DL manuals
Dacor
Blower
ILb10
Instructions Manual

Dacor ILb10 Instructions Manual

Other manuals for ILb10: Planning Manual

Page of 8

Download

Print this page

Bookmark us

IMPORTANT

1. Before beginning installation, please thoroughly read and become familiar with these instructions.

2. Installation and service must be completed by a qualified installer or service agency.

3. Installer: Please leave these Installation Instructions with the owner.

4. Owner: Please keep these instructions for local electrical inspector’s use and for future reference.

5. Read the accompanying Use & Care Manual prior to operating this appliance.

TABLE OF STEPS

Installation Planning

Pages 2-3

Electrical Connection

Pages 3-5

Installing the ILB

Page 6

Installing the REMP

Page 6

Verifying Proper Operation

Page 6

Part No. 65265 Rev. D

TESTED IN ACCORDANCE WITH THE LATEST EDITION OF ANSI/UL507, STANDARD FOR ELECTRIC FANS, AND

CSA C22.2 NO. 113, STANDARD FOR FANS AND VENTILATORS.

NOTES:

Contain helpful hints and tips to facilitate the installation.

CONVENTIONS USED IN THESE INSTRUCTIONS

WARNINGS:

Must be followed carefully to avoid personal injury or damage.

READ AND SAVE THESE INSTRUCTIONS

Installation Instructions

Remote Blowers

1 2 3 4 5 6 7 Next › »

Summary of ILb10

Page 1
Important 1. Before beginning installation, please thoroughly read and become familiar with these instructions. 2. Installation and service must be completed by a qualified installer or service agency. 3. Installer: please leave these installation instructions with the owner. 4. Owner: please keep t...
Page 2
1 warning: to reduce the risk of fire, electric shock, or injury to persons, observe the following: a) installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction. B) sufficient air is needed for...
Page 3
2 installation planning a qualified technician must complete the installation of this appliance. Carefully check the location where the remote blower is to be installed. The remote blower should be placed for convenient access. Make certain that electrical power can be provided in the selected locat...
Page 4
3 note: the ilb8 & ilb10 inline blowers are only approved in updraft (hood) applications. Note: the remp must be sealed between the roof or wall and the underside of the flange with mastic to prevent leaks. For installation on a flat roof, or a roof with a pitch of less than 2:12, install the remp o...
Page 5
4 n1 l1 n2 blk wht 120vac, 60hz, 15a supply power from dedicated circuit breaker grn wht l2 blk blk wht gnd grn gnd grn rv l2 n2 gnd grn wht blk cabp3 l2 n2 gnd grn wht blk remp j-box wiring of rv with remp and cabp3 n1 l1 n2 l2 n2 gnd blk wht 120vac, 60hz, 15a supply power from dedicated circuit br...
Page 6
5 l1 n1 gnd l2 n2 gnd l2 n2 gnd grn wht blk l2 n2 gnd grn wht 120vac, 60hz, 15a supply power from dedicated circuit breaker blk grn wht blk grn wht blk grn wht blk ilb remp j-box remote blower/ hood wiring of dacor remote blower/hood with ilb and remp l1 n1 gnd l2 n2 gnd l2 n2 gnd grn wht 120vac, 60...
Page 7
6 installing the ilb mount the ilb using the 4 screws, isolation grommets and washers provided in the parts bag, included in the instruction envelope. Installing the remp mount the remp to the wall or roof using screws, through mounting trim flange. Verifying proper operation 1. Temporarily re-insta...
Page 8
Web site: www.Dacor.Com for a dealer/service: (800) 772-7778 corporate phone: (800) 793-0093.