Dimplex DGP Series Installation Instructions

Model(s)

Volts

Watts

A (Figure 1)

B (Figure 1)

C (Figure 2)

D (Figure 2)

E (Figure 2)

Weight

DGP1000-B

208 / 240

0.75 kW / 1 kW

700 mm / 27.6" 107 mm / 4.25"

560 mm / 22" 300 mm / 11.8" 255 mm / 10" MIN

14.8 kg / 32.6 lbs.

DGP1500-B

208 / 240 1.125 kW / 1.5 kW 770 mm / 30.3" 107 mm / 4.25" 630 mm / 24.8" 300 mm / 11.8" 255 mm / 10" MIN

16.4 kg / 36.2 lbs.

DGP2000-B

208 / 240

1.5 kW / 2.0 kW

840 mm / 37.0" 107 mm / 4.25" 800 mm / 31.5" 300 mm / 11.8" 255 mm /  10" MIN

19.5 kg / 42.9 lbs.

7210370100R01

INDGCAP7RG

Glass Panel Heater

DGP Series

 Installation Instructions

Important InstructIons

When using electrical appliances, basic precautions should always 

be followed to reduce the risk of fire, electric shock, and injury to 

persons, including the following:

Read all instructions before using this appliance.

1. 

The wall bracket supplied with the appliance must be used.

2. 

WArnInG: This heater is hot when in use. To avoid burns, do 

not let bare skin touch hot surfaces. Keep combustible materials, 

such as furniture, pillows, bedding, papers, clothes, and curtains 

at least 3 feet (0.9 m) from the front of the heater.

Extreme caution is necessary when any heater is used by 

3. 

or near children or invalids and whenever the heater is left 

operating and unattended.

Do not use this heater in the immediate surroundings of a bath, 

4. 

shower, pool or other water basin. 

Check and observe all local 

electrical and building codes for minimum clearances from 

electrical switches and circuits before installing this unit.

If the heater is installed in a room containing a bath or shower, 

5. 

it must be installed in such a way that all controls are out of 

reach of a person using the bath or shower. 

Do not use outdoors.

6. 

A heater has hot and arcing or sparking parts inside. Do not 

7. 

use it in areas where highly flammable substances are used 

(e.g. solvents, etc.) or stored.

To prevent a possible fire, do not block air intakes or exhaust 

8. 

in any manner. Do not use on soft surfaces, like a bed, where 

openings may become blocked. Do not place material or 

garments on the heater, or obstruct the air circulation around 

the heater, for instance by curtains or furniture, as this could 

cause overheating and a fire risk.

Do not insert or allow foreign objects to enter any ventilation or 

9. 

exhaust opening as this may cause an electric shock or fire, or 

damage the heater.

Use this heater only as described in this manual. Any other use 

10. 

not recommended by the manufacturer may cause fire, electric 

shock, or injury to persons.

SAVE tHESE InStruCtIonS

A

565

B

150 

Min.

300 Min.

shelf

150 Min.

Electrical Connection

Verify that the supply voltage is the same as that stated on the 

heater (A.C supply only).

This heater is designed for use on a 208/240V 60Hz AC single-

phase supply. Connection requires a supply wire that must consist 

of two wires plus ground and have a rating capable of handling all 

loads on the circuit.  

Make all relevant electrical connections within an installed 

junction box and ensure all wiring meets all local electrical and 

building codes. Where local code requires the disconnection of all 

ungrounded supply lines, a double pole isolating switch must be 

fitted to facilitate isolation.

Connection to the heater should be made using the provided fitted 

cable clamp assembly at the back of the heater to meet local code 

requirements.

WArnInG: Always use a qualified and licensed electrician for 

all wiring and electrical connections.  Improper wiring could lead 

to a fire hazard.

Wall Mounting

!

 IMPortAnt: The wall bracket supplied with the appliance 

must be used. The heater should be positioned observing the 

minimum clearances stated around the heater (Figure 1).

WArnInG: Do not locate the heater immediately below a fixed 

socket outlet or connection box.

Remove wall mounting bracket from the back of the heater by 

1. 

depressing the spring latch at the top of each bracket (Figure 

2).

Fix the wall bracket securely to the wall through the four (4) 

2. 

screw holes provided.

Present the heater to the wall bracket and engage lower slots in 

3. 

the back with bracket.

Raise the heater to upright position and push the heater onto 

4. 

bracket to engage top latch.

D

255 Min.

C

C 

  D

GFP500      390  300

GFP750      390  300

GFP1000     560  300

GFP1500     630  300

GFP2000     800  300

E

D

C

Figure 2

Figure 1