1. DL manuals
  2. Daewoo
  3. Monitor
  4. DPP-42A2(GDBD)
  5. User Manual

Daewoo DPP-42A2(GDBD) User Manual

Summary of DPP-42A2(GDBD)

  • Page 1

    Plasma display user’s manual dpp-42a2(gdbd) dpp-42a2(gjbd) d p p - 4 2 a 2 ( g m b ) dpp-42a2(gmbd) dpp-42a2(gwbd) dpp-42a2(ldbd) d p p - 4 2 a 2 ( l m b ) dpp-42a2(lmbd) d p p - 4 2 a 2 ( l j b d ) dpp-42a2(lwbd) proper use guarantees product life. Before using the product, be advised that you read...

  • Page 2: F E A T U R E S

    This owner’s manual presents safety precautions and how to use the product. After reading it thoroughly, use the product safely. Keep this manual where the user can see it easily. Failure to comply with warnings and cautions for the safe use of electric appliances may cause fire or human injury. • 4...

  • Page 3: Safety Precautions

    Always obey all safety messages. • all the safety and operating instructions should be read before the product is operated. If anything strange happens, unplug this product from the wall outlet. • do not disassemble or replace any parts of the tv. Refer to a qualified service personnel for repair. S...

  • Page 4

    5 during use do not open the cover (or back) because high voltage is present within the tv enclosure. It may cause electric shock. Never push any kind of objects into this product through openings at the back of tv. It may cause fire or electric shock. The apparatus shall not be exposed to dripping ...

  • Page 5: Safety Precautions

    Always obey all safety messages. • all the safety and operating instructions should be read before the product is operated. Safety precautions 6 power installation caution you can be injured, or this product or any other of your property can be damaged if you don’t follow instructions. When moving y...

  • Page 6

    7 7 during use do not wipe the tv using a cloth damped with chemicals (benzene, thinners, etc.). The tv appearance may be marred. (unplug the power plug and wipe with soft cloth.) do not place any object or cover on the tv. In an event of improper ventilation, the tv will be overheated causing fire....

  • Page 7: Checking Accessories

    8 checking accessories note the following items are optional accessories. Refer purchasing optional accessories from daewoo electronics local retailers or the retailer from where you purchased the unit. Optional accessories wall mounting unit stand unit remote control 1 unit note check to be sure th...

  • Page 8

    9 how to install cable holder 1 2 3 the method of wire arrangement 1 assemble the cable holder enclosed on the back of tv. (picture 1) (assembly method: after you push the "a"(prominence part of cable holder) in the hole, rotate the cable holder clockwise as an angle of 90°. You can separate in reve...

  • Page 9

    10 how to use scart to rca jack scart to rca jack is provided with the specific models for changing scart signal to rca signal or rca signal to scart signal. Scart to rca jack has a 'input / output' selecting switch. While scart to rca jack is connected to av1, you can select 'input' or 'output' wit...

  • Page 10: Contents

    11 4 • safety precautions 8 • checking accessories 12 • panel controls 14 • remote control preparation connection 16 • antenna connection 18 • to watch tv 20 • install program 26 • watching digital broadcasts 28 • watching cable broadcasts 30 • watching satellite broadcasts 32 • watching a dvd image...

  • Page 11: Panel Controls

    12 panel controls front panel, rear panel * items having the same name on the plasma display and the remote control would function in exactly the same way. Front / side menu pr control sensor power standby: red - standby blue - on stand-by/operate on/off select when adjusting volume or select/adjust...

  • Page 12

    13 rear ant service optical digital audio input pc audio pc hdmi component av1 av2 pc input (15 pin d-sub) hdmi input component a/v jacks scart, a/v input/output. Pc audio input ant.

  • Page 13: Remote Control

    14 remote control note • use two “aaa” batteries. • be sure to use replacement batteries of the same type as the original ones. • the life of a battery depends on how much it has been used. * the number in ( ) indicates the page in which the function of each button is explained in detail. Use to sel...

  • Page 14

    15 when using remote control: • be sure not to allow the remote control to drop or to become wet. • keep it away from hot or moist locations. Installing the batteries in your remote control: • push to open the cover of the remote control • put the batteries in the battery cell after checking the pol...

  • Page 15: Ctv Antenna Connection

    16 ctv antenna connection tv antenna installation may be found in most. When a coaxial cable is used plug the coaxial cable to the antenna socket, and fix it firmly. When a feeder cable is used ant/cable ant/cable coaxial cable antenna connection.

  • Page 16: Outdoor Antenna Connection

    17 outdoor antenna connection-such as vhf or/and uhf-may be necessary for installation at private houses single antenna connection. Separate antenna connection. Vhf antenna uhf antenna ant/cable ant/cable outdoor antenna connection vhf-antenna uhf-antenna in case of coaxial cable in case of feeder c...

  • Page 17: To Watch Tv

    18 to watch tv - the buttons on the keypad in the pdp unit, which have the same name as those on the remote control, perform the same function as the remote control. Press the “power” button of the pdp unit. •the “ + pr - ” or power button of the remote control and the keypad on the pdp unit would b...

  • Page 18

    19 press the “power” button. • connect the ac power cord to pdp unit. • the led of the pdp unit turns red colour when power cord connect ac power. • press the “ + pr - ” or “power” button of the remote control or keypad of the pdp unit. • the led of the pdp unit turns “blue” colour and the tv turns ...

  • Page 19: Install Program

    20 install program - this is the function for the tv to memorize the broadcasting channels. If the auto setup is done, you can simply find programs with “ + pr - ” buttons and so need not select programs by pressing each program number. - up to 100 tv stations can be stored in this set by programme ...

  • Page 20

    21 select the “auto setup”. • select the “auto setup” with the “ ▼▲ ” button. • then press the “ ◀▶ ” button. Select the “country”. • there are 20 countries for selection. Choose the desired country before starting the search. • if there is no proper country, select the "others". Select the “search”...

  • Page 21: Edit

    22 edit deleting the program. • place the selection bar on the program that you want to delete using the “ ▼▲ ” and “ ◀▶ ” buttons. • press the delete(yellow) button. • the deleted program goes to pr number 99 for recover. Moving the program positions • place the selection bar on the program that yo...

  • Page 22: Manual Setup

    23 press the number buttons(0~9) or the “ ◀ ◀▶ ▶ ” button to select a program number you want. Find the desired channel. • using “ ◀▶ ” button or number keys, select the desired channel directly, if you know it otherwise step through the numbers using the ▶ button until you find the right channel. •...

  • Page 23: Manual Setup

    24 manual setup name the program • using “ ◀▶ ” button, move the position where you want to write the character. • select the desired character with the “pr” button. • there are a-z, +, ., /, and 0-9 characters. • after naming, it will be save when you select “ok” in memory. You can exit by pressing...

  • Page 24

    25 memorize the program. Move select menu exit manual setup program channel fine tune name video audio search memory 01 c06 c06 pal d/k 0 picture screen sound feature install 7 • without memorizing, the program will not be saved. • press “ ◀▶ ” buttons to memorize the program after selecting ‘memory...

  • Page 25: Watching Digital Broadcasts

    26 watching digital broadcasts • to watch digital broadcasts: - purchase a separate digital broadcasting receiver(set-top box) - connect the pdp to a digital broadcasting receiver as shown right. Watching digital broadcasts press the power buttons • turn the pdp and the receiver on. 2 connect a digi...

  • Page 26

    27 input select • select [component] by pressing the "multimedia" button of the remote control or using the “input select” button of the pdp unit. • each time you press the “multimedia” button, different input modes appear. The sequence is as follows: select the desired channel and function • select...

  • Page 27: Watching Cable Broadcasts

    28 watching cable broadcasts • to watch cable broadcasts, subscribe to your local cable tv broadcasting, and then connect a cable broadcasting receiver to the pdp as shown right. Watching cable broadcasts press the power buttons • turn the pdp and the receiver on. 2 connect a cable broadcasting rece...

  • Page 28

    29 input select • select [av 1(scart), av 2(scart) or av3(s-video)] by pressing the [av] button of the remote control or the "input select" in keypad of the pdp unit. • each time you press the [av] button, different input modes appear. The sequence is as follows: select the desired program and funct...

  • Page 29

    30 watching satellite broadcasts • to watch satellite broadcasting, subscribe to digital satellite broadcasting, then connect the satellite broadcasting receiver to the pdp as shown right. Watching satellite broadcasts press the power buttons • turn the pdp and the satellite receiver on. 2 connect a...

  • Page 30

    31 input select select the desired program and function • select the desired program and function by using the remote control of the satellite broadcasting receiver. 3 4 av1 av2 av(s)3 • select [av 1(scart), av 2(scart) or av3(s-video)] by pressing the [av] button of the remote control or the "input...

  • Page 31: Watching A Dvd Image

    32 ant service optical digital audio input pc audio pc hdmi component av1 av2 watching a dvd image • component input is set to 480i/576i and 480p/576p mode. • connect the cable from the dvd video output (y, pb/cb, pr/cr) to the component input at the back of pdp, and connect the cable from dvd audio...

  • Page 32

    33 input select • select [component, av1(scart), av2(scart) or av3(s-video)] by pressing the [multimedia] or [av] button of the remote control or the "input select" in keypad of the pdp unit. • each time you press the [multimedia] or [av] button, a different input mode appears. The sequence is as fo...

  • Page 33: Watching A Vcr Image

    34 watching a vcr image • video can use either the video terminal or the s-video terminal. Watching a vcr image press the power buttons • turn the pdp and the vcr on. 2 connect a vcr to the pdp. • prepare the av cable. • connect the video(output) to pdp(video input) as shown below. 1 s-video vcr vid...

  • Page 34

    35 input select select the desired title and function • select the desired title and function by using the remote control of the vcr. 3 4 notes: 1) when connecting a vcr, the s-video terminal provides a better image than the video terminal. 2) when connecting to the video terminal, connect 3 colour ...

  • Page 35

    36 watching a camcorder/game console image • enjoy images recorded by camcorder or the game console after connecting to the pdp. Watching a camcorder/game console image press the power buttons • turn the pdp and the camcorder/game console on. 2 connect a camcorder/game console to the pdp. • prepare ...

  • Page 36

    37 input select select function • select the function by using the remote control of camcorder or game console. 3 4 notes: 1) when connecting the device, the s-video terminal provides a better image than the video terminal. 2) when connecting to the video terminal, connect 3 colour av cables (video,...

  • Page 37: Connecting Pc(15Pin D-Sub)

    38 ant service optical digital audio input pc audio pc hdmi component av1 av2 connecting pc • this product supports resolutions of vga, svga, xga, sxga, uxga. • before connecting a pc to the pdp, be sure to adjust the resolution of the pc. Connecting pc(15pin d-sub) connect the pc to the pdp. • prep...

  • Page 38

    39 input select • select [pc] by pressing the [mulimedia] button of the remote control or pdp unit. • each time you press the [mulimedia] button, a different input mode appears. The sequence is as follows: • n.B. : you cannot select pc if the picture in picture mode is on. Enjoy dynamic ultra screen...

  • Page 39: Connecting Hdmi

    40 connecting hdmi • this product supports resolution of vga, svga, xga, sxga, uxga. • before connecting a pc to the pdp, be sure to adjust the resolution of pc. • this product is supported by plug and play only at hdmi. • this plasma unit is compliant with hdmi 1.1 version. Connecting hdmi connect ...

  • Page 40

    41 input select • select [hdmi] by pressing the [multimedia] button of the remote control or the input button on the pdp unit. • each time you press the [multimedia] button, a different input mode appears. The sequence is as follows: 3 press the power buttons. • turn on the pdp and dvd or game conso...

  • Page 41

    42 connect with the dolby digital amp. Surround l surround r r l center woofer dolby digital amp i n p u t optical output if you connect the optical output to a dolby digital amp, you can listen to better sound..

  • Page 42

    43 pc and hdmi input resolution available in pdp • depending on graphic card, problems like no signal detected or line noises can happen. If these problems happen, contact the graphic card company for help. Resolution h freq. (khz) v freq. (hz) remark hdmi pc 31.469 37.861 37.500 31.469 35.156 37.87...

  • Page 43: Selecting Picture Mode

    Selecting picture mode selecting picture mode • press the [p.Mode] on the remote control. • while pressing the [p.Mode] for the first time, the current picture mode will be displayed. Each press of the button will select one of four picture modes. • each time you press the button, a different pictur...

  • Page 44: Customising Picture

    45 customising picture • you can adjust the colour tone and brightness to your preference. Press the button. • after selecting [picture] by the “ ” buttons, press the “ ” button. Then the sub menu of [picture] will be displayed. Select the user mode. • select [user] by the “ ” buttons in the [mode]....

  • Page 45

    46 select user mode adjustments picture condition adjustments • press the “ ” buttons to adjust the picture of your preference. • n.R. Functions the noise reduction. 4 5 move adjust menu exit normal on 50 50 8 50 mode brightness contrast sharpness colour colour temp. N.R. User picture screen sound f...

  • Page 46

    47 press the “colour temp” button on the remote control. 6 move adjust menu exit 50 50 8 user normal on 50 mode brightness contrast sharpness colour colour temp. N.R. Picture screen sound feature install • pressing the “colour temp” button first time will display the current setting for colour temp....

  • Page 47: Adjusting Screen

    48 adjusting screen adjusting with screen size button • you can adjust screen size or aspect ratio as desired. Press the screen size button. • the current screen size will be displayed on the screen. • each time you press the screen size button on the remote control, a different screen size appears....

  • Page 48: Adjusting Screen In The Menu

    49 adjusting screen in the menu adjusting screen • you can adjust the screen in the menu. Press the menu button. • the menu screen as shown below will appear. Press the “ ” button. • press the “ ” buttons to select ‘screen’. 1 2 menu move select exit mode h. Position v. Position auto 48 51 16 : 9 pi...

  • Page 49: Adjusting Screen In The Menu

    50 adjusting screen in the menu press the volume “ ” buttons. • press the volume “ ” buttons to enter the sub menu “screen”. • while you are in ‘screen’ menu, press the “ ” or “ ” button to select a desired item, and then, adjust the value by pressing the “ ” or “ ”. 3 menu move select exit mode h. ...

  • Page 50: Watching A Still Image

    51 press the “still” button. • if you wish to freeze a picture, press the “still” button. You can still hear the sound. • press “still” button again to cancel the “still” function. 1 watching a still image • you can view still images with this function. However, displaying the same images such as st...

  • Page 51

    52 watching two pictures simultaneously engaging pip mode • press the ‘pip’ button once on the remote control to engage the picture-in-picture mode. • by pressing the button repeatedly, it will show the following cycle. • if switched to p-by-p (picture-by-picture) mode, the screen will be split in h...

  • Page 52

    Select the program • using program up/down buttons ( pr /pr ) , you may select the desired channels for sub-pictures. • the pr up/down buttons select the tv channels. Available pip input combinations • main-picture and sub-picture input combinations are listed below for reference. 6 4 select the inp...

  • Page 53: Selecting Sound Mode

    Selecting sound mode 54 selecting sound mode • enjoy various sound modes by selecting your favourite sound mode depending on the kinds of moving pictures. Select “sound mode”. • press the “s.Mode” on the remote control. • while pressing the “s.Mode” for the first time, the current sound mode will be...

  • Page 54: Customising Sound Mode

    Customising sound mode • this feature allows the user to adjust for their preference. 55 press the “ ” button. • select [sound] by the “ ” buttons, then press the “ ” button to display the following. Select sound balance. • select “sound-balance” by the “ ” buttons, then adjust it. 3 press the menu ...

  • Page 55

    56 language selection for dual language broadcast • if a programme is received in two languages (dual language), you can switch to dual i, dual ii or f mono by pressing the button of the remote control repeatedly. Dual i dual i sends the primary broadcast language to the loudspeakers. Dual ii dual i...

  • Page 56: Customising Sound Mode

    57 select the sound mode. 5 move adjust menu exit balance effect avc mode equalizer off off normal 0 picture screen sound feature install • select the sound mode by pressing the “ ” buttons, then adjust it by pressing the “ ” buttons. * normal : suitable for watching any motion picture * movie : sel...

  • Page 57: Selecting Input Signal

    Selecting input signal 58 notes: 1) if an external device is not connected or input signal is not applied a warning message (“no signal”) will be displayed. 2) in this case, check if external device is connected and/or terminal connection is properly fitted. 3) also, you can select input using [inpu...

  • Page 58

    59 59 checking the current input signal • used to check the input signal mode, current time, resolution, channel, etc. Press the recall button. • press the [recall] button on the remote control. 1 1. If you watch component, pc, or hdmi: displays which input terminal is used, and indicates the input ...

  • Page 59

    60 menu background, language and child lock setting press the menu button. • the menu screen will be displayed as below. Press the “ ” button. • select [feature] by the “ ” button. Select the menu background. • select the menu [background] by pressing the “ ” button. • adjust the translucent level o...

  • Page 60

    61 select language by using the “ ” button. • select [language] by using the “ ” button. • every press of the “ ” button while you are in the [language] mode would cycle through the different languages. Child lock setting • select [child lock] by the “ ” buttons. • whenever “ ” button is pressed, th...

  • Page 61

    62 mgdi plus (meta genuine digital image) press the menu button. • the menu screen will be displayed as below. Select feature • select [feature] by the “ ” button. Mgdi plus setting • enter the sub menu by using the “ ” button. • select the [mgdi plus] by pressing the “ ” button. • you can select [m...

  • Page 62

    63 press the mgdi button on the remote control. • pressing the “mgdi” button first time will display the current setting for mgdi plus. • to cancel the mgdi plus, press the “mgdi” button to select ‘off’. 4 move adjust menu exit background language child lock mgdi plus auto power time setting ism ini...

  • Page 63: Auto Power Setting

    64 auto power setting auto power setting • select the [auto power] by pressing the “ ” button from [feature]. • you can select [auto power] on and off mode by using the “ ” button. 1 move adjust menu exit background language child lock mgdi plus auto power time setting ism initialize english off on ...

  • Page 64: Time Setting

    65 press the menu button. • the menu screen will be displayed as below. Select feature • select [feature] by the “ ” button. Select time setting • enter the sub menu by using the “ ” button. • select the [time setting] with the “ ” button. • enter [time setting] by pressing the “ ” button. 3 1 2 mov...

  • Page 65: Time Setting

    66 time setting time setting • the “current time” must be set up ahead of setting up other time memories. Off-time and wake time setting • select functions by pressing the “ ” button. First, set [clock]- current time, and then you can setup off-time and wake time. • [clock] : adjust the desired hour...

  • Page 66

    67 press the menu button. • the menu screen will be displayed as below. Press the “ ” button. • select [feature] by the “ ” button. Select ism. • enter the sub menu by using the “ ” button. • select the [ism] by pressing the “ ” button. • press of the “ ” button while you are in the ism. 3 1 2 move ...

  • Page 67

    68 image sticking minimisation(ism) select functions. • every press of the “ ” button after select function by the “ ” button would switch between on/off. 4 move adjust menu exit ism pixel shift low bright image invert off off off picture screen sound feature install notes: * pixel shift : the whole...

  • Page 68: Initialize Setting

    69 back to initialization • you can restore the values of the adjustment setting made in the menu back to factory settings. Press the menu button. • the menu screen will be displayed as below. 1 move select menu exit mode brightness contrast sharpness colour colour temp. N.R. Normal normal on 50 50 ...

  • Page 69: Initialize Setting

    70 initialize setting when [initialization] is completed: 1) when [initialization] is completed, those values that have been set in the user mode of [picture mode] and [sound mode] will be returned to the factory preset values. 2) once initialized, you can not undo. 3) the items in the [screen] menu...

  • Page 70: Setting Sleep Timer

    71 setting sleep timer setting sleep timer • sleep timer turns the pdp off after a preset time. Press the “sleep” button. • press the “sleep” button on the remote control. • pressing the “sleep” button first time will display the current setting for sleep timer. • to cancel the sleep timer, press th...

  • Page 71: Teletext

    72 teletext switching teletext on/off • press the text button ( ) the index page or the page viewed last will appear. Press the text button again to return to the tv mode. Selecting pages • the page selector button 0~9 are used to enter a page number. The selected page number appears at the top of t...

  • Page 72

    73 reveal answer • this function can be used on certain pages to reveal the solution of riddles. Press the reveal button ( ) to reveal a hidden answer and press again to hide it. Doubling character size • repeatedly pressing the size button ( ) doubles the character size in the following order. Uppe...

  • Page 73: Before Requesting Service

    74 74 before requesting service before requesting for service s t y o mm p s c h e c k s a c t i o n • there are empty spots at the top and the bottom area of the screen. • check if the screen size of an image is wider than 16:9 aspect ratio (theatre screen size). • when video screen is wider than 1...

  • Page 74: Specifications

    Specifications * appearance and specifications of this product are subject to change for improving the product without prior notice. Display unit connection terminal audio features items video audio hdmi input hdmi jack pc input one 15 pin d-sub jack phone jack component input one y, pb/cb, pr/cr rc...

  • Page 75

    48586900e10u-r0