. See the door removal section on page 8-1. Lay the door on a flat, padded surface with the door gasket facing up. Remove the two (2) door handle screw plugs x . The door handle mounting screws are located below the plug...
Page 18: 9 - C
Page 9-3 s ection 9 - c omponent r epair front door glass assembly front door glass assembly remove the oven door. See the door removal section on page 8-1. Lay the door, handle down, on a flat, padded surface with the door gasket facing up. Remove the two (2) screws b in the top corners of the door...
Page 19
Page 9-4 d acor r ange r r s ervice m anual when putting the front door glass assembly back in place, be careful not to knock loose the door spacers which are glued to the top corners. Also, make sure the tabs e on the bottom rest on the outside of the door liner. Reinstall the screws on the bottom ...
Page 20: 9 - C
Page 9-5 s ection 9 - c omponent r epair door hinges (continued) grab the front door glass assembly with both hands and remove it. • remove the two (2) hinge cover screws f over the hinge to be removed and pull off the hinge cover g . Remove the hinge retainer screw h for the hinge to be removed. • ...
Page 21
Page 9-6 d acor r ange s ervice m anual door component repair (continued) inner window assembly remove the oven door. See the door removal section on page 8-1. Lay the door, handle down, on a flat, padded surface with the door gasket facing up. Remove the two (2) screws b in the top corners of the d...
Page 22: 9 - C
Page 9-7 s ection 9 - c omponent r epair inner window assembly (continued) remove the four (4) screws j that hold the outer heat shield k in place. Lift the outer heat shield out. • remove the four (4) screws l that hold the lower outer heat shield m in place. Lift the lower heat shield out. • remov...
Page 23
Page 9-8 d acor r ange s ervice m anual if the inner widow gasket p must be removed, make sure it is fit completely into the groove around the window opening before replacing the window assembly. Replace the window glass assembly. The seam in the metal rim around the inside of the glass must be plac...
Page 24: 9 - C
Page 9-9 s ection 9 - c omponent r epair cooktop component repair general to make repairs to the cooktop gas supply lines (flex tubes), remove the spill trays. See page 8-7 for instructions. Each burner is fed by two (2) flex tubes from the valve. The larger flex tube is the main gas supply line. It...
Page 25
Page 9-10 d acor r ange s ervice m anual c e f f d cooktop component repair (continued) regulator turn off the gas supply at the supply valve and power to the range at the junction or fuse box. Pull the range out from the wall or cabinet. Remove the gas regulator access cover a from the back of the ...
Page 26: 9 - C
Page 9-11 s ection 9 - c omponent r epair igniters and orifices (injectors) replacement of the crown burner igniters or orifices require the removal of the spill trays. The spill trays do not need to be removed to replace the stack burner igniters or orifices. Stack burner turn off the gas supply at...
Page 27
Page 9-12 d acor r ange s ervice m anual stack burner orifice replacement use a 7 mm hex driver or socket to remove the orifice from the burner base. The main orifice m is located in the center of the burner. The simmer orifice n is located near the outside of the base. Consult the dacor technical s...
Page 28: 9 - C
Page 9-13 s ection 9 - c omponent r epair crown burner orifice replacement (continued) the simmer orifice is attached to a fitting on the side of the crown burner. Remove the fitting retaining clip t to access the simmer orifice fitting. Pull the fitting u out of the side of the burner. Use a 7 mm h...
Page 29
Page 9-14 d acor r ange s ervice m anual cooktop component repair (continued) knob lights (led assembly) turn off the gas supply and power to the range at the junction or fuse box. Remove the spill trays. See the removing the spill trays section on page 8-7. Pull off the knob in front of the led ass...
Page 30: 9 - C
Page 9-15 s ection 9 - c omponent r epair manifolds and valves turn off the gas supply and power to the range at the junction or fuse box. Remove the spill trays. See the removing the spill trays section on page 8-7. Remove the torx head screws from the end caps f through the access holes g on the b...
Page 31
Page 9-16 d acor r ange s ervice m anual make sure the oven control panel i is in the lowered position. See page 5-2. Pull the bottom of the front panel j out and lift it up and off the range. • • remove all of the screws that hold the channel support k to the cooktop chassis. Lift the channel suppo...
Page 32: 9 - C
Page 9-17 s ection 9 - c omponent r epair manifolds and valves (continued) to remove the valves p , remove the bolts q from the bottom of the manifold r . After repairs are completed, reassemble the cooktop and test it to make sure repairs were properly completed. • • r q p oven component repair smo...
Page 33
Page 9-18 d acor r ange s ervice m anual oven component repair (continued) the oven chamber smoke eliminator d is located on the ceiling of the oven chamber near the back. Exact location varies with model. Remove the three (3) screws that hold the smoke eliminator in place. Be careful not to scratch...
Page 34: 9 - C
Page 9-19 s ection 9 - c omponent r epair convection element, fan and fan motor turn off the gas supply and power to the range at the junction or fuse box. Remove the oven racks from the oven. Remove the oven door(s) as described on page 8-1. Remove the convection filter from the back wall of the ov...
Page 35
Page 9-20 d acor r ange s ervice m anual convection fan and fan motor removal to remove the convection fan u , hold it with one hand and turn the nut v clockwise with a wrench. With the back cover removed (see page 8-3), label the location of the convection fan wires w and disconnect them. Remove th...
Page 36: 9 - C
Page 9-21 s ection 9 - c omponent r epair broil element left oven on model er48d: turn off the gas supply at the supply valve and power to the range at the junction or fuse box. Remove the oven door as described on page 8-1. Remove the oven racks. Remove the convection filter e from the back wall of...
Page 37
Page 9-22 d acor r ange s ervice m anual label the wires g that connect to the broil element terminal. Gently remove the broil element wires from the terminal block h on the broil element assembly. • • place the broil element assembly on a flat, padded surface and remove the screws from each of the ...
Page 38: 9 - C
Page 9-23 s ection 9 - c omponent r epair broil element (continued) place the broil element into the oven chamber with the glass facing down and the terminals toward the back of the oven. Lift the back of the element up and reconnect the broil element wires to the terminals on the broil element asse...
Page 39
Page 9-24 d acor r ange s ervice m anual oven component repair (continued) broil element for right oven on model er48d and oven on model er36d: turn off the gas supply at the supply valve and power to the range at the junction or fuse box. Remove the oven door as described on page 8-1. Remove the ov...
Page 40: 9 - C
Page 9-25 s ection 9 - c omponent r epair temperature sensor and rack support the following applies to all er36d and er48d ovens, including the left oven on model er48d: turn off the gas supply at the supply valve and power to the range at the junction or fuse box. Remove the oven door as described ...
Page 41
Page 9-26 d acor r ange s ervice m anual reinstalling the rack support: insert one end of the rack support into the oven at a 20° angle to the sidewall. Rotate the rack support into place, matching the four (4) protruding pins on the rack support to the holes in the oven wall. Mount the rack support...
Page 42: 9 - C
Page 9-27 s ection 9 - c omponent r epair light fixtures and meat probe (continued) remove all the mounting screws from the intake grill k . The screws attach the grill to the underside of the cooktop front panel i and the top of the oven chambers(s) j . Remove the intake grill. • • meat probe conne...
Page 43
Page 9-28 d acor r ange s ervice m anual light fixture removal trace the light fixture wire up into the space m above the oven chamber. Find the connector on the wire inside, and disconnect it. • oven component repair (continued) caution use the lens pry stick with caution. Do not cause uneven stres...
Page 44: 9 - C
Page 9-29 s ection 9 - c omponent r epair light fixtures and meat probe (continued) reinstalling the rack support: insert one end of the rack support into the oven at a 20° angle to the sidewall. Rotate the rack support into place, matching the four (4) protruding pins on the rack support to the hol...
Page 45
Page 9-30 d acor r ange s ervice m anual oven component repair (continued) cooling fan assembly repair turn off the gas supply at the supply valve and power to the range at the junction or fuse box. Move the range out from the wall or cabinet and remove the back panel as described on page 8-3. The c...
Page 46: 9 - C
Page 9-31 s ection 9 - c omponent r epair turn off the gas supply at the supply valve and power to the range at the junction or fuse box. Remove the spill trays as described starting on page 8-7. Remove the relay board cover g on the floor of the cooktop chassis. • • • oven component repair (continu...
Page 47
Page 9-32 d acor r ange s ervice m anual control panel repair follow these instructions to access the controller board, keypad membrane and mounting hardware. Turn off the gas supply at the supply valve and power to the range at the junction or fuse box. Remove the spill trays as described starting ...
Page 48: 9 - C
Page 9-33 s ection 9 - c omponent r epair e f control panel repair (continued) remove the screws from the bottom of the cooktop front panel d . • make sure the oven control panel e is in the lowered position. See page 5-2. Pull the bottom of the front panel f out and lift it up and off the range. • ...
Page 49
Page 9-34 d acor r ange s ervice m anual to remove the control panel assembly h for service, remove the nuts that hold the assembly to the sub panel i . Label and disconnect any wires that are disconnected from the controller board or keypad membrane before repair or replacement. Reassemble the rang...