- DL manuals
- Eagle Eye
- Battery Charger
- SCR SERIES
- Operating And Service Instructions
Eagle Eye SCR SERIES Operating And Service Instructions - page 52
Summary of SCR SERIES
Page 2: Jf0026-00
Scr/scrf series battery charger jf0026-00 factory-configured specifications model no. Input voltage vac 1 serial no. Float voltage vdc smart part no. Equalize voltage vdc (items a-f req’d) 1 core (bb####) a b c d e f g h j k l m n 1 - serial number and core (bb####) calculated by factory pos. Smart ...
Page 3: Please Read and Follow
I important safety instructions 1) before using the battery charger, read all instruction and cautionary markings on: a) battery charger, b) battery, c) equipment connected to charger and battery 2) this manual contains important safety and operating instructions, and therefore should be filed for e...
Page 4: Table of Contents
Ii table of contents page no. Scr/scrf battery charger specifications (jf0026-00).......................... (inside front cover) important safety instructions ................................................................................................ I table of contents............................
Page 5
Iii page no. Section v - customer options 1. Ground detection circuits (ej0088 / ej0089 / ej0094 / ej0086) .................................................................. 14 2. Ac power failure alarm relay (ej0085) .....................................................................................
Page 6: Section II
2 section ii installation and operation 1. Safety notice caution! Read “important safety instructions” on page i. There are dangerous voltages within the battery charger cabinet! A. Only qualified personnel should attempt to adjust or service this equipment. B. Refer to instruction manual for servic...
Page 7
3 4. Placing charger in service a. With the ac and dc breakers off and the system in float mode, install the charger making ac and dc connections, as described in section ii, 3, and in accord with local regulations as they apply. B. After connecting the lead from the positive (+) battery terminal to...
Page 8
4 7. Maintenance a. This charger is designed to require a minimum of maintenance. There are no rotating parts except in the optional timer and all components have a nominally indefinite life with no expected aging effect. It should be kept clean, dry and checked periodically to make sure all connect...
Page 9
5 9. Description of operation there are four major sections of the scr three-phase charger, which work together to produce stable, regulated, filtered output. The functions of these four sections may be described as follows. A. The power transformer (t1): this section includes t1 and its associated ...
Page 10: Section III
6 section iii troubleshooting 1. Caution notice before troubleshooting, always isolate and de-energize the charger by opening the ac circuit breaker (cb1) and the dc circuit breaker (cb2). This avoids the possibility of high short circuit current damaging the charger, tools, test equipment, or injur...
Page 11
7 b. Power transformer (t1) 1. With the ac and dc circuit breakers open or off, open the cabinet and carefully check the line voltage across line terminals on tb1, terminals (l1 to l2, l2 to l3 & l3 to l1). If no ac voltage is indicated, refer to section iii, 3, a, 1. Check the wiring connections to...
Page 12
8 2. Note that semiconductors usually short in pairs in bridge circuits, seldom as single units, and it is rare that all six semiconductors in a bridge are found defective. When diodes fail it usually is because of surge voltages. Therefore, surge suppressors (ss1, ss2, ss3 & ss4) should also be che...
Page 13
9 4. Check square wave pattern at test points a1, a2 and a3. Note the 120-degree (5.5 ms) delay between the three patterns (scope synchronized to the 60 hz ac line). If a1 pattern is missing, replace ic3. If a2 or a3 is missing, replace ic4. 5. Check ramp pattern at b1, b2 and b3. Compare with those...
Page 14
10 k. Dc ammeter (m1) 1. The charger dc ammeter is connected in series between the charger output and battery. If open it will indicate zero, or if shorted, it will also indicate zero. First be certain the connections are tight. If still no indication, turn cb1 and cb2 breakers to off, disconnect th...
Page 15
11 section iv system adjustments 1. Voltage adjustments and response when abnormal output voltage exists (or no output current is present), and the previous checks in table a on page 27 “voltage adjust ineffective” have been made without locating the fault, switch the ac breaker (cb1) to off. Switch...
Page 16
12 b. Equalize adjustment 1. Since the equalize adjustment will not affect the float voltage adjustment and requires a higher voltage it should always be made after the float voltage is determined. Use a portable voltmeter of one percent accuracy as in the float adjustment. Set switch (sw1) to “equa...
Page 17
13 2. Current limit response and adjustment a. Checks and adjustments: make certain the charger leads are connected to the battery and that the panel voltmeter indicates the proper polarity. Switch the dc breaker (cb2) to "on" and ac breaker (cb1) to "on". The "ac on" indicating light (ds1) should i...
Page 18
14 section v scr/scrf series battery charger customer options the following pages describe customer options available in scr/scrf series battery chargers. The text describes the basic operational philosophy and theory of operation. Block diagrams (or schematics) for these options are shown in sectio...
Page 19
15 2. Ac power failure alarm relay (ej0085) - with optional indicator light purpose: the purpose of this alarm is to notify the user that the ac input power to the battery charger has been interrupted. A front panel "ac failure" lamp is optional for local indication. Relay contacts are provided for ...
Page 20
16 if it is necessary to adjust the lva threshold in the field, the user must load the battery bank and allow the battery voltage to drop while decreasing the float voltage adjustment to the desired cut-off potential. The lva potentiometer is then adjusted so that the lva relay is activated into the...
Page 21
17 7. Equalize timers purpose: equalize timers are used to switch the charger into equalize charging mode for a set period of time, when required by the batteries. "float" and "equalize" indicating lights mounted on the instrument panel can be included with all timers to indicate the charging mode. ...
Page 22
18 8. Common alarm buzzer (ej0123) purpose: the common alarm buzzer is a charger mounted audible alarm, which is activated when any of several different alarm circuits goes into an alarm state. Description: this circuit simply utilizes a set of contacts on each separate alarm relay. All of the conta...
Page 23
19 12. Zero-center dc ammeter for battery/load monitoring (ej0138) purpose and description: the zero-center dc ammeter (m7) lies within the negative return lead of the battery. A current-sensing shunt (sh2) is provided when the range is greater than 50 amperes. M7 indicates the direction and amount ...
Page 24
20 15. Current limit alarm relay w/indicator light (ej0137) purpose: the current limit alarm provides an alarm signal whenever the battery charger output reaches the maximum limit set by the current limit circuit. An indicator lamp (ds24) mounted on the instrument panel also lights when the current ...
Page 25
21 19. Combined alarm status monitor "casm" pc board assembly (ej0837) note: refer to the drawing (ej0837-xx) on page 49 for additional information. Purpose: the combined alarm-status monitor (casm) provides a comprehensive, cost-effective method to monitor the integrity of the battery charger and t...
Page 26: Section VI
22 section vi component description scr/scrf series battery charger - three phase main frame circuit symbol (note 2) spare? (note 1) component description a1 b three phase input main control module pc board xa1 holder for control module pc board (a1) so1 socket for control module pc board (a1) a14 b...
Page 27
23 circuit symbol (note 2) spare? (note 2) component description r1 bleeder / feedback resistor r2 voltage divider resistor r3 b float adjustment potentiometer r4 voltage divider resistor r5 b equalize adjustment potentiometer scr1 b silicon-controlled rectifier (line 1) scr2 b silicon-controlled re...
Page 28: Component Description
24 component description scr/scrf series battery charger options - single/three phase notes: 1) "b" indicates recommended operating spare part 2) for component placement of circuit symbols, refer to scr/scrf series option schematics in section viii starting on page 34 3) for option replacement parts...
Page 29
25 option number ref. Page circuit symbol spare? (note 1) component description ej0096 38 tm3 b 0-72 hour manual timer ds5 b float indicator light ds6 b equalize indicator light ej0097 39 tm3 b 0-72 hour manual timer ej0120 39 a5 b battery discharging alarm pc board w/relay so5 socket for a5 sh3 dc ...
Page 30
26 option number ref. Page circuit symbol spare? (note 1) component description ej0141 46 k8 b common alarm relay (w/buzzer) au1 common alarm buzzer sw13 buzzer on/off switch r61 voltage dropping resistor r63 voltage dropping resistor ej0143 46 a8 b end of discharge alarm pc board w/relay so8 socket...
Page 31: Section Vii
Pilot light ac & line transformer ac circuit brekaer dc circuit breaker diodes scrs surge suppressors pc board reg. Voltage pc board wave forms voltage adjust current adjust shunt or ammeter float / equalize switch or timer internal wiring external wiring dc voltmeter dc ammeter filter capacitor fil...
Page 33
29.
Page 34
30
Page 35
31.
Page 36
32.
Page 38
Option schematics 34.
Page 39
Scr/scrf series battery charger 35.
Page 40
Option schematics 36.
Page 41
Scr/scrf series battery charger 37.
Page 42
Option schematics 38.
Page 43
Scr/scrf series battery charger 39.
Page 44
Option schematics 40
Page 47
Scr/scrf series battery charger 43.
Page 48
Option schematics 44.
Page 49
Scr/scrf series battery charger 45.
Page 50
Option schematics 46.
Page 51
Scr/scrf series battery charger 47.
Page 57
53 electrical ratings and replacement parts scr/scrf series battery chargers (three phase mainframe) please contact your sales representative for data on models not listed. Scr/scrf battery charger model 24v-50a 24v-75a 24v-100a 24v-125a 24v-150a 24v-175a 24v-200a 24v-250a enclosure type style-2 sty...
Page 58
54 electrical ratings and replacement parts scr/scrf series battery chargers (three phase mainframe) please contact your sales representative for data on models not listed. Scr/scrf battery charger model 48v-50a 48v-75a 48v-100a 48v-125a 48v-150a 48v-175a 48v-200a 48v-250a enclosure type style-2 sty...
Page 59
55 electrical ratings and replacement parts scr/scrf series battery chargers (three phase mainframe) please contact your sales representative for data on models not listed. Scr/scrf battery charger model 130v-25a 130v-35a 130v-50a 130v-75a 130v-100a 130v-125a 130v-150a 130v-200a 130v-250a enclosure ...
Page 60
56 electrical ratings and replacement parts scr/scrf series battery chargers (three phase mainframe) please contact your sales representative for data on models not listed. Scr/scrf battery charger model 130v-300a 130v-400a 130v-600a 260v-25a 260v-50a 260v-75a 260v-100a 260v-150a 260v-200a enclosure...
Page 61: Replacement Parts
57 replacement parts scr/scrf series battery charger options (1ph/3ph) battery charger nominal output 12 vdc 24 vdc 48 vdc 130 vdc 260 vdc option number circuit symbol description manufacturer's part no. Ej0083 a2 hlva alarm control pc board gk0045-01 (specify dc voltage) ds3 low voltage indicating ...
Page 62: Replacement Parts
58 replacement parts scr/scrf series battery charger options (1ph/3ph) battery charger nominal output 12 vdc 24 vdc 48 vdc 130 vdc 260 vdc option number circuit symbol description manufacturer's part no. Ej0120 a5 battery discharging alarm pc board gk0052-01 gk0052-02 gk0052-05 gk0052-06 gk0052-07 d...
Page 63: Replacement Parts
59 replacement parts scr/scrf series battery charger options (1ph/3ph) battery charger nominal output 12 vdc 24 vdc 48 vdc 130 vdc 260 vdc option number circuit symbol description manufacturer's part no. Ej0134 ct1 ac current transformer 75 aac max at0057-01 at0057-01 at0057-01 at0057-01 at0057-01 1...
Page 64: Replacement Parts
60 replacement parts scr/scrf series battery charger options (1ph/3ph) battery charger nominal output 12 vdc 24 vdc 48 vdc 130 vdc 260 vdc option number circuit symbol description manufacturer's part no. Ej0141 au1 common alarm buzzer ra0004-00 ra0004-00 ra0004-00 ra0004-00 ra0004-00 k8 common alarm...
Page 65: Replacement Parts
61 replacement parts scr/scrf series battery charger options (1ph/3ph) battery charger nominal output 12 vdc 24 vdc 48 vdc 130 vdc 260 vdc option number circuit symbol description manufacturer's part no. Ej0837 a24 combined alarm-status monitor 1 form-c control pc board 2 form-c en0014-82 en0014-83 ...
Page 66: Section X
62 section x manual specifications document number: the internal text and graphics contained within this manual are controlled by the battery charger manufacturer's internal part number (ja5036-00). Revision level and dates for this part are listed below. These controls supercede all other available...
Page 67: Jd5022-00
Scr/scrf series battery charger jd5022-00 preventive maintenance procedure maintenance date performed by step (standard features) instructions results clean battery charger • all vents clean and open. • remove dust and debris from inside of unit. ¨ ok ¨ ok check all electrical connections and wiring...
Page 68: Scr/scrf Series
Scr/scrf series basic start-up and shut down instructions start up switch "on" dc circuit breaker. Switch "on" ac circuit breaker. Shut down switch "off" ac circuit breaker. Dc circuit breaker may be left "on" or "off". Note if circuit breakers are not installed, use external devices to remove power...