Summary of M80
Page 1
M80 instruction manual.
Page 2: Warning
Warning please read the entire instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product. It must be operated...
Page 3: Contents
Control. • always operate your model in open spaces away from full-size vehicles, traffic and people. • always carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.). • always keep all chemicals, small parts and anything ...
Page 4: Specifications
Battery-500mah 1s 3.8v 25c lihv x1 charger-1s usb li-po charger x1 transmitter x1 25mw vtx 600tvl fpv camera x1 specifications length: 100mm (3.94in) width：100mm（3.94in） height: 50mm (1.97in) propeller diameter: 40mm (1.57in) flying weight: 52g (1.83oz) first flight preparation • remove and inspect ...
Page 5: Charge The Flight Battery
Never leave charging batteries unattended. Never charge batteries overnight. Never charge damaged batteries. If the battery begins to swell during charging or use, discontinue immediately. Always use the included battery and charger. Disconnect the battery after charging. Charge batteries away from ...
Page 6: Installing The Propellers
Installing the propellers refer to the illustration for the proper motor rotation and propeller location. The propellers are press fit onto the motor shafts. Remove the propellers by pulling the center hub straight up away from the motor. Install the propellers by pressing the center hub over the mo...
Page 7
Batteries discharged to a voltage lower than the lowest approved voltage may become damaged, resulting in loss of performance and potential fire when the batteries are charged. Transmitter and receiver binding 1. Place the drone flat on the floor and then plug in the battery. Green light will briefl...
Page 8: Transmitter Control (Rtf)
Normally. Note: you do not need to do it again once the binding is successful. Power on the remote controller then connected to the battery. Transmitter control (rtf) mode a b c d e f g m1 one key return /air pressure mode throttle (up/down) /roll (left/right) throttle trim /root trim mode switch pi...
Page 9
2. Rotate the two sticks along its inner wall. The led will turn solid and quit calibration mode after recording the maximum and minimum data of sticks successfully. Understanding the primary flight controls if you are not familiar with the controls of your quadcopter, take a few minutes to familiar...
Page 10: Flight Mode Selection
Flight mode selection change flight modes by pressing different buttons on the transmitter. The quadcopter is in stability mode when first powered on. The active flight mode is indicated by the leds at bottom of the quadcopter. Mode leds agility (button d with one click) solid red led stability (but...
Page 11
Altitude. In some cases, you may need to make a few short “hops” to an altitude of just a few inches until you become familiar with the control inputs and trim settings required to maintain a steady hover and altitude. Hovering the quadcopter requires minor throttle adjustments to maintain its altit...
Page 12: Low Voltage Cutoff(Lvc)
Notice: crash damage is not covered under warranty. Low voltage cutoff(lvc) once the battery reaches 3v under load, the esc will continuously lower power supplied to the motor until complete shutdown occurs. This helps prevent over- discharge of the li-po battery. Land immediately once the esc activ...
Page 13: Troubleshooting Guide
Chair. If you start to suffer from motion sickness while flying, lower your chin against your chest. Fly in open areas, away from people, trees, cars, and buildings. The range of the system can be impacted by any obstructions blocking your signal. It is normal to see break up in the video going behi...
Page 14
Does not function and smells burnt after connecting the flight battery flight battery connected with the wrong polarity replace the 3-in-1 board. Connect the flight battery noting proper polarity led on receiver flashes rapidly and quadcopter will not respond to transmitter (during binding) transmit...
Page 15: Warning
Quadcopter flight battery or transmitter battery charge is too low replace or recharge batteries aircraft or transmitter is too close to large metal object, wireless source or another transmitter move aircraft and transmitter to another location and attempt connecting again crashes immediately upon ...
Page 16: Handling and Storage
Failure to exercise care while using this product and comply with the following conditions and guidelines could result in product malfunction, excessive heat, fire, property damage, and ultimately injury. Lithium ion batteries are not toys. For the purposes of this document li-ion, li-po or li-fe ba...