- DL manuals
- E2v
- Security Camera
- DIVIINA LM2
- User Manual
E2v DIVIINA LM2 User Manual
Summary of DIVIINA LM2
Page 1
Diviina® lm2 line scan camera 1 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 diviina lm2 camera user manual.
Page 2: Diviina® Lm2
Diviina® lm2 line scan camera 2 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 summary 1 camera overview ............................................................................4 1.1 features .....................................................................................................
Page 3: Diviina® Lm2
Diviina® lm2 line scan camera 3 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 8 appendix b: optical mounts available ...................................................... 24 8.1 f-mount .............................................................................................................
Page 4: Diviina® Lm2
Diviina® lm2 line scan camera 4 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 1 camera overview 1.1 features sensor: 1024 to 4096 pixels, 10 or 14 µm square data rate : 40mpixels on two channels line rate up to 35,5 khz bit depth : 8 bits camera link® interface (base) dimensions: 60 x 60 x 45...
Page 5: Diviina® Lm2
Diviina® lm2 line scan camera 5 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 mechanical and electrical interface size (w x h x l) 60 x 60 x 42 mm weight 210 g (without mount) g lens mount m42 x 1 (by default) f (nikon) or c optional mounts sensor alignment ±200 µm sensor flatness ±30 µm powe...
Page 6: Diviina
Diviina ® lm2 6 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 2 image sensor 2.1 sensor structure the sensor has a odd/even structure in two taps as following : 2.2 response of the sensors . 0 1 2 3 4 5 6 7 8 9 200 300 400 500 600 700 800 900 1000 1100 wavelength ls b/ nj /c m2 8 bi ts 14µm p...
Page 7: Diviina
Diviina ® lm2 7 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 3 camera hardware interface 3.1 mechanical drawings sensor size (pixels #) 1024 2048 4096 x with 14µm sensor (mm) 20.83 13.66 - x with 10µm sensor (mm) 22.88 17.76 7.52 15 15 6 42 12 4 x 2 holes m4 (on the 4 sides) 8mm deep 60 60 s...
Page 8: Diviina
Diviina ® lm2 8 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 3.2 input/output connectors and led 3.2.1 power connector camera connector type: hirose hr10a-7r-6pb (male) cable connector type: hirose hr10a-7p-6s (female) signal pin signal pin pwr 1 gnd 4 pwr 2 gnd 5 pwr 3 gnd 6 camera side des...
Page 9: Diviina
Diviina ® lm2 9 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 3.2.2 camera link output configuration port / bit output data port a0 a0 port a1 a1 port a2 a2 port a3 a3 port a4 a4 port a5 a5 port a6 a6 port a7 a7 port b0 b0 port b1 b1 port b2 b2 port b3 b3 port b4 b4 port b5 b5 port b6 b6 port...
Page 10: Diviina
Diviina ® lm2 10 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 4 standard conformity the diviina cameras have been tested using the following equipment: ¾ a shielded power supply cable ¾ a camera link data transfer cable ref. 14b26-szlb-500-olc (3m) e2v recommends using the same configuration...
Page 11: Diviina
Diviina ® lm2 11 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 5 getting started 5.1 out of the box the contains of the camera box is the following : there is no cdrom delivered with the camera : both user manual (this document) and commcam control software have to be downloaded from the web ...
Page 12: Diviina
Diviina ® lm2 12 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 fov focal plan ccd plan f l w s w f fov l = 5.2 setting up in the system vocabulary : w = size of the sensor line (40,96mm for the 4k 10µm) fov = field of view (width of the web inspected by the sensor line) in mm. L = working dis...
Page 13: Diviina
Diviina ® lm2 13 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 6 camera software interface 6.1 control and interface as all the e2v cameras, the diviina is delivered with the friendly interface control software commcam.Ucl (as “ultimate camera link”) which is based on the genicam standard com...
Page 14: Diviina
Diviina ® lm2 14 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 6.2 serial protocol and command format the camera link interface provides two lvds signal pairs for communication between the camera and the frame grabber. This is an asynchronous serial communication based on rs-232 protocol. The...
Page 15: Diviina
Diviina ® lm2 15 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 6.3 camera commands 6.3.1 information these values allow to identify the camera. They can be accessed through the commcam software in the “info” section all these values are fixed in factory except the camera user id which can be ...
Page 16: Diviina
Diviina ® lm2 16 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 6.3.2 setup • signal source : defines if the data comes from the sensor or the fpga (test pattern). This command is available in the commcam “setup” section : Ö read function : “r srce”; return by the camera: “0” if source from th...
Page 17: Diviina
Diviina ® lm2 17 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 6.3.3 exposure and synchronization • synchronisation mode : timed or triggered, it defines how the grabbing is synchronized. This command is available in the commcam “exposure” section : Ö read function : “r sync”; return by the c...
Page 18: Diviina
Diviina ® lm2 18 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 exposure mode timed : free run this mode doesn’t require an external trigger. In this case, the line period (lp) can be defined in the camera (see below) but the real line period of the camera depends also on the exposure time (ti...
Page 19: Diviina
Diviina ® lm2 19 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 ext trig with integration time controlled (itc) with one trig this mode requires an external trigger ( via cc1). Both exposure time and line period are defined by this trig signal : ¾ the exposure time during the low level of the ...
Page 20: Diviina
Diviina ® lm2 20 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 • exposure time : defines the integration time when set in the camera. This command is available in the commcam “exposure” section : Ö read function : “r tint”; return by the camera : integer from 4 to 65534µs (by step of 1µs) Ö w...
Page 21: Diviina
Diviina ® lm2 21 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 6.3.4 gain and offset • analog global gain : set the amplification gain. This command is available in the commcam “gain & offset” section : the value set is also copied in the both odd and even gains. Ö read function : “r gain”; r...
Page 22: Diviina
Diviina ® lm2 22 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 Ö read function : “r fga1”; return by the camera: value from 0 to 880 corresponding to a gain range of 0 to 31db by step of 0,0351db Ö write function : “w fga1” ; • analog even gain : set the amplification gain on the even tap. Ö ...
Page 23: Diviina
Diviina ® lm2 23 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 7 appendix a: test patterns 7.1 1024 pixels camera the test pattern is composed of 4 successive ramps from 0 to 255 lsb gray values : 7.2 2048 pixels camera the test pattern is composed of 8 successive ramps from 0 to 255 lsb gray...
Page 24: Diviina
Diviina ® lm2 24 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 8 appendix b: optical mounts available 8.1 f-mount f mount: (part number ev50-mount-f) drawing for the additional part (except nikon br3) :.
Page 25: Diviina
Diviina ® lm2 25 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 8.2 c-mount c mount : (part number ev50-mount-c).
Page 26: Diviina
Diviina ® lm2 26 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 9 appendix c : troubleshooting 9.1 camera camera power up 3s no led led color fixed green if commcam connection possible : then the led is hs, else : check power supply and its characteristics contact hotline for rma camera ready.
Page 27: Diviina
Diviina ® lm2 27 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 9.2 commcam connection defect detail solutions commcam can’t find the camera : after launching commcam, the icon of the camera is not visible. • the camera is not powered up or the boot sequence is not finished. • the cameralink c...
Page 28: Diviina
Diviina ® lm2 28 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 10 appendix d : command summary 10.1 information title command features vendorname r vdnm get camera vendor name return string e2v modelname r mdnm get camera model name return string camera id r idnb get camera id. Return max 50 ...
Page 29: Diviina
Diviina ® lm2 29 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 title command features w tint set integration time to in µs, from 1 to 65535 integration time r tint get current integration time w tper set line period to in µs, from tpermin to 65535 if tint > tper, tper is set to tint line peri...
Page 30: Diviina
Diviina ® lm2 30 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 11 appendix e: revision history doc. Revision comments / details camera ref commcam rev a preliminary release firmware 1.0.0 1.1.14.X rev b synchronization modes pattern test firmware 1.0.1 (rev a) 1.1.16.X rev c enable/disable au...
Page 31: Diviina
Diviina ® lm2 31 0994g -diviina lm2 04/11 e2v semiconductors sas 2011 how to reach us home page: www.E2v.Com sales office: europe regional sales office e2v ltd 106 waterhouse lane chelmsford essex cm1 2qu england tel: +44 (0)1245 493493 fax: +44 (0)1245 492492 mailto: enquiries@e2v.Com e2v sas 16 bu...