- DL manuals
- Daewoo
- DVD Player
- DVD-T6300N
- Service Manual
Daewoo DVD-T6300N Service Manual
Component Descriptions
DVD PLAYER
1. Precautions
2. Reference Information
3. Product Specification
4. Operating Instructions
5. Disassembly and Reassembly
6. Troubleshooting
7. Electrical Part List
8. Block Diagram
9. PCB Diagrams
10. Wiring Diagram
11. Schematic Diagrams
12. Oscillograms
CONTENTS
MANUAL
SERVICE
DVD PLAYER
DVD-T6300N
Summary of DVD-T6300N
Page 1
Component descriptions dvd player 1. Precautions 2. Reference information 3. Product specification 4. Operating instructions 5. Disassembly and reassembly 6. Troubleshooting 7. Electrical part list 8. Block diagram 9. Pcb diagrams 10. Wiring diagram 11. Schematic diagrams 12. Oscillograms contents m...
Page 2
2 1) before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items: (1) be sure that no built-in protective devices are defective or have been defeated during servicing. (1) protective shields are provided to p...
Page 3
3 (5) within the limits specified, there is the possibility of a shock hazard, and the instrument must be re-pared and rechecked before it is returned to the customer. See fig. 1-2. Fig. 1-2 insulation resistance test 2) read and comply with all caution and safety related notes non or inside the cab...
Page 4
4 caution : before servicing instruments covered by this service manual and its supplements, read and follow the safety precautions section of this manual. Note : if unforeseen circument create conflict between the following servicing precautions and any of the safety precautions, always follow the ...
Page 5
5 electrostatically sensitive devices (esd) some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called electrostatically sensitive devices(esd). Examples of typical esd devices are integrated circuits and some field-effect transistors an...
Page 6
6 recommended operating conditions item symbol min. Typ. Max. Unit supply voltage vcc 4.75 5.0 5.25 v high level input voltage vih 2.0 - vcc v low level input voltage vil 0 - 0.8 v *this is an optional output. 2-1-1 fiber optic transmitting module for digital audio equipments (totx178) 2. Reference ...
Page 7
7 component descriptions 2-1-2 ntsc/pal digital video encoder (adv7170).
Page 8
8 component descriptions.
Page 9
9 component descriptions.
Page 10
10 features l single-chip dvd video decoder in a 208-pin pqfp package l supports mpeg-1 system and mpeg-2 program streams l programmable multimedia processor architecture l compatible with audio cd, video cd, vcd 3.0, and super video cd(svcd) l dvd navigation 1 l built-in content scrambling system(c...
Page 11
11 functional description component descriptions.
Page 12
12 component descriptions pinout diagram.
Page 13
13 pin descriptions name number i/o definition vcc 1, 9, 18, 27, 35, 44, 51, 59, 68, 75, 83, 92, 99, 104, 111, 121, 130, 139, 148, 157, 164, 172, 183, 193, 201 i 3.65 v ± 150 mv. La[21:0] 23:19,16:10,7:2,207:204 o device address output. Vss 8,17,26,34,43,52,60,67,76,84,91,98,103, 112,120,129,1 38,14...
Page 14
14 component descriptions name number i/o definition hsynch# 119 i/o horizontal synch for screen video interface, programmable for rising or falling edge, active low. Hd[15:0] 141:140, 137:131, 128:122 o host data bus hcs1fx# 152 o host select 1. Hcs3fx# 153 o host select 3. Hiocs16# 151 i device 16...
Page 15
15 component descriptions 2-1-4 digital-to-analog stereo audio converter (cs4391).
Page 16
16 component descriptions.
Page 17
17 component descriptions.
Page 18
18 component descriptions.
Page 19
19 features fully static design 8-bit cmos microcontroller 256 bytes of on-chip scratchpad ram 8 kb electrically erasable/programmable mtp-rom 64 kb program memory address space 64 kb data memory address space four 8-bit bi-directional ports three 16-bit timer/counters one full duplex serial port(ua...
Page 20
20 component descriptions block diagram absolute maximum ratings parameter symbol min. Max. Unit dc power supply vdd-vss -0.3 +7.0 v input voltage vin vss -0.3 vdd +0.3 v operating temperature ta 0 70 °c storage temperature tst -55 +150 °c.
Page 21
21 pin descriptions symbol descriptions ea# external access enable: this pin forces the processor to execute out of external rom. It should be kept high to access internal rom. The rom address and data will not be presented on the bus if ea pin is high and the program counter is within on-chip rom a...
Page 22
22 features • low-voltage and standard-voltage operation – 5.0 (v cc = 4.5v to 5.5v) – 2.7 (v cc = 2.7v to 5.5v) – 2.5 (v cc = 2.5v to 5.5v) – 1.8 (v cc = 1.8v to 5.5v) • internally organized 128 x 8 (1k), 256 x 8 (2k), 512 x 8 (4k),1024 x 8 (8k) or 2048 x 8 (16k) • 2-wire serial interface • schmitt...
Page 23
23 component descriptions features • 5.0v±40% for read and write operations • access time –70max • current –20 ma typical active read current –30 ma typical program/erase current –1µa typical cmos standby • flexible sector architecture – 8 uniform sectors of 64 kbyte each – any combination of sector...
Page 24
24 block diagram pin descriptions absolute maximum ratings ambient operating temperature ...................... -55°c to +125°c storage temperature ...................................…. -65°c to +150°c voc ground .……………………………………..-2.0v to +7.0v output voltage…………………………………… -2.0v to +7.0v component d...
Page 25
25 component descriptions 2-1-8 256k x 16dynamic ram(t224162b) features n industry-standard x 16 pinouts and timing functions. N single 5v power supply. N all device pins are ttl-compatible. N 512-cycle refresh in 8ms n refresh modes: /ras only, /cas before /ras (cbr) and hidden. N extended data-out...
Page 26
26 block diagram pin configurations component descriptions.
Page 27
27 2-1-9 1mbit(x8) multi-purpose flsh (sst39sf010a) features pin configurations component descriptions.
Page 28
28 block diagram pin descriptions component descriptions.
Page 29
29 2-1-10 system reset monolithic ic pst91xx series features pin assignment component descriptions.
Page 30
30 component descriptions 2-1-11 sp3721a : 6ax dvd analog front end chip features n supports age and equalizer/filter for cd 3x to 32x and dvd 1x to 6x (with rx=8.2kohm) n low power operation (350mw typical @5v) n bi-directional serial port register access n register programmed power management (sle...
Page 31
31 component descriptions channel n 40 mhz bandwidth n supports individual rf inputs for dvd (differential or single-ended) and cd (single ended) n supports internet summing mode for rf signal for dvd and cd respectively n programmable attenuator (min;-24db, 4-bit resolution) n fast attack/decay mod...
Page 32
32 component descriptions pin configurations.
Page 33
33 component descriptions pin description table name number type description input pins dvdrfp, dvdrfn 1,2 i rf signal inputs. Differential rf signal attenuator input pins corf 63 i rf signal input. Signal-ended rf signal attenuator input pin aip, ain 59,60 i agc amplifier inputs. Differential agc a...
Page 34
34 component descriptions pin description table (continued) name number type description analog pins: byp 56 i/o the rf agc integration capacitor cbyp, is connected byp and vpa cp 9 i/o differential phase tracking lpf pin. An external capacitance is connected between this pin and the cp pin. Cn 10 i...
Page 35
35 component descriptions 2-1-12 dvd-rom controller chip (m5705) pin configurations.
Page 36
36 component descriptions block diagram.
Page 37
37 component descriptions pin description table name number type description servo date slicer interface pins xsrfin 2 i/a analog rf signal input xsipin 3 i/a inverting input pin of data slicer xsdsslv 5 o/a slice level output pin xsrslint 6 i/a reference current setting pin for analog data slicer s...
Page 38
38 component descriptions pin description table (continued) name number type description servo control interface pins xsdfct 29 i defect detection signal input xscsj 30 o chip selection signal for accessing control registers xsclk 31 o clock output for accessing control registers xsdata 32 i/o regis...
Page 39
39 component descriptions pin description table (continued) name number type description microcontroller interface pins xgpio[3.0] 48,50, 51,52 i/o these pins are used as general purpose i/o bus xmp1-7 40 i/o internal microcontroller programmable i/o port 1.7 xmp1-6 41 i/o internal microcontroller p...
Page 40
40 component descriptions pin description table (continued) pin name pin no. Type description host interface pins xhcs1j 94 i this pin is used to select the command block task file registers xhcs3j 93 i this pin is used to select the control block task file registers. Xhiorj 103 i asserted by the ho...
Page 41
41 component descriptions pin description table (continued) pin name pin no description power pins avdd5 ds 4 analog power for data slicer part avdd5 da 14 analog power for dac part avdd5 ad 28 analog power for adc part avdd5 pl 168 analog power for data pll part vdd 7,55,76 115,146 150,162 power +3...
Page 42
42 n playback system dvd video video cd (1.1, 2.0, 3.0) svcd and cvd cdda cd-rom with mp3 data n television signal system n video performance video out 1 vpp / 75 ohm s-video out y : 1 vpp / 75 ohm c : 0.286 vpp / 75 ohm component out 0.7 vpp / 75 ohm d/a converter 27mhz / 10bit n audio performance ...
Page 43
43 n connections coaxial digital audio out x1 audio analog out for 2-channel x1 component video (y,pb,pr) x1 composite video out x1 s-video out x1 optical audio out x1(option) n power supply power source ac 90~250v, 50/60hz power consumption n set dimensions (w x h x d) 420 x 84 x 270 (mm ) net weig...
Page 44
44 connecting to audio equipment & tv connecting to a monaural tv set 4. Operating instructions 4-1 basic connections audio equipment tv set connecting to tv (for video) method1: dvd player + tv with video input jack method2: dvd player + tv with s-video jack method3: dvd player + tv with component ...
Page 45
45 connecting to a decoder with a dolby digital or dts processing tv set operating instructions coaxial audio cable (optional) to coaxial digital audio input optical audio cable (optional) to optical digital audio input front surround center surround subwoofer decoder or amplifier with dolby digital...
Page 46
46 press setup button and select video submenu on setup screen. After that, select tv type by pressing down arrow button ( ▼) until desired tv mode is selected. For more information, refer to 7.2 video on the instruction manual. When a dvd disc is loaded, select desired menu item using arrow button ...
Page 47
47 use arrow button and select an mp3 title using the select button then play will start automatically. When you know the title number, enter the mp3 title number using numeric buttons and press the se- lect button. If you want to play an adjacent mp3 title, press the next button for next title and ...
Page 48
48 when you want to view the disc contents very slowly in forward or reverse direction, you can do that by pressing the ff/sf button ( ) or the fr/sr button ( ) during pause mode. There are total 3 steps for dvd and vcd. They are slow 1/2x, slow 1/4x and slow 1/8x for both direction. The slow revers...
Page 49
49 some dvd discs may contain scenes, which have been shot simul- taneously from a number of different angles. If the loaded disc su- pports multiple angles, you can see indicator on the fluorescent display and the tv screen. In the figure shown right, there are total 9 angles. To switch to the angl...
Page 50
50 fig. 1 fig. 2 fig. 3 fig. 4 ` fig. 5 fig. 6 5. Disassembly and reassembly 5-1 open top cabinet let’s begin to disassemble ! Remove 4 screws on back top cabinet. Remove 4 screws on the left and right side. Lift up the cabinet in direction of arrow. You have to lift up in direction of arrow, certai...
Page 51
51 fig. 7 fig. 8 fig. 9 fig. 10 remove 3 screws on the rear panel. Disassemble the power cord. Disjoint a rear panel from body, direction of arrow. View of dissembly, top cabinet and rear panel. ① ② ③ 5-2 rear panel removal.
Page 52
52 fig. 11 fig.12 fig.13 fig.14 fig.15 insert a sharp point into emergency hole, and then push the tap in the hole in direction of arrow, open tray manually. Remove 2 screws. Remove 3 screws. Disconnect cn7 from main pcb and ‘cn3’ from smps pcb. Remove 1 screw. Emergency hole ① ② ① ② ③ 5-3 ass’y fro...
Page 53
53 fig. 16 fig.17 fig.18 fig.19 fig. 20 fig. 21 release 3 taps from the bottom cabinet. Disassemble the ass’y front panel. Remove 9 screws, and disassemble the front pcb release 2 taps on the left and right side from the bottom cabinet. Disassemble the door tray in direction of arrow. ① ② ③ ④ pictur...
Page 54
54 fig. 22 fig. 23 fig. 24 fig. 25 fig. 26 disconnect ‘cn5’ from main pcb. Remove 4 screws, and dissemble smps. Remove 2 screws. Disconnect jack pcb from main pcb. ① ② ① ② ③ ④ 5-4 jack pcb and smps removal.
Page 55
55 fig. 27 fig. 28 fig. 29 when you take the dvd player apart, you can see this picture. Remove 7 screws. Disassemble deck and main pcb. ③ ② ④ ⑤ ⑦ ① ⑥ 5-5 deck and main pcb removal.
Page 56
56 asds an appearance requires confirmation no power insert the ac power plug securely into the power outlet. No picture make sure that the equipment is connected properly. Make sure that the input setting for the tv is video (av). No sound make sure that the equipment is connected properly. Distort...
Page 57
57 1. Main board 7. Electrical part list.
Page 58
58 electrical part list.
Page 59
59 2. Front board front board sc type location no spec pak' no p c b a s s ' y , f r o n t ( m / i ) 1 (ir)infra reciever l type u2 2 tr to-92 q1 3 vfd display u3 4 front power wire, 5pin-5pin(pcb), pcb in wire con2 5 front signal wire, 11pin-11pin(pcb), pcb in wire con1 6 tact s/w, 4pin,5mm 5mm sw1...
Page 60
60 3.Jack board s100 model (for usa) location no spec pak' usa' no a s s ' y o p t i o n 1 aaa, 1.5v, battery 2 a s s ' y a c c e s o r y 1 43key's, remocon(ir) 1 2 rca cable(pin cable) 1 3 s-vhs cable 1 a s s ' y m a i n 1 deck & main board 1 2 smps manual 1 3 2p, ac power cord wire 1 p c b a s s '...
Page 61
61 s100 model (for usa) location no spec pak' usa' no pass'y,out_bd(smd_bottom) 10 chip res', 1/8w,1k ohm j 0603 4 r729,r731,r734,r736 11 chip res', 1/8w,220 ohm j 0603 2 r744,r743 12 chip res', 1/8w,20k ohm j 0603 6 r751,r756,r761,r766,r771,r781 13 chip res', 1/8w,3.3k ohm j 0603 10 r716,r725,r741,...
Page 62
62 4.Smps part list electrical part list.
Page 63
63 electrical part list.
Page 64
64 8. Block diagram main board block diagram.
Page 65
65 9. Pcb diagrams 9-1 main pcb (top).
Page 66
66 9-2 main pcb (bottom) pcb diagrams.
Page 67
67 9-3 jack pcb (top) pcb diagrams.
Page 68
68 pcb diagrams 9-4 jack pcb (bottom).
Page 69
69 9 - 3 front pcb (component side) 9 - 4 front pcb (solder side) pcb diagrams.
Page 70
70 9-5 smps pcb (top side) pcb diagrams.
Page 71
71 10. Wiring diagram wiring diagram.
Page 72
72 11. Schematic diagrams 11-1 smps pcb schematic diagram.
Page 73
73 11-2 front pcb schematic diagram.
Page 74
74 11-3 main pcb schematic diagram.
Page 75
75 main pcb schematic diagram.
Page 76
76 main pcb schematic diagram.
Page 77
77 main pcb schematic diagram.
Page 78
78 main pcb schematic diagram.
Page 79
79 main pcb schematic diagram.
Page 80
80 1 2 3 4 5 main pcb schematic diagram.
Page 81
81 5 6 7 main pcb schematic diagram 4.
Page 82
82 8 9 10 11 only 5.1 ch option main pcb schematic diagram.
Page 83
83 12 13 14 17 15 16 18 19 main pcb schematic diagram.
Page 84
84 schematic diagrams 11-4 jack pcb schematic diagram 21 22.
Page 85
85 20 23 24 11 jack pcb schematic diagram.
Page 86
86 1. 27mhz 2. Rom- data-bus 3. Ram-data-bus 4. 12c-clk 5. 12c-data 6. Hsync 12. Oscillograms.
Page 87
87 7. Vsync 8. Bclk-dvd 9. Lrck-dvd 10. Tsdo 11. Mclk 12. Host-data oscillograms.
Page 88
88 13. Host-clk 14. Host-cs 15. Mc-daco 16. Md-daco 17. Vfd-data 18. Vfd-stb oscillograms.
Page 89
89 19. Vfd-clk 20. Composite-out 21. Coxial-out 22. Optical-out 23. S-video 24. Component out oscillograms.
Page 90
90 memo.