1. DL manuals
  2. E-FLITE
  3. Toy
  4. SLICK 3D 480
  5. Instruction Manual

E-FLITE SLICK 3D 480 Instruction Manual

Summary of SLICK 3D 480

  • Page 1

    Arf almost-ready-to-fly slick 3d 480 instruction manual bedienungsanleitung manuel d’utilisation manuale di istruzioni.

  • Page 2

    2 efl slick 3d 480 safety warnings and precautions read and follow all instructions and safety precautions before use. Improper use can result in fire, serious injury and damage to property. Components use only with compatible components. Should any compatibility questions exist, please refer to the...

  • Page 3

    3 efl slick 3d 480 warnungen und sicherheit- svorkehrungen bitte lesen und befolgen sie alle anweisungen und sichervorkehrungen vor dem gebrauch. Falscher, nicht sachgemäßer gebrauch kann feuer, ernsthafte verletzungen und sachbeschädigungen zur folge haben. Komponenten verwenden sie mit dem produkt...

  • Page 4

    4 efl slick 3d 480 avertissements relatifs À la sÉcuritÉ lisez et suivez toutes les instructions relatives à la sécurité avant utilisation. Une utilisation inappropriée peut entraîner un incendie, de graves blessures et des dégâts matériels. Composants utilisez uniquement des composants compatibles....

  • Page 5

    5 efl slick 3d 480 avvertimenti e precauzioni per la sicurezza prima dell’uso leggere attentamente tutte le istruzioni e le precauzioni per la sicurezza. In caso contrario si potrebbero procurare incendi, danni o ferite. Componenti usare solo componenti compatibili. Se ci fossero dubbi riguardo alla...

  • Page 6

    6 efl slick 3d 480 42.1 in (1070mm) 390 sq in (25.1 dm2) 39.5 in (1000mm) 37.5–39.7 oz (1125–1063 g) electric power power: power 480 brushless elektro antrieb power: power 480 brushless moteur électrique (ep): power 480 brushless motore elettrico: power 480 brushless 4-channel (or greater) with 4 se...

  • Page 7

    7 efl slick 3d 480 replacement parts•ersatzteile•piÈces de rechange•pezzi di ricambio part english deutsch français italiano 1. Efl286501 fuselage with hatch rumpf mit haube fuselage avec capot fusoliera con portello 2. Efl286502 wing set with ailerons tragflächenset mit querruder ailes avec aileron...

  • Page 8

    8 efl slick 3d 480 required adhesives•erforderliche klebstoffe•types de colles•adesivi necessari part english deutsch français italiano paapt09 thin ca sekundenkleber dünnflüssig colle cyano fine sottile ca paapt03 medium ca sekundenkleber mittel colle cyano moyenne medio ca paapt15 zip kicker aeros...

  • Page 9

    9 efl slick 3d 480 assembly symbol guide•montage symbole•guide des symboles pour assemblage•guida ai simboli di assemblaggio 15 l r l r use thin ca dünnflüssigen sekundenkleber verwenden utilisez de la colle cyanoacrylate fine usare colla ciano acrilica fine use a felt-tipped pen verwenden sie einen...

  • Page 10

    10 efl slick 3d 480 before starting assembly • remove parts from bag. • inspect fuselage, wing panels, rudder and stabilizer for damage. • if you find damaged or missing parts, contact your place of purchase. If you find any wrinkles in the covering, use a heat gun (han100) and covering glove (han15...

  • Page 11

    11 efl slick 3d 480 1 l r l r separate the aileron from the wing. Nehmen sie das querruder von den tragflächen ab. Retirez l’aileron de l’aile. Staccare gli alettoni dall’ala 2 the control horns for the ailerons have a longer lower tab than the control horns for the rudder and elevator. Make sure yo...

  • Page 12

    12 efl slick 3d 480 5 l r l r 15 mix a small amount of 15-minute epoxy. Use a toothpick to apply epoxy in the slot for the control horn, and to the area of the control horn that fits into the aileron. Fit the control horn in the aileron. The horn will fit snug in the slot. Use a paper towel and isop...

  • Page 13

    13 efl slick 3d 480 8 l r l r m2.5 x 10 x4 use a #1 phillips screwdriver to thread the screw into each of the holes in the wing tip. Remove the screw before proceeding. Drehen sie die schraube mit einem philips # 1 schraubendreher in jedes loch rein und wieder raus. Utilisez un tournevis cruciforme ...

  • Page 14

    14 efl slick 3d 480 12 l r l r place a t-pin in the center of each hinge. Slide the hinges into the slots in the wing. The t-pin will rest against the edge of the wing as shown. Stecken sie eine t-nadel in die mitte jeden scharnieres. Die nadel bleibt beim einstecken dann an der tragflächenkante. Pl...

  • Page 15

    15 efl slick 3d 480 1 l r l r secure the aileron servo in the wing with the servo output facing toward the aileron. The servo lead can be retrieved through the wing root as shown. Thread the servo mounting screws into the pre-drilled holes in the wing. Remove the screws, then lift the servo and appl...

  • Page 16

    16 efl slick 3d 480 4 l r l r x2 m2 x 50 x2 assemble the linkage for the aileron using two ball links and the 2 mm x 50 mm threaded rod. Adjust the length to 2 11 / 16 inches (65 mm) as a starting point for the length of the rod. Montieren sie die querruderanlenkung mit zwei kugelanschlüssen auf der...

  • Page 17

    17 efl slick 3d 480 7 l r l r x4 m2 m2 x4 m2 x 10 x2 adjust the linkage so the aileron is centered and the ball end is aligned with the hole in the control horn. Once set, attach the linkage to the control horn. Position the hardware the same as with the servo arm, sliding the washer on the screw be...

  • Page 18

    18 efl slick 3d 480 4 l r l r m4 x 16 x2 secure the wing panels to the fuselage. Befestigen sie die tragflächen am rumpf. Fixer le panneau de l’aile au fuselage. Fissare l’ala alla fusoliera. 1 a a a=a b=b b b remove the elevators from the stabilizer. Set the elevator and hinges aside. Slide the sta...

  • Page 19

    19 efl slick 3d 480 Î notice: do not cut into the underlying wood. This will weaken the structure and could cause failure in flight. As an option, use a soldering iron or hot knife with light pressure to carefully melt the covering and avoid the potential of cutting into the wood. Î hinweis: schneid...

  • Page 20

    20 efl slick 3d 480 7 place a t-pin in the center of the four elevator hinges. Slide the hinges into position with the t-pin resting against the edge of the control surface. Fit the elevators to the stabilizer. Setzen sie je eine t-nadel in die mitte der vier scharniere. Schieben sie die scharniere ...

  • Page 21

    21 efl slick 3d 480 2 test fit the tail gear wire to the rudder. Make sure the wire is flush with the leading edge of the rudder. If not, lightly trim the slot for the wire to allow the wire to fit flush with the leading edge of the rudder. Passen sie den spornraddraht in dem ruder an. Bitte achten ...

  • Page 22

    22 efl slick 3d 480 6 15 apply epoxy to both the slot in the rudder and to the portion of the tail wheel wire that will contact the rudder using a toothpick. Geben sie mit einem zahnstocher epoxy in den schlitz am ruder und auf den teil des spornraddrahtes der mit dem ruder in verbindung kommt. A l’...

  • Page 23

    23 efl slick 3d 480 10 wick thin ca into the joint between the fuselage and fin to secure the fin to the fuselage. Do not use ca accelerator, as the ca must be allowed to seep into the joint between the fuselage and fin to guarantee the bond between the two. Geben sie dünnflüssigen sekundenkleber zw...

  • Page 24

    24 efl slick 3d 480 12 placez de l’adhésif de masquage à une distance de 1mm autour de la fente du guignol de profondeur. Cela permet d’éviter que la colle époxy coule sur la surface de la gouverne. Prenez le guignol de profondeur. Utilisez du papier abrasif pour gratter sa partie inférieure. Utilis...

  • Page 25

    25 efl slick 3d 480 2 connectez le servo de profondeur à la radio pour placer le servo au neutre. Utilisez un tournevis cruciforme #0 pour fixer la bras au servo, puis retirez la partie inutilisée afin qu’elle n’interfère pas avec le mouvement du servo. Utilisez un foret de 2mm pour agrandir le trou...

  • Page 26

    26 efl slick 3d 480 6 x2 m2 m2 x4 m2 x 10 x2 the installation of the rudder servo follows the same steps as the installation for the elevator servo. Make sure to have the rudder servo connected to the radio system to have it centered when adjusting the length of the rudder linkage. Der einbau des se...

  • Page 27

    27 efl slick 3d 480 3 l r l r 3mm x2 m3 x 3 x2 insert the axle through the larger main wheel. Secure the wheel to the axle using the wheel collar and setscrew. The tapered edge of the wheel collar will face toward the wheel when installed. Tighten the setscrew using a 1.5mm hex wrench. Stecken sie d...

  • Page 28

    28 efl slick 3d 480 7 l r l r with the landing gear resting on a flat surface, adjust the wheel pants as shown. Justieren sie die radschuhe wie abgebildet wenn das fahrwerk auf einer ebenen fläche steht. En plaçant l’avion sur son train et sur une surface plane, ajustez l’orientation du carénage com...

  • Page 29

    29 efl slick 3d 480 3 connect the leads from the motor to the speed control. Use hook and loop tape to mount the speed control in the fuselage. Make sure to position the speed control far enough into the fuselage so the lead from the speed control can be connected to the receiver. Use tie-wraps (not...

  • Page 30

    30 efl slick 3d 480 Î the ar636 settings used for this plane are located on horizonhobby.Com. The installation and setup of this receiver are very important. Incorrect installation of the receiver and or servo linkages and travel could affect flight performance and or bec operation. Please review an...

  • Page 31

    31 efl slick 3d 480 1 use ca to glue the pilot to the cross brace in the canopy. Allow the ca to fully cure before proceeding. Kleben sie den pilot mit sekundenkleber auf die halter in der kabinenhaube. Lassen sie den klebstoff vollständig trocknen bevor sie fortfahren. Utilisez de la colle ca pour ...

  • Page 32

    32 efl slick 3d 480 4 use a pin vise and 1/16-inch (1.5mm) drill bit to drill four holes in the cowl using the paper templates as a guide. Bohren sie mit einem 1,5mm bohrer vier löcher in die motorhaube. Nutzen sie die papierstreifen als schablone. Utilisez un porte foret muni d’un foret de 1.5mm po...

  • Page 33

    33 efl slick 3d 480 caution: never check the motor rotation on the bench with the propeller installed. The plane could move and cause serious injury. To avoid injury, always check the motor without the propeller. Achtung: Überprüfen sie niemals die drehrichtung des motors mit montierten propeller. D...

  • Page 34

    34 efl slick 3d 480 center of gravity an important part of preparing the aircraft for flight is properly balancing the model. 1. Your model should be flight-ready with the battery secured in the fuselage before balancing. 2. The recommended center of gravity (cg) location for your model is 2 15 / 16...

  • Page 35

    35 efl slick 3d 480 control throws 1. Turn on the transmitter and receiver of your model. Check the movement of the rudder using the transmitter. When the stick is moved to the right, the rudder should also move right. Reverse the direction of the servo at the transmitter if necessary. 2. Check the ...

  • Page 36

    36 efl slick 3d 480 dÉbattements 1. Mettez l’émetteur et le récepteur sous tension. Contrôlez les mouvements de la dérive en utilisant votre émetteur. Quand le manche est vers la droite, la dérive doit s’orienter vers la droite. Inversez la direction du servo à l’émetteur si nécessaire. 2. Contrôlez...

  • Page 37

    37 efl slick 3d 480 preflight checklist • charge the transmitter, receiver and motor battery for your airplane. Use the recommended charger supplied with your radio system. Follow the instructions provided with the radio. Charge the radio system the night before each flying session. Charge the trans...

  • Page 38

    38 efl slick 3d 480 daily flight checks • check the battery voltage of the transmitter battery. Do not fly below the manufacturer’s recommended voltage. To do so can crash your aircraft. When you check these batteries, ensure you have the polarities correct on your expanded scale voltmeter. • check ...

  • Page 39

    39 efl slick 3d 480 what this warranty covers horizon hobby, llc. (“horizon”) warrants to the original purchaser that the product purchased (the “product”) will be free from defects in materials and workmanship at the date of purchase. What is not covered this warranty is not transferable and does n...

  • Page 40

    40 efl slick 3d 480 warnung ein ferngesteuertes modell ist kein spielzeug. Es kann, wenn es falsch eingesetzt wird, zu erheblichen verletzungen bei lebewesen und beschädigungen an sachgütern führen. Betreiben sie ihr rc-modell nur auf freien plätzen un beachten sie alle hinweise der bedienungsanleit...

  • Page 41

    41 efl slick 3d 480 durée de la garantie garantie exclusive - horizon hobby, llc. (horizon) garantit que le produit acheté (le « produit ») sera exempt de défauts matériels et de fabrication à sa date d’achat par l’acheteur. La durée de garantie correspond aux dispositions légales du pays dans leque...

  • Page 42

    42 efl slick 3d 480 periodo di garanzia la garanzia esclusiva - horizon hobby, llc., (horizon) garantisce che i prodotti acquistati (il “prodotto”) sono privi di difetti relativi ai materiali e di eventuali errori di montaggio. Il periodo di garanzia è conforme alle disposizioni legali del paese nel...

  • Page 43

    43 efl slick 3d 480 instructions for disposal of weee by users in the european union this product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste ele...

  • Page 44

    44 efl slick 3d 480 effective january 1, 2014 a. General: a model aircraft is a non-human- carrying aircraft capable of sustained flight in the atmosphere. It may not exceed limitations of this code and is intended exclusively for sport, recreation, education and/or competition. All model flights mu...

  • Page 45

    45 efl slick 3d 480

  • Page 46

    46 efl slick 3d 480

  • Page 47

    47 efl slick 3d 480

  • Page 48

    ? 2014 horizon hobby, llc. E-flite, as3x, prophet, precept, dsmx, the dsmx logo and the horizon hobby logo are trademarks or registered trademarks of horizon hobby, llc. The spektrum trademark is used with permission of bachmann industries, inc. All other trademarks, service marks and logos are the ...