1. DL manuals
  2. Dimension One Spas
  3. Hot Tub
  4. 01510-1030
  5. Installation & Owners Manual

Dimension One Spas 01510-1030 Installation & Owners Manual

Manual is about: Dimension One Spas Sonic Immersion System Owner's Manual and Dealer's Installation Guide

Summary of 01510-1030

  • Page 3

    Sonic immersion system table of contents owner’s manual ......................................................................... 1 f eatures of the s onic i mmersion ................................................. 1 u sing the cd p layer ..............................................................

  • Page 4

    Sonic immersion system iii.

  • Page 5: Owner’S Manual

    Sonic immersion system dealer owners manual owner’s manual features of the sonic immersion • dealer installation allows you to add to any sonic immersion system ready dimension one spa in stock • patented planar magnetic speaker technology (1/4” thick) that generates unparalleled sound quality even ...

  • Page 6: Dealer

    Sonic immersion system dealer installation guide dealer installation this section intended for use by authorized dealer personnel only 2.

  • Page 7: Getting Ready to Start

    Sonic immersion system dealer installation guide getting ready to start the sonic immersion system can only be installed on spas with the following serial numbers. Table 1 sonic immersion system ready spas model serial number aurora hp 91275 or higher aurora ii 91210 and higher (also 91184) aurora x...

  • Page 8: Required Tools

    Sonic immersion system dealer installation guide required tools you will need the following tools to complete the installation: table 2 required tools electric drill 1 ½ inch hole saw ¼ inch drill bit 3/8 inch drill bit saber saw phillips screwdriver tape (masking, electrical, duct, or packaging) ½ ...

  • Page 9

    Sonic immersion system dealer installation guide non ratcheting pvc pipe cutter medium size needle nose pliers wire stripper utility knife 5/16” nut driver or wrench six inch square stapler and staples straight edge safety glasses silicone caulking (clear) small saw 5.

  • Page 10: Parts List

    Sonic immersion system dealer installation guide parts list you should have received the following parts in the sonic immersion system installation kit: table 3 parts list description qty item number this document 1 01510- 1030 amplifier 1 01564-08 coarse- threaded drywall screws 5 01051-06 template...

  • Page 11

    Sonic immersion system dealer installation guide speakers, satellite 2 01564-14 stereo 1 01564-03 sub-woofer sub assembly 1 01564-09 stereo cover, marine 1 01564-04 dual pole antenna 1 01564-05 preamp stereo, cable 2 01570-24 power supply screw, sheet metal, ss, ph 2 01011-38 7.

  • Page 12: Removing Panels

    Sonic immersion system dealer installation guide marine cover screws, #8 x ½” ss truss head 4 01011-40 cable ty, 4” black 10 01200-006 cable ty mount 10 01200-005 removing panels in order to install the system up to three panels must be removed from the spa: the equipment compartment panel, the pane...

  • Page 13

    Sonic immersion system dealer installation guide 3. Locate the spa’s main top side control. 4. The lower control is located in the equipment compartment behind the spa panel below the main top side control. 5. Use the screwdriver to remove the equipment compartment panel screws. 9.

  • Page 14: Panel

    Sonic immersion system dealer installation guide the number of screws to be removed will depend on the model of spa. Remove the sub woofer compartment panel the installation location of the sub woofer compartment will vary from one spa model to another. Use table 3 to locate the compartment on your ...

  • Page 15

    Sonic immersion system dealer installation guide sub-woofer table 4 model list model and number location of installation aurora ii and chairman chairman ii and aurora xlt diplomat, californian nautilus 11.

  • Page 16

    Sonic immersion system dealer installation guide caliente hp, triad ii, aurora hp, and triad 1. Use the screwdriver to remove the spa panel screws. The number of screws to be removed will depend on the model of spa. 12.

  • Page 17: Installing The Sub Woofer

    Sonic immersion system dealer installation guide installing the sub woofer compartment the installation of the sub woofer compartment consists of removing the panel, removing the paper cover, exposing the plug, removing the plug, and installing the sub woofer compartment. 1. If you have a spa with w...

  • Page 18

    Sonic immersion system dealer installation guide the photograph above may not look like your spa, refer to table 3. 3. Once the plug is exposed, use a screwdriver to punch holes in the foam large enough to insert your hands and pull the plug out of the spa. The plug may not come out in one piece. 14.

  • Page 19

    Sonic immersion system dealer installation guide 4. Use a medium size pair of needle nose pliers to remove the large staples in the bottom rail where the plug was removed. 5. Remove all remnants of the plastic bag inside the compartment where the plug was removed. This will expose the electrical con...

  • Page 20

    Sonic immersion system dealer installation guide 6. Using a non-ratcheting pvc pipe cutter, trim the electrical conduit flush with the foam wall. 16.

  • Page 21

    Sonic immersion system dealer installation guide 7. Locate the sub woofer sub assembly (p/n 01564-09). Locate the spot on the compartment that matches the location of the conduit in the spa. Using a1½ inch hole saw, drill a hole for the conduit. 8. Try to place the sub woofer compartment into the sp...

  • Page 22

    Sonic immersion system dealer installation guide 9. A properly positioned sub woofer compartment is shown in the following photograph. 18.

  • Page 23: Pre Wiring From Equipment

    Sonic immersion system dealer installation guide 10. Once you are satisfied that the compartment fits properly, secure the compartment to the frame with 5 1“ coarse- threaded drywall screws (p/n 01051-06 provided in hardware package). Pre wiring from equipment compartment to sub woofer compartment 1...

  • Page 24

    Sonic immersion system dealer installation guide 2. Now locate the amplifier cables (two white and two red rca connectors on both ends, p/n 01570-24). Locate the three- branched harness assembly (p/n 01564-20). One branch will be considerably longer than the other two. 3. Attach the preamp stereo ca...

  • Page 25

    Sonic immersion system dealer installation guide 4. Apply a small amount of fish tape lubricant to a cloth and then run the cables through the rag to give them a light coating of lubricant. 5. Now pull them through the conduit from the equipment compartment to the sub-woofer compartment. 6. Now that...

  • Page 26

    Sonic immersion system dealer installation guide longer than necessary. Make sure that when the wires are connected to the amplifier that the amplifier can be moved out to make adjustments. Using a wire stripper, strip approximately ½ inch of insulator from the 3 conductor wires. 7. Connect the blac...

  • Page 27

    Sonic immersion system dealer installation guide 8. Locate the wire coming from the sub-woofer. This wire is covered with clear insulator. The wire has two conductors. One is copper-colored and the other is silver. Strip approximately ½ inch of insulator from each wire and twist each to form a tight...

  • Page 28: Installation of Power Supply

    Sonic immersion system dealer installation guide 10. Set gain ch 1 and ch 2 to 0.5v position. 11. Set mode to the 3ch position. 12. Set bass boost ch1 and ch 2 to the min position. 13. Set high pass ch 1 and ch 2 to the 200 hz positions. 14. Set ch 1 to hp position and ch 2 to lp position. Installat...

  • Page 29

    Sonic immersion system dealer installation guide 1. Connect the wires from row 1 (120 v supply) to the power supply as follows: black wire to the terminal marked ”ac-l”, the white wire to terminal marked “ac-n”, and the green wire to the terminal marked “fg”. 25.

  • Page 30

    Sonic immersion system dealer installation guide 2. Connect the wires coming from row 2 (stereo +12 v supply) as follows: (see picture below) yellow and red wires to terminal marked “dc+” and the black wire to terminal marked “dc-“. 3. Connect the wires coming from row 3 (amplifier) as follows (see ...

  • Page 31: Compartment

    Sonic immersion system dealer installation guide installing power supply in equipment compartment 1. Turn the power supply so that you can see the voltage selector switch, see picture below, and place the switch in the correct position (115v for ul and csa spas or 240v for ce spas) for your location...

  • Page 32

    Sonic immersion system dealer installation guide 3. Locate the connector on the harness assembly that matches the one that you just installed on the power supply and connect them together. 28.

  • Page 33: Wiring The Power Supply

    Sonic immersion system dealer installation guide wiring the power supply 1. Locate the end of the harness that has a green, black, and white wire (with connectors). Remove lower control box cover. Insert these wires through the hole in the bottom of the lower control box. 2. Using a 5/16” nut driver...

  • Page 34

    Sonic immersion system dealer installation guide 3. Now place the green ground wire that you just inserted into the lower control box over the screw, replace 5/16” nut, and secure with 5/16” nut driver or wrench. 4. Connect the white and black wires to the pins as outlined in the following table. Ta...

  • Page 35

    Sonic immersion system dealer installation guide determining location of cd weather cover the installation location of the cd player weather cover (p/n 01564-04) depends on the model of the spa. The following steps will guide you through the process of determining the installation location. 1. Refer...

  • Page 36: Assembly

    Sonic immersion system dealer installation guide it is important that the ruler or square (see picture on previous page) be kept level and at the top of the recess area while making these measurements. 2. Use the measurements determined in step 1 and insert them into the following formula: distance ...

  • Page 37

    Sonic immersion system dealer installation guide 2. Using measurement obtained for horizontal position (hp), measure from side of panel, see below, and mark spot with a fine point marker. 3. The point where these two lines intersect is the upper right corner of the template (p/n doc 74 rev a). 4. Al...

  • Page 38

    Sonic immersion system dealer installation guide 7. Using a 3/8”bit, drill holes in two corners of the rectangle. Make certain that the holes are within the lines. Using a center punch to mark the drilling centers will prevent the drill bit from wandering. 8. Using a saber saw, cut out the rectangul...

  • Page 39

    Sonic immersion system dealer installation guide installation of cd player door and bezel if the bezel is not removed from the door assembly (p/n 01564-04), remove it by pulling from the bottom of the bezel and then proceed as follows: 1. Place the door assembly in the cutout. Make certain the door ...

  • Page 40

    Sonic immersion system dealer installation guide to prevent wood panels from splitting, driil pilot holes before installing the door assembly. 3. Reattach the bezel. 4. Locate the mounting sleeve supplied with the cd player and refer to the cd player owner’s manual for directions on how to install t...

  • Page 41

    Sonic immersion system dealer installation guide 3. Reattach panel to spa. 4. Connect antenna, main harness and amplifier to cd player as described in cd player owner’s manual. Connect power supply cable (long branch of main harness) to power supply connector on cd player. Connect channel 1 preamp s...

  • Page 42

    Sonic immersion system dealer installation guide 1. Take the hinge mounting bracket connected to the speaker (p/n 01564-14) and place it on the panel with the top triangular portion of the hinge butting up against the lower edge of the overhanging spa lip. 2. Remove the protective caps from the hing...

  • Page 43

    Sonic immersion system dealer installation guide 39.

  • Page 44

    Sonic immersion system dealer installation guide installing the satellite speaker wires 1. Remove the panel where you just finished installing the speakers. 2. Locate two speaker wire sets (p/n 01564-21). The wires have clear insulator with a silver and copper wire and female connectors on one end. ...

  • Page 45

    Sonic immersion system dealer installation guide 41.

  • Page 46

    Sonic immersion system dealer installation guide 5. Continue installing the wire until you reach the panel where the sub-woofer compartment has been installed. Now use the cable tyes and cable mounts to attach the wire to the wood until you reach the sub woofer compartment. 6. Trim any excess wire l...

  • Page 47

    Sonic immersion system dealer installation guide 8. Now connect the wires coming from the sub-woofer compartment to the satellite speakers. The wires from the speakers have male connectors and the wires coming from the sub-woofer have female connectors. 9. Place the panel back on the spa and secure ...

  • Page 48: Securing The Amplifier

    Sonic immersion system dealer installation guide securing the amplifier now that the speakers have been installed and the amplifier has been adjusted it can be secured to the frame with dry wall screws supplied in the kit (p/n 01051-06). Complete the installation replace the spa panels to complete t...

  • Page 50

    Part no. 01510-1030 rev a  2002 dimension one spas.