- DL manuals
- Dimplex
- Electric Heater
- QRAD050
- Operating Instructions Manual
Dimplex QRAD050 Operating Instructions Manual
Summary of QRAD050
Page 1
These instructions should be read carefully and retained for future use. Note also the information presented on the appliance. Q-rad electric radiator models: qrad050 / qrad075 / qrad100 / qrad150 / qrad200 operating instructions manual indeuke3rg issue 2.
Page 2
Important these instructions should be read carefully and retained for future use. Note also the information presented on the appliance. Important safety advice when using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock, and injury to p...
Page 3
Warning – this appliance must be earthed the electrical installation must be carried out by a competent electrician, and be in strict accordance with the current i.E.E. Regulations for electrical equipment in buildings. The wires in this mains lead are coloured in accordance with the following code:...
Page 4
General the heater is designed for wall mounting using the wall bracket supplied. It should only be operated when in the upright position as shown - see fig. 1 and fig. 2. All models are splash proof to ip24 standard and may be used in bathrooms, however not in the immediate vicinity of baths, showe...
Page 5
Fig. 1 fig. 3 150 mm (min) 150 mm (min) 546 mm a 105 mm shelf 300 mm model (s) a (mm) qrad050 225 qrad075 225 qrad100 387 qrad150 468 qrad200 630 260 mm (min) a 275 mm fig. 2 294 mm (min) 5.
Page 6
Notes to the installer test mode when the heater is connected via a pilot wire system, the test mode allows the installer to confirm that the heater is responding correctly to the incoming pilot wire signal. Pilot wire mode must be enabled in the heater’s settings in order for the appliance to be co...
Page 7
User introduction thank you for choosing the dimplex q-rad electric radiator. We manufacture the highest quality heating products for use in a wide variety of environments. This product has been designed to incorporate the latest, most advanced technologies to give you maximum control over your heat...
Page 8
20 c 0 quick start guide this guide is for quick reference only. Please refer to the operating section for further information. How does the heater control work? The control allows you to choose when you want heat and at what temperature. When using a timer mode (see below), comfort on will display ...
Page 9
Mode timer mode manual eco mode frost protect off which timer mode is best for me? The heater leaves the factory set in out all day mode. If you are out during the day and only require heat in the mornings and evenings then this mode will suit your lifestyle and you won’t need to alter anything. If ...
Page 10
Operation 1 display screen 2 ‘menu’ button 3 ‘back’ button 4 ‘up and down’ arrows 5 ‘enter’ button 6 heating status 7 ‘advance’ button the heater is fitted with an adjustable thermostat enabling the room temperature to be controlled. The minimum room temperature is 7°c. The maximum temperature is se...
Page 11
Control functions the heater controls can be easily adjusted by using the six buttons on the user interface. 1. The display screen shows the options available at each stage of adjustment. 2. Menu – displays the main options list; date/time – set the date and time. Mode – set the mode of operation. O...
Page 12
Main screen setting the date and time after 30 seconds of inactivity the heater will default back to the main screen. Here the chosen temperature is displayed along with the mode of operation. Any use of the advance function will be displayed here, and pressing enter will show the functions which ar...
Page 13
Modes of operation the heater comes pre-programmed with a set of heating profiles. There are four options available - three preset and one user adjustable timer; 1. Out all day (pre-programmed) - has the following preset times monday to sunday, which can be altered if desired; 07.00 until 08.30 17.3...
Page 14
Choosing and setting a mode timer modes to choose a timer mode press menu and to select mode, then press enter. Now select timer mode, again using the enter button. Select the mode required, by pressing the or and enter buttons. For options out all day, home all day and user timer, three choices are...
Page 15
Note: if ecostart (es) is enabled the heater will begin heating the room before the start of the heating period to ensure the room is at the required temperature when the period starts. If disabled the heater will simply start heating at the start of the comfort on period. If ecostart control is dis...
Page 16
Advance 1hr comfort on advance home all day comfort on advance the advance function allows the heating profile of the appliance to be changed temporarily. When a timer has been selected, the advance function is used to begin the next comfort on mode early. If the heater is in comfort off mode and he...
Page 17
Child lock to lock the controls press back and enter for three seconds. Child lock will appear at the bottom of the screen. To unlock the control repeat the action of pressing back and enter for three seconds. Press and hold enter for five seconds to display the user information menu; sp range (set ...
Page 18
Energy saving tips the energy we use to heat, light and power our homes contributes over a quarter of the uk’s carbon emissions, the principle contributor to climate change. Around half the energy used in the home is for heating and hot water, so using your heating system efficiently will not only h...
Page 19
Important during the initial operation, some odour may be noticed due to the newness of materials used in manufacture. This is normal and will disappear after a short period or use. It is however advisable to keep the room well ventilated. Cleaning warning - always disconnect from the power supply b...
Page 20
Patent/patent application this product is protected by one or more of the following patents or patent applications: great britain: gb1304025.8 international: pct/ep2014/054404 this product complies with the european safety standards en60335-2-30 and the european standard electromagnetic compatibilit...