1. DL manuals
  2. E-FLITE
  3. Toy
  4. UMX Pitts S-1S
  5. Instruction Manual

E-FLITE UMX Pitts S-1S Instruction Manual

Manual is about: BNF

Summary of UMX Pitts S-1S

  • Page 1

    Instruction manual bedienungsanleitung manuel d’utilisation manuale di istruzioni umx ™ pitts ® s-1s.

  • Page 2

    2 en warning: read the entire instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product. It must be operated ...

  • Page 3: Installed

    3 en t hank you for purchasing the e-fl ite ® umx ™ pitts ® s-1s ultra micro airplane. Despite its size, this model has been engineered to deliver a potent scale model that handles great. Molded lightweight foam construction makes it possible for the high-output brushless power system installed to pr...

  • Page 4: Prefl Ight Checklist

    4 en 1. Charge fl ight battery. 2. Install fl ight battery in aircraft (once it has been fully charged). 3. Bind aircraft to transmitter. 4. Make sure linkages move freely. 5. Perform control direction test with transmitter. 6. Set dual rates and expos. 7. Adjust center of gravity. 8. Perform a radio ...

  • Page 5

    5 en binding is the process of programming the receiver to recognize the guid (globally unique identifi er) code of a single specifi c transmitter. You need to ‘bind’ your chosen spektrum ™ dsm2/dsmx technology equipped aircraft transmitter to the receiver for proper operation. Any full range spektrum...

  • Page 6

    6 en 4 1- 2- 3- 4 -5 sec. 1 2 3 esc/receiver arming, battery installation and center of gravity caution: always keep hands away from the propeller. When armed, the motor will turn the propeller in response to any throttle movement. Arming the esc/receiver also occurs after binding as previously desc...

  • Page 7: Control Centering

    7 en before the fi rst fl ights, or in the event of an accident, make sure the fl ight control surfaces are centered. Adjust the linkages mechanically if the control surfaces are not centered. Use of the transmitter sub-trims may not correctly center the aircraft control surfaces due to the mechanical ...

  • Page 8: Post Flight Checklist

    8 en post flight checklist 1. Disconnect the fl ight battery from the esc (required for safety and battery life). 2. Power off the transmitter. 3. Remove the fl ight battery from the aircraft. 4. Recharge the fl ight battery. 5. Store the fl ight battery apart from the aircraft and monitor the battery c...

  • Page 9: Power Components Service

    9 en power components service disassembly caution: do not handle the propeller while the fl ight battery is connected to the esc. Personal injury could result. Propeller 1. Remove the spinner (a) from the propeller. Since the propeller and spinner are glued together, glue residue will need to be clea...

  • Page 10: As3X

    10 en as3x problem possible cause solution control surfaces not at neutral position when transmitter controls are at neutral control surfaces may not have been mechanically centered from factory center control surfaces mechanically by adjusting the u-bends on control linkages aircraft was moved afte...

  • Page 11: Limited Warranty

    11 en problem possible cause solution led on receiver fl ashes rapidly and aircraft will not respond to transmit- ter (after binding) less than a 5-second wait between fi rst powering on transmitter and connecting fl ight battery to aircraft leaving transmitter on, disconnect and reconnect fl ight batte...

  • Page 12

    12 en of horizon. Proof of purchase is required for all warranty claims. Service or replacement as provided under this warranty is the purchaser’s sole and exclusive remedy. Limitation of liability horizon shall not be liable for special, indirect, incidental or consequential damages, loss of profit...

  • Page 13: Declaration of Conformity

    13 en declaration of conformity compliance information for the european union (in accordance with iso/iec 17050-1) no. Hh2014021501 product(s): efl umx s-1s pitts bnf item number(s): eflu5250 equipment class: 1 the object of declaration described above is in conformity with the requirements of the s...

  • Page 14

    50 replacement parts – ersatzteile – – pièces de rechange – pezzi di ricambio – part # • nummer numéro • codice description beschreibung description descrizione eflu5265 decal set: umx pitts s-1s dekorbogen: umx pitts s-1s set de décoration: umx pitts s-1s set adesivi: umx pitts s-1s eflu5251 spinne...

  • Page 15

    51 – optional parts and accessories – – optionale bauteile und zubehörteile – – pièces optionnelles et accessoires – – pezzi opzionali e accessori – part # • nummer numéro • codice description beschreibung description descrizione pkz1039 hook and loop set (5): ultra micros parkzone: klettband set ul...

  • Page 16

    ? 2014 horizon hobby, inc. E-fl ite, as3x, blade, celectra, umx, dsm, dsm2, dsmx, modelmatch, bind-n-fly, the bind-n-fly logo and the horizon hobby logo are trademarks or registered trademarks of horizon hobby, inc. The spektrum trademark is used with permission of bachmann industries, inc. Futaba is...