Summary of CARBON-Z YAK 54
Page 1
Instruction manual bedienungsanleitung manuel d’utilisation manuale di istruzioni carbon-z yak 54.
Page 2
En 2.
Page 3
En safety precautions and warnings as the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or the property of others. This model is controlled by a radio signal subject to interference from many s...
Page 4: Table of Contents
En table of contents carbon-z yak 54 specifi cations wingspan length weight (rtf) 48 in (1220mm) 48.5 in (1232mm) 3.75-3.81 lb (1700-1730 g) carbon-z yak 54 features bind-n-fly version plug- n-play version motor bl25 brushless outrunner, 1000kv installed installed esc e-flite® pro 60a brushless with...
Page 5: Charging The Flight Battery
En the battery charging process 1. Charge only batteries that are cool to the touch and are not damaged. Look at the battery to make sure it is not damaged e.G., swollen, bent, broken or punctured. 2. Attach the input cord of the charger to the appropriate power supply (12v accessory outlet). 3. Whe...
Page 6: General Assembly And
En general assembly and maintenance tips note: this checklist is not a replacement for the content included in this manual. Although you can use it as a quick start guide, we strongly suggest reading through this manual completely before proceeding. First flight preparation activity bnf pnp remove a...
Page 7: Installing Landing Gear
En installing landing gear note: you may remove fairings for flying the carbon-z yak 54 from a rough runway. 1. Press together landing gear legs and put landing gear support in slot in bottom of fuselage. 2. Release landing gear when support is fully installed in the fuselage slot. 3. Install fairin...
Page 8: Installing Wings
En installing wings 1. Put the wing tube in the round hole in the wing slot of the fuselage. 2. Put left wing on the wing tube. 3. Move the wing on the tube into the slot in the fuselage while putting the aileron control connector in the fuselage. 4. Secure left wing to fuselage using screws. 5. Ins...
Page 9: Pushrods On Control Horns
En installing horizontal tail and pushrods on control horns installing the horizontal tail 1. Put the horizontal stabilizer tube in the round hole located in the horizontal stabilizer slot of the fuselage. 2. Slide the left horizontal stabilizer onto the stabilizer tube. 3. Slide the right horizonta...
Page 10
En installing the flight battery note: before flying and after centering control surfaces, rebind the aircraft so control surfaces are neutral when you plug in the flight battery. Caution: install receiver and connect the speed control into the throttle channel (for pnp) before installing the flight...
Page 11
En removing the control surfaces to remove the control surfaces, follow the steps listed below: elevator 1. Disconnect the clevis from the control horn. 2. Remove the machine screws located on the bottom of the horizontal stabilizer. Then remove the horizontal stabilizer from the fuselage. 3. Remove...
Page 12: Removing Propeller Adapter
En removing propeller adapter, propeller and spinner note: the information on this page is for maintenance of the yak 54. Spinner, propeller and propeller adapter damage can result from aircraft crashes. Caution: do not handle propeller parts while the flight battery is connected to the esc. Persona...
Page 13: Pnp Installation
En 4. To install the motor: slide the 4 motor wires through the guide holes and slide the motor all the way into the nose. Note: when installing the new motor do not attach the “x” mount until last. This will make connecting the 3 motor wires much easier. 5. Plug the 3 motor wires into the esc, maki...
Page 14
En note: the carbon-z yak 54 can be taken apart and put back in the box for storage or transportation. Note: the carbon-z yak 54 is a high-performance aircraft, designed to handle the stresses of high- energy aerobatic flight. Due to the construction of the carbon-z yak 54, the airframe is capable o...
Page 15: Troubleshooting Guide
En troubleshooting guide problem possible cause solution aircraft will not respond to throttle but responds to other controls • esc is not armed. • throttle channel is reversed • lower throttle stick and throttle trim to lowest settings. • reverse throttle channel on transmitter extra propeller nois...
Page 16: Replacement Parts
En replacement parts here is a list of replacement parts to repair or keep your carbon-z yak 54 flying. These parts are available at your local hobby shop or from horizon hobby (www.Horizonhobby.Com). Please try your local hobby shop first. By supporting them, they will be there when you need them. ...
Page 17: Warranty and Repair Policy
En warranty and repair policy warranty period exclusive warranty- horizon hobby, inc., (horizon) warranties that the products purchased (the “product”) will be free from defects in materials and workmanship at the date of purchase by the purchaser. Limited warranty horizon reserves the right to chan...
Page 18: Contact Information
En contact information compliance information for the european union declaration of conformity (in accordance with iso/iec 17050-1) no. Hh2010080903 product(s): carbon-z yak 54 bnf/pnp item number(s): efl10080/efl10075 equipment class: 1 the object of declaration described above is in conformity wit...
Page 19
? 2010 horizon hobby, inc. E-flite ® products are distributed exclusively by horizon hobby, inc. The spektrum trademark is used with permission of bachmann industries, inc. E-flite, carbon-z, dsm2, bind-n-fly and plug-n-play are trademarks or registered trademarks of horizon hobby, inc. Patents pend...