- DL manuals
- E-FLITE
- Toy
- Maule M7
- Instruction manual
E-FLITE Maule M7 Instruction manual
Summary of Maule M7
Page 1
Instruction manual bedienungsanleitung manuel d’utilisation manuale di istruzioni safe ® select technology, optional flight envelope protection maule m7.
Page 2: 14+
En 2 maule m7 as the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or the property of others. • always keep a safe distance in all directions around your model to avoid collisions or injury. Th...
Page 3: Box Contents
En 3 safety precautions and warnings .................................................................... 2 box contents .................................................................................................. 3 specifi cations ..................................................................
Page 4: Prefl Ight
En 4 maule m7 prefl ight transmitter setup important: after you set up your model, always rebind the transmitter and receiver to set the desired failsafe positions. Dual rates at fi rst fl y with low rate. Notice: to ensure as3x ® technology functions properly, do not lower rate values below 50%. If lo...
Page 5: Model Assembly
En model assembly tail installation 1. Insert the vertical stabilizer into the slot in the horizontal stabilizer. 2. Install the tail assembly and insert the tail wheel wire into the rudder. 3. Secure the tail assembly in place with two 3 x 16mm hex head screws (b) from the top and one 3 x 16mm scre...
Page 6: Model Assembly
En model assembly continued a b b b 3 x 20mm tapered hex head machine a 3 x 16mm tapered hex head machine b wing installation 1. Rotate the wing struts into position in preparation for mounting the wing. 2. Slide the wings onto the wing tube. 3. Connect the servo and light connections together from ...
Page 7: Scale Accessories
En b b 3 x 16mm tapered hex head machine b scale accessories optional float installation optional install the non-functional scale antennas on the top of the wing. Insert the tab into the slot in the plastic fi tting and slide it toward the tail to lock the antenna in place. Float assembly the water ...
Page 8: Receiver Access
En c d 8 maule m7 battery installation and esc arming receiver access battery selection the e-fl ite ® 2200mah 11.1v 3s 30c li-po battery (eflb22003s30) is recommended. Refer to the optional parts list for other recommended batteries. If using a battery other than those listed, the battery should be ...
Page 9
En 9 switching off safe select binding sequence install bind plug rx in bind mode bind tx to rx remove bind plug install bind plug remove bind plug rx in bind mode bind tx to rx this product requires an approved spektrum ™ dsm2 ® /dsmx ® compatible transmitter. Visit www.Bindnfl y.Com for a complete ...
Page 10: Safe
En 10 maule m7 55 – 70mm +/- 3mm control horn and servo arm settings the table to the right shows the factory settings for the control horns and servo arms. Fly the aircraft at factory settings before making changes. Notice: if control throws are changed from the factory settings, the ar636 gain val...
Page 11: As3X Control Direction Test
En 11 as3x control direction test this test ensures that the as3x ® control system is functioning properly. Assemble the aircraft and bind your transmitter to the receiver before performing this test. 1. Raise the throttle just above 25%, then lower the throttle to activate as3x technology. Caution:...
Page 12: Flying Tips and Repairs
En 12 maule m7 flying tips and repairs consult local laws and ordinances before choosing a fl ying location. Range check your radio system before you fl y, range check the radio system. Refer to your specifi c transmitter instruction manual for range test information. Oscillation once the as3x system i...
Page 13: Motor Service
En motor service caution: always disconnect the fl ight battery before performing motor service. 1. Remove the spinner screw (a) and the spinner. 2. Use a tool to remove the propeller nut and then remove the propeller, spinner backplate and prop adaptor from the motor shaft. 3. Remove the four screws...
Page 14: Troubleshooting Guide As3X
En 14 maule m7 troubleshooting guide as3x problem possible cause solution oscillation damaged propeller or spinner replace propeller or spinner imbalanced propeller balance the propeller motor vibration replace parts or correctly align all parts and tighten fasteners as needed loose receiver align a...
Page 15: Troubleshooting Guide
En 15 troubleshooting guide (continued) problem possible cause solution control surface does not move control surface, control horn, linkage or servo damage replace or repair damaged parts and adjust controls wire damaged or connections loose do a check of wires and connections, connect or replace a...
Page 16: Limited Warranty
En 16 maule m7 limited warranty what this warranty covers horizon hobby, llc, (horizon) warrants to the original purchaser that the product purchased (the “product”) will be free from defects in materials and workmanship at the date of purchase. What is not covered this warranty is not transferable ...
Page 17: Fcc Information
En 17 fcc id: brwdasrx15 this equipment has been tested and found to comply with the limits for part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequen...
Page 21
Created 1/18 56566 efl5350, efl5375 © 2018 horizon hobby, llc. E-fl ite, dsm, dsm2, dsmx, bind-n-fly, bnf, the bnf logo, plug-n-play, as3x, safe, the safe logo, modelmatch, z-foam, passport, prophet, ec3, and the horizon hobby logo are trademarks or registered trademarks of horizon hobby, llc. The sp...